Silvercrest SAR 28 A1 Operating Instructions Manual

Kategória
Automobilové mediálne prijímače
Typ
Operating Instructions Manual
IAN 85465
CAR RADIO SAR 28 A1
AUTORADIO
Bedienungsanleitung
AVTORADIO
Navodila za uporabo
AUTÓRÁDIÓ
Használati utasítás
AUTORÁDIO
Návod na obsluhu
CAR RADIO
Operating instructions
GB Operating instructions Page 1
HU Használati utasítás Oldal 31
SI Navodila za uporabo Stran 61
SK Návod na obsluhu Strana 91
DE / AT / CH Bedienungsanleitung Seite 121
Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the
device.
Olvasás előtt kattintson az ábrákat tartalmazó mindkét oldalra és végezetül ismerje meg a készülék
mindegyik funkcióját.
Pred branjem obe strani s slikami odprite navzven in se nato seznanite z vsemi funkcijami naprave.
Pred čítaním si odklopte obidve strany s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.
Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich anschließend
mit allen Funktionen des Gerätes vertraut.
B
A
C
D
1
SAR 28 A1
GB
Table of contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Limitation of liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Basic safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Items supplied and transport inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Disposal of packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Removing the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Using the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Face plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Handling and use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Switching on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Radio reset (RESET) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Radio functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
USB port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Card reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
MP3 / WMA playback functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Connecting an external audio device to the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Cleaning the display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Disposal of the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Fault rectifi cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Fault causes and rectifi cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Technical details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
EC Declaration of Conformity information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Importer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
IB_85465_SAR28A1_LB4.indb 1IB_85465_SAR28A1_LB4.indb 1 06.12.12 16:5006.12.12 16:50
2
Introduction
SAR 28 A1
GB
Introduction
Preface
Congratulations on the purchase of your new device.
You have decided to purchase a high-quality product. These operating instructions
are part of the SAR 28 A1 car radio (hereafter referred to as the device) and
provide you with important instructions pertaining to the intended use, safety,
installation, connection and operation of the device.
The operating instructions must be kept near to the device at all times. They are
to be read and applied by all those working on installation, servicing and fault
rectifi cation of the device.
Keep these operating instructions in a safe place and pass them on to any future
owner together with the device.
Copyright
This documentation is subject to copyright protection.
All rights, including those of photographic reproduction, duplication and distribu-
tion by means of particular methods (such as data processing, data carriers and
data networks), in whole or in part, as well as substantive and technical changes,
are reserved.
Limitation of liability
All technical information, data and information in these operating instructions
pertaining to installation, connection and operation correspond to the latest
versions at the time of printing and to the best of our knowledge take into due
consideration our previous experience and expertise.
No claims can be derived from the details, illustrations and descriptions in these
instructions.
The manufacturer assumes no liability for damage caused by failure to observe
these instructions, non-intended use, improper repairs, making unauthorised modi-
cations or using non-approved replacement parts.
IB_85465_SAR28A1_LB4.indb 2IB_85465_SAR28A1_LB4.indb 2 06.12.12 16:5006.12.12 16:50
3
Introduction
SAR 28 A1
GB
Warnings
The following warnings are used in these operating instructions:
WARNING
A warning of this risk level indicates a potentially hazardous
situation.
Not averting this hazardous situation could result in physical injury.
Follow the instructions in this warning to prevent physical injury.
CAUTION
A warning of this risk level indicates potential material damage.
Not averting this situation could result in material damage
Follow the instructions in this warning to prevent material damage.
NOTE
A notice indicates additional information that will assist you in handling the
device.
Intended use
This device is intended solely for the reception of FM radio stations, for the play-
back of MP3/WMA fi les from USB data carriers and SD/MMC memory cards,
as well as audio signals from external audio devices. The device is intended for
installation into a vehicle. The device is not intended for any other use or for uses
extending beyond those stated.
WARNING
Risks from non-intended use!
Risks can arise if the device is used for non-intended purposes and/or other
types of usage.
Only use the device for its intended purpose.
Observe the procedures described in these operating instructions.
Claims of any kind for damage arising as a result of non-intended use are
excluded. The user is the sole bearer of the risk.
IB_85465_SAR28A1_LB4.indb 3IB_85465_SAR28A1_LB4.indb 3 06.12.12 16:5006.12.12 16:50
4
Introduction
SAR 28 A1
GB
Safety
This section provides you with important safety information regarding the han-
dling of the device.
The device complies with statutory safety regulations. However, incorrect use can
result in injury and material damage.
Basic safety instructions
For safe handling of the device, follow the safety information below:
Before use, check the device for visible external damage. Do not use a
damaged device or one that has been dropped.
If the cables or connections are damaged, arrange for them to be exchanged
by an authorised specialist or customer service.
Those who, due to their physical, intellectual or motor abilities, are incapable
of using the device safely, may only use it whilst under the supervision or
direction of a person responsible.
Only permit children to use the device when under supervision.
Only have repairs carried out by authorised specialist companies or customer
service. Improper repairs can pose signifi cant risks to the user. Warranty
claims also become void.
Repairs to the device during the warranty period may only be carried out by
a customer service department authorised by the manufacturer. Otherwise
no additional warranty claims can be considered for subsequent damage.
Defective components may only be replaced with original replacement parts.
Only by using original replacement parts can it be guaranteed that safety
requirements are being complied with.
Protect the device from moisture and liquid penetration.
Tra c safety
WARNING
Road traffi c safety has the highest priority!
Observe the following safety instructions so as not to endanger yourself or
others:
Before starting your journey, familiarise yourself with how to use the device.
Only use the device when the traffi c situation allows it! Stop at a suitable
place if you wish to perform major confi gurations.
Only remove or insert the face plate when the vehicle is parked.
Set the volume to a moderate level so that the acoustic sirens of police
vehicles, fi re trucks and other emergency service vehicles can be heard in
good time.
IB_85465_SAR28A1_LB4.indb 4IB_85465_SAR28A1_LB4.indb 4 06.12.12 16:5006.12.12 16:50
5
Introduction
SAR 28 A1
GB
Items supplied and transport inspection
WARNING
Risk of suff ocation!
Packaging material must not be used as a play thing since it poses a risk of
suff ocation.
This device is supplied with the following components as standard:
Car Radio (including face plate)
Installation bracket (attached)
Fixture plate (including securing material)
Keys for installation frame (2x)
Case for face plate
This operating manual
NOTE
Check the contents for completeness and for signs of visible damage.
If the contents are not complete or are damaged due to defective packaging
or transportation, contact the service hotline (see warranty card).
Disposal of packaging
The packaging protects the device from damage caused during transit. The
packaging materials are selected according to their environmental friendliness
and disposal attributes - and are therefore recyclable.
Recirculation of packaging into the material fl ow saves on raw material and re-
duces the amount of waste generated. Dispose of packaging material no longer
needed in line with applicable local regulations.
NOTE
If possible, keep the device's original packaging during the warranty period
so that, in the event of a warranty claim, you can package the device
properly for its return.
IB_85465_SAR28A1_LB4.indb 5IB_85465_SAR28A1_LB4.indb 5 06.12.12 16:5006.12.12 16:50
6
Controls
SAR 28 A1
GB
Controls
Car radio (see front fold out fl ap)
Figure A:
Button : Unlocking the face plate
2
Button /MU: Switching the device on and off / turning the sound off
3
MD/PTY button: Setting the operating mode / setting the PTY function
4
Button ▸▸I: Title / Station search forwards
5
Display
6
USB port
7
BD/DISP: Selecting memory location band / showing display information
8
AUX: 3.5 mm stereo input socket for the connection of an external audio device
9
6/FL+ button: Station memory location 6 / directory forwards during MP3/WMA playback
10
5/FL- button: Station memory location 5 / directory backwards during MP3/WMA playback
11
4/RDM button: Station memory location 4 / random play during MP3/WMA playback
12
3/INT button: Station memory location 3 / intro function during MP3/WMA playback
13
2/RPT button: Station memory location 2 / repeat function during MP3/WMA playback
14
1/PAU button: Station memory location 1 / pause playback (Pause)
15
I◂◂: Title / Station search backwards
16
A/PS
: Automatic station memory / search function during MP3/WMA playback
17
Multi-controller: Turn to set values/volume
18
SEL (EQ/LD TA/AF) button: Call up Settings menu
Figure B:
19
Locking the face plate
20
Holder for face plate
21
Card reader for SD/MMC cards
22
RESET: Resetting the device
Figure C:
23
ISO block connection B
24
Automotive blade type fuse 7.5 A
25
ISO block connection A
26
SUBW: Audio cinch output for subwoofer
27
LINE OUT: Audio cinch output L/R for amplifi er
28
Antenna socket for DIN antenna plug
IB_85465_SAR28A1_LB4.indb 6IB_85465_SAR28A1_LB4.indb 6 06.12.12 16:5006.12.12 16:50
7
Installation
SAR 28 A1
GB
Accessories (see rear fold out fl ap)
Figure D:
29
Case for face plate
30
Installation bracket
31
Key for installation bracket
32
Anchoring plate (including securing material)
Installation
WARNING
Damage can be caused when installing the device!
If possible, have the device installed by a qualifi ed technician.
If you wish to install the device yourself, follow the instructions for connec-
tion and installation for safe, fault-free use of the device.
Connection
CAUTION
Using incorrect connections can cause damage to the device.
For installation, use the device's ISO connections. The vehicle-specifi c ISO
adapters you may require can be sourced from a specialist workshop, from
a local dealer or from a general store's technical department. Using other
connector types voids the warranty.
Assignment of the ISO connections
The view of the plug connector is from behind.
1357
2468
ISO A
(power supply
assignment)
Assignment
1 Not used
2 Not used
3 Not used
4
Steady plus 12 V
(terminal 30)
5 Antenna power
6 Not used
7
Ignition circuit positive 12 V
(terminal 15)
8
Negative (-)
ground (terminal 31)
IB_85465_SAR28A1_LB4.indb 7IB_85465_SAR28A1_LB4.indb 7 06.12.12 16:5006.12.12 16:50
8
Installation
SAR 28 A1
GB
1357
2468
ISO B
(speaker connec-
tion assignment)
Assignment
1 Rear right +
2 Rear right -
3 Front right +
4 Front right -
5 Front left +
6 Front left -
7 Rear left +
8 Rear left -
To connect the device to two speakers, only use the cables for the front speakers.
NOTE
Ensure that a steady plus connection is applied to the station memory of
connector 4 in ISO Block A.
In some vehicle models, the default assignment of connectors [4] and [7]
in ISO Block A are interchanged at the factory. If this is the case, the station
memory can be lost. To remedy this, connectors 7 (Ignition positive) and
4 (Steady plus) in ISO Block A must be swapped.
Antenna power connector
CAUTION
Possible damage to the device
Never load the antenna power connection with the antenna motor power
cable or other consumers.
The connector for the antenna power is available for a relay-controlled antenna.
The relay then automatically extends the antenna out when the device is switched
on. When switched off , the antenna retracts back in. This connector can also be
used to control an external amplifi er. For exact connector information, please
consult the operating instructions for the amplifi er.
Connection of an external amplifi er
Use the LINE OUT
27
audio cinch output to connect an external amplifi er.
To do this, following the operating instructions for the external amplifi er.
IB_85465_SAR28A1_LB4.indb 8IB_85465_SAR28A1_LB4.indb 8 06.12.12 16:5006.12.12 16:50
9
Installation
SAR 28 A1
GB
Connection of an external subwoofer
Use the orange SUBW
26
cinch output to connect an external subwoofer.
To do this, follow the operating instructions for the external subwoofer.
Connection diagram
1234
5678
1234
5678
ISO
A
ISO B
Installation
The device can be installed into any standard ISO mounting bay. In the event that
your vehicle does not have an ISO mounting bay, contact your local specialist
workshop, local dealer or the technical department of a general store.
NOTE
Connect up the cables before fi nally installing the device.
Ensure that it is plugged in properly and that the system works correctly.
Installation instructions
Install the device in the bay provided or select the installation location so
that all buttons can be reached easily without the driver being impeded.
Only connect the device to a 12 V car battery that is installed properly.
Only connect up the device within the vehicle via the ISO plugs.
Install the device in such a way as to prevent heat build-up and so that the
device is adequately ventilated.
External amplifi er
SubwooferAntenna
IB_85465_SAR28A1_LB4.indb 9IB_85465_SAR28A1_LB4.indb 9 06.12.12 16:5006.12.12 16:50
10
Installation
SAR 28 A1
GB
Do not install the device where it is subjected to high temperatures (i.e. direct
sunlight or heating vents), heavy contamination or strong vibrations.
Should modifi cations to the vehicle be necessary, contact your vehicle dealer
or specialist workshop.
Installing the device into the ISO bay
Remove the installation bracket
30
from the device housing.
Place the installation bracket into the ISO mounting bay.
Bend the tabs on the installation bracket with a screwdriver so that the
bracket is fi xed fi rmly into the mounting bay (see diagram).
Check to ensure the bracket is securely fi xed.
Connect the ISO socket block of the device to the two ISO plugs on your
vehicle.
Connect the cable from the vehicle antenna to the antenna socket
28
on the
device. The vehicle-specifi c ISO adapters you may require can be sourced
from a specialist workshop, from a local dealer or from a general store’s
technical department.
If required, connect the audio cinch cable of an external amplifi er to the
LINE OUT
27
socket on the device.
If required, connect the audio cinch cable of an external subwoofer to the
orange SUBW
26
cinch socket on the device.
Protect your device against theft with additional measures as required.
Attach the securing screw with the anchoring plate
32
and the securing
material to the engine fi rewall of the vehicle.
IB_85465_SAR28A1_LB4.indb 10IB_85465_SAR28A1_LB4.indb 10 06.12.12 16:5006.12.12 16:50
11
Installation
SAR 28 A1
GB
CAUTION
Possible damage to the cable!
To avoid damage, observe the position of the cables when sliding the
device into the bay.
Carefully push the device into the installation bracket
30
until it locks into
place.
After all the connections have been established, press the RESET
22
button
for about 6 seconds with a ballpoint pen or other sharp object.
Attach the face plate as described under “Installing the face plate”.
Removing the device
To remove the installed device, proceed as follows:
Insert the right and left keys
31
into their respective slots on the sides of the
device. (The tabs are now bent back).
Pull the device out.
IB_85465_SAR28A1_LB4.indb 11IB_85465_SAR28A1_LB4.indb 11 06.12.12 16:5006.12.12 16:50
12
Using the device
SAR 28 A1
GB
Using the device
Face plate
You are able to remove the face plate from your device as an anti-theft measure.
Do not keep the face plate in your vehicle after removal.
NOTE
Always keep the face plate in its case
29
to protect it.
Inserting the face plate
First, place the face plate with its right-hand
side against the holder
20
.
Then press the left-hand side into the frame until
the locking mechanism
19
engages.
Check to ensure that the face plate is installed cor-
rectly and securely in the frame. Not installing the
face plate correctly can result in malfunctions when
using the device.
2.
1.
Removing the face plate
Press the button to unlock the face
plate. The left-hand side of the face plate jumps
forwards slightly.
Remove the face plate by its left-hand side fi rst,
then by its right-hand side.
IB_85465_SAR28A1_LB4.indb 12IB_85465_SAR28A1_LB4.indb 12 06.12.12 16:5006.12.12 16:50
13
Handling and use
SAR 28 A1
GB
Handling and use
This section provides you with important information on handling and using the
device.
NOTE
If no setting is confi gured and/or no button pushed within about 5 seconds,
the device returns to its previous operating mode. Settings changed are saved.
Switching on and off
Press the /MU
2
button to switch the device on. The WELCOME display
is shown.
To switch off , keep the /MU button pressed. The GOODBYE display is
shown.
Settings
WARNING
Hearing damage as a result of too high a volume!
Setting the volume too high can result in permanent hearing damage.
Set the volume to moderate levels only.
Volume
Turn the multi-controller
17
to set the volume.
Switching mute on / off
Press the /MU button briefl y to turn the sound off . The MUTE ON message
appears in the display.
Press the /MU button again to turn the sound on again. Muting is
cancelled when receiving a PTY or TA station.
Operating mode
Press the MD/PTY
3
button to switch between radio reception (TUNER),
card reader (CARD), USB port (USB) and audio input (AUX).
NOTE
The CARD and USB operating modes can only be enabled once the appro-
priate medium has been inserted.
IB_85465_SAR28A1_LB4.indb 13IB_85465_SAR28A1_LB4.indb 13 06.12.12 16:5006.12.12 16:50
14
Handling and use
SAR 28 A1
GB
Display
Keep pressing the BD/DISP
7
button to have the following information
displayed in turn:
Radio station, time (automatically set with RDS reception), frequency and PTY set-
tings (these RDS functions are sent by broadcasting services in various volumes;
also refer to Section “Radio functions”).
NOTE
If you are not receiving any RDS or PTY information, PTY NONE is shown on
the display.
Radio reset (RESET)
To reset the device to its default factory settings, keep the RESET
22
button
pressed for about 6 seconds with a sharp object, such as a pen.
NOTE
To access the RESET button, the face plate must be completely removed,
see also Section "Removing the face plate".
Reset the device:
when using for the fi rst time,
after connecting the cables,
when not all function buttons are working,
when an error message is shown on the display.
Settings using the SEL button (EQ/LD/TA/AF)
Press the SEL
18
button on the device. The current volume level is shown.
Each further press of the SEL button accesses the next setting.
The following settings are possible:
VOL - Volume (from 0 to 47)
BAS - Bass (from -7 to +7)
TRE - Treble (from -7 to +7)
BAL - Balance (sound distribution between the right and left speakers),
from 0L to 9L and 0R to 9R
FAD - Fader (sound distribution between the front and rear speakers),
from 0F to 9F and 0R to 9R
Turn the multi-controller
17
to change the settings of the menu item
displayed.
IB_85465_SAR28A1_LB4.indb 14IB_85465_SAR28A1_LB4.indb 14 06.12.12 16:5006.12.12 16:50
15
Handling and use
SAR 28 A1
GB
Further settings using the SEL button (EQ/LD/TA/AF)
Hold down the SEL
18
button for about 2 seconds and then keep pressing
the SEL button until the required function is shown on the display.
Turn the multi-controller
17
to change the settings of the menu item dis-
played.
TA - Enabling / disabling Traffi c Announcement (traffi c information)
TA ON: If TA mode is enabled, the device immediately switches from other sta-
tions or operating modes to the radio station that is currently transmitting traffi c
information.
NOTE
When the TA function is enabled, you can only search for or save stations
that are transmitting traffi c information. Stations that are transmitting traffi c
information signals are denoted in the display by TP.
TA OFF: The TA function is disabled.
AF - Enabling / disabling Alternative Frequencies
AF ON: When the AF function is enabled, the device searches for the current
station’s optimum frequency.
AF OFF: The AF function is disabled.
EQ - Equaliser
Turn the multi-controller to select one of the FLAT, CLASSIC, ROCK, POP or
EQ OFF settings. No equaliser is enabled if EQ OFF is set. The equaliser
setting is shown at the bottom of the display.
SUBW - Subwoofer
You can connect an active external subwoofer to produce a more powerful bass
eff ect.
Turn the multi-controller to enable the bass eff ect (SUBW ON) or disable it
(SUBW OFF).
AVOL - Set the volume when radio is switched on
Turn the multi-controller to set the volume level used when the radio is turned on.
IB_85465_SAR28A1_LB4.indb 15IB_85465_SAR28A1_LB4.indb 15 06.12.12 16:5006.12.12 16:50
16
Handling and use
SAR 28 A1
GB
STEREO / MONO - Set the audio output
Turn the multi-controller
17
to set the audio output in radio mode to stereo
(STEREO) or mono (MONO). If you are receiving a stereo station, the stereo
symbol
appears on the display.
LOUD - Enable / disable the loudness function
Turn the multi-controller to increase base or treble levels (LOUD ON) or to
disable the function (LOUD OFF). When the loudness function is enabled,
LOUD is shown on the right of the display.
Dx / LOCAL - Set reception sensitivity
Turn the multi-controller to align the reception sensitivity to national stations
(DX) or regional stations (LOCAL).
ADJ - Set the time
NOTE
The device has an RDS-controlled clock. The clock sets itself automatically
when the RDS function is enabled and continues to run when the radio is
switched off . If you do not receive any RDS signal, you can set the time of
day manually.
Turn the multi-controller to the right to set the minutes and to the left to set
the hours.
IB_85465_SAR28A1_LB4.indb 16IB_85465_SAR28A1_LB4.indb 16 06.12.12 16:5006.12.12 16:50
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155

Silvercrest SAR 28 A1 Operating Instructions Manual

Kategória
Automobilové mediálne prijímače
Typ
Operating Instructions Manual

V iných jazykoch