Silvercrest 275101 Assembly, Operating And Safety Instructions

Typ
Assembly, Operating And Safety Instructions
PREMIUM WIRELESS DOORBELL
IAN 275101
ZVONČEK
Pokyny pre montáž, obsluhu a bezpečnostné
pokyny
DESIGN-FUNKTÜRKLINGEL
Montage-, Bedienungs- und Sicherheitshinweise
DIZAJNERSKI BREZŽIČNI
ZVONEC
Navodila za montažo, uporabo in varnostna
navodila
DESIGNOVÝ BEZDRÁ TOVÝ
ZVONEK
Pokyny k montáži, obsluze a bezpečnostní
pokyny
PREMIUM WIRELESS DOORBELL
Assembly, operating and safety instructions
RÁDIÓS AJTÓCSENGŐ
Szerelési, használati és biztonsági tudnivalók
GB Assembly, operating and safety instructions Page 5
HU Szerelési, használati és biztonsági tudnivalók Oldal 20
SI Navodila za montažo, uporabo in varnostna navodila Stran 35
CZ Pokyny k montáži, obsluze a bezpečnostní pokyny Strana 51
SK Pokyny pre montáž, obsluhu a bezpečnostné pokyny Strana 65
DE / AT / CH Montage-, Bedienungs- und Sicherheitshinweise Seite 80
You need
Szüksége van
Potrebujete
Potřebujete
Budete potrebovať
Sie benötigen:
ø 6 mm
A
1
6
2
3
4
9
10
5
7
HG00783A HG00783B
B
8
6
C1
181211
15
D
C2
7
16
14 13
17
E
17
16
F
14
G
18
12
H
12 18
19
C B A
4 - 12V, AC/
4 - 12V, DC
I
J
5 GB
Introduction .............................................................................Page 6
Intended use ................................................................................. Page 6
Parts and features ........................................................................Page 6
Included items ..............................................................................Page 7
Technical data ..............................................................................Page 8
Safety ........................................................................................... Page 8
General safety information .........................................................Page 9
Safety instructions for batteries ...................................................Page 9
Assembly ...................................................................................Page 10
Preparing for use ................................................................Page 11
Inserting / replacing the batteries ................................................Page 11
Synchronising transmitter / receiver ............................................Page 12
Setting the signal type .................................................................Page 13
Setting the volume ........................................................................Page 13
Selecting the chime ...................................................................... Page 14
The procedure for connecting the transmitter to existing
bell system or existing doorbell button ....................................... Page 14
Connecting the transmitter to a existing
bell system ...............................................................................Page 15
Connecting a existing doorbell button ...............Page 15
Troubleshooting ...................................................................Page 16
Cleaning and maintenance .......................................... Page 16
Disposal ...................................................................................... Page 17
Declaration of conformity ............................................Page 18
Warranty ................................................................................... Page 18
6 GB
Premium Wireless Doorbell
Introduction
We congratulate you on the purchase of your new device. You have
chosen a high quality product. The instructions for use are part of the
product. They contain important information concerning safety, use
and disposal. Before using the product, please familiarise yourself
with all of the safety information and instructions for use. Only use the
unit as described and for the specified applications. If you pass the
product on to anyone else, please ensure that you also pass on all
the documentation with it.
Intended use
This product is intended for the wireless transmission of the doorbell
signal. The product is not intended for commercial use.
Parts and features
Receiver
1
Signal indicator
2
Speaker
3
Signal type selector button
(optical, acoustic, optical and acoustic signal)
4
Melody selection button
7 GB
5
Volume / Synchronisation button
6
Battery compartment cover
7
Hanger
8
Battery compartment
Transmitter
9
Chime button
10
Name plate
11
Lock
12
Holder (for wall mounting)
13
Battery compartment
14
Inner cover
Mounting
15
Rubber cover
16
Screw
17
Dowel
18
Cable exit hole
19
Cable holder
Included items
1 Transmitter
1 Receiver
3 Batteries 1.5 V
, type AA (receiver)
1 Battery 3 V
, type CR2032 (transmitter)
3 Screws (for transmitter and for mounting the receiver on a wall)
8 GB
3 Dowels
5 Name plates (for the doorbell)
1 Operating instructions
Technical data
Range: 150 m (unobstructed area)
Transmission frequency: 434 MHz
Battery types: Receiver: 3 x 1.5 V
(type AA / LR6),
Transmitter: 1 x 3 V
(type CR2032)
Receiver: Audible signal volume (at maximum
volume setting): approx. 73 dB (at a
distance of 1 m from the device)
Ingress protection rating
of the transmitter: IP44 (splash water proof)
Safety
Read all safety information and instructions!
STORE ALL SAFETY INFORMATION AND INSTRUCTIONS IN A
SAFE PLACE IN CASE YOU NEED TO REFER TO THEM AGAIN
IN THE FUTURE!
9 GB
General safety information
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental ca-
pabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
Check that all parts are in sound condition. If you use damaged
parts when assembling the device, you risk injury.
Safety instructions for batteries
DANGER TO LIFE! Batteries can be swallowed,
which can prove fatal. Consult a doctor immediately if anyone
swallows a battery.
EXPLOSION HAZARD! Never recharge non-
rechargeable batteries, short-circuit and / or open bat-
teries. This can cause them to overheat, burn or burst.
Never throw batteries into fire or water. The batteries may explode.
Immediately remove depleted batteries from the device; other-
wise there will be an increased risk of leakage!
Always replace all the batteries at the same time and insert
batteries of the same type.
10 GB
Do not use different types of batteries or mix used and new
batteries together.
Batteries do not belong in household refuse. Dispose of used
batteries in an environmentally friendly manner.
Consumers are under a legal obligation to dispose of batteries in
the proper way.
Keep the battery out of the reach of children, do not dispose of
the battery in fire, do not short-circuit it, and do not take it apart.
Failure to observe these instructions may result in the battery dis-
charging beyond its end voltage, which poses a risk of leakage.
If the battery in your instrument has leaked, have it removed im-
mediately to prevent damage to the instrument.
Avoid contact with skin, eyes and mucous membrane. In the event
of contact with battery acid, rinse the affected area with plenty of
water and / or consult a doctor.
Never use rechargeable batteries.
The supply terminals are not to be short-circuited.
Do not mix old batteries with new ones.
Remove the batteries from the device if they have not been used
for a long period.
Make sure you insert the batteries the right way round (polarity).
Assembly
Note: You will need a screwdriver and a drill to assemble the
doorbell.
11 GB
Note: Only use the screws and dowels supplied for the assembly of
the device.
Mount the receiver (see Fig. D)
Mount the transmitter (see Fig. E)
Preparing for use
Inserting / replacing the batteries
Insert the batteries to provide power to the device before prepar-
ing it for use.
CAUTION! Use the indicated battery types only. Failure to ob-
serve this advice may result in damage to the product.
Receiver (see Fig. B):
Remove the battery compartment cover
6
from the back of the
device.
Remove the used batteries, if present.
Insert 3 batteries (1.5 V
, type AA).
Note: Ensure correct polarity. This is indicated in the battery
compartment
8
.
Close the battery compartment
8
.
Transmitter:
Remove the holder
12
by pressing the lock
11
from the back of
the transmitter and remove the rubber cover
15
(see fig. C1).
12 GB
Remove the used batteries, if present (see fig. C2).
Insert a battery (3 V
, type CR 2032). The side marked “+”
must face upwards.
Install the rubber cover
15
, close the holder
12
of the transmitter
back on to the back of the device.
Synchronising transmitter / receiver
The doorbell works on 434 MHz which is a quite common fre-
quency. To ensure that the function gets no influenced be doorbells in
the neighborhood, the transmitter and the receiver hence have to be
synchronized in regard of the encryption. Every transmitter is working
with a different encryption of the signal.
Synchronise the transmitter and receiver as follows:
As soon as the batteries are installed, the receiver enters synchro-
nizing mode for approx. 1 minute. During the synchronizing
mode, the signal indicator
1
steadily lights up in blue color.
You can also manually enter synchronising mode by holding the
synchronising button
5
for approx. 3 seconds.
The signal indicator
1
on the receiver will steadily light up for
approx. 1 minute, to indicate that the receiver is in synchronizing
mode.
Press the chime button
9
of the transmitter, while the receiver is
in synchronise mode. If the receiver receives the signal, the steady
blue light of the signal indicator
1
flickers 6 times to indicate
that the synchronization is successful.
13 GB
Setting the signal type
The receiver can indicate the reception of a door signal either both
optically and acoustically, acoustically or optically.
Using the signal type selector button
3
, select whether the
signal is to be indicated both optically and acoustically or acous-
tically or optically.
Press the signal type selector button
3
once. An acoustical
signal will sound up and the afterwards the signal indicator
1
will flash. The receiver will now indicate the door signal acousti-
cally and optically. Press again the signal type selector button
3
.
An acoustical signal will sound. The receiver will now indicate the
door signal acoustically. Press again the signal type selector
button
3
. The receiver will now indicate the door signal in an
optical way.
Setting the volume
Press the volume button
5
until the desired volume is reached.
There are a total of 4 possible volume settings: very loud, loud,
medium, soft.
14 GB
Selecting the chime
Note: The doorbell has 16 different chimes.
Press the melody selection button
4
. The first audible signal
sounds.
Press the melody selection button
4
again to move on to the
next audible signal.
Repeat this process until you have selected your desired audible
signal. The last-selected audible signal is automatically stored.
The procedure for connecting the
transmitter to existing bell system or
existing doorbell button
Remove the holder
12
by pressing the lock
11
from the back of
the transmitter and remove the rubber cover
15
(see fig. C1).
Open the inner cover
14
by cross head screw driver (see fig. F).
Remove the plastic clip of cable exit hole
18
with a flat head
screw driver (see fig. G).
Insert the cable through cable holder
19
and cable exit hole
18
(see fig. H).
Connect cable to the terminals A and C (for connecting to exist-
ing doorbell) or the terminals B and C (for connecting to existing
door bell button) by using screw driver (see fig. H).
15 GB
Connecting the transmitter
to a existing bell system (see Fig. I)
Extension of an already existing doorbell system:
An already existing doorbell system can be extended with this wire-
less doorbell.
The operating voltage of the doorbell system must be between 4–12 V.
It makes no difference whether this comes from direct current or 50 Hz
alternating current. In the event that you are dealing with an existing
doorbell system using direct current, you must connect the positive ter-
minal of the doorbell to contact C of the transmitter and the negative
terminal to contact A of the transmitter.
IMPORTANT! Never reverse polarity. This can damage the device.
The connection terminals A and C, found on the circuit board of the
transmitter as shown in fig. I must be connected directly to the electri-
cal connection terminals of the signal generators (e.g. bell). The
button of the transmitter may also be used for this type of operation.
Note: Contact a qualified electrician in case of problems during
installation.
Connecting a existing
doorbell button (see Fig. J)
The separate bell button must not be connected to the existing door-
bell system. The battery must remain in the transmitter. The B and C
16 GB
terminals are to this purpose with a two-core cable connected to the
bell push. The bell push may only be connected to the transmitter.
Troubleshooting
After the influence of extraordinary environmental conditions (e.g. a
strong electromagnetical field) the function of the item may be af-
fected. In this case, please take off the batteries of both appliances
for approximately 2 minutes. Then proceed again as described in the
section “Synchronising the transmitter / receiver”.
Electrostatic discharges may lead to malfunctions. If such malfunctions
do occur, remove the battery for a short time and then replace it again.
Then proceed again as described in the section “Synchronising the
transmitter / receiver”.
Cleaning and maintenance
Under no circumstances should you use liquids or detergents, as
these will damage the device.
The device should only be cleaned on the outside with a soft dry
cloth.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99

Silvercrest 275101 Assembly, Operating And Safety Instructions

Typ
Assembly, Operating And Safety Instructions

V iných jazykoch