Parkside PKO 270 B2 Operation and Safety Notes



COMPRESSOR

Operation and Safety Notes

Original operating instructions

PKO 270 B2

4



KOMPRESOR

Navodila za upravljanje in varnostna opozorila

Originalna navodila za uporabo



KOMPRESSZOR

Kezelési és biztonsági utalások

Eredeti használati utasítás



KOMPRESOR

Pokyny pro obsluhu a bezpečnostní pokyny

Originální návod k obsluze



KOMPRESOR

Pokyny pre obsluhu a bezpečnostné pokyny

Originálny návod na obsluhu

  

KOMPRESSOR

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung



KOMPRESOR

Wskazówki dotyczące obsługi i bezpieczeństwa

Instrukcją oryginalną

Anleitung_LB4_4010403:_ 24.02.2011 10:56 Uhr Seite 1

2

COMPRESSOR



Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of

the device.



Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik

funkcióját.



Pred branjem stran s slikami odprite navzven in se nato seznanite z vsemi funkcijami naprave.



Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.



Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.



Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z

wszystkimi funkcjami urządzenia.

  

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit

allen Funktionen des Gerätes vertraut.

GB Operation and Safety Notes Page 6

HU Kezelési és biztonsági utalások Oldal 18

SI Navodila za upravljanje in varnostna opozorila Stran 31

CZ Pokyny pro obsluhu a bezpečnostní pokyny Strana 43

SK Pokyny pre obsluhu a bezpečnostné pokyny Strana 56

PL Wskazówki dotyczące obsługi i bezpieczeństwa Strona 69

DE/AT/CH Bedienungs- und Sicherheitshinweise Seite 82

KOMPRESOR

KOMPRESSZOR

KOMPRESOR

KOMPRESSOR

KOMPRESOR

Anleitung_LB4_4010403:_ 24.02.2011 10:56 Uhr Seite 2

3

COMPRESSOR

KOMPRESOR

KOMPRESSZOR

KOMPRESOR

KOMPRESSOR

KOMPRESOR

1

10

9

8

12

K

13

1

2

3

4

5

6

7

11

2 3

18

19

20

14

G H

15

17

16

Anleitung_LB4_4010403:_ 24.02.2011 10:57 Uhr Seite 3

4

4 5

6 7

8

22

24

15

9

A

168

15

10

11

22

23

24

23

B

10

11

Anleitung_LB4_4010403:_ 24.02.2011 10:58 Uhr Seite 4

5

10

12 13

D

C

D F

E

C

16

21

11

max

min

18

Anleitung_LB4_4010403:_ 24.02.2011 10:59 Uhr Seite 5

6

GB

Table of contents: Page

1. Introduction ............................................................................8

2. Safety information ..................................................................8-10

3. Layout ....................................................................................10

4. Intended use ..........................................................................10

5. Technical data ........................................................................11

6. Before starting the equipment ................................................11

7. Assembly and starting ............................................................11-12

8. Replacing the power cable .....................................................12

9. Cleaning, maintenance, storage,

ordering spare parts and transport .........................................12-14

10. Disposal and recycling ...........................................................14

11. Possible causes of failure .......................................................15

12. Declaration of conformity .......................................................16

13. Guarantee certificate ..............................................................17

The reprinting or reproduction by any other

means, in whole or in part, of documentation

and papers accompanying products is

permitted only with the express consent of the

ISC GmbH.

Subject to technical changes

Anleitung_LB4_4010403:_ 24.02.2011 10:59 Uhr Seite 6

7

GB

Additional safety instructions

Note the instructions for use!

Wear ear-muffs!

Beware of electrical voltage!

Beware of hot parts!

Important! Do not open the stopcock/pressure regulator until the air hose is

connected.





Warning! The equipment is remote-controlled and may start-up without warning.

Anleitung_LB4_4010403:_ 24.02.2011 10:59 Uhr Seite 7

8

GB

1. Introduction

 Important!

When using the equipment, a few safety

precautions must be observed to avoid injuries

and damage. Please read the complete

operating manual with due care. Keep these

operating instructions in a safe place so that the

information is available at all times. If you give

the equipment to any other person, hand over

this operating manual as well. We cannot

accept any liability for damage or accidents

which arise due to a failure to follow these

instructions and the safety information.

2. Safety information

 CAUTION

Read all the safety regulations and instructions.

Any errors made in following the safety

information and instructions may result in an

electric shock, fire and/or serious injury.

Keep all safety information and instructions

in a safe place for future use.

2.1 Safety information

 Important! The following basic safety

actions must be taken when using this

compressor in order to protect the user

from electric shocks and the risk of injury

and fire. Read and follow these instructions

before using the equipment.

■ Keep your work area tidy

Untidy work areas can result in accidents.

■ Check the ambient conditions

Do not expose the compressor to rain.

Never use the compressor in damp or wet

locations. There is a risk of electric shock!

Provide good lighting.

Do not use the compressor near flammable

liquids or gases. There is a risk of explosion!

■ Protect yourself against electric shocks

Avoid bodily contact with earthed parts, e.g.

pipes, radiators, cookers and refrigerators.

■ Keep children away!

Do not allow other persons to touch the

compressor or cable, keep them away from

your work area.

■ Keep your compressor in a safe place

When unused, the compressor must be

stored in a dry, locked room out of children’s

reach.

■ Do not overload your compressor

It will run better and safer within its quoted

capacity range.

■ Wear suitable work clothes

Never wear loose fitting clothes or jewellery.

They may get caught in moving parts.

Rubber gloves and non-slip shoes are

recommended when working outdoors.

Wear a hair net if you have long hair. Risk of

injury!

■ Do not use the cable for purposes other

than that for which it is designed

Do not carry the compressor by its cable

and do not use the cable to pull the plug out

of the socket. Protect the cable from heat,

oil and sharp edges. The cable/plug could

become damaged.

■ Take care of your compressor

Keep your compressor clean in order to

work well and safely. Follow the

maintenance instructions. Check the power

plug and cable on a regular basis and have

them replaced by an authorized specialist if

they are damaged. Check the extension

cable regularly and replace it if damaged.

■ Pull out the power plug

When not in use and before carrying out any

maintenance work.

■ Avoid unintentional starting

Make sure that the switch is turned off when

connecting to the power supply.

■ When using an extension cable

outdoors

Check that it is approved for outdoor duty

and is marked accordingly.

■ Be alert at all times

Watch what you are doing. Use common

sense when working. Never use the

compressor when you are distracted.

■ Check your compressor for damage

Before using the compressor again,

carefully check the safety devices and any

slightly damaged parts to ensure that they

are in good working order. Check that the

Anleitung_LB4_4010403:_ 24.02.2011 10:59 Uhr Seite 8

9

GB

moving parts are working correctly, that they

do not jam, and that no parts are damaged.

Make sure that all parts are fitted correctly to

ensure that the equipment remains safe to

use. Unless otherwise stated in the

operating instructions, damaged guards and

parts have to be repaired or replaced by a

customer service workshop. Damaged

switches have to be replaced by a customer

service workshop. Never use an electric

power tool with a switch that cannot be

turned on and off.

■ Important!

For your own safety you must only use the

accessories and additional units listed in the

operating instructions or recommended or

specified by the manufacturer. The use of

mounted tools or accessories other than

those recommended in the operating

instructions or catalog may place your

personal safety at risk.

■ Leave all repairs to a qualified

electrician

Repairs must be left strictly to qualified

electricians or the user might suffer an

accident.

■ Noise

Wear ear muffs when you use the

compressor.

■ Replacing the power cable

To prevent hazards, leave the replacement

of damaged power cables strictly to the

manufacturer or a qualified electrician.

There is a risk of electric shock!

■ Inflating tires

Directly after inflating tires, check the

pressure with a suitable pressure gauge, for

example at your filling station.

■ Roadworthy compressors for building

site operations

Make sure that all lines and fittings are

suitable for the maximum permissible

operating pressure of the compressor.

■ Place of installation

Set up the compressor on an even surface.

■ Make sure that all compressed air lines and

fittings are suitable for the maximum

permissible operating pressure of the

compressor.

■ For pressures above 7 bar it is

recommended to use an air line with a

safety cable.

2.2 Safety instructions for working with

compressed air and blasting guns

■ The compressor pump and lines can

become very hot during operation. Touching

these parts will burn you.

■ The air which is sucked in by the

compressor must be kept free of impurities

that could cause fires or explosions in the

compressor pump.

■ When releasing the hose coupling, hold the

hose coupling piece with your hand. This

way, you can protect yourself against injury

from the rebounding hose.

■ Wear safety goggles when working with the

blow-out pistol. Foreign bodies or blown off

parts can easily cause injuries.

■ Do not blow at people with the blow-out

pistol and do not clean clothes while being

worn. Risk of injury!

2.3. Safety information for paint spraying

■ Do not process any paints or solvents with a

flash point below 75° C. There is a risk of

explosion!

■ Do not heat up paints or solvents. There is a

risk of explosion!

■ If hazardous liquids are processed, wear

protective filter units (face guards). Also,

adhere to the safety information provided by

the manufacturers of such liquids.

■ The details and designations of the

Ordinance on Hazardous Substances,

which are displayed on the outer packaging

of the processed material, must be

observed. Additional protective measures

are to be undertaken if necessary,

particularly the wearing of suitable clothing

and masks.

■ Do not smoke during the spraying process

and/or in the work area. There is a risk of

explosion! Paint vapors are easily

combustible.

■ Never set up or operate the equipment in

the vicinity of a fire place, open lights or

sparking machines.

■ Do not store or eat food and drink in the

work area. Paint vapors are harmful to your

Anleitung_LB4_4010403:_ 24.02.2011 10:59 Uhr Seite 9

10

GB

health.

■ The work area must exceed 30 m

3

and

sufficient ventilation must be ensured during

spraying and drying. Do not spray against

the wind. Always adhere to the regulations

of the local police authority when spraying

combustible or hazardous materials.

■ Do not process media such as white spirit,

butyl alcohol and methylene chloride with

the PVC pressure hose. These media will

destroy the pressure hose.

2.4 Operating pressure vessels

■ You must keep your pressure vessel in good

working order, operate the vessel correctly,

monitor the vessel, carry out necessary

maintenance and repair work immediately

and meet the relevant safety precautions.

■ The supervisory authority may enforce

essential control measures in individual

cases.

■ A pressure vessel is not allowed to be used

if it has faults or deficiencies that can

endanger workers or third parties.

■ Check the pressure vessel for signs of rust

and damage each time before using. Do not

use the compressor with a damaged or rusty

pressure vessel. If you discover any

damage, then please contact the customer

service workshop.

Do not lose this safety information.

3. Layout

1. Transport handle

2. Pressure switch

3. Pressure gauge (for reading the vessel

pressure)

4. Pressure regulator

5. Quick-lock coupling (regulated compressed

air)

6. Pressure gauge (for reading the preset

vessel pressure)

7. Pressure vessel

8. Supporting foot

9. Drain plug for condensation water

10. Axle screw

11. Wheel

12. Oil drain plug

13. Compressor pump

14. Compressed air hose

15. Air filter

16. Oil sealing plug

17. ON/OFF switch

18. Oil level window

19. Safety valve

20. Quick-lock coupling (unregulated

compressed air)

21. Oil filler opening

22. Washer

23. Spring washer

24. Nut

4. Intended use

The compressor is designed to generate

compressed air for compressed-air driven tools

which can be driven with an air volume of up to

approx. 270 l/min (e.g. a tire inflator, blow-out

pistol and paint spray gun). Due to the limited

air output it is not possible to use the

compressor to drive tools with very high air

consumption (for example orbital sanders, rod

grinders and hammer screwdrivers). For tools

with high air consumption (e.g. orbital sanders,

rod grinders, hammer screwdrivers), check

whether the compressor’s air output is sufficient

to operate the tool in question. The volume of

air supplied by the compressor must be greater

than the volume of air consumed by the

compressed air tool at its operating pressure.

The equipment may only be used for the tasks it

is designed to handle. Any other use is deemed

to be a case of misuse. The user/operator and

not the manufacturer will be liable for any

damage or injuries of any kind caused as a

result of this.

Please note that our equipment has not been

designed for use in commercial, trade or

industrial applications. Our warranty will be

voided if the equipment is used in commercial,

trade or industrial businesses or for equivalent

purposes.

Anleitung_LB4_4010403:_ 24.02.2011 10:59 Uhr Seite 10

GB

11

5. Technical data

Mains connection: 230 V ~ 50 Hz

Motor rating kW: 1.8 kW

Operating mode: S1

Compressor speed min

-1

: 2850

Operating pressure bar: max. 8

Pressure vessel capacity (in liters): 24

Theoretical intake capacity (l/min): approx. 270

Effective delivery rate at 7 bar: 90l/min

Sound power level L

WA

in dB: 97

K

WA

uncertainty: 4 dB

Protection type: IP20

Weight of the unit in kg: approx. 26

Oil (15W 40): 0.25 l

■ The product meets the requirements of EN

61000-3-11 and is subject to special

connection conditions. This means that use

of the product at any freely selectable

connection point is not allowed.

■ Given unfavorable conditions in the power

supply the product can cause the voltage to

fluctuate temporarily.

■ The product is exclusively intended for use

at connection points that have a continuous

current-carrying capacity of at least 100 A

per phase.

■ As the user, you are required to ensure, in

consultation with your electric power

company if necessary, that the connection

point at which you wish to operate the

product meets the specified requirements.

6. Before starting the equipment

■ Check the equipment for damage which

may have occurred in transit. Report any

damage immediately to the transport

company which was used to deliver the

compressor.

■ Install the compressor near the point of

consumption.

■ Avoid long air lines and supply lines

(extension cables).

■ Make sure that the intake air is dry and

dustfree.

■ Do not install the compressor in a damp or

wet room.

■ The compressor may only be used in

suitable rooms (with good ventilation and an

ambient temperature from +5 °C to 40 °C).

There must be no dust, acids, vapors,

explosive gases or inflammable gases in the

room.

■ The compressor is designed to be used in

dry rooms. It is prohibited to use the

compressor in areas where work is

conducted with sprayed water.

■ The oil level in the compressor pump has to

be checked before putting the equipment

into operation (see 9.4).

7. Assembly and starting

 Important!

You must fully assemble the appliance

before using it for the first time!

You will require the following tools for assembly

and installation:

2 x open-ended wrench size 17 mm (not

included)

7.1 Fitting the wheels (11)

Fit the supplied wheels as shown in Figure 5.

7.2 Fitting the supporting foot (8)

Fit the supplied supporting foot as shown in

Figure 6.

Anleitung_LB4_4010403:_ 24.02.2011 10:59 Uhr Seite 11

12

GB

7.3 Fitting the air filter (15)

Remove the transportation stopper (B) and

screw the air filter (15) securely to the

equipment (Fig. 7, 8). Make sure that the intake

opening on the air filter faces down.

7.4 Changing the transportation cover (A)

Remove the transportation cover from the oil

filler opening (21) and insert the supplied oil

sealing plug (16) into the oil filler opening. (Fig.

9, 10.)

7.5 Mains connection

■ The compressor is equipped with a mains

cable with shock-proof plug. This can be

connected to any 230V ~ 50 Hz shock-proof

socket which is protected by a 16 A fuse.

■ Before you use the machine, make sure that

the mains voltage is the same as the

operating voltage (see the rating plate).

■ Long supply cables, extensions, cable reels

etc. cause a drop in voltage and can

impede motor start-up.

■ At low temperatures below +5°C,

sluggishness may make starting difficult or

impossible.

7.6 ON/OFF switch (Fig. 2)

Pull the ON/OFF switch (17) upwards to switch

on the compressor. To switch off the

compressor, press the ON/OFF switch down.

7.7 Setting the pressure (Fig. 1, 3)

■ Use the pressure regulator (4) to set the

pressure on the pressure gauge (6).

■ The set pressure can be drawn from the

quick-lock coupling (5).

■ The vessel pressure can be read off the

pressure gauge (3).

■ The vessel pressure is drawn from the

quick-lock coupling (20).

7.8 Setting the pressure switch (Fig. 1)

The pressure switch (2) is set at the factory.

Cut-in pressure approx. 6 bar

Cut-out pressure approx. 8 bar

7.9 Fitting the compressed air hose

(Fig. 1, 3)

Use the compressed air hose (14) if you intend

to carry out work at a greater distance from the

compressor. To do so, connect the nipple (H)

on the compressed air hose to one of the quick-

release couplings (5, 20). Then attach the

compressed air tool to the quick-release

coupling (G) on the compressed air hose.

8. Replacing the power cable

If the power cable for this equipment is

damaged, it must be replaced by the

manufacturer or its after-sales service or

similarly trained personnel to avoid danger.

9. Cleaning, maintenance,

storage, ordering spare parts

and transport

 Important!

Pull out the power plug before doing any

cleaning and maintenance work on the

equipment.

Risk of injury from electric shock!

 Important!

Wait until the equipment has cooled down

completely! Risk of burns!

 Important!

Always depressurize the equipment before

carrying out any cleaning and maintenance

work (see 9.7.1)! Risk of injury!

9.1 Cleaning

■ Keep the equipment free of dirt and dust as

far as possible. Wipe the equipment with a

clean cloth or blow it down with compressed

air at low pressure.

■ We recommend that you clean the

equipment immediately after you use it.

■ Clean the equipment regularly with a damp

cloth and some soft soap. Do not use

cleaning agents or solvents; these may be

aggressive to the plastic parts in the

equipment. Ensure that no water can get

Anleitung_LB4_4010403:_ 24.02.2011 10:59 Uhr Seite 12

13

GB

into the interior of the equipment.

■ You must disconnect the hose and any

spraying tools from the compressor before

cleaning. Do not clean the compressor with

water, solvents or the like.

9.2 Maintenance work on the pressure

vessel (Figure 1)

Important! To ensure a long service life of the

pressure vessel (7), drain off the condensed

water by opening the drain valve (9) each time

after using. Release the vessel pressure first

(see 9.7.1). Open the drain screw by turning

counter-clockwise (looking at the screw from

the bottom of the compressor) so that all the

condensed water can run out of the pressure

vessel. Then close the drain screw again (turn it

clockwise). Check the pressure vessel for signs

of rust and damage each time before using. Do

not use the compressor with a damaged or

rusty pressure vessel. If you discover any

damage, then please contact the customer

service workshop.

 Important!

The condensed water from the pressure

vessel will contain residual oil. Dispose of

the condensed water in an environmentally

compatible manner at a suitable collection

point.

9.3 Safety valve (Figure 3)

The safety valve (19) has been set for the

highest permitted pressure of the pressure

vessel. It is prohibited to adjust the safety valve

or remove its seal. Actuate the safety valve

from time to time to ensure that it works when

required. Pull the ring with sufficient force until

you can hear the compressed air being

released. Then release the ring again.

9.4 Checking the oil level at regular

intervals (Figure 11)

Place the compressor on a level and straight

surface. The oil level must be between the MAX

and MIN marks on the oil level window (Fig.

18). Oil change: we recommend SAE 15W 40

or equivalent. The original oil filling must be

changed after 100 hours in operation; thereafter

the oil must be drained and replaced with new

oil after every 500 hours in operation.

9.5 Changing the oil (Figure 1,10, 11)

Switch off the motor and pull the mains plug out

of the socket. After releasing any air pressure

(see 9.7.1) you can unscrew the oil drain screw

(12) from the compressor pump (13). To

prevent the oil from running out in an

uncontrolled manner, hold a small metal chute

under the opening and collect the oil in a

container. If the oil does not drain out

completely, we recommend tilting the

compressor slightly. When the oil has drained

out, refit the oil drain screw (12).

Dispose of the old oil at a drop-off point for

old oil.

To fill in the correct quantity of oil, make sure

that the compressor stands on an even surface.

Fill new oil through the oil filler opening (21)

until it comes up to the maximum level. This is

marked with a red dot on the oil level window

(18) (Figure 11). Do not exceed the maximum

filling quantity. Overfilling the equipment may

result in damage. Reinsert the oil sealing plug

(16) into the oil filler opening (21).

9.6 Cleaning the intake filter

(Figure 3, 12, 13)

The intake filter prevents dust and dirt being

drawn in. It is essential to clean this filter after at

least every 300 hours in operation. A clogged

intake filter will decrease the compressor’s

performance dramatically. Open the thumb

screw (E) to the remove the intake filter. Then

pull off the filter cover (C). Now you can remove

the air filter (F) and the filter housing (D).

Carefully tap out the air filter, filter cover and

filter housing. Then blow out these parts with

compressed air (approx. 3 bar) and reinstall in

reverse order.

Anleitung_LB4_4010403:_ 24.02.2011 10:59 Uhr Seite 13

14

GB

9.7 Storage

 Important!

Pull out the mains plug and ventilate the

equipment and all connected pneumatic

tools (see 9.7.1). Switch off the compressor

and make sure that it is secured in such a

way that it cannot be started up again by

any unauthorized person.

 Important!

Store the compressor only in a dry location

which is not accessible to unauthorized

persons. Always store upright, never tilted!

Oil may leak out!

9.7.1 Releasing excess pressure

Release the excess pressure by switching off

the compressor and using the compressed air

which is still left in the pressure vessel, e.g. with

a compressed air tool running in idle mode or

with a blow-out pistol.

9.8 Ordering spare parts

The following information is required for all

orders for spare parts:

■ Equipment model/type

■ Equipment article number

■ Equipment ID number

For our latest prices and information please go

to www.isc-gmbh.info

9.9 Transport (Figure 1)

■ Switch off the equipment and pull out the

power plug before lifting and moving the

compressor.

■ Use the transport handle (1) to move the

compressor.

■ Use the transport handle (1) and the grip (K)

on the pressure vessel (7) to lift the

compressor.

Note the equipment’s weight!

■ Transport the compressor only in an upright

position and secure it against tilting so that

no oil runs out.

■ Secure the compressor in accordance with

the regulations in force for transporting

equipment in motor vehicles.

10. Disposal and recycling

The equipment is supplied in packaging to

prevent it from being damaged in transit. The

raw materials in this packaging can be reused

or recycled. The equipment and its accessories

are made of various types of material, such as

metal and plastic. Defective components must

be disposed of as special waste. Ask your

dealer or your local council.

For EU countries only

Never place any electric power

tools in your household refuse.

To comply with European Directive 2002/96/EC

concerning old electric and electronic

equipment and its implementation in national

laws, old electric power tools have to be

separated from other waste and disposed of in

an environment-friendly fashion, e.g. by taking

to a recycling depot.

Recycling alternative to the return request:

Instead of returning the equipment to the

manufacturer, the owner of the electrical

equipment is obliged to ensure that the

equipment is properly disposed of if he

abandons ownership. The old equipment can

be returned to a suitable collection point that

will dispose of the equipment in accordance

with the national recycling and waste disposal

regulations. This does not apply to any

accessories or aids without electrical

components supplied with the old equipment .

Anleitung_LB4_4010403:_ 24.02.2011 10:59 Uhr Seite 14

15

GB

11. Possible causes of failure

Problem Cause Solution

The compressor does not

start.

1. No supply voltage.

2. Insufficient supply voltage.

3. Outside temperature is too

low.

4. Motor is overheated.

1. Check the supply voltage,

the power plug and the

socket-outlet.

2. Make sure that the

extension cable is not too

long. Use an extension cable

with large enough wires.

3. Never operate with an

outside temperature of

below +5° C.

4. Allow the motor to cool

down. If necessary, remedy

the cause of the overheating.

The compressor starts but

there is no pressure.

1. The non-return valve leaks.

2. The seals are damaged.

3. The drain plug for

condensation water (9)

leaks.

1. Have a service center

replace the non-return valve.

2. Check the seals and have

any damaged seals replaced

by a service center.

3. Tighten the screw by hand.

Check the seal on the screw

and replace if necessary.

The compressor starts,

pressure is shown on the

pressure gauge, but the

tools do not start.

1. The hose connections (G,

H) have a leak.

2. A quick-lock coupling (5, 20)

has a leak.

3. Insufficient pressure set on

the pressure regulator (4).

1. Check the compressed air

hose and tools and replace if

necessary.

2. Check the quick-lock

coupling and replace if

necessary.

3. Increase the set pressure

with the pressure regulator.

Anleitung_LB4_4010403:_ 24.02.2011 10:59 Uhr Seite 15

16

GB

12. Declaration of conformity

k erklärt folgende Konformität gemäß EU-Richtlinie und

Normen für Artikel

t explains the following conformity according to EU

directives and norms for the following product

p déclare la conformité suivante selon la directive CE et les

normes concernant l’article

C dichiara la seguente conformità secondo la direttiva UE e

le norme per l’articolo

N verklaart de volgende overeenstemming conform EU

richtlijn en normen voor het product

m declara la siguiente conformidad a tenor de la directiva y

normas de la UE para el artículo

O declara a seguinte conformidade, de acordo com a

directiva CE e normas para o artigo

l attesterer følgende overensstemmelse i medfør af

EU-direktiv samt standarder for artikel

U förklarar följande överensstämmelse enl. EU-direktiv och

standarder för artikeln

q vakuuttaa, että tuote täyttää EU-direktiivin ja standardien

vaatimukset

. tõendab toote vastavust EL direktiivile ja standarditele

j vydává následující prohlášení o shodě podle směrnice

EU a norem pro výrobek

X potrjuje sledečo skladnost s smernico EU in standardi za

izdelek

W vydáva nasledujúce prehlásenie o zhode podľa smernice

EÚ a noriem pre výrobok

A a cikkekhez az EU-irányvonal és Normák szerint a

következő konformitást jelenti ki

P deklaruje zgodność wymienionego poniżej artykułu z

następującymi normami na podstawie dyrektywy WE.

e декларира съответното съответствие съгласно

Директива на ЕС и норми за артикул

H paskaidro šādu atbilstību ES direktīvai un standartiem

G apibūdina šį atitikimą EU reikalavimams ir prekės

normoms

Q declară următoarea conformitate conform directivei UE

şi normelor pentru articolul

z δηλώνει την ακόλουθη συμμόρφωση σύμφωνα με την

Οδηγία ΕΚ και τα πρότυπα για το προϊόν

B potvrđuje sljedeću usklađenost prema smjernicama EU

i normama za artikl

Izjava o sukladnosti za ovaj proizvod dostupna je na

internet stranici www.lidl.hr.

f potvrđuje sljedeću usklađenost prema smjernicama EU

i normama za artikl

4 potvrđuje sledeću usklađenost prema smernicama EZ i

normama za artikal

T следующим удостоверяется, что следующие

продукты соответствуют директивам и нормам ЕС

1 проголошує про зазначену нижче відповідність

виробу директивам та стандартам ЄС на виріб

Z Ürünü ile ilgili AB direktifleri ve normları gereğince

aşağıda açıklanan uygunluğu belirtir

L erklærer følgende samsvar i henhold til EU-direktivet

og standarder for artikkel

E Lýsir uppfyllingu EU-reglna og annarra staðla vöru

Konformitätserklärung

Einhell Germany AG · Wiesenweg 22 · D-94405 Landau/Isar

Kompressor PKO 270 B2 (Parkside)

Standard references: EN 1012-1; EN 61000-6-1;

EN 61000-6-3; EN 61000-3-2; EN 61000-3-11

Landau/Isar, den 29.11.2010

First CE: 10 Archive-File/Record: 4010400-15-4155050-10

Art.-No.: 40.104.03 I.-No.: 11010 Documents registrar: Siegfried Roider

Subject to change without notice Wiesenweg 22, D-94405 Landau/Isar

Weichselgartner/General-Manager Wang/Product-Management

x

87/404/EC_2009/105/EC

2005/32/EC_2009/125/EC

2006/95/EC

2006/28/EC

2004/108/EC

2004/22/EC

1999/5/EC

97/23/EC

90/396/EC_2009/142/EC

89/686/EC_96/58/EC

x

2006/42/EC

2004/26/EC

Emission No.:

2000/14/EC_2005/88/EC

Annex IV

Notified Body:

Notified Body No.:

Reg. No.:

Annex V

Annex VI

Noise: measured L

WA

= 92 dB (A); guaranteed L

WA

= 97 dB (A)

P = 1,8 KW; L/Ø = cm

Notified Body: TÜV SÜD Industrie Service GmbH, 0036

Anleitung_LB4_4010403:_ 24.02.2011 10:59 Uhr Seite 16

17

GB

13. GUARANTEE CERTIFICATE

Dear Customer,

All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely

event that your device develops a fault, please contact our service department at the address shown on this

guarantee card. Of course, if you would prefer to call us then we are also happy to offer our assistance under

the service number printed below. Please note the following terms under which guarantee claims can be made:

1. These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights.

We do not charge you for this guarantee.

2. Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the

rectification of these defects or replacement of the device. Please note that our devices have not been

designed for use in commercial, trade or industrial applications. Consequently, the guarantee is invalidated

if the equipment is used in commercial, trade or industrial applications or for other equivalent activities. The

following are also excluded from our guarantee: compensation for transport damage, damage caused by

failure to comply with the installation/assembly instructions or damage caused by unprofessional

installation, failure to comply with the operating instructions (e.g. connection to the wrong mains voltage or

current type), misuse or inappropriate use (such as overloading of the device or use of non-approved tools

or accessories), failure to comply with the maintenance and safety regulations, ingress of foreign bodies

into the device (e.g. sand, stones or dust), effects of force or external influences (e.g. damage caused by

the device being dropped) and normal wear resulting from proper operation of the device.

This applies in

particular to rechargeable batteries for which we nevertheless issue a guarantee period of 12 months.

The guarantee is rendered null and void if any attempt is made to tamper with the device.

3. The guarantee is valid for a period of 3 years starting from the purchase date of the device. Guarantee

claims should be submitted before the end of the guarantee period within two weeks of the defect being

noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee

period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases,

the work performed or parts fitted will not result in an extension of the guarantee period, and no new

guarantee will become active for the work performed or parts fitted. This also applies when an on-site

service is used.

4. In order to assert your guarantee claim, please send your defective device postage-free to the address

shown below. Please enclose either the original or a copy of your sales receipt or another dated proof of

purchase. Please keep your sales receipt in a safe place, as it is your proof of purchase. It would help us if

you could describe the nature of the problem in as much detail as possible. If the defect is covered by our

guarantee then your device will either be repaired immediately and returned to you, or we will send you a

new device.

Of course, we are also happy offer a chargeable repair service for any defects which are not covered by the

scope of this guarantee or for units which are no longer covered. To take advantage of this service, please send

the device to our service address.

Anleitung_LB4_4010403:_ 24.02.2011 10:59 Uhr Seite 17

18

HU

Tartalomjegyzék: Oldal

1. Bevezetés ..............................................................................20

2. Biztonsági utasítások .............................................................20-22

3. A készülék leírása ..................................................................22

4. Rendeltetésszerűi használat ..................................................23

5. Technikai adatok ....................................................................23

6. Beüzemeltetés előtt ................................................................24

7. Összeszerelés és beüzemeltetés ...........................................24-25

8. A hálózati csatlakozóvezetéknek a kicserélése ......................25

9. Tisztítás, karbantartás, tárolás,

pótalkatrészmegrendelés és szállítás .....................................25-27

10. Megsemmisítés és újrahasznosítás ........................................27

11. Lehetséges kiesési okok ........................................................28

12. Konformkijelentés ..................................................................29

13. Garanciaokmány ....................................................................30

A termékek dokumentációjának és a

kisérőpapírjainak az utánnyomtatása vagy

egyébb sokszorosítása, kivonatosan is csak az

ISC GmbH kihangsúlyozott beleegyezésével

engedélyezett.

Technikai változtatások jogát fenntartva

Anleitung_LB4_4010403:_ 24.02.2011 10:59 Uhr Seite 18

19

HU

Kiegészítő biztonsági utasítások

Figyelembe venni a használati utasítást!

Zajcsökkentő fülvédőt hordani!

Figyelmeztetés az elektromos feszültség elöl

Figyelmeztetés a forró részek elöl

Figyelem! Ne nyissa meg a csapot/nyomásszabályozót, mielőtt rácsatlakoztatta

volna a légtömlőt.





Figyelmeztetés! Az egység távirányított és figyelmeztetés nélkül megindulhat

Anleitung_LB4_4010403:_ 24.02.2011 10:59 Uhr Seite 19

20

HU

1. Bevezetés

 Figyelem!

A készülékek használatánál, a sérülések és a

károk megakadályozásának az érdekébe be

kell tartani egy pár biztonsági intézkedést.

Olvassa ezért ezt a használati utasítást

gondosan át. Őrizze ezeket jól meg, azért hogy

mindenkor a rendelkezésére álljanak az

információk. Ha más személyeknek átadná a

készüléket, akkor kérjük kézbesítse ki vele

együtt ezt a használati utasítást is. Nem

vállalunk felelőséget olyan balesetekért vagy

károkért, amelyek ennek az utasításnak és a

biztonsági utasításoknak a figyelmen kívül

hagyásából keletkeznek.

2. Biztonsági utasítások

 FIGYELMEZTETÉS

Olvasson minden biztonsági utalást és

utasítást el. A biztonsági utalások és

utasítások betartásán belüli mulasztások

következménye áramcsapás, tűz és/vagy

nehéz sérülések lehetnek.

Őrizze meg a biztonsági utalásokat és

utasításokat a jövőre nézve.

2.1 Biztonsági utasítások

 Figyelem! Ennek a kompresszornak a

használatánál, áram ütés, sérülések és

tűzveszély elleni védelem szempontjából,

figyelembe kell venni a következő alapvető

biztonsági intézkedéseket. Olvassa és

vegye figyelembe ezeket az utasításokat,

mielőtt használná a készüléket.

■ Tartsa a munkakörét rendben

Rendetlenség a munkakörön belül balesetet

idéz elő.

■ Vegye a környezeti befolyásokat

figyelembe

Ne tegye ki a kompresszort esőnek. Ne

használja a kompresszort nedves vagy

vizes környezetben. Veszély az

áramcsapás által!

Gondoskodjon jó megvilágításról.

Ne használja a kompresszort gyúlékony

folyadékok vagy gázok közelében.

Robbanásveszély!

■ Óvja magát az áramütés elöl

Kerülje el a földelt részekkel, mint például

csövekkel, fűtőtestekkel, tűzhelyekkel,

hűtőszekrényekkel való testi érintkezést.

■ Tartsa a gyerekeket távol!

Ne engedje meg más személyeknek, hogy

megérintsék a kompresszort vagy a kábelt,

tartsa őket a munkakörétől távol.

■ Tárolja biztonságosan a kompresszort

A nem használt kompresszort egy száraz,

lezárt teremben és a gyerekek számára

hozzáférhetetlenül kell tárolni.

■ Ne terhelje túl a kompresszort

Jobban és biztonságosabban dolgozik a

megadott teljesítményi körben.

■ Viseljen megfelelő munkaruhát

Ne viseljen bő ruhát vagy ékszert. Ezeket

elkaphatják a mozgó részek. A szabadban

történö munkálatoknál gumikesztyű és

tapadós lábbeli ajánlatos. Hosszú hajnál

viseljen hajhálót. Sérülés veszélye!

■ Ne használja fel olyan célokra a kábelt,

amelyekre az nincs elölátva

Ne húzza a kompresszort a kábelnál fogva,

és ne használja fel a csatlakozó dugó

kihúzására a fali dugaszoló aljzatból. Óvja a

kábelt hőségtől, olajtól és éles szélektől.

Megsérülhet a kábel/csatlakozó dugó.

■ Ápolja gondosan a kompresszort

Tartsa a kompresszort tisztán azért, hogy jól

és biztosan tudjon dolgozni. Tartsa be a

karbantartási előírásokat. Ellenőrizze le

rendszeresen a csatlakozási vezetéket és a

kábelját, és sérülés esetén cseréltesse ki

azt egy elismert szakember által.

Ellenőrizze le rendszeresen a hosszabbító

kábelt és sérülés esetén cserélje ki.

■ Húzza ki a hálózati csatlakozót

Nemhasználat esetén, karbantartás előtt.

■ Kerülje el az akaratlan indulást

Bizonyosodjon meg róla, hogy a kapcsoló a

hálózatba való bedugáskor ki van

kapcsolva.

■ Hosszabbító kábel a szabadban

A szabadban csakis arra engedélyezett és

megfelelően megjelölt hosszabbító kábelt

használjon.

Anleitung_LB4_4010403:_ 24.02.2011 10:59 Uhr Seite 20

Stránka sa načítava ...

Parkside PKO 270 B2 Operation and Safety Notes

Parkside PKO 270 B2 Operation and Safety Notes

V iných jazykoch

Súvisiace články

Ďalšie dokumenty