Parkside PMNF 1350 B2 Translation Of The Original Instructions

IAN 280254

WALL CHASER PMNF 1350 B2

WALL CHASER

Translation of the original instructions

MAUERNUTFRÄSE

Originalbetriebsanleitung

FALHORONYMARÓ

Az originál használati utasítás fordítása

REZKALNIK ZIDNIH UTOROV

Prevod originalnega navodila za uporabo

DRÁŽKOVACÍ FRÉZA DO ZDIVA

Překlad originálního provozního návodu

DRÁŽKOVACIA FRÉZA DO MURIVA

Preklad originálneho návodu na obsluhu

GB Translation of the original instructions Page 1

HU Az originál használati utasítás fordítása Oldal 13

SI Prevod originalnega navodila za uporabo Stran 27

CZ Překlad originálního provozního návodu Strana 39

SK Preklad originálneho návodu na obsluhu Strana 51

DE / AT / CH Originalbetriebsanleitung Seite 63

Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the

device.

Olvasás előtt kattintson az ábrákat tartalmazó mindkét oldalra és végezetül ismerje meg a készülék

mindegyik funkcióját.

Pred branjem obe strani s slikami odprite navzven in se nato seznanite z vsemi funkcijami naprave.

Před čtením si odklopte obě dvě strany s obrázky a potom se seznamte se všemi funkcemi přístroje.

Pred čítaním si odklopte obidve strany s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich anschließend

mit allen Funktionen des Gerätes vertraut.





I

0

A B

C D

E

5

17

14

13

17

14

13

5

✓

✗

Ok

F

5

17

14

13



Ok

14

G

PMNF 1350 B2

GB

│

1 ■

Contents

Introduction ...........................................................2

Intended use ...................................................................... 2

Features ......................................................................... 2

Package contents .................................................................. 2

Technical data .................................................................... 2

General Power Tool Safety Warnings .....................................3

1. Work area safety ................................................................ 3

2. Electrical safety ................................................................. 3

3. Personal safety .................................................................. 3

4. Power tool use and care .......................................................... 4

5. Service ........................................................................ 4

Safety instructions for abrasive cutting appliances ......................................... 4

Further safety instructions for abrasive cutting applications .................................. 6

Supplementary notes ............................................................... 7

Original accessories/auxiliary equipment ............................................... 7

Before use ............................................................7

Setting the cut width of the diamond cutting discs ......................................... 7

Replacing the diamond cutting discs (see Figures A - F) ..................................... 8

Setting the groove depth ............................................................ 8

Attaching the dust extraction adapter .................................................. 8

Operation ............................................................8

Switching on and oﬀ ............................................................... 8

Handling the wall grinder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Maintenance and cleaning ...............................................9

Disposal ..............................................................9

Kompernass Handels GmbH warranty ...................................10

Service ..............................................................11

Importer ............................................................11

Translation of the original Conformity Declaration ..........................11

PMNF 1350 B2

■ 2

│

GB

WALL CHASER PMNF 1350 B2

Introduction

Congratulations on the purchase of your new appli-

ance. You have selected a high-quality product. The

operating instructions are part of this product. They

contain important information on safety, usage and

disposal. Before using the product, familiarise your-

self with all handling and safety guidelines. Use the

product only as described and for the range of ap-

plications speciﬁed. Please also pass these operating

instructions on to any future owner.

Intended use

The wall grinder (standard nomenclature: abrasive

cutting appliance), hereinafter referred to as the

appliance, is designed for making cuts or slits

(without the use of water) in ﬁrmly supported and

primarily mineral materials such as concrete or ma-

sonry, using the guide carriage and in combination

with an approved industrial dust extractor. Any

other usage of or modiﬁcation to the appliance

is deemed to be improper and carries the risk of

serious personal injury. Not for commercial use.

Features

ON/OFF switch

Handle

Dust extraction adapter

Union nut

Blade guard

Locking ﬂange (with thread)

Locking screw for the depth stop

Depth stop

Additional handle

Safety lock-out

Spindle lock

Roller

Reducer

Flange

Blotters

Face spanner

Hand chisel

Backing ﬂange

Package contents

1 wall chaser

2 cutting discs (pre-ﬁtted)

1 face spanner

1 dust extraction adapter (pre-ﬁtted)

1 reducer (for use with the dust extraction adapter

and a dust extractor hose of ∅ 32 mm)

1 hand chisel

1 operating manual

Technical data

Input voltage: 230 V

~

50 Hz

(alternating current)

Power consumption: 1350 W

Rated speed: n 9000 rpm

Disc sizes Ø: 125 mm

Central ﬁxing bore: 22.23 mm

Groove depth: 0–30 mm

Groove widths: min. 8mm to max. 26mm

Thread: M14

Protection class: II /

(double insulation)

Weight: approx. 4 kg

Noise and vibration data:

The noise and vibration values have been

determined in accordance with EN60745.

Sound pressure level L

pA

: 98.0 dB(A)

Uncertainty K

pA

: 3 dB

Sound power level L

WA

: 109.0 dB(A)

Uncertainty K

WA

: 3 dB

Total vibration values (vector total of three direc-

tions) determined in accordance with EN 60745.

Details of vibration values (when cutting oﬀ a

concrete plate):

Main handle: a

h

= 5.450 m/s

2

Uncertainty K = 1.5 m/s

2

Auxiliary handle: a

h

= 4.737 m/s

2

Uncertainty K = 1.5 m/s

2

PMNF 1350 B2

GB

│

3 ■

NOTE

► The vibration level speciﬁed in these instruc-

tions has been measured in accordance with

a standardised measuring procedure speciﬁed

in EN 60745 and can be used to make equip-

ment comparisons. The speciﬁed vibration

emission value can also be used to make an

initial exposure estimate.

WARNING!

► The vibration level varies in accordance with

the use of the power tool and may be higher

than the value speciﬁed in these instructions

in some cases. There is a risk of underestima-

tion of the vibration load if the power tool is

used regularly in this manner. Try to keep the

vibration loads as low as possible. Measures

to reduce the vibration load are, e.g. wearing

gloves and limiting the working time. Wherein

all states of operation must be included (e.g.

times when the power tool is switched oﬀ and

times where the power tool is switched on but

running without load).

General Power Tool

Safety Warnings

WARNING!

► Read all safety warnings and all instruc-

tions. Failure to follow the warnings and

instructions may result in electric shock, ﬁre

and/or serious injury.

Save all warnings and instructions for future

reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-op-

erated (cordless) power tool.

1. Work area safety

a) Keep work area clean and well lit. Cluttered

or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or

fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

2. Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools. Unmodiﬁed plugs

and matching outlets will reduce risk of electric

shock.

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, cookers and

refrigerators. There is an increased risk of elec-

tric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduc-

es the risk of electric shock.

3. Personal safety

a) Stay alert, watch what you are doing and

use common sense when operating a power

tool. Do not use a power tool while you are

tired or under the inﬂuence of drugs, alcohol

or medication. A moment of inattention while

operating power tools may result in serious

personal injury.

b) Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat,

or hearing protection used for appropriate

conditions will reduce personal injuries.

PMNF 1350 B2

■ 4

│

GB

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools

with your ﬁnger on the switch or energising

power tools that have the switch on invites

accidents.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool

may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jew-

ellery or long hair can be caught in moving

parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used.

Use of dust collection can reduce dust-related

hazards.

4. Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at

the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and oﬀ. Any power tool that can-

not be controlled with the switch is dangerous

and must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may aﬀect the

power tool’s operation. If damaged, have the

power tool repaired before use. Many acci-

dents are caused by poorly maintained power

tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and

the work to be performed. Use of the power

tool for operations diﬀerent from those intended

could result in a hazardous situation.

5. Service

a) Have your power tool serviced by a qualiﬁed

repair person using only identical replacement

parts. This will ensure that the safety of the

power tool is maintained.

Safety instructions for abrasive

cutting appliances

a) The blade guard, which is a part of the power

tool, must be attached securely and set in a

way that ensures maximum safety, i.e. the

smallest possible amount of the grinding tool

is exposed to the operator. Ensure that you

and anyone else in the vicinity remain outside

of the range of the rotating grinding disc. The

blade guard is designed to protect the operator

from fragments and accidental contact with the

grinding tool.

b) Use only diamond-coated cutting discs for

your power tool. Just because you can attach

the accessories to your power tool, does not

ensure they are safe to use.

c) The maximum speed of the accessory tool

used must be at least as high as the maximum

speed speciﬁed for the power tool. Accessories

which rotate faster than the maximum permissible

rate can break and throw pieces into the air.

PMNF 1350 B2

GB

│

5 ■

d) Grinding tools should only be used for the

recommended applications. For example:

Never grind with the side surface of a cutting

disc. Cutting discs are designed to remove

material with the edge of the disc. Any lateral

application of force on these grinding tools can

lead to breakage.

e) Always use an undamaged clamping ﬂange

of the correct size and shape for the selected

grinding disc. Suitable ﬂanges support the

grinding disc and reduce the risk of disc break-

age.

f) The external diameter and thickness of the

accessory tool used must comply with the

dimensions of your power tool. Incorrectly

dimensioned accessory tools cannot be suﬃ-

ciently shielded or controlled.

g) Grinding discs and ﬂanges must ﬁt precisely

onto the grinding spindle of your power tool.

Accessory tools which do not ﬁt precisely on

the grinding spindle of the power tool will rotate

unevenly, vibrate severely and can lead to a

loss of control.

h) Do not use damaged grinding discs. Check

the grinding discs before each use for chips

and cracks. If the power tool or grinding disc

is dropped, check to see if it either are dam-

aged, or use an undamaged grinding disc.

After checking and inserting the grinding

disc, ensure that you and any other people

in the vicinity remain outside of the range of

the rotating grinding disc, and allow the tool

to rotate at maximum speed for one minute.

Damaged grinding discs usually break during

this test period.

i) Wear personal protective equipment.

Depending on the application, ensure that

you use full face protection, eye protection

or goggles. If required, use a dust mask, ear

protectors, protective gloves or special apron

to protect you from grindings and material

particles. Eyes should be protected from ﬂying

debris that may be generated during certain

applications. Dust or ﬁlter masks must ﬁlter

any dust created by the application. If you are

exposed to loud noise for any length of time,

you can suﬀer a hearing loss.

j) Ensure that other people remain at a safe dis-

tance to your workspace. Anyone who enters

the workspace must wear personal protective

equipment. Fragments of the workpiece or bro-

ken accessory tools can ﬂy oﬀ and cause injury

– even outside the immediate working area.

k) Hold power tool by the insulated gripping

surfaces, when performing an operation

where the accessory tool may contact hidden

wiring or its own cord. Contact with a "live"

wire may make exposed metal parts of the pow-

er tool "live" and could give the operator an

electric shock.

l) Keep the power cord away from any rotating

accessories. If you lose control of the appliance,

the cord may get cut or caught and your hand or

arm could get caught in the rotating accessory

tool.

m) Never put the power tool down until the acces-

sory tool has come to a complete standstill.

The rotating accessory tool could come into

contact with the surface and cause you to lose

control of the power tool.

n) Do not leave the power tool running whilst

carrying it. Accidental contact between your

clothing and the rotating accessory tool could

cause your clothing to get caught and the ac-

cessory tool to penetrate a part of your body.

o) Clean the ventilation slits of your power tool

regularly. The engine fan draws dust into the

housing and a strong accumulation of metal

dust can cause electrical hazards.

p) Do not use the power tool in the vicinity of

ﬂammable materials. Sparks can ignite such

materials.

q) Do not use any accessory tools which require

liquid coolant. The use of water or other liquid

coolants may lead to electric shock.

PMNF 1350 B2

■ 6

│

GB

Further safety instructions for

abrasive cutting applications

Kickback and corresponding safety instructions

Kickback - causes and corresponding safety

instructions

▯ Kickback is a sudden reaction caused when a

rotating grinding disc catches or jams. Catching

or jamming causes the rotating accessory tool

to stop abruptly. If this happens, an uncontrolled

power tool turns rapidly against the direction

of rotation of the accessory tool caught in the

blockage.

▯ If, for example, a grinding disc catches or jams,

the edge of the grinding disc that is projecting

into the workpiece can get caught and break

oﬀ the grinding disc or cause a kickback. The

grinding disc can then ﬂy in the direction of the

operator or away from him, depending on the

direction of rotation of the disc at the blockage.

This can also break grinding discs.

A kickback is caused by incorrect use or misuse

of the power tool. This can be avoided by taking

proper precautions as given below.

a) Hold the power tool ﬁrmly in both hands and

position your arms so they can absorb the

force of a kickback. Always use the additional

handle, if available, so you have the maximum

control over the kickback force or reaction

torques at full speed. By taking adequate pre-

cautions, the operator can stay in control of the

kickback and reaction torques.

b) Never hold your hand close to a rotating

accessory tool. The accessory tool could hit

your hand in the case of a kickback.

c) Avoid the area in front of and behind the rotat-

ing cutting disc. The kickback will force the power

tool in the opposite direction to the direction of

rotation of the grinding disc at the blockage.

d) Take special care when working around

corners, sharp edges, etc. Avoid allowing

the accessory tool to bounce back from the

workpiece or jam. The rotating accessory tool

is more likely to jam in corners or sharp edges

or if it bounces. This can cause a loss of control

or kickback.

e) Do not use a toothed or chain saw blade or

segmented diamond-coated disc with more

than 10 mm wide slits. Such accessory tools

cause a kickback or loss of control over the

power tool.

f) Avoid cutting disc jams or excessive contact

pressure. Do not make any excessively deep

cuts. Overloading the cutting disc increases the

stress and likelihood of tilting or jamming and

thus the possibility of kickback or breakage of

the grinding tool.

g) If the cutting disc jams or you stop working,

switch the tool oﬀ and hold it steady until the

disc has completely stopped turning. Never

attempt to pull a rotating cutting disc out of a

cut. This could lead to kickback. Identify and

remove the cause of the jam.

h) Do not switch the power tool back on as long

as it is in the workpiece. Allow the cutting disc

to reach its full speed before you carefully

continue the cut. Otherwise, the disc may jam,

jump out of the workpiece or cause kickback.

i) Support panels or large workpieces to reduce

the risk of the cutting disc jamming and causing

a kickback. Large workpieces can bend under

their own weight. The workpiece must be sup-

ported on both sides, namely in the vicinity of

the cut and also at the edge.

j) Be particularly careful when making "pocket

cuts" into existing walls or other obscured

areas. The inserted cutting disc may cut into

gas or water pipes, electrical wiring or other

objects that can cause kickback.

PMNF 1350 B2

GB

│

7 ■

Supplementary notes

Approved cutting disc designs:

segmented diamond-coated discs with slits

between the segments with a maximum size

of 10 mm and a negative cutting angle:

Disc diameter: 125 mm

Disc thickness: 2.1 mm

Wear hearing protection!

Wear safety goggles!

Wear safety shoes!

Wear protective gloves!

Wear a dust mask!

Not approved for wet grinding!

Original accessories/auxiliary

equipment

■ Only use the accessories and additional equip-

ment that are speciﬁed in the operating instruc-

tions and are compatible with the appliance.

Before use

Setting the cut width of the diamond

cutting discs

♦ Loosen the locking screw .

♦ Push the depth stop

upwards.

♦ Press the spindle lock

and hold it down.

♦ Use the face spanner

to loosen the locking

ﬂange .

♦ Remove the locking ﬂange

.

♦ Set the desired cut width in accordance with

the number of blotters

. Ensure that the ﬂange

is set in place as the top intermediate layer

(see ﬁg. F).

NOTE

► There are several spacer washers available

for you. Ensure that the groove width is the total

of the spacer washers between the diamond

cutting discs and the thickness of the cutting

discs.

► Please make sure that the backing ﬂange

is ﬁxed well on the shaft. The backing ﬂange

must rotate with shaft.

► Please make sure that diamond disc ﬁxed

well on the ﬂanges

+ .

♦ Tighten the locking ﬂange

using the face span-

ner . Press the spindle lock while doing this.

NOTE

► When setting a cut width that is smaller than

the maximum cut width, you must use the

blotters

on the ﬁxing ﬂange side for ﬁxing

the cutting discs since the ﬁxing ﬂange cannot

ﬁx the discs alone on the spindle due to the

thread length (see ﬁg. G).

PMNF 1350 B2

■ 8

│

GB

Replacing the diamond cutting discs

(see Figures A - F)

NOTE

► Replace diamond cutting discs only in pairs.

♦ Loosen the locking screw

.

♦ Push the depth stop

upwards.

♦ Press the spindle lock and hold it down.

♦ Use the face spanner

to loosen the locking

ﬂange

.

♦ Take oﬀ all removable parts from the spindle.

♦ Clean the locking ﬂange

, ﬂange , blotters

and backing ﬂange thoroughly.

♦ Attach the backing ﬂange

(see Fig. A).

NOTE

► Make sure that the backing ﬂange

is

correctly attached by ensuring that it rotates

together with the spindle.

♦ Attach the ﬁrst diamond cutting disc (see

Fig. B).

♦ Set the desired cut width in accordance with

the number of blotters

. Ensure that the ﬂange

is set in place as the top blotter (see Fig. C

and F).

♦ Attach the second diamond cutting disc

(see Fig. D).

NOTE

► Make sure that the cutting discs are correctly

attached to the ﬂanges.

♦ Tighten the locking ﬂange

using the face

spanner . Press the spindle lock while

doing this (see Fig. E).

Setting the groove depth

♦ Loosen the locking screw .

♦ Set the depth stop

to the desired depth.

♦ Tighten the locking screw

.

Attaching the dust extraction adapter

♦ Push the pins of the dust extraction adapter

into the recesses on the dust extraction connector.

♦ Lock the dust extraction adapter

by turning it.

♦ Loosen the union nut

.

♦ Push the pipe of the extraction device far enough

into the opening on the union nut

.

♦ Tighten the union nut

fully.

Operation

Switching on and oﬀ

NOTE

► Always switch the appliance on before making

contact with the material, then apply it to the

workpiece. The wall grinder is equipped with

an electronic smooth start. The motor starts

with a delay.

Switching the appliance on:

♦ Activate the safety lock-out

(see fold-out

page). Then press the ON/OFF switch .

Switching the appliance oﬀ:

♦ Release the ON/OFF switch

.

PMNF 1350 B2

GB

│

9 ■

Handling the wall grinder

CAUTION!

► This appliance is designed for dry cutting only!

♦ Use a service line detector to check the internal

and external walls for concealed power, gas and

water supply lines before using the wall chaser.

♦ Select the desired groove width.

♦ 1.) Position the appliance with the roller

against the brick wall.

♦ 2.) Now switch the appliance on and plunge

it into the masonry until the stop

makes

contact.

♦ 3.) Then mill the groove in the masonry; pay

attention to the milling direction. The appli-

ance must always run in reverse rotation.

Otherwise the appliance could be pushed

out of the cut in an uncontrolled manner.

2

1

3

♦ At the end of the groove, swivel the appliance

out of the groove and only then switch the

appliance oﬀ.

♦ Now break out the resulting bar between the

two grooves using the hand chisel

.

CAUTION!

► Materials containing asbestos must not be

machined!

Maintenance and cleaning

WARNING! RISK OF INJURY! Switch

the appliance oﬀ and remove the

power plug before commencing

any work to the appliance.

■ The appliance must always be kept clean, dry

and free from oil or grease.

■ Use a soft, dry cloth to clean the housing.

Never use petrol, solvents or cleansers which

can damage plastic.

WARNING! If the connecting cable

needs to be replaced, this must be

carried out by the manufacturer or

an authorised representative in order

to avoid safety hazards.

■ Grinding tools are to be treated with care and

transported carefully. Grinding tools should be

stored in such a way that they are not exposed

to mechanical damage or harmful environmental

inﬂuences.

■ Never allow liquids to get into the appliance.

NOTE

► Replacement parts not listed (such as carbon

brushes, switch) can be ordered via our

service hotline.

Disposal

The packaging is made from environmen-

tally friendly material and can be

disposed oﬀ at your local recycling plant.

Do not dispose of power tools in

your normal household waste!

European Directive 2012/19/EU requires that

worn-out power tools be collected separately and

recycled in an environmentally compatible manner.

Please consult your local authorities regarding

suitable disposal of worn out power tools.

PMNF 1350 B2

■ 10

│

GB

Kompernass Handels GmbH

warranty

Dear Customer,

This appliance has a 3-year warranty valid from

the date of purchase. If this product has any faults,

you, the buyer, have certain statutory rights. Your

statutory rights are not restricted in any way by the

warranty described below.

Warranty conditions

The validity period of the warranty starts from the

date of purchase. Please keep your original receipt

in a safe place. This document will be required as

proof of purchase.

If any material or production fault occurs within

three years of the date of purchase of the product,

we will either repair or replace the product for you

at our discretion. This warranty service is dependent

on you presenting the defective appliance and

the proof of purchase (receipt) and a short written

description of the fault and its time of occurrence.

If the defect is covered by the warranty, your product

will either be repaired or replaced by us. The repair

or replacement of a product does not signify the

beginning of a new warranty period.

Warranty period and statutory claims for

defects

The warranty period is not prolonged by repairs

eﬀected under the warranty. This also applies to

replaced and repaired components. Any damage

and defects present at the time of purchase must

be reported immediately after unpacking. Repairs

carried out after expiry of the warranty period shall

be subject to a fee.

Scope of the warranty

This appliance has been manufactured in accordance

with strict quality guidelines and inspected meticu-

lously prior to delivery.

The warranty covers material faults or production

faults. The warranty does not extend to product parts

subject to normal wear and tear or fragile parts such

as switches, batteries, baking moulds or parts made

of glass.

The warranty does not apply if the product has been

damaged, improperly used or improperly maintained.

The directions in the operating instructions for the

product regarding proper use of the product are

to be strictly followed. Uses and actions that are

discouraged in the operating instructions or which

are warned against must be avoided.

This product is intended solely for private use and

not for commercial purposes. The warranty shall be

deemed void in cases of misuse or improper handling,

use of force and modiﬁcations/repairs which have

not been carried out by one of our authorised

Service centres.

Warranty claim procedure

To ensure quick processing of your case, please

observe the following instructions:

■ Please have the till receipt and the item number

(e.g. IAN 12345) available as proof of purchase.

■ You will ﬁnd the item number on the type plate,

an engraving on the front page of the instructions

(bottom left), or as a sticker on the rear or

bottom of the appliance.

■ If functional or other defects occur, please

contact the service department listed either by

telephone or by e-mail.

■ You can return a defective product to us free of

charge to the service address that will be provided

to you. Ensure that you enclose the proof of

purchase (till receipt) and information about

what the defect is and when it occurred.

You can download these instructions

along with many other manuals,

product videos and software on

www.lidl-service.com.

PMNF 1350 B2

GB

│

11 ■

Service

WARNING!

■ Have the power tool repaired by the service

centre or a qualiﬁed electrician and only

using genuine replacement parts. This will

ensure that the safety of the appliance is

maintained.

WARNING!

■ Always ensure that the power plug or

the mains cable is replaced only by the

manufacturer of the appliance or by an

approved customer service provider. This

will ensure that the safety of the appliance is

maintained.

NOTE

► Replacement parts not listed (such as carbon

brushes, switches) can be ordered via our

service hotline.

Service Great Britain

Tel.: 0871 5000 720 (£ 0.10/Min.)

E-Mail: [email protected]

IAN 280254

Importer

Please note that the following address is not the

service address. Please use the service address

provided in the operating instructions.

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

GERMANY

www.kompernass.com

Translation of the original

Conformity Declaration

We, KOMPERNASS HANDELS GMBH, docu-

ments oﬃcer: Mr. Semi Uguzlu, BURGSTR. 21,

44867 BOCHUM, GERMANY, hereby declare that

this product complies with the following standards,

normative documents and EC directives:

Machinery Directive

(2006/42/EC)

EMC (Electromagnetic Compatibility)

(2014/30/EU)

RoHS Directive

(2011/65/EU)*

*The manufacturer is solely responsible for issuance of

the declaration of conformity. The object of the decla-

ration described above is in conformity with Directive

2011/65/EU of the European Parliament and of the

Council of 8 June 2011 on the restriction of use of

certain hazardous substances in electrical and electronic

equipment.

Applied harmonised standards:

EN 60745-1:2009/A11:2010

EN 60745-2-22:2011/A11:2013

EN 55014-1:2006/A2: 2011

EN 55014-2:2015

EN 61000-3-2:2014

EN 61000-3-3:2013

Type designation of machine:

Wall chaser PMNF 1350 B2

Year of manufacture: 08 - 2016

Serial number: IAN 280254

Bochum, 06/09/2016

Semi Uguzlu

- Quality Manager -

The right to eﬀect technical changes in the context

of further development is reserved.

PMNF 1350 B2

■ 12

│

GB

PMNF 1350 B2

HU

│

13 ■

Tartalomjegyzék

Bevezető .......................................................14

Rendeltetésszerű használat ...................................................14

Felszereltség ............................................................... 14

A csomag tartalma ..........................................................14

Műszaki adatok ............................................................ 14

Általános biztonsági előírások elektromos kéziszerszámokhoz ..........15

1. A munkaterület biztonsága .................................................15

2. Elektromos biztonság ...................................................... 15

3. Személyi biztonság .......................................................16

4. Az elektromos kéziszerszám használata és kezelése .............................16

5. Szerviz ................................................................. 17

A vágókorongos csiszolóval kapcsolatos biztonsági utasítások ........................ 17

A vágással kapcsolatos további biztonsági utasítások ...............................18

Kiegészítő utasítások ........................................................ 19

Eredeti tartozékok / kiegészítő eszközök ......................................... 19

Üzembe helyezés előtt ............................................20

A gyémánt vágókorongok vágási szélességének beállítása ..........................20

Gyémánt vágókorongok cseréje (lásd az A-F ábrákat) ..............................20

Horonymélység beállítása ....................................................20

A porelszívó adapter felszerelése ..............................................21

Használat ......................................................21

Be- / kikapcsolás ...........................................................21

A falhoronymaró használata ..................................................21

Karbantartás és tisztítás ..........................................22

Ártalmatlanítás ..................................................22

JÓTÁLLÁSI TÁJÉKOZTATÓ ..........................................23

Szerviz .........................................................25

Gyártja ........................................................25

Az eredeti megfelelőségi nyilatkozat fordítása .......................25

PMNF 1350 B2

■ 14

│

HU

FALHORONYMARÓ

PMNF 1350 B2

Bevezető

Gratulálunk új készüléke megvásárlásához.

Vásárlásával kiváló minőségű termék mellett dön-

tött. A használati útmutató a termék része. Fontos

tudnivalókat tartalmaz a biztonságra, használatra

és ártalmatlanításra vonatkozóan. A termék hasz-

nálata előtt ismerkedjen meg valamennyi használa-

ti útmutatóval és biztonsági ﬁgyelmeztetéssel. Csak

a leírtak szerint és a megadott célokra használja

a készüléket. A készülék harmadik személynek

történő továbbadása esetén adja át a készülékhez

tartozó valamennyi leírást is.

Rendeltetésszerű használat

A falhoronymaró (más néven vágó-csiszoló gép)

- a továbbiakban készülék - vezetőszános stabil

felfekvéssel és engedélyezett ipari porszívóhoz

csatlakoztatva, elsősorban ásványi alapanyagok

(pl. beton vagy falazat) víz nélküli leválasztására

vagy bevágására használható. Minden egyéb

felhasználási mód vagy a gép módosítása rendel-

tetésellenesnek minősül és jelentős balesetveszélyt

rejt magában. A gép nem ipari használatra készült.

Felszereltség

BE/KI kapcsoló

markolat

porelszívó adapter

hollandi anya

védőburkolat

szorítókarima (menetes)

rögzítőcsavar a mélységütközőhöz

mélységütköző

pótmarkolat

kapcsolózár

orsóretesz

futógörgő

szűkítőelem

karima

köztes réteg

csavarkulcs

kézi véső

támasztókarima (befogókarima)

A csomag tartalma

1 falhoronymaró

2 vágókorong (felszerelve)

1 csavarkulcs

1 elszívóadapter (felszerelve)

1 szűkítő (az elszívóadapterrel és egy ∅ 32 mm

porszívótömlővel történő használathoz)

1 kézi véső

1 használati útmutató

Műszaki adatok

Névleges feszültség: 230 V ∼ 50 Hz

(váltóáram)

Névleges

teljesítményfelvétel: 1350 W

Névleges fordulatszám: n 9000 min

-1

Korong Ø: 125 mm

Befogó furat: 22,23 mm

Horonymélység: 0–30 mm

Horonyszélességek: min. 8 mm -

max. 26 mm

Menet: M14

Védelmi osztály: II / (dupla szigetelés)

Súly: kb. 4 kg

Zaj- és rezgésinformációk:

A zaj- és rezgésértékek az EN 60745 szabvány-

nak megfelelően kerültek meghatározásra.

Hangnyomásszint L

pA

: 98,0 dB(A)

Bizonytalansági érték K

pA

: 3 dB

Hangerőszint L

WA

: 109,0 dB(A)

Bizonytalansági érték K

WA

: 3 dB

Viseljen hallásvédőt!

A zaj halláskárosodást okozhat.

Rezgés összértéke (három irány vektorösszege),

az EN 60745 szabvány szerint mérve:

Rezgésértékre vonatkozó adat (betonlap levágása

esetén):

Markolat: a

h

= 5,450 m/s

2

Bizonytalansági érték K = 1,5 m/s

2

Pót-markolat: a

h

= 4,737 m/s

2

Bizonytalansági érték K = 1,5 m/s

2

PMNF 1350 B2

HU

│

15 ■

TUDNIVALÓ

► Jelen használati útmutatóban megadott rez-

gésszint az EN 60745 szabvány által meg-

határozott szabványos mérési eljárással lett

meghatározva és felhasználható a készülékek

összehasonlítására. A megadott rezgés kibo-

csátási érték a kitettség előzetes megbecsülé-

séhez is felhasználható.

FIGYELMEZTETÉS!

► A rezgésszint az elektromos kéziszerszám al-

kalmazásától függően változik és egyes ese-

tekben a jelen útmutatókban megadott érték

felett lehet. A rezgésterhelés alulbecsült lehet,

ha az elektromos kéziszerszámot rendszere-

sen így használják. Próbálja a rezgésterhelést

a lehető legalacsonyabb szinten tartani.

A rezgésterhelés csökkentésére tett intézke-

dések például a kesztyű viselése az eszköz

használata során és a munkaidő korlátozása.

Ebben az esetben a működési ciklus minden

részét ﬁgyelembe kell venni (például amikor

az elektromos kéziszerszám ki van kapcsolva,

és amikor bár be van kapcsolva, de terhelés

nélkül fut).

Általános biztonsági

előírások elektromos

kéziszerszámokhoz

FIGYELMEZTETÉS!

► Olvassa el az összes biztonsági előírást és

utasítást. A biztonsági előírások és utasítások

ﬁgyelmen kívül hagyása áramütést, tüzet és/

vagy súlyos sérüléseket okozhat.

Őrizze meg az összes biztonsági előírást és

utasítást későbbi használatra.

A biztonsági előírásokban használt „elektromos

kéziszerszám“ kifejezés hálózatról (hálózati kábe-

len át) üzemeltetett elektromos kéziszerszámokra

és akkumulátoros elektromos kéziszerszámokra

(hálózati kábel nélkül) vonatkozik.

1. A munkaterület biztonsága

a) Tartsa tisztán és jól megvilágítva a munkate-

rületét. A rendetlenség és a rosszul megvilágított

munkaterület balesetet okozhat.

b) Ne dolgozzon a készülékkel olyan robba-

násveszélyes környezetben, ahol gyúlékony

folyadékok, gázok vagy porok vannak. Az

elektromos kéziszerszámok szikráznak, amik

meggyújthatják a port vagy gőzöket.

c) Az elektromos kéziszerszám használata köz-

ben ne engedjen közel gyermekeket és más

személyeket. Ha elterelik a ﬁgyelmét, elveszít-

heti uralmát a készülék felett.

2. Elektromos biztonság

a) A készülék hálózati csatlakozójának illenie

kell a csatlakozóaljzatba. A csatlakozót sem-

milyen módon nem szabad megváltoztatni.

A védőföldelt elektromos kéziszerszámokat

ne használja adapterrel. A módosítatlan csatla-

kozó és a megfelelő csatlakozóaljzat használata

csökkenti az elektromos áramütés veszélyét.

b) Ügyeljen arra, hogy teste ne érintkezzen föl-

delt felülettel, mint például csővezeték, fűtőtest,

tűzhely vagy hűtőszekrény felületével. Az áram-

ütés kockázata nagyobb, ha teste földelve van.

c) Óvja az elektromos kéziszerszámot esőtől

vagy nedves környezettől. Növeli az áramütés

kockázatát, ha víz kerül az elektromos készülék-

be.

d) Ne használja a vezetéket rendeltetésellenes

célra, az elektromos kéziszerszámot ne vigye

és ne akassza fel a kábelnél fogva vagy ne a

kábelnél fogva húzza ki a csatlakozót az alj-

zatból. Tartsa távol a vezetéket hőtől, olajtól,

éles szegélyektől vagy mozgó alkatrészektől.

A sérült vagy összecsavarodott vezeték növeli

az áramütés kockázatát.

e) Ha a szabadban dolgozik az elektromos ké-

ziszerszámmal, akkor csak olyan hosszabbító

kábelt használjon, ami kültérre is engedélye-

zett. A kültéri használatra alkalmas hosszabbító

kábellel csökkentheti az áramütés veszélyét.

Stránka sa načítava ...

Parkside PMNF 1350 B2 Translation Of The Original Instructions

Parkside PMNF 1350 B2 Translation Of The Original Instructions

V iných jazykoch

Súvisiace články

Ďalšie dokumenty