Parkside PHKS 1350 B2 Používateľská príručka

Kategória
Elektrické náradie
Typ
Používateľská príručka
IAN 273331
CIRCULAR SAW PHKS 1350 B2
CIRCULAR SAW
Translation of the original instructions
HANDKREISSÄGE
Originalbetriebsanleitung
KÉZI KÖRFŰRÉSZ
Az originál használati utasítás fordítása
ROČNA KROŽNA ŽAGA
Prevod originalnega navodila za uporabo
RUČNÍ OKRUŽNÍ PILA
Překlad originálního provozního návodu
RUČNÁ KOTÚČOVÁ PÍLA
Preklad originálneho návodu na obsluhu
GB Translation of the original instructions Page 1
HU Az originál használati utasítás fordítása Oldal 13
SI Prevod originalnega navodila za uporabo Stran 27
CZ Překlad originálního provozního návodu Strana 41
SK Preklad originálneho návodu na obsluhu Strana 55
DE / AT / CH Originalbetriebsanleitung Seite 69
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of
the device.
Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik
funkcióját.
Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.
Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.
Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.
GB
 1
PHKS 1350 B2
Contents
Introduction ......................................................2
Proper use ................................................................. 2
Features ................................................................... 2
Package contents ............................................................ 2
Technical details ............................................................. 2
General Power Tool Safety Warnings ................................3
1. Work area safety .......................................................... 3
2. Electrical safety ........................................................... 3
3. Personal safety ............................................................ 4
4. Power tool use and care .................................................... 4
5. Service .................................................................. 4
Device-specific safety instructions for circular saws .................................. 5
Safety information for circular saw blades ......................................... 6
Original accessories/additional equipment ........................................ 7
Initial operation ..................................................8
Fitting/changing the saw blade .....................................8
Mounting/setting the guide fence ............................................... 8
Connecting the sawdust extraction appliance ...................................... 8
Operation .......................................................8
Switching on and off ......................................................... 8
Setting the cutting angle ....................................................... 8
Setting the cutting depth ....................................................... 9
Working with the circular saw .................................................. 9
Switching the laser on and off .................................................. 9
Set rotational speed .......................................................... 9
Tips and tricks ............................................................... 9
Maintenance and Cleaning ........................................10
Disposal ........................................................10
Disposing of the batteries ..................................................... 10
Warranty .......................................................10
Service .........................................................11
Importer .......................................................11
Translation of the original Conformity Declaration .....................11
2 
GB
PHKS 1350 B2
CIRCULAR SAW PHKS 1350 B2
Introduction
Congratulations on the purchase of your
new appliance. You have selected a high-
quality product. The operating instructions
are part of this product. They contain important in-
formation about safety, use and disposal.
Before using the product, familiarise yourself with
all operating and safety instructions. Use this product
only as described and only for the specified areas
of application. Please also pass these operating
instructions on to any future owner(s).
Proper use
This circular saw (hereinafter "appliance") is
designed for longitudinal, cross and mitre cuts in
firmly supported solid wood, chipboard, plastics
and lightweight construction materials. Any other
uses of or modifications to the device are deemed
to be improper usage and may result in serious
physical injury. Not for commercial use.
Features
Safety lock-out
ON/OFF switch
Cutting depth scale
Allen key SW 6
Locking screw
Base plate
Guide fence slot
Wing screw for guide fence slot
Wing screw for cutting angle preselector
Cutting angle scale
Spindle lock
Auxiliary handle
ON/OFF switch laser
Laser discharge opening
Guide fence
Clamping flange
Clamping screw/plain washer
Blade guard
Release lever for the blade guard
Saw blade
Chip ejector
Vacuum adapter for dust extraction
Rotational speed preselector adjusting wheel
Battery compartment cover
Package contents
1 circular saw
1 guide fence
1 vacuum adapter for dust extraction
1 Allen key SW 6
2 saw blades
2 batteries
1 operating instructions
Technical details
Nominal power input: 1350 W
Rated voltage: 230 V ∼ 50 Hz
(Alternating current)
Idle speed: n
0
2.200–4.700 rpm
Saw blades: 1x Ø 190 mm x 2.5 mm x
Ø 20 mm, 24 teeth
1x Ø 190 mm x 2.5 mm x
Ø 20 mm, 48 teeth
Max. cutting depth: at 0°:
wood/plastic 65 mm
at 45°:
wood/plastic 44 mm
Protection class: II /
(Double shielded)
Noise and vibration data:
Noise measurement determined in accordance
with EN 60745. The A-rated noise level of the
tool is typically:
Noise emission value:
Sound pressure level: L
PA
= 92 dB(A)
Uncertainty: K
PA
= 3 dB
Sound power level: L
WA
= 103 dB(A)
Uncertainty: K
WA
= 3 dB
190mm
max. 56 mm
GB
 3
PHKS 1350 B2
Wear ear protection!
Vibration emission value:
Cutting wood a
h,W
= 2.8 m/s
2
Uncertainty K = 1.5 m/s
2
WARNING!
The vibration level specified in these instructions
has been measured in accordance with the
standardised measuring procedure specified
in EN 60745 and can be used to make equip-
ment comparisons. The specified vibration
emission value can also be used to make an
initial exposure estimate. The vibration level
varies in accordance with the use of the tool
and may be higher than the value specified
in these instructions in some cases. It is easy
to underestimate the vibration load if the
electrical power tool is used regularly in this
manner.
NOTE
Try to keep the vibration loads as low as
possible. Measures to reduce the vibration
load are, e.g. wearing gloves and limiting the
working time. Wherein all states of operation
must be included (e.g. times when the power
tool is switched off and times where the
power tool is switched on but running without
load).
General Power Tool
Safety Warnings
WARNING!
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1. Work area safety
a) Keep work area clean and well lit. Cluttered
or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of flam-
mable liquids, gases or dust. Power tools create
sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
2. Electrical safety
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded)
power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or ground-
ed surfaces, such as pipes, radiators, ranges
and refrigerators. There is an increased risk
of electric shock if your body is earthed or
grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD
reduces the risk of electric shock.
4 
GB
PHKS 1350 B2
3. Personal safety
a) Stay alert, watch what you are doing and
use common sense when operating a power
tool. Do not use a power tool while you are
tired or under the influence of drugs, alcohol
or medication. A moment of inattention while
operating power tools may result in serious
personal injury.
b) Use personal protective equipment. Always
wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes, hard
hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energising
power tools that have the switch on invites
accidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewel-
lery or long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.
4. Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that can-
not be controlled with the switch is dangerous
and must be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many
accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cut-
ting edges are less likely to bind and are easier
to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak-
ing into account the working conditions and
the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
5. Service
a) Have your power tool serviced by a qualified
repair person using only identical replace-
ment parts. This will ensure that the safety of
the power tool is maintained.
GB
 5
PHKS 1350 B2
Device-specific safety instructions for
circular saws
Safety instructions for all saws
Cutting procedures
a) DANGER: Keep hands away from
cutting area and the blade. Keep
your second hand on auxiliary
handle, or motor housing. If both hands are
holding the saw, they cannot be cut by the blade.
b) Do not reach underneath the workpiece. The
guard cannot protect you from the blade below
the workpiece.
c) Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade
teeth should be visible below the workpiece.
d) Never hold piece being cut in your hands
or across your leg. Secure the workpiece to
a stable platform. It is important to support
the work properly to minimize body exposure,
blade binding, or loss of control.
e) Hold the power tool by insulated gripping
surfaces only, when performing an operation
where the cutting tool may contact hidden
wiring or its own cord. Contact with a “live”
wire will also make exposed metal parts of the
power tool “live” and could give the operator an
electric shock.
f) When ripping, always use a rip fence or
straight edge guide. This improves the ac-
curacy of cut and reduces the chance of blade
binding.
g) Always use blades with correct size and
shape (diamond versus round) of arbour
holes. Blades that do not match the mounting
hardware of the saw will run eccentrically, caus-
ing loss of control.
h) Never use damaged or incorrect blade
washers or bolt. The blade washers and bolt
were specially designed for your saw, for opti-
mum performance and safety of operation.
Further safety instructions for all saws
Kickback causes and related warnings
kickback is a sudden reaction to a pinched,
bound or misaligned saw blade, causing an
uncontrolled saw to lift up and out of the work-
piece toward the operator;
when the blade is pinched or bound tightly
by the kerf closing down, the blade stalls and
the motor reaction drives the unit rapidly back
toward the operator;
if the blade becomes twisted or misaligned in
the cut, the teeth at the back edge of the blade
can dig into the top surface of the wood causing
the blade to climb out of the kerf and jump back
toward the operator.
Kickback is the result of saw misuse and/or incor-
rect operating procedures or conditions and can
be avoided by taking proper precautions as given
below.
a) Maintain a firm grip with both hands on the
saw and position your arms to resist kickback
forces. Position your body to either side of the
blade, but not in line with the blade. Kickback
could cause the saw to jump backwards, but kick-
back forces can be controlled by the operator, if
proper precautions are taken.
b) When blade is binding, or when interrupting
a cut for any reason, release the trigger and
hold the saw motionless in the material until
the blade comes to a complete stop. Never
attempt to remove the saw from the work or
pull the saw backward while the blade is in
motion or kickback may occur. Investigate and
take corrective actions to eliminate the cause of
blade binding.
c) When restarting a saw in the workpiece,
centre the saw blade in the kerf and check
that saw teeth are not engaged into the
material. If saw blade is binding, it may walk
up or kickback from the workpiece as the saw is
restarted.
6 
GB
PHKS 1350 B2
d) Support large panels to minimise the risk of
blade pinching and kickback. Large panels
tend to sag under their own weight. Supports
must be placed under the panel on both sides,
near the line of cut and near the edge of the
panel.
e) Do not use dull or damaged blades.
Unsharpened or improperly set blades produce
narrow kerf causing excessive friction, blade
binding and kickback.
f) Blade depth and bevel adjusting locking
levers must be tight and secure before making
cut. If blade adjustment shifts while cutting, it
may cause binding and kickback.
g) Use extra caution when sawing into existing
walls or other blind areas. The protruding blade
may cut objects that can cause kickback.
Lower guard function
a) Check lower guard for proper closing
before each use. Do not operate the saw if
lower guard does not move freely and close
instantly. Never clamp or tie the lower guard
into the open position. If saw is accidentally
dropped, lower guard may be bent. Raise the
lower guard with the retracting handle and
make sure it moves freely and does not touch
the blade or any other part, in all angles and
depths of cut.
b) Check the operation of the lower guard
spring. If the guard and the spring are not
operating properly, they must be serviced be-
fore use. Lower guard may operate sluggishly
due to damaged parts, gummy deposits, or a
build-up of debris.
c) Lower guard may be retracted manually
only for special cuts such as “plunge cuts”
and “compound cuts”. Raise lower guard by
retracting handle and as soon as blade enters
the material, the lower guard must be released.
For all other sawing, the lower guard should
operate automatically.
d) Always observe that the lower guard is
covering the blade before placing saw down
on bench or floor. An unprotected, coasting
blade will cause the saw to walk backwards,
cutting whatever is in its path. Be aware of the
time it takes for the blade to stop after switch is
released.
Supplementary notes
Do not use any grinding discs.
Use only saw blade with diameters correspond-
ing to the label on the saw.
When sawing wood or other materials which
may create dusts that are hazardous to health,
always connect a suitable, certified vacuum
extractor device.
Wear a dust mask when sawing wood.
Use only the recommended saw blades.
Always wear ear protectors.
Do not allow the teeth of the saw blade to overheat.
When sawing plastic, avoid melting the plastic.
Safety information for
circular saw blades
Wear protective gloves!
Wear respiratory protection!
Wear protective glasses!
Wear hearing protection!
GB
 7
PHKS 1350 B2
WARNING! Protect yourself from laser
radiation!
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
P max.: < 1 mW
λ: 650 nm
EN 60825-1: 2007
This appliance contains a Class 2 laser.
NEVER direct the laser beam at people or
animals.
NEVER look directly into the laser beam.
The laser beam can cause serious eye damage.
Do NOT direct the laser beam at strongly
reflective material. Reflected laser beams are
also dangerous.
Any adjustment intended to increase the
intensity of the laser beam is forbidden.
There is a risk of personal injury!
No liability will be accepted for damage
resulting from manipulation of the laser
equipment or from disregarding these safety
instructions.
Caution if other than the controls or adjust-
ments specified here or other procedures
are carried out, this may lead to dangerous
exposure to radiation.
NOTE
If the device is not used according to the
manufacturer’s operating instructions, the
protection provided may be impaired.
DANGER
Mishandling the batteries can cause
fires, explosions, leakages or other
hazards!
Do not throw the batteries into a fire and do
not subject them to high temperatures.
Do not open, deform or short-circuit batteries,
since this can lead to chemical leakage.
Do not attempt to recharge batteries. Do not
charge batteries unless they are explicitly
labelled as "rechargeable". There is a risk of
explosion!
DANGER
Check the condition of the batteries at
regular intervals. Leaking chemicals can
cause permanent damage to the device. Take
particular care when handling damaged or
leaking batteries. Risk of chemical burns!
Wear protective gloves.
Chemicals which leak from a battery can
cause skin irritation. In the event of contact
with the skin, rinse with copious amounts of
water. If the chemicals come into contact with
your eyes, rinse thoroughly with water, do not
rub and consult a doctor immediately.
Keep batteries out of the reach of children.
Children might put batteries into their mouth
and swallow them. If a battery has been
swallowed, seek medical assistance IM-
MEDIATELY.
Do not mix different types of batteries.
Always insert the batteries the right way
round (observe correct polarity) otherwise
there is a danger that they could explode.
If you do not intend to use the device for a
long time, remove the batteries.
Changing the batteries:
Open the cover of the battery compartment
with a suitable Philips screwdriver.
Remove the spent batteries.
Insert two new 1.5 V alkaline button cells (type
AG 13/LR 44, e.g. GPA 76) observing the
correct polarity and screw the battery compart-
ment cover firmly closed.
CAUTION!
If operating and adjustment equipment is used or
procedures other than those specified here are
carried out, this may result in hazardous radiation
exposure.
Original accessories/additional
equipment
Only use the accessories and additional equip-
ment that are specified in the operating instruc-
tions and are compatible with the appliance.
8 
GB
PHKS 1350 B2
Initial operation
The PHKS 1350 B2 circular saw has Intelligent
Power Control. This automatic power delivery
system ensures that for a particular speed range
the power output remains constant when working
on harder and more resistant materials.
Fitting/changing the saw blade
NOTE
All blades used should conform to EN 847-1.
Always pull out the plug from the mains before
changing the saw blade
!
1. Set the cutting depth (using the locking screw )
to the minimum position, 0 mm.
2. Swing the blade guard back using the release
lever and put the device down.
3. Press the spindle lock button
(until it engages)
and use the Allen key to release the clamping
screw/washer . Now remover the clamping
screw/washer and the clamping flange
(see also Fig. A).
Fig. A: Changing the saw blade
4. Remove saw blade .
5. Fitting a saw blade
is carried out in the
reverse order.
6. Press the spindle lock button (until it engages)
and use the Allen key to tighten the clamping
screw/washer .
WARNING!
The arrow on the saw blade
must corre-
spond to the arrow showing the direction of
rotation (running direction shown on the
device).
Ensure that the saw blade
is suitable for the
rotational speed of the tool.
Mounting/setting the guide fence
Loosen the wing screw and insert the guide
fence
into the guide fence slot .
Set the desired cut width with the help of the
scale on the guide fence and the marking
arrow in the base plate (see also Fig. B).
0
45
Fig. B: Cutting width 3 cm
Retighten the wing screw .
Connecting the sawdust extraction
appliance
Attach the adapter for dust extraction to the
chip ejector .
Connect an approved dust and chip extraction
device.
Operation
Switching on and off
Switching on:
Push the safety lock-out to the left or right
and keep it pressed.
Press the ON/OFF switch . Once the saw is
running you can release the safety lock-out .
Switching off:
Release the ON/OFF switch
.
Setting the cutting angle
You can select the cutting angle with the help of the
cutting angle scale .
Release the wing screw on the cutting angle
preselector
, set the desired angle on the
cutting angle scale and then re-tighten the
wing screw.
GB
 9
PHKS 1350 B2
Setting the cutting depth
NOTE
We generally recommend setting the cutting
depth to approx. 3 mm more than the thickness
of the material. This ensures that you achieve
a clean cut.
Release the locking screw
, set the desired
cutting depth on the cutting depth scale and
then re-tighten the locking screw .
Working with the circular saw
1. Switch on the device – as described in "Switching
on and off" – and then place it with the front
edge of the base plate on the material.
2. Align the machine using the guide fence or
by using a marked line.
3. Hold the machine in both hands using the
handles and saw by exerting an even pressure.
Switching the laser on and off
Switching on:
Press the ON/OFF switch laser
.
Switching off:
Press the ON/OFF switch laser
.
NOTE
If the batteries are spent, replace them with
two new 1.5 V alkaline button cells (type
AG 13/LR 44, e.g. GPA 76) .
Set rotational speed
Turn the adjusting wheel to the desired
rotational speed (arrow marking ▲)
(1 = lowest rotational speed/6 = highest rota-
tional speed):
Use the following suggested settings or set the rota-
tional speed on the adjusting wheel
as required.
Material Rotational
speed
setting
Cross cuts & longitudinal cuts in
hard and soft wood (solid wood)
6
Chipboard, fibre board 6
Core board, plywood 6
Coated and veneered boards 6
PVC sheets 3–5
Acrylic glass sheets, perspex 2-4
Aluminium plate 4-6
Aluminium profile 4-6
Plaster board 1-2
Stone wool board 1-2
Cement-bonded particle board 1-2
Tips and tricks
Avoid damaging the cutting edge of sensitive
materials, e.g. coated chipboards or doors, by
sticking masking tape along the cutting line.
Another benefit of this is that it is easier to mark
a line on the tape than on a shiny surface. An
even more effective method of protecting the
cutting edges is to clamp a thin piece of wood
along the cutting line (this wood is also sawn).
10 
GB
PHKS 1350 B2
Maintenance and Cleaning
WARNING! RISK OF INJURY!
Switch the appliance off and remove
the power plug before starting any
work.
The appliance must always be kept clean, dry
and free from oil or grease.
To clean the casing, use a soft dry cloth.
WARNING!
If the connecting cable needs to be replaced,
this must be carried out by the manufacturer
or his representative in order to avoid safety
hazards.
Disposal
The packaging consists of environmentally
friendly material. It can be disposed of in
the local recycling containers.
Do not dispose of power tools in
your normal domestic waste!
European Directive 2012/19/EU requires that worn-
out power tools are collected separately and fed
into an environmentally compatible recycling
process.
Your local community or municipal authorities can
provide information on how to dispose of the worn-
out appliance.
Disposing of the batteries
Batteries must be recycled in accordance
with Directive 2006/66/EC and must not
be disposed of with household refuse.
Battery users are obliged by law to take all
rechargeable and single-use batteries to a collection
point operated by a public authority or a retailer.
The purpose of this obligation is to ensure that
batteries are disposed of in an environmentally
congruent manner. Only dispose of batteries when
they are fully discharged. Batteries must be removed
from the device prior to disposal.
Warranty
The warranty provided for this appliance is
3 years from the date of purchase. This ap-
pliance has been manufactured with care
and inspected meticulously prior to delivery.
Please retain your receipt as proof of purchase.
In the event of a warranty claim, please contact
your Customer Service by telephone. This is
the only way to guarantee free return of your
goods.
The warranty only covers claims for material and
manufacturing defects, not for transport damage,
wearing parts or for damage to fragile components
such as switches or batteries. This appliance is in-
tended solely for private use and not for commercial
purposes. The warranty is deemed void if this product
has been subjected to improper or inappropriate
handling, abuse or modifications which were not
carried out by one of our authorised service centres.
Your statutory rights are not restricted in any way
by this warranty. The warranty period is not pro-
longed by repairs made under the warranty.
This also applies to replaced and repaired parts.
Damage and defects present at the time of purchase
must be reported immediately after unpacking, or
no later than two days after the date of purchase.
Repairs made after expiry of the warranty period
are chargeable.
GB
 11
PHKS 1350 B2
Service
Service Great Britain
Tel.: 0871 5000 720 (£ 0.10/Min.)
IAN 273331
Importer
KOMPERNASS HANDELS GMBH
BURGSTRASSE 21
44867 BOCHUM
GERMANY
www.kompernass.com
Translation of the original
Conformity Declaration
We, KOMPERNASS HANDELS GMBH, Custodian
of Documents: Mr. Semi Uguzlu, BURGSTR. 21,
44867 BOCHUM, DEUTSCHLAND, hereby
declare that this product complies with the
following standards, normative documents and the
EC directives:
Machinery Directive
(2006 / 42 / EC)
EMC (Electromagnetic Compatibility)
(2014 / 30 / EU)
RoHS Directive
(2011 / 65 / EU)
Applied harmonised standards:
EN 60745-1: 2009/A11: 2010
EN 60745-2-5: 2010
EN 55014-1: 2006/A2: 2011
EN 55014-2: 1997/A2: 2008
EN 61000-3-2: 2014
EN 61000-3-3: 2013
EN 60825-1: 2007
Type designation of machine:
Circular saw PHKS 1350 B2
Year of manufacture: 02 - 2016
Serial number: IAN 273331
Bochum, 09/02/2016
Semi Uguzlu
- Quality Manager -
Subject to technical changes in the course
of further developments.
12 
GB
PHKS 1350 B2
HU
 13
PHKS 1350 B2
Tartalomjegyzék
Bevezető .......................................................14
Rendeltetésszerű használat ................................................... 14
Felszereltség ...............................................................14
A csomag tartalma ..........................................................14
Műszaki adatok ............................................................14
Általános biztonsági előírások elektromos kéziszerszámokhoz ..........15
1. Munkahelyi biztonság .....................................................15
2. Elektromos biztonság ......................................................15
3. Személyi biztonság .......................................................16
4. Az elektromos kéziszerszám használata és kezelése ............................. 16
5. Szerviz .................................................................17
Kézi körfűrész készülék-specifikus biztonsági utasítása ..............................17
Biztonsági előírások körfűrészlapokhoz .......................................... 19
Eredeti tartozékok / kiegészítő eszközök .........................................20
Üzembe helyezés ................................................21
Fűrészlap felszerelése / cseréje ................................................ 21
Párhuzamos ütköző felszerelése / beállítása ......................................21
Forgácselszívó csatlakoztatása ................................................ 21
Használat ......................................................22
Be- és kikapcsolás ..........................................................22
Vágási szög beállítása ....................................................... 22
Vágásmélység beállítása ..................................................... 22
A kézi körfűrész kezelése .....................................................22
Lézer be- és kikapcsolása .....................................................22
Fordulatszám beállítása ......................................................22
Ötletek és fogások .......................................................... 23
Karbantartás és tisztítás ..........................................23
Ártalmatlanítás ..................................................23
Elemek ártalmatlanítása ...................................................... 23
Garancia .......................................................24
Szerviz .........................................................24
Importőr .......................................................24
Az eredeti megfelelőségi nyilatkozat fordítása .......................25
14 
HU
PHKS 1350 B2
KÉZI KÖRFŰRÉSZ PHKS 1350 B2
Bevezető
Gratulálunk új készüléke megvásárlásához.
Vásárlásával kiváló minőségű termék mel-
lett döntött. A használati útmutató a termék
része. Fontos tudnivalókat tartalmaz a biztonságra,
használatra és ártalmatlanításra vonatkozóan.
A termék használata előtt ismerkedjen meg vala-
mennyi használati útmutatóval és biztonsági figyel-
meztetéssel. Csak a leírtak szerint és a megadott
célokra használja a készüléket. Ha a készüléket
harmadik személynek továbbadja, akkor adja át a
készülékhez tartozó valamennyi dokumentumot is.
Rendeltetésszerű használat
A kézi körfűrész (a továbbiakban: „készülék“)
tömör fában, faforgácslemezben, műanyag és
könnyűszerkezetű anyagokban történő hosszanti
és keresztvágásra, gérvágásra alkalmas rögzített
alátámasztás mellett. Minden egyéb felhasználási
mód vagy a gép módosítása rendeltetésellenesnek
minősül és jelentős balesetveszélyt rejt magában.
A gép nem ipari használatra készült.
Felszereltség
Kapcsolózár
BE/KI kapcsoló
Vágásmélység-skála
Imbuszkulcs SW 6
Rögzítőcsavar
Alaplemez
Párhuzamos ütköző befogó
Szárnyas csavar a párhuzamos ütköző befogó-
hoz
Szárnyas csavar vágási szög előválasztáshoz
Vágási szög skála
Orsórögzítés
Pótmarkolat
Lézer BE/KI kapcsoló
Lézersugár kilépőnyílása
Párhuzamos ütköző
Befogó perem
Feszítőcsavar / alátét
Védőburkolat
Visszahúzó kar a védőburkolathoz
Fűrészlap
Forgácskivető
Adapter porelszíváshoz
Állítókerék fordulatszám-előválasztáshoz
Elemtartó fedele
A csomag tartalma
1 kézi körfűrész
1 db párhuzamos ütköző
1 adapter porelszíváshoz
1 imbuszkulcs SW 6
2 fűrészlap
2 elem
1 használati útmutató
Műszaki adatok
Névleges teljesítményfelvétel: 1350 W
Névleges feszültség: 230 V ∼ 50 Hz
(váltóáram)
Üresjárati fordulatszám: n
0
2,200 - 4,700 min
-1
Fűrészlapok: 1x Ø 190 mm x 2,5 mm x
Ø 20 mm, 24 fog
Fűrészlapok: 1x Ø 190 mm x 2,5 mm x
Ø 20 mm, 48 fog
Max. vágásmélység: 0° esetén:
Fa/műanyag 65 mm
45° esetén:
Fa/műanyag 44 mm
Védelmi osztály: II /
(dupla szigetelés)
Zaj- és rezgésinformációk:
A zaj mért értékét az EN 60745 szabvány szerint
határoztuk meg. Az elektromos kéziszerszám
A-súlyozott zajszintjének jellemző értéke:
Zajkibocsátási érték:
Zajszint: L
PA
= 92 dB(A)
Bizonytalansági érték: K
PA
= 3 dB
Hangerőszint: L
WA
= 103 dB(A)
Bizonytalansági érték: K
WA
= 3 dB
190mm
max. 56 mm
HU
 15
PHKS 1350 B2
Viseljen hallásvédőt!
Teljes rezgésérték:
Fa fűrészelése a
h,W
= 2,8 m/s
2
Bizonytalansági érték K = 1,5 m/s
2
FIGYELMEZTETÉS!
Jelen használati útmutatóban megadott
rezgésszint az EN 60745 szabvány által
meghatározott szabványos mérési eljárással
lett meghatározva és felhasználható a készü-
lékek összehasonlítására. A megadott rezgés
kibocsátási érték a kitettség előzetes megbe-
csüléséhez is felhasználható. A rezgésszint
az elektromos kéziszerszám alkalmazásától
függően változik és egyes esetekben a jelen
útmutatókban megadott érték felett lehet.
A rezgésterhelés alulbecsült lehet, ha az
elektromos kéziszerszámot rendszeresen így
használják.
TUDNIVALÓ
Próbálja a rezgésterhelést a lehető legalacso-
nyabb szinten tartani. A rezgésterhelés csök-
kentésére tett intézkedések például a keszt
viselése az eszköz használata során és a
munkaidő korlátozása. Ebben az esetben a
működési ciklus minden részét figyelembe kell
venni (például amikor az elektromos kéziszer-
szám ki van kapcsolva, és amikor bár be van
kapcsolva, de terhelés nélkül fut).
Általános biztonsági
előírások elektromos
kéziszerszámokhoz
FIGYELMEZTETÉS!
Olvassa el az összes biztonsági előírást
és utasítást. A biztonsági előírások és
utasítások figyelmen kívül hagyása áramütést,
tüzet és/vagy súlyos sérüléseket okozhat.
Őrizze meg az összes biztonsági előírást és
utasítást későbbi használatra.
A biztonsági előírásokban használt „elektromos
kéziszerszám“ kifejezés hálózatról (hálózati kábe-
len át) üzemeltetett elektromos kéziszerszámokra
és akkumulátoros elektromos kéziszerszámokra
(hálózati kábel nélkül) vonatkozik.
1. Munkahelyi biztonság
a) Tartsa tisztán és jól megvilágítva a munkate-
rületét. A rendetlenség és a rosszul megvilágított
munkaterület balesetet okozhat.
b) Ne dolgozzon a készülékkel olyan robba-
násveszélyes környezetben, ahol gyúlékony
folyadékok, gázok vagy porok vannak.
Az elektromos kéziszerszámok szikráznak, amik
meggyújthatják a port vagy gőzöket.
c) Az elektromos kéziszerszám használata köz-
ben ne engedjen közel gyermekeket és más
személyeket. Ha elterelik a figyelmét, elveszítheti
uralmát a készülék felett.
2. Elektromos biztonság
a) Az elektromos kéziszerszám csatlakozódugójá-
nak illeszkednie kell a csatlakozóaljzatba.
A csatlakozót semmilyen módon nem szabad
megváltoztatni. Ne használjon adaptercsat-
lakozót a védőföldelt elektromos kéziszer-
számmal együtt. A módosítatlan csatlakozó
és a megfelelő csatlakozóaljzat használata
csökkenti az elektromos áramütés veszélyét.
b) Ügyeljen arra, hogy teste ne érintkezzen
földelt felülettel, mint például csővezeték,
fűtőtest, tűzhely vagy hűtőszekrény felületé-
vel. Az áramütés kockázata nagyobb, ha teste
földelve van.
c) Óvja az elektromos kéziszerszámot esőtől
vagy nedves környezettől. Növeli az áramütés
kockázatát, ha víz kerül az elektromos készülék-
be.
16 
HU
PHKS 1350 B2
d) Ne használja a vezetéket rendeltetésellenes
célra, az elektromos kéziszerszámot ne vigye
és ne akassza fel a kábelnél fogva vagy ne a
kábelnél fogva húzza ki a csatlakozót az alj-
zatból. Tartsa távol a vezetéket hőtől, olajtól,
éles szegélyektől vagy mozgó alkatrészektől.
A sérült vagy összecsavarodott vezeték növeli
az áramütés kockázatát.
e) Ha a szabadban dolgozik az elektromos ké-
ziszerszámmal, akkor csak olyan hosszabbító
kábelt használjon, ami kültérre is engedélye-
zett. A kültéri használatra alkalmas hosszabbító
kábellel csökkentheti az áramütés veszélyét.
f) Ha az elektromos kéziszerszám nedves helyen
való használata elkerülhetetlen, használjon
hibaáram védőkapcsolót. A hibaáram védőkap-
csoló használata csökkenti az áramütés veszélyé-
nek kockázatát.
3. Személyi biztonság
a) Legyen mindig figyelmes, figyeljen arra, amit
tesz és hozzáértéssel végezze a munkát az
elektromos kéziszerszámmal. Ne használjon
elektromos kéziszerszámot, ha fáradt, vagy
ha kábítószer, alkohol vagy gyógyszer hatá-
sa alatt áll. Az elektromos kéziszerszám hasz-
nálatakor már egy pillanatnyi figyelmetlenség is
komoly sérüléseket okozhat.
b) Viseljen személyes védőfelszerelést és mindig
vegyen fel védőszemüveget. Az elektromos ké-
ziszerszám jellegének és használatának megfele-
lő személyes védőfelszerelés, például pormaszk,
csúszásmentes biztonsági cipő, védősisak vagy
fülvédő csökkenti a személyi sérülések veszélyét.
c) Előzze meg a készülék véletlenszerű bekap-
csolását. Győződjön meg arról, hogy az
elektromos kéziszerszám ki van kapcsolva,
mielőtt a villamos hálózatra és/vagy az akku-
mulátorra csatlakoztatja, illetve kézbe veszi
vagy viszi. Balesetet okozhat, ha a készülék
hordozása közben az ujja a BE/KI kapcsolón
van vagy a készülék már bekapcsolt állapotban
van, amikor csatlakoztatja az áramellátásra.
d) Távolítsa el a beállításhoz használt szerszá-
mokat vagy csavarkulcsokat az elektromos
kéziszerszám bekapcsolása előtt. A készülék
forgó részében maradt szerszám vagy kulcs
balesetet okozhat.
e) Kerülje a normálistól eltérő testtartást. Vegyen
fel biztonságos álló helyzetet és tartsa meg
folyamatosan az egyensúlyát. Ily módon vá-
ratlan helyzetekben is jobban úrrá tud lenni a
készüléken.
f) Viseljen alkalmas ruházatot. Ne viseljen bő
ruházatot vagy ékszert. Tartsa távol a haját,
ruháját és kesztyűjét a mozgó részektől.
A laza ruházat, az ékszer vagy a hosszú haj
beleakadhat a mozgó részekbe.
g) Amennyiben a készülékhez porelszívó és por-
gyűjtő berendezés is szerelhető, akkor győ-
ződjön meg arról, hogy azok csatlakoztatva
vannak és használatuk helyesen történik.
A porelszívó alkalmazása csökkentheti a por
általi veszélyeztetést.
4. Az elektromos kéziszerszám
használata és kezelése
a) Ne terhelje túl a készüléket. A munkájának
megfelelő elektromos kéziszerszámot hasz-
nálja. A megfelelő elektromos kéziszerszámmal
jobban és biztonságosabban tud dolgozni az
adott teljesítmény-tartományban.
b) Ne használjon olyan elektromos kéziszerszá-
mot, amelyiknek hibás a kapcsolója. A nem
be- és kikapcsolható elektromos kéziszerszám
használata veszélyes és meg kell javíttatni.
c) Húzza ki a csatlakozódugót az aljzatból
és/vagy vegye le az akkumulátort, mielőtt
beállításokat végez a készüléken, tartozéko-
kat cserél vagy a készüléket elteszi. Ezzel a
megelőző biztonsági intézkedéssel megakadá-
lyozható az elektromos kéziszerszám véletlen
bekapcsolása.
HU
 17
PHKS 1350 B2
d) A nem használt elektromos kéziszerszámot
gyermekektől elzárva tárolja. Ne engedje,
hogy olyan személyek használják a készüléket,
akik nem ismerik annak használatát, vagy
nem olvasták az erre vonatkozó utasításokat.
Az elektromos kéziszerszámok veszélyesek, ha
tapasztalatlan személyek használják azokat.
e) Gondosan ápolja az elektromos kéziszer-
számokat. Ellenőrizze, hogy a mozgó részek
tökéletesen működnek és nincsenek beszorul-
va, részei nincsenek eltörve vagy olyannyira
megsérülve, hogy az befolyásolná az elekt-
romos kéziszerszám működését. A készülék
használata előtt javíttassa meg a sérült része-
ket. A rosszul karbantartott elektromos kéziszer-
számok sok balesetet okoznak.
f) A vágószerszámokat tartsa mindig élesen és
tisztán. A gondosan karbantartott éles vágóesz-
közök kisebb valószínűséggel szorulnak be és
könnyebben irányíthatók.
g) Az elektromos kéziszerszámot, a tartozéko-
kat, a betétszerszámokat stb. a használati
utasításnak megfelelően használja. Vegye
figyelembe a munkakörülményeket és az
elvégzendő feladatot. Az elektromos kéziszer-
szám rendeltetésétől eltérő használata veszélyes
helyzeteket teremthet.
5. Szerviz
a) Az elektromos kéziszerszámot csak szakkép-
zett szakemberrel és csak eredeti cserealkatré-
szekkel javíttassa. Ezzel biztosíthatja az elekt-
romos kéziszerszám hosszan tartó biztonságos
működését.
Kézi körfűrész készülék-specifikus
biztonsági utasítása
Biztonsági utasítások minden fűrészhez
Fűrészelés
a) VESZÉLY! Ne nyúljon kezével a
vágási területbe és a fűrészlaphoz.
Másik kezével tartsa a pótmarkolatot
vagy a motorházat. Ha mindkét kezével fogja
a fűrészt, akkor a fűrészlap nem sértheti meg a
kezét.
b) Ne nyúljon a munkadarab alá. A védőburko-
lat nem tudja megvédeni Önt a fűrészlaptól a
munkadarab alatt.
c) Igazítsa a vágásmélységet a munkadarab
vastagságához. Kevesebb mint egy teljes fog-
magasságnak kell láthatónak lenni a munkada-
rab alatt.
d) Soha ne tartsa a kezében, vagy a lába fölött
a fűrészelendő munkadarabot. Rögzítse a
munkadarabot egy stabil befogón. Fontos,
hogy a munkadarabot gondosan rögzítse,
nehogy hozzáérjen a testéhez, beszoruljon a
fűrészlap, vagy elveszítse uralmát a készülék
felett.
e) Az elektromos kéziszerszámot csak a szi-
getelt fogófelületeknél fogja meg, ha olyan
munkát végez, ahol a használt szerszám
rejtett áramvezetékbe vagy saját hálózati
kábelbe ütközhet. A feszültség alatt álló
vezetékkel való kapcsolat az elektromos kézi-
szerszám fémrészeit is feszültség alá helyezi és
elektromos áramütéshez vezet.
f) A hosszanti vágásnál mindig alkalmazzon
ütközőt vagy egyenes élvezetőt. Ez növeli
a vágáspontosságot és csökkenti a fűrészlap
beszorulásának lehetőségét.
g) Mindig megfelelő méretű fűrészlapot használ-
jon alkalmas befogófurattal (pl. csillag vagy
kerek alakút). Ha a fűrészlap nem illik a fűrész
szerelési elemeihez, akkor egyenetlenül forog
és Ön elveszítheti uralmát a készülék felett.
h) Sohase használjon sérült vagy hibás fűrész-
lap-alátétet vagy -csavart. A fűrészlap-alátétet
és -csavart speciálisan az Ön fűrészéhez tervez-
ték az optimális teljesítmény és üzembiztonság
elérésére érdekében.
További biztonsági utasítások minden fűrész-
hez
Visszaütés - okok és megfelelő biztonsági utasí-
tások
A visszaütés a beakadt, beszorult vagy hibásan
beállított fűrészlap hirtelen reakciója, aminek
vetkeztében az elszabadult fűrész felemelke-
dik és a munkadarabból kifelé, a kezelőszemély
irányába mozog;
1 / 1

Parkside PHKS 1350 B2 Používateľská príručka

Kategória
Elektrické náradie
Typ
Používateľská príručka