Sentiotec Qube Používateľská príručka

Version 03/21 Ident. no. QUBE-MA

INSTRUCTIONS FOR INSTALLATION AND USE

English

EN

DE

FR

IT

NL

SV

CS

SL

FI

Sauna heater

Qube

QUBE-090 / 1-028-940: Qube sauna heater 9.0 kW

QUBE-105 / 1-028-594: Qube sauna heater 10.5 kW

QUBE-120 / 1-029-871: Qube sauna heater 12.0 kW

QUBE-150 / 1-029-875: Qube sauna heater 15.0 kW

Table of Contents

1. About this instruction manual 4

2. Important information for your safety 5

2.1. Intended use 5

2.2. Safety information for the installer 5

2.3. Safety information for the user 7

3. Product description 8

3.1. Scope of delivery 8

3.2. Accessories 8

3.3. Product functions 8

4. Installation and connection 9

4.1. Installation location and sensor position 9

4.2. Safety distances 10

4.3. Adjusting the height 11

4.4. Connection diagram for 400 V 3N~ 12

4.5. Connection diagram for 230 V 1N~ 14

4.6. Wiring diagrams 15

4.7. Electrical connection 17

5. Commissioning 19

5.1. Filling the stone container 19

5.2.Heatingforthersttime 19

6. Operation 20

6.1. Operating the sauna heater 20

6.2. Infusion 20

EN

7. Maintenance 21

7.1. Extended periods of non-use 21

7.2. Cleaning the sauna heater 21

7.3. Changing the sauna stones 21

8. Disposal 22

9. Problem-solving by the installer 22

10. Technical data 23

Instructions for installation and use p. 4/24

1. About this instruction manual

Carefully read these instructions for installation and use, and keep them near

the sauna. This ensures that you can refer to information about your safety and

the operation at any time.

Symbols used for warning notices

In these instructions for installation and use, a warning notice located next to

an activity indicates that this activity poses a risk. Always observe the warning

notices. This prevents damage to property and injuries, which in the worst case

may be fatal.

The warning notices contain keywords, which have the following meanings:

DANGER!

Serious or fatal injury will occur if this warning notice is not observed.

WARNING!

Serious or fatal injury can occur if this warning notice is not observed.

CAUTION!

Minor injuries can occur if this warning notice is not observed.

ATTENTION!

This keyword is a warning that damage to property can occur.

Other symbols

This symbol indicates tips and useful information.

Do not cover Read the operating instructions

These installation and operating instructions can also be found in the

downloads section of our website: www.sentiotec.com/downloads.

EN

Instructions for installation and use p. 5/24

2. Important information for your safety

The Qube sauna heater has been produced in accordance with the

applicable safety rules and regulations. However, hazards may oc-

cur during use. Therefore adhere to the following safety information

andthespecicwarningnoticesintheindividualchapters.

2.1. Intended use

The Qube sauna heater is intended solely for heating sauna cab-

ins, in conjunction with a sauna control unit which does not include

a remote start function.

The Qube sauna heater can also be operated using a sauna control

unit with a remote start function, but only in conjunction with the

optionalcut-orockerswitch.

The Qube sauna heater can also be used in public saunas, but only

inconjunctionwiththeoptionalcut-orockerswitch.

Any use exceeding this scope is considered improper use. Improper

use can result in damage to the product, severe injuries or death.

2.2. Safety information for the installer

●Installing and connecting the sauna heater may only be performed

when the power supply is disconnected.

●Installationmayonlybeperformedbyaqualiedelectricianor

similarlyqualiedperson.

●A fully disconnecting all-pole isolating device compliant with

overvoltagecategoryIIImustbettedonsite.

●Always use silicone cables that are heat-resistant up to 150 °C

to connect the sauna heater.

Instructions for installation and use p. 6/24

●Only install one sauna heater in the cabin. The Qube sauna

heater must not be used together with other sauna heaters in

a sauna cabin.

●The roof and walls of the sauna cabin must be manufactured

from low-resin, untreated or thermally treated wood, e.g. Nordic

spruce,hemlock,pineorr,orfromlaminatedwoodenmateri-

als. If laminated wooden materials are used, make sure that the

adhesiveusedinthemdoesnotgiveoformaldehyde.Ifother

materials than wood are used in the sauna cabin, these materi-

als must be heat-resistant and corrosion-resistant and must not

causeanynegativeeectsonthehealthofthesaunausers.

●The height of the sauna cabin must be at least 2.0 m.

● Observethespecicationsonvolumesandonventilationofthe

sauna cabin in chapter 10. Technical data.

●When positioning the sauna heater, observe the minimum safety

distances (see chapter 4.2. Safety distances).

●Also comply with the regulations applicable at the installation

location.

●For your own safety, consult your supplier in the event of prob-

lemsthatarenotexplainedinsucientdetailintheinstallation

instructions.

EN

Instructions for installation and use p. 7/24

2.3. Safety information for the user

●The device must not be used by children under 8 years of age.

●The device may only be used by children over 8 years of age, by

persons with limited psychological, sensory or mental capabili-

ties or by persons with lack of experience/knowledge under the

following conditions:

– They are supervised.

– They have been shown how to use the device safely and

are aware of the hazards that could occur.

●Children must not play with the device.

●Children under 14 years of age may only clean the device if they

are supervised.

● Forhealthreasons,donotusethesaunawhenundertheinu-

ence of alcohol, medication or drugs.

●Never operate the sauna heater without sauna stones, as this

cancauseres.

● Makesurethatnoammableobjectshavebeenplacedonthe

sauna heater before the sauna control unit is switched on.

●Heat up the sauna heater for half an hour BEFORE using the

saunaforthersttime.DoNOTremaininthesaunacabinduring

this period. Then ventilate the sauna cabin well (see 5.2. Heating

for the rst time on page 19).

●Never touch the sauna heater while it is operating. The surfaces

of the sauna heater and sauna stones become extremely hot.

●For your own safety, consult your supplier in the event of problems

thatarenotdescribedinsucientdetailintheuserinstructions.

Instructions for installation and use p. 8/24

3. Product description

3.1. Scope of delivery

●Sauna heater

●Instructions for installation and use

3.2. Accessories

Accessories Item number

Cut-orockerswitch SFE-500500

Qube LIME wood railing (9, 10.5 kW) QUBE-L5

Qube LIME wood railing (12, 15 kW) QUBE-L6

Qube WALNUT wood railing (9, 10.5 kW) QUBE-W5

Qube WALNUT wood railing (12, 15 kW) QUBE-W6

Power booster O-S2-18 / O-S2-18S

3.3. Product functions

The Qube sauna heater is a Finnish sauna heater and makes it possible to

produce a typical Finnish sauna climate of 80 to 100 °C with an air humidity of

approximately 10%.

EN

Installation instructions, only for experts p. 9/24

4. Installation and connection

Take the following points into account when positioning and connecting the

sauna heater:

Ifthereissucientventilation,theQubesaunaheatercanalsobesitu-

atedinafree-standingposition.Inthiscase,tthetemperaturesensor

to the cabin roof above the centre of the heater.

●Theelectricalconnectionmayonlybeperformedbyaqualiedelectricianor

similarlyqualiedperson.

●A fully disconnecting all-pole isolating device compliant with overvoltage

categoryIIImustbettedonsite.

●The Qube sauna heater is a free-standing heater. It does not need to be at-

tachedtotheoororsaunawall.

●Donotplacethesaunaheateronaoormadefromaneasilyammable

materialsuchaswoodorplastic.Suitableooringincludesceramictiles,for

example.

●The 3-shell technology means that no additional protection against contact is

required because the surface temperatures of the heater are low.

4.1. Installation location and sensor position

Position the heater centrally in front of the air intake opening in the cabin wall.

ComplywiththesafetydistancestothecabinwallspeciedinFig. 1 and Fig. 2.

Install the temperature sensor with excess temperature cut-out to the cabin wall

above the centre of the sauna heater. Maintain a distance of 15 cm to the sauna

cabin roof.

WARNING!

Danger of electric shock

●The sauna heater may only be installed and connected when the

power supply is disconnected.

150

745-755

450450

min.

1940

min.

1185

min. 50min. 50

QUBE-090

QUBE-105

Installation instructions, only for experts p. 10/24

Fig. 1 Safety distances for Qube 9 kW and 10.5 kW

(QUBE-090 / QUBE-105)

Measurements in mm

4.2. Safety distances

ObservetheminimumsafetydistancesspeciedinFig. 1 and Fig. 2.

QUBE-120

QUBE-150

EN

Installation instructions, only for experts p. 11/24

150

745-755

450594

min.

1940

min.

1185

min. 50min. 50

4.3. Adjusting the height

The Qube sauna heater has height-adjustable feet. The height can therefore be

set between 745 mm and 755 mm. Each foot can be set individually, making it

possibletoadaptthesaunaheatertounevenoors.

1. Loosen the sauna heater foot using

an open-ended spanner (13 mm).

2. Lift the sauna heater slightly and turn

the foot to the right to reduce the height.

Turn to the left to increase the height.

3. Retighten the foot using the open-ended

spanner.

Fig. 2 Safety distances for Qube 12 kW and 15 kW

(QUBE-120 / QUBE-150)

Measurements in mm

L2 L2 N

L3 U

V

N

Wr

r

w

ϑϑ

400 V~

3x16 A

9 kW

10,5 kW

U

V

NW

WNVNU

Installation instructions, only for experts p. 12/24

4.4. Connection diagram for 400 V 3N~

Fig. 3 Connection diagram for 9 kW and 10.5 kW

(QUBE-090 / QUBE-105)

2

3

4

1 Sauna control unit

2 Temperature sensor with excess temperature cut-out

3 Qube sauna heater, 9 kW or 10.5 kW

4 Power supply

1

EN

Installation instructions, only for experts p. 13/24

L1 L2 N

L3 U

V

N

Wr

r

w

ϑϑ

U1

V1

N

W1

400 V~

3x16 A

12 kW und 15 kW

N

ST1

ST2

ST1

ST2

N

V2

W2

U2

L1 L2 N

L3

S2-18:

400 V~ 3x20 A

S2-18

S2-30

U2

V2

W2

S2-30:

400 V~ 3x35 A

N

ST3

Fig. 4 Connection diagram for 12 kW and 15 kW

(QUBE-120 / QUBE-150)

1

2

3

4

5

6

1 Sauna control unit

2 Temperature sensor with excess temperature cut-out

3 Qube sauna heater, 12 kW or 15 kW

4 Sauna control unit power supply

5 Power booster

6 Booster power supply

A12 kW and 15 kW

Installation instructions, only for experts p. 14/24

L1 L2 N

L3 U

V

N

Wr

r

w

ϑϑ

U

V

NW

W

230V 1N~

NVNU

L

PE

N

4.5. Connection diagram for 230 V 1N~

Connection diagram for 9 kW and 10.5 kW

(QUBE-090 / QUBE-105)

Fig. 5

1 Sauna control unit

2 Temperature sensor with excess temperature cut-out

3 Sauna heater, 9 kW or 10.5 kW

4 Power supply

Remove the copper bridge

1

4

3

2

*

EN

Installation instructions, only for experts p. 15/24

1,5 kW

U V W

1,5 kW

CP-R-090

9,0 kW

N N N

W V U

4.6. Wiring diagrams

1,5 kW

2,0 kW

1,5 kW

U V W

2,0 kW

1,5 kW

2,0 kW

CP-R-105

10,5 kW

N N N

W V U

To the

sauna

control unit

To the

sauna

control unit

QUBE-090

9.0 kW

QUBE-105

10.5 kW

Installation instructions, only for experts p. 16/24

1,5 kW

1,1 kW

U1V1W1

N

CP-R-120

12,0 kW

1,5 kW

1,1 kW

N

V2

1,5 kW

1,1 kW

U2

W2

To the

sauna

control unit

To the

power

booster

1,5 kW

2,0 kW

U1V1W1

N

CP-R-150

15,0 kW

1,5 kW

2,0 kW

N

V2

1,5 kW

2,0 kW

U2

W2

To the

sauna

control unit

To the

power

booster

9 kW 3.3 kW

9 kW 6 kW

QUBE-120

12.0 kW

QUBE-150

15.0 kW

U

V

W

N

PE

EN

Installation instructions, only for experts p. 17/24

Connection of Qube 9 kW and 10.5 kW

(QUBE-090 / QUBE-105)

1. Guide the connection cable through the feed-

through 4.

2. Connect the connectors of the connection

cable to the U – V – W – N – PE terminals

of the sauna heater and to the applicable

sauna control unit terminals. Observe the

installation instructions for the sauna control

unit when doing so.

3. Reattach the cover panel 1 to the heater.

4.7. Electrical connection

1. Unscrew the screws 2 and 3 with a screwdriver.

2. Remove the cover plate 1.

4

2

3

1

Installation instructions, only for experts p. 18/24

U1

V1

W1

N

U2

V2

W2

N

PE

Connection of Qube 12 kW and 15 kW

(QUBE-120 / QUBE-150)

1. Guide the connection cable for the sauna control unit through the feed-

through 6.

2. Connect the connectors of this connection cable to the U1 – V1 – W1 – N – PE

terminals on the connector block 7 and to the applicable sauna control unit

terminals. Observe the installation instructions for the sauna control unit when

doing so.

3. Guide the booster cable through the feed-through 5.

4. Connect the connectors of the booster cable to the U2 – V2 – W2 – N – PE

terminals on the connector block 4 and to the applicable booster terminals.

Observe the installation instructions of the booster when doing so.

5. Reattach the cover panel 1 to the heater.

4

5

7

6

4 Connector block for the booster

5 Feed-through for the booster cable

6 Feed-through for the connection cable for the sauna control unit

7 Connector block for the sauna control unit

EN

Instructions for use for the user p. 19/24

5. Commissioning

5.1. Filling the stone container

The amount of stones suited to your heater output can be found

in chapter 10. Technical data (see page 23).

1. Wash the stones thoroughly using water and a brush before use.

Do not use any cleaning additives.

2. Beforellingtheheaterwiththesaunastones,checkthemforforeignobjects

and remove any remaining packaging.

3. Place the stones in the stone container. Stack the sauna stones loosely so

thataircanowthroughthegaps.

4. Make sure that the sauna stones do not protrude beyond the edge of the

stone container.

WARNING!

Risk of re due to overheating

If the sauna heater is used without sauna stones, the cabin walls will

becomeextremelyhot.Thiscouldcauseres.

●NEVER operate the sauna heater without the sauna stones.

5.2. Heating for the rst time

CAUTION!

Formation of smoke and odours when heating up for the rst time

Materials used during the manufacturing process will be present on

the new heating elements. These evaporate when the sauna heater is

heatedupforthersttime.Thisproducessmokeandanunpleasant

odour. Breathing in the fumes or smoke can be harmful to your health.

Perform the following steps when operating the sauna heater for the rst

time and if the heating elements for the sauna heater have been replaced.

This prevents damage to health due to the fumes and smoke produced when

heatingforthersttime.

Instructions for use for the user p. 20/24

WARNING!

Risk of re

Combustible objects that are placed on the heater will ignite and cause

res.

●NEVER place combustible objects on the sauna heater.

●MakesurethatNOammableobjectshavebeenplacedonthe

heater before operating it.

6. Operation

6.1. Operating the sauna heater

A sauna control unit is used to operate the sauna heater. For information on how to

operate the sauna control unit, read the operating instructions for the device used.

6.2. Infusion

At the end of the sauna session, you can pour an infusion of water over the

stones. Pour water over the stones using a sauna ladle. The water evaporates

and the humidity in the sauna cabin increases.

When pouring water over the stones, observe the following points:

●Only use tap water. Sea water, hard water and chlorinated water can damage

the sauna heater.

●Only use fragrances and essential oils that are suitable for use in saunas. Follow

the manufacturer’s instructions on the packaging of the scented substance.

●Do not pour the water onto the stones too quickly. Only this way will all the

water evaporate completely.

1. Select the highest possible temperature on the sauna control unit.

2. Heat up the sauna heater for half an hour.

Do NOT remain in the sauna cabin during this period.

3. Allowthesaunacabintoventilatethoroughlyafterheatingforthersttime.

4. If no smoke or odours form the next time the sauna heater is heated, you

can start to use the sauna.

If smoke or odour is produced again, leave the sauna cabin immediately

and repeat the initial heating up process followed by ventilation.

Stránka sa načítava...

Sentiotec Qube Používateľská príručka

Súvisiace články

Ostatné dokumenty