Parkside 332010 1907 Operation and Safety Notes

IAN 332010_1907

ARC WELDER

ELEKTRICKÁ SVÁŘEČKA

ELEKTROMOS

HEGESZTŐKÉSZÜLÉK

ELEKTRICKÁ ZVÁRAČKA

ELEKTRO - SCHWEISSGERÄT

Operation and Safety Notes

Translation of the original instructions

Návod k obsluze a bezpečnostní pokyny

Originální návod k obsluze

Kezelési és biztonsági hivatkozások

Az eredeti használati utasítás fordítása

Návod na obsluhu a bezpečnostné upozornenia

Originálny návod na obsluhu

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung

GB

CZ

HU

SK

DE AT CH

ARC WELDER PESG 120 B4

SKCZ

HU

332010_1907_Schweissgeraet_PESG_120_B4_cover_LB4.indd 3 28.11.19 17:16

GB

Before reading, unfold the page containing the illustrations and familiarise yourself with all

functions of the device.

HU

Olvasás előtt hajtsa ki az ábrát tartalmazó oldalt, és ezután ismerje meg a készülék

mindegyik funkcióját.

CZ

Než začnete číst tento návod k obsluze, rozložte stránku s obrázky a seznamte se se všemi

funkcemi zařízení.

SK

Prv než začnete čítať tento návod, rozložte si stranu s obrázkami a potom sa oboznámte so

všetkými funkciami zariadenia.

DE

AT

CH

Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich

anschließend mit allen Funktionen des Gerätes vertraut.

GB Operation and Safety Notes Page 5

HU Kezelési és biztonsági hivatkozások Oldal 23

CZ Návod k obsluze a bezpečnostní pokyny Strana 43

SK Návod na obsluhu a bezpečnostné upozornenia Strana 61

DE / AT / CH Montage-, Bedienungs- und Sicherheitshinweise Seite 79

332010_1907_Schweissgeraet_PESG_120_B4_cover_LB4.indd 4 28.11.19 17:16

A

B

1

7

8

10

87

2

6

5

9

8

3

4

10

7

332010_1907_Schweissgeraet_PESG_120_B4_cover_LB4.indd 5 28.11.19 17:16

Wiring diagram

Kapcsolási rajz

Schéma zapojení

Schéma zapojenia

Schaltplan

332010_1907_Schweissgeraet_PESG_120_B4_cover_LB4.indd 8 28.11.19 17:16

GB 5

Table of contents

List of pictograms used ..................................................................................Page 6

Introduction .........................................................................................................Page 7

Intended use .........................................................................................................Page 7

Package contents .................................................................................................Page 7

Parts description ..................................................................................................Page 8

Technical speciﬁcations ......................................................................................Page 8

Safety instructions ............................................................................................ Page 8

Potential hazards during electric arc welding ................................................. Page 11

Welding mask-speciﬁc safety instructions ........................................................Page 13

Environment with increased electrical hazard ................................................Page 14

Welding in tight spaces ...................................................................................... Page 14

Total of open circuit voltages .............................................................................Page 15

Protective clothing ...............................................................................................Page 15

Protection against rays and burns .....................................................................Page 15

EMC Device Classiﬁcation .................................................................................Page 16

Before use ............................................................................................................Page 16

Mounting ..............................................................................................................Page 17

Fit welding mask ..................................................................................................Page 17

Using the device ................................................................................................Page 17

Welding preparation ..........................................................................................Page 17

Welding ................................................................................................................Page 17

Overload protection ............................................................................................Page 18

Maintenance .......................................................................................................Page 18

Information about recycling and disposal ...........................................Page 18

EU Declaration of Conformity .....................................................................Page 19

Warranty and service information ..........................................................Page 19

Warranty conditions ...........................................................................................Page 19

Warranty period and statutory claims for defects ..........................................Page 20

Extent of warranty ...............................................................................................Page 20

Processing of warranty claims ...........................................................................Page 20

Service ..................................................................................................................Page 21

332010_Schweissgeraet_PESG_120_B4_content_LB4.indb 5 28.11.19 17:13

GB6

List of pictograms used

Caution!

Read the operating

instructions!

Earth terminal connection

1 ~ 50 Hz

Power input;

Number of phases

and

Alternating current

symbol and rated value

of the frequency

Warning:

Potential hazards!

Risk of serious injury

or death.

Do not dispose of any

electrical devices in

domestic waste!

Caution!

Risk of electric shock!

Never use the device

in the open or when

it’s raining!

Important note!

Electric shock from the

welding electrode can

be fatal

138180

Dispose of packaging

properly. Do not

dispose of the appliance

in household waste!

Inhalation of welding

fumes can endanger

your health.

Manual arc welding with

coated rod electrodes

Welding sparks can

cause an explosion or

ﬁ r e .

IP21S Protection type

Arc beams can damage

your eyes and injure

your skin.

Largest rated value

for welding time in

continuous mode Σ

t

ON (max)

Electromagnetic ﬁ elds

can disrupt the function

of cardiac pacemakers.

Largest rated value

for welding time in

intermittent mode Σ

t

ON

332010_Schweissgeraet_PESG_120_B4_content_LB4.indb 6 28.11.19 17:13

GB 7

List of pictograms used / Introduction

Arc welder PESG 120 B4

 Introduction

Congratulations!

You have purchased

one of our high-quality

devices. Please familiarise yourself with

the product before setup or ﬁrst use.

To do so, please read through the

following operating and safety instruc-

tions carefully. This tool must be set up

or used only by people who have been

trained to do so.

KEEP OUT OF THE REACH OF

CHILDREN!

 Intended use

This arc welder is ideal for manual

arc welding of steel, stainless steel,

steel sheet, galvanised metal and cast

material using the appropriate coated

electrodes. If not handled properly, the

product can be dangerous to individu-

als, animals and property.

The welding mask must only be used

with welding protection glasses as well

as header glasses, which are marked as

such and the mask must only be used for

welding.

The welding mask is not suitable for

laser welding! Use the product only

as described and only for the speciﬁc

applications as stated. Keep these

instructions in a safe place. Ensure you

hand over all documentation when

passing the product on to anyone else.

Any use that differs to the intended

use as stated above is prohibited and

potentially dangerous. Damage or

injury caused by misuse or disregarding

the above warning is not covered by

the warranty or any liability on the part

of the manufacturer. The device has

been designed for household use only

and must not be used in commercial or

industrial applications. Commercial use

will void the guarantee.

 Package contents

1 Arc welder

1 Welding mask

2 Welding cables

1 Combi wire brush with slag hammer

1 Assembly and operating instructions

5 Welding electrodes

(2 x 1.6 mm; 2 x 2.0 mm;

1 x 2.5 mm)

Electrode holder

connection

Made from recycled

material

U

0

Rated value of the open

circuit voltage

I

2 max

greatest rated value of the

welding current

U

1

Rated value of the mains

voltage

I

1 max

Greatest rated value of the

mains current

U

2

Standardised operating

voltage

I

1 eff

Effective value of the

greatest mains current

Single-phase transformer

332010_Schweissgeraet_PESG_120_B4_content_LB4.indb 7 28.11.19 17:13

GB8

Introduction / Safety instructions

PLEASE NOTE!

f After unpacking the product,

please check that all of the package

contents are present and that the

devices are in perfect condition.

Do not use the devices if they are

defective.

Keep the packaging materials away

from small children. There is a risk of

suffocation!

 Parts description

Arc welder

1

Handle

2

ON/OFF switch

3

Manual wheel

4

Earth terminal

5

Electrode holder

6

Control lamp for overheating

Welding mask

7

Welding mask

8

Handle

9

Combi wire brush with slag hammer

10

Protective glass

 Technical speciﬁcations

Mains connection: 230 V~ 50 Hz

Max. welding current

and the appropriate

standardised operating

voltage:

75 A /

21 V-100A /

22 V

Rated value of the mains

voltage:

U

1

: 230 V

Greatest rated value of

the mains current:

I

1 max

: 22.5 A

Maximum effective input

current:

I

1eff

: 7A

Rated value of the open

circuit voltage:

U

0

: 48 V

Protection class: IP21S

Material thickness which

can be welded:

1.5 - 3.0 mm

Weight: 12 kg

 Safety instructions

Please read the operating instruc-

tions with care and observe the

notes described. Familiarise

yourself with the device, its proper

use and the safety notes based on

these operating instructions. The

rating plate contains all technical

data of this welding device;

please learn about the technical

features of this device.

332010_Schweissgeraet_PESG_120_B4_content_LB4.indb 8 28.11.19 17:13

GB 9

Safety instructions

PLEASE NOTE!

fThe use of the term ‘product’ or ‘device’

in the following text refers to the PESG

120 B4 arc welder named in these

operating instructions.

 This device may be used by

children aged 16 years and

older, and by persons with

reduced physical, sensory or

mental capacities, or a lack of

experience and knowledge,

if they are supervised or have

been instructed in how to use

the device safely and under

-

stand the dangers that may

arise when using it. Do not

allow children to play with the

device. Cleaning and day-to-

day maintenance must not be

performed by children without

supervision.

 Repairs and/or maintenance

work must only be carried out

by qualiﬁed electricians.

 Only use the welding cables

(PESG 120 B4 H01N2-D1 x

10 mm²) included in the scope

of delivery.

 During operation, the device

should not be positioned

directly on the wall, covered or

jammed between other devices

so that sufﬁcient air can be

absorbed through the ventila

-

tion slats.

Makes sure that the device

is correctly connected to the

supply voltage. Avoid any form

of tensile stress of the power

cable. Disconnect the plug from

the socket prior to setting up the

device in another location.

 If the device is not in operation,

always switch it off by pressing

the ON/OFF switch. Place the

electrode holder on an insulated

surface and only remove it from

the holder after allowing it to

cool down for 15 minutes.

 Pay attention to the condition

of the welding cable, electrode

holder and the earth terminal.

Wear and tear of the insulation

and the live parts can lead to

hazards and reduce the quality

of the welding work.

 Arc welding creates sparks,

molten metal parts and smoke.

Therefore ensure that: All

ﬂammable substances and/or

materials are removed from the

work station and its immediate

surrounding.

 Ensure the work station is

ventilated.

332010_Schweissgeraet_PESG_120_B4_content_LB4.indb 9 28.11.19 17:13

GB10

 Do not weld on containers,

vessels or tubes that contain or

contained ﬂamm

able liquids or

gases.

Avoid any form of

direct contact with the welding

current circuit. The open circuit

voltage between the electrode

holder and earth terminal can

be

dangerous, there is a risk of

electric shock.

 Do not store or use the device

in a damp or wet environment

or in the rain. Protection rating

IP21S is applicable in this case.

 Protect your eyes using the

appropriate protective glasses

(DIN level 9-10), which are

fastened to the supplied weld

-

ing mask. Wear gloves and dry

protective clothing that are free

of oil and grease to protect the

skin from exposure to ultraviolet

radiation of the arc.

Do not use the

welding current source to

defrost pipes.

Please note:

 The light radiation emitted by

the electric arc can damage

eyes and cause burns to the

skin.

 Arc welding creates sparks

and drops of melted metal.

The welded workpiece starts to

glow and remains hot for a

relatively long period.

Therefore, do not touch the

workpiece with bare hands.

 Arc welding can cause vapours

to be release that may be

hazardous to health. Be careful

not to inhale these vapours.

 Protect yourself from the harm-

ful effects of the electric arc

and keep people that are not

involved in the work away from

the arc maintaining a distance

of at least 2 m.

ATTENTION!

 During the operation of the

welding device, other consum

-

ers may experience problems

with the voltage supply depend

-

ing on the network conditions

at the connection point. In case

of doubt, please contact your

energy supply company.

 During the operation of the

welding device, other devices

may malfunction, e.g. hearing

aids, cardiac pacemakers, etc.

Safety instructions

332010_Schweissgeraet_PESG_120_B4_content_LB4.indb 10 28.11.19 17:13

GB 11

 Potential hazards during

electric arc welding

There are a series of potential

hazards that can occur during

electric arc welding. It is therefore

particularly important for the

welder to observe the following

rules to avoid endangering him/

herself and others and to prevent

damage to people and the

device.

 Work on the voltage side,

e.g. on cables, plugs, sockets

etc., may only be carried

out by qualiﬁed electricians

according to national and local

regulations.

 In the event of accidents,

disconnect the welding

devoice from the mains voltage

immediately.

 If electrical contact voltages

occur, switch off the device

immediately and make sure you

have it checked by a qualiﬁed

electrician.

 Always ensure good electrical

contacts on the welding current

side.

 Always wear insulating gloves

on both hands during welding

work. These provide protection

from electrical shocks (open

circuit voltage of the welding

current circuit), harmful radia

-

tions (heat and UV radiation)

and incandescent metal and

splashes of slag.

 Wear sturdy, insulating shoes.

The shoes should also insulate

when exposed to moisture.

Loafers are not suitable as fall-

ing incandescent metal droplets

can cause burns.

 Wear suitable protective cloth-

ing, no synthetic garments.

 Do not look into the electric arc

without eye protection; only

use a welding mask with the

prescribed protective glass as

per DIN. In addition to light

and heat radiation, which can

dazzle or cause burns, the elec-

tric arc also emits UV radiation.

Without suitable protection the

invisible ultraviolet radiation

can cause very painful conjunc-

tivitis which is not apparent

until several hours later.

Furthermore, UV radiation can

cause burns with sunburn-like

effects on unprotected parts of

the body.

 Any persons in the vicinity of

the electric arc or helpers must

also be informed of the dangers

and be equipped with the

necessary protective equipment.

Safety instructions

332010_Schweissgeraet_PESG_120_B4_content_LB4.indb 11 28.11.19 17:13

GB12

Safety instructions

If necessary, set up protective

walls.

 Ensure an adequate supply

of fresh air whilst welding,

particularly in small spaces, as

it produces smoke and harmful

gases.

 No welding work may be

carried out on containers that

have been used for storing

gases, fuels, mineral oils or

similar – even if they have been

empty for a long time – as

possible residues may present

a risk of explosion.

 Special regulations apply in

rooms where there is a risk of

ﬁre or explosion.

 Welded joints that are subject

to heavy stress loads and are

required to comply with certain

safety requirements may only

be carried out by specially

trained and certiﬁed welders.

Examples of this are pressure

vessels, running rails, tow

bars, etc.

ATTENTION!

Always connect

the earth terminal as close as

possible to the point of weld to

provide the shortest possible

path for the welding current

from the electrode to the earth

terminal. Never connect the

earth terminal to the housing

of the welding device!

Never connect the earth

terminal to earthed parts far

away from the workpiece,

e.g. a water pipe in another

corner of the room. This could

otherwise damage the protec-

tive bonding system of the room

you are welding.

 Do not use the welding device

in the rain.

 Do not use the welding device

in a moist environment.

 Only place the welding device

on a level surface.

 The outlet is measured at an

ambient temperature of 20°C

and welding time can be

reduced in the event of higher

temperatures.

Risk of electric shock:

Electric shock from the

welding electrode can be

fatal. Do not weld in rain or snow.

Wear dry insulating gloves.

Do not touch the electrodes with

bare hands. Do not wear wet or

damaged gloves. Protect yourself

from electric shock with insulation

against the workpiece. Do not open

the device housing.

Danger from welding fumes:

Inhalation of welding fumes can

endanger health. Do not keep

332010_Schweissgeraet_PESG_120_B4_content_LB4.indb 12 28.11.19 17:13

GB 13

Safety instructions

your head in the fumes. Use the

equipment in open areas. Use

extractors to remove the fumes.

Danger from welding sparks:

Welding sparks can cause

an explosion or ﬁre. Keep ﬂam-

mable substances away from the

welding location.

Do not weld next to ﬂammable

substances. Welding sparks can

cause ﬁres. Keep a ﬁre extin

-

guisher close by and an observer

should be present to be able to

use it immediately. Do not weld

on drums or any other closed

containers.

Danger from arc beams:

Arc beams can damage your eyes

and injure your skin. Wear a hat

and safety goggles. Wear hearing

protection and high, closed shirt

collars. Wear a welding safety

helmet and make sure that the ﬁl

-

ter setting is right. Wear complete

body protection.

Danger from

electro magnetic ﬁelds

Welding current generates electro

-

magnetic ﬁelds. Do not use if

you have a medical implant.

Never wrap the welding cable

around your body. Guide welding

cables together.

 Welding mask-speciﬁc

safety instructions

 With the help of a bright light

source (e.g. lighter) examine

the proper functioning of the

welding mask prior to starting

with any welding work.

 Weld spatters can damage the

protective screen. Immediately

replace damaged or scratched

protective screens.

 Immediately replace damaged

or highly contaminated or

splattered components.

 The device must only be oper-

ated by people over the age

of 16.

 Please familiarise yourself with

the welding safety instructions.

Also refer to the safety instruc

-

tions of your welding device.

 Always wear a welding mask

while welding. If it is not used,

you could sustain severe lesions

to the retina.

 Always wear protective clothing

during welding operations.

332010_Schweissgeraet_PESG_120_B4_content_LB4.indb 13 28.11.19 17:13

GB14

Safety instructions

 Never use the welding mask

without the protective screen

because this could damage the

optical unit.

 Regularly replace the protective

screen to ensure good visibility

and fatigue-proof work.

 Environment with

increased electrical

hazard

Environments with increased

electrical hazard may be

encountered, for example:

 In workplaces where the space

for movement is restricted,

such that the operator is

working in a forced posture

(e.g.: kneeling, sitting, lying)

and is touching electrically

conductive parts;

 In workplaces which are

restricted completely or in

part in terms of electrical

conductivity and where there is

a high risk through avoidable

or accidental touching by the

operator;

 In wet, humid or hot work-

places where the air humidity

or weld signiﬁcantly reduces

the resistance of human skin

and the insulating properties

or effect of protective

equipment.

Even a metal conductor or

scaffolding can create an

environment with increased

electrical hazard.

When using welding devices

under electrically dangerous con-

ditions, the output voltage of the

welding device must be greater

than 35 volt when idling (effec-

tive value). Based on the output

voltage this welding device may

not be used in these conditions.

 Welding in tight spaces

When welding in tight spaces this

may pose a hazard through toxic

gases (risk of suffocation). In tight

spaces the device may only be

operated if there are trained indi-

viduals in the immediate vicinity

who can intervene if necessary.

In this case, before starting to use

the welding device, an expert

must carry out an assessment in

order to determine what steps are

necessary, in order to guarantee

safety at work and which pre-

cautionary measures should be

taken during the actual welding

procedure.

332010_Schweissgeraet_PESG_120_B4_content_LB4.indb 14 28.11.19 17:13

GB 15

Safety instructions

 Total of open circuit

voltages

When more than one welding

current source is operated at

the same time, their open circuit

voltages may add up and lead to

an increased electrical hazard.

The welding current sources

must be clearly marked with

their individual control units and

connections, in order to be able

to identify which device belongs

to which circuit.

 Protective clothing

 At work, the welder must

protect his/her whole body

by using appropriate clothing

and face protection against

radiations and burns.

The following steps must be

observed:

- Wear protective clothing

prior to welding work.

- Wear gloves.

- Open windows or use a fan

to guarantee air supply.

- Wear safety glasses and a

face mask.

 Gauntlet gloves made of a

suitable material (leather) must

be worn on both hands. They

must be in perfect condition.

 A suitable apron must be

worn to protect clothing from

ﬂying sparks and burns.

When speciﬁc work, e.g.

overhead welding, is required,

a protective suit must be worn

and, if necessary, even head

protection.

 Protection against rays

and burns

 Warn of the danger to the eyes

by hanging up a sign saying

“Caution! Do not look into

ﬂames!”. The workplaces must

be shielded so that the persons

in the vicinity are protected.

Unauthorised persons must be

kept away from welding work.

 The walls in the immediate

vicinity of ﬁxed workplaces

should neither be bright

coloured or shiny. Windows

up to head height must be

protected to prevent rays

from penetrating or reﬂecting

through them, e.g. by using

suitable paint.

332010_Schweissgeraet_PESG_120_B4_content_LB4.indb 15 28.11.19 17:13

GB16

 EMC Device Classiﬁcation

As per the standard

IEC 60974-10, this welding

device is a welding unit with

class B electromagnetic compat-

ibility. Thus it complies with the

corresponding requirements for

commercial and domestic use.

In residential areas, it can be

connected to the public low-

voltage supply network.

Even if the welding device

complies with the emission limit

values of the standard, arc welding

devices can still result in electro

-

magnetic interferences in sensitive

systems and devices.

The operator is responsible for

malfunctions that occur through

the arc while welding and must

take suitable protective measures.

In doing so, the operator must

consider the following:

– network, control, signal and

telecommunication lines

– computers and other micro-

processor-controlled devices

– TVs, radios and other playback

devices

– electronic and electrical safety

equipment

– people with cardiac pace-

makers or hearing aids

– measurement and calibration

devices

– interference immunity of other

equipment nearby

– the time at which the welding

work is carried out.

The following is recommended

to reduce possible interference

radiation:

– equip the mains connection

with a mains ﬁlter

– the welding device must be

regularly maintained and kept

in a good condition

– welding cables should be

completely uncoiled and run as

close to parallel with the ﬂoor

as possible

– devices and systems that are

compromised by the inter-

ference radiation must be

removed from the welding area

or shielded.

 Before use

 Take all parts from the packaging

and check whether the arc welder

or parts show any damage. If this is

the case, do not use the arc welder.

Contact the manufacturer via the

indicated service address.

 Remove all protective ﬁlms and other

transport packaging.

 Check that the delivery is complete.

Safety instructions / Before use

332010_Schweissgeraet_PESG_120_B4_content_LB4.indb 16 28.11.19 17:13

GB 17

Mounting / Using the device

 Mounting

 Fit welding mask

 Fit the handle

8

onto the welding

mask

7

, as shown in Fig. B.

 Fit the protective glass

10

onto the

welding mask

7

, as shown in Fig. B.

 The protective glass

10

must be

pushed in at the top.

Note: If it is not possible to push the

protective glass

10

in fully, then press

gently on the protective glass

10

from

the outside.

 Using the device

 Welding preparation

Note: If you adjust the current, check

whether the manual wheel

3

can still

move and that the lead screw is not

jammed.

Note: If the clamping force of the

electrode holder

5

and the earth

terminal

4

decreases, replace these

immediately.

 Connect the power cable.

 Set the ON/OFF switch

2

to the

“ON” position. The power indicator

lights up, the procedure can start.

 To stop the procedure, set the ON/

OFF switch

2

to the “OFF” position.

Note: If the yellow control lamp

6

lights up, then this indicates overheating.

The power circuit is shut off automati-

cally. The procedure is stopped.

Attach the earth terminal

4

straight

onto the workpiece or to the base on

which the workpiece is positioned.

Note: Make sure that there is direct

contact with the workpiece. You should

therefore avoid lacquered surfaces and/

or insulating materials.

Note: The welding mask

7

must

always be used during welding

operations.

It protects the eyes from the light radia-

tion emitted by the arc and therefore

permits a clear view of the workpiece.

Note: The weldable material thickness

is 1.5 - 3.0 mm.

 Welding

Once you have connected all the elec-

trical connections for the power supply

as well as for the welding current circuit,

proceed as follows:

 Insert the non-coated end of the

electrode into the electrode holder

5

and connect the earth terminal

4

with the workpiece. Please ensure

good electrical conductivity.

 The device has a detent to set the

electrode thickness. Switch the

device on by setting the ON/OFF

switch

2

to the “ON” position.

Then select the electrode thickness

using the manual wheel

3

: For 1.6

or 2.0 mm electrodes, set the manual

wheel

3

to the 1.6 / 2.0 position.

For 2.5 mm electrodes set the

manual wheel

3

to the 2.5 position.

 Hold the welding mask

7

in front of

your face and guide the tip of the

electrode over the workpiece as if

you were going to strike a match.

This is the best way to ignite the arc.

 Use a sample to test whether you

have the right electrode and current

strength on a sample.

ATTENTION!

Do not dab the workpiece with the

electrode. It could be damaged and

it could be more difﬁcult to ignite the

332010_Schweissgeraet_PESG_120_B4_content_LB4.indb 17 28.11.19 17:13

GB18

Using the device / Maintenance / Information about recycling and disposal

arc. As soon as the arc is ignited, try

to maintain a gap from the workpiece,

which is equivalent to the diameter of

the electrode used. The gap should

remain as constant as possible while

you are welding. The angle of the

electrode in the direction of operation

should be 20–30 degrees.

ATTENTION!

Always use pliers to remove used

electrodes or move hot workpieces.

Please note that the electrode holder

must always be placed onto an

insulated base after welding.

The slag can only be removed from

the seam once it has cooled down.

If welding continues on an intermittent

weld seam, then the slag should be

removed at the point of attachment ﬁrst.

ATTENTION!

Welding generates heat. For this

reason, after use the welding device

must be allowed to idle for at least half

an hour. Alternatively, let the device

cool off for an hour. The device can only

be packed and stored once the device

temperature has returned to normal.

 Switch the device OFF by setting the

ON/OFF switch

2

to the “OFF”

position.

 Overload protection

The welding device is protected against

overheating by means of an automatic

protection device. Allow the device to

cool down (approx. 15 min.) for the

activation of the protection device.

As soon as the control lamp

6

goes out,

the device is ready for operation again.

PESG 120 B4 (with AC 230 V 50Hz

mains plug):

The fuses of the supply lines to the

power sockets must comply with the

regulations (VDE 0100). Safety sockets

must be fused with max. 16A (type

and technical speciﬁcations: NDM1-63,

AC 230 / 400 V C16. IEC 60898.

slow blow trigger. Manufacturer: Nader)

(fuses or Miniature circuit-breakers).

Higher levels of fuse protection can

result in cable ﬁre or structural ﬁre

damage.

Attention: The device must be

connected to a power source with

the fuse as speciﬁed above. If the

electrode holder and earth terminal are

short circuited, the fuse can trigger in

16-20seconds. Classiﬁcation in accord-

ance with the EMC Directive: Class B in

accordance with IEC 60974-10.

 Maintenance

 Remove dust and contamination from

the device regularly.

 Clean the device and accessories

with a ﬁne brush or a dry cloth.

 Information about

recycling and disposal

Don’t throw away – recycle!

Please return this device, accesso-

ries and packaging to your local

recycling

depot.

Do not dispose of the arc welder in

household waste, in ﬁre or in water.

Devices that are no longer functional

should be recycled wherever possible.

Ask your local stockist for advice.

332010_Schweissgeraet_PESG_120_B4_content_LB4.indb 18 28.11.19 17:13

GB 19

 EU Declaration of

Conformity

We,

C. M. C. GmbH

Responsible for documentation:

Dr Christian Weyler

Katharina-Loth-Str. 15

66386 St. Ingbert

GERMANY

hereby take sole responsibility for

declaring that the product

Arc welder

Item number: 2251

Year of manufacture: 18 / 2020

IAN: 332010_1907

Model: PESG 120 B4

meets the basic safety requirements as

speciﬁed in the European Directives

EC low-voltage directive

2014 / 35 / EU

EC Guideline on Electromagnetic

Compatibility

2014 / 30 / EU

RoHS directive

2011 / 65 / EU + 2015 / 863 / EU

and the amendments to these Directives.

The manufacturer will be solely responsi-

ble for the creation of the declaration of

conformity.

The object of the declaration described

above meets the requirements of

Directive 2011/65/EU of the Euro-

pean Parliament and of the Council of

8 June 2011 on the restriction of the

use of certain hazardous substances in

electrical and electronic equipment.

This conformity assessment is based on

the following harmonised standards:

EN 60974-10:2014/A1:2015

EN 60974-1:2016

EN 60974-6:2016

IEC 61000-3-11:2000

IEC 61000-3-12:2011

St. Ingbert, 15/10/2019

pp Dr Christian Weyler

– Quality Assurance –

 Warranty and service

information

Warranty from Creative Marketing &

Consulting GmbH

Dear Customer,

The warranty for this equipment is

3years from the date of purchase. In the

event of product defects, you have legal

rights against the retailer of this product.

Your statutory rights are not affected in

any way by our warranty conditions,

which are described below.

 Warranty conditions

The warranty period begins on the date

of purchase. Please retain the original

sales receipt. This document is required

as your proof of purchase.

Should this product show any defect in

materials or manufacture within 3years

from the date of purchase, we will

repair or replace it – at our discretion –

free of charge.

EU Declaration of Conformity / Warranty and service information

332010_Schweissgeraet_PESG_120_B4_content_LB4.indb 19 28.11.19 17:13

GB20

This warranty service requires that you

retain proof of purchase (sales receipt)

for the defective device for the three

year period and that you brieﬂy explain

in writing what the fault entails and

when it occurred.

If the defect is covered by our warranty,

we will repair and return your product

or send you a replacement. The original

warranty period is not extended when a

device is repair or replaced.

 Warranty period and

statutory claims for

defects

The warranty period is not extended

by the guarantee. This also applies to

replaced and repaired parts. Any dam-

ages or defects detected at the time of

purchase must be reported immediately

after unpacking. Any incidental repairs

after the warranty period are subject to

a fee.

 Extent of warranty

This device has been manufactured

according to strict quality guidelines and

carefully inspected before delivery.

The warranty applies to material

and manufacturing defects only. This

warranty does not extend to product

parts, which are subject to normal wear

and tear and can thus be regarded as

consumable parts, or for damages to

fragile parts, e.g. switches, recharge-

able batteries or parts made from glass.

This warranty is voided if the product

becomes damaged or is improperly

used or maintained. For proper use

of the product, all of the instructions

given in the operating instructions must

be followed precisely. If the operating

instructions advise you or warn you

against certain uses or actions, these

must be avoided in all circumstances.

The product is for consumer use only and

is not intended for commercial or trade

use. The warranty becomes void in the

event of misuse and improper use, use

of force, and any work on the device

that has not been carried out by our

authorised service branch.

 Processing of warranty

claims

To ensure prompt processing of your

claim, please follow the instructions

given below.

Please retain proof of purchase and the

article number (e.g. IAN) for all inquiries.

The product number can be found on

the type plate, an engraving, the cover

page of your instructions (bottom left), or

the sticker on the back or underside of

the device.

In the event of malfunctions or other

defects, please ﬁrst contact our service

department below by phone or email.

If your product is found to be defective,

you can then send your product with

proof of purchase (till receipt) and a

statement describing what the fault

involves and when it occurred free of

charge to the service address given.

Note:

You can download this hand-

book and many more, as well as

product videos and software at

www.lidl-service.com.

Warranty and service information

332010_Schweissgeraet_PESG_120_B4_content_LB4.indb 20 28.11.19 17:13

Stránka sa načítava...

Parkside 332010 1907 Operation and Safety Notes

Tento návod je vhodný aj pre

Parkside 332010 1907 Operation and Safety Notes

v iných jazykoch

Súvisiace články

Ostatné dokumenty