Hach TitraLab KF1121 Basic User Manual

DOC022.98.93082

TitraLab

®

KF1000 series

workstations

03/2019, Edition 9

Basic User Manual

Allgemeines Benutzerhandbuch

Manuale di base per l'utente

Manuel d'utilisation de base

Manual básico del usuario

Manual básico do utilizador

Základní uživatelská příručka

Grundlæggende brugervejledning

Basisgebruikershandleiding

Podstawowa instrukcja obsługi

Allmän användarhandbok

Peruskäyttöohje

Основно ръководство за потребителя

Alapvető felhasználói kézikönyv

Manual de utilizare de bază

Temel Kullanıcı Kılavuzu

Základný návod na použitie

Osnovni uporabniški priročnik

Osnovni korisnički priručnik

Βασικό εγχειρίδιο χρήσης

English..............................................................................................................................3

Deutsch.......................................................................................................................... 27

Italiano............................................................................................................................ 53

Français......................................................................................................................... 79

Español........................................................................................................................ 105

Português.................................................................................................................... 131

Čeština......................................................................................................................... 157

Dansk............................................................................................................................182

Nederlands................................................................................................................. 207

Polski............................................................................................................................ 233

Svenska....................................................................................................................... 259

Suomi............................................................................................................................284

български................................................................................................................... 308

Magyar......................................................................................................................... 334

Română....................................................................................................................... 360

Türkçe...........................................................................................................................386

Slovenský jazyk......................................................................................................... 410

Slovenski..................................................................................................................... 435

Hrvatski........................................................................................................................ 459

Ελληνικά...................................................................................................................... 483

2

Table of contents

Specifications on page 3 Startup on page 18

General information on page 3 Standard operations on page 19

Installation on page 7 Maintenance on page 25

Keypad on page 16

Expanded manual version

For additional information, refer to the expanded version of this manual, which is available on the

manufacturer's website.

Specifications

Specifications are subject to change without notice.

Specification Details

Dimensions (W x D x H) 22 x 40 x 36 cm (8.7 x 15.7 x 14.2 in.)

Weight 4 kg (8.8 lb)

Power requirements 100–240 VAC, 50/60 Hz

Altitude 2,000 m (6,562 ft) maximum

Operating temperature 15 to 35 °C (59 to 95 °F)

Relative humidity 20 to 80%, non-condensing

Storage temperature –5 to 40 °C (23 to 104 °F)

Installation category II

Pollution degree 2

Certifications Safety IEC/EN 61010-1; EMC IEC/EN 61326-1

EMC requirements This product is intended to be used in a domestic or

basic electromagnetic environment

Warranty 1 year (EU: 2 years)

General information

In no event will the manufacturer be liable for direct, indirect, special, incidental or consequential

damages resulting from any defect or omission in this manual. The manufacturer reserves the right to

make changes in this manual and the products it describes at any time, without notice or obligation.

Revised editions are found on the manufacturer’s website.

Safety information

N O T I C E

The manufacturer is not responsible for any damages due to misapplication or misuse of this product including,

without limitation, direct, incidental and consequential damages, and disclaims such damages to the full extent

permitted under applicable law. The user is solely responsible to identify critical application risks and install

appropriate mechanisms to protect processes during a possible equipment malfunction.

Please read this entire manual before unpacking, setting up or operating this equipment. Pay

attention to all danger and caution statements. Failure to do so could result in serious injury to the

operator or damage to the equipment.

English

3

Make sure that the protection provided by this equipment is not impaired. Do not use or install this

equipment in any manner other than that specified in this manual.

Use of hazard information

D A N G E R

Indicates a potentially or imminently hazardous situation which, if not avoided, will result in death or serious injury.

W A R N I N G

Indicates a potentially or imminently hazardous situation which, if not avoided, could result in death or serious

injury.

C A U T I O N

Indicates a potentially hazardous situation that may result in minor or moderate injury.

N O T I C E

Indicates a situation which, if not avoided, may cause damage to the instrument. Information that requires special

emphasis.

Precautionary labels

Read all labels and tags attached to the instrument. Personal injury or damage to the instrument

could occur if not observed. A symbol on the instrument is referenced in the manual with a

precautionary statement.

This symbol, if noted on the instrument, references the instruction manual for operation and/or safety

information.

This symbol indicates that a risk of electrical shock and/or electrocution exists.

This symbol indicates the presence of devices sensitive to Electro-static Discharge (ESD) and

indicates that care must be taken to prevent damage with the equipment.

Electrical equipment marked with this symbol may not be disposed of in European domestic or public

disposal systems. Return old or end-of-life equipment to the manufacturer for disposal at no charge to

the user.

Certification

C A U T I O N

This equipment is not intended for use in residential environments and may not provide adequate protection to

radio reception in such environments.

Canadian Radio Interference-Causing Equipment Regulation, IECS-003, Class A:

Supporting test records reside with the manufacturer.

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing

Equipment Regulations.

Cet appareil numérique de classe A répond à toutes les exigences de la réglementation canadienne

sur les équipements provoquant des interférences.

FCC Part 15, Class "A" Limits

Supporting test records reside with the manufacturer. The device complies with Part 15 of the FCC

Rules. Operation is subject to the following conditions:

4

English

1. The equipment may not cause harmful interference.

2. The equipment must accept any interference received, including interference that may cause

undesired operation.

Changes or modifications to this equipment not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment. This equipment has been tested

and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference, in which case the user will be required to

correct the interference at their expense. The following techniques can be used to reduce

interference problems:

1. Disconnect the equipment from its power source to verify that it is or is not the source of the

interference.

2. If the equipment is connected to the same outlet as the device experiencing interference, connect

the equipment to a different outlet.

3. Move the equipment away from the device receiving the interference.

4. Reposition the receiving antenna for the device receiving the interference.

5. Try combinations of the above.

Product overview

The instrument operates with digital and analog sensors. Measurement applications are installed on

the instrument to automate the measurement process. Instructions show on the display when user

intervention is required.

1 Keypad 6 Syringe protection cover 11 Pump 2 input/output (waste)

2 Display 7 Syringe input/output 12 Pump 1 input/output (solvent)

3 USB port

1

8 Tube clips 13 Pump access cover

4 Sample stopper 9 Syringe

5 Beaker 10 Sensor holder

1

A second USB port is found on the rear of the instrument, but the instrument recognizes only

one USB storage device connection at a time.

English 5

Table 1 Instrument configuration

Model Syringes Pumps

KF1121 1 2

Instrument connections

Use the USB port on the side of the instrument for the USB applications key supplied with the

instrument. Use the USB port on the rear of the instrument to connect to a printer, mouse, keyboard

or a USB hub.

1 24 V external power supply port 4 Not used 7 USB port

2 Sensor 1 port 5 Not used 8 Ethernet port

3 Sensor 2 port 6 Serial port

Product components

Make sure that all components have been received. Refer to the packing list in the box. If any items

are missing or damaged, contact the manufacturer or a sales representative immediately.

Figure 1 Contents of the instrument box

6 English

Note: For identification, the outlet tube from the syringe is fitted with a blue marker.

1 Instrument 3 Power cord

2 Sample stopper 4 Power supply

Figure 2 Contents of the application box

1 KF standard beaker 6 Syringe holding ring

2 KF white PTFE conical adapter 7 Syringe

3 Magnetic stir bars 8 Glass bottle

4 USB applications key 9 Bottle caps (3 x GL45)

5 Sensor 10 Desiccant cartridges (3x, filled with a molecular

sieve)

Installation

C A U T I O N

Multiple hazards. Only qualified personnel must conduct the tasks described in this section of the

document.

N O T I C E

This is a class A product. There may be potential difficulties in ensuring electromagnetic compatibility in other

environments, due to conducted as well as radiated disturbances. In a domestic environment this product may

cause radio interference in which case the user may be required to take adequate measures.

N O T I C E

Network and access point security is the responsibility of the customer that uses the wireless instrument. The

manufacturer will not be liable for any damages, inclusive however not limited to indirect, special, consequential

or incidental damages, that have been caused by a gap in, or breach of network security.

Installation guidelines

• This instrument is for indoor use only.

English

7

• The power supply connector on the rear panel must be easily accessible so the power can be

disconnected quickly in case of emergency.

• Keep the instrument away from temperature extremes, including heaters, direct sunlight and other

heat sources.

• Put the instrument on a stable and level surface in a well ventilated place.

• Make sure that there is at least 15 cm (6 in.) of space on all sides of the instrument to prevent

electrical parts from overheating.

• Do not operate or keep the instrument in dusty, damp or wet locations.

• Always keep the surface of the instrument and all accessories dry and clean.

Connect to AC power

D A N G E R

Electrocution hazard. If this equipment is used outdoors or in potentially wet locations, a Ground Fault

Circuit Interrupt (GFCI/GFI) device must be used for connecting the equipment to its main power

source.

C A U T I O N

Electrical shock and fire hazards. Make sure that the supplied cord and non‐locking plug meet the

applicable country code requirements.

W A R N I N G

Fire hazard. Use only the external power supply that is specified for this instrument.

1. Connect the power cord to the power supply.

2. Connect the power supply to the instrument (refer to Instrument connections on page 6).

3. Connect the power cord to an electrical outlet.

Install the syringe

Before syringe installation, set the instrument power to on. Push the power button on the front of the

instrument. Make sure that the startup sequence shows on the display. The syringe holder lowers to

its operating position.

Note: Ignore any warning messages related to missing applications that show on the display.

The sensor holder has two positions: one over the magnetic stirrer and the second at 180° to the

right. Move the sensor holder away from the instrument to the second position.

Refer to the illustrated steps that follow.

C A U T I O N

In step 6, tighten the syringe using the metallic part at the top. Do not hold the glass section of the syringe. Do not

tighten too much.

8 English

English 9

Install the sensor holder accessories

Add the stir bar to the beaker, and then attach the beaker to the sensor holder. Install the desiccant

cartridge and the sample stopper. Refer to the illustrated steps that follow.

Prepare the tubes

Remove any bends in the end of the tubes.

10

English

Connect the tubes

Arrow symbols identify the inlet and outlet ports for the syringe and the pump connections. The “up”

arrow is the outlet port. The “down” arrow is the inlet port. Turn the tube connectors on the inlet and

outlet ports of the syringe and pump until they click.

The suction tube that drains into the waste bottle must be installed on the bottom of the beaker for

good drainage.

N O T I C E

The diffusion tip and tube holder on the outlet tube, are pre-installed at the optimal positions. Do not change the

position of the diffusion tip or the tube holder.

Install the sensor

Connect the sensor

Use a conical adapter to hold the sensor tightly in the sensor holder. Make sure the conical adapter

is installed correctly. This makes sure of a secure water-tight fitting in the sensor holder and the tip of

the sensor will be in the correct position in the beaker.

Connect the sensor to an available sensor port on the rear of the instrument. After the sensor is

connected, make sure that the sensor icon shows in the banner at the top of the display.

English

11

Refer to the illustrated steps that follow.

Check the titrant tube and sensor installation

The titrant must be added where there is most turbulence and as far away from the sensor to allow

the reagent time to react. Check that the titrant tube and the sensor are positioned correctly. Refer to

Figure 3, where the arrows show the direction of the sample flow.

12

English

Figure 3 Titrant tube and sensor positions

1 Titrant tube 2 Sensor 3 Magnetic stir bar

Install the titrant and the reagent

C A U T I O N

Chemical exposure hazard. Obey laboratory safety procedures and wear all of the personal protective

equipment appropriate to the chemicals that are handled. Refer to the current safety data sheets

(MSDS/SDS) for safety protocols.

Put a filled desiccant cartridge into the adapter on the titrant and solvent bottle caps.

Note: The molecular sieve in the filled cartridges must be regenerated regularly depending on the humidity of the

laboratory. Refer to Regenerate the molecular sieve on page 25.

Loosen the tube connector on the bottle cap. Push the inlet tube through the connector. Make sure

that the end of the tube is at the bottom of the bottle. Tighten the connector on the bottle cap.

Pump 1 is used to fill the measurement cell with solvent. Pump 2 is used to empty the measurement

cell. Refer to the illustrated steps that follow.

English

13

14 English

Figure 4 Bottles identification

1 Titrant 3 Solvent

2 Waste

Tidy the work area

Attach the tubes to the instrument with the clips on the electrovalve and the sensor holder. Refer to

the illustrated steps that follow.

English 15

User interface and navigation

Keypad

1 Power 3 Selection keys 5 Home key

2 Printer 4 Navigation keys

Key Description

Power Sets the instrument power to on or off. Push the key for 2 seconds to set the power to off.

Printer The printer key only operates if a printer is connected to the instrument. Sends the data

currently shown on the display to a connected printer when pushed. A sound is heard if the

current display cannot be printed. A graph is automatically printed at the end of the

measurement, if the option is selected (Settings > Options).

Selection keys

(contextual)

Used to select options shown above them in the footer bar. The options available are

applicable to the current operation (e.g. calibration, measurement, etc.).

Navigation keys Scrolls through menus and data, enter numbers and letters, enter checkbox settings and set

options for the syringe and the pump.

Home Push this key at any time to go directly to the home screen. A sound is heard if the key is

disabled (e.g. during a calibration or measurement).

16 English

Home screen

1 Available options from this screen 5 Screen name

2 A second row of available options from this screen 6 Information icons (refer to Table 2)

3 KF applications 7 Option available by pushing the selection key below

4 Screen icon 8 Arrow keys available for use in the screen

Table 2 shows the information icons that can be shown in the header bar.

Table 2 Information icons

Icon Description

A printer is connected to the instrument

A USB key is connected to the instrument

A sensor is connected to sensor port 1

A sensor is connected to sensor port 2

The data log file is full. Refer to Manage the data log on page 24 for the options available to manage the

data log file.

English 17

Startup

C A U T I O N

Chemical exposure hazard. Obey laboratory safety procedures and wear all of the personal protective

equipment appropriate to the chemicals that are handled. Refer to the current safety data sheets

(MSDS/SDS) for safety protocols.

C A U T I O N

Personal injury hazard. Never use the instrument without the syringe cover installed.

Configure the instrument

1. From the main menu, select Settings.

2. Select an option, then push Select.

Option Description

Applications Changes, makes copies, exports and removes application data. Make sure that the

duplication function does not make more than five applications.

Operators Adds, changes and removes operators.

Date + Time Sets the instrument date and time.

Brightness Sets the brightness of the display.

Sounds Sets the sound options.

Language Sets the language.

Network Give a name to the instrument. If a printer is connected, this name is printed on the hard-

copy output. Restart the instrument if the name is changed.

Info Shows information about the instrument and the attached hardware.

Restore Defaults Sets the instrument to the default configuration.

Options Sets the application parameters view to expert mode. When the instrument is set to off,

sets the syringe to empty into the titrant bottle. Changes the temperature display unit. Set

the cell standby parameter (refer to Cell standby on page 18). Prints the measurement

and derivative curves if a printer is connected. Specify if a balance is connected.

Security Change the password and specify which options are password protected.

3. Push Back.

Cell standby

Make sure that the measurement cell is prepared before selecting an application, because the cell

standby starts automatically.

Cell standby dries the measurement cell automatically using a regulated addition of the titrant as

defined in the application. When the cell standby option is active:

• Cell standby starts automatically as soon as an application is selected from the home screen

• The stirring speed is the speed specified for the application

• Cell standby information is shown at the bottom of the application start screen

• After the weight of the sample is validated at the end of the measurement procedure, the cell

conditioning automatically starts again

• Cell standby continues until the next sample is selected and a new measurement procedure starts

• If the Cell management option is selected at the end of the measurement procedure, cell standby

is paused and starts again when the cell management procedure completes

18

English

• The measurement procedure starts when Start is selected. If the cell is dry, cell conditioning is not

needed and the user is asked to add the sample. If the cell is not dry, cell conditioning starts

Install the applications

Use the supplied USB key to install the applications. The instrument can install a maximum of five

applications. The installed applications are shown on the top line of the display.

1. Push Home to go to the main menu.

2. Connect the USB key to the USB port on the side of the instrument. The applications on the USB

key show on the display.

3. Push the arrow keys to highlight and select an application to install. Push the left or right arrow

key to select it. Do this step again to select additional applications to install.

4. Push Import to install the selected applications.

5. Push OK to complete the installation. The installed applications show on the home screen.

Note: To install more applications, push Home to go to the home screen, then remove the USB key and

reconnect it.

Prepare the instrument for measurement

1. From the home screen, select Purge. All attached devices are listed.

2. Select All elements to purge all the attached devices, or select one device to purge. Push

Select. Air is removed from the device and filled with liquid from the bottle.

3. Push OK when the operation has completed.

4. Make sure that there are no air bubbles in the device. Do step 2 again if there are any air

bubbles.

5. Select the next device to purge if individual devices are being selected.

6. Push Exit when all the tubes are filled with reagent and the device has no air bubbles.

Note: If a few small air bubbles can be seen on the inner wall and/or piston of the syringe, they can be left

without effecting system performance.

Standard operations

C A U T I O N

Multiple hazards. Only qualified personnel must conduct the tasks described in this section of the

document.

C A U T I O N

Chemical exposure hazard. Obey laboratory safety procedures and wear all of the personal protective

equipment appropriate to the chemicals that are handled. Refer to the current safety data sheets

(MSDS/SDS) for safety protocols.

C A U T I O N

Personal injury hazard. Never use the instrument without the syringe protection cover in place.

C A U T I O N

Chemical exposure hazard. Never remove the stir bar from the beaker before the end of a titration.

English 19

Calibration

Calibrate the titrant

1. Make sure that the glass beaker, the sensor holder and all related parts are clean and dry. Put a

magnetic stir bar into the beaker.

2. Attach the beaker to the sensor holder. Make sure that the beaker fits tightly into the sensor

holder.

3. Read the related "Application Note" from the USB applications key for more instructions.

4. Fill the beaker with the applicable amount of solvent. Refer to the application note and Cell

management on page 25 to adapt the volume where applicable. Make sure that there is no

liquid spill. Make sure that the initial level is enough so that the sensor is correctly installed in the

sample. Do not put too much solvent in the beaker.

5. From the home screen, select Calibration.

6. If more than one application contains a titrant calibration method, push the up and down arrow

keys to highlight the application to use, then push Select.

7. Calibration information shows on the display. If necessary, select an icon for more information or

to change some data.

Option Description

Information Shows more information about the calibration.

Operator Changes the operator ID. Select from a list of applicable operators.

8. Make sure that the icon at the bottom of the display is highlighted. Do the instructions that

show on the display adjacent to this icon. Make sure that the tubes and sensor are correctly

aligned.

9. Push Start to start the calibration. Calibration data shows on the display.

10. If the default stirring speed needs to be adjusted, push the up and down arrow keys to increase or

decrease the speed.

Note: This adjustment only applies to the current operation. The standard default stirring speed for the

application is not changed.

11. The cell drift threshold, stability bar, sample temperature and measurement duration are shown at

the bottom of the display. The stability bar shows the stability of the signal and ranges in color

from red (unstable), through yellow, to green (stable). The cell drift value is shown in the middle of

the display. These messages can be displayed under the cell drift value:

Message Description

Excess of water The measurement cell contains too much water. Titrant continues to be added until

the cell is dry.

Excess of titrant The measurement cell contains too much titrant. No more titrant is added.

Risk of cell overflow The measurement cell is full and there is a risk of liquid spill. The procedure stops.

Note: The stability bar or these messages are displayed at the bottom of the display during the calibration

procedure.

12. Two options are available during the cell conditioning procedure:

Option Description

Stop Aborts the measurement and no results are calculated. If selected during the Replicate Sample

option, then all data in the series is lost.

Skip Stops the cell conditioning and goes directly to the next step in the procedure. Results are then

calculated from measurement data available before Skip is selected. Results can be less accurate

using this option.

13. Weigh the standard in its container and write down the result.

20

English

Stránka sa načítava ...

Hach TitraLab KF1121 Basic User Manual

Táto príručka je tiež vhodná pre

Hach TitraLab KF1121 Basic User Manual

V iných jazykoch

Súvisiace články

Ďalšie dokumenty