Parkside PHKSA 20-Li A1 Návod na používanie

IAN 279503

CORDLESS CIRCULAR SAW PHKSA 20-LI A1

CORDLESS CIRCULAR SAW

Translation of the original instructions

AKKU-HANDKREISSÄGE

Originalbetriebsanleitung

AKKUS KÉZI KÖRFŰRÉSZ

Az originál használati utasítás fordítása

AKUMULATORSKA ROČNA

KROŽNA ŽAGA

Prevod originalnega navodila za uporabo

AKU RUČNÍ OKRUŽNÍ PILA

Překlad originálního provozního návodu

AKUMULÁTOROVÁ RUČNÁ

KOTÚČOVÁ PÍLA

Preklad originálneho návodu na obsluhu

GB Translation of the original instructions Page 1

HU Az originál használati utasítás fordítása Oldal 17

SI Prevod originalnega navodila za uporabo Stran 33

CZ Překlad originálního provozního návodu Strana 47

SK Preklad originálneho návodu na obsluhu Strana 63

DE / AT / CH Originalbetriebsanleitung Seite 79

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of

the device.

Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik

funkcióját.

Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.

Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.

Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

A

B

C

BATTERY COMPATIBLE WITH ALL DEVICES OF THE SERIES „PARKSIDE X 20V TEAM“

t41&&%$03%-&44*.1"$5%3*--14#4"-J"

t$03%-&44)"..&3%3*--1"#)-J#

t$03%-&44%3*--1"#4-J$

t$03%-&44*.1"$5%3*7&31%44"-J"

t$03%-&44$*3$6-"34"81),4"-J"

t$03%-&44+*(4"8145%"-J"

t$03%-&444"#3&4"8144"-J"

t$03%-&44"/(-&(3*/%&3184"-J"

t$03%-&44.6-5*163104&500-1".'8-J"

20V max.

18V

PHKSA 20-Li A1

GB

│

1 ■

Contents

Introduction ......................................................2

Intended use ................................................................ 2

Features ................................................................... 2

Package contents ............................................................ 2

Technical data .............................................................. 2

General Power Tool Safety Warnings ................................3

1. Work area safety .......................................................... 3

2. Electrical safety ........................................................... 4

3. Personal safety ............................................................ 4

4. Power tool use and care .................................................... 5

5. Use and handling of the cordless electrical power tool ............................. 5

6. Service .................................................................. 5

Appliance-speciﬁc safety instructions for circular saws ............................... 6

Safety guidelines for battery chargers ............................................ 7

Safety information for circular saw blades ......................................... 8

Original accessories/auxiliary equipment ......................................... 8

Before use .......................................................9

Charging the battery (see ﬁg. C) ................................................ 9

Attaching/disconnecting the battery pack to/from the appliance ....................... 9

Checking the battery charge level ............................................... 9

Checking blade guard functionality .............................................. 9

Operation ......................................................10

Fitting/changing the saw blade ................................................10

Rip fence .................................................................10

Connecting the sawdust extraction device ........................................ 10

Use ............................................................11

Switching on and oﬀ ........................................................11

Setting the cutting angle ......................................................11

Setting the cutting depth ...................................................... 11

Working with the circular saw .................................................11

Switching the laser on and oﬀ .................................................11

Tips and tricks ..............................................................11

Maintenance and cleaning .........................................11

Disposal ........................................................12

Kompernass Handels GmbH warranty ..............................12

Service .........................................................13

Importer .......................................................13

Translation of the original Conformity Declaration .....................14

Ordering a replacement battery ....................................15

Online ordering ............................................................ 15

Telephone ordering ......................................................... 15

PHKSA 20-Li A1

■ 2 │ GB

Introduction

Congratulations on the purchase of your new appli-

ance. You have chosen a high-quality product. The

operating instructions are part of this product. They

contain important information about safety, usage

and disposal. Before using the product, please

familiarise yourself with all operating and safety

instructions. Use the product only as described and

for the range of applications speciﬁed. Please also

pass these operating instructions on to any future

owner.

Intended use

This cordless circular saw (hereinafter "appliance")

is designed for longitudinal, cross and mitre cuts in

ﬁrmly supported solid wood, chipboard, plastics

and lightweight construction materials. Any other

uses of or modiﬁcations to the machine are deemed

to be improper usage and may result in serious

physical injury. Not for commercial use.

Features

Figure A:

Safety lock-out

ON/OFF switch

Cutting depth scale

Release button for battery pack

Battery charge level button/battery display LED

Battery pack

Locking screw

Spindle lock

Base plate

Rip fence slot

Figure B:

ON/OFF switch laser

Auxiliary handle

Laser warning

Laser aperture

Cutting angle scale

Wing screw for cutting angle pre-selector

Wing screw for rip fence slot

Rip fence

Blade guard

Clamping ﬂange

Clamping screw

Release lever for the blade guard

Saw blade

Chip ejector

Vacuum adapter for dust extraction

Hex key

Figure C:

Charger

Red control LED

Green control LED

Package contents

1 cordless circular saw

1 high-speed battery charger

1 battery pack

1 rip fence

1 vacuum adapter for dust extraction

1 hex key

1 saw blade (pre-assembled)

1 operating manual

Technical data

Cordless circular saw: PHKSA 20-Li A1

Rated voltage: 20 V (DC)

Rated idle speed: n

0

3800 rpm

Saw blade: 1x Ø 150 mm x Ø 16

mm, 18 teeth

Max. cutting depth: At 0°: 48 mm

At 45°: 36 mm

Use only the following battery to operate the

cordless tool: PAP 20 A1

Type: LITHIUM ION

Rated voltage: 20 V

(DC)

Capacity: 2 Ah

Cells: 5

150mm

max. 48 mm

PHKSA 20-Li A1

GB

│

3 ■

Use only the following high-speed battery

charger to charge the cordless tool: PLG 20 A1

INPUT:

Rated voltage: 230–240 V

~

, 50 Hz

(AC)

Rated power

consumption: 65 W

Fuse (internal): 3.15 A

T3.15A

OUTPUT:

Rated voltage: 21.5 V

(DC)

Rated current: 2.4 A

Charging time: approx. 60 min

Protection class: II /

(double insulation)

Noise emission value:

Noise measurement value determined in accord-

ance with EN 60745. The A-rated noise level of

the power tool is typically as follows:

Sound pressure level: L

PA

= 77 dB(A)

Uncertainty K: K

PA

= 3 dB

Sound power level: L

WA

= 88 dB (A)

Uncertainty K: K

WA

= 3 dB

Wear hearing protection!

Vibration emission value:

Total vibration values (vector total of three direc-

tions) determined in accordance with EN 60745:

Sawing wood a

h,W

< 2,5 m/s

2

Uncertainty K = 1.5 m/s

2

NOTE

► The vibration emission value and noise emis-

sion levels speciﬁed in these instructions have

been measured in accordance with the stand-

ardised testing procedure speciﬁed and can

be used to make equipment comparisons.

The speciﬁed vibration emission value and

the noise emission values can also be used to

make an initial load estimate.

WARNING!

► Depending on the manner in which the

power tool is being used and, in particular,

the kind of workpiece that is being worked,

the vibration and noise emission values can

deviate and may sometimes exceed the val-

ues given in these instructions. Regular use of

the power tool in this way may cause the user

to underestimate the vibration. Try to keep the

vibration loads as low as possible. Measures

to reduce the vibration load are, e.g. wearing

gloves and limiting the working time. Wherein

all states of operation must be included (e.g.

times when the power tool is switched oﬀ and

times where the power tool is switched on but

running without load).

General Power Tool

Safety Warnings

WARNING!

► Read all safety warnings and all instruc-

tions. Failure to follow the warnings and

instructions may result in electric shock, ﬁre

and/or serious injury.

Save all warnings and instructions for future

reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-

operated (cordless) power tool.

1. Work area safety

a) Keep work area clean and well lit. Cluttered

or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of ﬂam-

mable liquids, gases or dust. Power tools create

sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

PHKSA 20-Li A1

■ 4 │ GB

2. Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools. Unmodiﬁed plugs

and matching outlets will reduce risk of electric

shock.

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of elec-

tric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

3. Personal safety

a) Stay alert, watch what you are doing and

use common sense when operating a power

tool. Do not use a power tool while you are

tired or under the inﬂuence of drugs, alcohol

or medication. A moment of inattention while

operating power tools may result in serious

personal injury.

b) Use personal protective equipment. Always

wear eye protection. Protective equipment

such as dust mask, non-skid safety shoes, hard

hat, or hearing protection used for appropriate

conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools

with your ﬁnger on the switch or energising

power tools that have the switch on invites ac-

cidents.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool

may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use

of dust collection can reduce dust-related haz-

ards.

PHKSA 20-Li A1

GB

│

5 ■

4. Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at

the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and oﬀ. Any power tool that can-

not be controlled with the switch is dangerous

and must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing ac-

cessories or storing power tools. Such preven-

tive safety measures reduce the risk of starting

the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are dan-

gerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may aﬀect the

power tool’s operation. If damaged, have the

power tool repaired before use. Many ac-

cidents are caused by poorly maintained power

tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

g) Use the power tool, accessories and tool

bits, etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed. Use of the

power tool for operations diﬀerent from those

intended could result in a hazardous situation.

5. Use and handling of the cordless

electrical power tool

a) Charge a rechargeable battery unit using only

the charger recommended by the manufac-

turer. Chargers are often designed for a partic-

ular type of rechargeable battery unit. There is

the danger of ﬁre if other types of rechargeable

battery units are used.

b) Only the rechargeable battery units supplied

are to be used with an electrical power tool.

The use of other rechargeable battery units may

lead to the danger of injury or ﬁre.

c) When they are not being used, store re-

chargeable battery units away from paper-

clips, coins, keys, nails, screws or other small

metal objects that could cause the contacts

to be bridged. Short-circuiting the contacts of

a rechargeable battery unit may result in heat

damage or ﬁre.

d) Fluids may leak out of rechargeable battery

units if they are misused. If this happens, avoid

contact with the ﬂuid. If contact occurs, ﬂush

the aﬀected area with water. Seek additional

medical help if any of the ﬂuid gets into your

eyes. Escaping battery ﬂuid may cause skin

irritation or burns.

CAUTION! RISK OF EXPLOSION!

Never charge non-rechargeable

batteries!

Protect the rechargeable battery from

heat, for example from continuous

exposure to sunlight, ﬁre, water and

moisture. There is a risk of explosion.

6. Service

a) Have your power tool serviced by a qualiﬁed

repair person using only identical replace-

ment parts. This will ensure that the safety of

the power tool is maintained.

PHKSA 20-Li A1

■ 6 │ GB

Appliance-speciﬁc safety instructions

for circular saws

Safety instructions for all saws

Sawing method

a) DANGER! Keep your hands clear of

the sawing area and the saw blade.

Hold the auxiliary handle or motor

housing with your other hand. When both

hands are being used to hold the saw, neither

can be injured by the saw blade.

b) Do not reach underneath the workpiece. The

blade guard cannot protect you from the saw

blade below the workpiece.

c) Set the cutting depth to match the thickness

of the workpiece. Less than a full tooth height

should be visible below the workpiece.

d) Never hold the workpiece to be sawn in your

hand or over your leg. Fasten the workpiece

onto a stable working surface. It is important

to fasten the workpiece securely to minimise the

danger of bodily contact, jamming of the saw

blade or loss of control.

e) Hold the power tool only by the insulated

handles when you are carrying out work

during which the accessory tool may come

into contact with concealed power cables or

the tool’s own power cord. Contact with a live

wire will also make exposed metal parts of the

power tool live and could give the operator an

electric shock.

f) When making longitudinal cuts, always use

a rip fence or a straight edge guide. This will

improve the accuracy of your cut and reduce

the likelihood of the saw blade jamming.

g) Always use saw blades of the correct size

and with an appropriate central ﬁxing bore

(e.g. star-shaped or round). Blades that do not

match the mounting hardware of the saw will

run eccentrically, causing loss of control.

h) Never use damaged or incorrect blade wash-

ers or bolts. The blade washers and bolts were

specially designed for your saw, for optimum

performance and safety of operation.

Further safety instructions for all saws

Kickback - causes and corresponding safety

instructions

▯ A kickback is a sudden reaction caused as a

result of the saw blade catching, jamming or

being falsely aligned, causing the saw to jump

up uncontrollably and out of the workpiece in

the direction of the operator;

▯ if the saw blade catches or jams in a narrowing

saw cut, the blade can no longer rotate and the

power of the motor throws the appliance back

in the direction of the operator;

▯ if the saw blade twists in the saw cut or be-

comes misaligned, the teeth at the rear edge of

the saw blade can become caught in the wood

surface, causing the saw blade to jump out of

the cut and the saw to jump backwards in the

direction of the operator.

Kickback is a result of saw misuse and/or incorrect

operating procedures or conditions. This can be

avoided by taking proper precautions as described

below.

a) Hold the saw ﬁrmly in both hands and posi-

tion your arms such that they can absorb the

force of a kickback. Always stand to the side

of the saw blade and never in line with it. If

a kickback occurs, the circular saw may jump

backwards. However, by taking appropriate

precautions the operator can control the kick-

back forces.

b) If the saw blade jams or you stop working,

switch the saw oﬀ and hold it steadily in the

workpiece until the saw blade has completely

stopped turning. Never attempt to remove

the saw from the workpiece or pull it back-

wards while the saw blade is still moving as

this could lead to a kickback. Investigate and

take corrective actions to eliminate the cause of

blade binding.

PHKSA 20-Li A1

GB

│

7 ■

c) If you want to restart a saw that is still in the

workpiece, centre the saw blade in the cut

and check to ensure that the teeth are not

caught anywhere in the workpiece. If the saw

blade catches it can jump out of the workpiece

or cause a kickback when the saw is restarted.

d) Support large panels to minimise the risk of

blade pinching and kickback. Large panels

tend to bend under their own weight. Panels/

boards must be supported on both side: i.e.

both in the vicinity of the saw cut and also at

the edge.

e) Do not use blunt or damaged saw blades.

Saw blades with blunt or misaligned teeth may

cause excessive friction as the saw cut is too

narrow, and this can cause a saw blade jam

and kickback.

f) Before sawing, ensure that the fastenings for

the cut depth and cut angle settings are tight-

ened. If the settings change while sawing, the

saw blade might jam and cause a kickback.

g) Be particularly careful when sawing in ex-

isting walls or other obscured areas. The

inserted saw blade could get caught on hidden

objects and cause a kickback.

Function of the lower blade guard

a) Check whether the lower blade guard closes

properly before each use. Do not operate

the saw if lower blade guard does not move

freely and close instantly. Never clamp or tie

the lower blade guard into the open position.

If the saw is accidentally dropped, lower blade

guard may be bent. Raise the blade guard with

the release lever and make sure it moves freely

and does not touch the blade or any other part

at all angles and cut depths.

b) Check the operation of the lower blade

guard spring. Have the saw serviced before

using it if the lower blade guard and spring

are not working properly. Damaged parts,

sticky deposits or accumulations of chippings

can cause the lower blade guard to operate

slowly.

c) The lower blade guard may be retracted

manually only for special cuts such as "plunge

cuts" and "compound cuts". Raise the lower

blade guard with the release lever and re-

lease it as soon as blade enters the material.

For all other sawing, the lower blade guard

should operate automatically.

d) Always ensure that the lower blade guard is

covering the blade before placing the saw

down on the workbench or ﬂoor. An unpro-

tected, coasting saw blade will move the saw

in the opposite direction to the cutting direction

and saw anything in its path. Always, take into

account that the saw blade takes some time to

stop spinning.

Safety guidelines for battery charg-

ers

■ This appliance may be used by chil-

dren aged 8 years and above and

by persons with limited physical,

sensory or mental capabilities or

lack of experience and knowledge,

provided that they are under super-

vision or have been told how to use

the appliance safely and are aware

of the potential risks. Do not allow

children to use the appliance as a

toy. Cleaning and user maintenance

tasks may not be carried out by chil-

dren unless they are supervised.

PHKSA 20-Li A1

■ 8 │ GB

■

To avoid potential risks, damaged

mains cables should be replaced

by the manufacturer, their customer

service department or a similarly

qualiﬁed person.

The charger is suitable for indoor use only.

WARNING!

■ Do not operate the appliance with a dam-

aged cable, power cable or power plug. A

damaged power cable poses a threat of a

fatal electric shock.

Supplementary notes:

■ Do not use any grinding discs.

■ Use only saw blades with diameters corre-

sponding to the label on the saw.

■ Always use the right saw blade for the material

being worked.

■ Use only saw blades with a speed marking

that corresponds to or is higher than the speed

speciﬁed for the power tool.

■ Saw blades that are intended for use on wood

or similar materials must comply with EN 847-1.

■ When sawing plastic, avoid melting the plastic.

■ Wear a dust mask when sawing.

■ Only use recommended saw blades.

■ Always wear hearing protection!

Safety information for circular saw

blades

Wear protective gloves!

Wear a dust mask!

Wear protective goggles!

Wear hearing protection!

CAUTION! RISK OF EXPLOSION!

Never charge non-rechargeable

batteries!

Original accessories/auxiliary

equipment

■ Only use the accessories and additional

equipment which are speciﬁed in the operat-

ing instructions and are compatible with the

appliance.

WARNING! Protect yourself from

laser radiation!

LASER

2

P max.: < 1 mW • λ: 650 nm •

EN 60825-1:2014

Never look directly into the laser beam or the

opening from which it emerges.

WARNING!

► Looking at a laser beam through optical

instruments (e.g. magnifying glasses etc.)

can cause eye injuries.

► Caution! If operating and adjustment equip-

ment or procedures other than those speciﬁed

here are used, this may result in hazardous

radiation exposure.

■ Never aim the laser beam at reﬂective surfaces,

people or animals. Even brief visual contact

with a laser beam can result in eye injuries.

PHKSA 20-Li A1

GB

│

9 ■

CAUTION!

If operating and adjustment equipment is used or

procedures other than those speciﬁed here are

carried out, this may result in hazardous radia-

tion exposure.

Before use

Charging the battery (see ﬁg. C)

CAUTION!

► Always unplug the appliance before you

remove the battery pack

from or connect

the battery pack to the charger .

NOTE

► Never charge the battery pack if the ambient

temperature is below 10°C or above 40°C.

If a lithium-ion battery is to be stored for an

extended period, the charge level should

be checked regularly. The optimum charge

level is between 50% and 80%. The storage

climate should be cool and dry and the

ambient temperature should be between 0°C

and 50°C.

♦ Connect the battery pack

to the battery

charger (see ﬁg. C).

♦ Insert the power plug into the socket. The red

control LED

lights up.

♦ The green control LED

indicates that the

charging process is complete and the battery

pack is ready.

CAUTION!

♦ If the red control LED

ﬂashes, this means

that the battery pack has overheated and

cannot be charged.

♦ If the red and green control LEDs

both

ﬂash, this means that the battery pack is

broken.

♦ Push the battery pack

back into the appliance.

■ Never recharge a battery pack again im-

mediately after rapid charging. There is a risk

that the battery pack will overheat and this will

reduce the lifespan of the battery.

♦ Switch oﬀ the charger

for at least 15 min-

utes between successive charging sessions.

Also disconnect the power plug from the mains

power socket.

Attaching/disconnecting the battery

pack to/from the appliance

Inserting the battery pack:

♦ Allow the battery pack to click into the

handle.

Removing the battery pack:

♦ Press the release button

and remove the

battery pack .

Checking the battery charge level

♦ Press the battery charge level button to

check the status of the battery (see ﬁg. A). The

charge status will be shown on the battery dis-

play LED as follows:

♦ RED/ORANGE/GREEN = maximum charge

RED/ORANGE = medium charge

RED = low charge – charge the battery

Checking blade guard functionality

♦ Pull the release lever for the blade guard as

far as it will go.

The blade guard

should move without jamming.

When letting go of the release lever for the blade

guard , it should automatically jump back to its

original position.

PHKSA 20-Li A1

■ 10 │ GB

Operation

Fitting/changing the saw blade

Always remove the battery pack before changing

the saw blade !

1. Set the cutting depth (using the locking screw

) to the minimum position, 0 mm.

2. Swing the blade guard

back using the re-

lease lever and put the appliance down.

3. Press the spindle lock button (until it en-

gages) and use the hex key to release the

clamping screw . Now remove the clamping

screw and the clamping ﬂange (see also

ﬁg. A).

Fig. A: Changing the saw blade

4. Remove the saw blade

.

5. Fitting a saw blade is carried out in the

reverse order.

6. Press the spindle lock button

(until it engages)

and use the hex key to tighten the clamping

screw/washer .

WARNING!

► The arrow on the saw blade

must cor-

respond to the arrow showing the direction of

rotation (running direction shown on the

blade guard ).

■ Ensure that the saw blade

is suitable for the

rotational speed of the tool.

Rip fence

♦ Undo the wing screw and insert the rip fence

into the rip fence slot .

♦ Set the desired cut width with the help of the

scale on the rip fence

and the cut out in the

base plate

(see also ﬁg. B).

The right recess in the base plate is for a cutting

angle of 0°. The left-hand recess in the base

plate is for a cutting angle of 45°.

Fig. B: Cutting width 3 cm

♦ Retighten the wing screw .

Connecting the sawdust extraction

device

♦ Attach the adapter for dust extraction to the

chip ejector .

Optional, depending on the diameter of the

dust and sawdust extraction.

♦ Connect an approved dust and chip extraction

device.

NOTE

► When sawing wood or other materials that

create dusts that are hazardous to health,

always connect the appliance to a suitable,

certiﬁed suction appliance.

PHKSA 20-Li A1

GB

│

11 ■

Use

Switching on and oﬀ

Switching on:

♦ Push the safety lock-out to the left or right

and keep it pressed.

♦ Press the ON/OFF switch . Once the saw is

running, you can release the safety lock-out .

Switching oﬀ:

♦ Release the ON/OFF switch

.

Setting the cutting angle

You can select the cutting angle using the cutting

angle scale .

■ Undo the wing screw of the cutting angle pre-

selector , set the desired cutting angle on the

cutting angle scale and then retighten the

wing screw .

Setting the cutting depth

NOTE

► Select a cutting depth of approx. 3 mm more

than the thickness of the material. This ensures

that you achieve a clean cut.

♦ Undo the locking screw

, set the desired cutting

depth on the cutting depth scale

and then

retighten the locking screw

.

Working with the circular saw

1. Switch on the appliance – as described in

“Switching on and oﬀ” – and then place it with

the front edge of the base plate on the mate-

rial.

2. Align the machine using the rip fence

or by

using a marked line.

3. Hold the machine in both hands using the han-

dles and saw by exerting an even pressure.

Switching the laser on and oﬀ

Switching on:

♦ Press the ON/OFF switch laser .

Switching oﬀ:

♦ Press the ON/OFF switch laser

.

Tips and tricks

■ Avoid damaging the cutting edge of sensitive

materials, e.g. coated chip boards or doors, by

sticking masking tape along the cutting line. This

also makes it easier to mark a line on the tape

than on a shiny surface. An even more eﬀective

method of protecting the cutting edges is to

clamp a thin piece of wood along the cutting

line (this wood is also sawn).

Maintenance and cleaning

WARNING! RISK OF INJURY! Always

switch the appliance oﬀ and remove

the battery before carrying out any

work on the appliance.

The cordless hand-held circular saw is mainte-

nance-free.

■ The appliance must always be kept clean, dry

and free from oil or grease.

■ Never allow liquids to get into the appliance.

■ Use a soft, dry cloth to clean the housing.

Never use petrol, solvents or cleansers which

can damage plastic.

■ The blade guard must always move freely and

close automatically. Therefore, keep the area

around the blade guard clean at all times. Re-

move dust and chips by blowing them out with

compressed air or with a brush.

■ If a lithium-ion battery is to be stored for an

extended period, the charge level should be

checked regularly. The optimum charge level is

between 50% and 80%. The optimum storage

environment is cool and dry.

PHKSA 20-Li A1

■ 12 │ GB

NOTE

► Replacement parts not listed (such as batter-

ies, battery charger) can be ordered via our

service hotline.

Disposal

The packaging is made from environmen-

tally friendly material and can be dis-

posed of at your local recycling plant.

Do not dispose of power tools in

your normal household waste!

European Directive 2012/19/EU requires that

worn-out power tools be collected separately and

recycled in an environmentally compatible manner.

Do not dispose of batteries in your

normal household waste!

Defective or worn-out rechargeable batteries must

be recycled according to Directive 2006/66/EC.

Take the battery pack and/or appliance to a

nearby collection facility.

Please consult your local authorities regarding

suitable disposal of worn out power tools/battery

packs.

Kompernass Handels GmbH

warranty

Dear Customer,

This appliance has a 3-year warranty valid from

the date of purchase. If this product has any faults,

you, the buyer, have certain statutory rights. Your

statutory rights are not restricted in any way by the

warranty described below.

Warranty conditions

The validity period of the warranty starts from the

date of purchase. Please keep your original receipt

in a safe place. This document will be required as

proof of purchase.

If any material or production fault occurs within

three years of the date of purchase of the product,

we will either repair or replace the product for you

at our discretion. This warranty service is depend-

ent on you presenting the defective appliance and

the proof of purchase (receipt) and a short written

description of the fault and its time of occurrence.

If the defect is covered by the warranty, your product

will either be repaired or replaced by us. The repair

or replacement of a product does not signify the

beginning of a new warranty period.

Warranty period and statutory claims for

defects

The warranty period is not prolonged by repairs

eﬀected under the warranty. This also applies to

replaced and repaired components. Any damage

and defects present at the time of purchase must

be reported immediately after unpacking. Repairs

carried out after expiry of the warranty period shall

be subject to a fee.

PHKSA 20-Li A1

GB

│

13 ■

Scope of the warranty

This appliance has been manufactured in accordance

with strict quality guidelines and inspected meticu-

lously prior to delivery.

The warranty covers material faults or production

faults. The warranty does not extend to product parts

subject to normal wear and tear or fragile parts such

as switches, batteries, baking moulds or parts made

of glass.

The warranty does not apply if the product has been

damaged, improperly used or improperly maintained.

The directions in the operating instructions for the

product regarding proper use of the product are

to be strictly followed. Uses and actions that are

discouraged in the operating instructions or which

are warned against must be avoided.

This product is intended solely for private use and

not for commercial purposes. The warranty shall be

deemed void in cases of misuse or improper handling,

use of force and modiﬁcations/repairs which have

not been carried out by one of our authorised

Service centres.

Warranty claim procedure

To ensure quick processing of your case, please

observe the following instructions:

■ Please have the till receipt and the item number

(e.g. IAN 12345) available as proof of purchase.

■ You will ﬁnd the item number on the type plate,

an engraving on the front page of the instructions

(bottom left), or as a sticker on the rear or bot-

tom of the appliance.

■ If functional or other defects occur, please

contact the service department listed either by

telephone or by e-mail.

■ You can return a defective product to us free of

charge to the service address that will be provided

to you. Ensure that you enclose the proof of

purchase (till receipt) and information about

what the defect is and when it occurred.

You can download these instructions

along with many other manuals,

product videos and software on

www.lidl-service.com.

Service

WARNING!

► Have the power tool repaired by the service

centre or a qualiﬁed electrician and only

using genuine replacement parts.

This will ensure that the safety of the appli-

ance is maintained.

► Always ensure that the power plug or the

mains cable is replaced only by the manu-

facturer of the appliance or by an approved

customer service provider.This will ensure that

the safety of the appliance is maintained.

Service Great Britain

Tel.: 0871 5000 720 (£ 0.10/Min.)

E-Mail: [email protected]

IAN 279503

Importer

Please note that the following address is not the

service address. Please use the service address

provided in the operating instructions.

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

GERMANY

www.kompernass.com

PHKSA 20-Li A1

■ 14 │ GB

Translation of the original Conformity Declaration

We, KOMPERNASS HANDELS GMBH, document oﬃcer: Mr. Semi Uguzlu, BURGSTR. 21,

44867 BOCHUM, GERMANY, hereby declare that this product complies with the following standards,

normative documents and EC directives:

Machinery Directive

(2006/42/EC)

EC Low Voltage Directive

(2014/35/EU)

EMC (Electromagnetic Compatibility)

(2014/30/EU)

RoHS Directive

(2011/65/EU)*

*The manufacturer bears the full responsibility for compliance with this conformity declaration. The object

of the declaration described above complies with the requirements of the Directive 2011/65/EU of the Eu-

ropean Parliament and Council of 8 June 2011 on the limitations of use of certain dangerous substances

in electrical and electronic appliances.

Applied harmonised standards:

EN 60745-1:2009/A11:2010

EN 60745-2-5:2010

EN 60335-1:2012+A11:2014

EN 60335-2-29:2004/A2:2010

EN 62233:2008

EN 55014-1:2006/A2:2011

EN 55014-2:2015

EN 61000-3-2:2014

EN 61000-3-3:2013

Type designation of machine:

Cordless circular saw PHKSA 20-Li A1

Year of manufacture: 10 - 2016

Serial number: IAN 279503

Bochum, 30/09/2016

Semi Uguzlu

- Quality Manager -

We reserve the right to make technical changes in the context of further product development.

PHKSA 20-Li A1

GB

│

15 ■

Ordering a replacement battery

If you want to order a replacement battery for your appliance, you can do so easily via the Internet on

www.kompernass.com or by telephone.

The price of the replacement battery is €20, including VAT and shipping. Due to limited stocks, this item

may sell out in a relatively short time.

Online ordering

To order a replacement battery from the Accessories Shop:

■ Use your Internet browser to visit www.kompernass.com.

■ Click on the corresponding ﬂag on the right hand side at the bottom of the page to select the desired

country and language.

■ Click on the tab "Accessory Shop" and then select the appropriate replacement battery under the

heading "Topseller".

■ After you have placed the rechargeable battery in the shopping basket, click the "Checkout" button

and follow the on-screen instructions to complete the ordering process.

NOTE

► Online ordering of replacement parts is not possible in all countries. In this case, please contact the

Service hotline.

■ The promotion is limited to one battery per customer/appliance and also to a period of two months

after the promotion. Thereafter the replacement battery can be ordered as a replacement part under

other conditions.

Telephone ordering

Service Great Britain

Tel.: 0871 5000 720 (£ 0.10/Min.) E-Mail: k[email protected]

To ensure a fast processing of your order, have the article number of you appliance to hand (e.g. IAN

279503) in case of questions. The article number can be found on the type plate or the title page of

these instructions.

PHKSA 20-Li A1

■ 16 │ GB

Stránka sa načítava...

Parkside PHKSA 20-Li A1 Návod na používanie

Tento návod je vhodný aj pre

Parkside PHKSA 20-Li A1 Návod na používanie

v iných jazykoch

Súvisiace články

Ostatné dokumenty