Parkside 331996 1907 Operation and Safety Notes

IAN 331996_1907

INVERTER WELDER

INVERTNÁ ZVÁRAČKA

INVERTERSKI VARILNI APARAT

INVERTER-SCHWEISSGERÄT

INVERTNÍ SVÁREČKA

INVERTERES HEGESZTŐKÉSZÜLÉK

Operation and Safety Notes

Translation of the original instructions

Návod na obsluhu a bezpečnostné upozornenia

Originálny návod na obsluhu

Navodila za upravljanje in varnostna opozorila

Prevod originalnega navodila za uporabo

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung

Návod k obsluze a bezpečnostní pokyny

Originální návod k obsluze

Kezelési és biztonsági hivatkozások

Az eredeti használati utasítás fordítása

GB

SK

SI

DE

CZ

HU

AT

CH

INVERTER WELDER PISG 120 A2

SK

SI

CZ

HU

331996_Inverter_Schweissgeraet_PISG_120_A2_cover_LB4.indd 3 05.12.19 15:44

GB

Before reading, unfold the page containing the illustrations and familiarise yourself with all

functions of the device.

HU

Olvasás előtt hajtsa ki az ábrát tartalmazó oldalt, és ezután ismerje meg a készülék

mindegyik funkcióját.

SI

Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.

CZ

Než začnete číst tento návod k obsluze, rozložte stránku s obrázky a seznamte se se všemi

funkcemi zařízení.

SK

Prv než začnete čítať tento návod, rozložte si stranu s obrázkami a potom sa oboznámte so

všetkými funkciami zariadenia.

DE AT CH

Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich

anschließend mit allen Funktionen des Gerätes vertraut.

GB Operation and Safety Notes Page 5

HU Kezelési és biztonsági hivatkozások Oldal 23

SI Navodila za upravljanje in varnostna opozorila Stran 43

CZ Návod k obsluze a bezpečnostní pokyny Strana 61

SK Návod na obsluhu a bezpečnostné upozornenia Strana 79

DE / AT / CH Montage-, Bedienungs- und Sicherheitshinweise Seite 97

331996_Inverter_Schweissgeraet_PISG_120_A2_cover_LB4.indd 4 05.12.19 15:44

A

C1

C3

C2

C4

B

–

(schwarz)

+

(rot)

1

4

10

9

5

8 7

7

11

1 2

2

3

331996_Inverter_Schweissgeraet_PISG_120_A2_cover_LB4.indd 5 05.12.19 15:44

6 7 11

8

331996_Inverter_Schweissgeraet_PISG_120_A2_cover_LB4.indd 8 05.12.19 15:44

5GB

Table of contents

List of pictograms used .........................................................................Page 6

Introduction ..............................................................................................Page 7

Intended use ................................................................................................ Page 7

Package contents .........................................................................................Page 7

Parts description ..........................................................................................Page 7

Technical speciﬁcations .................................................................................Page 7

Safety instructions ..................................................................................Page 8

Potential hazards during electric arc welding ................................................... Page 10

Welding mask-speciﬁc safety instructions .........................................................Page 12

Environment with increased electrical hazard...................................................Page 13

Welding in tight spaces ................................................................................Page 14

Total of open circuit voltages .........................................................................Page 14

Using shoulder straps ...................................................................................Page 14

Protective clothing ........................................................................................Page 15

EMC Device Classiﬁcation ............................................................................Page 15

Before use .................................................................................................Page 16

Fit welding mask ....................................................................................Page 16

Using the device ...................................................................................... Page 16

Welding .....................................................................................................Page 18

Maintenance and cleaning ................................................................... Page 18

Information about recycling and disposal ....................................... Page 19

EU Declaration of Conformity ..............................................................Page 19

Warranty and service information ....................................................Page 20

Warranty conditions ..................................................................................... Page 20

Warranty period and statutory claims for defects .............................................Page 20

Extent of warranty ........................................................................................Page 20

Processing of warranty claims ........................................................................Page 21

Service .......................................................................................................Page 21

331996_Inverter_Schweissgeraet_PISG_120_A2_content_LB4.indb 5 05.12.19 15:41

6 GB

List of pictograms used

Caution! Read the operat-

ing instructions!

Risk of serious injury

or death.

1~50 Hz

Power input;

Number of phases and

Alternating current symbol

and rated value of the

frequency.

Caution!

Risk of electric shock!

Important note!

Do not dispose of any

electrical devices in

domestic waste!

Dispose of packaging properly.

Do not dispose of the appliance

in household waste!

Never use the device in the

open or when it’s raining!

Manual arc welding with

encased rod electrodes.

Electric shock from the

welding electrode can be

fatal!

IP21S Protection class.

Inhalation of welding fumes

can endanger your health.

Suitable for welding under

increased electrical hazard.

Welding sparks can cause

an explosion or ﬁre.

Single-phase static frequency

converter-transformer-

commutator.

Arc beams can damage

your eyes and injure your

skin.

H Insulation class.

Electromagnetic ﬁelds

can disrupt the function

of cardiac pacemakers.

Direct current.

Warning: Potential hazards!

Made from recycling material.

X % Duty cycle. U

0

Rated value of the open circuit

voltage

I

1 max

Greatest rated value

of the mains current

U

1

Rated value of the mains

voltage

I

2 max

Greatest rated value

of the welding current

U

2

Standardised operating

voltage

I

1 eff

Effective value of the

greatest mains current

331996_Inverter_Schweissgeraet_PISG_120_A2_content_LB4.indb 6 05.12.19 15:41

7GB

INVERTER WELDER

PISG 120 A2

 Introduction

Congratulations!

You have purchased

one of our high-quality

products. Please familiarise yourself with

the product before setup or ﬁrst use.

Please also read the safety instructions

carefully. This product must be set up or

used only by people who have been

trained to do so.

KEEP OUT OF THE REACH OF

CHILDREN!

 Intended use

This welding device is ideal for welding

metals such as carbon steel, steel alloy,

other stainless steel, copper, aluminium,

titanium, etc. The product has a control

lamp, a heat protection display and a

cooling fan. In addition, it is ﬁtted with

a carrying strap so that the product

can be lifted and moved safely. If it is

not handled properly the product can

be dangerous for individuals, animals

and property. Use the product only

as described and only for the speciﬁc

applications as stated. Keep these

instructions in a safe place. Ensure you

hand over all documentation when

passing the product on to anyone else.

Any use that differs to the intended

use as stated above is prohibited and

potentially dangerous. Damage or

injury caused by misuse or disregarding

the above warning is not covered by

the warranty or any liability on the part

of the manufacturer. The device is not

intended for commercial use.

Commercial use will void the guarantee.

 Package contents

1 Inverter welder

1 Welding mask

2 Welding cables

1 Combi wire brush

with slag hammer

1 Carrying strap

5 Welding electrodes (2 x 1.6 mm;

2 x 2.0 mm; 1 x 2.5 mm)

1 Operating instructions

1 Extension cable 2 m

 Parts description

1

Carrying strap

2

Control lamp for overheating

3

Rotary knob

4

Earth terminal

5

Electrode holder

6

Combi wire brush with slag hammer

7

Welding mask

8

Handle

9

ON/OFF switch

10

Power cable 2 m

11

Protective glass

 Technical speciﬁcations

Mains connection: 230 V~ 50 Hz

Nominal power input: 3.7 kW

Max. welding current

and the appropriate

standardised operating

voltage:

10 A/20.4 V -

120 A/24.8 V

Rated value of the

mains voltage:

U

1

:230V

Greatest rated value

of the mains current:

I

1max

: 25.2 A

Introduction

331996_Inverter_Schweissgeraet_PISG_120_A2_content_LB4.indb 7 05.12.19 15:41

8 GB

Maximum effective

input current:

I

1eff

: 13.8 A

Rated value of the

open circuit voltage:

U

0

: 70 V

Protection class: IP21S

Weight: approx. 3 kg

Duty cycle X: 30% at 40 °C

Falling characteristic

Material thicknesses

which can be welded:

1.5 mm -

3.0 mm

 Safety instructions

Please read the operating instruc-

tions with care and observe the

notes described. Familiarise

yourself with the device, its

proper use and the safety notes

based on these operating instruc-

tions. The rating plate contains

all technical data of this welding

device; please learn about the

technical features of this device.

 Keep the

packaging material away from

small children. There is a risk

of suffocation!

 This device may be used by

children aged 16 years and

older, and by persons with

reduced physical, sensory or

mental capacities, or a lack of

experience and knowledge,

if they are supervised or have

been instructed in how to use

the device safely and under-

stand the dangers that may

arise when using it. Do not

allow children to play with the

device. Cleaning and day-to-

day maintenance must not be

performed by children without

supervision.

 Repairs or/and maintenance

work must only be carried out

by qualiﬁed electricians.

 Only use the welding cables

(PISG 120 A2, H01N2-

D1x10mm

2

) included in the

scope of delivery.

 During operation, the device

should not be positioned

directly on the wall, covered or

jammed between other devices

so that sufﬁcient air can be

absorbed through the ventila-

tion slats. Makes sure that the

device is correctly connected

to the supply voltage. Avoid

any form of tensile stress of

the power cable. Disconnect

the plug from the socket prior

to setting up the device in

another location.

 If the device is not in operation,

always switch it off by pressing

the ON/OFF switch. Place the

electrode holder on an insu-

lated surface and only remove

it from the holder after allowing

it to cool down for 15 minutes.

Introduction / Safety instructions

331996_Inverter_Schweissgeraet_PISG_120_A2_content_LB4.indb 8 05.12.19 15:41

9GB

 Pay attention to the condition

of the welding cable, electrode

holder and the earth terminal.

Wear and tear of the insulation

and the live parts can lead to

hazards and reduce the quality

of the welding work.

 Arc welding creates sparks,

molten metal parts and

smoke. Therefore ensure that:

All ﬂammable substances and/

or materials are removed from

the work station and its imme-

diate surrounding.

 Ensure the work station is

ventilated.

 Do not weld on containers,

vessels or tubes that contain

or contained ﬂammable liquids

or gases.

 Avoid any

form of direct contact with the

welding current circuit. The

open circuit voltage between

the electrode holder and earth

terminal can be dangerous,

there is a risk of electric shock.

 Do not store or use the device

in a damp or wet environment

or in the rain. Protection rating

IP21S is applicable in this case.

 Protect your eyes using the

appropriate protective glasses

(DIN level 9-10), which are

fastened to the supplied weld-

ing mask. Wear gloves and

dry protective clothing that are

free of oil and grease to pro-

tect the skin from exposure to

ultraviolet radiation of the arc.

 Do not use

the welding power source to

defrost pipes.

Please note:

 The light radiation emitted by

the electric arc can damage

eyes and cause burns to

the skin.

 Arc welding creates sparks

and drops of melted metal.

The welded workpiece starts

to glow and remains hot

for a relatively long period.

Therefore, do not touch the

workpiece with bare hands.

 Arc welding can cause

vapours to be release that

may be hazardous to health.

Be careful not to inhale these

vapours.

 Protect yourself from the

harmful effects of the electric

arc and keep people that are

not involved in the work away

from the arc maintaining a

distance of at least 2 m.

ATTENTION!

 During the operation of the

welding device, other consum-

ers may experience problems

Safety instructions

331996_Inverter_Schweissgeraet_PISG_120_A2_content_LB4.indb 9 05.12.19 15:41

10 GB

with the voltage supply

depending on the network

conditions at the connection

point. In case of doubt, please

contact your energy supply

company.

 During the operation of the

welding device, other devices

may malfunction, e.g. hearing

aids, cardiac pacemakers, etc.

 Potential hazards during

electric arc welding

There are a series of potential

hazards that can occur during

electric arc welding. It is there-

fore particularly important for the

welder to observe the following

rules to avoid endangering him/

herself and others and to prevent

damage to people and the

device.

 Work on the voltage side,

e.g. on cables, plugs, sockets

etc., may only be carried

out by qualiﬁed electricians

according to national and

local regulations.

 In the event of accidents,

disconnect the welding

device from the mains voltage

immediately.

 If electrical contact voltages

occur, switch off the device

immediately and have it

checked by a qualiﬁed

electrician.

 Always ensure good electrical

contacts on the welding

current side.

 Always wear insulating gloves

on both hands during welding

work. These provide protection

from electrical shocks (no-load

voltage of the welding current

circuit), harmful radiations

(heat and UV radiation)

and incandescent metal and

splashes of slag.

 Wear sturdy, insulating shoes.

The shoes should also insulate

when exposed to moisture.

Loafers are not suitable as

falling incandescent metal

droplets can cause burns.

 Wear suitable protective cloth-

ing, no synthetic garments.

 Do not look into the electric

arc without eye protection;

only use a welding mask with

the prescribed protective glass

as per DIN. In addition to light

and heat radiation, which

can dazzle or cause burns,

the electric arc also emits UV

radiation. Without suitable

protection the invisible ultravi-

olet radiation can cause very

painful conjunctivitis which

is not apparent until several

hours later. Furthermore, UV

Safety instructions

331996_Inverter_Schweissgeraet_PISG_120_A2_content_LB4.indb 10 05.12.19 15:41

11GB

radiation can cause burns with

sunburn-like effects on unpro-

tected parts of the body.

 Any persons in the vicinity

of the electric arc or helpers

must also be informed of the

dangers and be equipped

with the necessary protective

equipment. If necessary, set up

protective walls.

 Ensure an adequate supply

of fresh air whilst welding,

particularly in small spaces,

as it produces smoke and

harmful gases.

 No welding work may be

carried out on containers that

have been used for storing

gases, fuels, mineral oils or

similar – even if they have

been empty for a long time

– as possible residues may

present a risk of explosion.

 Special regulations apply in

rooms where there is a risk of

ﬁre or explosion.

 Welded joints that are subject

to heavy stress loads and are

required to comply with certain

safety requirements may only

be carried out by specially

trained and certiﬁed welders.

Examples of this are pressure

vessels, running rails, tow

bars, etc.

ATTENTION! Always connect

the earth terminal as close as

possible to the point of weld to

provide the shortest possible path

for the welding current from the

electrode to the earth terminal.

Never connect the earth terminal

to the housing of the welding

device! Never connect the earth

terminal to earthed parts far

away from the workpiece, e.g. a

water pipe in another corner of

the room. This could otherwise

damage the protective bonding

system of the room you are

welding.

 Do not use the welding device

in the rain.

 Do not use the welding device

in a moist environment.

 Only place the welding device

on a level surface.

 The output is rated at an

ambient temperature of 20°C.

The welding time can be

reduced at higher temperatures.

Risk of electric shock:

Electric shock from the

welding electrode can be

fatal. Do not weld in rain or

snow. Wear dry insulating

gloves. Do not touch the elec-

trodes with bare hands. Do not

wear wet or damaged gloves.

Safety instructions

331996_Inverter_Schweissgeraet_PISG_120_A2_content_LB4.indb 11 05.12.19 15:41

12 GB

Protect yourself from electric

shock with insulation against

the workpiece. Do not open

the device housing.

Danger from welding

fumes:

 Inhalation of welding fumes

can endanger health.

Do not keep your head in the

fumes. Use the equipment in

open areas. Use extractors

to remove the fumes.

Danger from welding

sparks:

 Welding sparks can cause

an explosion or ﬁre. Keep

ﬂammable substances away

from the welding location.

Do not weld next to ﬂammable

substances. Welding sparks

can cause ﬁres. Keep a ﬁre

extinguisher close by and an

observer should be present to

be able to use it immediately.

Do not weld on drums or any

other closed containers.

Danger from arc beams:

 Arc beams can damage your

eyes and injure your skin.

Wear a hat and safety goggles.

Wear hearing protection and

high, closed shirt collars.

Wear welding safety helmets

and make sure you use the

appropriate ﬁlter settings. Wear

complete body protection.

Danger from electro-

magnetic ﬁelds:

 Welding current generates

electromagnetic ﬁelds.

Do not use if you have a

medical implant. Never wrap

the welding cable around your

body. Guide welding cables

together.

 Welding mask-speciﬁc

safety instructions

 With the help of a bright light

source (e.g. lighter) examine

the proper functioning of the

welding mask prior to starting

with any welding work.

 Weld spatters can damage the

protective screen. Immediately

replace damaged or scratched

protective screens.

 Immediately replace damaged

or highly contaminated or

splattered components.

 The device must only be

operated by people over the

age of 16.

Safety instructions

331996_Inverter_Schweissgeraet_PISG_120_A2_content_LB4.indb 12 05.12.19 15:41

13GB

 Please familiarise yourself

with the welding safety instruc-

tions. Also refer to the safety

instructions of your welding

device.

 Always wear a welding mask

while welding. If it is not

used, you could sustain severe

lesions to the retina.

 Always wear protective cloth-

ing during welding operations.

 Never use the welding mask

without the protective screen.

 Regularly replace the protec-

tive screen to ensure good

visibility and fatigue-proof

work.

 Environment with

increased electrical

hazard

When welding in environments

with increased electrical hazard,

the following safety instructions

must be observed. Environments

with increased electrical hazard

may exist, for example:

 In workplaces where the

space for movement is

restricted, such that the welder

is working in a forced posture

(e.g.: kneeling, sitting, lying)

and is touching electrically

conductive parts;

 In workplaces which are

restricted completely or in

part in terms of electrical

conductivity and where there is

a high risk through avoidable

or accidental touching by the

welder;

 In wet, humid or hot work-

places where the air humidity

or weld signiﬁcantly reduces

the resistance of human skin

and the insulating properties

or effect of protective equip-

ment.

Even a metal conductor or

scaffolding can create an envi-

ronment with increased electrical

hazard.

In this type of environment,

you must use insulated surfaces

and intermediate layers, and in

addition you must wear gauntlet

gloves and

Headwear made of leather or

other insulating materials, in

order to insulate the body from

earth. The welding power source

must be located outside the work-

ing area or electrically conductive

surfaces and out of the welder’s

reach.

Additional protection against a

shock from the mains power in

Safety instructions

331996_Inverter_Schweissgeraet_PISG_120_A2_content_LB4.indb 13 05.12.19 15:41

14 GB

the event a fault can be provided

by using a fault-circuit interrupter,

which is operated with a leakage

current of no more than 30 mA

and covers all mains-powered

devices in close proximity. The

fault-circuit interrupter must be

suitable for all types of current.

There must be means of rapid

electrical isolation of the welding

power source or the welding cir-

cuit (e.g. emergency stop device)

which are easily accessible.

When using welding devices

under electrically dangerous

conditions, the output voltage

of the welding device must be

greater than 113 volt when idling

(peak value). Based on the output

voltage this welding device may

be used in these conditions.

 Welding in tight spaces

When welding in tight spaces

this may pose a hazard through

toxic gases (risk of suffocation).

In tight spaces you may only

weld if there are trained individu-

als in the immediate vicinity who

can intervene if necessary. In this

case, before starting the welding

procedure, an expert must carry

out an assessment in order to

determine what steps are neces-

sary, in order to guarantee safety

at work and which precautionary

measures should be taken during

the actual welding procedure.

 Total of open circuit

voltages

When more than one welding

power source is operated at the

same time, their open circuit

voltages may add up and lead to

an increased electrical hazard.

Welding power sources must

be connected in such a way

that the danger is minimised.

The individual welding power

sources, with their individual con-

trol units and connections, must

be clearly marked, in order to

be able to identify which device

belongs to which welding power

circuit.

 Using shoulder straps

Welding must not take place

if the welding power source is

being carried e.g. with a shoul-

der strap.

This is intended to prevent:

 The risk of losing your balance

if the lines or hoses which are

connected are pulled

Safety instructions

331996_Inverter_Schweissgeraet_PISG_120_A2_content_LB4.indb 14 05.12.19 15:41

15GB

 The increased risk of an elec-

tric shock as the welder comes

into contact with the earth

if he/she is using a Class I

welding power source, the

housing of which is earthed

through its conductor.

 Protective clothing

 At work, the welder must

protect his/her whole body by

using appropriate clothing and

face protection against radia-

tions and burns. The following

steps must be observed:

 Wear protective clothing

prior to welding work

 Wear gloves.

 Open windows or use fans

to guarantee air supply.

 Wear safety goggles and

face mask.

 Gauntlet gloves made of a

suitable material (leather) must

be worn on both hands. They

must be in perfect condition.

 A suitable apron must be

worn to protect clothing from

ﬂying sparks and burns. When

speciﬁc work, e.g. overhead

welding, is required, a protec-

tive suit must be worn and,

if necessary, even head

protection.

Protection against rays

andburns

 Warn of the danger to the

eyes by hanging up a sign

saying “Caution! Do not look

into ﬂames!”. The workplaces

must be shielded so that the

persons in the vicinity are

protected. Unauthorised

persons must be kept away

from welding work.

 The walls in the immediate

vicinity of ﬁxed workplaces

should neither be bright

coloured or shiny. Windows

up to head height must be

protected to prevent rays

from penetrating or reﬂecting

through them, e.g. by using

suitable paint.

 EMC Device Classiﬁcation

As per the standard

IEC 60974-10, this welding

device is a welding device with

class A electromagnetic compat-

ibility. Thus it complies with the

corresponding requirements for

commercial and domestic use. In

residential areas, it can be con-

nected to the public low-voltage

supply network.

Even if the welding device com-

plies with the emission limit values

Safety instructions

331996_Inverter_Schweissgeraet_PISG_120_A2_content_LB4.indb 15 05.12.19 15:41

16 GB

of the standard, arc welding

devices can still result in electro-

magnetic interferences in sensitive

systems and devices.

The operator

is responsible for malfunctions

that occur through the arc while

welding and must take suitable

protective measures. In doing so,

the operator must consider the

following:

– network, control, signal and

telecommunication lines

– computers and other micro-

processor-controlled devices

– TVs, radios and other playback

devices

– electronic and electrical safety

equipment

– people with cardiac pace-

makers or hearing aids

– measurement and calibration

devices

– interference immunity of other

equipment nearby

– the time at which the welding

work is carried out.

The following is recommended

to reduce possible interference

radiation:

– equip the mains connection

with a mains ﬁlter

– the welding device must be

regularly maintained and kept

in a good condition

– welding cables should be

completely uncoiled and run as

close to parallel with the ﬂoor

as possible

– devices and systems that are

compromised by the inter-

ference radiation must be

removed from the welding area

or shielded.

 Before use

Take the device and accessories out

of the packaging and check them for

damage (e.g. transport damage).

 Fix the carrying strap

1

onto the

device (see Fig. C1–C4).

 Connect the electrode holder

5

and

the earth terminal

4

to the welding

device.

 Position an electrode in the clamps

of the electrode holder.

 Fit welding mask

 Fit the handle

8

onto the welding

mask

7

, as shown in Fig. A.

 Fit the protective glass

11

on to the

welding mask

7

, as shown in

Fig.A.

 The protective glass

10

must be

pushed in from the top.

Note: If you are not able to push the

protective glass

10

in fully, gently press

on the outside of the protective glass

10

.

 Using the device

Note: The welding device is designed

for welding with electrodes.

 Use the electrode holder clamps

without protruding bracket screws,

which meet the current safety

standards.

Safety instructions / Before use / Fit welding mask / Using the device

331996_Inverter_Schweissgeraet_PISG_120_A2_content_LB4.indb 16 05.12.19 15:41

17GB

 Make sure that the ON/OFF switch

9

is set to position “O” (“OFF”)

or that the power cable

10

is not

plugged into the socket.

 Connect the welding cable

according to its polarity and in

accordance with the speciﬁcations

of the electrode manufacturer.

 To do this, connect the connector of

the earth terminal

4

(black) with the

relevant output on the inverter welder

(black, marked with “-”).

 Connect the connector of the

electrode holder

5

(red) with the

relevant output on the inverter welder

(red, marked with “+”).

 Put on appropriate protective

clothing in accordance with the

speciﬁcations and prepare your

workspace.

 Connect the earth terminal

4

to the

workpiece.

 Clamp the electrode into the elec-

trode holder

5

.

 Switch the device on by setting the

ON/OFF switch to the

9

“I” (“ON”)

position.

 Adjust the welding current using the

rotary knob

3

depending on the

electrode being used.

Note: See the following table for infor-

mation on the welding current to be used,

depending on the electrode diameter.

Ø Electrode Welding current

1.6 mm 40-55 A

2.0 mm 55-65 A

2.5 mm 65-80 A

3.2 mm 80-120 A

Attention: Do not bring the earth

terminal

4

and the electrode holder

5

/

electrodes into direct contact with one

another.

Attention: When welding with

electrodes (MMA – manual metal arc

welding – electrode welding), the

electrodeholder

5

and the earth

terminal

4

must be connected in

accordance with the speciﬁcations of

the welding wire to plus (+) or minus (-).

 Hold the welding mask

7

in front

of the face and start the welding

procedure.

 To stop the procedure, set the ON/

OFF switch

9

to “O” (“OFF”)

position.

ATTENTION!

When the thermal sensor is triggered,

the yellow control lamp

2

lights up.

In this case, it will not be possible to

continue welding. The device will

remain in operation so that the fan can

cool the device. As soon as the device

is ready for operation again, the yellow

control lamp

2

will switch off automati-

cally. The welding function can now be

used again.

ATTENTION!

Make sure that you do not rub the weld-

ing wire on the workpiece. Doing this

can damage the workpiece and make

it more difﬁcult to ignite the arc. After

the arc is ignited, maintain the correct

gap from the workpiece. The distance

should be appropriate to the diameter

of the welding wire being used. When

welding maintain this gap as accurately

and consistently as possibly. The angle

between the welding wire and the direc-

tion of operation should be between

20° and 30°.

ATTENTION!

The welding clamp and welding wire

must be placed on the insulated bracket

after welding. Wait until the wire is

cooled before removing the welding

slag. To weld an intermittent weld seam

Using the device

331996_Inverter_Schweissgeraet_PISG_120_A2_content_LB4.indb 17 05.12.19 15:41

18 GB

again you must ﬁrst remove the welding

slag at the welding position.

ATTENTION!

A voltage which is 10% below the rated

input voltage of the welding device can

have the following consequences:

 The power to the device will reduce.

 The arc stops or becomes unstable.

ATTENTION!

 The arc radiation can lead to inﬂam-

mation of the eyes and skin burns.

 Casting and welding slag can cause

eye injuries and burns.

 Wear tinted safety goggles or a

protective mask.

 The safety mask must meet the

EN175 safety standards.

 It is essential that you only use the

welding cable which is included with

the delivery (10 mm

2

).

 Welding

Choose between push and drag welding. The following section shows the impact of

the direction of movement on the properties of the weld seam:

Push welding Drag welding

Burn smaller larger

Weld seam width larger smaller

Weld bead ﬂatter higher

Weld seam fault larger smaller

Note: You decide for yourself which

type of welding is most suitable, once

you have welded a sample piece.

Note: Once it has worn down com-

pletely, the electrode must be replaced.

 Maintenance and

cleaning

Note: The welding device must be

regularly serviced and overhauled for

proper function and for compliance with

the safety requirements. Improper and

wrong operation may cause failures and

damage to the device.

 Before performing cleaning work on

the welding tool, disconnect the

power cable

10

from the power

Using the device / Welding / Maintenance and cleaning

331996_Inverter_Schweissgeraet_PISG_120_A2_content_LB4.indb 18 05.12.19 15:41

19GB

outlet to ensure the tool is safely

isolated from the power supply.

 Clean the exterior of the welding

device and its accessories regularly.

Use compressed air, cotton waste or

a brush to remove dirt and dust.

Note: The following kinds of mainte-

nance work must be performed only by

suitably-qualiﬁed personnel.

 The current regulator, earthing

device, internal cables, the coupling

device of the welding torch and

adjusting screws must be serviced

regularly. Re-tighten loose screws

and replace rusty screws (replace-

ment M4x10 screws are available in

any commercial hardware store).

 Check the insulation resistance levels

of the welding device regularly.

To do this use an appropriate

measuring device.

 In case of a defect or a necessary

replacement of equipment parts,

please contact the appropriate

qualiﬁed personnel.

 Information about

recycling and disposal

Don’t throw away – recycle

Please return this device, accesso-

ries and packaging to your local

recycling depot.

According to European Directive

2012/19/EU, used electrical devices

must be collected separately for envi-

ronmentally compatible recycling or

recovery. Please return this device to an

approved waste management company

or use your municipal waste collection

service. Please ensure you comply with

local regulations. If you have any ques-

tions, please contact your local authority

or waste management company.

 EU Declaration of

Conformity

We,

C.M.C. GmbH

Responsible for documentation:

Dr Christian Weyler

Katharina-Loth-Str. 15

66386 St. Ingbert

Germany

hereby take sole responsibility for

declaring that the product

Inverter welder

Art. no.: 2249

Year of manufacture: 2020/18

IAN: 331996_1907

Model: PISG 120 A2

meets the basic safety requirements as

speciﬁed in the European Directives

EC low-voltage directive:

2014/35/EU

EC Guideline on Electromagnetic

Compatibility:

2014/30/EU

RoHS directive:

2011/65/EU+2015/863/EU

and the amendments to these Directives.

The object of the declaration described

above meets the requirements of

Directive 2011/65/EU of the European

Parliament and of the Council of

8June 2011 on the restriction of the

use of certain hazardous substances in

electrical and electronic equipment.

This conformity assessment is based on

the following harmonised standards:

... / Information about recycling and disposal / EU Declaration of Conformity

331996_Inverter_Schweissgeraet_PISG_120_A2_content_LB4.indb 19 05.12.19 15:41

20 GB

EU Declaration of Conformity / Warranty and service information

EN 60974-1:2012

EN 60974-10:2014/A1:2015

St. Ingbert, 01/10/2019

pp Dr Christian Weyler

– Quality Assurance –

 Warranty and service

information

Warranty from Creative

Marketing & Consulting GmbH

Dear Customer,

The warranty for this equipment is

3years from the date of purchase. In the

event of product defects, you have legal

rights against the retailer of this product.

Your statutory rights are not affected in

any way by our warranty conditions,

which are described below.

 Warranty conditions

The warranty period begins on the date

of purchase. Please retain the original

sales receipt. This document is required

as your proof of purchase.

Should this product show any defect

in materials or manufacture within

3years from the date of purchase, we

will repair or replace it – at our dis-

cretion – free of charge. This warranty

service requires that you retain proof of

purchase (sales receipt) for the defective

device for the three year period and that

you brieﬂy explain in writing what the

fault entails and when it occurred.

If the defect is covered by our warranty,

we will repair and return your product

or send you a replacement. The original

warranty period is not extended when a

device is repair or replaced.

 Warranty period and

statutory claims for

defects

The warranty period is not extended

by the guarantee. This also applies to

replaced and repaired parts. Any dam-

ages or defects detected at the time of

purchase must be reported immediately

after unpacking. Any incidental repairs

after the warranty period are subject to

a fee.

 Extent of warranty

This device has been manufactured

according to strict quality guidelines and

carefully inspected before delivery.

The warranty applies to material

and manufacturing defects only. This

warranty does not extend to product

parts, which are subject to normal wear

and tear and can thus be regarded as

consumable parts, or for damages to

fragile parts, e.g. switches, rechargea-

ble batteries or parts made from glass.

This warranty is voided if the product

becomes damaged or is improperly

used or maintained. For proper use

of the product, all of the instructions

given in the operating instructions must

be followed precisely. If the operating

instructions advise you or warn you

against certain uses or actions, these

must be avoided in all circumstances.

331996_Inverter_Schweissgeraet_PISG_120_A2_content_LB4.indb 20 05.12.19 15:41

Stránka sa načítava...

Parkside 331996 1907, PISG 120 A2 Operation and Safety Notes

Súvisiace články

Ostatné dokumenty