Hach sensION+ DL Používateľská príručka

DOC022.98.80155

sensION

™

+ DL Portable Meter

07/2017, Edition 2

User Manual

Bedienungsanleitung

Manuale dell'utente

Manuel d'utilisation

Manual del usuario

Manual do utilizador

Uživatelská příručka

Brugsanvisning

Gebruikershandleiding

Instrukcja obsługi

Bruksanvisning

Käyttäjän käsikirja

Ръководство на потребителя

Használati útmutató

Manual de utilizare

Naudotojo vadovas

Руководство пользователя

Kullanım Kılavuzu

Návod na obsluhu

Navodila za uporabo

Korisnički priručnik

Εγχειρίδιο λειτουργίας

Kasutusjuhend

English...................................................................................................................................................................................................3

Deutsch...............................................................................................................................................................................................20

Italiano................................................................................................................................................................................................. 40

Français.............................................................................................................................................................................................. 59

Español............................................................................................................................................................................................... 79

Português.......................................................................................................................................................................................... 98

Čeština.............................................................................................................................................................................................. 117

Dansk.................................................................................................................................................................................................135

Nederlands...................................................................................................................................................................................... 153

Polski................................................................................................................................................................................................. 174

Svenska............................................................................................................................................................................................ 193

Suomi.................................................................................................................................................................................................211

български....................................................................................................................................................................................... 229

Magyar.............................................................................................................................................................................................. 249

Română............................................................................................................................................................................................ 268

lietuvių kalba...................................................................................................................................................................................286

Русский............................................................................................................................................................................................ 304

Türkçe................................................................................................................................................................................................324

Slovenský jazyk............................................................................................................................................................................ 341

Slovenski.......................................................................................................................................................................................... 359

Hrvatski............................................................................................................................................................................................. 377

Ελληνικά........................................................................................................................................................................................... 395

eesti keel.......................................................................................................................................................................................... 415

2

Table of Contents

Specifications on page 3

General information on page 4

Installation on page 5

User interface and navigation on page 6

Startup on page 10

Operation on page 10

Data logger on page 13

Data transfer on page 14

Maintenance on page 15

Troubleshooting on page 16

Replacement parts and accessories on page 17

Standard solutions on page 18

Salinity values for dissolved oxygen meters on page 19

Specifications

Specifications are subject to change without notice.

Specification Details

Dimensions 18.6 x 7.3 x 3.8 cm (7.32 x 2.87 x 1.5 in.)

Weight 300 g (0.66 lb)

Meter enclosure IP67

Power requirements

(internal)

AA Alkaline or rechargeable Nickel Metal Hydride

(NiMH) batteries (3); battery life: over 500 hours

Input connectors MP-5 or MP-8 connector for sensION+ probes

Meter protection class Class III

Storage temperature –15 to +65 °C (5 to +149 °F)

Operating temperature 0 to 50 °C (32 to 122 °F)

Operating humidity 80% (non-condensing)

Specification Details

Datalog Maximum 500 data points, automatic or manual

save

Wireless data transfer USB-RF device, maximum operation distance 10 m

RF Output power RF Dongle: -16.01 dBm (tolerance -4 to +2 dBm)

Instruments: -4,01 dBm (tolerance -4 to +2 dBm)

Instrument range pH: –2.00 to 19.99; ORP: ±1999 mV

Conductivity: 0.01 to 500 mS/cm; TDS: 0 to 500 g/L;

Salinity: 0.0 to 1999 mg/L, 2.0 to 50.0 g/L

DO: 0.00 to 19.99 mg/L and 20.0 to 22.0 mg/L

(25°C), 0.0 to 199.9% and 200 to 250% (25°C)

Resolution pH: 0.01 pH; ORP: 1 mV (0.1 mV from –199.9 to

199.9 mV)

DO: 0.1% (1% if ≥ 200%); 0.01 mg/L (0.1 mg/L if ≥

20 mg/L)

Conductivity: changes with range (auto-ranging)

Temperature: 0.1 °C (0.1°F)

Measuring error (± 1 digit) pH: ≤ 0.01 pH; ORP: ≤ 1 mV

DO: ≤ 0.5% of the measured value

Conductivity: ≤ 0.5% (0.01 µS/cm to 19.99 mS/cm);

≤ 1% (≥ 20.0 mS). Salinity/TDS: ≤ 0.5%

Temperature: ≤ 0.2 °C (≤ 0.4 °F)

Reproducibility (± 1 digit) pH: ± 0.01 pH; ORP ± 1 mV

DO: ≤ 0.2 of the measured value

Conductivity/Salinity/TDS: ± 0.1%

Temperature ± 0.1 °C (± 0.1 °F)

Reference temperature

(RT)

Conductivity: 20 or 25 °C (68 or 77 °F) (factory

settings: 25 °C (77 °F))

English 3

Specification Details

Temperature coefficient

(TC)

Conductivity: 0.00 to 5.00%/°C (factory settings: 2%/

°C)

TDS conversion factor Conductivity: 0.00 to 4.44 (factory settings: 0.64)

Energy management Automatic power off after 5 minutes of inactivity

Certification EU: CE and NB (wireless) and FCC/IC (wireless)

General information

Revised editions are found on the manufacturer’s website.

Safety information

N O T I C E

The manufacturer is not responsible for any damages due to misapplication or

misuse of this product including, without limitation, direct, incidental and

consequential damages, and disclaims such damages to the full extent permitted

under applicable law. The user is solely responsible to identify critical application

risks and install appropriate mechanisms to protect processes during a possible

equipment malfunction.

Please read this entire manual before unpacking, setting up or operating

this equipment. Pay attention to all danger and caution statements.

Failure to do so could result in serious injury to the operator or damage

to the equipment.

Make sure that the protection provided by this equipment is not impaired.

Do not use or install this equipment in any manner other than that

specified in this manual.

Use of hazard information

D A N G E R

Indicates a potentially or imminently hazardous situation which, if not avoided, will

result in death or serious injury.

W A R N I N G

Indicates a potentially or imminently hazardous situation which, if not avoided,

could result in death or serious injury.

C A U T I O N

Indicates a potentially hazardous situation that may result in minor or moderate

injury.

N O T I C E

Indicates a situation which, if not avoided, may cause damage to the instrument.

Information that requires special emphasis.

Precautionary labels

Read all labels and tags attached to the instrument. Personal injury or

damage to the instrument could occur if not observed. A symbol on the

instrument is referenced in the manual with a precautionary statement.

This symbol, if noted on the instrument, references the instruction

manual for operation and/or safety information.

Electrical equipment marked with this symbol may not be disposed of

in European public disposal systems after 12 August of 2005. In

conformity with European local and national regulations (EU Directive

2002/96/EC), European electrical equipment users must now return

old or end-of-life equipment to the Producer for disposal at no charge

to the user.

Note: For return for recycling, please contact the equipment producer or supplier

for instructions on how to return end-of-life equipment, producer-supplied

electrical accessories, and all auxiliary items for proper disposal.

Regulatory device approval

sensION

™

+ meter

• Contains FCC ID: VIC-C0553

• Contains IC ID: 6149A-C0553

portCom DL USB-RF device

4

English

• FCC ID: VIC-C0554

• IC ID: 6149A-C0554

This device complies with Part 15 of the FCC Rules and Industry

Canada license-exempt RSS standard(s). Operation is subject to the

following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that

may cause undesired operation of the device.

Warning - Unauthorized modification or changes to this wireless

communication equipment will void the right to use it. Changes or

modifications to this unit not expressly approved by the party responsible

for compliance will void the user's authority to operate the equipment.

Any change to the equipment will void the Industry Canada certification

and FCC grant.

Product overview

The sensION

™

+ series meters are used with sensION+ probes to

measure various parameters in water. Primarily for field use, the portable

meter operates on three AA batteries.

The sensION

™

+ series meters are available in 5 models:

• sensION

™

+ EC5 DL—conductivity, TDS, salinity and temperature

meter

• sensION

™

+ MM150 DL—pH, ORP (Redox), conductivity, TDS and

temperature meter

• sensION

™

+ MM110 DL—pH, ORP (Redox) and temperature meter

• sensION

™

+ MM156 DL—pH, conductivity, salinity, dissolved oxygen

and temperature meter

• sensION

™

+ pH1 DL—pH meter

• sensION

™

+ DO6 DL—dissolved oxygen (concentration and %

saturation) and temperature meter

Installation

Install the batteries

W A R N I N G

Explosion hazard. Incorrect battery installation can cause the release of explosive

gases. Be sure that the batteries are of the same approved chemical type and

are inserted in the correct orientation. Do not mix new and used batteries.

N O T I C E

The battery compartment is not waterproof. If the battery compartment becomes

wet, remove and dry the batteries and dry the interior of the compartment. Check

the battery contacts for corrosion and clean them if necessary.

N O T I C E

When using nickel metal hydride (NiMH) batteries, the battery icon will not

indicate a full charge after freshly charged batteries have been inserted (NiMH

batteries are 1.2 V versus 1.5 V for alkaline batteries). Even though the icon does

not indicate complete charge, 2300 mAH NiMH batteries will achieve 90% of

instrument operation lifetime (before recharge) versus new alkaline batteries.

N O T I C E

To avoid potential damage to the meter from battery leakage, remove the meter

batteries prior to extended periods of non-use.

The meter can be powered with AA alkaline or rechargeable NiMH

batteries. To conserve battery life, the meter will power off after

5 minutes of inactivity. This time can be changed in the Display Options

menu.

English 5

For battery installation, refer to Figure 1.

Note: A tool such as a flat screwdriver may be necessary the first time the cover is

removed.

Make sure that the cover is tightly closed to maintain the IP67 enclosure

rating.

Figure 1 Battery installation

Connect a probe

1. Plug the probe into the meter (Figure 2).

2. Push the connector so that the alignment pin goes into the groove on

the female connector.

Note: Do not turn the connector.

Figure 2 Probe connection

User interface and navigation

User interface

Figure 3 Keypad description

1 DISPLAY LIGHT key 5 DOWN key

2 DATALOG key 6 ON/OFF

3 UP key 7 CALIBRATION key

4 MEASUREMENT key

6 English

Display description

The display shows 3 types of screens:

• Measure—the most recent parameter measurement is shown with the

temperature and stabilization time.

• Calibration—the calibration standard values and temperature are

shown during a calibration.

• Standby—the screen is empty except for the measurement timer at

the bottom.

Figure 4 PH1 DL screen display

1 Data transfer icon 4 Measurement time (hh:mm:ss)

2 Measurement units 5 Temperature

3 Battery indicator 6 Measurement value (pH or ORP)

Figure 5 DO6 DL screen display

1 Data transfer icon 4 Measurement time (hh:mm:ss)

2 Measurement units 5 Temperature

3 Battery indicator 6 Measurement value (DO)

English 7

Figure 6 MM110 DL screen display

1 Data transfer icon 5 Temperature

2 Measurement units 6 Measurement value (ORP)

3 Battery indicator 7 Measurement value (pH)

4 Measurement time (hh:mm:ss)

Figure 7 MM150 DL screen display

1 Data transfer icon 6 Temperature

2 Measurement value (pH) 7 Measurement value (TDS, ORP)

3 Measurement units 8 Reference temperature

4 Battery indicator 9 Measurement value (conductivity)

5 Measurement time (hh:mm:ss)

8 English

Figure 8 MM156 DL screen display

1 Data transfer icon 6 Temperature

2 Measurement value (pH) 7 Measurement value (DO, salinity)

3 Measurement units 8 Reference temperature

4 Battery indicator 9 Measurement value (conductivity)

5 Measurement time (hh:mm:ss)

Figure 9 EC5 DL screen display

1 Data transfer icon 5 Measurement time (hh:mm:ss)

2 Measurement units 6 Measurement value (conductivity,

salinity, TDS)

3 Temperature 7 Reference temperature

4 Battery indicator

Navigation

Use the calibrate key to calibrate the probe. Use the measure key

to take a sample measurement. Use the arrow keys to scroll to

other options or to change a value. Use the datalog key

to save or

view data or to send data to a computer.

Some options require that a key be pushed and held or that multiple

keys be pushed at the same time. Be sure to look at the display during

tasks as the screens change quickly. Refer to each task for specific

instructions.

English

9

Startup

Turn the meter on and off

N O T I C E

Make sure that the probe is connected to the meter before the meter is turned on.

Push and hold to turn on or turn off the meter. If the meter does not

turn on, make sure that the batteries are properly installed.

Note: The meter is set to automatically power off after 5 minutes of inactivity to

maximize the battery life.

Operation

D A N G E R

Chemical exposure hazard. Obey laboratory safety procedures and

wear all of the personal protective equipment appropriate to the

chemicals that are handled. Refer to the current safety data sheets

(MSDS/SDS) for safety protocols.

W A R N I N G

Pacemaker precautions. If electromagnetic interference (EMI) occurs,

it can either:

• Stop the stimulating pulses from the pacemaker that control the

rhythm of the heart.

• Cause the pacemaker to supply the pulses irregularly.

• Cause the pacemaker to ignore the rhythm of the heart and supply

pulses at a set interval.

Current research shows that cellular devices are not a significant

health problem for most pacemakers wearers. However, persons with

pacemakers should use precautions to make sure that their device

does not cause a problem. Keep the device a minimum of 20 cm

(7.9 in.) from the user.

C A U T I O N

Electromagnetic radiation hazard. Make sure that the antenna is kept at

a minimum distance of 20 cm (7.9 in.) from all personnel in normal use.

The antenna cannot be co-located or operated in conjunction with any

other antenna or transmitters.

Setup for pH

The meter is ready for pH or ORP calibration without additional setup.

Setup for dissolved oxygen

Before a calibration or a measurement for dissolved oxygen, the probe

must be polarized and the settings for atmospheric pressure and salinity

must be entered.

Polarize the electrode

If the probe or batteries are disconnected, connect the probe or install

the batteries and wait for polarization:

Disconnect time Polarization time

< 5 minutes 10 minutes

5 to 15 minutes 45 minutes

> 15 minutes 6 hours

10 English

Change the settings

The settings for dissolved oxygen measurements can be changed when

a dissolved oxygen probe is used. Push to view the current settings.

1. Push . The first setting is shown.

2. Quickly use the arrow keys to change the value. Wait for the next

setting to be shown and change any additional values:

Option Description

Atmospheric pressure in mbar (default: 1013 mbar)

SAL Salinity in g/L NaCl (default: 0 g/L)

Aut: automatic (only in model MM156)

Note: The salinity value can be found from a conductivity measurement. Refer

to Table 3 on page 19.

Setup for conductivity

The settings for conductivity measurements can be changed when a

conductivity probe is used. Push to view the current settings.

1. Push . The first setting is shown.

2. Quickly use the arrow keys to change the value. Wait for the next

setting to be shown and change any additional values:

Option Description

CEL Electrode type: platinum (default) or titanium.

Note: This option is not available on all meters.

CAL The number of standards for conductivity calibration. Select one

standard (default). Select the standard nearest to the expected

measurement range.

tC Temperature compensation: 0 to 9.99%/°C (default: 2%/°C)

tr Reference temperature: 20 or 25 °C (default: 25 °C)

F TDS calculation factor: 0.01 to 4.44 (default: 0.64)

The new settings are automatically stored in the meter.

Calibration

W A R N I N G

Chemical exposure hazard. Obey laboratory safety procedures and wear all of

the personal protective equipment appropriate to the chemicals that are handled.

Refer to the current material safety data sheets (MSDS) for safety protocols.

Calibration procedure

This procedure is for general use with liquid calibration solutions. Refer

to the documents that are included with each probe for additional

information.

1. Pour the buffers or calibration solution into the labeled calibration

tubes.

2. Rinse the probe with deionized water and put the probe into the

appropriate calibration tube. Make sure that there are no air bubbles

under the probe tip.

3. Push . The parameter flashes.

4. Use the arrow keys to change the parameter, if applicable.

5. Push to select the parameter.

6. Push the arrow keys to select the appropriate standard solution. For

pH, the buffers are automatically recognized.

7. Push to measure the calibration solution.

Note: For pH, the next calibration solution is shown. For conductivity, use one

calibration point. Select the standard nearest to the expected measurement

range.

8. Rinse the probe with deionized water and put the probe into the

second calibration tube, if applicable. Make sure that there are no air

bubbles under the probe tip.

9. Push to measure the second calibration solution, if applicable.

The next calibration solution is shown.

10. Rinse the probe with deionized water and put the probe into the third

calibration tube. Make sure that there are no air bubbles under the

probe tip.

11. Push to measure the third calibration solution, if applicable.

English

11

When the calibration is good, the display briefly shows OK and then

goes to the standby mode.

Note: To calibrate with only 1 or 2 standards when additional standards are

supplied, push after the first or second standard is measured.

View the calibration data

Data from the most recent calibration can be shown for pH, ORP and

conductivity.

1. Push .

2. Use the arrow keys to change the parameter, if necessary, and push

.

3. Push and at the same time. The calibration data is shown:

• pH—the slope and offset values are shown alternating with the

deviation (in %) and calibration temperature.

• ORP—the measured mV value and calibration temperature are

shown.

• Conductivity—the cell constant and calibration temperature for

each standard are shown.

Restore the factory calibration

The user calibration can be erased and the factory calibration restored

for pH, ORP and conductivity.

1. Push . The parameter flashes.

2. Use the arrow keys to change the parameter, if necessary.

3. Push and hold until OFF is shown.

The factory calibration for the selected parameter is restored.

Adjust the calibration

The instrument can be adjusted to read a specified solution value for pH,

ORP and conductivity.

1. Rinse the probe. Put the probe in the solution.

2. Push to read the value of the solution.

3. Push . The parameter flashes.

4. Use the arrow keys to select the parameter, if necessary.

5. Push and hold and then push .

The measured value flashes.

6. Use the arrow keys to change the value.

7. Push . The display shows OK.

Adjust the temperature

The temperature measurement can be adjusted at 25 °C (77 °F) and/or

85 °C (185 °F) to increase accuracy for pH, ORP and conductivity.

Note: Refer to the probe documentation to find the temperature limits for the probe

that is used.

1. Put the probe and a reference thermometer in a container of water at

approximately 25 °C and allow the temperature to stabilize.

2. Compare the temperature read by the meter with that of the

reference thermometer. The difference is the adjustment value for

the meter.

Example: reference thermometer: 24.5 °C; meter: 24.3 °C.

Adjustment value: 0.2 °C.

3. Enter the adjustment value for the 25 °C reading:

a. Push . The parameter flashes.

b. Use the arrow keys to select tEn.

c. Push . 25 °C is shown.

d. Push and then use the arrow keys to enter the adjustment

value for 25 °C. Push . 85 °C is shown.

4. Put the probe and a reference thermometer in a container of water at

approximately 85 °C and allow the temperature to stabilize.

5. Compare the temperature from the meter with that of the reference

thermometer. The difference is the adjustment value for the meter.

6. Push and then use the arrow keys to enter the adjustment value

for the 85 °C reading. Push .

About sample measurements

Each probe has specific preparation steps and procedures for taking

sample measurements. For step-by-step instructions, refer to the

documents that are included with the probe.

12

English

Push to take a sample measurement. During measurements, the

parameter flashes and the timer shows the stabilization time. To change

the measurement parameter (if applicable), push and hold .

To measure the sample continuously, push

2 times. The parameter

flashes to indicate the continuous measurement mode.

Change the temperature units

The temperature units can be changed when the measurement screen is

shown.

1. Make sure that a stable measurement reading is shown.

2. Push

and at the same time. The temperature units change to °C

or °F.

Disable the auto-shutoff option

The meter is set to automatically power off after 5 minutes of inactivity to

maximize the battery life. This option can be temporarily disabled.

1. Make sure that the meter is powered off.

2. Push and hold until the display shows OFF and no. The power

remains on indefinitely.

3. To power off the meter, push and hold until the display shows

OFF.

Note: The auto-shutoff option is enabled again when the meter is powered on

normally.

Set the backlight time

The display is illuminated when

is pushed. The user can set the

length of time that the backlight stays on.

Note: The battery life is decreased when the backlight time is increased.

1. Make sure that the instrument is powered on.

2. Push and immediately push 2 times. The backlight time

flashes.

3. Push or to change the backlight time (range: 3 seconds to

2 minutes).

Data logger

Set the date and time

Each data point is saved with the time and date of the measurement.

1. From the standby screen, push .

2. When the display shows rt, push . The display shows dAt and the

date (DD-MM-YY).

3. When the values flash, use the arrow keys to set the current year,

month and day. After the date is set, the display shows tin and the

time (HH:MM:SS).

4. When the values flash, use the arrow keys to set the current hour,

minute and second.

Save data manually

To save data manually, push when a measurement is complete or at

any time during a continuous measurement. The display shows DL and

OK each time a data point is saved.

Save data automatically

When the instrument is set to measure continuously, data can be saved

at regular time intervals.

1. From the standby screen, push

.

2. When the display shows Fr, push . The display shows Fr and

OFF.

3. Push . The time interval in HH:MM:SS is shown.

4. Use the arrow keys to set the interval when data will be automatically

saved (range: 5 s to 1 min 30 s).

5. Start a continuous measurement. Data will be saved at the specified

interval. The display shows DL and OK each time a data point is

saved.

English

13

View data

A data point includes the measurement value(s) and the time and date of

the measurement. Data points are saved with a related number. The

most recent data point has the highest number.

Note: For calibration data, refer to View the calibration data on page 12.

1. From the standby screen, push . The display shows DL and the

number of the most recent data point. The screen changes to show

the value of the data and the related time and date.

2. Use the arrow keys to see other data points.

3. To exit the datalog, push .

Erase data

N O T I C E

Data will be erased permanently. Make sure to save the data to a computer first,

then erase the data in the instrument.

All of the data in the instrument datalog can be erased. Individual data

points cannot be erased.

1. From the standby screen, push .

2. When the display shows CLr dL, push . CLr flashes.

3. Push to erase all of the data in the instrument datalog.

Data transfer

Setup for data transfer

Data can be sent from the instrument to a computer through wireless

transmission. The portCom application and the USB-RF device must be

installed on the computer.

1. Install portCom and the USB-RF device driver. Refer to Figure 10.

During the driver installation, select the option to install from a

specific location: C:\Program Files\portCom.

2. Open portCom. Use the Setup menu to change one of the options:

Option Description

Decimal Changes the decimal type (. ,)

Language Changes the language of the user interface

Figure 10 Install portCom and the USB-RF driver

Send data to a computer

Data that is saved in the datalog can be sent to a computer and then

saved to a user-specified location. A spreadsheet application can be

used to view the data.

1. Put the USB-RF device into a USB port.

Note: The USB-RF device must be used even when the computer has wireless

capability.

2. Open portCom.

3. Push 2 times. The display shows Snd. The newest data is shown

on the top row in the portCom window. Refer to Figure 11.

Note: All of the data in the instrument datalog is sent to the computer.

4. Click Save.

14

English

5. Select a folder location and give the data set a file name.

6. Select the type of file (.txt or .csv), then click Save.

Figure 11 Send data to a computer

Maintenance

Clean the instrument

N O T I C E

Never use cleaning agents such as turpentine, acetone or similar products to

clean the instrument including the display and accessories.

N O T I C E

Make sure that all meter connectors stay dry. Use a dry towel to remove liquid

from the connectors.

Clean the exterior of the instrument with a moist cloth and a mild soap

solution.

Store the instrument

W A R N I N G

Explosion hazard. Expired batteries can cause hydrogen gas buildup

inside the instrument. Replace the batteries before they expire and do

not store the instrument for long periods with the batteries installed.

N O T I C E

To avoid potential damage to the meter from battery leakage, remove the meter

batteries prior to extended periods of non-use.

Replace the batteries

W A R N I N G

Explosion hazard. Incorrect battery installation can cause the release of explosive

gases. Be sure that the batteries are of the same approved chemical type and

are inserted in the correct orientation. Do not mix new and used batteries.

English 15

For battery replacement, refer to Figure 12. Make sure that the cover is

tightly closed to maintain the IP67 enclosure rating.

Figure 12 Battery replacement

Troubleshooting

Refer to the following table for common problem messages or

symptoms, possible causes and corrective actions.

Error/Warning Description Solution

Measurement out

of range.

• Insert the probe into the appropriate

standard and read again.

• Clean the probe and the membrane.

• Make sure that there are no air

bubbles in the membrane.

• Disconnect the probe and then

connect the probe again.

• Connect a different probe to verify if

problem is with probe or meter.

Battery is low. Insert new batteries.

E1 Unstable reading

during a stability

measurement or

during calibration.

Make sure that the probe is properly

immersed in the sample.

E2 Probe current:

exceeded upper

limit during

measurement ≥

250 nA.

• Clean the probe and the membrane.

• Make sure that there are no air

bubbles in the membrane.

• Disconnect the probe and then

connect the probe again.

• Connect a different probe to verify if

problem is with probe or meter.

E2 pH probes

sensitivity out of

range (accepted

values 70–105%).

• Make sure that the correct probe is

connected to the meter.

• Connect a new probe.

16 English

Error/Warning Description Solution

E2 During calibration,

the difference

between the

constants gets >

30%.

• Insert the probe into the appropriate

standard and read again.

• Clean the probe and the membrane.

• Make sure that there are no air

bubbles in the membrane.

• Disconnect the probe and then

connect the probe again.

• Connect a different probe to verify if

problem is with probe or meter.

• Connect a new probe.

E3 During calibration,

the cell constant

gets < 0.05 cm

-1

.

• Insert the probe into the appropriate

standard and read again.

• Clean the probe and the membrane.

• Make sure that there are no air

bubbles in the membrane.

• Disconnect the probe and then

connect the probe again.

• Connect a different probe to verify if

problem is with probe or meter.

E3 Slope out of range

(accepted values ±

58 mV).

Connect a new probe.

E4 Buffer solution not

recognized.

• Clean the probe and the membrane.

• Make sure that there are no air

bubbles in the membrane.

• Disconnect the probe and then

connect the probe again.

• Connect a different probe to verify if

problem is with probe or meter.

• Make sure that the buffer used

matches the buffer specified in

configuration.

• Replace the buffer solution.

• Make sure of the temperature

specification in configuration.

Error/Warning Description Solution

E4 Salinity cannot be

calculated TC=0

Modify TC

E5 Same buffer

solutions.

• Clean the probe and the membrane.

• Make sure that there are no air

bubbles in the membrane.

• Disconnect the probe and then

connect the probe again.

• Connect a different probe to verify if

problem is with probe or meter.

• Make sure that the buffer used

matches the buffer specified in

configuration.

• Replace the buffer solution.

• Make sure of the temperature

specification in configuration.

E6 The calibration

solutions have

different

temperatures.

Make sure that the calibration solutions

have the same temperature.

ErA (only

MM156)

Salinity is set to

automatic and

measured value >

50 g/L.

Modify TC

E7 The datalog is

empty.

Save data to the datalog.

E8 The datalog is full. Erase data from the datalog.

E9 The data transfer

failed.

Make sure that the USB-RF device is

installed and that portCom is open.

Replacement parts and accessories

Note: Product and Article numbers may vary for some selling regions. Contact the

appropriate distributor or refer to the company website for contact information.

English

17

Replacement parts

Description Item no.

Batteries, Alkaline AA 1938004

Carrying case LZW9990.99

Accessories

Description Item no.

Wireless data transfer kit (portCom software with USB-RF

device)

LZW2598.99.0002

Electrolyte for DO probe 51 20, 25 mL LZW9811.99

Electrolyte for DO probe 51 30, 50 ml 2759126

Tube for DO probe calibration LZW5123.99

Service kit for 51 30 DO probe (contains 2 membrane

modules and DO filling solution)

5196800

Replacement DO membrane for DO probe 51 20 LZW5125.99

147 μS/cm standard solution (at 25 °C, 77 °F), 125 mL

bottle

LZW9701.99

1413 μS/cm standard solution (at 25 °C, 77 °F), 125 mL

bottle

LZW9711.99

12.88 mS/cm standard solution (at 25 °C, 77 °F), 125 mL

bottle

LZW9721.99

Set of calibration tubes, 147 μS/cm, 1413 μS/cm and

12.88 mS/cm

LZW9138.99

220 mV standard solution, 125 mL LZW9402.99

Buffer solution pH 4.01, 125 mL LZW9460.99

Buffer solution pH 7.00, 125 mL LZW9461.97

Buffer solution pH 10.01, 125 mL LZW9470.99

Electrolyte solution, KCI 3M, 50 mL LZW9509.99

Accessories (continued)

Description Item no.

Calibration tubes pH 4.01, pH 7.00 and pH 10.01 LZW9137.97

Tube for ORP standard calibration 220 mV LZW9136.99

Work protector for electrodes 50 51 T and 50 52 T LZW9162.99

Standard solutions

Technical buffer solutions (DIN 19267)

Refer to Table 1 pH and ORP (mV) values of specific buffer sets at

varying temperatures.

Table 1 pH, ORP (mV) and temperature values

Temperature pH mV

°C °F

0 32 2.01 4.01 7.12 9.52 10.30 —

10 50 2.01 4.00 7.06 9.38 10.17 245

20 68 2.00 4.00 7.02 9.26 10.06 228

25 77 2.00 4.01 7.00 9.21 10.01 220

30 86 2.00 4.01 6.99 9.16 9.96 212

40 104 2.00 4.03 6.97 9.06 9.88 195

50 122 2.00 4.06 6.97 8.99 9.82 178

60 140 2.00 4.10 6.98 8.93 9.76 160

70 158 2.01 4.16 7.00 8.88 — —

80 176 2.01 4.22 7.04 8.83 — —

90 194 2.01 4.30 7.09 8.79 — —

Conductivity standard solutions

Refer to Table 2 for conductivity values of standard solutions at varying

temperatures.

18

English

Table 2 Conductivity and temperature values

Temperature Conductivity (EC)

°C °F µS/cm µS/cm mS/cm mS/cm

15.0 59 119 1147 10.48 92.5

16.0 60.8 122 1173 10.72 94.4

17.0 62.6 125 1199 10.95 96.3

18.0 64.4 127 1225 11.19 98.2

19.0 66.2 130 1251 11.43 100.1

20.0 68 133 1278 11.67 102.1

21.0 69.8 136 1305 11.91 104.0

22.0 71.6 139 1332 12.15 105.4

23.0 73.4 142 1359 12.39 107.9

24.0 75.2 145 1386 12.64 109.8

25.0 77 147 1413 12.88 111.8

26.0 78.8 150 1440 13.13 113.8

27.0 80.6 153 1467 13.37 115.7

28.0 82.4 156 1494 13.62 —

29.0 84.2 159 1522 13.87 —

30.0 86 162 1549 14.12 —

31.0 87.8 165 1581 14.37 —

32.0 89.6 168 1609 14.62 —

33.0 91.4 171 1638 14.88 —

34.0 93.2 174 1667 15.13 —

35.0 95 177 1696 15.39 —

Salinity values for dissolved oxygen meters

Table 3 can be used to convert conductivity values to salinity for

dissolved oxygen meters.

Table 3 Conversion from conductivity to salinity

Conductivity (mS/cm) Salinity (g/L NaCl)

1.9 1.0

3.7 2.0

7.3 4.0

10.9 6.0

17.8 10.1

25.8 15.1

33.6 20.2

41.2 25.4

48.9 30.6

56.3 35.8

62.2 40.0

69.4 45.3

75.7 50.0

English 19

Inhaltsverzeichnis

Technische Daten auf Seite 20

Allgemeine Informationen auf Seite 21

Installation auf Seite 23

Benutzeroberfläche und Navigation auf Seite 24

Inbetriebnahme auf Seite 27

Durchführung einer Messung auf Seite 27

Datenlogger auf Seite 31

Datenübertragung auf Seite 32

Wartung auf Seite 33

Fehlerbehebung auf Seite 34

Ersatzteile und Zubehör auf Seite 37

Standardlösungen auf Seite 38

Salinitätswerte für DO-Messgeräte auf Seite 39

Technische Daten

Änderungen vorbehalten.

Technische Daten Details

Abmessungen 18,6 x 7,3 x 3,8 cm (7,32 x 2,87 x 1,5 Zoll)

Gewicht 300 g (0,66 lb)

Gerätegehäuse IP67

Spannungsversorgung

(intern)

Alkalibatterien (AA/LR6) oder aufladbare

Nickelmetallhydrid-Akkus (NiMH) (3);

Lebensdauer des Akkus: mehr als 500 Stunden

Eingangsanschlüsse MP-5- oder MP-8-Anschluss für sensION+-

Sonden

Schutzklasse des

Messgerätes

Class III

Lagertemperatur –15 bis +65 °C

Betriebstemperatur 0 bis 50 °C (32 bis 122 °F)

Technische Daten Details

Luftfeuchtigkeit bei Betrieb maximal 80% (nicht-kondensierend)

Datalog Maximal 500 Datenpunkte, automatische oder

manuelle Speicherung

Wireless-Datenübertragung USB-RF-Gerät, maximale Einsatzentfernung

10 m

HF-Ausgangsleistung HF-Dongle: -16,01 dBm (Toleranz von -4 bis

+2 dBm)

Geräte: -4,01 dBm (Toleranz von -4 bis +2 dBm)

Messbereich pH: –2,00 bis 19,99; ORP: ±1999 mV

Leitfähigkeit: 0,01 bis 500 mS/cm; TDS: 0 bis

500 g/L; Salzgehalt: 0,0 bis 1999 mg/L, 2,0 bis

50,0 g/L

DO: 0,00 bis 19,99 mg/L und 20,0 bis 22,0 mg/L

(25 °C), 0,0 bis 199,9% und 200 bis 250%

(25 °C)

Auflösung pH: 0,01 pH; ORP: 1 mV (0,1 mV von –199.9 bis

199,9 mV)

DO: 0,1% (1% wenn ≥ 200%); 0,01 mg/L

(0,1 mg/L wenn ≥ 20 mg/L)

Leitfähigkeit: ändert sich mit Bereich

(automatische Bereichseinstellung)

Temperatur: 0,1 °C (0,1 °F)

Messfehler (± 1 Stelle) pH: ≤ 0,01 pH; ORP: ≤ 1 mV

DO: ≤ 0,5 % des gemessenen Werts

Leitfähigkeit: ≤ 0,5 % (0,01 µS/cm bis

19,99 mS/cm); ≤ 1 % (≥ 20,0 mS).

Salzgehalt/TDS: ≤ 0,5 %

Temperatur: ≤ 0,2 °C (≤ 0,4 °F)

20 Deutsch

Stránka sa načítava ...

Hach sensION+ DL Používateľská príručka

Hach sensION+ DL Používateľská príručka

V iných jazykoch

Súvisiace články

Ďalšie dokumenty