Parkside PWS 125 A1 ANGLE GRINDER Translation Of Original Operation Manual

Značka: Parkside

Model: PWS 125 A1 ANGLE GRINDER

Kategória: Elektrické náradie

Typ: Translation Of Original Operation Manual

IAN 102828

ANGLE GRINDER PWS 125 A1

ANGLE GRINDER

Translation of original operation manual

KOTNI BRUSILNIK

Prevod originalnega navodila za uporabo

SAROKCSISZOLÓ

Az originál használati utasítás fordítása

SZLIFIERKA KĄTOWA

Tłumaczenie oryginalnej instrukcji obsługi

UHLOVÁ BRÚSKA

Preklad originálneho návodu na obsluhu

ÚHLOVÁ BRUSKA

Překlad originálního provozního návodu

WINKELSCHLEIFER

Originalbetriebsanleitung

GB Translation of original operation manual Page 1

PL Tłumaczenie oryginalnej instrukcji obsługi Strona 15

HU Az originál használati utasítás fordítása Oldal 31

SI Prevod originalnega navodila za uporabo Stran 45

CZ Překlad originálního provozního návodu Strana 59

SK Preklad originálneho návodu na obsluhu Strana 73

DE / AT / CH Originalbetriebsanleitung Seite 87

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of

the device.

Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi

funkcjami urządzenia.

Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik

funkcióját.

Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.

Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.

Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

PWS 125 A1

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

General Power Tool Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1. Work area safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2. Electrical safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3. Personal safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

4. Power tool use and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

5. Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Safety advice for all uses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Safety advice relating to kickback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Special safety advice relating to grinding and disc-cutting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Further special safety advice for disc-cutting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Special safety advice for abrading using sandpaper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Special safety advice for polishing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Special safety advice for working with wire brushes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Safety advice for angle grinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Working procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Adjusting the blade guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Using the additional handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Switching on and oﬀ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Setting the rotational speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Changing grinding tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

General information about the supplied grinding tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Storage and handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Before using the grinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Using accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Cutting/rough grinding discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Flap buﬀ er discs for metal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Additional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Maintenance and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Importer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Translation of the original Conformity Declaration . . . . . . . . . . . . . . . . . . . . . 13

IB_102828_PWS125A1_LB4.indb 1 22.08.14 12:03

PWS 125 A1

ANGLE GRINDER PWS 125 A1

Introduction

Congratulations on the purchase of your

new appliance. You have selected a high-

quality product. The operating instructions

are part of this product. They contain

important information on safety, usage

and disposal. Before using the product, familiarise

yourself with all operating and safety instructions.

Use the product only as described and for the

areas of applications speciﬁ ed. Please also pass

these operating instructions on to any future

owner(s).

Intended use

The appliance is intended for cutting, rough cutting

and brushing metal work materials without the use

of water. Any other usage of or modiﬁ cation to the

appliance is deemed to be improper usage and

carries the risk of serious personal injury. The manu-

facturer accepts no responsibility for damage(s)

resulting from improper usage.

The appliance is not meant for commercial use.

NOTE

►

Slots in load-bearing walls are subject to

the standard DIN 1053 part 1 or country-

speciﬁ c regulations. These provisions must be

strictly adhered to. Please seek the advice of

the responsible structural engineer, architect,

or the supervising construction management.

Features

Safety lock-out

ON/OFF switch

Cover for carbon brushes

Additional handle

Adjustable blade guard

Tensioning nut

Mounting spindle

Mounting ﬂ ange

Metal cutting disc

Spindle locking button

Rotational speed preselector adjusting wheel

Spanner (Fig. B)

Screws

Package contents

1 angle grinder PWS 125 A1

1 metal cutting disc

1 additional handle

1 blade guard

1 spanner

1 operating instructions

Technical data

Nominal load: 1200 W

Rated voltage: 230–240V

50Hz

Rated speed: n 12000 min

-1

Continuously variable

rotational speed: 3000–12000 min

-1

Spindle thread: M14

Protection class: II /

Noise and vibration data:

Noise measurement value determined in accordance

with EN 60745 The A-rated noise level of the

power tool is typically:

Sound pressure level: L

= 91 dB (A)

Uncertainty: K = 3 dB (A)

Sound power level: L

= 102 dB (A)

Uncertainty: K = 3 dB (A)

Vibration values:

Angle grinding

(main handle): a

h, AG

= 13.431 m/s

Angle grinding

(additional handle): a

h, AG

= 9.770 m/s

Uncertainty: K = 1.5 m/s

Wear ear protection!

NOTE

►

The vibration level speciﬁ ed in these instruc-

tions has been measured in accordance

with the standardised measuring procedure

speciﬁ ed in EN 60745 and can be used to

make equipment comparisons. The speciﬁ ed

vibration emission value can also be used to

make an initial exposure estimate.

IB_102828_PWS125A1_LB4.indb 2 22.08.14 12:03

PWS 125 A1

WARNING!

► The vibration level varies in accordance with

the use of the tool and may be higher than

the value speciﬁ ed in these instructions in

some cases. It is easy to underestimate the

vibration load if the electrical power tool is

used regularly in this manner. For an accurate

estimate of the vibration load during a certain

working period, the times during which the

appliance is switched oﬀ or is running but not

actually being used must also be taken into

consideration. This can signiﬁ cantly reduce

the vibration load over the total working

period.

Explanation of the symbols on the appliance!

Read the original operating

instructions and safety instruc-

tions before initial operation.

Wear ear protection!

Wear protective glasses!

Wear sturdy work boots!

Wear protective gloves!

Wear a dust mask!

Not approved for wet grinding

Not approved for side grinding

Using damaged cutting or

grinding discs is dangerous

and may cause serious injury!

General Power Tool

Safety Warnings

WARNING!

► Read all safety warnings and all instructions.

Failure to follow the warnings and instructions

may result in electric shock, ﬁ re and/or serious

injury.

Save all warnings and instructions for future

reference.

The term “power tool” in the warnings refers

to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

1. Work area safety

a) Keep work area clean and well lit. Cluttered

or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of ﬂ am-

mable liquids, gases or dust. Power tools create

sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

2. Electrical safety

a) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiﬁ ed plugs and matching outlets

will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

IB_102828_PWS125A1_LB4.indb 3 22.08.14 12:03

PWS 125 A1

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD

reduces the risk of electric shock.

3. Personal safety

a) Stay alert, watch what you are doing and

use common sense when operating a power

tool. Do not use a power tool while you are

tired or under the inﬂ uence of drugs, alcohol

or medication. A moment of inattention while

operating power tools may result in serious

personal injury.

b) Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat,

or hearing protection used for appropriate

conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ -position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools

with your ﬁ nger on the switch or energising

power tools that have the switch on invites

accidents.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool

may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used.

Use of dust collection can reduce dust-related

hazards.

4. Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at

the rate for which it was designed.

b) Do not use the power tool if the switch does not

turn it on and oﬀ . Any power tool that cannot

be controlled with the switch is dangerous and

must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may aﬀ ect the

power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

g) Use the power tool, accessories and accessory

tools etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed. Use of the

power tool for operations diﬀ erent from those

intended could result in a hazardous situation.

5. Service

a) Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

b) Always arrange for the exchange of the plug

or the power cord to be carried out by the

manufacturer of the appliance or by its ap-

proved customer services. This will ensure that

the safety of the power tool is maintained.

IB_102828_PWS125A1_LB4.indb 4 22.08.14 12:03

PWS 125 A1

Safety advice for all uses

General safety advice for grinding, sanding

(with sandpaper), wire brushing, polishing

and disc-cutting:

a) This electrical power tool is intended for use as

a grinding, sanding, wirebrushing, and disc-

cutting machine. Observe all the safety advice,

instructions, information in ﬁ gures and all other

information you received with this device.

If you do not observe the following advice it could

lead to electric shock, ﬁ re and /or serious injury.

b) Do not use any accessory not speciﬁ cally

intended by the manufacturer for this electrical

power tool. Although an accessory may ﬁ t on

your electrical power tool, this does not on its

own guarantee that it can be safely used.

c) The maximum permitted speed of an attach-

ment must be at least as high as the maximum

speed indicated for the electrical power tool.

An accessory rotating faster than its permitted

speed could disintegrate or ﬂ y oﬀ .

d) The external diameter and the thickness of the

attachment must be compatible with the dimen-

sions of your electrical power tool. Attachments

that are not dimensionally compatible cannot be

adequately guarded or controlled.

e) Grinding discs, ﬂ anges, grinding wheels or

other accessories must ﬁ t exactly on to the

spindle of your electrical power tool. Attach-

ments that do not exactly ﬁ t on the spindle turn

unevenly, vibrate severely and could lead to

loss of control.

f) Do not use damaged attachments. Before

every use check attachments such as grind-

ing discs for loose fragments and cracks,

grinding wheels for cracks, deterioration or

excessive wear and wire brushes for loose or

broken wires. If the electrical power tool or

attachment is dropped, inspect for damage

or change the attachment for an undamaged

one. When you have inspected and inserted

the attachment, position yourself and by-

standers away from the plane of the rotating

attachment and run the device at maximum

speed for one minute. Damaged attachments

will usually break apart during this test.

g) Wear personal protective equipment. Use

a full face visor, safety goggles or safety

glasses, depending on the application. Wear

a dust mask, hearing protectors, safety

gloves or special apron capable of stopping

particles of the grinding medium or work-

piece, as appropriate for the task. Eyes must

be protected from the ﬂ ying debris which can

arise from some operations. Dust or breathing

masks must be capable of ﬁ ltering out the dust

generated by the application. Prolonged expo-

sure to loud noise can lead to hearing loss.

h) Keep bystanders at a safe distance from your

work area. Anyone entering the work area

must wear personal protective equipment.

Fragments of the workpiece or of a broken at-

tachment could ﬂ y oﬀ and cause injury beyond

the immediate working area.

i) Hold the device by the insulated handle sur-

faces when you are undertaking work where

there is the danger of the attachment striking

hidden electricity cables or the device’s mains

lead. Contact with a live wire could cause

metal parts of the device to become live and

lead to electric shock.

j) Keep the power cord away from rotating

attachments. If you lose control of the device the

mains lead may become severed or trapped and

your hand or arm may be pulled into the rotating

attachment.

k) Never lay the electrical power tool down until

after the attachment has come to a complete

standstill. The rotating attachment may snag

when it comes into contact with the surface and

cause you to lose control of the device.

l) Do not have the electrical power tool running

while you are carrying it. Your clothing could

become trapped by unintentional contact with

the rotating attachment and the tool could be

pulled into your body.

m) Clean the ventilation slots on your electrical

power tool regularly. The motor’s fan draws

dust into the housing. A build-up of metal dust

could give rise to an electrical hazard.

n) Never use the electrical power tool near in-

ﬂ ammable materials. Sparks could ignite these

materials.

IB_102828_PWS125A1_LB4.indb 5 22.08.14 12:03

PWS 125 A1

o) Do not use attachments that require the use

of coolants. The use of water or other liquid

coolants could result in electric shock.

Safety advice relating to kickback

Kickback is the sudden reaction to a pinched or

snagged rotating attachment, such as a grinding

disc, grinding pad, wire brush etc. Pinching or

snagging results in the rotating attachment coming

to an abrupt stop. This causes the electrical power

tool (if not controlled) to move in the opposite di-

rection to the direction of rotation of the attachment

at the point of constraint.

If, for example, a grinding disc is pinched or snags

in a workpiece, this can cause the edge of the

grinding disc to penetrate the workpiece, become

trapped there and either free itself or kickback.

The grinding disc moves towards or away from the

operator, depending on the direction of movement

of the disc at the point of constraint. The grinding

disc could also break.

Kickback occurs as a result of incorrect use or mis-

use of the electrical power tool. It can be prevented

by taking the appropriate precautions as described

below.

a) Maintain a ﬁ rm grip on the electrical power

tool and position your body and arms to al-

low you to resist kickback forces. Always use

the auxiliary handle, if provided, to exercise

the greatest possible control over kickback

forces or reaction torques as the device builds

up to full speed. By taking suitable precautions

the operator can control kickback and reaction

forces.

b) Do not place your hands near a rotating

attachment. If kickback occurs the attachment

could move over your hand.

c) Avoid positioning your body in the area into

which the electrical power tool would move in

the event of a kickback. A kickback moves the

electrical power tool in the opposite direction to

the direction of movement of the grinding disc

at the point of constraint.

d) Work particularly carefully in the area of

corners, sharp edges etc. to avoid the attach-

ment bouncing or snagging on the work-

piece. Corners, sharp edges or bouncing have

a tendency to snag the rotating attachment. This

causes loss of control or kickback.

e) Do not use saw-chain woodcarving discs

or toothed discs. Such attachments create

frequent kickback and loss of control of the

electrical power tool.

Special safety advice relating to

grinding and disc-cutting

a) Always use the guard designed for the

type of abrasive consumable you are using.

Always use abrasive consumables approved

for use with your electrical power tool.

Abrasive consumables not approved for use with

your electrical power tool cannot be adequately

guarded and are unsafe.

b) To ensure the highest level of operational

safety, the disc guard cover must be attached

to the electrical power tool and set in such

a way that the smallest possible area of the

abrasive consumable is exposed to the opera-

tor. The disc guard cover is there to protect the

operator from pieces breaking oﬀ and acciden-

tal contact with the abrasive consumable.

c) Abrasive consumables must be used only for

their recommended purposes, For example:

never grind with the side face of a cutting

disc. Cutting discs are intended for removing

material using the edge of the disc. Sideways

forces on these abrasive consumables can

cause them to break.

d) Always use an undamaged mounting ﬂ ange

of the correct size and shape for your se-

lected grinding disc. Suitable ﬂ anges support

the grinding disc and reduce the chance of it

breaking. Flanges for cutting discs are diﬀ erent

from the ﬂ anges for other abrasive discs.

e) Never use worn down abrasive consumables

intended for larger electrical power tools.

Abrasive consumables intended for larger elec-

trical power tools are not designed for the faster

rotational speeds of these smaller electrical

power tools and could break.

IB_102828_PWS125A1_LB4.indb 6 22.08.14 12:03

PWS 125 A1

Further special safety

advice for disc-cutting

a) Avoid snagging the cutting disc and do not use

too much contact pressure. Do not attempt to

make excessively deep cuts. Overloading the

cutting disc increases the load and the tendency

of the disc to twist or snag in the cut, making

kickback or disc breakage more likely.

b) Avoid the area in front of or behind the rotat-

ing cutting disc. If the cutting disc is moving

away from you at the point of constraint in the

workpiece, then, in the event of a kickback, the

electrical power tool and the rotating disc may

be thrown towards you.

c) If the cutting disc jams or you stop work for

a while, switch the device oﬀ and hold it until

the disc comes to a complete stop. Never at-

tempt to pull the still rotating cutting disc out

of the cut as this could cause kickback. Deter-

mine and rectify the reason for the jamming.

d) Do not switch on the device if the cutting disc

is in the workpiece. Allow the cutting disc to

reach full speed before carefully continuing

with the cut. Otherwise the disc could snag,

jump out of the workpiece or cause a kickback.

e) Support boards or workpieces whilst cutting

to reduce the risk of kickback caused by a

jammed cutting disc. Large workpieces may

bend under their own weight. The workpiece

must be supported to both sides of the cutting

disc and particularly near the cutting disc and

at the workpiece edge.

f) Be particularly careful when pocket cutting in

existing walls or other areas where you can-

not see what you are cutting into. The cutting

disc plunged into the surface could cut through

gas or water pipes, electricity cables or other

objects and cause kickback.

Special safety advice for

abrading using sandpaper

■ Do not use over-sized sanding sheets. Follow

the manufacturer’s recommendations for

sanding sheet size. Sanding sheets that project

beyond the backing pad could cause injury

in addition to jamming, tearing of the sheet or

kickback.

Special safety advice for polishing

■ Do not use the polishing bonnet if it has

any loose parts, in particular the fastening

cords. Tuck the fastening cords away or trim

them. Loose fastening cords rotating with the

attachment could catch your ﬁ ngers or become

trapped in the workpiece.

Special safety advice for working with

wire brushes

a) Bear in mind that wire brushes lose pieces of

wire during normal use. Do not overload the

wires by applying too much pressure. Flying

pieces of wire can very easily penetrate thin

clothing and / or skin.

b) Use a guard, if recommended, but make

sure that the wire brush does not come into

contact with the guard. The diameters of disc

brushes and cup brushes can increase due to

contact pressure and centripetal forces.

Safety advice for angle grinders

■ DANGER OF ELECTRIC SHOCK! Do not

operate the device if the mains lead or mains

plug is damaged.

■ DANGER OF ELECTRIC SHOCK! Do not

touch the mains lead if it becomes damaged

or cut through while you are using the device.

Pull the plug out of the mains socket immediate-

ly and have the device repaired by a suitably

qualiﬁ ed person or at your service centre.

■ DANGER OF ELECTRIC SHOCK! Do not oper-

ate the device if it is damp and do not use it in a

damp environment.

■ DANGER OF ELECTRIC SHOCK! If you

use the device outdoors, always connect it

through a residual current device (RCD) with

a maximum trip current of 30 mA. If using an

extension lead, always use one that is approved

for outdoor use.

■ Do not suspend or carry the device by the

mains lead. Always work with the mains lead

leading away from the rear of the device.

Otherwise the device could be damaged.

■ Grinding discs must be carefully kept and han-

dled in accordance with the manufacturer’s

instructions. Otherwise they could be damaged.

IB_102828_PWS125A1_LB4.indb 7 22.08.14 12:03

PWS 125 A1

■ Make sure that abrasive consumables and

tools are attached in accordance with the

manufacturer’s instructions and advice.

Otherwise they could become detached from

the device and result in injury and / or damage

to property.

■ Ensure that any spacers supplied and

required for the use of certain abrasive con-

sumables and tools are installed.

■ Do not use separate reducing bushes or

adapters in order to make grinding discs with

a larger bore ﬁ t.

■ When using abrasive consumables and tools

with a threaded insert make sure that the

tread is long enough for the spindle length.

Otherwise the grinding discs could become

detached from the device and result in injury

and / or damage to property.

■ Do not allow the end of the spindle to contact the

base of the hole in the abrasive consumable.

■ Do not work in areas where there may be

concealed electricity cables or gas or water

pipes. Use a suitable detector or ask your

local utility service providers. Contact with

electricity cables can lead to ﬁ re or electric

shock. Damaging a gas pipe can lead to an

explosion. Penetration of a water pipe can lead

to property damage or to electric shock.

WARNING! NOXIOUS FUMES!

► Working with harmful / noxious dusts represents

a risk to the health of the person operating the

device and to anyone near the work area.

■ When working on metal for longer periods,

connect the tool to a suitable external extrac-

tion system.

■ Ensure that there is adequate ventilation

when working on plastic, paint, varnish etc.

■ Do not soak the materials or the surface you

are about to work on with liquids containing

solvents.

■ DANGER OF INJURY! Wear close-ﬁ tting

clothing and keep long hair inside a hairnet

or suitable headwear.

■ For safety reasons this device must always be

used with the auxiliary handle in place.

■ The adjustable disc guard cover must al-

ways be in place when working with roughing,

grinding or cutting discs. Otherwise there could

be danger of injury.

■ Use the vacuum dust extraction facility if your

work generates high amounts of dust. Use suction

devices particularly approved for the purpose.

■ Use permitted consumables and tools only.

Check that the speed given on the discs is great-

er or equal to the rated speed of the device.

■ Take note of the direction of rotation and

always hold the device in such a way that the

sparks and grinding debris are thrown away

from your body. Otherwise there could be

danger of injury.

■ Make sure that the dimensions of the disc are

suitable for the device and that the disc is of

a type that ﬁ ts properly on to the mounting

ﬂ ange .

Working procedures

NOTE

►

Grinding tools should only be used for the

recommended applications. Otherwise, they

can break, be damaged or cause injuries.

Rough grinding:

Never use cutting discs for rough

grinding!

■ Move the angle grinder with moderate pres-

sure back and forth over the workpiece.

■ For soft material, move the rough grinding

disc at a ﬂ at angle over the workpiece; for

hard material at a slightly steeper angle.

Abrasive cutting:

Never use rough grinding discs for

cutting!

■ Use only tested ﬁ bre-reinforced cutting or

grinding discs that are approved for a circum-

ferential speed of no less than 80 m/s.

IB_102828_PWS125A1_LB4.indb 8 22.08.14 12:03

PWS 125 A1

CAUTION!

The grinder continues running after being turned

oﬀ . Do not try to brake it by applying lateral

counterpressure.

■ Immobilise the workpiece securely. Use clamps/

vices to hold the workpiece ﬁ rmly in place.

This is much safer than simply holding it in your

hand.

■ Always switch oﬀ the appliance before putting

it away and wait for the appliance to come to

a complete standstill.

■ Release the ON/OFF switch immediately in

the event of a power failure or when the plug

is pulled out. Move it into the OFF position.

This prevents an uncontrolled restart.

■ Use the appliance only for dry cutting or

sanding.

■ The additional handle

must be mounted on

the appliance for all work.

■ Materials containing asbestos may NOT be

processed. Asbestos is a known carcinogen.

Tip! This symbol indicates proper

behaviour!

DANGER! GUIDE THE APPLIANCE

THROUGH THE WORKPIECE IN

REVERSE ROTATION.

► In the opposite direction there is a risk of

kickback. The appliance can be pushed out

of the cut.

■ Always switch the appliance on before ap-

plying it to the workpiece. After completing

the task, lift the appliance from the work piece

and then switch it oﬀ .

■ Always hold the appliance ﬁ rmly with two

hands while working. Ensure that your stance

is secure and stable.

■ For an optimum grinding eﬀ ect, move the ap-

pliance evenly at an angle of 15° to 30° (be-

tween grinding disc and workpiece) backwards

and forwards.

■ When working on angled surfaces, do not

exert great force on the workpiece. If the

rotational speed drops signiﬁ cantly, you must

reduce the pressure exerted to allow safe and

eﬀ ective working. If the appliance suddenly

brakes completely or jams, it must be switched

oﬀ immediately.

■ Cutting: Work with a moderate feed and do

not tilt the cutting disc.

■ Roughing and cutting discs become very

hot – let them cool down completely before

touching them.

■ Never use the appliance for purposes other

than the ones for which it was designed.

■ Always make sure that the appliance is

turned oﬀ before plugging it into the wall

socket.

■ In case of danger, remove the plug from the

socket immediately. Ensure that the appliance

and the power socket are easily and quickly

accessible in the event of an emergency.

■ Always remove the plug from the power

socket during work breaks, when adjusting

the appliance and when it is no longer in use.

The appliance must always be kept clean, dry

and free from oil or grease.

■ Remain alert at all times! Always pay attention

to what you are doing and act with common

sense. Never use the appliance when you are

distracted or don’t feel well.

Operation

Adjusting the blade guard

WARNING – RISK OF INJURY!

► Always remove the plug from the power socket

before working on the appliance. To adjust

the blade guard , you do not need to re-

move the screws

but simply loosen them.

IB_102828_PWS125A1_LB4.indb 9 22.08.14 12:03

PWS 125 A1

RISK OF INJURY!

► Always use the angle grinder with the blade

guard

. The blade guard should be installed

securely. Set it so that the highest possible

degree of safety is achieved, i.e. the smallest

possible part of the grinding disc is exposed

to the operator (see Figs. C, D). The blade

guard

is designed to protect the operator

from fragments and accidental contact with

the grinding tool. The blade guard has 5 stop

positions.

► Turn the blade guard

to the required position

(working position).

The closed side of the blade guard

must

always be toward the operator.

Using the additional handle

CAUTION!

► For safety reasons this appliance may only

be used with the additional handle

The additional handle

can be screwed on

the left or the right depending on the work

method.

Switching on and oﬀ

Check the accessory tool before use. It must be

properly installed, may not be damaged or damp,

should have no cracks and turn freely. Carry out

a 60 second test run. Do not use non-circular or

vibrating tools. Be aware of unusual noises and

sparks. Check whether all the fastening elements

are correctly installed.

Switching on:

♦ Press the safety lock-out .

♦ Press the ON/OFF switch

Switching oﬀ :

♦ Let go of the ON/OFF switch

Setting the rotational speed

♦ Select the desired speed as needed. Turn the

rotational speed preselector adjusting wheel

to the required setting. The required rotational

speed depends on the material being processed

and can be determined through practical tests.

The following table lists suggested settings for

the most common applications. Not all of the

accessories described are included in the

delivery.

Rotation speed preselection:

Material Use Tool Ad-

justing

wheel

Plastic,

lacquer

Polishing Lamb's

wool hood

Finishing Felt polish-

ing disc

Metal Finishing Buﬃ ng

wheel

Paint

removal

Sanding

disc

2–3

Wood,

Metal

Brushes,

Rust removal

Cup brush,

Sanding

disc

Metal Grinding Grinding

disc

4–6

Metal Roughing Roughing

disc

Metal Cutting Cutting

disc

Changing grinding tools

Always wear protective gloves when

changing cutting/rough grinding discs.

♦ Press the spindle locking button

only when

the mounting spindle

is at a complete stand-

still (see Fig. A).

♦ Press the spindle locking button

to lock the

mechanism.

♦ Undo the tensioning nut

using the spanner

(see Fig B).

IB_102828_PWS125A1_LB4.indb 10 22.08.14 12:03

PWS 125 A1

♦ Place the rough grinding or cutting disc on the

mounting ﬂ ange with the label side towards

the appliance.

♦ Then replace the tensioning nut

on the mount-

ing spindle

with the raised side facing up.

♦ Press the spindle locking button

to lock the

mechanism.

♦ Tighten the tensioning nut

using the span-

ner

NOTE

►

If the disc does not turn smoothly or vibrates

after the change, the disc must immediately

be replaced.

♦ For safety’s sake, run at high idle for 60

seconds after every disc change. Be aware of

unusual noises and sparks.

♦ Check whether all the fastening elements are

correctly ﬁ tted.

♦ Make sure that the arrow showing the direction

of rotation (if any) on the cutting or rough grind-

ing discs (including diamond cutting discs) and

the direction of rotation of the appliance (arrow

showing the direction of rotation on the head)

match.

General information about the

supplied grinding tool

■ Grinding tools are very fragile. Extreme care is

required when handling grinding tools.

■ Check grinding tools and brushes for damage

prior to initial use. Do not use damaged, incor-

rectly clamped or incorrecty installed grinding

tools.

■ Follow the safety instructions on the grinding

tools as well as the restrictions on use or safety

instructions.

Storage and handling

■ Grinding tools are to be treated with care and

transported carefully.

■ Grinding tools should be stored in such a way

that they are not exposed to mechanical da-

mage or environmental inﬂ uences (e.g. moisture).

Before using the grinder

■ You should subject grinding tools to a visual

inspection before each use.

■ Do not use grinding tools if they are damaged

or if the expiration date has elapsed.

Using accessories

Cutting/rough grinding discs

You can use the following cutting/rough grinding

discs on this appliance:

Dimensions: ø 125 x 22.2mm to

max. 6mm thick (oﬀ set)

Rotational speed: min. 12000 rpm

Circumferential speed: 80 m/sec

Flap buﬀ er discs for metal

Dimensions: ø 125mm

Rotational speed: min. 12000 rpm

Additional accessories

You can also use the grinding tools below with the

following technical data:

Spindle thread: M14

Rotational speed: min. 12000 rpm

Support plate for

sanding sheets with

dimensions: ø 115mm/125mm

IB_102828_PWS125A1_LB4.indb 11 22.08.14 12:03

PWS 125 A1

Sanding sheets for sanding

wood/rock with dimensions: ø 115mm/125mm

NOTE

►

Can only be used in conjunction with the

support plate!

Cup brushes, wavy wire

with dimensions: ø 75–100mm

Rotational speed: min. 12000 rpm

Cup brushes, knotted wire

with dimensions: ø 75

Rotational speed: min. 12000 rpm

Disc brushes, knotted wire

with dimensions: ø 115 mm

Rotational speed: min. 12000 rpm

Maintenance and cleaning

WARNING! RISK OF INJURY! Switch

the appliance oﬀ and remove the

power plug before starting any work.

■ Do not use any sharp objects to clean the

appliance. Never permit ﬂ uids to penetrate

inside the appliance. The appliance could be

damaged. The carbon brushes should only be

replaced by the service centre or an authorized

specialist workshop. Apart from this, the appli-

ance is maintenance-free.

■ Clean the appliance regularly, preferably im-

mediately after completion of the work.

■ Clean the housing with a dry cloth – do NOT

use petrol, solvents or cleaners that can attack

the plastic.

■ A vacuum cleaner is required for thorough

cleaning of the appliance.

■ Ventilation openings must never be obstructed.

■ Remove any adhering swarf with a brush.

NOTE

►

Unlisted replacement parts (such as carbon

brushes, switch) can be ordered via our

service hotline.

Disposal

The packaging consists of environmentally

friendly material. It can be disposed of in

the local recycling containers.

Do not dispose of power tools in

your normal domestic waste!

European Directive 2012/19/EU requires that

worn-out power tools be collected separately and

fed into an environmentally compatible recycling

process.

Your local community or municipal authorities can

provide information on how to dispose of the worn-

out appliance.

IB_102828_PWS125A1_LB4.indb 12 22.08.14 12:03

PWS 125 A1

Warranty

You are provided a 3-year warranty on this

appliance, valid from the date of purchase.

This appliance has been manufactured with

care and inspected meticulously prior to

delivery. Please retain your receipt as proof

of purchase. In the event of a warranty claim,

please contact your customer service depart-

ment by telephone. This is the only way to

guarantee free return of your goods.

The warranty only covers claims for material and

manufacturing defects, not for damage sustained

during transport, components subject to wear and

tear or damage to fragile components such as

switches or batteries. This appliance is intended

solely for private use and not for commercial pur-

poses. The warranty shall be deemed void in

the case of misuse or improper handling, use of

force and interventions which have not been carried

out by one of our authorised service centres. Your

statutory rights are not restricted by this warranty.

The warranty period is not extended due to repairs

eﬀ ected under the warranty. This also applies to

replaced and repaired components. Any damage

and defects present at the time of purchase must be

reported immediately after unpacking, but no later

than two days after the date of purchase. Repairs

eﬀ ected after expiry of the warranty period shall

be subject to charge.

Service

Service Great Britain

Tel.: 0871 5000 720 (£ 0.10/Min.)

E-Mail: [email protected]

IAN 102828

Hotline availability:

Monday to Friday 08:00 - 20:00 (CET)

Importer

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

GERMANY

www.kompernass.com

Translation of the original

Conformity Declaration

We, KOMPERNASS HANDELS GMBH, Custodian

of Documents: Mr. Semi Uguzlu, BURGSTR. 21,

44867 BOCHUM, GERMANY, hereby declare

that this product complies with the following

standards, normative documents and the EC

directives:

Machinery Directive

(2006 / 42 / EC)

EU Low Voltage Regulations

(2006 / 95 / EC)

EMC (Electromagnetic Compatibility)

(2004 / 108 / EC)

RoHS Directive

(2011 / 65 / EU)

Applied harmonised standards:

EN 60745-1/A11:2010

EN 60745-2-3:2011

EN 55014-1/A2:2011

EN 55014-2/A2:2008

EN 61000-3-2/A2:2009

EN 61000-3-3:2013

Type designation of machine:

Angle grinder PWS 125 A1

Year of manufacture: 06 - 2014

Serial number: IAN 102828

Bochum, 27/06/2014

Semi Uguzlu

- Quality Manager -

Subject to technical changes in the course of

further developments.

IB_102828_PWS125A1_LB4.indb 13 22.08.14 12:03

PWS 125 A1

IB_102828_PWS125A1_LB4.indb 14 22.08.14 12:03

PWS 125 A1

Spis treści

Wstęp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Użytkowanie zgodne z przeznaczeniem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Wyposażenie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Zakres dostawy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Dane techniczne . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Ogólne uwagi na temat bezpieczeństwa elektronarzędzi . . . . . . . . . . . . . . . 17

1. Bezpieczeństwo na stanowisku pracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2. Bezpieczeństwo elektryczne . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3. Bezpieczeństwo osób . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

4. Zastosowanie i obsługa elektronarzędzia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

5. Serwis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Wskazówki bezpieczeństwa do wszystkich zastosowań . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Odbicie i odpowiednie wskazówki bezpieczeństwa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Szczególne wskazówki bezpieczeństwa do szlifowania i cięcia . . . . . . . . . . . . . . . . . . . . . . . 21

Dalsze szczególne wskazówki bezpieczeństwa dotyczące cięcia . . . . . . . . . . . . . . . . . . . . . 21

Szczególne wskazówki bezpieczeństwa podczas szlifowania papierem ściernym . . . . . . . . . 22

Szczególne wskazówki bezpieczeństwa podczas polerowania . . . . . . . . . . . . . . . . . . . . . . . 22

Specjalne wskazówki bezpieczeństwa do pracy ze szczotkami drucianymi . . . . . . . . . . . . . . 22

Specyﬁ czne dla urządzenia wskazówki bezpieczeństwa podczas pracy ze szliﬁ erką kątową . . . . . . 22

Wskazówki dotyczące pracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Obsługa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Przestawianie osłony . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Stosowanie dodatkowego uchwytu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Włączanie i wyłączanie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Regulowanie prędkości obrotowej . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Wymiana narzędzi szliﬁ erskich . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Ogólne informacje na temat dołączonych narzędzi do szlifowania . . . . . . . . . . . . . . . . . . . . 26

Składowanie i obchodzenie się . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Przed uruchomieniem narzędzia szliﬁ erskiego . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Stosowanie osprzętu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Tarcze do zdzierania / cięcia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Tarcze szliﬁ erskie listkowe do metalu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Inny osprzęt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Konserwacja i czyszczenie. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Utylizacja . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Gwarancja . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Serwis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Importer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Tłumaczenie oryginalnej deklaracji zgodności . . . . . . . . . . . . . . . . . . . . . . . . 29

IB_102828_PWS125A1_LB4.indb 15 22.08.14 12:03

PWS 125 A1

SZLIFIERKA KĄTOWA

PWS 125 A1

Wstęp

Gratulujemy zakupu nowego urządzenia.

Wybrany produkt charakteryzuje się wy-

soką jakością. Instrukcja obsługi stanowi

część niniejszego produktu. Zawiera ona

ważne informacje na temat bezpieczeń-

stwa, użytkowania i utylizacji. Przed rozpoczęciem

użytkowania produktu należy zapoznać się ze

wszystkimi informacjami dotyczącymi obsługi i

bezpieczeństwa. Produkt należy użytkować wy-

łącznie zgodnie z zamieszczonym tu opisem oraz

w podanym zakresie zastosowań. W przypadku

przekazania urządzenia osobie trzeciej należy

dołączyć również całą dokumentację.

Użytkowanie zgodne z przeznacze-

niem

Urządzenie jest przeznaczone do cięcia, zdzierania

i szczotkowania materiałów metalicznych bez

użycia wody. Jakiekolwiek inne użycie lub zmiany

urządzenia uważane są za niezgodne z prze-

znaczeniem i kryją w sobie poważne niebezpie-

czeństwo wypadku. Za szkody powstałe wskutek

używania niezgodnego z przeznaczeniem nie

ponosimy odpowiedzialności. Urządzenie nie

nadaje się do zastosowań przemysłowych.

WSKAZÓWKA

►

Szczeliny w ścianach nośnych podlegają

normie DIN 1053 część 1 lub przepisom

właściwym dla danego kraju. Należy bez-

względnie przestrzegać tych przepisów.

Przed rozpoczęciem pracy należy zasięgnąć

rady odpowiedzialnego statyka, architekta

lub odpowiedniego kierownika budowy.

Wyposażenie

Blokada włączenia

Włącznik/wyłącznik

Pokrywa szczotek węglowych

Dodatkowa rękojeść

Przestawna osłona

Nakrętka mocująca

Wrzeciono mocujące

Kołnierz mocujący

Tarcza do cięcia metalu

Przycisk blokady wrzeciona

Pokrętło regulacji obrotów

Klucz do mocowania (rys. B)

Śruby

Zakres dostawy

1 Szliﬁ erka kątowa PWS 125 A1

1 Tarcza do cięcia metalu

1 Dodatkowa rękojeść

1 Osłona

1 Klucz do mocowania

1 Instrukcja obsługi

Dane techniczne

Moc znamionowa: 1200 W

Napięcie znamionowe: 230 - 240 V ∼ 50 Hz

Znamionowa prędkość

obrotowa: n 12000 min

-1

Bezstopniowo regulowana

prędkość obrotowa: 3000 - 12000 min

-1

Gwint wrzeciona: M14

Klasa ochrony: II /

Informacje dotyczące poziomu hałasu i drgań:

Wartość pomiarowa hałasu ustalona zgodnie

z normą EN 60745. Oceniany poziom hałasu

elektronarzędzia wynosi z reguły:

Poziom ciśnienia

akustycznego: L

= 91 dB (A)

Niepewność: K = 3 dB (A)

Poziom mocy

akustycznej: L

= 102 dB (A)

Niepewność: K = 3 dB (A)

Wartości drgań:

Szlifowanie kątowe

(uchwyt główny) a

h, AG

= 13,431 m/s

Szlifowanie kątowe

(uchwyt dodatkowy) a

h, AG

= 9,770 m/s

Niepewność: K = 1,5 m/s

Należy nosić ochronniki słuchu!

IB_102828_PWS125A1_LB4.indb 16 22.08.14 12:03

PWS 125 A1

WSKAZÓWKA

►

Poziom drgań wskazany w tych instruk-

cjach został zmierzony zgodnie z metodą

pomiarową, określoną w normie EN 60745 i

może być użyty do porównywania urządzeń.

Podana wartość emisji drgań może posłużyć

także do wstępnej oceny stopnia narażenia.

OSTRZEŻENIE!

► Poziom drgań będzie zmieniał się w zależności

od rodzaju zastosowania elektronarzędzia i

w niektórych przypadkach może przekraczać

wartość wskazaną w niniejszych instrukcjach.

Narażenie na drgania mogłoby zostać nie-

prawidłowo ocenione, gdyby narzędzie było

regularnie wykorzystywane w taki sposób.

W celu dokładnej oceny stopnia narażenia

na drgania w określonym okresie pracy na-

leży również uwzględniać czasy, w których

urządzenie pozostawało wyłączone lub było

wprawdzie włączone, jednak nie było fak-

tycznie wykorzystywane. Może to znacznie

obniżyć stopień narażenia na drgania w

całym okresie pracy.

Objaśnienia do naklejek informacyjnych,

znajdujących się na urządzeniu!

Przed uruchomieniem prze-

czytać instrukcję obsługi i

wskazówki bezpieczeństwa!

Nosić ochronniki słuchu!

Nosić okulary ochronne!

Nosić zamknięte obuwie!

Nosić rękawice ochronne!

Nosić maskę przeciwpyłową!

Urządzenie nie nadaje się do

szlifowania na mokro

Urządzenie nie nadaje się do

szlifowania bocznego

Używanie uszkodzonych tarcz

do cięcia lub zdzierania jest

niebezpieczne i może spowo-

dować poważne obrażenia!

Ogólne uwagi na

temat bezpieczeństwa

elektronarzędzi

OSTRZEŻENIE!

► Przeczytaj wszystkie wskazówki bezpieczeń-

stwa oraz instrukcje. Nieprzestrzeganie po-

niższych wskazówek bezpieczeństwa oraz

instrukcji może być przyczyną porażenia

prądem elektrycznym, pożaru i/lub ciężkich

obrażeń ciała.

Wszystkie wskazówki bezpieczeństwa oraz

instrukcje należy zachować do późniejszego

wykorzystania.

Użyte w wskazówkach bezpieczeństwa pojęcie

„elektronarzędzie“ dotyczy narzędzi elektrycznych

zasilanych sieciowo (przez kabel sieciowy) oraz

narzędzi elektrycznych zasilanych akumulatorami

(bez kabla sieciowego).

1. Bezpieczeństwo na stanowisku

pracy

a) Stanowisko pracy utrzymuj zawsze w czy-

stości oraz dbaj o dobre oświetlenie. Nie-

porządek i niedostateczne oświetlenie mogą

doprowadzić do różnych wypadków.

b) Nigdy nie używaj elektronarzędzia w miej-

scach zagrożonych wybuchem, w których

znajdują się łatwopalne ciecze, gazy lub

pyły. Elektronarzędzia wytwarzają iskry, które

mogą spowodować zapłon pyłu lub oparów.

c) W czasie użytkowania elektronarzędzia do-

pilnuj, aby w pobliżu nie przebywały dzieci

ani żadne inne osoby. W przypadku odwróce-

nia uwagi od pracy możesz stracić kontrolę nad

urządzeniem.

IB_102828_PWS125A1_LB4.indb 17 22.08.14 12:03

Stránka sa načítava ...

Parkside PWS 125 A1 ANGLE GRINDER Translation Of Original Operation Manual

Značka: Parkside

Model: PWS 125 A1 ANGLE GRINDER

Kategória: Elektrické náradie

Typ: Translation Of Original Operation Manual

Stiahnite si PDF

správa

V iných jazykoch

polski: Parkside PWS 125 A1 ANGLE GRINDER

Parkside PWS 125 A1 ANGLE GRINDER Translation Of Original Operation Manual

Parkside PWS 125 A1 ANGLE GRINDER Translation Of Original Operation Manual

V iných jazykoch

Súvisiace články

Ďalšie dokumenty