Parkside PWS 125 F6 Používateľská príručka

ANGLE GRINDER / WINKELSCHLEIFER /

MEULEUSE D’ANGLE PWS 125 F6

MEULEUSE D’ANGLE

Traduction des instructions d’origine

WINKELSCHLEIFER

Originalbetriebsanleitung

ANGLE GRINDER

Translation of the original instructions

ÚHLOVÁ BRUSKA

Překlad originálního provozního návodu

HAAKSE SLIJPER

Vertaling van de originele gebruiksaanwijzing

UHLOVÁ BRÚSKA

Preklad originálneho návodu na obsluhu

SZLIFIERKA KĄTOWA

Tłumaczenie oryginalnej instrukcji obsługi

AMOLADORA ANGULAR

Traducción del manual de instrucciones original

VINKELSLIBER

Oversættelse af den originale driftsvejledning

SMERIGLIATRICE ANGOLARE

Traduzione delle istruzioni d’uso originali

SAROKCSISZOLÓ

Az originál használati utasítás fordítása KOTNI BRUSILNIK

Prevod originalnega navodila za uporabo

IAN 392682_2201

GB / IE Translation of the original instructions Page 1

DE / AT / CH Originalbetriebsanleitung Seite 17

FR / BE Traduction des instructions d’origine Page 33

NL / BE Vertaling van de originele gebruiksaanwijzing Pagina 51

CZ Překlad originálního provozního návodu Strana 67

PL Tłumaczenie oryginalnej instrukcji obsługi Strona 83

SK Preklad originálneho návodu na obsluhu Strana 99

ES Traducción del manual de instrucciones original Página 115

DK Oversættelse af den originale driftsvejledning Side 131

IT Traduzione delle istruzioni d’uso originali Pagina 147

HU Az originál használati utasítás fordítása Oldal 163

SI Prevod originalnega navodila za uporabo Stran 179

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of

the device.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

Avant de lire le mode d‘emploi, ouvrez la page contenant les illustrations et familiarisez-vous ensuite avec

toutes les fonctions de l‘appareil.

Vouw vóór het lezen de pagina met de afbeeldingen open en maak u vertrouwd met alle functies van het

apparaat.

Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.

Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi

funkcjami urządzenia.

Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Antes de empezar a leer abra la página que contiene las imágenes y, en seguida, familiarícese con todas

las funciones del dispositivo.

Før du læser, vend siden med billeder frem og bliv bekendt med alle apparatets funktioner.

Prima di leggere aprire la pagina con le immagini e prendere conﬁdenza con le diverse funzioni

dell‘apparecchio.

Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik funkcióját.

Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.

A B

6a

C D



I

0

EF

PWS 125 F6 GB│IE │ 1 ■

Contents

Introduction ............................................................2

Intended use ........................................................................2

Features ...........................................................................2

Package contents ....................................................................3

Technical speciﬁcations ...............................................................3

General power tool safety warnings .......................................3

1. Work area safety ..................................................................4

2. Electrical safety ...................................................................4

3. Personal safety ....................................................................4

4. Power tool use and care ............................................................5

5. Service ..........................................................................5

Safety instructions for all applications ....................................................6

Kickback and corresponding safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Special safety instructions for grinding and abrasive cutting ...................................8

Additional special safety instructions for abrasive cutting .....................................8

Permissible accessories ................................................................9

Storage and handling of the recommended accessory tools ...................................9

Working procedures ..................................................................9

Operation ............................................................10

Fitting the protective cover for cutting ....................................................10

Mounting/adjusting the blade guard ....................................................11

Fitting the additional handle ...........................................................11

Fitting/changing the roughing/cutting disc ...............................................11

Switching on and oﬀ ................................................................12

Setting the rotational speed ...........................................................12

Maintenance and cleaning ...............................................13

Disposal ..............................................................13

Kompernass Handels GmbH warranty ....................................14

Service ............................................................... 15

Importer .............................................................15

Translation of the original Conformity Declaration ...........................16

PWS 125 F6

■ 2 │ GB│IE

ANGLE GRINDER PWS 125 F6

Introduction

Congratulations on the purchase of your new appli-

ance. You have chosen a high-quality product. The

operating instructions are part of this product. They

contain important information about safety, usage

and disposal. Before using the product, please

familiarise yourself with all of the operating and

safety instructions. Use the product only as de-

scribed and for the range of applications speciﬁed.

Please also pass these operating instructions on to

any future owner.

Intended use

The appliance is intended for the cutting and rough

cutting of metal materials, concrete and tiles without

the use of water. Any other usage or modiﬁcation

of the appliance is deemed to be improper and

carries a signiﬁcant risk of accidents. The manufac-

turer accepts no responsibility for damage resulting

from improper use. The appliance is not intended

for commercial use.

Explanation of the symbols used

Before using the appliance for the

ﬁrst time, read the original operating

instructions and safety instructions.

Using damaged cutting or roughing

discs is dangerous and may cause

serious injury!

 Diameter of the disc

Angle grinder

Wear protective goggles!

Wear ear muﬀs!

Wear safety shoes!

Wear protective gloves!

Wear a dust mask!

Not approved for wet grinding

Not approved for side grinding

Suitable for grinding metal

Features

Speed setting wheel

ON/OFF switch

Safety lock-out

Spare carbon brushes

Carbon brush cover

Additional handle

6a Tool holder for the two-hole assembly spanner

Blade guard

Mounting ring

Screws

Blade guard ﬁxture

Spindle locking button

Thread (3x) for additional handle

Clamping nut (see ﬁg. B)

Mounting spindle (see ﬁg. B)

Mounting ﬂange (see ﬁg. B)

Two-hole assembly spanner (see ﬁg. C)

Bulges

Plastic clip

Protective cover

PWS 125 F6 GB│IE │ 3 ■

Package contents

1 angle grinder

1 additional handle

1 blade guard

1 two-hole assembly spanner

1 cutting disc

2 spare carbon brushes

1 set of operating instructions

Technical speciﬁcations

Rated voltage 230 V ∼, 50 Hz (AC)

Rated power consumption 1200 W

Rated idle speed n 3000–12000 rpm

Disc size Ø 125 mm

Thread size M14

Protection class II / (double

insulation)

Noise and vibration data

Noise measurement value determined in accord-

ance with EN 60745. The A-rated noise level of

the power tool is typically as follows:

Noise emission value

Sound pressure level LPA = 87.5 dB (A)

Uncertainty K = 3 dB

Sound power level LWA = 98.5 dB (A)

Uncertainty K = 3 dB

Wear ear muﬀs!

Total vibration value

Surface grinding ah, AG = 3.086 m/s2

Uncertainty K = 1.5 m/s2

NOTE

► The vibration emission values and the noise

emission values given in these instructions

have been measured in accordance with a

standardised test procedure and can be

usedfor comparison of the power tool with

another tool.

► The speciﬁed total vibration values and noise

emission values can also be used to make a

provisional load estimate.

WARNING!

► Depending on the manner in which the

power tool is being used, and in particular

the kind of workpiece being worked, the

vibration and noise emission values can

deviate from the values given in these instruc-

tions during actual use of the power tool.

► Try to keep the vibration load as low as

possible. Measures to reduce the vibration

load are, e.g. wearing gloves and limiting

the working time. Wherein all states of oper-

ation must be included (e.g. times when the

power tool is switched oﬀ and times where

the power tool is switched on but running

without load).

General power tool

safety warnings

WARNING!

► Read all safety warnings and all instructions.

Failure to follow the warnings and instructions

may result in electric shock, ﬁre and/or serious

injury.

Save all warnings and instructions for future

reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-

operated (cordless) power tool.

PWS 125 F6

■ 4 │ GB│IE

1. Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmos-

pheres, such as in the presence of ﬂammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

2. Electrical safety

a) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiﬁed plugs and matching outlets

will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of elec-

tric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d)

Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

e)

When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduc-

es the risk of electric shock.

3. Personal safety

a) Stay alert, watch what you are doing and

use common sense when operating a power

tool. Do not use a power tool while you are

tired or under the inﬂuence of drugs, alcohol

or medication. A moment of inattention while

operating power tools may result in serious

personal injury.

b)

Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat,

or hearing protection used for appropriate condi-

tions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools

with your ﬁnger on the switch or energising

power tools that have the switch on invites acci-

dents.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool

may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use

of dust collection can reduce dust-related haz-

ards.

PWS 125 F6 GB│IE │ 5 ■

4. Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at

the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and oﬀ. Any power tool that can-

not be controlled with the switch is dangerous

and must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are dan-

gerous in the hands of untrained users.

e) Maintain power tools. Check for misalign-

ment or binding of moving parts, breakage of

parts and any other condition that may aﬀect

the power tool’s operation. If damaged, have

the power tool repaired before use.

Many accidents are caused by poorly main-

tained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed.

Use of the power tool for operations diﬀerent

from those intended could result in a hazardous

situation.

5. Service

a) Have your power tool serviced by a qualiﬁed

repair person using only identical replace-

ment parts. This will ensure that the safety of

the power tool is maintained.

b) Always arrange for the replacement of the

plug or the power cord to be carried out by

the manufacturer of the appliance or its cus-

tomer service department. This will ensure that

the safety of the power tool is maintained.

PWS 125 F6

■ 6 │ GB│IE

Safety instructions for all

applications

Special safety instructions for grinding and

abrasive cutting

a) This power tool is to be used as a grinder and

abrasive cutting appliance. Please follow all

safety instructions, instructions, diagrams and

data that you receive with the appliance.

Failure to follow the instructions below may

result in electric shock, ﬁre, and/or serious injury.

b) This power tool is not suitable for sandpaper

sanding, working with a steel brush or bur-

nishing. Using the power tool for applications

for which it is not designed can lead to hazards

and injuries.

c) Do not use any accessories that have not

been speciﬁcally provided or recommended

by the manufacturer for this power tool. Just

because you can attach the accessories to your

power tool, this does not guarantee that they

are safe to use.

d) The maximum speed of the accessory tool

used must be at least as high as the maximum

speed speciﬁed for the power tool. Accesso-

ries which rotate faster than the maximum per-

missible rate can break and throw pieces into

the air.

e) The external diameter and thickness of the

accessory tool used must correspond with

the dimensions of the power tool.

Incorrectly dimensioned accessory tools cannot

be suﬃciently shielded or controlled.

f) Accessory tools with a thread insert must

match the thread of the grinding spindle ex-

actly. For accessory tools that are mounted

using a ﬂange, the diameter of the hole on

the attachment tool must correspond to the

width of the ﬁtting on the ﬂange. Accessory

tools that cannot be ﬁrmly ﬁtted to the power

tool rotate unevenly, vibrate severely and can

lead to a loss of control.

g) Never use damaged accessory tools. Before

each use, check accessory tools such as

grinding discs for chips or cracks, grinding

plates for cracks, scuﬀs or excessive wear and

tear and wire brushes for loose or broken

wires. If the power tool or the accessory tool

in use is dropped, check to see whether it is

damaged or use an undamaged accessory

tool. When you have checked and inserted

the accessory tool, ensure that you and any

other people in the vicinity remain outside of

the level of the rotating accessory tool and

allow the tool to rotate at maximum speed for

one minute. Damaged accessory tools usually

break during the test period.

h) Wear personal protective equipment.

Depending on the application, ensure that

you use full face protection, eye protection

or goggles. As required, use a dust mask,

hearing protection, protective gloves or a

special apron that will protect you from

grinding and material particles. Protect your

eyes from ﬂying debris that may be produced

during certain applications. Dust or ﬁlter masks

must be used to ﬁlter any dust produced by the

application. If you are exposed to loud noise

for any length of time, you can suﬀer hearing

loss.

i) Ensure that other people remain at a safe

distance from your work area. Anyone who

enters the work area must wear personal

protective equipment.

Fragments of the workpiece or broken acces-

sory tools can ﬂy oﬀ and cause injury – even

outside the immediate work area.

PWS 125 F6 GB│IE │ 7 ■

j) Hold the power tool only by the insulated

handles when you are carrying out work

in which the accessory tool may come into

contact with concealed power cables or the

tool’s own power cord. Contact with a live ca-

ble can also make metal parts of the appliance

live, and could result in an electric shock.

k) Keep the power cord away from any rotating

accessories. If you lose control of the appli-

ance, the cord may be captured or cut and your

hand or arm could get caught in the rotating

accessory tool.

l) Never put the power tool down until the

accessory tool being used has come to a

complete standstill. The rotating accessory tool

could come into contact with the surface and

cause you to lose control of the power tool.

m) Do not leave the power tool running whilst

carrying it. Accidental contact between your

clothing and the rotating accessory tool could

lead to a physical injury.

n) Clean the ventilation slits of your power tool

regularly. The motor fan draws dust into the

housing and a strong accumulation of metal

dust can cause electrical hazards.

o) Never use the power tool in the vicinity of

inﬂammable materials. Sparks can ignite these

materials.

p) Do not use any accessory tools which require

liquid coolant. The use of water or other liquid

coolants may lead to electric shock.

Kickback and corresponding safety

instructions

Kickback is a sudden reaction caused when a

rotating accessory tool, e.g. grinding disc, grinding

plate, wire brush, etc., catches or jams. Catching or

jamming leads to an abrupt stop of the rotating ac-

cessory tool. If this happens, an uncontrolled pow-

er tool turns rapidly against the direction of rotation

of the accessory tool caught in the blockage.

If, for example, a grinding disc catches or jams, the

edge of the grinding disc that is projecting into the

workpiece can get caught and break oﬀ the grinding

disc or cause a kickback. The grinding disc can

then ﬂy in the direction of the operator or away from

him, depending on the direction of rotation of the

disc at the blockage. This can also break grinding

discs.

A kickback is caused by improper or incorrect use

of the power tool. This can be avoided by taking

proper precautions as given below.

a) Hold the power tool ﬁrmly in both hands and

position your body and arms so they can

absorb the force of A kickback. Always use the

auxiliary handle, if available, so that you have

the maximum possible control over the kick-

back force or reaction forces at full speed.

By taking adequate precautions, the operator can

stay in control of the kickback and reaction forces.

b) Never hold your hand close to a rotating

accessory tool. The accessory tool could jump

out of your hand if kickback occurs.

c) Avoid having any part of your body in the

region in which the power tool is likely to

move in event of a kickback. The kickback will

force the electrical tool in the opposite direction

to the direction of rotation of the grinding disc

at the blockage.

d) Take special care when working near corners,

sharp edges, etc. Do not allow the accessory

tool to bounce back from the workpiece or

jam. The rotating accessory tool is more likely to

jam in corners or sharp edges or if it bounces.

This can cause a loss of control or kickback.

e) Do not use chains or toothed saw blades.

Such accessories often cause a kickback or loss

of control over the power tool.

PWS 125 F6

■ 8 │ GB│IE

Special safety instructions for

grinding and abrasive cutting

a)

Use only the grinding accessories approved

for your power tool and the appropriate blade

guard for these grinding tools. Grinding tools

which are not designed for the power tool cannot

be suﬃciently shielded and are unsafe.

b)

Oﬀset grinding discs must be ﬁtted so that the

grinding surface does not protrude over the

edge of the blade guard. An improperly ﬁtted

grinding disc which protrudes over the edge of

the blade guard cannot be properly guarded.

c) The blade guard must be securely mounted

on the power tool and adjusted to ensure

maximum safety so that the smallest possible

amount of the grinding tool is exposed to

the operator. The blade guard is designed to

protect the operator from fragments, accidental

contact with the grinding tool and sparks that

could ignite clothing.

d) Grinding tools should only be used for the

recommended applications.

For example: never grind with the side sur-

face of a cutting disc. Cutting discs are de-

signed to remove material with the edge of the

disc. Any lateral application of force on these

grinding tools can lead to a breakage.

e) Always use an undamaged clamping ﬂange

of the correct size and shape for the selected

grinding disc. Suitable ﬂanges support the

grinding disc and reduce the risk of disc break-

age. Flanges for cutting discs can be diﬀerent to

ﬂanges for other grinding discs.

f) Do not use worn grinding discs from larger

power tools. Grinding discs for larger power

tools are not designed for the higher rotational

speeds of smaller power tools and can break.

Additional special safety instructions

for abrasive cutting

a) Avoid any blockage to the cutting disc or

excessive contact pressure. Do not make any

excessively deep cuts. Overloading the cutting

disc increases the stress and likelihood of jam-

ming or blocking and thus the possibility of a

kickback or a breakage of the grinding tool.

b) Avoid the area in front of and behind the

rotating cutting disc. When you move the cut-

ting disc away from yourself in the workpiece,

it is possible, in the event of a kickback, that

the electrical tool will be thrown out directly

towards you together with the rotating disc.

b) If the cutting disc jams or you stop working,

switch the tool oﬀ and hold it steadily in

the workpiece until the disc has completely

stopped turning. Never attempt to pull a ro-

tating cutting disc out of a cut. This could lead

to a kickback. Identify and remove the cause of

the jam.

d) Do not switch the power tool back on while

it is located in the workpiece. Allow the cut-

ting disc to reach its full speed before you

carefully continue the cut. Otherwise, the disc

can jam, jump out of the workpiece or cause a

kickback.

e) Support boards or large workpieces to re-

duce the risk of the cutting disc jamming and

causing a kickback. Large workpieces can

bend under their own weight. The workpiece

must be supported on both sides of the disc:

both in the vicinity of the cutting disc and also

at the edge.

f)

Be particularly careful when making pocket

cuts into existing walls or other obscured areas.

The inserted cutting disc may cut into gas or

water pipes, electrical wiring or other objects

that can cause a kickback.

PWS 125 F6 GB│IE │ 9 ■

Permissible accessories

Max. diameter Ø (mm)

Max. thickness (mm)

Thread size (mm)

Speed (rpm)

Circumferential speed

(m/s)

Tool

Protective cover

Cutting disc 125 3 M14 12200 80 Two-hole assembly

spanner Yes

Roughing disc 125 6 M14 12200 80 Two-hole assembly

spanner No

Storage and handling of the

recommended accessory tools

■ Grinding tools must be treated with care and

transported carefully.

■ Grinding tools should be stored in such a way

that they are not exposed to mechanical dam-

age or environmental inﬂuences (e.g. damp).

Working procedures

NOTE

► Grinding tools should only be used for the

recommended applications. Otherwise, they

can break, be damaged or cause injuries.

Rough grinding

Never use cutting discs

for rough grinding!

■Move the angle grinder with moderate

pressure back and forth over the workpiece.

■For soft material, move the roughing disc

at a ﬂat angle over the workpiece; for hard

material at a slightly steeper angle.

Abrasive cutting

Never use roughing discs

for cutting!

■Use only tested ﬁbre-reinforced cutting

or grinding discs that are approved for a

peripheral speed of not less than 80 m/s.

CAUTION!

► The grinder continues running after being

turned oﬀ. Do not try to brake it by applying

lateral counterpressure.

■Secure the workpiece.Use clamps/vices to

hold the workpiece ﬁrmly. This is much safer

than simply holding it in your hand.

■Always switch oﬀ the appliance before put-

ting it away and wait for the appliance to

come to a complete standstill.

■Release the ON/OFF switch immediately in

the event of a power failure or when the plug

is pulled out. Move it into the OFF position.

This prevents an uncontrolled restart.

■Use the appliance only for dry cutting or

sanding.

PWS 125 F6

■ 10 │ GB│IE

■The additional handle6 must be ﬁtted to the

appliance for all work.

■Materials containing asbestos may not be

processed. Asbestos is a known carcinogen.

Tip! This symbol indicates

proper behaviour.

DANGER! ALWAYS GUIDE THE

APPLIANCE THROUGH THE WORK-

PIECE IN REVERSE ROTATION.

► In the opposite direction there is a risk of

a kickback. The appliance can be pushed

out of the cut.

■Always switch the appliance on before apply-

ing it to the workpiece. After completing the

task, lift the appliance from the workpiece and

then switch it oﬀ.

■Always hold the appliance ﬁrmly with two

hands while working. Ensure that your stance

is secure and stable.

■ For an optimum grinding eﬀect, move the

appliance evenly at an angle of 15° to 30°

(between grinding disc and workpiece) back-

wards and forwards.

■When working on angled surfaces, do not

exert too much force on the workpiece. If the

rotational speed drops signiﬁcantly, you must

reduce the pressure exerted to allow safe and

eﬀective working. If the appliance suddenly

brakes completely or jams, it must be switched

oﬀ immediately.

■Cutting: Work at a moderate feed rate and

do not tilt the cutting disc.

■Roughing and cutting discs become very

hot – let them cool down completely before

touching them.

■Never use the appliance for purposes other

than the ones for which it was designed.

■Always make sure that the appliance is

turned oﬀ before plugging it into the wall

socket.

■In the event of danger, remove the mains plug

from the socket immediately. Ensure that the

appliance and the power socket are easily and

quickly accessible in the event of an emergency.

■Always remove the plug from the power socket

during work breaks, when adjusting the ap-

pliance and when it is no longer in use. The

appliance must be kept clean, dry and free of

oil and grease at all times.

■Remain alert at all times! Always pay attention

to what you are doing and act with common

sense. Do not use the appliance if you are dis-

tracted or feeling unwell.

WARNING!

Always wear safety goggles.

WARNING!

Always wear a dust mask!

Operation

Fitting the protective cover for cutting

When cutting with bonded abrasives, always use

the protective cover for cutting.

♦ Slide the protective cover onto the blade

guard (see ﬁg. F) until the plastic clip

snaps into place at the end.

♦ To remove the protective cover , pull the

plastic clip slightly forwards to release the

protective cover .

PWS 125 F6 GB│IE │ 11 ■

Mounting/adjusting the blade guard

WARNING! RISK OF INJURY!

► Always remove the plug from the power

socket before working on the appliance.

RISK OF INJURY!

► Always use the angle grinder with the blade

guard7. The blade guard should be in-

stalled securely. Set it so that the highest

possible degree of safety is achieved, i.e. the

smallest possible part of the grinding disc is

exposed to the operator. The blade guard7

is designed to protect the operator from frag-

ments and accidental contact with the

grinding tool.

► Make sure that the blade guard7 is ﬁtted

at least at the same angle as the additional

handle6 (see ﬁg. A). Otherwise, you could

cut injure yourself on the roughing disc or

cutting disc.

♦ Turn the blade guard7 to the required position

(working position). Make sure that the blade

guard7 is positioned in such a way that the

blade guard ﬁxture0 is lying over one of the

5 bulgesu on the blade guard7 (see ﬁg. E,

fold-out page).

♦ Ensure that the blade guard ﬁxture0 is ﬁrmly

seated in the respective bulgeu.

Fitting the additional handle

CAUTION!

► For safety reasons, this appliance may only

be used with the additional handle6.

Failure to do so can lead to serious injury.

The additional handle6 can be screwed

onto the left, the right or the top, depending

on the job at hand.

NOTE

► You can leave the tool holder 6a inserted

into the additional handle6 or remove it as

desired.

Fitting/changing the roughing/

cutting disc

Always wear protective gloves when changing

cutting/roughing discs. Roughing and cutting discs

become very hot. Allow them to cool down com-

pletely before touching them.

Pay attention to the dimensions of the roughing/

cutting disc. The diameter of the hole must ﬁt the

mounting ﬂange without any play. Do not use a

reducer or adapter.

■Check the roughing/cutting disc. It should not

be damaged or damp and have no cracks.

Otherwise, it could break during use and cause

injuries.

NOTE

► Use only discs which are free of dirt.

■ Use only grinding discs whose permissible

speed rating is at least as high as that on the

type plate on the power tool.

■RISK OF INJURY! Press the spindle locking

buttonq only when the mounting spindler is

at a complete standstill.

♦ Press the spindle locking buttonq to lock the

gearbox.

♦ Loosen the clamping nute using the two-hole

assembly keyz (see ﬁg. C).

♦ Place the rough grinding or cutting disc with the

label side towards the appliance on the mount-

ing ﬂanget.

♦ Then replace the clamping nute on the mount-

ing spindler with the raised side facing up.

PWS 125 F6

■ 12 │ GB│IE

With thin grinding discs (see ﬁg. 1):

♦ The collar of the clamping nute faces upwards

so that a thin grinding disc can be ﬁtted safely.

12

≤ 3,2 mm

Fig. 1

♦ Press the spindle locking buttonq to lock the

gearbox.

♦ Tighten the clamping nute using the two-hole

assembly spannerz.

With thick grinding discs (see ﬁg. 2):

> 3,2 mm

Fig. 2

The collar of the clamping nute points down-

wards, so that the thick grinding wheel can be

securely mounted on the mounting spindler.

♦ Lock the mounting spindler.

♦ Tighten the clamping nute in a clockwise di-

rection using the two-hole assembly spannerz.

NOTE

► If the disc does not turn smoothly or vibrates

after the change, the disc must be replaced

immediately.

♦ For safety's sake, run the appliance at maximum

speed for 60 seconds after every disc change.

Be aware of unusual noises and sparks.

♦ Check whether all fastening elements are

correctly ﬁtted.

♦ Make sure that the arrow showing the direction

of rotation (if any) on the cutting or roughing

discs (including diamond cutting discs) and the

direction of rotation of the appliance (arrow

showing the direction of rotation on the head)

are aligned.

Switching on and oﬀ

Check the inserted tool before use. It must be prop-

erly ﬁtted, may not be damaged or damp, should

not have any cracks and must turn freely. Carry

out a 60-second test run. Do not use non-circular

or vibrating tools. Be aware of unusual noises and

sparks. Check afterwards whether all the fastening

elements are correctly ﬁtted.

NOTE

► Always switch on the angle grinder before

making contact with the material, then apply

it to the workpiece.

Switching on

♦ Activate the safety lock-out3 (see ﬁg. D).

♦ Then press the ON/OFF switch2.

Switching oﬀ

♦ Press the ON/OFF switch2 again.

Setting the rotational speed

♦ Set the speed setting wheel1 to a position

between 1 and 6.

PWS 125 F6 GB│IE │ 13 ■

Maintenance and cleaning

WARNING! RISK OF INJURY!

Switch the appliance oﬀ and remove

the power plug before starting any

work on the appliance.

■Do not use any sharp objects to clean the

appliance. Do not allow any liquids to get

into the appliance. The appliance could be

damaged.

■ Replace worn out carbon brushes with the

spare carbon brushes4 via the carbon brush

cover5.

■ Clean the appliance regularly, preferably imme-

diately after completion of the work.

■ Clean the housing with a dry cloth – do not use

petrol, solvents or cleaners which can attack the

plastic.

■ A vacuum cleaner is required for thorough

cleaning of the appliance.

■ Ventilation openings must never be obstructed.

■ Remove any adhering swarf with a brush.

NOTE

► Replacement parts not listed (such as carbon

brushes, switch) can be ordered via our

service hotline.

Disposal

Do not dispose of power tools

in your normal domestic waste!

The adjacent symbol of a crossed-out

dustbin means that this appliance is

subject to Directive 2012/19/EU. This directive

states that this appliance may not be disposed of in

the normal household waste at the end of its useful

life, but must be taken to specially set-up collection

locations, recycling depots or disposal companies.

The disposal is free of charge for the user.

Protect the environment and dispose of this

appliance properly.

Your local community or municipal

authorities can provide information on

how to dispose of the worn-out product.

The packaging is made from environ-

mentally friendly material and can be

disposed of at your local recycling plant.

Dispose of the packaging in an

environmentally friendly manner.

Note the labelling on the packaging

and separate the packaging material

components for disposal if necessary. The packag-

ing material is labelled with abbreviations (a) and

numbers (b) with the following meanings:

1–7: plastics, 20–22: paper and cardboard,

80–98: composites.

The product and its packaging are recyclable.

They are subject to an extended manufacturer

responsibility and will be collected separately.

PWS 125 F6

■ 14 │ GB│IE

Kompernass Handels GmbH

warranty

Dear Customer,

This appliance has a 3-year warranty valid from

the date of purchase. If this product has any faults,

you, the buyer, have certain statutory rights. Your

statutory rights are not restricted in any way by the

warranty described below.

Warranty conditions

The warranty period starts on the date of purchase.

Please keep your receipt in a safe place. This will

be required as proof of purchase.

If any material or manufacturing fault occurs within

three years of the date of purchase of the product,

we will either repair or replace the product for you

or refund the purchase price (at our discretion).

This warranty service requires that you present the

defective appliance and the proof of purchase

(receipt) within the three-year warranty period,

along with a brief written description of the fault

and of when it occurred.

If the defect is covered by the warranty, your

product will either be repaired or replaced by us.

The repair or replacement of a product does not

signify the beginning of a new warranty period.

Warranty period and statutory claims for

defects

The warranty period is not prolonged by repairs

eﬀected under the warranty. This also applies to

replaced and repaired components. Any damage

and defects present at the time of purchase must

be reported immediately after unpacking. Repairs

carried out after expiry of the warranty period shall

be subject to a fee.

Scope of the warranty

This appliance has been manufactured in accord-

ance with strict quality guidelines and inspected

meticulously prior to delivery.

The warranty covers material faults or production

faults. The warranty does not extend to product

parts subject to normal wear and tear or to fragile

parts which could be considered as consumable

parts such as switches or parts made of glass.

The warranty does not apply if the product has

been damaged, improperly used or improperly

maintained. The directions in the operating

instructions for the product regarding proper use

of the product are to be strictly followed. Uses

and actions that are discouraged in the operating

instructions or which are warned against must be

avoided.

This product is intended solely for private use and

not for commercial purposes. The warranty shall

be deemed void in cases of misuse or improper

handling, use of force and modiﬁcations / repairs

which have not been carried out by one of our

authorised Service centres.

The warranty period does not apply to

■ Normal reduction of the battery capacity

over time

■ Commercial use of the product

■ Damage to or alteration of the product by the

customer

■ Non-compliance with safety and maintenance

instructions, operating errors

■ Damage caused by natural hazards

PWS 125 F6 GB│IE │ 15 ■

Warranty claim procedure

To ensure quick processing of your case, please

observe the following instructions:

■ Please have the till receipt and the item number

(IAN) 392682_2201 available as proof of

purchase.

■ You will ﬁnd the item number on the type plate

on the product, an engraving on the product,

on the front page of the operating instructions

(below left) or on the sticker on the rear or

bottom of the product.

■ If functional or other defects occur, please

contact the service department listed either by

telephone or by e-mail.

■ You can return a defective product to us free

of charge to the service address that will be

provided to you. Ensure that you enclose the

proof of purchase (till receipt) and information

about what the defect is and when it occurred.

You can download these instructions

along with many other manuals,

product videos and installation

software at www.lidl-service.com.

This QR code will take you directly to the Lidl

service page (www.lidl-service.com) where you

can open your operating instructions by entering

the item number (IAN) 392682_2201.

NOTE

► For Parkside tools, please send us only the

defective item without the accessories (e.g.

battery, storage case, assembly tools, etc.).

Service

Service Great Britain

Tel.: 0800 404 7657

E-Mail: [email protected]

Service Ireland

Tel.: 1800 101010

E-Mail: [email protected]

IAN 392682_2201

Importer

Please note that the following address is not the

service address. Please use the service address

provided in the operating instructions.

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

GERMANY

www.kompernass.com

PWS 125 F6

■ 16 │ GB│IE

Translation of the original Conformity Declaration

We, KOMPERNASS HANDELS GMBH, document oﬃcer: Mr Semi Uguzlu, BURGSTR. 21,

44867 BOCHUM, GERMANY, hereby declare that this product complies with the following

standards, normative documents and EC directives:

Machinery Directive

(2006/42/EC)

Electromagnetic Compatibility

(2014/30/EU)

RoHS Directive

(2011/65/EU)*

* The manufacturer bears the full responsibility for compliance with this conformity declaration. The object of the

declaration described above complies with the requirements of the Directive 2011/65/EU of the European Parliament

and Council of 8 June 2011 on the limitations of use of certain dangerous substances in electrical and electronic

appliances.

Applied harmonised standards

EN 60745-1:2009/A11:2010

EN 60745-2-3:2011/A13:2015

EN 55014-1:2017/A11:2020

EN 55014-2:2015

EN IEC 61000-3-2:2019

EN 61000-3-3:2013/A1:2019

EN 61000-3-2:2014

EN 61000-3-3:2013

EN IEC 63000:2018

Type designation of machine: Angle grinder PWS 125 F6

Year of manufacture: 05–2022

Serial number: IAN 392682_2201

Bochum, 13/04/2022

Semi Uguzlu

- Quality Manager -

We reserve the right to make technical changes in the context of further product development.

Stránka sa načítava...

Parkside PWS 125 F6 Používateľská príručka

Súvisiace články

Ostatné dokumenty