ULTIMATE SPEED ULG 17 A1 Operation and Safety Notes

CAR BATTERY CHARGER &

JUMP STARTER ULG 17 A1

POLNILNIK ZA AKUMULATORJE

MOTORNIH VOZIL S FUNKCIJO

ZAGONA VOZILA ULG 17 A1

AUTONABÍJAČKA S FUNKCIOU

POMOCNÉHO ŠTARTOVANIA

ULG 17 A1

Operation and Safety Notes

Translation of the original instructions

Navodila za upravljanje in varnostna opozorila

Prevod originalnega navodila za uporabo

Návod na obsluhu a bezpečnostné upozornenia

Originálny návod na obsluhu

GB

SI

SK

KFZ-BATTERIELADEGERÄT

MIT STARTHILFEFUNKTION

ULG 17 A1

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung

DE AT CH

CAR BATTERY CHARGER & JUMP STARTER

ULG 17 A1

SKCZ

SIHU

IAN 322265_1901

AKKUMULÁTORTÖLTŐ

INDÍTÓFUNKCIÓVAL ULG 17 A1

AUTONABÍJEČKA S FUNKCÍ

POMOCNÉHO STARTOVÁNÍ

ULG 17 A1

Kezelési és biztonsági hivatkozások

Az eredeti használati utasítás fordítása

Návod k obsluze a bezpečnostní pokyny

Originální návod k obsluze

HU

CZ

322265_Kfz-Ladegerät_mit_Starthilfefunktion_ULG_17_A1_cover_LB4.indd 2 15.05.2019 16:46:50

GB

Before reading, unfold the page containing the illustrations and familiarise yourself with all

functions of the device.

HU

Olvasás előtt hajtsa ki az ábrát tartalmazó oldalt, és ezután ismerje meg a készülék

mindegyik funkcióját.

SI

Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.

CZ

Než začnete číst tento návod k obsluze, rozložte stránku s obrázky a seznamte se se

všemi funkcemi zařízení.

SK

Prv než začnete čítať tento návod, rozložte si stranu s obrázkami a potom sa oboznámte

so všetkými funkciami zariadenia.

DE

AT

CH

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich

anschließend mit allen Funktionen des Gerätes vertraut.

GB Operation and Safety Notes Page 5

HU Kezelési és biztonsági hivatkozások Oldal 19

SI Navodila za upravljanje in varnostna opozorila Stran 35

CZ Návod k obsluze a bezpečnostní pokyny Strana 51

SK Návod na obsluhu a bezpečnostné upozornenia Strana 65

DE/AT/CH Bedienungs- und Sicherheitshinweise Seite 79

322265_Kfz-Ladegerät_mit_Starthilfefunktion_ULG_17_A1_cover_LB4.indd 3 15.05.2019 16:46:50

A

B

1 2 3 4

567

8

322265_Kfz-Ladegerät_mit_Starthilfefunktion_ULG_17_A1_cover_LB4.indd 4 15.05.2019 16:46:51

322265_Kfz-Ladegerät_mit_Starthilfefunktion_ULG_17_A1_cover_LB4.indd 5 15.05.2019 16:46:51

5GB

Table of pictograms used ............................................................................... Page 6

Introduction ........................................................................................................... Page 6

Intended use ............................................................................................................. Page 6

Parts description ....................................................................................................... Page 7

Technical specifications ............................................................................................ Page 7

Package contents ...................................................................................................... Page 7

Safety instructions .............................................................................................. Page 8

Operation ............................................................................................................... Page 11

Product properties .................................................................................................... Page 11

Connection ............................................................................................................... Page 11

Disconnecting ........................................................................................................... Page 12

Select charging mode and start charging process ................................................... Page 12

Using the jump-start function ..................................................................................... Page 14

Alternator test function .............................................................................................. Page 15

Replacing the fuse .................................................................................................... Page 15

Maintenance and care ..................................................................................... Page 15

Warranty and service information ............................................................ Page 15

Warranty conditions ................................................................................................. Page 15

Warranty period and statutory claims for defects .................................................... Page 16

Extent of warranty .................................................................................................... Page 16

Processing of warranty claims .................................................................................. Page 16

Information about recycling and disposal ............................................. Page 17

EU Declaration of Conformity ....................................................................... Page 17

Table of contents

322265_Kfz-Ladegerät_mit_Starthilfefunktion_ULG_17_A1_content_LB4.indb 5 22.05.2019 08:58:45

6 GB

Car battery charger & jump

starter ULG 17 A1

z Introduction

Congratulations!

Y

ou have purchased one

of our high-quality products.

Please familiarise yourself with the

product before setup or first use. Read

the following original operating and

safety instructions carefully. This product

must be set up or used only by people who

have been trained to do so.

z Intended use

The Ultimate Speed ULG 17 A1 is a car

battery charger with pulse maintenance

charge (chip software), used for charging

and maintenance charging and suitable

for the following 6 V or 12 V-lead

rechargeable batteries (batteries)

with electrolyte solution, AGM batteries,

Table of pictograms used / Introduction

Table of pictograms used

Read the operating instructions

of this product attentively and

with care before use.

~50Hz

Alternating voltage with

a frequency of 50Hz

NOTE: This symbol indicates

additional information and

explanations on the product

and its use.

Caution! Possible risks!

Caution! Explosion hazard!

Caution! Risk of electric shock!

Protection class IP20:

Protection from the device

housing against touching live

or internal moving parts with

the fingers.

Dispose of the batteries in the

specified battery collection

points.

Suitable for lead-acid battery:

8 Ah – 250 Ah

Do not dispose of any

electrical devices in domestic

waste!

Only for use in closed,

ventilated rooms!

Dispose of packaging properly.

Do not dispose of the device in

household waste!

Packaging material –

corrugated paper

Suitable for cars

Suitable for motorbikes

Suitable for the charging

of 6-V batteries

Suitable for the charging

of 12-V batteries

Made from recycling material

322265_Kfz-Ladegerät_mit_Starthilfefunktion_ULG_17_A1_content_LB4.indb 6 22.05.2019 08:58:47

7GB

Introduction

lead-acid batteries, deep –

cycle (boat

batteries) or gel batteries:

 For car and motorcycle batteries with

12 V/6 V and 8-250 Ah capacity

You can also regenerate discharged batteries

(depending on the battery type). The car

battery charger has a safety circuit against

sparking and overheating. Keep these instruc

-

tions in a safe place. Ensure you hand over

all documentation when passing the product

on to anyone else. Any use that differs to the

intended use as stated above is prohibited

and potentially dangerous. Damage or injury

caused by misuse or disregarding the above

warning is not covered by the warranty or

any liability on the part of the manufacturer.

The device is not intended for commercial

use. Commercial use will void the guarantee.

Note: The car battery charger cannot charge

any electrical vehicles with

integrated rechargeable battery.

Note: No jumpstart of 6-V batteries possible.

z Parts description

1

Digital display button

2

Battery type button

3

Charge start button

4

“–” pole connection cable (black)

5

“+” pole connection cable (red)

6

Digital display

7

Mains cable

8

Fuse with cover

z Technical specifications

Input voltage: 230 V~ 50 Hz

Return current*: < 5 mA

(no AC input)

Nominal output voltage: 6 V/12 V

Charge current: 2 A, 6 A,

17 A ± 10%

Battery type with: 12 V/6 V and

8-250 Ah capacity

Housing protection type: IP 20

* = Return current means the current that

the car battery charger consumes from

the battery when no mains current is

connected.

Changes to technical and visual aspects of

the product may be made as part of future

developments without notice. Accordingly,

no warranty is offered for the physical

dimensions, information and specifications

in these operating instructions. The operating

instructions cannot therefore be used as the

basis for asserting a legal claim.

Note: The maximum load current essentially

depends on the internal resistance of the

connected battery. This internal resistance

is determined by the following factors: ages,

capacity and type of connected battery.

z Package contents

Check the scope of delivery and

the device as well as all parts for

damage right after unpacking.

Do not put a defective unit or

defective parts into operation.

1 Car battery charger Ultimate Speed

ULG 17 A1

2 Quick contact connection terminals

(1 red, 1 black)

1 original operating instructions

322265_Kfz-Ladegerät_mit_Starthilfefunktion_ULG_17_A1_content_LB4.indb 7 22.05.2019 08:58:47

8 GB

Safety instructions

z Safety instructions

KEEP OUT OF THE REACH OF

CHILDREN!

 DANGER! Avoid danger to

life and danger of injury from

improper use!

 CAUTION! Do not operate

the device with a damaged

cable, mains cable or mains

plug. Damaged mains cables

pose danger to life from elec-

tric shock.

 In case of damage, the mains

cable must only be repaired

by authorized and trained

specialists! Contact the service

point of your country if you

need any repair!

 DANGER OF ELECTRIC

SHOCK! Ensure that the

vehicle is not in operation if

the battery is installed firmly

in the vehicle! Switch off the

ignition and put the vehicle

into the parking position, with

the parking brake engaged

(e.g. car) or the rope attached

(e.g. electric boat)!

 DANGER OF ELECTRIC

SHOCK! Disconnect

the car battery charger from

the mains before removing

the connection terminals.

 Connect the connection termi-

nal that is not connected to the

car body first.

 Connect the other connection

terminal to the car body

away from the battery and

the gasoline line.

 Connect the car battery

charger to the supply grid

only thereafter.

 Disconnect the car battery

charger from the supply grid

after charging.

 Only then disconnect the

connection terminal from the

car body. Then disconnect the

connection terminal from the

battery.

 DANGER OF ELECTRIC

SHOCK! Only touch the

pole connection cables (“–”

and “+”) in the insulated area!

 DANGER OF ELECTRIC

SHOCK! Conduct the

connection to the battery and

the socket of the mains grid

completely protected from

moisture!

 DANGER OF ELECTRIC

SHOCK! Perform

installation, servicing and

322265_Kfz-Ladegerät_mit_Starthilfefunktion_ULG_17_A1_content_LB4.indb 8 22.05.2019 08:58:47

9GB

Safety instructions

maintenance of the car battery

charger only when the mains

current is not connected!

 DANGER OF ELECTRIC

SHOCK! First disconnect

the minus pole connection

cable (black) of the car battery

charger from the minus pole

of the battery upon completing

the charging and maintenance

charging process if the battery

is continually connected in the

vehicle.

 Do not leave any toddlers or

children unsupervised around

the car battery charger!

 Children cannot assess possi-

ble dangers in use of electrical

devices. Children must be

supervised to ensure that they

do not play with the device.

 This device may be used by

children aged 8 years and

older, and by persons with

reduced physical, sensory or

mental capacities, or a lack

of experience and knowledge,

if they are supervised or have

been instructed in how to use

the device safely and under-

stand the dangers that may arise

when using it. Do not allow

children to play with the device.

Cleaning and day-to-day mainte-

nance must not be performed by

children without supervision.

 EXPLOSION

HAZARD! Protect

yourself from highly explosive

oxyhydrogen reactions!

Gaseous hydrogen can escape

during charging or mainte-

nance charging of the battery.

Oxyhydrogen

is a potentially

explosive mixture

of gaseous

hydrogen and oxygen. The

oxyhydrogen reaction occurs

at contact with open fire

(flames, smouldering or sparks)!

Perform charging and

maintenance charging in a

weather-protected space that

is ventilated well. Ensure that

there are no open light

(flames, embers or sparks)

during charging or mainte-

nance charging!

 EXPLOSION AND FIRE

HAZARDS! Ensure that

explosive or flammable

substances, such as gasoline

or solvents cannot be ignited

when you are using the car

battery charger!

 EXPLOSIVE GASES!

Avoid flames and sparks!

 Ensure sufficient ventilation

when charging.

 Put the battery onto a well-

ventilated surface when

charging. Otherwise, the

device can be damaged.

322265_Kfz-Ladegerät_mit_Starthilfefunktion_ULG_17_A1_content_LB4.indb 9 22.05.2019 08:58:47

10 GB

 EXPLOSION

HAZARD! Ensure that

the plus-pole connection cable

has no contact with a fuel line

(e.g. petrol line)!

 DANGER OF CAUSTIC

BURNS!

Protect your eyes and skin

from caustic burns from the

acid (sulphuric acid) when it

comes into contact with the

battery!

 Use acid-resistant safety

goggles, clothing and gloves!

If your eyes or skin have come

into contract with the sulphuric

acid, flush the affected body

region with plenty of clear,

running water and seek

medical advice at once!

 Avoid electrical short circuits

when connecting the car

battery charger to the battery.

Only connect the minus pole

connection cable to the minus

pole of the battery or the car

body. Only connect the plus

pole connection cable to the

plus pole of the battery!

 Prior to connecting the mains

current, ensure that the mains

current is properly equipped

with 230 V~ 50 Hz, an

earthed zero conductor,

a 16 A fuse and an FI-switch

(fault-circuit interrupter)!

Otherwise, the device can

be damaged.

 Do not use the car battery

charger near any fires, heat

and long-term temperatures

above 50 °C! For higher

temperatures, the output power

of the car battery charger will

drop automatically.

 Only use the car battery

charger with the original

parts it was delivered with!

 Do not cover the car battery

charger with any objects!

Otherwise, the device can

be damaged.

 Protect the electrical contact

surfaces of the battery from

short circuit!

 Only use the car battery

charger for the charging and

maintenance charging of

undamaged 6 V-/12 V-lead

batteries (with electrolyte

solution or gel)! Otherwise,

property damage may be the

consequence.

 Do not use the car battery

charger for the charging and

maintenance charging of

non-rechargeable batteries.

Otherwise, property damage

may be the consequence.

 Do not use the car battery

charger for the charging and

maintenance charging of

Safety instructions

322265_Kfz-Ladegerät_mit_Starthilfefunktion_ULG_17_A1_content_LB4.indb 10 22.05.2019 08:58:47

11GB

Safety instructions / Operation

damaged or frozen batteries!

Otherwise, property damage

may be the consequence.

 Please refer to the original

operating instructions about

the maintenance of your

battery prior to connecting

the car battery charger!

Otherwise, there is a danger

of injury and/or the risk of

damage to the device.

 Before connecting the car

battery charger to a battery

that is continually connected

to the vehicle, learn about

compliance with the electrical

safety and maintenance in

the original operating instruc-

tions of the vehicle! Otherwise,

there is a danger of injury

and/or the risk of property

damage.

 Disconnect the car battery

charger from the mains current

when it is not in use to protect

the environment as well! Note

that power is also consumed in

the standby operation.

 Always pay attention and be

aware of what you are doing.

Proceed reasonably and do

not put the car battery charger

into operation when you are

not focused or not feeling well.

z Operation

Always pull the mains plug from the

socket before you perform any work

at the car battery charger.

DANGER OF ELECTRIC SHOCK!

DANGER OF PROPERTY DAMAGE!

DANGER OF INJURY!

z Product properties

This device is designed for charging many

SLA batteries (sealed lead-acid batteries),

which are mostly used in cars, motorcycles

and some other vehicles. They can be,

e.g., WET (with liquid electrolyte), GEL

(with electrolyte gel) or AGM batteries

(with electrolyte-absorbent mats). A special

design of the device (also called a “three-

stage charging strategy”) permits recharging

of the battery to nearly 100% of its capacity.

The battery may also be permanently

connected to the car battery charger in order

to keep it in optimal condition at all times.

Furthermore, the battery charger has an

integrated temperature sensor in the device

in order to safely charge the battery to full

even in cold weather (e.g. in the winter).

The device measures the ambient temperature

and automatically sets the optimal charging

voltage.

Note: The ambient temperature is measured

in the charger. Hence, for optimum function,

make sure the battery exhibits the same

temperature as the environment.

z Connection

 Disconnect the minus pole connection

cable (black) of the vehicle from the minus

pole of the battery first before charging

and maintenance charging if the battery

322265_Kfz-Ladegerät_mit_Starthilfefunktion_ULG_17_A1_content_LB4.indb 11 22.05.2019 08:58:47

12 GB

Operation

is continually connected in the vehicle.

The minus pole of your battery is usually

connected to the car body of the vehicle.

 Then disconnect the plus pole connection

cable (red) of the vehicle from the plus

pole of the battery.

 Only then connect the “+” pole quick con-

tact connection terminals (red)

5

of the

car charger to the “+”-pole of the battery.

 Connect the “–”-pole quick contact-con-

nection terminal (black)

4

to the “–”-pole

of the battery. Connect the mains cable

7

of the car charger to the socket.

Note: If the connection terminals are

connected correctly, the digital display

6

indicates the voltage and the “connected”

display lights up. In the event of reverse

polarity, the display will show 0.0 and the

reverse polarity LED

will light up in

red in the digital display

6

.

z Disconnecting

 Disconnect the device from the mains

current.

 Disconnect the “–”-pole quick con-

tact-connection terminal (black)

4

from

the “–”-pole of the battery.

 Disconnect the “+”-pole quick contact-

connection terminal (red)

5

from the

“+”-pole of the battery.

 Reconnect the plus pole connection

cable of the battery to the plus pole

of the battery.

 Reconnect the minus pole connection

cable of the battery to the minus pole

of the battery.

z Select charging mode

and start charging process

You can choose from different charging

modes to charge different batteries.

As compared to conventional car battery

chargers, this device has a special function

for reuse of a flat battery/rechargeable

battery. You can recharge a completely

discharged battery/rechargeable battery.

Protection against wrong connection and

short circuit ensures safe charging. The

integrated electronics do not start the car

battery charger at once after connection of

the battery, but only after a charging mode

has been selected.

If the connection terminals are connected to

the battery and the device is connected to

the mains, the digital display

6

will show

the “Connected” display. Once the charging

mode has been selected with the

charge

start button

3

, the “Charging” display will

light up. When charging is complete, the

“Charged” display lights up.

If the digital display “0.0” is continually lit

before the battery is completely charged,

there is a defect.

 In this case, check again if the connection

terminals

4

,

5

are correctly attached to

the battery and whether the correct bat-

tery type has been chosen. If the display

continually shows “0.0”, there may be a

defect in the battery.

Reactivation function /

reconditioning: If a voltage between 8.5 V

and 10.5 V is detected in the connected

battery, the device will automatically start a

reconditioning process in order to reactivate

the battery. If a voltage between 8.5 V and

10.5 V is measured after the reconditioning

process, then “Err” will be shown on the

digital display. In this case, the battery is

faulty and must be replaced.

Note: This function is only available

for 12 V batteries.

Digital display button

1

: Enables the

switch between the digital display of the

voltage and charging progress in percent

322265_Kfz-Ladegerät_mit_Starthilfefunktion_ULG_17_A1_content_LB4.indb 12 22.05.2019 08:58:47

13GB

Operation

(BATTERY %). Use this button to switch

between the following displays:

 Battery %: shows the charging progress

of the connected battery in percent.

 Voltage: shows the voltage of the

connected battery.

 Alternator % check: Output power of the

alternator in percent.

Battery type button

2

: Use this button

to set the battery type to be charged. You

can choose between different battery types.

The battery type must be correctly set before

starting the charging process:

 12 V – regular: These batteries (lead-acid

batteries) are usually used in cars, trucks

and motorcycles. They have venting caps

and are often marked as “low-mainte

-

nance” or “no maintenance”. This battery

type is meant for transferring energy

quickly (e.g. starting an engine).

“Regular” batteries should not be

used for “Deep – Cycle” applications.

 12 V Deep Cycle: These batteries are

usually also marked as “Deep – Cycle”

or “Marine”. Batteries of this type are

usually larger than other battery types.

This supplies less short-term energy,

but a longer-term energy transmission.

These batteries can withstand a large

number of discharge cycles.

 12 V – AGM/gel: The AGM battery

types are usually good deep – cycle bat-

teries. They have the best “service life”

when they are recharged before they

have been discharged by more than

50 %. At complete discharge they can

withstand about 300 charge cycles.

The battery type GEL is similar to the

battery type AGM. The voltage during

recharging is lower than in other lead-

acid batteries. If you use the wrong car

battery charger for a gel battery,

a reduced output or shorter service life

can be expected.

 6 V – regular: Choose this mode for

commercial rechargeable 6-V batteries.

Note: If you connect a 12 V car battery

to a car battery charger and the car battery

charger automatically detects it as a 6 V

battery, it can be assumed that this 12 V car

battery is faulty and needs to be replaced.

Charge-start button

3

: Use this button

to switch between the following options and

start the charging process:

 Fast Charge: fast charging

 Normal charge: normal charging

(normal speed)

 Start: briefly supplies 75 Ampere to

bridge batteries with a weak charge

or flat 12 V batteries for the purpose

of starting the engine

Note: In the Fast Charge mode the charg

-

er automatically switches to maintenance

charging after a successful charging process

(the “Charged” LED lights up in green in the

digital display

6

), provided the car battery

charger remains connect to the battery and

mains current.

Attention: Mode can only be terminated

by pulling the mains plug

7

or by

repeatedly pressing the charge start button

3

(repeated pressing until no mode is

displayed).

Note: If the “Charged” LED in the digital

display

6

lights up in green, the battery

is sufficiently charged and a repeated fast

or normal charging process is no longer

permitted.

322265_Kfz-Ladegerät_mit_Starthilfefunktion_ULG_17_A1_content_LB4.indb 13 22.05.2019 08:58:48

14 GB

Operation

z Using the jump-start

function

Always make all connections

as described and in the proper order. Other

-

wise, the electronic system of the vehicle can

be damaged.

If proceeding contrary to the specifications

described, you will act at your own risks and

responsibility.

Attention:

This function is not suitable for

batteries below 45 Ah. For batteries below

45 Ah, this function may damage the battery.

For diesel vehicles and large-volume gasoline

motors, higher currents than 75 A are needed

for starting at times.

Note: The car battery charger has an anal-

ysis program that protects the battery from

damage, particularly for the jump-start function

(e.g. sulphatisation, excessive voltage drops).

If the batteries are discharged very strongly or

subject to very high stress the device will not

activate the jump-starter to protect the battery.

During this process, the battery is already

being charged at low currents (charging is

lit). The display then stays at “0”. In this case,

jump starting is not possible. This protects the

battery from damage. The battery should be

charged first. The function “Fast Charge” or

“Normal Charge” can be used for this.

 Connect the “+” pole quick contact

connection terminals (red)

5

of the car

charger to the “+”-pole of the battery.

 Connect the “–”-pole quick contact-

connection terminal (black)

4

to the

“–”-pole of the battery. Connect the mains

cable

7

of the car charger to the socket.

 If the connection terminals are correctly

connected, the car battery charger will

automatically choose the correct 6 V or

12 V voltage. You may review the battery

type in the “Battery Type“ option field and

if necessary change it by pressing the

battery type button

2

.

 Now use the Charge-Start button

3

to

select the function “Start”. The car battery

charger now analyses the charge condi

-

tion of the battery. The display will now

read “0“.

 Now actuate the vehicle's ignition. The

display will now show a 5 second count

-

down (of which 2 second priming /

analysis function and 3 second jump start

function at 75 A) when needing the car

battery charger for jump starting

(previously analysed by the car battery

charger). During this countdown, your car

battery charger will briefly supply 75 A,

in order to bridge the battery for the

purposes of starting the engine. This will

be followed by a break of 180 seconds to

protect the battery. Now the cycle restarts

(2 seconds lead or analysis function and

3 seconds jump-start function at 75 A /

180 seconds pause).

 To disconnect the device, first remove the

connection terminals first (

4

/

5

) and

then pull the mains cable

7

.

Note: If the battery is discharged entirely,

the 75 A will not be sufficient to start the

engine in all vehicles (e.g. diesel vehicles).

 In this case, use the

Charge-Start button

3

to select the option “Fast Charge”

and then charge the battery to 60%

(for diesel engines, the warm-up with-

draws energy from the battery. The 60%

must be pending after warm-up).

 You can track the charging progress on

the display by selecting the “Battery %”

option with the digital display button

1

.

 When 60% is reached, repeat the jump-

start function.

Attention: End the mode by pulling the

mains plug

7

.

322265_Kfz-Ladegerät_mit_Starthilfefunktion_ULG_17_A1_content_LB4.indb 14 22.05.2019 08:58:48

15GB

Operation / Maintenance and care / Warranty and service information

z Alternator test function

 Attach the red connection terminals

5

to the plus pole of your battery. (The plus

pole is marked by a “+” and a red mark.)

 Attach the black connection terminals

4

to the minus pole of your battery.

(The minus pole is marked by a “–” and a

black mark.)

 Connect the mains cable

7

of the car

battery charger to the socket.

Set the “Alternator” function (LED next to

the alternator) via the button

1

. A %-value

is displayed. Start the engine. If the %-value

rises with the engine running, the alternator

will charge the battery. If the %-value drops

or remains the same, there is a problem with

the alternator, the connection or the battery.

 Disconnect the device from the mains

current.

 Disconnect the “–”-pole quick contact-

connection terminal (black)

4

from the

“–”-pole of the battery.

 Disconnect the “+”-pole quick contact-

connection terminal (red)

5

from the

“+”-pole of the battery.

z Replacing the fuse

The fuse of the car battery charger may

be damaged, e.g. by a device defect,

overload, etc.

 Before replacing the fuse, pull the

mains cable

7

.

 Remove the cover of the fuse

8

by depressing it slightly on the side.

 Unscrew the fuse with a suitable open-

end spanner and secure the new fuse.

 Then tighten it and reattached the cover

8

.

Note: If you need a new fuse, contact our

service (see chapter with notes on guarantee

and service processing).

z Maintenance and care

 Always pull the mains cable

7

from the

socket before you perform any work at

the car charger.

 The device is maintenance-free.

Deactivate the device. Clean the metal

and plastic surfaces of the device with

a dry cloth.

 Never use any solvents or other aggres-

sive cleaning agents.

z Warranty and service

information

Warranty from Creative

Marketing & Consulting GmbH

Dear Customer,

The warranty for this equipment is 3 years

from the date of purchase. In the event of

product defects, you have legal rights against

the retailer of this product. Your statutory

rights are not affected in any way by our

warranty conditions, which are described

below.

z Warranty conditions

The warranty period begins on the date

of purchase. Please retain the original

proof of purchase. This document is required

as your proof of purchase. Should this

product have a material or manufacturing

error within three years of the purchase

date, the product will be repaired or

replaced – dependent on our choice – by

us at no cost to you. This warranty service

requires that you retain proof of purchase

(sales receipt) for the defective device for the

three year period and that you briefly explain

in writing what the fault entails and when it

occurred.

If the defect is covered by our warranty, we

will repair and return your product or send

322265_Kfz-Ladegerät_mit_Starthilfefunktion_ULG_17_A1_content_LB4.indb 15 22.05.2019 08:58:48

16 GB

Warranty and service information

you a replacement. The original warranty

period is not extended when a device is

repair or replaced.

z Warranty period and

statutory claims for defects

The warranty period is not extended by the

guarantee. This also applies to replaced

and repaired parts. Any damages or defects

detected at the time of purchase must be

reported immediately after unpacking. Any

incidental repairs after the warranty period

are subject to a fee.

z Extent of warranty

This device has been manufactured accord-

ing to strict quality guidelines and carefully

inspected before delivery.

The warranty applies to material and

manufacturing defects only. This warranty

does not extend to product parts, which are

subject to normal wear and tear and can

thus be regarded as consumable parts, or

for damages to fragile parts, e.g. switches,

rechargeable batteries or parts made from

glass. This warranty is voided if the product

becomes damaged or is improperly used or

maintained. For proper use of the product,

all of the instructions given in the original

operating instructions must be followed

precisely. Uses and acts that the original

operating instructions advise or warn against

are to be avoided without question.

The product is for consumer use only and is

not intended for commercial or trade use. The

warranty becomes void in the event of misuse

and improper use, use of force, and any

work on the device that has not been carried

out by our authorised service branch.

z Processing of warranty

claims

Please follow the instructions below to

ensure quick processing of your claim:

Please retain proof of purchase and the

article number (e.g. IAN) for all inquiries.

The product number can be found on the type

plate, an engraving, the cover page of your

instructions (bottom left), or the sticker on the

back or underside of the device. In the event

of malfunctions or other defects, please first

contact our service department below by

phone or email.

If your product is found to be defective, you

can then send your product with proof of

purchase (till receipt) and a statement

describing what the fault involves and when

it occurred free of charge to the service –

address given.

Note:

You can download this hand

-

book and many more, as well as

product videos and software at

www.lidl-service.com.

With this QR code you can gain

immediate access to the Lidl Service page

(www.lidl-service.com) and you can open

your operating instructions by entering the

article number (IAN) 322265_1901.

322265_Kfz-Ladegerät_mit_Starthilfefunktion_ULG_17_A1_content_LB4.indb 16 22.05.2019 08:58:48

17GB

How to contact us:

GB

Name: C. M. C. GmbH

Website: www.cmc-creative.de

E-mail: ser[email protected]

Phone: 0-808-189-0652

Registered office: Germany

IAN 322265_1901

Please note that the following address is not

a service address. Please first contact the

service point given above.

Address:

C. M. C. GmbH

Katharina-Loth-Str. 15

66386 St. Ingbert

GERMANY

Ordering spare parts:

www.ersatzteile.cmc-creative.de

z Information about recycling

and disposal

Do not dispose of electrical

tools in household waste!

Please return this device, accessories

and packaging to your local recycling

depot.

Do not dispose of the car battery charger in

household waste, in fire or in water. Devic

-

es that are no longer functional should be

recycled wherever possible. Ask your local

stockist for advice.

As the consumer you are legally

obliged (by the German Battery

Ordinance) to return any and all

used batteries. Batteries containing harmful

substances are labelled with the adjacent

symbol, which indicates the prohibition on

disposal in household waste. The abbrevia

-

tions for the relevant heavy metals are:

Cd = cadmium, Hg = mercury, Pb = lead.

Take used batteries to a waste management

company in your city or community or return

them to your dealer. This satisfies your legal

obligations while also making an important

contribution to protecting the environment.

z EU Declaration of

Conformity

We,

C. M. C. GmbH

Responsible for documentation:

Alexander Hoffmann

Katharina-Loth-Str. 15

66386 St. Ingbert

Germany

hereby take sole responsibility for declaring

that the product

Car battery charger & jump starter

Year of manufacture: 2019 / 40

IAN: 322265_1901

Model: ULG 17 A1

Model number: 2201

meets the basic safety requirements as

specified in the European Directives

Low Voltage Directive

2014 / 35 / EU

Electromagnetic Compatibility

2014 / 30 / EU

RoHS Directive

2011 / 65 / EU + 2015 / 863 / EU

and the amendments to these directives.

The object of the declaration described

above meets the requirements of Directive

... / Information about recycling and disposal / EU Declaration of Conformity

322265_Kfz-Ladegerät_mit_Starthilfefunktion_ULG_17_A1_content_LB4.indb 17 22.05.2019 08:58:48

18 GB

EU Declaration of Conformity

2011/65/EU of the European Parliament

and of the Council of 8 June 2011 on the

restriction of the use of certain hazardous sub

-

stances in electrical and electronic equipment.

This conformity assessment is based on the

following harmonised standards:

EN 60335-2-29:2004/A2:2010

EN 60335-1:2012/A11:2014

EN 62233:2008

EN 50498:2010

EN 55014-1:2006/A2:2011

EN 55014-2:1997/A2:2008

EN 61000-3-2:2014

EN 61000-3-3:2013

St. Ingbert, 06/05/2019

Alexander Hoffmann

– Quality Assurance –

322265_Kfz-Ladegerät_mit_Starthilfefunktion_ULG_17_A1_content_LB4.indb 18 22.05.2019 08:58:49

19HU

A használt piktogramok táblázata ........................................................................... Oldal 20

Bevezetés............................................................................................................................. Oldal 20

Rendeltetésszerűhasználat ............................................................................................. Oldal 20

Azalkatrészekleírása ....................................................................................................... Oldal 21

Műszakiadatok ................................................................................................................... Oldal 21

Szállításiterjedelem .......................................................................................................... Oldal 21

Biztonsági tudnivalók .................................................................................................... Oldal 22

Kezelés .................................................................................................................................. Oldal 25

Terméktulajdonságok ........................................................................................................ Oldal 25

Csatlakoztatás .................................................................................................................... Oldal 26

Leválasztás ......................................................................................................................... Oldal 26

Atöltésimódkiválasztásaésatöltésifolyamatindítása ............................................ Oldal 26

Indítássegítőfunkcióhasználata ..................................................................................... Oldal 28

Generátortesztfunkció ...................................................................................................... Oldal 29

Biztosítékcseréje ............................................................................................................... Oldal 30

Karbantartás és ápolás ................................................................................................. Oldal 30

Garanciával és szervizeléssel kapcsolatos tudnivalók................................. Oldal 30

Garanciálisfeltételek ......................................................................................................... Oldal 30

Garanciaidőéstörvényialapúreklamációk .................................................................. Oldal 30

Agaranciaterjedelme ........................................................................................................ Oldal 31

Eljárásgaranciálisesetben .............................................................................................. Oldal 31

Környezetvédelemmel és ártalmatlanítással kapcsolatos tudnivalók... Oldal 32

EU-megfelelőségi nyilatkozat .................................................................................... Oldal 32

Hu jótállási tájékoztató .................................................................................................. Oldal 34

Tartalomjegyzék

322265_Kfz-Ladegerät_mit_Starthilfefunktion_ULG_17_A1_content_LB4.indb 19 22.05.2019 08:58:49

20 HU

Akkumulátortöltő indítófunkcióval

ULG 17 A1

z Bevezetés

Gratulálunk!

Vállalatunkkiválóminőségűterméke

mellettdöntött.Mégazelsőüzembe

helyezéselőttismerkedjenmegatermékkel.

Ehhezgyelmesenolvassaelakövetkező

eredetihasználatiútmutatótésabiztonsági

tudnivalókat.Aterméküzembehelyezését

csakoktatásbanrészesítettszemély

végezheti.

z Rendeltetésszerű használat

AzUltimateSpeedULG17A1egygépjár-

mű-akkumulátortöltőkészülékimpulzusos

fenntartótöltéssel(chipszoftver),amely

akövetkezőelektrolitoldatos6V-osvagy

12V-osólomakkumulátorok(telepek),

AGM-akkumulátorok,savasólomakkumuláto-

rok,mélyciklusú(hajó-)akkumulátorokvagy

Ahasználtpiktogramoktáblázata/Bevezetés

A használt piktogramok táblázata

Atermékhasználataelőtt

olvassaelgyelmesenésteljes

egészébenakezelésiútmutatót.

~50Hz

Váltakozófeszültség50Hz

frekvenciával

FONTOS TUDNIVALÓ:

Ezaszimbólumatermékkel

éshasználatávalkapcsolatos

továbbiinformációkraés

magyarázatokrautal.

Vigyázat!

Lehetségesveszélyek!

Vigyázat!

Robbanásveszély!

Vigyázat!

Áramütésveszélye!

IP20védettségiosztály:

Akészülékházaáltalnyújtott

védelemfeszültségalattálló

vagyakészülékbelsejében

lévő,mozgóalkatrészekujjal

történőmegérintéseellen.

Azakkumulátorokatazerre

acélraszolgálóakkumulátor-

leadóhelyekenártalmatlanítsa.

Ilyensavasólomakkumulátor-

hozalkalmas:8Ah–250Ah

Nedobjaazelektromos

készülékeketaháztartási

szemétközé!

Csakzárt,szellőztetettterekben

történőalkalmazásra!

Környezetkímélőmódon

ártalmatlanítsaakészüléket

ésacsomagolását!

Csomagolóanyag-hullámpapír

Alkalmas

személygépkocsikhoz

Alkalmasmotorkerékpárokhoz

Alkalmas6V-os

akkumulátoroktöltéséhez

Alkalmas12V-os

akkumulátoroktöltéséhez

Újrahasznosítható

anyagokbólkészült

322265_Kfz-Ladegerät_mit_Starthilfefunktion_ULG_17_A1_content_LB4.indb 20 22.05.2019 08:58:50

Stránka sa načítava...

ULTIMATE SPEED ULG 17 A1 Operation and Safety Notes

ULTIMATE SPEED ULG 17 A1 Operation and Safety Notes

v iných jazykoch

Súvisiace články

Ostatné dokumenty