Parkside PDWS 125 A1 Operating Instructions Manual

IAN 276009

AIR ANGLE GRINDER PDWS 125 A1

AIR ANGLE GRINDER

Operating instructions

DRUCKLUFT-WINKELSCHLEIFER

Bedienungsanleitung

PNEUMATIKUS SAROKCSISZOLÓ

Használati utasítás

KOTNI BRUSILNIK NA STISNJEN ZRAK

Navodila za uporabo

PNEU ÚHLOVÁ BRUSKA

Návod k obsluze

PNEUMATICKÁ UHLOVÁ BRÚSKA

Návod na obsluhu

GB Operating instructions Page 1

HU Használati utasítás Oldal 15

SI Navodila za uporabo Stran 29

CZ Návod k obsluze Strana 43

SK Návod na obsluhu Strana 57

DE / AT / CH Bedienungsanleitung Seite 71

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of

the device.

Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik

funkcióját.

Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.

Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.

Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

PDWS 125 A1

GB

│

1 ■

Contents

Introduction ......................................................2

Intended use ................................................................ 2

Features ................................................................... 2

Package contents ............................................................ 3

Technical data .............................................................. 3

General safety rules ...............................................3

Hazards caused by ﬂying parts ................................................. 4

Hazards caused by entanglement ............................................... 4

Hazards during operation ..................................................... 4

Risks due to repetitive movements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Hazards caused by accessories ................................................. 5

Hazards in the workplace ..................................................... 6

Risks due to dust and vapours .................................................. 6

Risks due to noise ............................................................ 6

Risks due to vibrations ........................................................ 7

Additional safety instructions for pneumatic machines ................................ 7

Special safety instructions for grinding and abrasive cutting ........................... 8

Additional special safety instructions for abrasive cutting ............................. 8

Kickback and corresponding safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Operation .......................................................9

Attaching the auxiliary handle .................................................. 9

Attaching the protective cover .................................................. 9

Attaching the grinding disc ....................................................10

Fitting the connector nipple ................................................... 10

Operation ................................................................. 11

Working procedures ......................................................... 11

Maintenance and cleaning .........................................12

Disposal ........................................................12

Warranty .......................................................12

Service .........................................................13

Importer .......................................................13

Translation of the original Conformity Declaration .....................13

PDWS 125 A1

■ 2

│

GB

AIR ANGLE GRINDER

PDWS 125 A1

Introduction

Congratulations on the purchase of your new ap-

pliance. You have selected a high-quality product.

The operating instructions are part of this product.

They contain important information on safety, usage

and disposal. Before using the product, please

familiarise yourself with all operating and safety

instructions. Use the product only as described and

for the speciﬁed areas of application. Please also

pass on these operating instructions to any future

owner.

Intended use

The compressed air tool is intended for grinding

and abrasive cutting metal and similar materials

without the use of water. Any other use of or modi-

ﬁcation to the machine is deemed to be improper

and carries the risk of serious personal injury.

Not for commercial use.

Explanation of the symbols

WARNING!

Read the instruction manual

before use.

Wear safety goggles!

Rotation direction

Oil daily!

P03/2016 Production date

V03/2019 Expiry date

Read the original operating

instructions and safety instructions

before initial operation.

Wear ear protection!

Wear sturdy work boots!

Wear protective gloves!

Wear a dust mask!

Not approved for wet grinding

Using damaged cutting or grin-

ding discs is dangerous and may

cause serious injury!

Intended for metal grinding

Diameter of the disc

Features

Air connection with ﬁlter

Plug nipple 1/4"

ON/OFF switch

Safety lock-out

Protective cover

Spindle

Auxiliary handle

Rear clamping ﬂange

Grinding disc

Front ﬂange

Open-ended spanner

Two-hole spanner

Oil container

Teﬂon tape

Hex key

PDWS 125 A1

GB

│

3 ■

Package contents

1 air angle grinder PDWS 125 A1

1 auxiliary handle

1 grinding disc (Ø 125mm)

1 two-hole spanner

1 open-ended spanner

1 hex key

1m PTFE tape

1 plug nipple (1/4")

1 oil container

1 operating manual

Technical data

Rated speed: 10000 rpm

Rated air pressure: max. 6.3 bar

Disc size: Ø 125 mm

Threaded mounting: M14

Plug nipple: 1/4"

Weight (with auxiliary handle): approx. 1.72 kg

Noise emission values:

Noise measurement determined in accordance

with ISO 15744.

Sound pressure level: L

pA

= 90.2 dB(A)

Uncertainty: K

pA

= 3 dB(A)

Sound power level: L

WA

= 101.2 dB(A)

Uncertainty: K

WA

= 3 dB(A)

Vibration emission value:

Vibration emission value determined in accordance

with ISO 28927-1 and EN 12096:

a

h

= 2.44 m/s

2

Uncertainty K = 1.5 m/s

2

WARNING!

General

safety rules

WARNING!

► For multiple hazards: Please ensure that you

have read and understood the safety instruc-

tions before adjusting, operating, repairing,

maintaining or replacing accessories on the

angle grinder as well as before working in

the vicinity of the machine. Failure to do this

can result in serious bodily injury.

■ The grinding machine for abrasive media should

only be adjusted, set or used by adequately

qualiﬁed and trained operators.

■ This machine may not be modiﬁed. Modiﬁcations

can reduce the eﬀectiveness of the safety meas-

ures and increase the risks for the operator.

■ Do not lose the safety instructions – hand them

to the operator.

■ Never use damaged grinding machines for

abrasive media.

PDWS 125 A1

■ 4

│

GB

Hazards caused by ﬂying parts

■ If a workpiece or accessory or even part of the

machine tool itself breaks, parts can be ﬂung

out at high speeds.

■ Always wear shock-resistant eye protection when

operating the grinding machine for abrasive

media. The degree of necessary protection must

be evaluated separately for each individual

task.

■ You must ensure that the workpiece has been

securely ﬁxed.

■ You must ensure that the abrasive media has

been safely attached to the grinding machine

for abrasive media.

■ You must ensure that the maximum operating

rotational speed of the abrasive media calcu-

lated in revolutions per minute is the same as

or higher than the rated spindle speed.

■ Ensure that the protective guard has been ﬁtted,

that it is in good condition and properly ﬁxed,

and that it is regularly checked.

■ It is possible that no protective guard is required

during internal grinding under the condition that

the workpiece encloses the abrasive media.

■ You must ensure that the clamping ﬂange is be-

ing used in accordance with the manufacturer's

instructions and that it is in good condition, i.e.

without cracks and ﬂaws, and that it is ﬂat.

■ You must check to see whether the spindle and

spindle thread have become damaged or worn.

■ You must ensure that any sparks or ashes

produced during operation do not cause any

hazards.

■ Always disconnect the grinding machine from

the power supply before replacing the abrasive

media or servicing it.

Hazards caused by entanglement

■ Suﬀocation, scalping and/or cut wounds can

occur if loose clothing, jewellery, necklaces, hair

or gloves are not kept away from the machine

and its accessories.

Hazards during operation

■ Avoid contact with the rotating spindle and the

ﬁtted grinding disc in order to avoid cuts to the

hands and other body parts.

■ When using the machine, the operator's hands

can be subject to hazards such as cuts, grazing

and heat. Wear suitable gloves to protect your

hands.

■ The operator and maintenance personnel must

be physically capable of handling the size, mass

and power of the machine.

■ Hold the machine correctly:

Be ready to counteract any normal or suddenly

occurring movements. Keep both hands ready

for use.

■ Ensure that your body is balanced and that you

have a secure standing position.

■ Release the start/stop control if there is a disrup-

tion to the power supply.

■ Use only the recommended lubricants.

■ Safety goggles must be worn; wearing of protec-

tive gloves and safety clothing is recommended.

■ Wear a safety helmet if working above head

height.

■ Do not put the machine down after switching

oﬀ until the disc has stopped rotating.

■ When abrasive cutting, the workpiece must be

supported so that the cutting slot has a constant

or increasing width during the entire cutting

process.

■ If the abrasive media jams in the cutting slot, the

grinding machine for abrasive media must be

turned oﬀ and the grinding disc must be loos-

ened. Before continuing operation, check that

the abrasive media is still properly ﬁxed and

has not been damaged.

PDWS 125 A1

GB

│

5 ■

■ Grinding discs and abrasive cutting discs may

not be used for side grinding (exception: grind-

ing discs for side grinding). Grinding machines

for abrasive media may only be operated at a

rotation speed which is less than the abrasive

media maximum speed;

■ ensure that no persons are standing in the im-

mediate vicinity.

■ Personal safety equipment such as suitable

gloves, aprons and protective helmets must be

worn.

■ Sparks caused by grinding can ignite clothing

and cause serious burns. You must ensure that

sparks do not impact clothing. Wear ﬁre-retard-

ant clothing and ensure that there is a bucket of

water in the vicinity.

Risks due to repetitive movements

■ When using a grinding machine for abrasive

media to perform work-related activities, opera-

tors may experience uncomfortable sensations

in their hands and arms, as well as in the neck

and shoulders or other parts of the body.

■ When using a grinding machine for abrasive

media, the operator should adopt a comfort-

able posture whilst ensuring a secure hold

and avoiding awkward postures or positions

in which it is diﬃcult to maintain balance. The

operator should change positions during the

course of long-lasting tasks. This can be helpful

in the prevention of discomfort and fatigue.

■ If the operator notices symptoms such as persis-

tent or recurring illness, discomfort, throbbing,

pain, tingling, burning or stiﬀness, these indica-

tions should not be ignored. In this case, the

operator should inform his/her employer and

consult a suitably qualiﬁed physician.

Hazards caused by accessories

■ Disconnect the grinding machine for abrasive

media from the power supply before ﬁtting or

replacing the machine tools or accessories.

■ Use only accessories and supplies of the sizes

and types recommended by the manufacturer

of the grinding machine for abrasive media.

Never use any other types or sizes of accessory

parts and consumables.

■ Ensure that the dimensions of the abrasive me-

dia are compatible with those of the grinding

machine for abrasive media and that the abra-

sive media ﬁts onto the spindle.

■ Ensure that the thread type and size of the

abrasive media exactly matches the thread type

and size of the spindle thread.

■ Always inspect the abrasive media before use.

Do not use any abrasive media which may

have been dropped or which shows signs of

splintering, cracking or other ﬂaws.

■ Always ensure that the abrasive media has

been properly ﬁxed and tightened ﬁrmly

enough before use; the grinding machine for

abrasive media must be operated at idling

speed for at least 1 minute in a safe location;

switch oﬀ the machine immediately if you notice

excessive vibration or any other damage; the

cause of these malfunctions must be determined.

■ Ensure that the spindle end does not contact the

bottom of the openings in cut wheels, grinding

cones or whetstones with thread inserts which

are intended for the attachment of machine

spindles, by checking the dimensions and other

important spindle data.

■ In the case of abrasive media which are sup-

plied with reducers or reducing bushings, or

which are intended for use with reducers or

reducing bushings, the operator must ensure

that the reducer or reducing bushing does not

contact the face of the clamping ﬂange and that

the clamping force provides suﬃcient rotational

drive to prevent slipping of the abrasive media.

■ In cases in which clamping ﬂanges for diﬀerent

types and sizes of abrasive media have been

provided, always ﬁt the correct clamping ﬂange

for the abrasive media being used.

■ Avoid direct contact before and after use of the

machine tool since it can be hot or have sharp

edges.

■ The abrasive media must be handled and stored

in accordance with the manufacturer's instruc-

tions.

PDWS 125 A1

■ 6

│

GB

Hazards in the workplace

■ Slipping, tripping up and falling are the main

causes of injuries at the workplace. Look out

for surfaces which could have become slippery

through use of the machine, and also any trip-

ping hazards caused by air or hydraulic hoses.

■ Proceed with caution in unknown surroundings.

Hidden hazards caused by power or other

supply lines may be present.

■ The grinding machine for abrasive media is not

intended for use in explosive atmospheres and

is not insulated against contact with electrical

power sources.

■ Ensure that no electrical service lines, gas pipes,

etc., which could cause a hazard if damaged

by use of the machine are present.

Risks due to dust and vapours

■ The dust and vapours produced by using the

grinding machine for abrasive media and pol-

ishing can be hazardous to health (e.g. cause

cancer, birth defects, asthma and/or dermati-

tis); it is essential to carry out a risk assessment

in respect of these risks and to implement cor-

responding regulatory mechanisms.

■ The risk assessment should include all dust

caused by the use of the machine and any

existing dust that may be whirled up at the

same time.

■ The grinding machine for abrasive media must

be operated and maintained in accordance

with the recommendations contained in this

manual to keep the release of dust and vapours

to a minimum.

■ The exhaust air should be routed so that the

raising of dust in already dusty environments is

kept to a minimum.

■ If dusts or vapours are created, the main priority

must be to control these at the site of their re-

lease.

■ All inserts or accessories of the machine in-

tended for collecting, extracting or suppressing

airborne dust or vapours or should be used and

serviced in accordance with the manufacturer’s

instructions.

■ Consumables/machine tools should be se-

lected, maintained and replaced in accordance

with the recommendations in this guide in order

to avoid unnecessary intensiﬁcation of dust or

vapour production.

■ Use breathing equipment as per the instructions

provided by your employer or as required by

health and safety regulations.

■ Processing certain materials can cause emission

of dust and vapours which, in turn, can result in

the formation of an explosive environment.

Risks due to noise

■ Exposure to high noise levels can result in per-

manent hearing damage, loss of hearing and

other problems such as tinnitus (ringing, rushing,

whistling or buzzing in the ear) if suﬃcient hear-

ing protection is not being worn.

■ Suitable regulatory mechanisms include meas-

ures such as the use of insulation materials to

avoid pinging occurring on the workpieces.

■ Use hearing protection.

■ The grinding machine for abrasive media is to

be operated and maintained in accordance

with the recommendations contained in this

manual to reduce any unnecessary increase

of the noise levels.

■ If the grinding machine for abrasive media is

equipped with a silencer, always ensure that

this in its place and is operational while the

machine is in operation.

■ Consumables/machine tools should be selected,

maintained and replaced in accordance with

the recommendations in this guide in order to

avoid unnecessary increase of the noise levels.

PDWS 125 A1

GB

│

7 ■

Risks due to vibrations

■ Vibrations can damage the nerves and cause

problems with the blood circulation in the hands

and arms.

■ When working in a cold environment, wear

warm clothing and keep your hands warm and

dry.

■ If you notice numbness, tingling or pain in your

ﬁngers or hands or notice that the skin of your

ﬁngers or hands has become pale, stop work-

ing with the grinding machine for abrasive me-

dia, inform your employer and consult a doctor.

■ The grinding machine for abrasive media must

be operated and maintained in accordance

with the recommendations contained in this

manual to reduce any unnecessary increase of

the vibrations.

■ Do not allow the machine tool to rattle against

the workpiece since this would very probably

result in a considerable increase in the vibra-

tions.

■ Consumables/machine tools must be selected,

maintained and replaced in accordance with

the recommendations in this guide in order to

avoid any unnecessary increase in vibration.

■ Always use a stand, a clamp or a compensation

device to support the weight of the machine.

■ Hold the machine securely but not too ﬁrmly

while maintaining the necessary hand-reaction

force, as the vibration risk generally increases

the harder the machine is held.

■ Use intermediate layers if these are intended for

the bonded abrasive media.

Additional safety instructions for

pneumatic machines

■ Compressed air can cause serious injuries.

– Ensure that the air supply is switched oﬀ,

the hose is not under pressure and that the

machine is disconnected from the air supply

when not in use, and also before exchang-

ing accessories or carrying out repairs.

– Never aim the airﬂow towards yourself or

any other person.

■ Thrashing hoses can cause serious injury. There-

fore, always check that the hoses and their ﬁx-

ings are not damaged or have not come loose.

■ If universal rotary joints (claw couplings) are

used, locking pins must be used to provide pro-

tection; Whipchek

®

air hose restraints must be

used to provide protection in case of a failure of

the connection of the hose to the machine.

■ Ensure that the maximum permissible pressure

stated on the machine is not exceeded.

■ Never carry compressed air-powered machines

by the hose.

PDWS 125 A1

■ 8

│

GB

Special safety instructions for

grinding and abrasive cutting

■ Use only the grinding accessories approved for

your compressed air tool and the appropriate

protective cover for these grinding tools. Grind-

ing tools which are not designed for the com-

pressed air tool can not be suﬃciently shielded

and are unsafe.

■ Cranked grinding discs must be ﬁtted so that

their grinding surfaces do not protrude above

the level of the protective cover edge. An im-

properly mounted grinding disc which protrudes

beyond the edge of the protective cover cannot

be suﬃciently screened.

■ The protective cover must be securely ﬁxed

to the compressed air tool and adjusted to

ensure maximum safety so that the smallest

possible amount of the grinding tool is ex-

posed to the operator. The protective cover is

designed to protect the operator from fragments

and accidental contact with the grinding tool.

■ Grinding tools should only be used for the

recommended applications. For example:

Never grind with the side surface of a cut-

ting disc. Cutting discs are designed to remove

material with the edge of the disc. Any lateral

application of force on these grinding tools can

lead to breakage.

■ Always use an undamaged clamping ﬂange

of the correct size and shape for the grind-

ing disc you have selected. Suitable ﬂanges

support the grinding disc and reduce the risk of

disc breakage. Flanges for cutting discs can be

diﬀerent to ﬂanges for other grinding discs.

■ Do not use worn grinding discs from larger

compressed air tools. Grinding discs for larger

compressed air tools are not designed for the

higher rotational speeds of smaller compressed

air tools and can break.

Additional special safety instructions

for abrasive cutting

■ Avoid cutting disc jams or excessive contact

pressure. Do not make any excessively deep

cuts. Overloading the cutting disc increases the

stress and likelihood of tilting or jamming and

thus the possibility of kickback or breakage of

the grinding tool.

■ Avoid the area in front of and behind the

rotating cutting disc. When you move the cut-

ting disc away from yourself in the workpiece it

is possible, in the event of a kickback, that the

compressed air tool along with the rotating disc

might be thrown out directly towards you.

■ If the cutting disc jams or you stop working,

switch the tool oﬀ and hold it steady until the

disc has come to a complete standstill. Never

attempt to pull a rotating cutting disc out of a

cut. This could lead to kickback. Identify and

remove the cause of the jam.

■ Do not switch the compressed air tool back

on while it is in the workpiece. Allow the cut-

ting disc to reach its full speed before you

carefully continue the cut. Otherwise, the disc

can jam, jump out of the workpiece or cause

kickback.

■ Support panels or large workpieces to re-

duce the risk of the cutting disc jamming and

causing a kickback. Large workpieces can

bend under their own weight. The workpiece

must be supported on both sides of the disc:

both in the vicinity of the cutting disc and also

at the edge.

■ Be particularly careful when making "pocket

cuts" into existing walls or other obscured ar-

eas. The inserted cutting disc may cut into gas

or water pipes, electrical wiring or other objects

that can cause kickback.

Kickback and corresponding safety

instructions

■ Kickback is a sudden reaction caused when a

rotating accessory tool catches or jams.

■ Catching or jamming causes the rotating acces-

sory tool to stop abruptly.

PDWS 125 A1

GB

│

9 ■

If this happens, an uncontrolled compressed

air tool turns rapidly against the direction of

rotation of the accessory tool caught in the

blockage.

■ If, for example, a grinding disc catches or jams

in a workpiece, the edge of the grinding disc

that is projecting into the workpiece can get

caught and break oﬀ the grinding disc or cause

a kickback. The grinding disc can then ﬂy in

the direction of the operator or away from him,

depending on the direction of rotation of the

disc at the blockage.

This can also break grinding discs.

■ A kickback is caused by incorrect use or misuse

of the compressed air tool. This can be avoided

by taking proper precautions as given below.

a) Hold the compressed air tool ﬁrmly

in both hands and position your body and

arms so they can absorb the force of a

kickback. Always use the auxiliary handle,

if available, so you have maximum control

over the kickback force or reaction torques

at full speed. By taking adequate precau-

tions, the operator can stay in control of the

kickback and reaction torques.

b) Never hold your hand close to rotat-

ing accessory tools. The accessory tool

could move across your hand in the event

of a kickback.

c) Keep all parts of your body outside

the region in which the compressed air tool

is likely to move in event of a kickback. The

kickback will force the compressed air tool

in the opposite direction to the direction of

rotation of the grinding disc at the block-

age.

d) Take special care when working

around corners, sharp edges, etc. Avoid

allowing the accessory tool to bounce back

from the workpiece, or jam. The rotating ac-

cessory tool is more likely to jam in corners

or sharp edges or if it bounces. This can

cause a loss of control or kickback.

e) Do not use chains or toothed saw

blades. Such accessories often cause a kick-

back or loss of control over the power tool.

Operation

NOTE

► Screw the plug nipple

on before ﬁrst use.

Attaching the auxiliary handle

CAUTION!

► Do not work with the tool if the auxiliary

handle

is not attached!

♦ Screw the auxiliary handle

ﬁrmly onto the

left-hand or right-hand side of the machine.

Attaching the protective cover

CAUTION!

► For safety reasons, always use the protective

cover

!

■ The protective cover

is mounted on delivery

with 2 screws on the device.

♦ For rotation of the protective cover

, you ﬁrst

remove all screws with the hex key .

♦ Replace the protective cover

at most by a

hole added to the new position.

The closed side of the protective cover must

always be facing to the operator.

✓

✗

♦ Attach the protective cover with 3 screws on

the device.

Screw the remaining screw into the threaded

hole.

♦ Check for secure seating: The protective cover

must be securely attached.

Only use accessory tools

which the protective

cover protrudes be-

yond by at least 2 mm.

WARNING!

► The supplied protective cover

is for grinding

disc use only.

PDWS 125 A1

■ 10

│

GB

Attaching the grinding disc

CAUTION!

► Disconnect the compressed air tool from

the compressed air supply before replacing

the accessory tool or accessories, or before

carrying out adjustments or servicing. The

spindle

must be at a standstill.

Lock the spindle

♦ Place the rear clamping ﬂange

on the spindle

. This is correctly attached if the spindle

cannot be rotated.

♦ Place the open-ended spanner

supplied

over the collar of the rear clamping ﬂange to

prevent it from turning.

Attaching the grinding disc

♦ Place the grinding disc

on the rear clamping

ﬂange .

The grinding disc must be evenly placed on

the rear clamping ﬂange .

Fixing/loosening the front ﬂange

The 2 sides of the front ﬂange

are diﬀerent.

Screw the front ﬂange onto the spindle as

follows:

For thin grinding discs (see ﬁgure 1):

♦ The collar on the front ﬂange

faces upwards

so that the thin grinding disc can be safely

clamped.

12

≤ 3,2 mm

ﬁg. 1

For thick grinding discs (see ﬁgure 2):

> 3,2 mm

ﬁg. 2

The collar on the front ﬂange

faces downwards

so that the front ﬂange can be safely attached

to the spindle .

♦ Locking the spindle

.

♦ Tighten the front ﬂange

in a clockwise direc-

tion using the two-hole spanner .

Loosening the front ﬂange:

♦ Lock the spindle

.

♦ Undo the front ﬂange

in an anticlockwise

direction using the two-hole spanner .

Fitting the connector nipple

♦ Remove the plastic protective cap from the

appliance‘s air inlet.

♦ Wrap the threads on the connector nipple

with the teﬂon tape supplied.

♦ Screw the connector nipple

into the air inlet.

PDWS 125 A1

GB

│

11 ■

Operation

Operating a compressed air tool

NOTE

►

In order to achieve the full power available

from your compressed air tool, always

use compressed air hoses with an internal

diameter of at least 9 mm. A lower internal

diameter can considerably reduce the power.

CAUTION!

► Do not use a compressed air line that con-

tains any water condensation.

► The tool must be suﬃciently supplied with

pneumatic oil to ensure long service life. This

can take place as follows:

– Use oiled compressed air by ﬁtting a mist

lubricator.

– Without a mist lubricator: add oil manu-

ally through the compressed air connec-

tion

every day. Approx. 3-5 drops

of pneumatic oil for every 15 operating

minutes during continuous use.

► If the tool has been out of operation for sev-

eral days, add around 5 drops of pneumatic

oil manually through the compressed air

connection .

► Allow the tool to run at idling speed for a

short time.

► Always guide the machine using both hands.

► Switch on ﬁrst, then apply the accessory tool

to the workpiece.

► After switching oﬀ, only put the machine down

once the motor has come to a standstill.

♦ 1.) Attach a suitable accessory tool.

♦ 2.) Adjust the operating pressure (measured

at the air intake when the compressed air

tool has been switched on). Please refer to

the section entitled "Technical data" for the

maximum permissible operating pressure

♦ 3.) Connect the compressed air tool to the com-

pressed air supply.

♦ 4.) Switching on: Push the safety lock-out

towards and press the ON/OFF switch .

♦ 5.) Switching oﬀ: Release the ON/OFF switch

.

Working procedures

Sanding:

♦ Press the machine against the workpiece moder-

ately and move it backwards and forwards over

the surface so that the workpiece surface does

not become too hot.

Rough grinding:

♦ Work using an angle of incidence of between

30° and 40° for good working results.

NOTE

► Never use cutting discs for rough grinding.

Abrasive cutting:

♦ Always work against abrasive cutting (see Fig-

ure 3). Otherwise there is a risk that the ma-

chine can jump out of the cut in an uncontrolled

manner. Work using moderate forward speed

appropriate to the material being processed.

Do not tilt, do not press, do not oscillate.

Fig. 3

NOTE

►

Never use rough grinding discs for cutting.

PDWS 125 A1

■ 12

│

GB

Maintenance and cleaning

WARNING! RISK OF INJURY!

Disconnect the appliance from the

compressed air supply.

CAUTION!

► Any service or repair work over and above

that described in this section may only be

carried out by specialists.

♦ Maintain the compressor tool regularly to ensure

safe operation.

♦ Check bolted connections for a tight ﬁt, retighten

if necessary.

♦ Clean the ﬁlter in the compressed air connec-

tion

at least once a week.

♦ We recommend ﬁtting a pressure reducer with

a water separator and an oiler in front of the

compressed air tool.

♦ If there is increased oil or air discharge, check

the compressed air tool and have it serviced if

necessary.

♦ Check the rotation speed regularly and after

every use, and carry out a simple check of the

vibration level.

♦ Regularly check the spindle

, threads and

clamping devices for wear and tolerances for

accommodating accessory tools.

♦ Avoid contact with hazardous substances which

have accumulated on the tool. Wear suitable

personal safety equipment and remove any

hazardous substances using suitable measures

before servicing.

WARNING!

► Have your appliance repaired by the service

centre or a qualiﬁed specialist and only

using genuine replacement parts. This will

ensure that the safety of the appliance is

maintained.

Disposal

The packaging consists of environmentally

friendly material. It can be disposed of in

the local recycling containers.

Do not dispose of the appliance in the normal

domestic waste!

Your local community or municipal authorities can

provide information on how to dispose of the worn-

out appliance.

Warranty

This appliance is provided with a 3-year

warranty valid from the date of purchase.

The appliance has been manufactured with

care and inspected meticulously prior to de-

livery. Please retain your receipt as proof of

purchase. In the event of a warranty claim,

please contact your Customer Service unit by

telephone. This is the only way to guarantee

free return of your goods.

The warranty only covers claims for material and

manufacturing defects, not for damage sustained

during carriage, components subject to wear and

tear or damage to fragile components such as

switches or batteries. This appliance is intended

solely for private use and not for commercial pur-

poses. The warranty shall be deemed void in cases

of misuse or improper handling, use of force and

modiﬁcations/repairs which have not been carried

out by one of our authorised Service centres. Your

statutory rights are not restricted by this warranty.

The warranty period is not prolonged by repairs

eﬀected under the warranty. This also applies to

replaced and repaired components. Any damage

and defects present at the time of purchase must be

reported immediately after unpacking, but no later

than two days after the date of purchase. Repairs

carried out after expiry of the warranty period shall

be subject to charge.

PDWS 125 A1

GB

│

13 ■

Service

Service Great Britain

Tel.: 0871 5000 720 (£ 0.10/Min.)

E-Mail: [email protected]

IAN 276009

Importer

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

GERMANY

www.kompernass.com

Translation of the original

Conformity Declaration

We, KOMPERNASS HANDELS GMBH, docu-

ments oﬃcer: Mr. Semi Uguzlu, BURGSTR. 21,

44867 BOCHUM, GERMANY, hereby declare that

this product complies with the following standards,

normative documents and EC directives:

Machinery Directive

(2006/42/EC)

Applied harmonised standards:

EN ISO 11148-7: 2012

Type designation of machine:

Air angle grinder PDWS 125 A1

Year of manufacture: 06 - 2016

Serial number: IAN 276009

Bochum, 27.01.2016

Semi Uguzlu

- Quality Manager -

The right to eﬀect technical changes in the context

of further development is reserved.

■ 14

│

GB

PDWS 125 A1

HU

│

15 ■

Tartalomjegyzék

Bevezető .......................................................16

Rendeltetésszerű használat ...................................................16

Felszereltség ............................................................... 16

A csomag tartalma ..........................................................17

Műszaki adatok ............................................................17

Általános biztonsági szabályok ....................................17

Kirepülő alkatrészek miatti veszélyek ............................................17

Befogásveszély ............................................................. 18

Veszélyek üzemelés során ....................................................18

Ismétlődő mozgások miatti veszélyek ...........................................19

Tartozékok miatti veszélyek ...................................................19

Munkahelyi veszélyek ....................................................... 19

Por és gőzök miatti veszélyek .................................................. 20

Zajhatás miatti veszélyek ..................................................... 20

Rezgések miatti veszélyek .................................................... 21

Pneumatikus gépekre vonatkozó további biztonsági utasítások ........................ 21

Csiszolással és vágással kapcsolatos különleges biztonsági utasítások ................. 21

Vágókorongos vágásra vonatkozó további biztonsági utasítások ...................... 22

Visszaütés és megfelelő biztonsági utasítások ..................................... 22

Üzembe helyezés ................................................23

Pótmarkolat felhelyezése .....................................................23

Védőburkolat felhelyezése .................................................... 23

Csiszolókorong felhelyezése ..................................................24

Csatlakoztatható csonk felszerelése ............................................. 24

Használat .................................................................25

Munkavégzésre vonatkozó tudnivalók ........................................... 25

Karbantartás és tisztítás ..........................................26

Ártalmatlanítás ..................................................26

Garancia .......................................................26

Szerviz .........................................................27

Gyártja ........................................................27

Az eredeti megfelelőségi nyilatkozat fordítása .......................27

PDWS 125 A1

■ 16

│

HU

PNEUMATIKUS SAROKCSI-

SZOLÓ PDWS 125 A1

Bevezető

Gratulálunk új készüléke megvásárlásához. Vásár-

lásával kiváló minőségű termék mellett döntött.

A használati útmutató a termék része. Fontos tud-

nivalókat tartalmaz a biztonságra, használatra és

ártalmatlanításra vonatkozóan. A termék haszná-

lata előtt ismerkedjen meg valamennyi használati

és biztonsági utasítással. Csak a leírtak szerint és

a megadott célokra használja a készüléket. Ha

a készüléket harmadik személynek továbbadja,

akkor adja át a készülékhez tartozó valamennyi

dokumentumot is.

Rendeltetésszerű használat

A pneumatikus kéziszerszám fémek és hasonló

anyagok víz használata nélkül történő csiszolására

és vágására készült. Minden egyéb felhasználási

mód vagy a gép módosítása rendeltetésellenesnek

minősül és jelentős balesetveszélyt rejt magában.

A gép nem ipari használatra készült.

A szimbólumok magyarázata:

WARNING!

Üzembe helyezés előtt olvassa el

a használati útmutatót.

Viseljen védőszemüveget!

Forgásirány

Naponta olajozza meg!

P03/2016 Gyártás dátuma

V03/2019 Lejárat dátuma

Üzembe helyezés előtt olvassa

el az eredeti használati útmutatót

és a biztonsági utasításokat.

Viseljen hallásvédőt!

Viseljen biztonsági lábbelit!

Viseljen védőkesztyűt!

Viseljen porvédő maszkot!

Nem használható nedves

csiszoláshoz

A sérült vágó- vagy nagyoló-

korongok használata veszélyes

és súlyos sérüléseket okozhat!

Fémek csiszolására tervezték

Korong átmérője

Felszereltség

Sűrítettlevegő-csatlakozó szűrővel

Csatlakoztatható csonk 1/4“

BE/KI kapcsoló

Kapcsolózár

Védőburkolat

Orsó

Pótmarkolat

Hátoldali befogóperem

Csiszolókorong

Elülső perem

Villáskulcs

Kétlyukú kulcs

Olajtartály

Teﬂonszalag

Imbuszkulcs

PDWS 125 A1

HU

│

17 ■

A csomag tartalma

1 pneumatikus sarokcsiszoló PDWS 125 A1

1 pótmarkolat

1 csiszolókorong (Ø125mm)

1 kétlyukú kulcs

1 villáskulcs

1 imbuszkulcs

1m PTFE szalag

1 csatlakoztatható csonk (1/4“)

1 olajtartály

1 használati útmutató

Műszaki adatok

Névleges fordulatszám: 10000 min

-1

Névleges levegőnyomás: max. 6,3 bar

Korongméret: Ø 125 mm

Menetes befogó: M14

Csatlakoztatható csonk: 1/4“

Tömeg (pótmarkolattal): kb. 1,72 kg

Zajkibocsátási érték:

A zaj mérési értéke az ISO 15744 alapján

meghatározva:

Hangnyomásszint: L

pA

= 90,2 dB (A)

Bizonytalansági érték: K

pA

= 3 dB (A)

Hangerőszint: L

WA

= 101,2 dB (A)

Bizonytalansági érték: K

WA

= 3 dB (A)

Rezgés-kibocsátási érték:

Az együttes rezgési érték az ISO 28927-1 és az

EN 12096 szerint meghatározva:

a

h

= 2,44 m/s

2

Bizonytalansági érték K = 1,5 m/s

2

WARNING!

Általános biztonsági

szabályok

FIGYELMEZTETÉS!

► Többszörös veszélyeztetésnél:

A csiszolóstiftes csiszológép beállítása, üze-

me, javítása, karbantartása és tartozékainak

cseréje, illetve a gép közelében történő mun-

kavégzés előtt el kell olvasni és meg kell érteni

a biztonsági utasításokat. Ellenkező esetben a

gép súlyos testi sérüléseket okozhat.

■ A csiszolóeszközzel felszerelt csiszológépet

kizárólag megfelelően képzett és kioktatott

kezelő személyek igazíthatják be, állíthatják be

vagy használhatják.

■ A gépet nem szabad megváltoztatni. A módo-

sítások csökkenthetik a biztonsági intézkedések

hatásosságát és fokozhatják a kezelőszemély-

zetet fenyegető kockázatokat.

■ A biztonsági utasításokat őrizze meg — adja

tovább a kezelő személynek.

■ Soha ne használjon sérült csiszolóeszközzel

felszerelt csiszológépet.

Kirepülő alkatrészek miatti veszélyek

■ A munkadarab, a tartozékok, vagy a gépszer-

szám törése esetén nagy sebességgel alkatrészek

repülhetnek ki a gépből.

■ A csiszolóeszközzel felszerelt csiszológép

működése során mindig használjon ütésbiztos

szemvédőt. A szükséges védelem mértékét

minden egyes használat során külön kell mér-

legelni.

■ Ellenőrizni kell a munkadarab biztos rögzítését.

■ Ellenőrizni kell, hogy a csiszolóeszköz stabilan

fel van-e rögzítve a csiszolóeszközös csiszo-

lógépre.

Stránka sa načítava...

Parkside PDWS 125 A1 Operating Instructions Manual

Parkside PDWS 125 A1 Operating Instructions Manual

v iných jazykoch

Súvisiace články

Ostatné dokumenty