Silvercrest SQWP8000 1A1 Operation and Safety Notes

Kategória
Powerbanky
Typ
Operation and Safety Notes
QI POWER BANK
SQWP8000 1A1
IAN 305944
QI POWER BANK
Operation and Safety Notes
POLNILNA BATERIJA
POWERBANK QI
Delovanje in varnostna navodila
QI-POWERBANKA
Pokyny pro obsluhu a bezpečnostní
pokyny
QI-POWERBANK
Bedienungs- und Sicherheitshinweise
GB Operation and Safety Notes Page 5
SI Delovanje in varnostna navodila Stran 22
CZ Pokyny pro obsluhu a bezpečnostní pokyny Strana 40
DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 57
QI-POWERBANK
SQWP8000 1A1
IAN 305944
QI-POWERBANK
Bedienungs- und Sicherheitshinweise
QI POWER BANK
Operation and Safety Notes
5
7
8
910
21 3
4
6
A
9
GB 5
Warnings and symbols used ....................... Page 6
Introduction................................................ Page 8
Intended use ................................................................Page 8
Trademark notice.........................................................Page 8
Scope of delivery ........................................................Page 9
Before use ....................................................................Page 9
Parts description ..........................................................Page 9
Technical specifications ..............................................Page 10
Safety notices ............................................. Page 11
Operation and use ..................................... Page 14
Charging the power bank ..........................................Page 14
Checking the battery status ........................................Page 14
Qi wireless charging ...................................................Page 15
Charging mobile devices with the power bank.........Page 16
Troubleshooting ......................................... Page 17
Cleaning and care....................................... Page 19
Storage during non-use .............................. Page 19
Disposal ..................................................... Page 19
Simplified EU declaration of conformity ...... Page 20
Warranty ................................................... Page 20
GB 6
Warnings and symbols used
These instructions for use contain the following symbols and
warnings:
DANGER! This symbol with the signal word
“DANGER“ indicates a hazard with a high
level of risk which, if not avoided, will result in
serious injury or death.
WARNING! This symbol with the signal
word “WARNING“ indicates a hazard with
a medium level of risk which, if not avoided,
could result in serious injury.
CAUTION! This symbol with the signal word
“CAUTION“ indicates a hazard with a low
level of risk which, if not avoided, could result
in minor or moderate injury.
ATTENTION! This symbol with the signal
word “Attention“ indicates a possible property
damage.
NOTE: This symbol with the signal word
“NOTE“ provides additional useful information.
This action sign indicates to wear suitable
protective gloves! Follow the instructions to
avoid hands striking or being struck by objects
or being in contact with thermal or chemical
materials!
GB 7
WARNING! EXPLOSION HAZARD!
A warning with this symbol and word
“WARNING! EXPLOSION HAZARD”
indicates the potential threat of explosion.
Failure to observe this warning may result in
serious or fatal injuries and potential property
damage. Follow the instructions in this warning
to prevent serious injuries, a danger to life or
property damage!
This symbol means that the operating
instructions must be observed when using the
product.
V
Voltage (direct current)
W
Watt (power)
“Qi“ and the Qi logo mark are trademark of
the Wireless Power Consortium (WPC)
Smart Fast Charge (SFC): Maximum current
available is used to optimise charging time.
GB 8
QI POWER BANK
P Introduction
We congratulate you on the purchase of your new product. You
have chosen a high quality product. The instructions for use are
part of the product. They contain important information concerning
safety, use and disposal. Before using the product, please
familiarise yourself with all of the safety information and instructions
for use. Only use the product as described and for the specified
applications. If you pass the product on to anyone else, please
ensure that you also pass on all the documentation with it.
Intended use
This QI POWER BANK (hereinafter referred to as “product”) is
an Information Technology device which is solely intended to be
used to charge mobile devices which have Qi wireless charging
technology. Devices that do not support Qi wireless technology
can be charged through a USB port. This product is not intended
for commercial use. Manufacturer is not liable for damages, which
result from non-intended use.
Trademark notice
USB
®
is a registered trademark of USB Implementers Forum, Inc.
“Qi“ and the Qi logo mark are trademark of the Wireless Power
Consortium (WPC)
The Smart Fast Charge trademark and trade name is the
property of their respective owners.
The SilverCrest trademark and trade name is the property of
their respective owners.
Any other names and products are trademarks or registered
trademarks of their respective owners.
GB 9
Scope of delivery
1 Qi Power bank
1 USB cable
1 Instructions for use
Before use
Note: Remove all packaging materials from the product.
Please also check the content of delivery inside the packaging
to see if there are any damages. If you notice any damage or
missing parts, please contact the dealer who sold this product.
Parts description
Please refer to the fold out page.
1
Micro USB input
6
Battery status indicator
2
USB type A output
7
Qi charging surface
3
USB type C input and output
8
Powerbank
4
Qi status indicator
9
USB cable
5
On/off button
10
Instruction for use
GB 10
Technical specifications
Built-in rechargeable battery:
3.7 V
, 8000 mAh,
29.6Wh (Lithium polymer)
Micro-USB input voltage / current:
5 V
, 2.1 A
USB Type C input and ouput
voltage / current:
5 V
, 3 A
USB Type A output
voltage / current:
5 V
, 2.1 A
Qi Wireless output (1 coil)
voltage / current:
5 V
, 1 A
Wireless charging power: 5 W
Wireless charging distance: ≤ 5 mm
Charging efficiency: up to 65%
Frequency band: 106.4 - 173.8 kHz
Transmitted maximum radio
frequency power (H-field):
-10 dBuA/m at 10m distance
Total maximum output power:
15 W*
Total maximal output current: 3 A*
Minimal output current: approx. 50 mA
Operating temperature: 5 – 35 °C
Storage temperature: 0 – 45 °C
Humidity (no condensation): 10 – 70 %
Dimensions: approx. 145 x 72 x 17 mm
Weight: approx. 195 g
*If all outputs are used at the same time, the sum of the output
current must not exceed 3 A.
GB 11
Notes on Qi technology:
This product with Qi wireless charging is designed to comply with
the Qi (Wireless Power Consortium) standard, but no guarantees
are given for its compatibility with all products that comply with the
standard.
Safety notices
Please familiarise yourself with all instructions for use and Safety
notices before using the product for the first time. When passing
this product on to third parties, please be sure to include all
documentation.
Check the product for visible external damage before use. Do
not use the product if damaged or dropped.
This product may be used by children age 8 years and up, as
well as by persons with physical, sensory or mental impairments
or lacking experience and/or knowledge, provided they are
supervised or instructed in the safe use of the product and
understand the associated risks. Do not allow children to play
with the product. Never allow children to clean or maintain this
product unsupervised.
DANGER Packaging materials are not a toy. Keep all
packaging materials out of the reach of children. Suffocation
hazard!
Always use the product on flat and smooth surface. The product
could be damaged if it falls.
Do not expose the product to direct sunlight or high
temperatures. It may otherwise overheat and be damaged
beyond repair.
Do not operate the product near heat sources such as radiators
or other devices producing heat.
Do not operate the product near open flames.
The product is not designed for use in rooms with high
temperatures or humidity (i.e bathrooms) or those in which a
great amount of dust is generated.
GB 12
Do not expose the product to dripping water or splashing water
and do not place containers filled with liquids such as vases or
open drinks on top of or beside the product.
Do not expose the product to extremely high temperatures. This
applies in particular if you are thinking about storing the product
in your car. Over a prolonged period of time, the car and
the glove compartment could become extremely hot. Remove
electric and electronic devices from the car.
Do not use the product immediately after it has brought from
a cold room to a warm room. Allow the product to acclimatise
before you switch it on.
DANGER Never open the product casing. This product
has no internal parts requiring maintenance.
Do not independently convert or modify the product.
Repairs to the product must be performed by authorised
specialised companies or customer service. Improper repairs
may place the user in considerable danger. They will also void
the warranty.
WARNING Metal objects between the charger and device
to be charged will get hot and can burn you. Remove foreign
objects from the charger before charging device.
DANGER Improper handling of lithium polymer batteries
can result in fire, explosions, hazardous substances leaking, or
other dangerous situations! Do not throw the product into the
fire, as this could lead to the built-in battery exploding.
Observe the usage restrictions and prohibitions of use for
battery-operated products in situations which may be hazardous
such as at petrol stations, airports, hospitals, etc.
WARNING During charging process, please be noticed
that the product must not be covered. Otherwise the product can
be heated.
The product should never be charged at a PC or notebook,
because due to the high power consumption, the PC or
notebook could be damaged.
NOTE:
Do not attach a metal object to the Qi charging surface.
GB 13
Do not charge when the Qi wireless charger is covered with a
towel, layer of dust, etc.
Do not allow the Qi charging surface to get wet from water,
beverages, etc.
Do not use the Qi charging surface if it is malfunctioning.
Immediately switch the product off and remove the charging
cable from the product if you smell burning or see smoke. Have
the product examined by a qualified technician before using it
again.
Do not subject the Qi charging surface with a strong forces or
impact. Failure to do so may result in damage, injury and/or
malfunction.
Do not place magnetic recording media inside the charging
area during charging. The magnetism generated may erase the
data on credit cards. It may also cause wristwatches and other
precision instruments to malfunction.
During charging and immediately after charging, the Qi
charging surface and mobile device will be warm. This is normal
and not a malfunction. If there is an unusual heating, check the
Qi charging surface and mobile device.
Always place only one mobile device to charge on the Qi
charging surface. Only one device can be charged at a time.
Compatibility with all Qi devices cannot be guaranteed.
Do not attach an anti-slip mat or stickers to the Qi charging
surface. The presence of an anti-slip mat or stickers between the
mobile device to be charged and the Qi charging surface that
may prevent charging start.
If a cover or decorative accessory that does not comply with
the Qi wireless power standard has been attached to the
supported device, it may not be possible for the device to be
charged depending on the material, thickness, etc. of the cover
or accessory. In such cases, remove the attached cover or
accessory.
If charging does not start even after the supported device has
been placed in the charging area, place the device near the
[Qi] mark in the center of the charging area.
Before starting with wireless charging, read the instructions
provided with the mobile device as well.
GB 14
If you use a USB power supply, the socket used must always be
easily accessible so that the USB power supply can be quickly
removed from the socket in the case of emergency. Please also
refer to the manufacturer‘s instruction manual.
ATTENTION Two Qi charging devices and/or power banks
must never be placed on top of each other with the charging
surface. A device defect is the possible consequence.
P Operation and use
Charging the power bank
The built-in rechargeable battery must be fully charged before using
the product.
To charge the power bank
8
only use power supplies with an
output voltage of 5 V and an output current of at least 3 A.
ATTENTION The power bank must not be charged from a
PC or notebook.
Connect the USB cable
9
with the Micro-USB input port
1
of
the power bank
8
.
Connect the other end of the USB cable
9
(USB Type A) to a
USB power supply (not included in the scope of delivery) (see
fig. A).
ATTENTION Do not connect any device to the Powerbank for
charging while the Powerbank itself is charging.
Checking the battery status
You can check the battery status on the battery status indicator
6
of the power bank
8
at anytime.
Briefly press the ON / OFF button
5
. The battery status
indicator
6
shows the approximate charge status of the internal
battery in percent for approx. 30 seconds.
GB 15
1 LED lights up = 25 %
2 LEDs lights up = 50 %
3 LEDs lights up = 75 %
4 LEDs lights up = 100 %
Qi wireless charging
Put your Qi compatible device to be charged on the centre of
the Qi charging surface
7
of the power bank
8
.
Charging starts automatically when the Powerbank is switched
on. When Qi charging is active, Qi status indicator
4
lights
green.
Slightly adjust the charging position of the device to be charged
so that its charging surface is facing down to the centre of the Qi
charging surface
7
of the power bank
8
.
If wireless charging does not start, move your device to be
charged more accurately to the centre of the Qi charging
surface
7
.
While in idle status (standby mode), the Qi status indicator
4
will illuminate amber in colour.
When the charging process has finished the Qi status indicator
4
will still illuminate green in colour*.
The Qi status indicator
4
also shows quick flashing when the
power bank cannot detect any Qi charging device on the Qi
charging surface
7
. In this case, move your Qi compatible
device to be charged towards the center of Qi charging surface
7
in order to start wireless charging.
*
NOTE:
1) Qi status indicator
4
may change back to amber colour
(standby mode) when wireless charging has finished if the
mobile device closed the wireless communication between the
Qi charging surface
7
and the mobile device.
2) All devices to be charged must be comply with Qi Standard.
GB 16
Charging mobile devices with the power
bank
You can charge up to three devices at the same time using the
power bank
8
. If all outputs are used at the same time, the sum of
the output current must not exceed 3 A.
Connect the USB cable
9
or the original charging cable of
the device to be charged to the USB output
2
. Then connect
Micro-USB port of the USB Cable
9
to the Micro-USB input
of device to be charged. The charging process will start
automatically.
If your mobile device has a USB type C input, you can use a
type C to type C connection cable (not included) to connect
your device’s type C input to this power bank’s USB Type C
output
3
. The charging process will start automatically.
At the same time, you can place the device to be charged on the
Qi charging surface
7
.
In case if the charging process does not begin immediately,
press the ON / OFF button
5
briefly to begin the charging
process. The current battery status of the power bank
8
is
displayed during the charging process by the battery status
indicator
6
.
To end the charging process, disconnect the USB charging cable
from the mobile device and the power bank
8
. The power
bank will switch OFF and battery status indicator
6
will switch
off after approx. 30 seconds.
Or simply double click the ON / OFF button
5
. The power
bank
8
will switch off.
NOTE:
If you use both USB ports, a voltage of 5 V will be output at both
outputs. The maximum output current must not exceed 3 A for both
outputs.
GB 17
P Troubleshooting
= Problem
= Cause
= Solution
It may not be possible to charge a Qi compatible
device.
The mobile device is already fully charged.
Take away the fully charged device for use, until its internal
battery was drained again. Then put device back to Qi charging
surface
7
for charging.
The mobile device has become very hot as a result of charging.
Remove the mobile device from the wireless charging surface
7
for a few hours to let it cool down, and also check if your
product was damaged.
This product is in a location where strong radio waves or noise
is being generated, such as TV towers, electric power plants, or
gas stations.
Under this environment, use other output port, such as USB Type
C or Type A port for charging up your mobile device.
The power bank
8
is not being charged.
It may be that the power bank is not connected properly.
Check that it is connected.
In order to charge the power bank, a power supply with 5 V
and at least 3 A has to be used.
A connected device is not being charged.
The battery is drained.
Charge the battery.
The device is not connected.
GB 18
The device is not connected. Check that it is connected. Briefly
press the ON / OFF button
5
to begin the charging process.
The current consumption of the connected device might be too
low.
Check with your connected device manual and see if your
connected device current consumption comply with this product.
The minimal output current of the power bank is approx. 50 mA.
The power bank
8
does not react when the button
is pressed or when a device is connected, even
though the battery is charged.
The power consumption of the connected devices is too high.
Therefore, the internal overcurrent protection device was
activated.
Reduce the number of devices connected and press the ON /
OFF button
5
.
Wireless charging did not start
Device to be charged is not placed at the Centre of the Qi mark
location.
Make sure your device to be charged is at the correct position
at the centre of the Qi charging surface
7
of the power bank
8
.
Make sure that there are no other objects on the charging pad.
Remove your device‘s protective case as it may be blocking the
wireless signal.
Wireless charging speed slow
Device to be charged is too far away from the centre of the Qi
charging surface
7
.
Make sure your device to be charged is at the correct position at
the centre of the Qi charging surface
7
of the power bank
8
.
GB 19
P Cleaning and care
This product has no internal parts requiring maintenance. Moisture
entering the product may result in damage.
Do not wipe the Qi charging surface with oils, alcohol, benzine,
thinners, etc. or expose it to hair sprays, insecticide sprays, etc
If the Qi charging surface becomes dirty, wipe off the dirt using
a clean damp cloth.
Ensure no moisture enters the product during cleaning to prevent
damaging the product beyond repair.
Do not use abrasive, solvent-based or aggressive cleaners. These
can damage the surface of the product.
Only clean the product with a slightly damp cloth and mild
washing-up liquid.
P Storage during non-use
Store the product in a dry dust-free location, protected from
direct sunlight.
If the product is not used for a long time, the built-in battery
should be fully charged to prolong its operating life. Regularly
charge the built-in battery if you do not use the product for a
long period of time. This is necessary to preserve the battery.
P Disposal
Packaging:
The packaging is made of environmentally friendly materials, which
may be disposed of through your local recycling facilities.
Product:
Contact your municipality for information on how to dispose of your
worn-out product.
GB 20
The adjacent symbol of a crossed out dustbin on wheels
indicates this product is subject to Directive 2012/19/EU.
This directive states at the end of the life this product must
not be disposed of through regular household refuse but
must be returned to special collection sites, recycling depots or
waste management companies.
This disposal is free of charge to you.
Protect the environment and dispose of properly.
The product is recyclable, subject to extended manufacturer
responsibility, and collected separately.
The built-in rechargeable battery cannot be removed for disposal.
Return the product completely to a collection site for used
electronics.
P Simplified EU declaration of
conformity
Hereby, OWIM GmbH & Co. KG, Stiftsbergstraße 1, DE-74167
Neckarsulm, GERMANY, declares that the product QI POWER
BANK HG04127A, HG04127B, is in compliance with Directives
2014/53/EU and 2011/65/EU.
The full text of the EU declaration of conformity is available at the
following internet address: www.owim.com
P Warranty
The product has been manufactured to strict quality guidelines
and meticulously examined before delivery. In the event of product
defects you have legal rights against the retailer of this product.
Your legal rights are not limited in any way by our warranty
detailed below.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75

Silvercrest SQWP8000 1A1 Operation and Safety Notes

Kategória
Powerbanky
Typ
Operation and Safety Notes

V iných jazykoch