Parkside PWS 230 C3 Translation Of The Original Instructions

IAN 280715

ANGLE GRINDER PWS 230 C3

ANGLE GRINDER

Translation of the original instructions

SAROKCSISZOLÓ

Az originál használati utasítás fordítása

UHLOVÁ BRÚSKA

Preklad originálneho návodu na obsluhu

ÚHLOVÁ BRUSKA

Překlad originálního provozního návodu

WINKELSCHLEIFER

Originalbetriebsanleitung

KOTNI BRUSILNIK

Prevod originalnega navodila za uporabo

GB Translation of the original instructions Page 1

HU Az originál használati utasítás fordítása Oldal 15

SI Prevod originalnega navodila za uporabo Stran 31

CZ Překlad originálního provozního návodu Strana 45

SK Preklad originálneho návodu na obsluhu Strana 59

DE / AT / CH Originalbetriebsanleitung Seite 73

Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the

device.

Olvasás előtt kattintson az ábrákat tartalmazó mindkét oldalra és végezetül ismerje meg a készülék

mindegyik funkcióját.

Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.

Před čtením si odklopte obě dvě strany s obrázky a potom se seznamte se všemi funkcemi přístroje.

Pred čítaním si odklopte obidve strany s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich anschließend

mit allen Funktionen des Gerätes vertraut.

B

A

DC

E





I

0

PWS 230 C3

GB │ 1 ■

Contents

Introduction ......................................................2

Intended use ................................................................ 2

Features ................................................................... 2

Package contents ............................................................ 2

Technical data .............................................................. 2

General Power Tool Safety Warnings ................................3

1. Work area safety .......................................................... 3

2. Electrical safety ........................................................... 3

3. Personal safety ............................................................ 4

4. Power tool use and care .................................................... 4

5. Service .................................................................. 5

Safety instructions for all applications ............................................ 5

Kickback and corresponding safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Special safety instructions for grinding and abrasive cutting ........................... 7

Additional special safety instructions for abrasive cutting ............................. 7

Permissible accessories ........................................................ 8

Storage and handling of the recommended accessory tools ........................... 8

Working procedures .......................................................... 9

Use ............................................................10

Fitting the blade guard with quick release ........................................10

Fitting the additional handle ...................................................11

Fitting/changing the roughing/ cutting disc .......................................11

Switching on and oﬀ ........................................................12

Turning the appliance handle ..................................................12

Maintenance and cleaning .........................................12

Disposal ........................................................13

Kompernass Handels GmbH warranty ..............................13

Service .........................................................14

Importer .......................................................14

Translation of the original Conformity Declaration .....................14

PWS 230 C3

■ 2 │ GB

ANGLE GRINDER PWS 230 C3

Introduction

Congratulations on the purchase of your new appli-

ance. You have chosen a high-quality product. The

operating instructions are part of this product. They

contain important information about safety, usage

and disposal. Before using the product, please

familiarise yourself with all operating and safety

instructions. Use the product only as described and

for the range of applications speciﬁed. Please also

pass these operating instructions on to any future

owner.

Intended use

The appliance is intended for the cutting and

rough cutting of metal materials without the use of

water. Any other usage of or modiﬁcation to the

appliance is deemed to be improper and carries a

signiﬁcant risk of accidents. The manufacturer ac-

cepts no responsibility for damage(s) resulting from

improper usage. The appliance is not intended for

commercial use.

Features

Appliance handle (rotatable)

ON/OFF switch

Safety lock-out

Release button

Cover for carbon brushes

Additional handle

Blade guard

Clamping lever

Coding pin

Fine adjustment screw

Spindle locking button

Screw thread (3 x) for the additional handle

Clamping nut (see ﬁg. C)

Attachment spindle (see ﬁg. C)

Attachment ﬂange (see ﬁg. C)

Coding groove (see ﬁg. C)

Two-hole mounting spanner (see ﬁg. D)

Package contents

1 angle grinder PWS 230 C3

1 additional handle

1 blade guard

1 two-hole mounting spanner

1 operating manual

Technical data

Rated voltage: 230 V ∼, 50 Hz

(AC)

Rated power

consumption: 2000 W

Rated speed: n 6500 rpm

Disc width: Ø 230 mm

Thread size: M14

Protection class: II /

(double insulation)

Noise and vibration data:

Noise measurement value determined in accor-

dance with EN 60745. The A-rated noise level of

the power tool is typically as follows:

Noise emission value:

Sound pressure level: L

PA

= 94 dB(A)

Uncertainty: K= 3 dB

Sound power level: L

WA

= 105 dB(A)

Uncertainty: K= 3 dB

Wear hearing protection!

Total vibration value:

Surface sanding: A

h, AG

= 16.4m/s

2

Uncertainty: K = 1.5 m/s

2

PWS 230 C3

GB │ 3 ■

NOTE

► The vibration level speciﬁed in these instruc-

tions has been measured in accordance with

a standardised measuring procedure and

can be used for equipment comparisons. The

speciﬁed vibration emission value can also

be used to make an initial exposure estimate.

WARNING!

► The vibration level will vary according to the

use of the power tool and may sometimes

be higher than the value speciﬁed in these

instructions. Regular use of the power tool in

this way may cause the user to underestimate

the vibration. Try to keep the vibration loads

as low as possible. Measures to reduce the

vibration load are, e.g. wearing gloves and

limiting the working time. Wherein all states

of operation must be included (e.g. times

when the power tool is switched oﬀ and times

where the power tool is switched on but run-

ning without load).

General Power Tool

Safety Warnings

WARNING!

► Read all safety warnings and all instructions.

Failure to follow the warnings and instruc-

tions may result in electric shock, ﬁre and/or

serious injury.

Save all warnings and instructions for future

reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-

operated (cordless) power tool.

1. Work area safety

a) Keep work area clean and well lit. Cluttered

or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of ﬂam-

mable liquids, gases or dust. Power tools cre-

ate sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

2. Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools. Unmodiﬁed plugs

and matching outlets will reduce risk of electric

shock.

b)

Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of elec-

tric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entan-

gled cords increase the risk of electric shock.

e) When operating a power tool outdoors, only

use an extension cable suitable for outdoor

use. Use of a cord suitable for outdoor use

reduces the risk of electric shock.

PWS 230 C3

■ 4 │ GB

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD

reduces the risk of electric shock.

3. Personal safety

a) Stay alert, watch what you are doing and

use common sense when operating a power

tool. Do not use a power tool while you are

tired or under the inﬂuence of drugs, alcohol

or medication. A moment of inattention while

operating power tools may result in serious

personal injury.

b) Use personal protective equipment. Always

wear eye protection. Protective equipment

such as dust mask, non-skid safety shoes, hard

hat, or hearing protection used for appropriate

conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools

with your ﬁnger on the switch or energising

power tools that have the switch on invites ac-

cidents.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool

may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used.

Use of dust collection can reduce dust-related

hazards.

4. Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at

the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and oﬀ. Any power tool that can-

not be controlled with the switch is dangerous

and must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing ac-

cessories, or storing power tools. Such preven-

tive safety measures reduce the risk of starting

the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalign-

ment or binding of moving parts, breakage of

parts and any other condition that may aﬀect

the power tools operation. If damaged, have

the power tool repaired before use. Many ac-

cidents are caused by poorly maintained power

tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

g)

Use the power tool, accessories and tool

bits, etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed. Use of the

power tool for operations diﬀerent from those

intended could result in a hazardous situation.

PWS 230 C3

GB │ 5 ■

5. Service

a) Have your power tool serviced by a qualiﬁed

repair person using only identical replace-

ment parts. This will ensure that the safety of

the power tool is maintained.

b) Always arrange for the replacement of the

plug or the power cord to be carried out by

the manufacturer of the appliance or by his

approved customer services. This will ensure

that the safety of the power tool is maintained.

Safety instructions for all

applications

Special safety instructions for grinding and

abrasive cutting:

a) This power tool is to be used as a grinder and

abrasive cutting appliance. Please follow all

safety instructions, instructions, diagrams and

data that you receive with the appliance. If

you do not observe the following instructions,

this can lead to an electrical shock, ﬁre and/or

serious injuries.

b) This power tool is not suitable for sandpaper

sanding, working with a steel brush or bur-

nishing. Using the power tool for applications

for which it is not designed can lead to hazards

and injuries.

c) Do not use any accessories that have not

been speciﬁcally provided or recommended

by the manufacturer for this power tool. Just

because you can attach the accessories to your

power tool does not guarantee they are safe to

use.

d) The maximum speed of the accessory tool

used must be at least as high as the maximum

speed speciﬁed for the power tool. Acces-

sories that rotate faster than the permissible rate

can break and throw pieces into the air.

e) The external diameter and thickness of the

accessory tool used must comply with the di-

mensions of the power tool. Incorrectly dimen-

sioned accessory tools cannot be suﬃciently

shielded or controlled.

f) Attachment tools with a thread insert must

match the thread of the grinding spindle ex-

actly. For attachment tools that are mounted

using a ﬂange, the diameter of the hole on

the attachment tool must correspond to the

width of the ﬁtment on the ﬂange. Accessory

tools that do not exactly ﬁt on the grinding

spindle rotate unevenly, vibrate severely and

can lead to a loss of control.

g) Never use damaged accessory tools. Check

accessory tools such as grinding discs before

each use for chips or cracks, grinding plates

for cracks, wearing or excessive wear and

tear and wire brushes for loose or broken

wires. If the power tool or the accessory tool

in use is dropped, check to see if it is dam-

aged or use an undamaged accessory tool.

When you have checked and inserted the

accessory tool, ensure that you and any other

persons in the vicinity remain outside of the

level of the rotating accessory tool and allow

the tool to rotate at maximum speed for one

minute. Damaged accessories usually break

during the test period.

h) Wear personal protective equipment. De-

pending on the application, ensure that you

use full face protection, eye protection or

goggles. Use a dust mask, hearing protec-

tion, protective gloves or special apron that

protect you from grindings and material

particles as required. Protected your eyes from

ﬂying debris that may be created during certain

applications. Dust or ﬁlter masks must be used

to ﬁlter any dust created by the application. If

you are exposed to loud noise for any length of

time, you may suﬀer hearing loss.

i) Ensure that other people remain at a safe dis-

tance to your workspace. Anyone who enters

the workspace must wear personal protective

equipment. Fragments of the workpiece or bro-

ken accessory tools can ﬂy oﬀ and cause injury

– even outside the immediate working area.

PWS 230 C3

■ 6 │ GB

j) Hold the power tool only by the insulated

handles when you are carrying out work

in which the accessory tool may come into

contact with concealed power cables or the

tool’s own power cord. Contact with a live

cable can also make metal parts of the appli-

ance live and could result in an electric shock.

k) Keep the power cord away from any rotating

accessories. If you lose control of the appli-

ance, the cord may get caught or cut and your

hand or arm could get caught in the rotating

accessory tool.

l) Never put the power tool down until the ac-

cessory tool being used has come to a com-

plete standstill. The rotating accessory tool can

come into contact with the surface and cause

you to lose control of the power tool.

m) Do not leave the power tool running whilst

carrying it. Accidental contact between your

clothing and the rotating accessory tool could

lead to physical injury.

n) Clean the ventilation slits of your power tool

regularly. The engine fan draws dust into the

housing and a strong accumulation of metal

dust can cause electrical hazards.

o) Never use the power tool in the vicinity of

inﬂammable materials. Sparks can ignite these

materials.

p) Do not use any accessory tools which require

liquid coolant. The use of water or other liquid

coolants may lead to electric shock.

Kickback and corresponding safety

instructions

Kickback is a sudden reaction caused when a

rotating accessory tool, e.g. grinding disc, grinding

plate, wire brush, etc., catches or jams. Catching or

jamming leads to an abrupt stop of the rotating ac-

cessory tool. If this happens, an uncontrolled pow-

er tool turns rapidly against the direction of rotation

of the accessory tool caught in the blockage.

If, for example, a grinding disc catches or jams in a

workpiece, the edge of the grinding disc projecting

into the workpiece can get caught and break oﬀ

the grinding disc or cause a kickback. The grinding

disc can then ﬂy in the direction of the operator or

away from him, depending on the direction of rota-

tion of the disc at the blockage. This can also break

grinding discs.

A kickback is caused by incorrect use or misuse

of the power tool. This can be avoided by taking

proper precautions as described below.

a) Hold the power tool ﬁrmly in both hands and

position your body and arms so they can

absorb the force of a kickback. Always use

the additional handle, if available, so that

you have the maximum possible control over

the kickback force or reaction forces at full

speed. By taking adequate precautions, the

operator can stay in control of the kickback and

reaction torques.

b) Never hold your hand close to a rotating ac-

cessory tool. The accessory tool could hit your

hand in the event of a kickback.

c) Avoid having any part of your body in the

region in which the power tool is likely to

move in event of a kickback. The kickback will

force the power tool in the opposite direction to

the direction of rotation of the grinding disc at

the blockage.

d) Take special care when working near cor-

ners, sharp edges, etc. Avoid allowing the

accessory tool to bounce back from the work-

piece or jam. The rotating accessory tool is

more likely to jam in corners or sharp edges or

if it rebounds oﬀ them. This can cause a loss of

control or kickback.

e) Do not use chains or toothed saw blades.

Such accessories often cause a kickback or loss

of control over the power tool.

PWS 230 C3

GB │ 7 ■

Special safety instructions for

grinding and abrasive cutting

a) Use only the grinding accessories approved

for your power tool and the appropriate

blade guard for these grinding tools. Grind-

ing tools that are not designed for the power

tool cannot be suﬃciently shielded and are

unsafe.

b) Oﬀset grinding discs must be ﬁtted so that the

grinding surface does not protrude over the

level of the blade guard edge. An improperly

ﬁtted grinding disc which protrudes over the

level of the blade guard edge cannot be prop-

erly guarded.

c) The blade guard must be securely mounted

on the power tool and adjusted to ensure

maximum safety so that the smallest possible

amount of the grinding tool is open to the op-

erator. The blade guard is designed to protect

the operator from fragments, accidental contact

with the grinding tool and sparks that could

ignite clothing.

d) Grinding tools should only be used for the

recommended applications.

For example: Never grind with the side

surface of a cutting disc. Cutting discs are de-

signed to remove material with the edge of the

disc. Any lateral application of force on these

grinding tools can lead to breakage.

e) Always use an undamaged clamping ﬂange

of the correct size and shape for the selected

grinding disc. Suitable ﬂanges support the

grinding disc and reduce the risk of disc break-

age. Flanges for cutting discs can be diﬀerent to

ﬂanges for other grinding discs.

f) Do not use worn grinding discs from larger

power tools. Grinding discs for larger power

tools are not designed for the higher rotational

speeds of smaller power tools and can break.

Additional special safety instructions

for abrasive cutting

a) Avoid causing blockages to the cutting disc

or high contact pressure. Do not make any

excessively deep cuts. Overloading the cutting

disc increases the stress and likelihood of tilting

or jamming and thus the possibility of kickback

or breakage of the grinding tool.

b) Avoid the area in front of and behind the

rotating cutting disc. When you move the cut-

ting disc away from yourself in the workpiece,

it is possible, in the event of a kickback, that the

power tool along with the rotating disc might be

thrown out directly towards you.

b) If the cutting disc jams or you stop working,

switch the tool oﬀ and hold it steadily in

the workpiece until the disc has completely

stopped turning. Never attempt to pull a ro-

tating cutting disc out of a cut. This could lead

to kickback. Identify and remove the cause of

the jam.

d) Do not switch the power tool back on while

it is located in the workpiece. Allow the cut-

ting disc to reach its full speed before you

carefully continue the cut. Otherwise, the disc

can jam, jump out of the workpiece or cause

kickback.

e) Support boards or large workpieces to re-

duce the risk of the cutting disc jamming and

causing a kickback. Large workpieces can

bend under their own weight. The workpiece

must be supported on both sides of the disc:

both in the vicinity of the cutting disc and also

at the edge.

f) Be particularly careful when making "pocket

cuts" into existing walls or other obscured

areas. The inserted cutting disc may cut into

gas or water pipes, electrical wiring or other

objects that can cause kickback.

PWS 230 C3

■ 8 │ GB

Permissible accessories

Max.

diameter

Ø (mm)

Max.

thick-

ness

(mm)

Thread

size (mm)

Speed

(rpm)

Circum-

ferential

speed

(m/s)

Tool Blade guard

Cutting disc

230 3 M14 6500 80

Two-hole

mounting

spanner

Yes

Roughing disc

230 6 M14 6500 80

Two-hole

mounting

spanner

Yes

Storage and handling of the recommended accessory tools

■ Grinding tools are to be treated with care and transported carefully.

■ Grinding tools should be stored in such a way that they are not exposed to mechanical damage or

environmental inﬂuences (e.g. moisture).

PWS 230 C3

GB │ 9 ■

Working procedures

NOTE

► Grinding tools should only be used for the

recommended applications. Otherwise, they

can break, be damaged or cause injuries.

Rough grinding:

Never use cutting discs for rough

grinding!

■ Move the angle grinder with moderate pres-

sure back and forth over the workpiece.

■ For soft material, move the rough grinding

disc at a shallow angle over the workpiece;

for hard material at a slightly steeper angle.

Abrasive cutting:

Never use rough grinding discs for

cutting!

■ Use only tested ﬁbre-reinforced cutting or

grinding discs that are approved for a circum-

ferential speed of not less than 80 m/s.

CAUTION!

The grinder continues running after being turned

oﬀ. Do not try to brake it by applying lateral

counterpressure.

■ Secure the workpiece! Use clamps/a vice to

hold the workpiece ﬁrmly in place. This is much

safer than simply holding it in your hand.

■ Always switch oﬀ the appliance before put-

ting it away and wait for the appliance to

come to a complete standstill.

■ Release the ON/OFF switch immediately in

the event of a power failure or when the plug

is pulled out. Move it into the OFF position. This

prevents an uncontrolled restart.

■ Use the appliance only for dry cutting or

sanding.

■ The additional handle

must be mounted on

the appliance for all work.

■ Materials containing asbestos may not be

processed. Asbestos is a known carcinogen.

Tip! This symbol indicates proper

behaviour.

HAZARD! ALWAYS GUIDE THE

APPLIANCE THROUGH THE WORK-

PIECE IN REVERSE ROTATION.

► In the opposite direction there is a risk of

kickback. The appliance can be pushed out

of the cut.

■ Always switch the appliance on before apply-

ing it to the workpiece. After completing the

task, lift the appliance from the workpiece and

then switch it oﬀ.

■ Always hold the appliance ﬁrmly with two

hands while working. Ensure that your stance

is secure and stable.

■ For an optimum grinding eﬀect, move the ap-

pliance evenly at an angle of 15° to 30° (be-

tween grinding disc and workpiece) backwards

and forwards.

PWS 230 C3

■ 10 │ GB

■ When working on angled surfaces, do not

exert great force on the workpiece. If the

rotational speed drops signiﬁcantly, you must

reduce the pressure exerted to allow safe and

eﬀective working. If the appliance suddenly

brakes completely or jams, it must be switched

oﬀ immediately.

■ Cutting: Work at a moderate feed rate and

do not tilt the cutting disc.

■ Roughing and cutting discs become very

hot – let them cool down completely before

touching them.

■ Never use the appliance for purposes other

than the ones for which it was designed.

■ Always make sure that the appliance is

turned oﬀ before plugging it into the wall

socket.

■ In case of danger, remove the plug from the

socket immediately. Ensure that the appliance

and the power socket are easily and quickly

accessible in the event of an emergency.

■ Always remove the plug from the power

socket during work breaks, when adjusting

the appliance and when it is no longer in use.

The appliance must be kept clean, dry and free

of oil and grease at all times.

■ Remain alert at all times! Always pay atten-

tion to what you are doing and act with com-

mon sense. Do not use the appliance if you are

distracted or feeling unwell.

WARNING!

Always wear safety googles.

WARNING!

Always wear a dust mask!

Use

Fitting the blade guard with quick

release

WARNING! RISK OF INJURY

► Always remove the plug from the power

socket before working on the appliance.

RISK OF INJURY

► Always use the angle grinder with the blade

guard

. The blade guard should be ﬁtted

securely. Set it so that the highest possible

degree of safety is achieved, i.e. the smallest

possible part of the grinding disc is open to

the operator. The blade guard is designed

to protect the operator from fragments and

accidental contact with the grinding tool.

RISK OF INJURY

► Make sure that the blade guard

is ﬁtted

at least at the same angle as the additional

handle

(see ﬁg. B). Otherwise, you could

cut injure yourself on the roughing disc or

cutting disc.

♦ Open the clamping lever

.

♦ Place the blade guard

with the coding pin

in the coding groove .

♦ Turn the blade guard

to the required position

(working position). The closed side of the blade

guard must always be toward the operator.

♦ Close the clamping lever

to clamp the

blade guard into position. If necessary, the

clamping force of the lock can be changed by

loosening or tightening the adjusting screw .

Ensure that the blade guard sits ﬁrmly on the

neck of the spindle.

PWS 230 C3

GB │ 11 ■

Fitting the additional handle

CAUTION!

► For safety reasons, this appliance may only

be used with the additional handle

.

Failure to do this can lead to serious injury.

The additional handle

can be screwed

onto the left or the right depending on the job

at hand.

Fitting/changing the roughing/

cutting disc

Always wear protective gloves when chang-

ing cutting/rough grinding discs. Roughing and

cutting discs become very hot. Allow them to cool

down completely before touching them.

Pay attention to the dimensions of the roughing/

cutting disc. The diameter of the whole must ﬁt the

mounting ﬂange without any play. Do not use a

reducer or adapter.

■ Check the roughing/cutting disc. It should not

be damaged or damp, and it should have no

cracks. Otherwise, it could break during use

and cause injuries.

NOTE

► Use only discs which are free of dirt.

■ Use only grinding discs whose permissible

speed rating is at least as high as that on the

type plate on the power tool.

■ RISK OF INJURY! Press the spindle locking

button

only when the mounting spindle is

at a complete standstill.

♦ Press the spindle locking button to lock the

motor.

♦ Undo the clamping nut

using the two-hole

mounting spanner (see ﬁg B).

♦ Place the rough grinding or cutting disc with the

label side towards the appliance on the mount-

ing ﬂange

.

♦ Then replace the clamping nut with the raised

side facing up on the mounting spindle .

With thin grinding discs (see ﬁg. 1):

♦ The collar of the clamping nut

faces upwards

so that a thin grinding disc can be ﬁtted safely.

12

≤ 3,2 mm

Fig. 1

♦ Press the spindle locking button

to lock the

motor.

♦ Tighten the clamping nut

using the two-hole

mounting spanner .

With thick grinding discs (see ﬁg. 2):

> 3,2 mm

Fig. 2

The collar of the clamping nut

faces upwards so

that the clamping nut can be ﬁtted securely onto

the mounting spindle .

♦ Lock the mounting spindle

.

♦ Tighten the clamping nut

in a clockwise di-

rection using the two-hole mounting spanner .

NOTE

► If the disc does not turn smoothly or vibrates

after the change, the disc must be replaced

immediately.

♦ For safety's sake run the appliance at maximum

speed for 60 seconds after every disc change.

Be aware of unusual noises and sparks.

PWS 230 C3

■ 12 │ GB

♦ Check whether all the fastening elements are

correctly ﬁtted.

♦ Make sure that the arrow showing the direction

of rotation (if any) on the cutting or rough grind-

ing discs (including diamond cutting discs) and

the direction of rotation of the appliance (arrow

showing the direction of rotation on the head)

match.

Switching on and oﬀ

Check the inserted tool before use. It must be

properly installed, may not be damaged or damp,

should have no cracks and turn freely. Carry out

a 60 second test run. Do not use non-circular or

vibrating tools. Be aware of unusual noises and

sparks. Check whether all the fastening elements

are correctly installed.

NOTE

► Always switch on the angle grinder before

making contact with the material, then apply

it to the workpiece.

Switching on:

♦ Press the safety lock-out

(see ﬁg. E).

♦ Then press the ON/OFF switch

.

Switching oﬀ:

♦ Let go of the ON/OFF switch

.

Turning the appliance handle

■ The handle can be turned by 90° to the

right or left (see ﬁg. A).

■ This allows the ON/OFF switch

to be moved

to the most suitable position depending on the

working conditions.

♦ Press the release button and turn the appli-

ance handle to the right or left.

♦ Allow the appliance handle

to click into

place.

Maintenance and cleaning

WARNING! RISK OF INJURY! Switch

the appliance oﬀ and remove the

power plug before starting any

work on the appliance.

■ Do not use any sharp objects to clean the

appliance. Never permit liquids to enter

inside the appliance. Otherwise the appliance

could be damaged.

■ The carbon brushes should only be replaced

by the service centre or an authorised specialist

workshop.

Apart from this, the appliance is maintenance-

free.

■ Clean the appliance regularly, preferably im-

mediately after completion of the work.

■ Clean the housing with a dry cloth – do NOT

use petrol, solvents or cleaners which can attack

the plastic.

■ A vacuum cleaner is required for thorough

cleaning of the appliance.

■ Ventilation openings must never be obstructed.

■ Remove any sanding dust stuck to the appliance

with a brush.

NOTE

► Replacement parts not listed (such as carbon

brushes, switch) can be ordered via our

service hotline.

PWS 230 C3

GB │ 13 ■

Disposal

The packaging consists of environmentally

friendly material. It can be disposed of in

the local recycling containers.

Do not dispose of power tools in

your normal domestic waste!

European Directive 2012/19/EU requires that

worn-out power tools be collected separately and

recycled in an environmentally compatible manner.

Your local community or municipal authorities

can provide information on how to dispose of the

appliance.

Kompernass Handels GmbH

warranty

Dear Customer,

This appliance has a 3-year warranty valid from

the date of purchase. If this product has any faults,

you, the buyer, have certain statutory rights. Your

statutory rights are not restricted in any way by the

warranty described below.

Warranty conditions

The validity period of the warranty starts from the

date of purchase. Please keep your original receipt

in a safe place. This document will be required as

proof of purchase.

If any material or production fault occurs within

three years of the date of purchase of the product,

we will either repair or replace the product for you

at our discretion. This warranty service is dependent

on you presenting the defective appliance and

the proof of purchase (receipt) and a short written

description of the fault and its time of occurrence.

If the defect is covered by the warranty, your product

will either be repaired or replaced by us. The repair

or replacement of a product does not signify the

beginning of a new warranty period.

Warranty period and statutory claims for

defects

The warranty period is not prolonged by repairs

eﬀected under the warranty. This also applies to

replaced and repaired components. Any damage

and defects present at the time of purchase must

be reported immediately after unpacking. Repairs

carried out after expiry of the warranty period shall

be subject to a fee.

Scope of the warranty

This appliance has been manufactured in accordance

with strict quality guidelines and inspected meticu-

lously prior to delivery.

The warranty covers material faults or production

faults. The warranty does not extend to product parts

subject to normal wear and tear or fragile parts such

as switches, batteries, baking moulds or parts made

of glass.

The warranty does not apply if the product has been

damaged, improperly used or improperly maintained.

The directions in the operating instructions for the

product regarding proper use of the product are

to be strictly followed. Uses and actions that are

discouraged in the operating instructions or which

are warned against must be avoided.

This product is intended solely for private use and

not for commercial purposes. The warranty shall be

deemed void in cases of misuse or improper handling,

use of force and modiﬁcations/repairs which have

not been carried out by one of our authorised

Service centres.

PWS 230 C3

■ 14 │ GB

Warranty claim procedure

To ensure quick processing of your case, please

observe the following instructions:

■ Please have the till receipt and the item number

(e.g. IAN 12345) available as proof of purchase.

■ You will ﬁnd the item number on the type plate,

an engraving on the front page of the instructions

(bottom left), or as a sticker on the rear or

bottom of the appliance.

■ If functional or other defects occur, please

contact the service department listed either by

telephone or by e-mail.

■ You can return a defective product to us free of

charge to the service address that will be provided

to you. Ensure that you enclose the proof of

purchase (till receipt) and information about

what the defect is and when it occurred.

NOTE

► For Parkside and Florabest tools, please send

us only the defective item without the acces-

sories (e.g. battery, storage case, assembly

tools, etc.).

You can download these instructions

along with many other manuals,

product videos and software on

www.lidl-service.com.

Service

Service Great Britain

Tel.: 0871 5000 720 (£ 0.10/Min.)

E-Mail: [email protected]

IAN 280715

Importer

Please note that the following address is not the

service address. Please use the service address

provided in the operating instructions.

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

GERMANY

www.kompernass.com

Translation of the original

Conformity Declaration

We, KOMPERNASS HANDELS GMBH,

document oﬃcer: Mr. Semi Uguzlu, BURGSTR. 21,

44867 BOCHUM, GERMANY, hereby declare

that this product complies with the following

standards, normative documents and EC directives:

Machinery Directive

(2006/42/EC)

EMC (Electromagnetic Compatibility)

(2014/30/EU)

RoHS Directive

(2011 / 65 / EU)*

*The manufacturer bears the full responsibility for compli-

ance with this conformity declaration. The object of the

declaration described above complies with the require-

ments of the Directive 2011/65/EU of the European

Parliament and Council of 8 June 2011 on the limitations

of use of certain dangerous substances in electrical and

electronic appliances.

Applied harmonised standards:

EN 60745-1:2009/A11:2010

EN 60745-2-3:2011/A12:2014

EN 55014-1:2006/A2:2011

EN 55014-2:2015

EN 61000-3-2:2014

EN 61000-3-3:2013

Type designation of machine:

Angle grinder PWS 230 C3

Year of manufacture: 10 - 2016

Serial number: IAN 280715

Bochum, 17/10/2016

Semi Uguzlu

- Quality Manager -

We reserve the right to technical changes in the

context of further product development.

PWS 230 C3

HU │ 15 ■

Tartalomjegyzék

Bevezető .......................................................16

Rendeltetésszerű használat ...................................................16

Felszereltség ............................................................... 16

A csomag tartalma ..........................................................16

Műszaki adatok ............................................................16

Általános biztonsági utasítások elektromos kéziszerszámokhoz .........17

1. Munkahelyi biztonság .....................................................17

2. Elektromos biztonság ......................................................17

3. Személyi biztonság .......................................................18

4. Az elektromos kéziszerszám használata és kezelése .............................18

5. Szerviz .................................................................19

Valamennyi felhasználási területre vonatkozó biztonsági utasítások .................... 19

Visszaütés és megfelelő biztonsági utasítások .....................................20

Csiszolással és vágással kapcsolatos különleges biztonsági utasítások .................21

Vágókorongos vágásra vonatkozó további biztonsági utasítások ...................... 21

Engedélyezett tartozékok .....................................................22

Az ajánlott cserélhető szerszámok tárolása és kezelése .............................22

Munkavégzésre vonatkozó tudnivalók ...........................................23

Használat ......................................................24

Védőburkolat felszerelése gyorszár segítségével ...................................24

Pótmarkolat felszerelése ......................................................25

Nagyoló korong / vágókorong felszerelése / cseréje ............................... 25

Be- és kikapcsolás ..........................................................26

Készülékmarkolat elforgatása .................................................26

Karbantartás és tisztítás ..........................................26

Ártalmatlanítás ..................................................26

Jótállási tájékoztató ..............................................27

Az eredeti megfelelőségi nyilatkozat fordítása .......................29

PWS 230 C3

■ 16 │ HU

SAROKCSISZOLÓ PWS 230 C3

Bevezető

Gratulálunk új készüléke megvásárlásához.

Vásárlásával kiváló minőségű termék mellett dön-

tött. A használati útmutató a termék része. Fontos

tudnivalókat tartalmaz a biztonságra, használatra

és ártalmatlanításra vonatkozóan. A termék hasz-

nálata előtt ismerkedjen meg valamennyi kezelési

és biztonsági utasítással. Csak a leírtak szerint és a

megadott célokra használja a készüléket. A készü-

lék harmadik személynek továbbadása esetén adja

át a készülékhez tartozó valamennyi leírást is.

Rendeltetésszerű használat

A készülék fém alapanyagok víz használata nélküli

szétvágására, nagyolására szolgál. A készülék

minden más használata vagy módosítása nem

rendeltetésszerűnek minősül és jelentős balesetve-

szélyt okozhat. Nem rendeltetésszerű használatból

eredő károkért nem vállalunk felelősséget. A készü-

lék nem alkalmas ipari használatra.

Felszereltség

készülékmarkolat (forgatható)

BE/KI kapcsoló

kapcsolózár

kireteszelő gomb

szénkefe-burkolat

pótmarkolat

védőburkolat

szorítókar

reteszelő pecek

beállító csavar

orsóreteszelő gomb

menet (3 x) a pótmarkolathoz

szorítóanya (lásd a C ábrát)

befogóorsó (lásd a C ábrát)

befogókarima (lásd a C ábrát)

reteszhorony (lásd a C ábrát)

kétlyukú szerelőkulcs (lásd a D ábrát)

A csomag tartalma

1 sarokcsiszoló, PWS 230 C3

1 pótmarkolat

1 védőburkolat

1 kétlyukú szerelőkulcs

1 használati útmutató

Műszaki adatok

Névleges feszültség: 230 V ∼ 50 Hz

(váltóáram)

Névleges

teljesítményfelvétel: 2000 W

Névleges

fordulatszám: n 6500 min

-1

Korongméret: Ø 230 mm

Menetméret: M14

Védelmi osztály: II /

(dupla szigetelés)

Zaj- és rezgésinformációk:

A zaj mért értéke az EN 60745 szabványnak

megfelelően került meghatározásra. Az elektromos

kéziszerszám A-súlyozott zajszintjének jellemző

értéke:

Zajkibocsátási érték:

Hangnyomásszint: L

PA

= 94 dB (A)

Bizonytalansági érték: K = 3 dB

Hangerőszint: L

WA

= 105 dB (A)

Bizonytalansági érték: K = 3 dB

Viseljen hallásvédőt!

Rezgés összértéke:

Felületcsiszolás: a

h, AG

= 16,4 m/s

2

Bizonytalansági érték: K = 1,5 m/s

2

Stránka sa načítava ...

Parkside PWS 230 C3 Translation Of The Original Instructions

Parkside PWS 230 C3 Translation Of The Original Instructions

V iných jazykoch

Súvisiace články

Ďalšie dokumenty