Parkside 95929 Translation Of Original Operation Manual

IAN 95929

ANGLE GRINDER PWS 230 A1

WINKELSCHLEIFER

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung

ANGLE GRINDER

Operation and Safety Notes

Translation of original operation manual

SAR OK CSISZOLÓ

Kezelési és biztonsági utalások

Az originál használati utasítás fordítása

KOTNI BRUSILNIK

Navodila za upravljanje in varnostna opozorila

Prevod originalnega navodila za uporabo

ÚHLOVÁ BRUSKA

Pokyny pro obsluhu a bezpečnostní pokyny

Překlad originálního provozního návodu

UHLOVÁ BRÚSKA

Pokyny pre obsluhu a bezpečnostné pokyny

Preklad originálneho návodu na obsluhu

GB Operation and Safety Notes Page 5

HU Kezelési és biztonsági utalások Oldal 19

SI Navodila za upravljanje in varnostna opozorila Stran 35

CZ Pokyny pro obsluhu a bezpečnostní pokyny Strana 49

SK Pokyny pre obsluhu a bezpečnostné pokyny Strana 63

DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 77

Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the

device.

Olvasás előtt kattintson az ábrákat tartalmazó mindkét oldalra és végezetül ismerje meg a készülék minde-

gyik funkcióját.

Pred branjem obe strani s slikami odprite navzven in se nato seznanite z vsemi funkcijami naprave.

Před čtením si odklopte obě dvě strany s obrázky a potom se seznamte se všemi funkcemi přístroje.

Pred čítaním si odklopte obidve strany s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich anschließend

mit allen Funktionen des Gerätes vertraut.

A B

4

2

6

3

11

12

5

7

1

4

8 9 10

E

C

19

F

14

15

16

13

0

1

G

3

17

D

18

12

5 GB

Table of contents

Introduction

Proper use ............................................................................................................................................Page 6

Features and equipment .....................................................................................................................Page 6

Included items .....................................................................................................................................Page 6

Technical information .......................................................................................................................... Page 6

General power tool safety warnings

1. Work area safety............................................................................................................................Page 7

2. Electrical safety ............................................................................................................................... Page 7

3. Personal safety ................................................................................................................................Page 7

4. Power tool use and care ................................................................................................................Page 8

5. Service .............................................................................................................................................Page 8

Safety advice for all uses ....................................................................................................................Page 8

Safety advice relating to kickback .....................................................................................................Page 10

Special safety advice relating to grinding and disc-cutting ..............................................................Page 10

Further special safety advice for disc-cutting ..................................................................................... Page 11

Special safety advice for abrading using sandpaper ......................................................................Page 11

Special safety advice for polishing ....................................................................................................Page 11

Special safety advice for working with wire brushes ........................................................................Page 11

Safety advice for angle grinders ........................................................................................................Page 12

Advice on use ......................................................................................................................................Page 13

Preparing for use

Attaching the disc guard cover using the quick-release fastener .....................................................Page 14

Attaching the auxiliary handle ...........................................................................................................Page 14

Attaching and replacing roughing / grinding / cutting discs ............................................................Page 14

Operation

Switching on and off ........................................................................................................................... Page 15

Maintenance and cleaning ............................................................................................... Page 15

Service ...............................................................................................................................................Page 16

Warranty .........................................................................................................................................Page 16

Disposal ............................................................................................................................................Page 16

Declaration of Conformity / Manufacturer..........................................................Page 17

6 GB

Introduction / General power tool safety warnings

Introduction

Angle grinder PWS 230 A1

Q

Introduction

We congratulate you on the purchase of

your new

device. You have chosen a

high quality product. The

instructions for use are part of the product. They

contain important information concerning safety,

use and disposal. Before using the product, please

familiarise yourself with all of the safety information

and instructions for use. Only use the unit as descri-

bed and for the speciﬁed applications. If you pass

the product on to anyone else, please ensure that

you also pass on all the documentation with it.

Q

Proper use

This tool is suitable for cutting, roughing and brush-

ing metal materials without the use of water. Any

other use or modiﬁcation to the device shall be

considered as improper use and could give rise to

considerable dangers. We will not accept liability

for loss or damage arising from improper use. The

device is not intended for commercial use.

Note: Slots cut in load-bearing walls must comply

with standard DIN 1053 Part 1 or the regulations

applicable in your country.

These instructions and advice must be observed.

Before you start a task, seek the advice of a com-

petent structural engineer, architect, or the relevant

site management staﬀ.

Q

Features and equipment

1

Hand grip (rotatable)

2

ON / OFF switch

3

Safety lock-out

4

Unlocking button

5

Carbon brushes cover

6

Auxiliary handle

7

Disc guard cover

8

Clamping lever

9

Coded projection

10

Adjuster screw

11

Spindle lock button

12

Threaded hole (3 x) for auxiliary handle

13

Clamping nut (see Fig. F)

14

Mounting spindle (see Fig. F)

15

Mounting ﬂange (see Fig. F)

16

Coded groove (see Fig. F)

17

Spanner

18

Roughing / grinding disk*

19

Cutting disc for metal* (see Fig. E)

* not included

Q

Included items

1 Angle grinder PWS 230 A1

1 Auxiliary handle

1 Disc guard cover

1 Spanner

1 Operating instructions

Q

Technical information

Rated voltage: 230–240 V

~

50 Hz

Rated power consumption: 2000 W

Rated speed: n 6500 min

-1

Grinding disc: Ø 230 mm

Mounting spindle: M14 / threaded

Protection class: II /

Noise and vibration data:

Measured values for noise are determined in accor-

dance with EN 60745. The A-weighted noise level

of the electrical power tool are typically:

Sound pressure level: 96.8 dB(A)

Sound power level: 107.8 dB(A)

Uncertainty K: 3 dB

Wear ear protection!

Evaluated acceleration, typical:

Hand / arm vibration a

h

= 10.075 m / s

2

Uncertainty K = 1.5 m / s

2

The vibration level speciﬁed in

these instructions was measured in accordance with

an EN 60745 standardised measurement process

7 GB

Introduction / General power tool safety warnings

Introduction

and can be used to compare equipment. The vibra-

tion emission value speciﬁed can also serve as a

preliminary assessment of the exposure.

The vibration level will change according to the ap-

plication of the electrical tool an in some cases may

exceed the value speciﬁed in these instructions.

Regularly using the electric tool in such a way may

make it easy to underestimate the vibration.

Note: If you wish to make an accurate assessment

of the vibration loads experienced during a particular

period of working, you should also take into account

the intervening periods of time when the device is

switched oﬀ or is running but is not actually in use.

This can result in a much lower vibration load over

the whole of the period of working.

General power tool

safety warnings

Read all safety warnings

and all instructions. Failure to follow the warn-

ings and instructions may result in electric shock, ﬁre

and / or serious injury.

Save all warnings and instructions for

future reference.

The term “power tool” in the warnings refers to your

mains-operated (corded) power tool or battery-op-

erated (cordless) power tool.

1. Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) D

o not operate power tools in explosive

atmospheres, such as in the presence

of flammable liquids, gases or dust.

Power tools create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders away

while operating a power tool. Distractio

ns

can cause you to lose control.

2. Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way. Do

not use any adapter plugs with earthed

(grounded) power tools. Unmodiﬁed plug

s

and matching outlets will reduce risk of electric

shock.

b) Avoid body contact with earthed or

grounded surfaces, such as pipes,

radiators, ranges and refrigerators.

There is an increased risk of electric shock if

your body is earthed or grounded.

c) Do not expose power tools to rain or

wet conditions. Water entering a power tool

will increase the risk of electric shock.

d) Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging

the power tool. Keep cord away from

heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk

of electric shock.

e)

When operating a power tool outdo

ors,

use an extension cord suitable for out-

door use. Use of a cord suitable for outdoor

use reduces the risk of electric shock.

f) If operating a power tool in a damp

location is unavoidable, use a residual

current device (RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3. Personal safety

a) Stay alert, watch what you are doing

and use common sense when operat-

ing a power tool. Do not use a power

tool while you are tired or under the

influence of drugs, alcohol or medica-

tion. A moment of inattention while operating

power tools may result in serious personal injury.

b) Use personal protective equipment.

Always wear eye protection. Protective

equipment such as dust mask, non-skid safety

shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal in-

juries.

8 GB

c) Prevent unintentional starting. Ensure

the switch is in the off-position before

connecting to power source and / or

battery pack, picking up or carrying

the tool. Carrying power tools with your ﬁng

er

o

n the switch or energising power tools that hav

e

the switch on invites accidents.

d) Remove any adjusting key or wrench

before turning the power tool on. A

wrench or a key left attached to a rotating part

of the power tool may result in personal injury.

e) Do not overreach. Keep proper foot-

ing and balance at all times. This enables

better control of the power tool in unexpected

situations.

f) Dress properly. Do not wear loose

clothing or jewellery. Keep your hair,

clothing and gloves away from mov-

ing parts. Loose clothes, jewellery or long

hair can be caught in moving parts.

g) If devices are provided for the connec-

tion of dust extraction and collection

facilities, ensure these are connected

and properly used. Use of dust collection

can reduce dust-related hazards.

4. Power tool use and care

a) Do not force the power tool. Use the

correct power tool for your applica

tion.

The correct power tool will do the job better

and safer at the rate for which it was designed.

b) Do not use the power tool if the switch

does not turn it on and off. Any power

tool that cannot be controlled with the switch is

dangerous and must be repaired.

c) Disconnect the plug from the power

source and / or the battery pack from

the power tool before making any ad-

justments, changing accessories, or

storing power tools. Such preventive safety

measures reduce the risk of starting the power

tool accidentally.

d) Store idle power tools out of the reach

of children and do not allow persons

unfamiliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the hands of un-

trained users.

e) Maintain power tools. Check for mis-

alignment or binding of moving parts,

breakage of parts and any other con-

dition that may affect the power tool’s

operation. If damaged, have the power

tool repaired before use. Many accidents

are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are

easier to control.

g) Use the power tool, accessories and

tool bits etc. in accordance with these

instructions, taking into account the

working conditions and the work to

be performed. Use of the power tool for

operations diﬀerent from those intended could

result in a hazardous situation.

5. Service

a) Have your power tool serviced by a

qualified repair person using only

iden-

tical replacement parts. This will ensure

that the safety of the power tool is maintained.

Q

Safety advice for all uses

General safety advice for grinding,

sanding (with sandpaper), wire brushing,

polishing and disc-cutting:

a) This electrical power tool is intended

for use as a grinding, sanding, wire-

brushing, and disc-cutting machine.

Observe all the safety advice, instruc-

tions, information in figures and all

other information you received with

this device. If you do not observe the follow-

ing advice it could lead to electric shock, ﬁre

and / or serious injury.

b) Normative statement / advice for this tool is not

applicable.

General power tool safety warnings

9 GB

c) Do not use any accessory not specifi-

cally intended by the manufacturer

for this electrical power tool. Although

an accessory may ﬁt on your electrical power

tool, this does not on its own guarantee that it

can be safely used.

d) The maximum permitted speed of an

attachment must be at least as high as

the maximum speed indicated for the

electrical power tool. An accessory rotating

faster than its permitted speed could disintegrate

or ﬂy oﬀ.

e) The external diameter and the thickness

of the attachment must be compatible

with the dimensions of your electrical

power tool. Attachments that are not dimen-

sionally compatible cannot be adequately

guarded or controlled.

f) Grinding discs, flanges, grinding

wheels or other accessories must fit

exactly on to the spindle of your elec-

trical power tool. Attachments that do not

exactly ﬁt on the spindle turn unevenly, vibrate

severely and could lead to loss of control.

g) Do not use damaged attachments.

Before every use check attachments

such as grinding discs for loose frag-

ments and cracks, grinding wheels for

cracks, deterioration or excessive

wear and wire brushes for loose or

broken wires. If the electrical power

tool or attachment is dropped, inspect

for damage or change the attachment

for an undamaged one. When you

have inspected and inserted the at-

tachment, position yourself and by-

standers away from the plane of the

rotating attachment and run the device

at maximum speed for one minute.

Damaged attachments will usually break apart

during this test.

h) Wear personal protective equipment.

Use a full face visor, safety goggles or

safety glasses, depending on the ap-

plication. Wear a dust mask, hearing

protectors, safety gloves or special

apron capable of stopping particles of

the grinding medium or workpiece,

as appropriate for the task. Eyes must

be protected from the ﬂying debris which can

arise from some operations. Dust or breathing

masks must be capable of ﬁltering out the dust

generated by the application. Prolonged expo-

sure to loud noise can lead to hearing loss.

i) Keep bystanders at a safe distance

from your work area. Anyone entering

the work area must wear personal

protective equipment. Fragments of the

workpiece or of a broken attachment could ﬂy

oﬀ and cause injury beyond the immediate

working area.

j) Hold the device by the insulated han-

dle surfaces when you are undertak-

ing work where there is the danger

of the attachment striking hidden

electricity cables or the device’s mains

lead. Contact with a live wire could cause

metal parts of the device to become live and

lead to electric shock.

k) Keep the mains lead away from rotat-

ing attachments. If you lose control of the

device the mains lead may become severed or

trapped and your hand or arm may be pulled

into the rotating attachment.

l) Never lay the electrical power tool

down until after the attachment has

come to a complete standstill. The rotat-

ing attachment may snag when it comes into

contact with the surface and cause you to lose

control of the device.

m) Do not have the electrical power tool

running while you are carrying it. Your

clothing could become trapped by unintention-

al contact with the rotating attachment and the

tool could be pulled into your body.

n) Clean the ventilation slots on your

electrical power tool regularly. The mo-

tor’s fan draws dust into the housing. A build-up

of metal dust could give rise to an electrical

hazard.

o) Never use the electrical power tool

near inflammable materials. Sparks

could ignite these materials.

General power tool safety warnings

10 GB

p) Do not use attachments that require

the use of coolants. The use of water or

other liquid coolants could result in electric shock.

Q

Safety advice

relating to kickback

Kickback is the sudden reaction to a pinched or

snagged rotating attachment, such as a grinding

disc, grinding pad, wire brush etc. Pinching or

snagging results in the rotating attachment coming

to an abrupt stop. This causes the electrical power

tool (if not controlled) to move in the opposite di-

rection to the direction of rotation of the attachment

at the point of constraint.

If, for example, a grinding disc is pinched or snags

in a workpiece, this can cause the edge of the

grinding disc to penetrate the workpiece, become

trapped there and either free itself or kickback. The

grinding disc moves towards or away from the op-

erator, depending on the direction of movement of

the disc at the point of constraint. The grinding disc

could also break.

Kickback occurs as a result of incorrect use or mis-

use of the electrical power tool. It can be prevented

by taking the appropriate precautions as described

below.

a) Maintain a firm grip on the electrical

power tool and position your body

and arms to allow you to resist kick-

back forces. Always use the auxiliary

handle, if provided, to exercise the

greatest possible control over kick-

back forces or reaction torques as the

device builds up to full speed. By taking

suitable precautions the operator can control

kickback and reaction forces.

b) Do not place your hands near a rotat-

ing attachment. If kickback occurs the at-

tachment could move over your hand.

c) Avoid positioning your body in the

area into which the electrical power

tool would move in the event of a

kickback. A kickback moves the electrical

power tool in the opposite direction to the di-

rection of movement of the grinding disc at the

point of constraint.

d) Work particularly carefully in the

area of corners, sharp edges etc. to

avoid the attachment bouncing or

snagging on the workpiece. Corners,

sharp edges or bouncing have a tendency to

snag the rotating attachment. This causes loss

of control or kickback.

e) Do not use saw-chain woodcarving

discs or toothed discs. Such attachments

create frequent kickback and loss of control of

the electrical power tool.

Q

Special safety advice relating

to grinding and disc-cutting

a) Always use the guard designed for the

type of abrasive consumable you are

using. Always use abrasive consuma-

bles approved for use with your elec-

trical power tool. Abrasive consumables not

approved for use with your electrical power tool

cannot be adequately guarded and are unsafe.

b) To ensure the highest level of opera-

tional safety, the disc guard cover must

be attached to the electrical power tool

and set in such a way that the smallest

possible area of the abrasive consum-

able is exposed to the operator. The disc

guard cover is there to protect the operator

from pieces breaking oﬀ and accidental con-

tact with the abrasive consumable.

c) Abrasive consumables must be used

only for their recommended purposes,

For example: never grind with the side

face of a cutting disc. Cutting discs are in-

tended for removing material using the edge

of the disc. Sideways forces on these abrasive

consumables can cause them to break.

d) Always use an undamaged mounting

flange of the correct size and shape

for your selected grinding disc. Suitable

ﬂanges support the grinding disc and reduce

General power tool safety warnings

11 GB

the chance of it breaking. Flanges for cutting

discs are diﬀerent from the ﬂanges for other

abrasive discs.

e) Never use worn down abrasive con-

sumables intended for larger electrical

power tools. Abrasive consumables intended

for larger electrical power tools are not designed

for the faster rotational speeds of these smaller

electrical power tools and could break.

Q

Further special safety

advice for disc-cutting

a) Avoid snagging the cutting disc and

do not use too much contact pressure.

Do not attempt to make excessively

deep cuts. Overloading the cutting disc in-

creases the load and the tendency of the disc

to twist or snag in the cut, making kickback or

disc breakage more likely.

b) Avoid the area in front of or behind

the rotating cutting disc. If the cutting disc

is moving away from you at the point of con-

straint in the workpiece, then, in the event of

a kickback, the electrical power tool and the

rotating disc may be thrown towards you.

c) If the cutting disc jams or you stop

work for a while, switch the device

off and hold it until the disc comes to

a complete stop. Never attempt to

pull the still rotating cutting disc out of

the cut as this could cause kickback.

Determine and rectify the reason for the jamming.

d) Do not switch on the device if the cut-

ting disc is in the workpiece. Allow

the cutting disc to reach full speed be-

fore carefully continuing with the cut.

Otherwise the disc could snag, jump out of the

workpiece or cause a kickback.

e) Support boards or workpieces whilst

cutting to reduce the risk of kickback

caused by a jammed cutting disc. Large

workpieces may bend under their own weight.

The workpiece must be supported to both sides

of the cutting disc and particularly near the

cutting disc and at the workpiece edge.

f) B

e particularly careful when pocket

cutting in existing walls or other areas

where you cannot see what you are cut

-

t

ing into. The cutting disc plunged into the surface

could cut through gas or water pipes, electricity

cables or other objects and cause kickback.

Q

Special safety advice for

abrading using sandpaper

Do not use over-sized sanding sheets.

Follow the manufacturer’s recommen-

dations for sanding sheet size. Sanding

sheets that project beyond the backing pad

could cause injury in addition to jamming,

tearing of the sheet or kickback.

Q

Special safety

advice for polishing

Do not use the polishing bonnet if it

has any loose parts, in particular the

fastening cords. Tuck the fastening cords

away or trim them. Loose fastening cords rotat-

ing with the attachment could catch your ﬁngers

or become trapped in the workpiece.

Q

Special safety advice for

working with wire brushes

a) Bear in mind that wire brushes lose

pieces of wire during normal use. Do

not overload the wires by applying too

much pressure. Flying pieces of wire can very

easily penetrate thin clothing and / or skin.

b) Use a guard, if recommended, but

make sure that the wire brush does

not come into contact with the guard.

The diameters of disc brushes and cup brushes

can increase due to contact pressure and cen-

tripetal forces.

General power tool safety warnings

12 GB

Q

Safety advice for angle grinders

DANGER OF ELECTRIC SHOCK! Do not

operate the device if the mains lead

or mains plug is damaged.

DANGER OF ELECTRIC SHOCK! Do not

touch the mains lead if it becomes

damaged or cut through while you

are using the device. Pull the plug out of

the mains socket immediately and have the de-

vice repaired by a suitably qualiﬁed person or

at your service centre.

DANGER OF ELECTRIC SHOCK! Do not

operate the device if it is damp and

do not use it in a damp environment.

DANGER OF ELECTRIC SHOCK! If you

use the device outdoors, always con

nect

it through a residual current device

(RCD) with a maximum trip current of

30 mA. If using an extension lead, always use

one that is approved for outdoor use.

Do not suspend or carry the device by

the mains lead. Always work with the

mains lead leading away from the

rear of the device. Otherwise the device

could be damaged.

Grinding discs must be carefully kept

and handled in accordance with the

manufacturer’s instructions. Otherwise

they could be damaged.

Make sure that abrasive consumables

and tools are attached in accordance

with the manufacturer’s instructions

and advice. Otherwise they could become

detached from the device and result in injury

and / or damage to property.

Ensure that any spacers supplied and

required for the use of certain abrasive

consumables and tools are installed.

Do not use separate reducing bushes

or adapters in order to make grinding

discs with a larger bore fit.

When using abrasive consumables

and tools with a threaded insert make

sure that the tread is long enough for

the spindle length. Otherwise the grinding

discs could become detached from the device

and result in injury and / or damage to property.

Do not allow the end of the spindle

to contact the base of the hole in the

abrasive consumable.

Do not work in areas where there may

be concealed electricity cables or gas

or water pipes. Use a suitable detector

or ask your local utility service pro-

viders. Contact with electricity cables can

lead to ﬁre or electric shock. Damaging a gas

pipe can lead to an explosion. Penetration of a

water pipe can lead to property damage or to

electric shock.

NOXIOUS FUMES!

Working with harmful / noxious dusts represents

a risk to the health of the person operating the

device and to anyone near the work area.

For longer periods of cutting or grind-

ing metal or stone materials which

give rise to dusts that are hazardous

to health, the device must be connected

to a suitable external dust extraction

device.

Ensure that there is adequate ventila-

tion when working on plastic, paint,

varnish etc.

Do not soak the materials or the sur-

face you are about to work on with

liquids containing solvents.

DANGER OF INJURY! Wear close-fitting

clothing and keep long hair inside a

hairnet or suitable headwear.

For safety reasons this device must

always be used with the auxiliary

handle

6

in place.

The adjustable disc guard cover

7

must

always be in place when working with

roughing, grinding or cutting discs.

Otherwise there could be danger of injury.

Use the vacuum dust extraction facility

if your work generates high amounts

of dust. Use suction devices particular-

ly approved for the purpose.

Use permitted consumables and tools

only. Check that the speed given on the

discs is greater or equal to the rated

speed of the device.

Take note of the direction of rotation

and always hold the device in such a

General power tool safety warnings

13 GB

way that the sparks and grinding de-

bris are thrown away from your body.

Otherwise there could be danger of injury.

Make sure that the dimensions of the

disc are suitable for the device and

that the disc is of a type that fits prop-

erly on to the mounting flange

15

.

Q

Advice on use

Note! Discs must be used only for their recom-

mended purposes, otherwise they could disintegrate,

become damaged or cause accidents.

Roughing:

Never use cutting discs for

roughing or grinding!

Move the angle grinder using even

pressure to and fro over the workpiece.

Hold the roughing or grinding disc at

a flat angle to the workpiece when

working on a soft material. Use a

slightly steeper angle for harder ma-

terials.

Disc-cutting:

Never use roughing or

grinding discs for cutting!

Only use certified fibre-reinforced cut-

ting or grinding discs approved for use at

circumferential speeds of not less than 80 m / s.

CAUTION! The disc continues to rotate after

the device has been switched oﬀ. Do not at-

tempt to slow it down by pressing on the side

of the disc.

Securely support the workpiece. Use

clamps or a vice to grip the workpiece ﬁrmly.

This is much safer than holding it in your hand.

Switch the device off and allow it to

come to a complete standstill before

you put it down.

Unlock the ON / OFF switch immedi-

ately if a power failure occurs or the

plug is pulled out of the mains socket.

Place the switch in the OFF position.

This prevents the device from being inadvertent-

ly started up again.

Use the device for dry cutting or dry

grinding only.

The auxiliary handle

6

must be in

place

whenever the device is being used.

Do not work on materials containing

asbestos. Asbestos is a known carcinogen.

A tip! Using the device safely.

DANGER! Always guide

the device through the

workpiece against the di-

rection of rotation of the

disc. If you work in the other direction there is

the risk of kickback. The device may be forced

out of the cut.

Always switch on the device before

placing it against the workpiece. After

cutting or grinding, always lift the device from

the workpiece before switching it oﬀ.

When working always hold the device

securely with both hands (see Fig. D).

Always keep proper footing and balance.

For the best grinding performance move the

device evenly to and fro over the workpiece

maintaining an angle of 15° to 30° (between

grinding disc and workpiece).

When working on inclined surfaces do

not press the device hard down on to

the workpiece. If the speed slows greatly,

use less pressure. This will allow you to work

more eﬀectively and safely. If the device sudden-

ly stops due to it becoming retarded or trapped,

pull the mains plug from the socket immediately.

Cutting: Advance the device at an

appropriate rate. Do not incline the

cutting disc.

Roughing, grinding and cutting discs

get hot during use – allow them to

cool fully before touching them.

Never use the device for a purpose

for which it was not intended.

Before you insert the mains plug into

the socket, always check that the de-

vice is switched off.

General power tool safety warnings

14 GB

If a dangerous situation arises, pull

the mains plug immediately out of the

mains socket. Ensure that the device and

the mains plug are easily accessible and can

be reached quickly in an emergency.

When taking a break from your

work, before carrying out any tasks

on the device itself and when you are

not using the device, always pull the

mains plug out of the mains socket.

Always keep the device clean, dry and free of

oil or grease.

Remain alert at all times! Always watch

what you are doing and proceed with

caution. Do not use the device if you cannot

concentrate or you are feeling unwell.

Q

Preparing for use

Q

Attaching the disc guard cover

using the quick-release fastener

DANGER OF INJURY!

Pull the mains plug out of the mains

socket before you carry out any task

on the device.

DANGER OF INJURY! Always use the

angle grinder with the disc guard

cover in place. The disc guard cover must

be securely attached to the angle grinder. To

ensure the highest level of safety while using

the device, ensure that the smallest possible

area of the grinding or cutting tool is exposed

to the operator at all times. The disc guard cov-

er is there to protect the operator from pieces

breaking oﬀ and accidental contact with the

grinding or cutting tool.

DANGER OF INJURY! Ensure that the

guard

7

is attached so that its edge

is beyond the angle of the auxiliary

handle

6

(see Fig. B). Otherwise you

could injure yourself against the grinding or

cutting disc.

Open the clamping lever

8

.

Insert the disc cover guide

7

with the coded

projection

9

in the coded groove

16

.

Turn the disc guard cover

7

into the desired

position (working position). The closed side of

the disc guard cover

7

must always be facing

the operator.

Close the clamping lever

8

to ﬁrmly clamp

the disc guard cover

7

in place.

If necessary the clamping force of the connection

can be adjusted by tightening or loosening the

adjuster screw

10

.

Ensure that the disc guard cover

7

sits ﬁrmly

on the spindle collar.

Q

Attaching the auxiliary handle

CAUTION! For safety reasons this

device must always be used with the

auxiliary handle

6

in place. Otherwise

you could become injured.

DANGER OF INJURY!

Pull the mains plug out of the mains

socket before you carry out any task

on the device.

Screw the auxiliary handle

6

on the left, right

or on the top of the head of the device.

Q

Attaching and replacing

roughing / grinding / cutting discs

Take note of the dimensions of the roughing /

grinding or cutting discs. The circular hole must ﬁt

on to the mounting ﬂange without play. Do not use

a reducer piece or adapter.

DANGER OF INJURY!

Pull the mains plug out of the mains

socket before you carry out any task

on the device.

Check the condition of the roughing /

grinding or cutting discs. They must be

free of damage, moisture or cracks.

Otherwise they could break up during use and

cause injury.

DANGER OF BURNS! Always wear

protective gloves when changing a

roughing / grinding or cutting disc.

Roughing / grinding and cutting discs become

Preparing for use / Operation / Maintenance and cleaning

General power tool safety warnings / Preparing for use

15 GB

hot during use. Do not touch them until after

they have cooled down.

NOTE: Always ensure the discs are free of dirt

before use.

Use only abrasive consumables or tools with

an allowable speed at least as high as the

no-load speed of the device.

DANGER OF INJURY! Press the spindle lock

button

11

only after the mounting spindle

14

has reached a standstill.

Press the spindle lock button

11

to block the drive.

Release the clamping nut

13

using the spanner

17

(see Fig. C).

Place the roughing / grinding or cutting disc on

to the mounting ﬂange

15

with its labelled side

facing towards the device.

Then replace the clamping nut

13

, with its

raised side facing upwards, on to the mounting

spindle

14

.

Press the spindle lock button

11

to block the drive.

Tighten the clamping nut

13

again with the

spanner

17

.

NOTE: Replace a new disc immediately if it

runs unevenly or vibrates after being exchanged.

After replacing a disc let the device run under

no-load conditions for 30 seconds as a safety

check. Look out for unusual noises or generation

of sparks. Check that all the fastened-on parts

are correctly attached.

Pay attention to see that the arrow showing the

direction of rotation on the roughing / grinding

or cutting discs (including diamond cutting discs)

corresponds with the direction of rotation of the

device (see arrow on the head of the device).

Q

Operation

Q

Switching on and oﬀ

Note: Always switch on the angle grinder before

bringing it into contact with the workpiece material.

Switching on the device:

Press the safety lock-out

3

(see Fig. G).

Then press the ON / OFF switch

2

.

Switching oﬀ the device:

Release the ON / OFF switch

2

.

Rotating the hand grip:

DANGER OF INJURY!

Pull the mains plug out of the mains

socket before you carry out any task

on the device.

The hand grip

1

can be rotated by 90° to

the right or left (see Fig. A).

This allows the ON / OFF switch

2

to be

brought into the most comfortable position for

any working conditions.

Press the unlocking button

4

and rotate the

hand grip

1

to the right or left.

Make sure the hand grip

1

engages.

Q

Maintenance and cleaning

DANGER OF INJURY!

Pull the mains plug out of the mains

socket before you carry out any task

on the device.

Do not use sharp objects for cleaning

the device. Do not allow any liquids

to enter the device. Otherwise the device

could be damaged.

Have the carbon brushes replaced only at the

service centre or an accredited electrical

equipment repair centre. The device requires

no other maintenance.

Clean the device frequently; for best results do

this immediately after you have ﬁnished using it.

Use a dry cloth to clean the housing – under

no circumstances use petrol, solvents or cleaning

agents that attack plastic.

A vacuum cleaner is required to thoroughly

clean the device.

Ventilation openings must always be kept free.

Remove any adhering dust with a narrow paint

brush.

Preparing for use / Operation / Maintenance and cleaning

General power tool safety warnings / Preparing for use

16 GB

Q

Service

Have your device

repaired at the service centre or by

qualified specialist personnel using

original manufacturer parts only. This

will ensure that your device remains safe to use.

If the plug or lead needs

to be replaced, always have the

replacement carried out by the manu-

facturer or its service centre. This will

ensure that your device remains safe to use.

Q

Warranty

The warranty for this appliance is for 3 year

s

from the date of purchase. The appliance

has been manufactured with care and me-

ticulously examined before delivery. Please

retain your receipt as proof of purchase. In

the event of a warranty claim, please make

contact by telephone with our Service

Department. Only in this way can a post-

free despatch for your goods be assured.

The warranty covers only claims for material and

maufacturing defects, but not for transport damage,

for wearing parts or for damage to fragile components,

e.g. buttons or batteries. This product is for private use

only and is not intended for commercial use.

The warranty is void in the case of abusive and

improper handling, use of force and internal tam-

pering not carried out by our authorized service

branch. Your statutory rights are not restricted in

any way by this warranty.

The warranty period will not be extended by repairs

made unter warranty. This applies also to replaced

and repaired parts. Any damage and defects extant

on purchase must be reported immediately after

unpacking the appliance, at the latest, two days after

the purchase date. Repairs made after the expiration

of the warranty period are subject to payment.

GB

Service Great Britain

Tel.: 0871 5000 720

(0,10 GBP/Min.)

e-mail: kom[email protected]

IAN 95929

Q

Disposal

The packaging is wholly composed of

environmentally-friendly materials that can

be disposed of at a local recycling centre.

Do not dispose of electric tools

in the household waste!

In accordance with European Directive 2002 / 96 / EC

(covering waste electrical and electronic equipment)

and its transposition into national legislation, worn out

electrical power tools must be collected separately

and taken for environmentally compatible recycling.

Contact your local refuse disposal authority for more

details of how to dispose of your worn out electrical

devices.

Declaration of Conformity / Manufacturer

Service / Warranty / Disposal

17 GB

Q

Declaration of Conformity /

Manufacturer

We, KOMPERNASS HANDELS GMBH, the person

responsible for documents: Mr Semi Uguzlu, BURG-

STRASSE 21, 44867 BOCHUM, GERMANY, hereby

declare that this product complies with the following

standards, normative documents and EU directives:

Machinery Directive

(2006 / 42 / EC)

EU Low Voltage Directive

(2006 / 95 / EC)

Electromagnetic Compatibility

(2004 / 108 / EC)

RoHS Directive

(2011 / 65 / EU)

Applicable harmonized standards

EN 60745-1/A11:2010

EN 60745-2-3:2011

EN 55014-1/A1:2009

EN 55014-2/A2:2008

EN 61000-3-2/A2:2009

EN 61000-3-3:2008

Type / Device description:

Angle grinder PWS 230 A1

Date of manufacture (DOM): 12–2013

Serial number: IAN 95929

Bochum, 31.12.2013

Semi Uguzlu

- Quality Manager -

We reserve the right to make technical modiﬁca-

tions in the course of further development.

Declaration of Conformity / Manufacturer

Service / Warranty / Disposal

18

Tartalomjegyzék

19 HU

Tartalomjegyzék

Bevezetés

Rendeltetésszerű használat ...............................................................................................................Strona 20

Felszerelés ..........................................................................................................................................Strona 20

A szállítmány tartalma .......................................................................................................................Strona 20

Műszaki adatok .................................................................................................................................Strona 20

Elektromos szerszámokra vonatkozó általános

biztonsági tudnivalók

1. A munkahely biztonsága ..............................................................................................................Strona 21

2. Elektromos biztonsága ..................................................................................................................Strona 21

3. Személyek biztonsága ..................................................................................................................Strona 22

4. Az elektromos szerszámokkal való gondos járás és azok gondos használata ........................Strona 22

5. Szervíz ............................................................................................................................................Strona 23

Biztonsági tudnivalók minden alkalmazáshoz .................................................................................Strona 23

Visszarúgás és az arra vonatkozó biztonsági tudnivalók ...............................................................Strona 24

A csiszolásra és vágásra vonatkozó sajátos biztonsági tudnivalók ...............................................Strona 25

A vágótárcsákkal való munkákra vonatkozó további biztonsági tudnivalók ................................Strona 25

Csiszolópapírral való munkákra vonatkozó sajátos biztonsági tudnivalók ...................................Strona 26

A polírozásra vonatkozó sajátos biztonsági tudnivalók .................................................................Strona 26

A drótkefével való munkákra vonatkozó sajátos biztonsági tudnivalók ........................................Strona 26

Sarokcsiszolókra vonatkozó biztonsági tudnivalók .........................................................................Strona 26

A munkára vonatkozó utalások ........................................................................................................Strona 27

Üzembevétel

A védőburkolatnak a gyorszárral való felszerelése ........................................................................Strona 28

A pótfogantyú felszerelése ................................................................................................................Strona 29

Nagyoló- / vágótárcsa felszerelése / cseréje ...................................................................................Strona 29

Kezelés

Be- és kikapcsolás ..............................................................................................................................Strona 30

Karbantartás és tisztítás ...................................................................................................Strona 30

Szervíz ..............................................................................................................................................Strona 30

Garancia .........................................................................................................................................Strona 30

Mentesítés .....................................................................................................................................Strona 31

Konformitásnyilatkozat / Gyártó ..............................................................................Strona 31

Jótállási tájékoztató .............................................................................................................Strona 32

20 HU

Bevezetés / Elektromos szerszámokra vonatkozó általános biztonsági tudnivalók

Bevezetés

Sarokcsiszoló PWS 230 A1

Q

Bevezetés

Gratulálunk új készülékének vásárlása alkalmából.

Ezzel a döntésével vállalatunk értékes terméke mel-

lett döntött.

A használati utasítás ezen termék része. A

biztonságra, a használatára és a megsemmisítésre

vonatkozó fontos tudnivalókat tartalmazza. A termék

használata előtt ismerje meg az összes használati és

biztonsági tudnivalót. A terméket csak a leírtak sze-

rint és a megadott felhasználási területeken alkal-

mazza. A termék harmadik személy számára való

továbbadása esetén kézbesítse vele annak a teljes do-

kumentációját is.

Q

Rendeltetésszerű használat

A készülék fémek darabolására, nagyolására és

kefézésére alkalmas víz használata nélkül. Minden

másfajta alkalmazás, vagy a gép megváltoztatása

nem rendeltetésszerűnek számit és jelentős baleset-

veszélyeket rejt magában. A rendeltetésétől eltérő

alkalmazásból származó károkért nem állunk jót. A

készülék nem ipari alkalmazásra készült.

Utalás: A tartó falakban levő réseknek meg kell

felelni a DIN 1053 1. részének és az országspe-

ciﬁkus szabályozásoknak.

Ezeket az előírásokat feltétlenül be kell tartani. A

munka

megkezdése előtt kérjen tanácsot a felelős statikustól,

épitésztől, vagy az illetékes építésvezetéstől.

Q

Felszerelés

1

Készülékfogantyú (elforgatható)

2

BE- / KI-kapcsoló

3

Bekapcsolási retesz

4

Kireteszelő gomb

5

Szénkefék burkolata

6

Pótfogantyú

7

Védőburkolat

8

Feszítőkar

9

Vezető orr

10

Beállító csavar

11

Tengelyrögzítő gomb

12

Menetek (3 x) a pótfogantyú számára

13

Szorító anya (lásd a F ábrát)

14

Felfogó tengely (lásd a F ábrát)

15

Felfogó karima (lásd a F ábrát)

16

Vezető horony (lásd a F ábrát)

17

Szorító kulcs

18

Nagyoló tárcsa*

19

Vágótárcsa fémekhez* (lásd a E ábrát)

* nem részei a szállítmánynak

Q

A szállítmány tartalma

1 sarokcsiszoló PWS 230 A1

1 pótfogantyú

1 védőburkolat

1 szorító kulcs

1 kezelési utasítás

Q

Műszaki adatok

Névleges feszültség: 230–240 V∼ 50 Hz

Névleges teljesítmény: 2000 W

Mérési fordulatszám: n 6500 perc

-1

Csiszoló tárcsa: Ø 230 mm

Felfogó tengely: M14 / menet

Védettségi osztály: II /

Zaj- és rezgésinformációk:

A hangszint mért értékeit az EN 60745 szabvány-

nak megfelelően állapították meg. Az elektromos

szerszám A-kiemelés szerinti hangszintje tipikusan

a következő:

Hangnyomásszint: 96,8 dB(A)

Hangteljesítményszint: 107,8 dB(A)

Bizonytalansági tényező K: 3 dB

Viseljen hallásvédőt!

Értékelt gyorsulás, jellemző:

Kéz-kar-rezgé a

h

= 10,075 m / s

2

Bizonytalansági tényező K = 1,5 m / s

2

Stránka sa načítava ...

Parkside 95929 Translation Of Original Operation Manual

Táto príručka je tiež vhodná pre

Parkside 95929 Translation Of Original Operation Manual

V iných jazykoch

Súvisiace články

Ďalšie dokumenty