Parkside 95929 Translation Of Original Operation Manual

Kategória
Elektrické náradie
Typ
Translation Of Original Operation Manual

Táto príručka je tiež vhodná pre

IAN 95929
ANGLE GRINDER PWS 230 A1
WINKELSCHLEIFER
Bedienungs- und Sicherheitshinweise
Originalbetriebsanleitung
ANGLE GRINDER
Operation and Safety Notes
Translation of original operation manual
SAR OK CSISZOLÓ
Kezelési és biztonsági utalások
Az originál használati utasítás fordítása
KOTNI BRUSILNIK
Navodila za upravljanje in varnostna opozorila
Prevod originalnega navodila za uporabo
ÚHLOVÁ BRUSKA
Pokyny pro obsluhu a bezpečnostní pokyny
eklad originálního provozního návodu
UHLOVÁ BRÚSKA
Pokyny pre obsluhu a bezpečnostné pokyny
Preklad originálneho návodu na obsluhu
GB Operation and Safety Notes Page 5
HU Kezelési és biztonsági utalások Oldal 19
SI Navodila za upravljanje in varnostna opozorila Stran 35
CZ Pokyny pro obsluhu a bezpečnostní pokyny Strana 49
SK Pokyny pre obsluhu a bezpečnostné pokyny Strana 63
DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 77
Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the
device.
Olvasás előtt kattintson az ábrákat tartalmazó mindkét oldalra és végezetül ismerje meg a készülék minde-
gyik funkcióját.
Pred branjem obe strani s slikami odprite navzven in se nato seznanite z vsemi funkcijami naprave.
Před čtením si odklopte obě dvě strany s obrázky a potom se seznamte se všemi funkcemi přístroje.
Pred čítaním si odklopte obidve strany s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.
Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich anschließend
mit allen Funktionen des Gerätes vertraut.
A B
4
2
6
3
11
12
5
7
1
4
8 9 10
E
C
19
F
14
15
16
13
0
1
G
3
17
D
18
12
5 GB
Table of contents
Introduction
Proper use ............................................................................................................................................Page 6
Features and equipment .....................................................................................................................Page 6
Included items .....................................................................................................................................Page 6
Technical information .......................................................................................................................... Page 6
General power tool safety warnings
1. Work area safety............................................................................................................................Page 7
2. Electrical safety ............................................................................................................................... Page 7
3. Personal safety ................................................................................................................................Page 7
4. Power tool use and care ................................................................................................................Page 8
5. Service .............................................................................................................................................Page 8
Safety advice for all uses ....................................................................................................................Page 8
Safety advice relating to kickback .....................................................................................................Page 10
Special safety advice relating to grinding and disc-cutting ..............................................................Page 10
Further special safety advice for disc-cutting ..................................................................................... Page 11
Special safety advice for abrading using sandpaper ......................................................................Page 11
Special safety advice for polishing ....................................................................................................Page 11
Special safety advice for working with wire brushes ........................................................................Page 11
Safety advice for angle grinders ........................................................................................................Page 12
Advice on use ......................................................................................................................................Page 13
Preparing for use
Attaching the disc guard cover using the quick-release fastener .....................................................Page 14
Attaching the auxiliary handle ...........................................................................................................Page 14
Attaching and replacing roughing / grinding / cutting discs ............................................................Page 14
Operation
Switching on and off ........................................................................................................................... Page 15
Maintenance and cleaning ............................................................................................... Page 15
Service ...............................................................................................................................................Page 16
Warranty .........................................................................................................................................Page 16
Disposal ............................................................................................................................................Page 16
Declaration of Conformity / Manufacturer..........................................................Page 17
6 GB
Introduction / General power tool safety warnings
Introduction
Angle grinder PWS 230 A1
Q
Introduction
We congratulate you on the purchase of
your new
device. You have chosen a
high quality product. The
instructions for use are part of the product. They
contain important information concerning safety,
use and disposal. Before using the product, please
familiarise yourself with all of the safety information
and instructions for use. Only use the unit as descri-
bed and for the specified applications. If you pass
the product on to anyone else, please ensure that
you also pass on all the documentation with it.
Q
Proper use
This tool is suitable for cutting, roughing and brush-
ing metal materials without the use of water. Any
other use or modification to the device shall be
considered as improper use and could give rise to
considerable dangers. We will not accept liability
for loss or damage arising from improper use. The
device is not intended for commercial use.
Note: Slots cut in load-bearing walls must comply
with standard DIN 1053 Part 1 or the regulations
applicable in your country.
These instructions and advice must be observed.
Before you start a task, seek the advice of a com-
petent structural engineer, architect, or the relevant
site management staff.
Q
Features and equipment
1
Hand grip (rotatable)
2
ON / OFF switch
3
Safety lock-out
4
Unlocking button
5
Carbon brushes cover
6
Auxiliary handle
7
Disc guard cover
8
Clamping lever
9
Coded projection
10
Adjuster screw
11
Spindle lock button
12
Threaded hole (3 x) for auxiliary handle
13
Clamping nut (see Fig. F)
14
Mounting spindle (see Fig. F)
15
Mounting flange (see Fig. F)
16
Coded groove (see Fig. F)
17
Spanner
18
Roughing / grinding disk*
19
Cutting disc for metal* (see Fig. E)
* not included
Q
Included items
1 Angle grinder PWS 230 A1
1 Auxiliary handle
1 Disc guard cover
1 Spanner
1 Operating instructions
Q
Technical information
Rated voltage: 230–240 V
~
50 Hz
Rated power consumption: 2000 W
Rated speed: n 6500 min
-1
Grinding disc: Ø 230 mm
Mounting spindle: M14 / threaded
Protection class: II /
Noise and vibration data:
Measured values for noise are determined in accor-
dance with EN 60745. The A-weighted noise level
of the electrical power tool are typically:
Sound pressure level: 96.8 dB(A)
Sound power level: 107.8 dB(A)
Uncertainty K: 3 dB
Wear ear protection!
Evaluated acceleration, typical:
Hand / arm vibration a
h
= 10.075 m / s
2
Uncertainty K = 1.5 m / s
2
The vibration level specified in
these instructions was measured in accordance with
an EN 60745 standardised measurement process
7 GB
Introduction / General power tool safety warnings
Introduction
and can be used to compare equipment. The vibra-
tion emission value specified can also serve as a
preliminary assessment of the exposure.
The vibration level will change according to the ap-
plication of the electrical tool an in some cases may
exceed the value specified in these instructions.
Regularly using the electric tool in such a way may
make it easy to underestimate the vibration.
Note: If you wish to make an accurate assessment
of the vibration loads experienced during a particular
period of working, you should also take into account
the intervening periods of time when the device is
switched off or is running but is not actually in use.
This can result in a much lower vibration load over
the whole of the period of working.
General power tool
safety warnings
Read all safety warnings
and all instructions. Failure to follow the warn-
ings and instructions may result in electric shock, fire
and / or serious injury.
Save all warnings and instructions for
future reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-op-
erated (cordless) power tool.
1. Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) D
o not operate power tools in explosive
atmospheres, such as in the presence
of flammable liquids, gases or dust.
Power tools create sparks which may ignite the
dust or fumes.
c) Keep children and bystanders away
while operating a power tool. Distractio
ns
can cause you to lose control.
2. Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plug
s
and matching outlets will reduce risk of electric
shock.
b) Avoid body contact with earthed or
grounded surfaces, such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of electric shock if
your body is earthed or grounded.
c) Do not expose power tools to rain or
wet conditions. Water entering a power tool
will increase the risk of electric shock.
d) Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk
of electric shock.
e)
When operating a power tool outdo
ors,
use an extension cord suitable for out-
door use. Use of a cord suitable for outdoor
use reduces the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
3. Personal safety
a) Stay alert, watch what you are doing
and use common sense when operat-
ing a power tool. Do not use a power
tool while you are tired or under the
influence of drugs, alcohol or medica-
tion. A moment of inattention while operating
power tools may result in serious personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal in-
juries.
8 GB
c) Prevent unintentional starting. Ensure
the switch is in the off-position before
connecting to power source and / or
battery pack, picking up or carrying
the tool. Carrying power tools with your fing
er
o
n the switch or energising power tools that hav
e
the switch on invites accidents.
d) Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating part
of the power tool may result in personal injury.
e) Do not overreach. Keep proper foot-
ing and balance at all times. This enables
better control of the power tool in unexpected
situations.
f) Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from mov-
ing parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
g) If devices are provided for the connec-
tion of dust extraction and collection
facilities, ensure these are connected
and properly used. Use of dust collection
can reduce dust-related hazards.
4. Power tool use and care
a) Do not force the power tool. Use the
correct power tool for your applica
tion.
The correct power tool will do the job better
and safer at the rate for which it was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from the power
source and / or the battery pack from
the power tool before making any ad-
justments, changing accessories, or
storing power tools. Such preventive safety
measures reduce the risk of starting the power
tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of un-
trained users.
e) Maintain power tools. Check for mis-
alignment or binding of moving parts,
breakage of parts and any other con-
dition that may affect the power tool’s
operation. If damaged, have the power
tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and
tool bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended could
result in a hazardous situation.
5. Service
a) Have your power tool serviced by a
qualified repair person using only
iden-
tical replacement parts. This will ensure
that the safety of the power tool is maintained.
Q
Safety advice for all uses
General safety advice for grinding,
sanding (with sandpaper), wire brushing,
polishing and disc-cutting:
a) This electrical power tool is intended
for use as a grinding, sanding, wire-
brushing, and disc-cutting machine.
Observe all the safety advice, instruc-
tions, information in figures and all
other information you received with
this device. If you do not observe the follow-
ing advice it could lead to electric shock, fire
and / or serious injury.
b) Normative statement / advice for this tool is not
applicable.
General power tool safety warnings
General power tool safety warnings
9 GB
c) Do not use any accessory not specifi-
cally intended by the manufacturer
for this electrical power tool. Although
an accessory may fit on your electrical power
tool, this does not on its own guarantee that it
can be safely used.
d) The maximum permitted speed of an
attachment must be at least as high as
the maximum speed indicated for the
electrical power tool. An accessory rotating
faster than its permitted speed could disintegrate
or fly off.
e) The external diameter and the thickness
of the attachment must be compatible
with the dimensions of your electrical
power tool. Attachments that are not dimen-
sionally compatible cannot be adequately
guarded or controlled.
f) Grinding discs, flanges, grinding
wheels or other accessories must fit
exactly on to the spindle of your elec-
trical power tool. Attachments that do not
exactly fit on the spindle turn unevenly, vibrate
severely and could lead to loss of control.
g) Do not use damaged attachments.
Before every use check attachments
such as grinding discs for loose frag-
ments and cracks, grinding wheels for
cracks, deterioration or excessive
wear and wire brushes for loose or
broken wires. If the electrical power
tool or attachment is dropped, inspect
for damage or change the attachment
for an undamaged one. When you
have inspected and inserted the at-
tachment, position yourself and by-
standers away from the plane of the
rotating attachment and run the device
at maximum speed for one minute.
Damaged attachments will usually break apart
during this test.
h) Wear personal protective equipment.
Use a full face visor, safety goggles or
safety glasses, depending on the ap-
plication. Wear a dust mask, hearing
protectors, safety gloves or special
apron capable of stopping particles of
the grinding medium or workpiece,
as appropriate for the task. Eyes must
be protected from the flying debris which can
arise from some operations. Dust or breathing
masks must be capable of filtering out the dust
generated by the application. Prolonged expo-
sure to loud noise can lead to hearing loss.
i) Keep bystanders at a safe distance
from your work area. Anyone entering
the work area must wear personal
protective equipment. Fragments of the
workpiece or of a broken attachment could fly
off and cause injury beyond the immediate
working area.
j) Hold the device by the insulated han-
dle surfaces when you are undertak-
ing work where there is the danger
of the attachment striking hidden
electricity cables or the device’s mains
lead. Contact with a live wire could cause
metal parts of the device to become live and
lead to electric shock.
k) Keep the mains lead away from rotat-
ing attachments. If you lose control of the
device the mains lead may become severed or
trapped and your hand or arm may be pulled
into the rotating attachment.
l) Never lay the electrical power tool
down until after the attachment has
come to a complete standstill. The rotat-
ing attachment may snag when it comes into
contact with the surface and cause you to lose
control of the device.
m) Do not have the electrical power tool
running while you are carrying it. Your
clothing could become trapped by unintention-
al contact with the rotating attachment and the
tool could be pulled into your body.
n) Clean the ventilation slots on your
electrical power tool regularly. The mo-
tor’s fan draws dust into the housing. A build-up
of metal dust could give rise to an electrical
hazard.
o) Never use the electrical power tool
near inflammable materials. Sparks
could ignite these materials.
General power tool safety warnings
General power tool safety warnings
10 GB
p) Do not use attachments that require
the use of coolants. The use of water or
other liquid coolants could result in electric shock.
Q
Safety advice
relating to kickback
Kickback is the sudden reaction to a pinched or
snagged rotating attachment, such as a grinding
disc, grinding pad, wire brush etc. Pinching or
snagging results in the rotating attachment coming
to an abrupt stop. This causes the electrical power
tool (if not controlled) to move in the opposite di-
rection to the direction of rotation of the attachment
at the point of constraint.
If, for example, a grinding disc is pinched or snags
in a workpiece, this can cause the edge of the
grinding disc to penetrate the workpiece, become
trapped there and either free itself or kickback. The
grinding disc moves towards or away from the op-
erator, depending on the direction of movement of
the disc at the point of constraint. The grinding disc
could also break.
Kickback occurs as a result of incorrect use or mis-
use of the electrical power tool. It can be prevented
by taking the appropriate precautions as described
below.
a) Maintain a firm grip on the electrical
power tool and position your body
and arms to allow you to resist kick-
back forces. Always use the auxiliary
handle, if provided, to exercise the
greatest possible control over kick-
back forces or reaction torques as the
device builds up to full speed. By taking
suitable precautions the operator can control
kickback and reaction forces.
b) Do not place your hands near a rotat-
ing attachment. If kickback occurs the at-
tachment could move over your hand.
c) Avoid positioning your body in the
area into which the electrical power
tool would move in the event of a
kickback. A kickback moves the electrical
power tool in the opposite direction to the di-
rection of movement of the grinding disc at the
point of constraint.
d) Work particularly carefully in the
area of corners, sharp edges etc. to
avoid the attachment bouncing or
snagging on the workpiece. Corners,
sharp edges or bouncing have a tendency to
snag the rotating attachment. This causes loss
of control or kickback.
e) Do not use saw-chain woodcarving
discs or toothed discs. Such attachments
create frequent kickback and loss of control of
the electrical power tool.
Q
Special safety advice relating
to grinding and disc-cutting
a) Always use the guard designed for the
type of abrasive consumable you are
using. Always use abrasive consuma-
bles approved for use with your elec-
trical power tool. Abrasive consumables not
approved for use with your electrical power tool
cannot be adequately guarded and are unsafe.
b) To ensure the highest level of opera-
tional safety, the disc guard cover must
be attached to the electrical power tool
and set in such a way that the smallest
possible area of the abrasive consum-
able is exposed to the operator. The disc
guard cover is there to protect the operator
from pieces breaking off and accidental con-
tact with the abrasive consumable.
c) Abrasive consumables must be used
only for their recommended purposes,
For example: never grind with the side
face of a cutting disc. Cutting discs are in-
tended for removing material using the edge
of the disc. Sideways forces on these abrasive
consumables can cause them to break.
d) Always use an undamaged mounting
flange of the correct size and shape
for your selected grinding disc. Suitable
flanges support the grinding disc and reduce
General power tool safety warnings
General power tool safety warnings
11 GB
the chance of it breaking. Flanges for cutting
discs are different from the flanges for other
abrasive discs.
e) Never use worn down abrasive con-
sumables intended for larger electrical
power tools. Abrasive consumables intended
for larger electrical power tools are not designed
for the faster rotational speeds of these smaller
electrical power tools and could break.
Q
Further special safety
advice for disc-cutting
a) Avoid snagging the cutting disc and
do not use too much contact pressure.
Do not attempt to make excessively
deep cuts. Overloading the cutting disc in-
creases the load and the tendency of the disc
to twist or snag in the cut, making kickback or
disc breakage more likely.
b) Avoid the area in front of or behind
the rotating cutting disc. If the cutting disc
is moving away from you at the point of con-
straint in the workpiece, then, in the event of
a kickback, the electrical power tool and the
rotating disc may be thrown towards you.
c) If the cutting disc jams or you stop
work for a while, switch the device
off and hold it until the disc comes to
a complete stop. Never attempt to
pull the still rotating cutting disc out of
the cut as this could cause kickback.
Determine and rectify the reason for the jamming.
d) Do not switch on the device if the cut-
ting disc is in the workpiece. Allow
the cutting disc to reach full speed be-
fore carefully continuing with the cut.
Otherwise the disc could snag, jump out of the
workpiece or cause a kickback.
e) Support boards or workpieces whilst
cutting to reduce the risk of kickback
caused by a jammed cutting disc. Large
workpieces may bend under their own weight.
The workpiece must be supported to both sides
of the cutting disc and particularly near the
cutting disc and at the workpiece edge.
f) B
e particularly careful when pocket
cutting in existing walls or other areas
where you cannot see what you are cut
-
t
ing into. The cutting disc plunged into the surface
could cut through gas or water pipes, electricity
cables or other objects and cause kickback.
Q
Special safety advice for
abrading using sandpaper
Do not use over-sized sanding sheets.
Follow the manufacturer’s recommen-
dations for sanding sheet size. Sanding
sheets that project beyond the backing pad
could cause injury in addition to jamming,
tearing of the sheet or kickback.
Q
Special safety
advice for polishing
Do not use the polishing bonnet if it
has any loose parts, in particular the
fastening cords. Tuck the fastening cords
away or trim them. Loose fastening cords rotat-
ing with the attachment could catch your fingers
or become trapped in the workpiece.
Q
Special safety advice for
working with wire brushes
a) Bear in mind that wire brushes lose
pieces of wire during normal use. Do
not overload the wires by applying too
much pressure. Flying pieces of wire can very
easily penetrate thin clothing and / or skin.
b) Use a guard, if recommended, but
make sure that the wire brush does
not come into contact with the guard.
The diameters of disc brushes and cup brushes
can increase due to contact pressure and cen-
tripetal forces.
General power tool safety warnings
General power tool safety warnings
12 GB
Q
Safety advice for angle grinders
DANGER OF ELECTRIC SHOCK! Do not
operate the device if the mains lead
or mains plug is damaged.
DANGER OF ELECTRIC SHOCK! Do not
touch the mains lead if it becomes
damaged or cut through while you
are using the device. Pull the plug out of
the mains socket immediately and have the de-
vice repaired by a suitably qualified person or
at your service centre.
DANGER OF ELECTRIC SHOCK! Do not
operate the device if it is damp and
do not use it in a damp environment.
DANGER OF ELECTRIC SHOCK! If you
use the device outdoors, always con
nect
it through a residual current device
(RCD) with a maximum trip current of
30 mA. If using an extension lead, always use
one that is approved for outdoor use.
Do not suspend or carry the device by
the mains lead. Always work with the
mains lead leading away from the
rear of the device. Otherwise the device
could be damaged.
Grinding discs must be carefully kept
and handled in accordance with the
manufacturer’s instructions. Otherwise
they could be damaged.
Make sure that abrasive consumables
and tools are attached in accordance
with the manufacturer’s instructions
and advice. Otherwise they could become
detached from the device and result in injury
and / or damage to property.
Ensure that any spacers supplied and
required for the use of certain abrasive
consumables and tools are installed.
Do not use separate reducing bushes
or adapters in order to make grinding
discs with a larger bore fit.
When using abrasive consumables
and tools with a threaded insert make
sure that the tread is long enough for
the spindle length. Otherwise the grinding
discs could become detached from the device
and result in injury and / or damage to property.
Do not allow the end of the spindle
to contact the base of the hole in the
abrasive consumable.
Do not work in areas where there may
be concealed electricity cables or gas
or water pipes. Use a suitable detector
or ask your local utility service pro-
viders. Contact with electricity cables can
lead to fire or electric shock. Damaging a gas
pipe can lead to an explosion. Penetration of a
water pipe can lead to property damage or to
electric shock.
NOXIOUS FUMES!
Working with harmful / noxious dusts represents
a risk to the health of the person operating the
device and to anyone near the work area.
For longer periods of cutting or grind-
ing metal or stone materials which
give rise to dusts that are hazardous
to health, the device must be connected
to a suitable external dust extraction
device.
Ensure that there is adequate ventila-
tion when working on plastic, paint,
varnish etc.
Do not soak the materials or the sur-
face you are about to work on with
liquids containing solvents.
DANGER OF INJURY! Wear close-fitting
clothing and keep long hair inside a
hairnet or suitable headwear.
For safety reasons this device must
always be used with the auxiliary
handle
6
in place.
The adjustable disc guard cover
7
must
always be in place when working with
roughing, grinding or cutting discs.
Otherwise there could be danger of injury.
Use the vacuum dust extraction facility
if your work generates high amounts
of dust. Use suction devices particular-
ly approved for the purpose.
Use permitted consumables and tools
only. Check that the speed given on the
discs is greater or equal to the rated
speed of the device.
Take note of the direction of rotation
and always hold the device in such a
General power tool safety warnings
General power tool safety warnings
13 GB
way that the sparks and grinding de-
bris are thrown away from your body.
Otherwise there could be danger of injury.
Make sure that the dimensions of the
disc are suitable for the device and
that the disc is of a type that fits prop-
erly on to the mounting flange
15
.
Q
Advice on use
Note! Discs must be used only for their recom-
mended purposes, otherwise they could disintegrate,
become damaged or cause accidents.
Roughing:
Never use cutting discs for
roughing or grinding!
Move the angle grinder using even
pressure to and fro over the workpiece.
Hold the roughing or grinding disc at
a flat angle to the workpiece when
working on a soft material. Use a
slightly steeper angle for harder ma-
terials.
Disc-cutting:
Never use roughing or
grinding discs for cutting!
Only use certified fibre-reinforced cut-
ting or grinding discs approved for use at
circumferential speeds of not less than 80 m / s.
CAUTION! The disc continues to rotate after
the device has been switched off. Do not at-
tempt to slow it down by pressing on the side
of the disc.
Securely support the workpiece. Use
clamps or a vice to grip the workpiece firmly.
This is much safer than holding it in your hand.
Switch the device off and allow it to
come to a complete standstill before
you put it down.
Unlock the ON / OFF switch immedi-
ately if a power failure occurs or the
plug is pulled out of the mains socket.
Place the switch in the OFF position.
This prevents the device from being inadvertent-
ly started up again.
Use the device for dry cutting or dry
grinding only.
The auxiliary handle
6
must be in
place
whenever the device is being used.
Do not work on materials containing
asbestos. Asbestos is a known carcinogen.
A tip! Using the device safely.
DANGER! Always guide
the device through the
workpiece against the di-
rection of rotation of the
disc. If you work in the other direction there is
the risk of kickback. The device may be forced
out of the cut.
Always switch on the device before
placing it against the workpiece. After
cutting or grinding, always lift the device from
the workpiece before switching it off.
When working always hold the device
securely with both hands (see Fig. D).
Always keep proper footing and balance.
For the best grinding performance move the
device evenly to and fro over the workpiece
maintaining an angle of 15° to 30° (between
grinding disc and workpiece).
When working on inclined surfaces do
not press the device hard down on to
the workpiece. If the speed slows greatly,
use less pressure. This will allow you to work
more effectively and safely. If the device sudden-
ly stops due to it becoming retarded or trapped,
pull the mains plug from the socket immediately.
Cutting: Advance the device at an
appropriate rate. Do not incline the
cutting disc.
Roughing, grinding and cutting discs
get hot during use – allow them to
cool fully before touching them.
Never use the device for a purpose
for which it was not intended.
Before you insert the mains plug into
the socket, always check that the de-
vice is switched off.
General power tool safety warnings
General power tool safety warnings
14 GB
If a dangerous situation arises, pull
the mains plug immediately out of the
mains socket. Ensure that the device and
the mains plug are easily accessible and can
be reached quickly in an emergency.
When taking a break from your
work, before carrying out any tasks
on the device itself and when you are
not using the device, always pull the
mains plug out of the mains socket.
Always keep the device clean, dry and free of
oil or grease.
Remain alert at all times! Always watch
what you are doing and proceed with
caution. Do not use the device if you cannot
concentrate or you are feeling unwell.
Q
Preparing for use
Q
Attaching the disc guard cover
using the quick-release fastener
DANGER OF INJURY!
Pull the mains plug out of the mains
socket before you carry out any task
on the device.
DANGER OF INJURY! Always use the
angle grinder with the disc guard
cover in place. The disc guard cover must
be securely attached to the angle grinder. To
ensure the highest level of safety while using
the device, ensure that the smallest possible
area of the grinding or cutting tool is exposed
to the operator at all times. The disc guard cov-
er is there to protect the operator from pieces
breaking off and accidental contact with the
grinding or cutting tool.
DANGER OF INJURY! Ensure that the
guard
7
is attached so that its edge
is beyond the angle of the auxiliary
handle
6
(see Fig. B). Otherwise you
could injure yourself against the grinding or
cutting disc.
Open the clamping lever
8
.
Insert the disc cover guide
7
with the coded
projection
9
in the coded groove
16
.
Turn the disc guard cover
7
into the desired
position (working position). The closed side of
the disc guard cover
7
must always be facing
the operator.
Close the clamping lever
8
to firmly clamp
the disc guard cover
7
in place.
If necessary the clamping force of the connection
can be adjusted by tightening or loosening the
adjuster screw
10
.
Ensure that the disc guard cover
7
sits firmly
on the spindle collar.
Q
Attaching the auxiliary handle
CAUTION! For safety reasons this
device must always be used with the
auxiliary handle
6
in place. Otherwise
you could become injured.
DANGER OF INJURY!
Pull the mains plug out of the mains
socket before you carry out any task
on the device.
Screw the auxiliary handle
6
on the left, right
or on the top of the head of the device.
Q
Attaching and replacing
roughing / grinding / cutting discs
Take note of the dimensions of the roughing /
grinding or cutting discs. The circular hole must fit
on to the mounting flange without play. Do not use
a reducer piece or adapter.
DANGER OF INJURY!
Pull the mains plug out of the mains
socket before you carry out any task
on the device.
Check the condition of the roughing /
grinding or cutting discs. They must be
free of damage, moisture or cracks.
Otherwise they could break up during use and
cause injury.
DANGER OF BURNS! Always wear
protective gloves when changing a
roughing / grinding or cutting disc.
Roughing / grinding and cutting discs become
Preparing for use / Operation / Maintenance and cleaning
General power tool safety warnings / Preparing for use
15 GB
hot during use. Do not touch them until after
they have cooled down.
NOTE: Always ensure the discs are free of dirt
before use.
Use only abrasive consumables or tools with
an allowable speed at least as high as the
no-load speed of the device.
DANGER OF INJURY! Press the spindle lock
button
11
only after the mounting spindle
14
has reached a standstill.
Press the spindle lock button
11
to block the drive.
Release the clamping nut
13
using the spanner
17
(see Fig. C).
Place the roughing / grinding or cutting disc on
to the mounting flange
15
with its labelled side
facing towards the device.
Then replace the clamping nut
13
, with its
raised side facing upwards, on to the mounting
spindle
14
.
Press the spindle lock button
11
to block the drive.
Tighten the clamping nut
13
again with the
spanner
17
.
NOTE: Replace a new disc immediately if it
runs unevenly or vibrates after being exchanged.
After replacing a disc let the device run under
no-load conditions for 30 seconds as a safety
check. Look out for unusual noises or generation
of sparks. Check that all the fastened-on parts
are correctly attached.
Pay attention to see that the arrow showing the
direction of rotation on the roughing / grinding
or cutting discs (including diamond cutting discs)
corresponds with the direction of rotation of the
device (see arrow on the head of the device).
Q
Operation
Q
Switching on and off
Note: Always switch on the angle grinder before
bringing it into contact with the workpiece material.
Switching on the device:
Press the safety lock-out
3
(see Fig. G).
Then press the ON / OFF switch
2
.
Switching off the device:
Release the ON / OFF switch
2
.
Rotating the hand grip:
DANGER OF INJURY!
Pull the mains plug out of the mains
socket before you carry out any task
on the device.
The hand grip
1
can be rotated by 90° to
the right or left (see Fig. A).
This allows the ON / OFF switch
2
to be
brought into the most comfortable position for
any working conditions.
Press the unlocking button
4
and rotate the
hand grip
1
to the right or left.
Make sure the hand grip
1
engages.
Q
Maintenance and cleaning
DANGER OF INJURY!
Pull the mains plug out of the mains
socket before you carry out any task
on the device.
Do not use sharp objects for cleaning
the device. Do not allow any liquids
to enter the device. Otherwise the device
could be damaged.
Have the carbon brushes replaced only at the
service centre or an accredited electrical
equipment repair centre. The device requires
no other maintenance.
Clean the device frequently; for best results do
this immediately after you have finished using it.
Use a dry cloth to clean the housing – under
no circumstances use petrol, solvents or cleaning
agents that attack plastic.
A vacuum cleaner is required to thoroughly
clean the device.
Ventilation openings must always be kept free.
Remove any adhering dust with a narrow paint
brush.
Preparing for use / Operation / Maintenance and cleaning
General power tool safety warnings / Preparing for use
16 GB
Q
Service
Have your device
repaired at the service centre or by
qualified specialist personnel using
original manufacturer parts only. This
will ensure that your device remains safe to use.
If the plug or lead needs
to be replaced, always have the
replacement carried out by the manu-
facturer or its service centre. This will
ensure that your device remains safe to use.
Q
Warranty
The warranty for this appliance is for 3 year
s
from the date of purchase. The appliance
has been manufactured with care and me-
ticulously examined before delivery. Please
retain your receipt as proof of purchase. In
the event of a warranty claim, please make
contact by telephone with our Service
Department. Only in this way can a post-
free despatch for your goods be assured.
The warranty covers only claims for material and
maufacturing defects, but not for transport damage,
for wearing parts or for damage to fragile components,
e.g. buttons or batteries. This product is for private use
only and is not intended for commercial use.
The warranty is void in the case of abusive and
improper handling, use of force and internal tam-
pering not carried out by our authorized service
branch. Your statutory rights are not restricted in
any way by this warranty.
The warranty period will not be extended by repairs
made unter warranty. This applies also to replaced
and repaired parts. Any damage and defects extant
on purchase must be reported immediately after
unpacking the appliance, at the latest, two days after
the purchase date. Repairs made after the expiration
of the warranty period are subject to payment.
GB
Service Great Britain
Tel.: 0871 5000 720
(0,10 GBP/Min.)
IAN 95929
Q
Disposal
The packaging is wholly composed of
environmentally-friendly materials that can
be disposed of at a local recycling centre.
Do not dispose of electric tools
in the household waste!
In accordance with European Directive 2002 / 96 / EC
(covering waste electrical and electronic equipment)
and its transposition into national legislation, worn out
electrical power tools must be collected separately
and taken for environmentally compatible recycling.
Contact your local refuse disposal authority for more
details of how to dispose of your worn out electrical
devices.
Declaration of Conformity / Manufacturer
Service / Warranty / Disposal
17 GB
Q
Declaration of Conformity /
Manufacturer
We, KOMPERNASS HANDELS GMBH, the person
responsible for documents: Mr Semi Uguzlu, BURG-
STRASSE 21, 44867 BOCHUM, GERMANY, hereby
declare that this product complies with the following
standards, normative documents and EU directives:
Machinery Directive
(2006 / 42 / EC)
EU Low Voltage Directive
(2006 / 95 / EC)
Electromagnetic Compatibility
(2004 / 108 / EC)
RoHS Directive
(2011 / 65 / EU)
Applicable harmonized standards
EN 60745-1/A11:2010
EN 60745-2-3:2011
EN 55014-1/A1:2009
EN 55014-2/A2:2008
EN 61000-3-2/A2:2009
EN 61000-3-3:2008
Type / Device description:
Angle grinder PWS 230 A1
Date of manufacture (DOM): 12–2013
Serial number: IAN 95929
Bochum, 31.12.2013
Semi Uguzlu
- Quality Manager -
We reserve the right to make technical modifica-
tions in the course of further development.
Declaration of Conformity / Manufacturer
Service / Warranty / Disposal
18
Tartalomjegyzék
19 HU
Tartalomjegyzék
Bevezetés
Rendeltetésszerű használat ...............................................................................................................Strona 20
Felszerelés ..........................................................................................................................................Strona 20
A szállítmány tartalma .......................................................................................................................Strona 20
Műszaki adatok .................................................................................................................................Strona 20
Elektromos szerszámokra vonatkozó általános
biztonsági tudnivalók
1. A munkahely biztonsága ..............................................................................................................Strona 21
2. Elektromos biztonsága ..................................................................................................................Strona 21
3. Személyek biztonsága ..................................................................................................................Strona 22
4. Az elektromos szerszámokkal való gondos járás és azok gondos használata ........................Strona 22
5. Szervíz ............................................................................................................................................Strona 23
Biztonsági tudnivalók minden alkalmazáshoz .................................................................................Strona 23
Visszarúgás és az arra vonatkozó biztonsági tudnivalók ...............................................................Strona 24
A csiszolásra és vágásra vonatkozó sajátos biztonsági tudnivalók ...............................................Strona 25
A vágótárcsákkal való munkákra vonatkozó további biztonsági tudnivalók ................................Strona 25
Csiszolópapírral való munkákra vonatkozó sajátos biztonsági tudnivalók ...................................Strona 26
A polírozásra vonatkozó sajátos biztonsági tudnivalók .................................................................Strona 26
A drótkefével való munkákra vonatkozó sajátos biztonsági tudnivalók ........................................Strona 26
Sarokcsiszolókra vonatkozó biztonsági tudnivalók .........................................................................Strona 26
A munkára vonatkozó utalások ........................................................................................................Strona 27
Üzembevétel
A védőburkolatnak a gyorszárral való felszerelése ........................................................................Strona 28
A pótfogantyú felszerelése ................................................................................................................Strona 29
Nagyoló- / vágótárcsa felszerelése / cseréje ...................................................................................Strona 29
Kezelés
Be- és kikapcsolás ..............................................................................................................................Strona 30
Karbantartás és tisztítás ...................................................................................................Strona 30
Szervíz ..............................................................................................................................................Strona 30
Garancia .........................................................................................................................................Strona 30
Mentesítés .....................................................................................................................................Strona 31
Konformitásnyilatkozat / Gyártó ..............................................................................Strona 31
Jótállási tájékoztató .............................................................................................................Strona 32
20 HU
Bevezetés / Elektromos szerszámokra vonatkozó általános biztonsági tudnivalók
Bevezetés
Sarokcsiszoló PWS 230 A1
Q
Bevezetés
Gratulálunk új készülékének vásárlása alkalmából.
Ezzel a döntésével vállalatunk értékes terméke mel-
lett döntött.
A használati utasítás ezen termék része. A
biztonságra, a használatára és a megsemmisítésre
vonatko fontos tudnivalókat tartalmazza. A termék
használata előtt ismerje meg az összes használati és
biztonsági tudnivalót. A terméket csak a leírtak sze-
rint és a megadott felhasználási területeken alkal-
mazza. A termék harmadik személy számára való
továbbadása esetén kézbesítse vele annak a teljes do-
kumentációját is.
Q
Rendeltetésszerű használat
A készülék fémek darabolására, nagyolására és
kefézésére alkalmas víz használata nélkül. Minden
másfajta alkalmazás, vagy ap megváltoztasa
nem rendeltetésszerűnek számit és jelentős baleset-
veszélyeket rejt magában. A rendeltetésétől eltérő
alkalmazásból származó károkért nem állunk jót. A
készülék nem ipari alkalmazásra készült.
Utalás: A tartó falakban levő réseknek meg kell
felelni a DIN 1053 1. részének és az országspe-
cifikus szabályozásoknak.
Ezeket az előírásokat feltétlenül be kell tartani. A
munka
megkezdése előtt kérjen tanácsot a felelős statikustól,
épitésztől, vagy az illetékes építésvezetéstől.
Q
Felszerelés
1
Készülékfogantyú (elforgatható)
2
BE- / KI-kapcsoló
3
Bekapcsolási retesz
4
Kireteszelő gomb
5
Szénkefék burkolata
6
Pótfogant
7
Védőburkolat
8
Feszítőkar
9
Vezető orr
10
Beállító csavar
11
Tengelyrögzítő gomb
12
Menetek (3 x) a pótfogantyú számára
13
Szorító anya (lásd a F ábrát)
14
Felfogó tengely (lásd a F ábrát)
15
Felfogó karima (lásd a F ábrát)
16
Vezető horony (lásd a F ábrát)
17
Szorító kulcs
18
Nagyoló tárcsa*
19
Vágótárcsa fémekhez* (lásd a E ábrát)
* nem részei a szállítmánynak
Q
A szállítmány tartalma
1 sarokcsiszoló PWS 230 A1
1 pótfogant
1 védőburkolat
1 szorító kulcs
1 kezelési utasítás
Q
Műszaki adatok
Névleges feszültség: 230–240 V∼ 50 Hz
Névleges teljesítmény: 2000 W
Mérési fordulatszám: n 6500 perc
-1
Csiszoló tárcsa: Ø 230 mm
Felfogó tengely: M14 / menet
Védettségi osztály: II /
Zaj- és rezgésinformációk:
A hangszint mért értékeit az EN 60745 szabvány-
nak megfelelően állapították meg. Az elektromos
szerszám A-kiemelés szerinti hangszintje tipikusan
a következő:
Hangnyomásszint: 96,8 dB(A)
Hangteljesítményszint: 107,8 dB(A)
Bizonytalansági tényező K: 3 dB
Viseljen hallásvédőt!
Értékelt gyorsulás, jellemző:
Kéz-kar-rezgé a
h
= 10,075 m / s
2
Bizonytalansági tényező K = 1,5 m / s
2
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91

Parkside 95929 Translation Of Original Operation Manual

Kategória
Elektrické náradie
Typ
Translation Of Original Operation Manual
Táto príručka je tiež vhodná pre

V iných jazykoch