Parkside PKO 270 A1 Operation and Safety Notes

IAN 89564

K

COMPRESSOR

Operation and Safety Notes

Original operating instructions

N

KOMPRESSZOR

Kezelési és biztonsági utalások

Eredeti használati utasítás

V

KOMPRESOR

Navodila za upravljanje in varnostna opozorila

Originalna navodila za uporabo

D

KOMPRESOR

Pokyny pro obsluhu a bezpečnostní pokyny

Originální návod k obsluze

W

KOMPRESOR

Pokyny pre obsluhu a bezpečnostné pokyny

Originálny návod na obsluhu

T

KOMPRESOR

Wskazówki dotyczące obsługi i bezpieczeństwa

Instrukcją oryginalną

N V

D W T

COMPRESSOR PKO 270 A1

F A C

KOMPRESSOR

Bedienungs- und Sicherheitshinweise / Originalbetriebsanleitung

Anleitung_4010363_LB4.indb 1Anleitung_4010363_LB4.indb 1 17.01.13 13:0217.01.13 13:02

- 2 -

K

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of

the device.

N

Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik

funkcióját.

V

Pred branjem stran s slikami odprite navzven in se nato seznanite z vsemi funkcijami naprave.

D

Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.

W

Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

T

Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z

wszystkimi funkcjami urządzenia.

F A C

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit

allen Funktionen des Gerätes vertraut.

GB Operation and Safety Notes Page 6

HU Kezelési és biztonsági utalások Oldal 19

SI Navodila za upravljanje in varnostna opozorila Stran 33

CZ Pokyny pro obsluhu a bezpečnostní pokyny Strana 45

SK Pokyny pre obsluhu a bezpečnostné pokyny Strana 57

PL Wskazówki dotyczące obsługi i bezpieczeństwa Strona 70

DE/AT/CH Bedienungs- und Sicherheitshinweise Seite 84

Anleitung_4010363_LB4.indb 2Anleitung_4010363_LB4.indb 2 17.01.13 13:0317.01.13 13:03

- 3 -

1

2

11

9 810

12

1

2

3

4

5

6

7

13

16

17

3

18

19

20

4

15

G H

14

Anleitung_4010363_LB4.indb 3Anleitung_4010363_LB4.indb 3 17.01.13 13:0317.01.13 13:03

- 4 -

4

11

5

24

10

8 9

10

A

6

24

8

7

11 23 24 25 26 8 26 23 24

23 24 1510

22

11

22

26

23

26

25,26

B

15

26

23

Anleitung_4010363_LB4.indb 4Anleitung_4010363_LB4.indb 4 17.01.13 13:0317.01.13 13:03

- 5 -

10 11

18

12 13

16

21

max

min

D E C

C D F

Anleitung_4010363_LB4.indb 5Anleitung_4010363_LB4.indb 5 17.01.13 13:0317.01.13 13:03

GB

- 6 -

Table of contents

The reprinting or reproduction by any other means, in whole or in part, of documentation and papers

accompanying products is permitted only with the express consent of the iSC GmbH.

Subject to technical changes

1. Introduction .................................................................................................................................................. 8

2. Safety regulations ....................................................................................................................................... 8

3. Layout and items supplied ........................................................................................................................10

4. Proper use ...................................................................................................................................................11

5. Technical data ............................................................................................................................................11

6. Before starting the equipment ...................................................................................................................11

7. Assembly and starting .............................................................................................................................. 12

8. Replacing the power cable ...................................................................................................................... 12

9. Cleaning, maintenance, ordering of spare parts and storage .............................................................. 13

10. Disposal and recycling .............................................................................................................................14

11. Possible causes of failure .......................................................................................................................... 16

12. Declaration of conformity .........................................................................................................................17

13. Warranty certiﬁ cate .................................................................................................................................. 18

Anleitung_4010363_LB4.indb 6Anleitung_4010363_LB4.indb 6 17.01.13 13:0317.01.13 13:03

GB

- 7 -

Caution - Read the operating instructions to reduce the risk of inquiry

Wear ear-muffs. The impact of noise can cause damage to hearing.

Beware of electrical voltage!

Beware of hot parts!

Warning! The equipment is remote-controlled and may start-up without warning.

Caution! Before using for the ﬁ rst time, check the oil level and replace the oil sealing plug!

Anleitung_4010363_LB4.indb 7Anleitung_4010363_LB4.indb 7 17.01.13 13:0317.01.13 13:03

GB

- 8 -

1. Introduction

Congratulations on your new purchase.

You have decided in favor of a high-quality pro-

duct. The operating instructions are a part of this

product. They contain information of importance

for your safety, for the use of the product and for

its disposal. Before you use the product, acquaint

yourself with all the information concerning its

operation and safety. Use the product only as

described and only for the listed areas of applica-

tion. If you hand on the product to other people,

give them all the documentation as well.

2. Safet y regulations

 Caution!

Read all safety regulations and instruc-

tions.

Any errors made in following the safety regu-

lations and instructions may result in an electric

shock, ﬁ re and/or serious injury.

Keep all safety regulations and instruc-

tions in a safe place for future use.

2.1 Safety information

 Important! The following basic safety

actions must be taken when using this

compressor in order to protect the user

from electric shocks and the risk of injury

and ﬁ re. Read and follow these instruc-

tions before using the equipment.

•

Keep your work area tidy

Untidy work areas can result in accidents.

•

Check the ambient conditions

Do not expose the compressor to rain. Never

use the compressor in damp or wet locations.

There is a risk of electric shock! Provide good

lighting. Do not use the compressor near

flammable liquids or gases. There is a risk of

explosion!

•

Protect yourself against electric

shocks

Avoid bodily contact with earthed parts, e.g.

pipes, radiators, cookers and refrigerators.

•

Keep children away!

Do not allow other persons to touch the com-

pressor or cable, keep them away from your

work area.

•

Keep your compressor in a safe place

When unused, the compressor must be stored

in a dry, locked room out of children’s reach.

•

Do not overload your compressor

It will run better and safer within its quoted

capacity range.

•

Wear suitable work clothes

Never wear loose fitting clothes or jewellery.

They may get caught in moving parts. Rubber

gloves and non-slip shoes are recommended

when working outdoors. Wear a hair net if

you have long hair. Risk of injury!

•

Do not use the cable for purposes

other than that for which it is designed

Do not carry the compressor by its cable and

do not use the cable to pull the plug out of the

socket. Protect the cable from heat, oil and

sharp edges. The cable/plug could become

damaged.

•

Take care of your compressor

Keep your compressor clean in order to work

well and safely. Follow the maintenance inst-

ructions. Check the power plug and cable on

a regular basis and have them replaced by

an authorized specialist if they are damaged.

Check the extension cable regularly and re-

place it if damaged.

•

Pull out the power plug

When not in use and before carrying out any

maintenance work.

•

Avoid unintentional starting

Make sure that the switch is turned off when

connecting to the power supply.

•

When using an extension cable out-

doors

Check that it is approved for outdoor duty

and is marked accordingly.

•

Be alert at all times

Watch what you are doing. Use common sen-

se when working. Never use the compressor

when you are distracted.

•

Check your compressor for damage

Before using the compressor again, carefully

check the safety devices and any slightly da-

Anleitung_4010363_LB4.indb 8Anleitung_4010363_LB4.indb 8 17.01.13 13:0317.01.13 13:03

GB

- 9 -

maged parts to ensure that they are in good

working order. Check that the moving parts

are working correctly, that they do not jam,

and that no parts are damaged. Make sure

that all parts are fitted correctly to ensure that

the equipment remains safe to use. Unless

otherwise stated in the operating instructions,

damaged guards and parts have to be re-

paired or replaced by a customer service

workshop. Damaged switches have to be

replaced by a customer service workshop.

Never use an electric power tool with a switch

that cannot be turned on and off.

•

Important!

For your own safety you must only use the

accessories and additional units listed in the

operating instructions or recommended or

specified by the manufacturer. The use of

mounted tools or accessories other than those

recommended in the operating instructions

or catalog may place your personal safety

at risk.

•

Leave all repairs to a qualified electri-

cian

Repairs must be left strictly to qualified electri-

cians or the user might suffer an accident.

•

Noise

Wear ear muffs when you use the compressor.

•

Replacing the power cable

To prevent hazards, leave the replacement of

damaged power cables strictly to the manu-

facturer or a qualified electrician. There is a

risk of electric shock!

•

Inflating tires

Directly after inflating tires, check the pressure

with a suitable pressure gauge, for example

at your filling station.

•

Roadworthy compressors for building

site operations

Make sure that all lines and fittings are sui-

table for the maximum permissible operating

pressure of the compressor.

•

Place of installation

Set up the compressor on an even surface.

2.2 Safety instructions for working with

compressed air and blasting guns

•

The compressor pump and lines can become

very hot during operation. Touching these

parts will burn you.

•

The air which is sucked in by the compressor

must be kept free of impurities that could

cause fires or explosions in the compressor

pump.

•

When releasing the hose coupling, hold the

hose coupling piece with your hand. This way,

you can protect yourself against injury from

the rebounding hose.

•

Wear safety goggles when working with the

blow-out pistol. Foreign bodies or blown off

parts can easily cause injuries.

•

Do not blow at people with the blow-out

pistol and do not clean clothes while being

worn. Risk of injury!

2.3. Safety information for paint spray-

ing

•

Do not process any paints or solvents with a

flash point below 55° C. There is a risk of ex-

plosion!

•

Do not heat up paints or solvents. There is a

risk of explosion!

•

If hazardous liquids are processed, wear pro-

tective filter units (face guards). Also, adhere

to the safety information provided by the ma-

nufacturers of such liquids.

•

The details and designations of the Ordi-

nance on Hazardous Substances, which

are displayed on the outer packaging of the

processed material, must be observed. Addi-

tional protective measures are to be underta-

ken if necessary, particularly the wearing of

suitable clothing and masks.

•

Do not smoke during the spraying process

and/or in the work area. There is a risk of ex-

plosion! Paint vapors are easily combustible.

•

Never set up or operate the equipment in the

vicinity of a fire place, open lights or sparking

machines.

•

Do not store or eat food and drink in the work

area. Paint vapors are harmful to your health.

•

The work area must exceed 30 m

3

and suf-

ficient ventilation must be ensured during

Anleitung_4010363_LB4.indb 9Anleitung_4010363_LB4.indb 9 17.01.13 13:0317.01.13 13:03

GB

- 10 -

spraying and drying. Do not spray against the

wind. Always adhere to the regulations of the

local police authority when spraying combus-

tible or hazardous materials.

•

Do not process media such as white spirit,

butyl alcohol and methylene chloride with the

PVC pressure hose. These media will destroy

the pressure hose.

2.4 Operating pressure vessels

•

You must keep your pressure vessel in good

working order, operate the vessel correctly,

monitor the vessel, carry out necessary main-

tenance and repair work immediately and

meet the relevant safety precautions.

•

The supervisory authority may enforce essenti-

al control measures in individual cases.

•

A pressure vessel is not allowed to be used if

it has faults or deficiencies that can endanger

workers or third parties.

•

Check the pressure vessel for signs of rust

and damage each time before using. Do not

use the compressor with a damaged or rusty

pressure vessel. If you discover any damage,

then please contact the customer service

workshop.

Do not lose these safety instructions

3. Layout and items supplied

3.1 Layout

1. Transport handle

2. Pressure switch

3. Pressure regulator

4. Quick-lock coupling

(regulated compressed air)

5. Pressure gauge

(for reading the preset vessel pressure)

6. Pressure gauge

(for reading the vessel pressure)

7. Pressure vessel

8. Supporting foot

9. Drain plug for condensation water

10. Hub cap

11. Wheel

12. Oil drain plug

13. Compressor pump

14. Compressed air hose

15. Air ﬁ lter

16. Oil sealing plug

17. ON/OFF switch

18. Oil – level window

19. Safety valve

20. Quick-lock coupling (unregulated com-

pressed air)

21. Oil ﬁ ller opening

22. Nut (self-locking)

23. Spring washer

24. Nut

25. Screw

26. Washer

3.2 Items supplied

•

Open the packaging and take out the equip-

ment with care.

•

Remove the packaging material and any

packaging and/or transportation braces (if

available).

•

Check to see if all items are supplied.

•

Inspect the equipment and accessories for

transport damage.

•

If possible, please keep the packaging until

the end of the guarantee period.

Important!

The equipment and packaging material

are not toys. Do not let children play with

plastic bags, foils or small parts. There is

a danger of swallowing or suffocating!

Anleitung_4010363_LB4.indb 10Anleitung_4010363_LB4.indb 10 17.01.13 13:0317.01.13 13:03

GB

- 11 -

4. Proper use

The compressor is designed to generate com-

pressed air for compressed-air driven tools which

can be driven with an air volume of up to approx.

270 l/min (e.g. tire inﬂ ator, blow-out pistol and

paint spray gun). Due to the limited air output it is

not possible to use the compressor to drive tools

with very high air consumption (for example or-

bital sanders, rod grinders and hammer screwdri-

vers).

The equipment is to be used only for its prescribed

purpose. Any other use is deemed to be a case of

misuse. The user / operator and not the manufac-

turer will be liable for any damage or injuries of

any kind caused as a result of this.

Please note that our equipment has not been de-

signed for use in commercial, trade or industrial

applications. Our warranty will be voided if the

machine is used in commercial, trade or industrial

businesses or for equivalent purposes.

5. Technical data

Mains connection: .........................230 V ~ 50 Hz

Motor rating kW: ........................................1.8 kW

Operating mode: ................................................S1

Compressor speed min

-1

: .............................. 2850

Operating pressure bar: ..............................max. 8

Pressure vessel capacity (in liters): .....................24

Theoretical intake capacity (l/min): . approx. 270

Sound power level L

WA

in dB: ............................94

K

WA

uncertainty: ...............................................4 dB

Protection type: ................................................IP20

Weight of the unit in kg: ......................................26

Oil (15W 40): ..................................................0.3 l

The noise emission values were measured in ac-

cordance with EN ISO 2151.

6. Before starting the

equipment

Before you connect the equipment to the mains

supply make sure that the data on the rating plate

are identical to the mains data.

•

Check the equipment for damage which may

have occurred in transit. Report any damage

immediately to the transport company which

was used to deliver the compressor.

•

Install the compressor near the point of con-

sumption.

•

Avoid long air lines and supply lines (extensi-

on cables).

•

Make sure that the intake air is dry and dust-

free.

•

Do not install the compressor in a damp or

wet room.

•

The compressor may only be used in suitable

rooms (with good ventilation and an ambient

temperature from +5 °C to 40 °C). There must

be no dust, acids, vapors, explosive gases or

inflammable gases in the room.

•

The compressor is designed to be used in dry

rooms. It is prohibited to use the compressor in

areas where work is conducted with sprayed

water.

•

The oil level in the compressor pump has to

be checked before putting the equipment into

operation (see 9.4).

Anleitung_4010363_LB4.indb 11Anleitung_4010363_LB4.indb 11 17.01.13 13:0317.01.13 13:03

GB

- 12 -

7. Assembly and starting

 Important!

Remove the transportation braces (bet-

ween the compressor pump and clad-

ding, see Fig. 7) prior to initial start-up.

If the transportation braces are not re-

moved, heat can build up and cause the

compressor to ignite.

 Important!

You must fully assemble the appliance

before using it for the ﬁ rst time!

You will require the following tools for assembly

and installation:

2 x open-ended wrench size 13 mm (not inclu-

ded)

7.1 Fitting the wheels (11)

Fit the supplied wheels as shown in Figure 5.

7.2 Fitting the supporting foot (8)

Fit the supplied supporting foot as shown in Figure

6.

7.3 Fitting the air ﬁ lter (15)

Remove the transportation stop (B) and screw the

air ﬁ lter (15) to the equipment. (Fig. 7, 8).

7.4 Changing the transportation cover (A)

Remove the transportation cover from the oil ﬁ ller

opening (21) and insert the supplied oil sealing

plug (16) into the oil ﬁ ller opening. (Fig. 9, 10.)

7.5 Mains connection

•

The compressor is equipped with a mains

cable with shock-proof plug. This can be

connected to any 230V ~ 50 Hz shock-proof

socket which is protected by a 16 A fuse.

•

Before you use the machine, make sure that

the mains voltage is the same as the operating

voltage (see the rating plate).

•

Long supply cables, extensions, cable reels

etc. cause a drop in voltage and can impede

motor start-up.

•

At low temperatures below +5°C, sluggish-

ness may make starting difficult or impossible.

7.6 ON/OFF switch (Fig. 2)

Pull the ON/OFF switch (17) upwards to switch

on the compressor. To switch off the compressor,

press the ON/OFF switch down.

7.7 Setting the pressure (Fig. 1-3)

•

Use the pressure regulator (3) to set the pres-

sure on the pressure gauge (5).

•

The set pressure can be drawn from the quick-

lock coupling (4).

•

The vessel pressure can be read off the pres-

sure gauge (6).

•

The vessel pressure is drawn from the quick-

lock coupling (20).

7.8 Setting the pressure switch (Fig. 1)

The pressure switch (2) is set at the factory.

Cut-in pressure approx. 6 bar

Cut-out pressure approx. 8 bar

7.9 Fitting the compressed air hose

(Fig. 1, 3)

Use the compressed air hose (14) if you intend

to carry out work at a greater distance from the

compressor. To do so, connect the nipple (H)

on the compressed air hose to one of the quick-

release couplings (4, 20). Then attach the com-

pressed air tool to the quick-release coupling (G)

on the compressed air hose.

8. Replacing the power cable

If the power cable for this equipment is damaged,

it must be replaced by the manufacturer or its

after-sales service or similarly trained personnel to

avoid danger.

Anleitung_4010363_LB4.indb 12Anleitung_4010363_LB4.indb 12 17.01.13 13:0317.01.13 13:03

GB

- 13 -

9. Cleaning, maintenance,

ordering of spare parts and

storage

 Important!

Pull out the power plug before doing any

cleaning and maintenance work on the

equipment. Risk of injury from electric

shock!

 Important!

Wait until the equipment has cooled

down completely! Risk of burns!

 Important!

Always depressurize the equipment be-

fore carrying out any cleaning and main-

tenance work! Risk of injury!

9.1 Cleaning

•

Keep the equipment free of dirt and dust as

far as possible. Wipe the equipment with a

clean cloth or blow it down with compressed

air at low pressure.

•

We recommend that you clean the equipment

immediately after you use it.

•

Clean the equipment regularly with a damp

cloth and some soft soap. Do not use cleaning

agents or solvents; these may be aggressive

to the plastic parts in the equipment. Ensure

that no water can get into the interior of the

equipment.

•

You must disconnect the hose and any

spraying tools from the compressor before

cleaning. Do not clean the compressor with

water, solvents or the like.

9.2 Maintenance work on the pressure

vessel (Fig. 1)

Important! To ensure a long service life of the

pressure vessel (7), drain off the condensed water

by opening the drain valve (9) each time after

using. Release the vessel pressure ﬁ rst (see 9.7.1).

Open the drain screw by turning counter-clock-

wise (looking at the screw from the bottom of the

compressor) so that all the condensed water can

run out of the pressure vessel. Then close the drain

screw again (turn it clockwise). Check the pressure

vessel for signs of rust and damage each time

before using. Do not use the compressor with a

damaged or rusty pressure vessel. If you discover

any damage, then please contact the customer

service workshop.

 Important!

The condensed water from the pressure

vessel will contain residual oil. Dispose

of the condensed water in an environ-

mentally compatible manner at a suitable

collection point.

9.3 Safety valve (Figure 3)

The safety valve (19) has been set for the highest

permitted pressure of the pressure vessel. It is

prohibited to adjust the safety valve or remove its

seal. Actuate the safety valve from time to time to

ensure that it works when required. Pull the ring

with sufﬁ cient force until you can hear the com-

pressed air being released. Then release the ring

again.

9.4 Checking the oil level at regular inter-

vals (Figure 11)

Place the compressor on a level and straight sur-

face. The oil level must be between the MAX and

MIN marks on the oil level window (Fig. 18). Oil

change: we recommend SAE 15W 40 or equiva-

lent. The original oil ﬁ lling must be changed after

100 hours in operation; thereafter the oil must be

drained and replaced with new oil after every

500 hours in operation.

9.5 Changing the oil (Figure 1,10, 11)

Switch off the engine and pull the mains plug out

of the socket. After releasing any air pressure you

can unscrew the oil drain plug (12) from the com-

pressor pump (13). To prevent the oil from running

out in an uncontrolled manner, hold a small metal

chute under the opening and collect the oil in a

vessel. If the oil does not drain out completely, we

recommend tilting the compressor slightly. When

the oil has drained out, reﬁ t the oil drain plug (12).

Anleitung_4010363_LB4.indb 13Anleitung_4010363_LB4.indb 13 17.01.13 13:0317.01.13 13:03

GB

- 14 -

Dispose of the old oil at a drop-off point

for old oil.

To ﬁ ll in the correct quantity of oil, make sure that

the compressor stands on an even surface. Fill

new oil through the oil ﬁ ller opening (21) until it

comes up to the maximum level. This is marked

with a red dot on the oil level window (18) (Figure

11). Do not exceed the maximum ﬁ lling quantity.

Overﬁ lling the equipment may result in damage.

Reinsert the oil sealing plug (16) into the oil ﬁ ller

opening (21).

9.6 Cleaning the intake ﬁ lter

(Fig. 3, 12, 13)

The intake ﬁ lter prevents dust and dirt being

drawn in. It is essential to clean this ﬁ lter after

at least every 300 hours in service. A clogged

intake ﬁ lter will decrease the compressor’s perfor-

mance dramatically. Open the thumb screw (E) to

the remove the intake ﬁ lter. Then pull off the ﬁ lter

cover (C). Now you can remove the air ﬁ lter (F)

and the ﬁ lter housing (D). Carefully tap out the air

ﬁ lter, ﬁ lter cover and ﬁ lter housing. Then blow out

these parts with compressed air (approx. 3 bar)

and reinstall in reverse order.

9.7 Storage

 Important!

Pull out the mains plug and ventilate the

equipment and all connected pneuma-

tic tools. Switch off the compressor and

make sure that it is secured in such a way

that it cannot be started up again by any

unauthorized person.

 Important!

Store the compressor only in a dry lo-

cation which is not accessible to unau-

thorized persons. Always store upright,

never tilted! Oil may leak out!

9.7.1 Releasing excess pressure

Release the excess pressure by switching off the

compressor and using the compressed air which

is still left in the pressure vessel, e.g. with a com-

pressed air tool running in idle mode or with a

blow-out pistol.

9.8 Ordering replacement parts:

Please quote the following data when ordering

replacement parts:

•

Type of machine

•

Article number of the machine

•

Identification number of the machine

For our latest prices and information please go to

www.isc-gmbh.info

10. Disposal and recycling

The unit is supplied in packaging to prevent its

being damaged in transit. This packaging is raw

material and can therefore be reused or can be

returned to the raw material system.

The unit and its accessories are made of various

types of material, such as metal and plastic. De-

fective components must be disposed of as spe-

cial waste. Ask your dealer or your local council.

Anleitung_4010363_LB4.indb 14Anleitung_4010363_LB4.indb 14 17.01.13 13:0317.01.13 13:03

GB

- 15 -

For EU countries only

Never place any electric power tools in your

household refuse.

To comply with European Directive 2002/96/EC

concerning old electric and electronic equipment

and its implementation in national laws, old elec-

tric power tools have to be separated from other

waste and disposed of in an environment-friendly

fashion, e.g. by taking to a recycling depot.

Recycling alternative to the return request:

As an alternative to returning the equipment to the

manufacturer, the owner of the electrical equip-

ment must make sure that the equipment is proper-

ly disposed of if he no longer wants to keep the

equipment. The old equipment can be returned to

a suitable collection point that will dispose of the

equipment in accordance with the national recyc-

ling and waste disposal regulations. This does not

apply to any accessories or aids without electrical

components supplied with the old equipment.

Anleitung_4010363_LB4.indb 15Anleitung_4010363_LB4.indb 15 17.01.13 13:0317.01.13 13:03

GB

- 16 -

11. Possible causes of failure

Problem Cause Solution

The compressor

does not start.

1. No supply voltage.

2. Insufﬁ cient supply voltage.

3. Outside temperature is too low.

4. Motor is overheated.

1. Check the supply voltage, the pow-

er plug and the socket-outlet.

2. Make sure that the extension cable

is not too long. Use an extension

cable with large enough wires.

3. Never operate with an outside tem-

perature of below +5° C.

4. Allow the motor to cool down. If

necessary, remedy the cause of the

overheating.

The compressor

starts but there is no

pressure.

1. The non-return valve leaks.

2. The seals are damaged.

3. The drain plug for condensation

water (9) leaks.

1. Have a service center replace the

non-return valve.

2. Check the seals and have any da-

maged seals replaced by a service

center.

3. Tighten the screw by hand. Check

the seal on the screw and replace if

necessary.

The compressor

starts, pressure is

shown on the pres-

sure gauge, but the

tools do not start.

1. The hose connections have a leak.

2. A quick-lock coupling has a leak.

3. Insufﬁ cient pressure set on the pres-

sure regulator (3).

1. Check the compressed air hose and

tools and replace if necessary.

2. Check the quick-lock coupling and

replace if necessary.

3. Increase the set pressure with the

pressure regulator.

Anleitung_4010363_LB4.indb 16Anleitung_4010363_LB4.indb 16 17.01.13 13:0317.01.13 13:03

GB

- 17 -

12. Declaration of conformity

Yu Feng Quing/Product-ManagementWeichselgartner/General-Manager

D erklärt folgende Konformität gemäß EU-Richtlinie und

Normen für Artikel

GB explains the following conformity according to EU directi-

ves and norms for the following product

F déclare la conformité suivante selon la directive CE et les

normes concernant l’article

I dichiara la seguente conformità secondo la direttiva UE e

le norme per l’articolo

NL verklaart de volgende overeenstemming conform EU

richtlijn en normen voor het product

E declara la siguiente conformidad a tenor de la directiva y

normas de la UE para el artículo

P declara a seguinte conformidade, de acordo com a

directiva CE e normas para o artigo

DK attesterer følgende overensstemmelse i medfør af

EU-direktiv samt standarder for artikel

S förklarar följande överensstämmelse enl. EU-direktiv och

standarder för artikeln

FIN vakuuttaa, että tuote täyttää EU-direktiivin ja standardien

vaatimukset

EE tõendab toote vastavust EL direktiivile ja standarditele

CZ vydává následující prohlášení o shodě podle směrnice EU

a norem pro výrobek

SLO potrjuje sledečo skladnost s smernico EU in standardi za

izdelek

SK vydáva nasledujúce prehlásenie o zhode podľa smernice

EÚ a noriem pre výrobok

H a cikkekhez az EU-irányvonal és Normák szerint a

következő konformitást jelenti ki

PL deklaruje zgodność wymienionego poniżej artykułu z

następującymi normami na podstawie dyrektywy WE.

BG декларира съответното съответствие съгласно

Директива на ЕС и норми за артикул

LV paskaidro šādu atbilstību ES direktīvai un standartiem

LT apibūdina šį atitikimą EU reikalavimams ir prekės normoms

RO declară următoarea conformitate conform directivei UE şi

normelor pentru articolul

GR δηλώνει την ακόλουθη συμμόρφωση σύμφωνα με την

Οδηγία ΕΚ και τα πρότυπα για το προϊόν

HR potvrđuje sljedeću usklađenost prema smjernicama EU i

normama za artikl

Izjava o sukladnosti za ovaj proizvod dostupna je na

internet stranici www.lidl.hr.

BIH potvrđuje sljedeću usklađenost prema smjernicama EU i

normama za artikl

RS potvrđuje sledeću usklađenost prema smernicama EZ i

normama za artikal

RUS следующим удостоверяется, что следующие продукты

соответствуют директивам и нормам ЕС

UKR проголошує про зазначену нижче відповідність виробу

директивам та стандартам ЄС на виріб

MK ја изјавува следната сообрзност согласно

ЕУ-директивата и нормите за артикли

TR Ürünü ile ilgili AB direktiﬂ eri ve normları gereğince aşağıda

açıklanan uygunluğu belirtir

N erklærer følgende samsvar i henhold til EU-direktivet og

standarder for artikkel

IS Lýsir uppfyllingu EU-reglna og annarra staðla vöru

Konformitätserklärung

Kompressor PKO 270 A1 (Parkside)

X

87/404/EC_2009/105/EC

2005/32/EC_2009/125/EC

2006/95/EC

2006/28/EC

X

2004/108/EC

2004/22/EC

1999/5/EC

X

97/23/EC

90/396/EC_2009/142/EC

89/686/EC_96/58/EC

X

2011/65/EC

X

2006/42/EC

Annex IV

Notiﬁ ed Body:

Notiﬁ ed Body No.:

Reg. No.:

X

2000/14/EC_2005/88/EC

Annex V

X

Annex VI

Noise measured: L

WA

= 90 dB (A); guaranteed L

WA

= 94 dB (A)

P = 1.8 KW; L/Ø = cm

Notiﬁ ed Body: TÜV Rheinland

2004/26/EC

Emission No.:

Standard references: EN 1012-1; EN 60204-1;

EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3

Landau/Isar, den 19.12.2012

First CE: 12 Archive-File/Record: NAPR007096

Art.-No.: 40.103.63 I.-No.: 11032 Documents registrar: Siegfried Roider

Subject to change without notice Wiesenweg 22, D-94405 Landau/Isar

Einhell Germany AG · Wiesenweg 22 · D-94405 Landau/Isar

Anleitung_4010363_LB4.indb 17Anleitung_4010363_LB4.indb 17 17.01.13 13:0317.01.13 13:03

GB

13. Warrant y cer tiﬁ cate

Dear Customer,

All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event

that your device develops a fault, please contact our service department at the address shown on this guarantee card.

Of course, if you would prefer to call us then we are also happy to offer our assistance under the service number prin-

ted below. Please note the following terms under which guarantee claims can be made:

1. These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights. We do

not charge you for this guarantee.

2. Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the rec-

tiﬁ cation of these defects or replacement of the device. Please note that our devices have not been designed for

use in commercial, trade or industrial applications. Consequently, the guarantee is invalidated if the equipment

is used in commercial, trade or industrial applications or for other equivalent activities. The following are also

excluded from our guarantee: compensation for transport damage, damage caused by failure to comply with

the installation/assembly instructions or damage caused by unprofessional installation, failure to comply with the

operating instructions (e.g. connection to the wrong mains voltage or current type), misuse or inappropriate use

(such as overloading of the device or use of non-approved tools or accessories), failure to comply with the main-

tenance and safety regulations, ingress of foreign bodies into the device (e.g. sand, stones or dust), effects of

force or external inﬂ uences (e.g. damage caused by the device being dropped) and normal wear resulting from

proper operation of the device. This applies in particular to rechargeable batteries for which we nevertheless

issue a guarantee period of 12 months. The guarantee is rendered null and void if any attempt is made to tamper

with the device.

3. The guarantee is valid for a period of 3 years starting from the purchase date of the device. Guarantee claims

should be submitted before the end of the guarantee period within two weeks of the defect being noticed. No

guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains

applicable to the device even if repairs are carried out or parts are replaced. In such cases, the work performed

or parts ﬁ tted will not result in an extension of the guarantee period, and no new guarantee will become active

for the work performed or parts ﬁ tted. This also applies when an on-site service is used.

4. In order to assert your guarantee claim, please send your defective device postage-free to the address shown

below. Please enclose either the original or a copy of your sales receipt or another dated proof of purchase.

Please keep your sales receipt in a safe place, as it is your proof of purchase. It would help us if you could de-

scribe the nature of the problem in as much detail as possible. If the defect is covered by our guarantee then your

device will either be repaired immediately and returned to you, or we will send you a new device.

Of course, we are also happy offer a chargeable repair service for any defects which are not covered by the scope

of this guarantee or for units which are no longer covered. To take advantage of this service, please send the device

to our service address.

- 18 -

IAN 89564

Anleitung_4010363_LB4.indb 18Anleitung_4010363_LB4.indb 18 17.01.13 13:0317.01.13 13:03

HU

- 19 -

Tartalomjegyzék

A termékek dokumentációjának és a kisérőpapírjainak az utánnyomtatása vagy egyébb sokszorosítása,

kivonatosan is csak az iSC GmbH kihangsúlyozott beleegyezésével engedélyezett.

Technikai változtatások jogát fenntartva

1. Bevezetés ................................................................................................................................................... 21

2. Biztonsági utasítások ................................................................................................................................ 21

3. A készülék leírása és a szállítás terjedelme ............................................................................................23

4. Rendeltetés szerinti használat .................................................................................................................24

5. Technikai adatok .......................................................................................................................................24

6. Beüzemeltetés előtt ...................................................................................................................................24

7. Összeszerelés és beüzemeltetés ..............................................................................................................25

8. A hálózati csatlakozóvezetéknek a kicserélése .....................................................................................26

9. Tisztítás, karbantartás, pótalkatrészmegrendelés és tárolás ................................................................26

10. Megsemmisítés és újrahasznosítás ..........................................................................................................27

12. Konformkijelentés ......................................................................................................................................30

13. Garanciaokmány .................................................................................................................................... 31

Anleitung_4010363_LB4.indb 19Anleitung_4010363_LB4.indb 19 17.01.13 13:0317.01.13 13:03