Parkside PKS 1500 A2 Operating And Safety Instructions Manual

IAN 290768

MITRE SAW PKS 1500 A2

HU SI

CZ SK

FEJEZŐ- ÉS GÉRVÁGÓ FŰRÉSZ

Kezelési és biztonsági útmutató

Az eredeti használati útmutató fordítása

HU

ČELILNA IN ZAJERALNA ŽAGA

Napotki za upravljanje in varnost

Prevod originalnih navodil za uporabo

SI

POKOSOVÁ PILA

Pokyny k obsluze a bezpečnostní pokyny

Překlad originálního návodu k obsluze

CZ

SKRACOVACIA A POKOSOVÁ PÍLA

Upozornenia k obsluhe a bezpečnostné upozornenia

Preklad originálu návodu na obsluhu

SK CHAT

KAPP- UND GEHRUNGSSÄGE

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung

DE

MITRE SAW

Operating and Safety Instructions

Translation of Original Operating Manual

GB

GB Operation and Safety Notes Page 01

HU Kezelési és biztonsági útmutató Oldal 12

SI Napotki za upravljanje in varnost Stran 25

CZ Pokyny k obsluze a bezpečnostní pokyny Strana 37

SK Upozornenia k obsluhe a bezpečnostné upozornenia Strana 48

DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 60

Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik funkcióját.

HU

Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.

SI

Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.

CZ

Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

SK

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen Funktionen des Gerätes vertraut.

DE AT CH

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device.

GB

Read and follow the operating and safety instructions before you start working with this power tool!

HU

Üzembe helyezés előtt olvassa el a kezelési útmutatót és a biztonsági előírásokat, és mindig tartsa be azokat!

SI

Pred zagonom preberite navodila za uporabo in varnostne napotke ter jih upoštevajte!

CZ

Před uvedením do provozu si přečtěte a dodržujte návod k obsluze a bezpečnostní pokyny!

SK

Pred uvedením do prevádzky si prečítajte návod na obsluhu a bezpečnostné upozornenia a dodržiavajte ich!

DE AT CH

Vor Inbetriebnahme Bedienungsanleitung und Sicherheitshinweise lesen und beachten!

GB

Wear safety goggles!

HU

Viseljen védőszemüveget!

SI

Nosite zaščitna očala!

CZ

Noste ochranné brýle!

SK

Noste ochranné okuliare!

DE AT CH

Schutzbrille tragen!

GB

Important! Risk of injury! Never reach into the running saw blade!

HU

Figyelem! Sérülésveszély! Ne nyúljon a működő fűrészlaphoz!

SI

Pozor! Nevarnost poškodb! Ne posegajte v delujoč žagin list!

CZ

Pozor! Nebezpečí poranění! Nedotýkejte se pilového listu v provozu!

SK

Pozor! Nebezpečenstvo poranenia! Nesiahajte do bežiaceho pílového kotúča!

DE AT CH

Achtung! Verletzungsgefahr! Nicht in das laufende Sägeblatt greifen!

GB

Attention! Laser beam

HU

Figyelem! Lézersugárzás

SI

Pozor! Lasersko žarčenje

CZ

Pozor! Laserové záření

SK

Pozor! Laserové žiarenie

DE AT CH

Achtung! Laserstrahlung

GB

Protection class II (double insulation)

HU

Védelmi osztály II (Dupla szigetelés)

SI

Razred zaščite II (Dvojna izolacija)

CZ

Třída ochrany II (Dvojitá izolace)

SK

Trieda ochrany II (Dvojitá izolácia)

DE AT CH

Schutzklasse II (Doppelisolierung)

GB

Wear ear-muffs!

HU

Viseljen hallásvédőt!

SI

Nosite zaščito sluha!

CZ

Noste ochranná sluchátka!

SK

Noste ochranu sluchu!

DE AT CH

Gehörschutz tragen!

GB

Wear a breathing mask!

HU

Porképződésnél viseljen légzőmaszkot!

SI

Pri prašenju nosite zaščito dihal!

CZ

Bude-li se při práci prášit, noste ochranu dýchacích cest!

SK

Pri tvorbe prachu noste ochranu dýchania!

DE AT CH

Bei Staubentwicklung Atemschutz tragen!

10

17

14

15

16

1

3

2

4

5

6

7

8

9

10

11

12

13

Fig. 1

19

18

Fig. 1.2

Fig. 1.3

27a

27b

27

Fig. 1.3

Fig. 2

20

21

Fig. 2

Fig. 3

24

23

25

22

Fig. 3

Fig. 1.1

Fig. 5

28

29

6

2

3

27

26

1

34

Fig. 4

Fig. 5

Fig. 7

32

31

Fig. 7

Fig. 6

30

33

Fig. 6

GB

1

Table of contents: Page:

Introduction 2

Proper use 3

Important information 3

Additional safety instructions 4

Residual risks 6

Assembly 6

Commissioning 6

Area of application 7

Settings 7

Working instructions 7

Electrical connection 8

Accessories 9

Maintenance 9

Disposal 9

Troubleshooting 10

Guarantee Certificate 11

Declaration of conformity 72

GB

2

Introduction

MANUFACTURER:

scheppach

Fabrikation von Holzbearbeitungsmaschine GmbH

Günzburger Straße 69

D-89335 Ichenhausen

NOTE:

According to the applicable product liability laws, the manu-

facturer of the device does not assume liability for damages

to the product or damages caused by the product that occurs

due to:

• Improper handling,

• Non-compliance of the operating instructions,

• Repairs by third parties, not by authorized service techni-

cians,

• Installation and replacement of non-original spare parts,

• Application other than speciﬁed,

• A breakdown of the electrical system that occurs due to

the non-compliance of the electric regulations and VDE

regulations 0100, DIN 57113 / VDE0113.

WE RECOMMEND:

Read through the complete text in the operating instructions

before installing and commissioning the device. The operat-

ing instructions are intended to help the user to become

familiar with the machine and take advantage of its applica-

tion possibilities in accordance with the recommendations.

The operating instructions contain important information

on how to operate the machine safely, professionally and

economically, how to avoid danger, costly repairs, reduce

downtimes and how to increase reliability and service life of

the machine.

In addition to the safety regulations in the operating instruc-

tions, you have to meet the applicable regulations that apply

for the operation of the machine in your country. Keep the

operating instructions package with the machine at all times

and store it in a plastic cover to protect it from dirt and mois-

ture. Read the instruction manual each time before operating

the machine and carefully follow its information. The machine

can only be operated by persons who were instructed con-

cerning the operation of the machine and who are informed

about the associated dangers. The minimum age requirement

must be complied with.

In addition to the safety notes contained in the present oper-

ating instructions and the special regulations of your country,

the generally recognized technical rules for the operation of

machines must be observed.

Legend of Fig. 1

1 Start button

2 Handle

3 Locking lever

4 Motor

5 Saw blade

6 Moving saw blade guard

7 Base

8 Table insert

9 Rotary table

10 Workpiece clamp

11 Housing / base joint

12 Dust bag

13 Stationary saw blade guard

PKS 1500 A2

Scope of delivery

Mitre saw

Dust bag

Workpiece clamp

Tool for changing the saw

blade – 6mm Allen key

Tool for stop rail – 3mm Allen

key

2 work piece supports

Support stand

2 batteries (AAA)

2 carbon brushes

Operating instructions

Technical Data

Dimensions L x W x

H mm

690 x 550 x 440

Rotary table ø mm

385 x 150

Table height mm

55

Saw blade Ø mm

210/30/2,6/1,6

Number of teeth

48

Speed rpm

5000

Cutting speed m/s

55

Pivot range

2 x 45°

Tilt angle

45°

Double mitre

45° x 45°

left

Catch positions

45°, 30°, 22, 5°, 15°, 0°,

15°, 22, 5°, 30°, 4 5°

Weight kg

7, 7

Cross-cutting data

Max. cut depth

90°/45°

60 / 35 mm

90°/90°

120 x 60 mm

90°/45°

80 x 60 mm

45°/90°

120 x 35 mm

45°/45°

80 x 35 mm

Drive

Motor V~/Hz

220-240 / 50

Rated input W

S1 1200W

S6 25%* 1500W

Technical changes reserved!

GB

3

*S6, continuous operation periodic duty.

Identical duty cycles with a period at load followed by a

period at no load. Running time 10 minutes; duty cycle is

25% of the running time.

The work piece must have a minimum

height of 3mm and a minimum width of 10

mm. Make sure that the workpiece is al-

ways secured with the clamping device.

Information about noise development

The noise levels of this machine during operation are as

follows:

L

pA

: 99.6dB(A) K=3dB(A)

L

wA

: 112.6dB(A) K=3dB(A)

Warning: Noise can have serious eﬀects on your health.

If the machine noise exceeds 85 dB (A), please wear suitable

hearing protection. If the electrical connection is defective,

the power can fail when starting the machine. This could in-

ﬂuence other machines (e.g. blinking lamps). If the electrical

power corresponds to Zmax < 0.27, such disruptions should

not occur. (However, if they do, inform your specialist dealer).

• The speciﬁed vibration emission value has been meas-

ured according to a standardised testing procedure and

can be used for comparison of one electric tool with

another;

• The speciﬁed vibration emission value can also be used

for an initial assessment of the load.

Proper use

The mitre saw is used for the cutting of wood and plastic,

according to the machine size.

Warning! The supplied saw blade is only intended for

the sawing of wood! Do not use this blade for the sawing

of plastic!

The saw is not suitable for the cutting of ﬁrewood.

The machine may only be used in the intended manner.

Only suitable saw blades may be used for the machine.

The use of any type of cutting wheels is prohibited.

An element of the intended use is also the observance of

the safety instructions, as well as the assembly instructions

and operating information in the operating manual.

Persons who operate and maintain the machine must be

familiar with the manual and must be informed about po-

tential dangers.

Any use beyond this is improper. The user/operator, not the

manufacturer, is responsible for damages or injuries of any

type resulting from this.

In addition, the applicable accident prevention regulations

must be strictly observed.

Other general occupational health and safety-related rules

and regulations must be observed.

The liability of the manufacturer and resulting damages are

excluded in the event of modiﬁcations of the machine.

Despite use as intended, speciﬁc risk factors cannot be

entirely eliminated. Due to the design and layout of the ma-

chine, the following risks remain:

• Contact with the saw blade in the non-covered saw

area.

• Reaching into the running saw blade (cutting injury).

• Kick-back of workpieces and workpiece parts.

• Saw blade breakage.

• Ejection of faulty carbide parts of the saw blade.

• Hearing damage when the necessary hearing protection

is not used.

• Harmful emissions of wood dusts during use in enclosed

areas.

Please observe that our equipment was not designed with

the intention of use for commercial or industrial purposes.

We assume no guarantee if the equipment is used in com-

mercial or industrial applications, or for equivalent work.

Important information

Attention! The following basic safety measures must be

observed when using electric tools for protection against

electric shock, and the risk of injury and ﬁre. Read all these

notices before using the electric tool and keep the safety

instructions for later reference.

Safe work

1 Keep the work area orderly

– Disorder in the work area can lead to accidents.

2 Take environmental inﬂuences into account

– Do not expose electric tools to rain.

– Do not use electric tools in a damp or wet environment.

– Make sure that the work area is well-illuminated.

– Do not use electric tools where there is a risk of ﬁre or

explosion.

3 Protect yourself from electric shock

– Avoid physical contact with earthed parts (e.g. pipes,

radiators, electric ranges, cooling units).

4 Keep other persons away

– Do not allow other persons, especially children, to

touch the electric tool or the cable. Keep them away

from your work area.

– The operating person must be at least 18 years of

age; trainees must be at least 16 years, however only

under supervision.

5 Securely store unused electric tools

– Unused electric tools should be stored in a dry, el-

evated or closed location out of the reach of children.

6 Do not overload your electric tool

– They work better and more safely in the speciﬁed

output range.

7 Use the correct electric tool

– Do not use low-output electric tools for heavy work.

– Do not use the electric tool for purposes for which it

is not intended. For example, do not use handheld

circular saws for the cutting of branches or logs.

– Do not use the electric tool to cut ﬁrewood.

8 Wear suitable clothing

– Do not wear wide clothing or jewellery, which can

become entangled in moving parts.

– When working outdoors, anti-slip footwear is recom-

mended.

– Tie long hair back in a hair net.

GB

4

9 Use protective equipment

– Wear protective goggles.

– Wear a mask when carrying out dust-creating work.

10 Connect the dust extraction device

– If connections for dust extraction and a collecting de-

vice are present, make sure that they are connected

and used properly.

– Operation in enclosed areas is only permitted with a

suitable extraction system.

11 Do not use the cable for purposes for which it is not

intended

– Do not use the cable to pull the plug out of the outlet.

Protect the cable from heat, oil and sharp edges.

12 Secure the workpiece

– Use the clamping devices or a vice to hold the

workpiece in place. In this manner, it is held more

securely than with your hand.

– An additional support is necessary for long work-

pieces (table, trestle, etc.) in order to prevent the

machine from tipping over.

– Always press the workpiece ﬁrmly against the work-

ing plate and stop in order to prevent bouncing and

twisting of the workpiece.

13 Avoid abnormal posture

– Make sure that you have secure footing and always

maintain your balance.

– Avoid awkward hand positions in which a sudden

slip could cause one or both hands to come into

contact with the saw blade.

14 Take care of your tools

– Keep cutting tools sharp and clean in order to be

able to work better and more safely.

– Follow the instructions for lubrication and for tool

replacement.

– Check the connection cable of the electric tool regu-

larly and have it replaced by a recognised specialist

when damaged.

– Check extension cables regularly and replace them

when damaged.

– Keep the handle dry, clean and free of oil and

grease.

15 Pull the plug out of the outlet

– Never remove loose splinters, chips or jammed wood

pieces from the running saw blade.

– During non-use of the electric tool or prior to mainte-

nance and when replacing tools such as saw blades,

bits, milling heads.

16 Do not leave a tool key inserted

– Before switching on, make sure that keys and adjust-

ing tools are removed.

17 Avoid inadvertent starting

– Make sure that the switch is switched oﬀ when plug-

ging the plug into an outlet.

18 Use extension cables for outdoors

– Only use approved and appropriately identiﬁed

extension cables for use outdoors.

– Only use cable reels in the unrolled state.

19 Remain attentive

– Pay attention to what you are doing. Remain sensible

when working. Do not use the electric tool when you

are distracted.

20 Check the electric tool for potential damage

– Protective devices and other parts must be carefully in-

spected to ensure that they are fault-free and function

as intended prior to continued use of the electric tool.

– Check whether the moving parts function faultlessly

and do not jam or whether parts are damaged. All

parts must be correctly mounted and all conditions

must be fulﬁlled to ensure fault-free operation of the

electric tool.

– The moving protective hood may not be ﬁxed in the

open position.

– Damaged protective devices and parts must be

properly repaired or replaced by a recognised

workshop, insofar as nothing diﬀerent is speciﬁed in

the operating manual.

– Damaged switches must be replaced at a customer

service workshop.

– Do not use any faulty or damaged connection cables.

– Do not use any electric tool on which the switch can-

not be switched on and oﬀ.

21 ATTENTION!

– Exercise elevated caution for double mitre cuts.

22 ATTENTION!

– The use of other insertion tools and other accessories

can entail a risk of injury.

23 Have your electric tool repaired by a qualiﬁed electrician

– This electric tool conforms to the applicable safety

regulations. Repairs may only be performed by an

electrician using original spare parts. Otherwise ac-

cidents can occur.

Additional safety instructions

1 Safety precautions

– Warning! Do not use damaged or deformed saw

blades.

– Replace a worn table insert.

– Only use saw blades recommended by the manufac-

turer which conform to EN 847-1.

– Make sure that a suitable saw blade for the material

to be cut is selected.

– Wear suitable personal protective equipment. This

includes:

– Hearing protection to avoid the risk of becoming

hearing impaired,

– Respiratory protection to avoid the risk of inhaling

harmful dust,

– Wear gloves when handling saw blades and

rough materials. Carry saw blades in a container

whenever practical.

– Wear goggles. Sparks generated during work

or splinters, chippings and dust coming from the

device can lead to loss of eyesight.

– Connect a dust collecting device to the electric tool

when sawing wood. The emission of dust is inﬂu-

enced, among other things, by the type of material

to be processed, the signiﬁcance of local separation

(collection or source) and the correct setting of the

hood/guide plates/guides.

– Do not use saw blades made of high-speed alloy

steel (HSS steel).

GB

5

2 Maintenance and repair

– Pull out the mains plug for any adjustment or repair

tasks.

– The generation of noise is inﬂuenced by various

factors, including the characteristics of saw blades,

condition of saw blade and electric tool. Use saw

blades which were designed for reduced noise de-

velopment, insofar as possible. Maintain the electric

tool and tool attachments regularly and if necessary,

initiate repairs in order to reduce noise.

– Report faults on the electric tool, protective devices

or the tool attachment to the person responsible for

safety as soon as they are discovered.

3 Safe work

– Only use saw blades for which the maximum permis-

sible speed is not lower than the maximum spindle

speed of table saws and which are suitable for the

material to be cut.

– Make sure that the saw blade does not touch the

rotary table in any position by pulling out the mains

plug and rotating the saw blade by hand in the 45°

and 90° position. If necessary, readjust the saw

head.

– When transporting the electric tool, only use the

transport devices. Never use the protective devices

for handling or transport.

– Make sure that the lower part of the saw blade is cov-

ered during transport, e.g. by the protective device.

– Be sure to only use spacers and spindle rings speci-

ﬁed by the manufacturer as suitable for the intended

purpose.

– The ﬂoor around the machine must be level, clean

and free of loose particles, such as chips and cutting

residues.

– Do not remove any cutting residues or other parts of

workpieces from the cutting zone while the machine

is running with unprotected saw blade and the saw

unit is not at rest.

– Make sure that the machine is always secured on a

workbench or a table if at all possible.

– Support long workpieces (e.g. with a roller table) to

prevent them sagging at the end of a cut.

Warning! This electric tool generates an electromagnetic

ﬁeld during operation. This ﬁeld can impair active or passive

medical implants under certain conditions. In order to prevent

the risk of serious or deadly injuries, we recommend that per-

sons with medical implants consult with their physician and

the manufacturer of the medical implant prior to operating

the electric tool.

SAFETY INSTRUCTIONS FOR THE HANDLING

OF SAW BLADES

1 Only use insertion tools if you have mastered their use.

2 Observe the maximum speed. The maximum speed

speciﬁed on the insertion tool may not be exceeded. If

speciﬁed, observe the speed range.

3 Observe the motor / saw blade direction of rotation.

4 Do not use any insertion tools with cracks. Sort out

cracked insertion tools. Repairs are not permitted.

5 Clean grease, oil and water oﬀ of the clamping surfaces.

6 Do not use any loose reducing rings or bushes for the

reducing of holes on saw blades.

7 Make sure that ﬁxed reducer rings for securing the

insertion tool have the same diameter and have at least

1/3 of the cutting diameter.

8 Make sure that ﬁxed reducer rings are parallel to each other.

9 Handle insertion tool with caution. They are ideally

stored in the originally package or special containers.

Wear protective gloves in order to improve grip and to

further reduce the risk of injury.

10 Prior to the use of insertion tools, make sure that all

protective devices are properly fastened.

11 Prior to use, make sure that the insertion tool meets

the technical requirements of this electric tool and is

properly fastened.

12 Only use the supplied saw blade for cutting wood,

never for the processing of metals.

13 Warning! Never use the saw to cut other than the

determined materials.

14 Only use the saw if the protective devices are functio-

nal, in good condition and in the intended position.

15 Ensure that the workpiece is always clamped at the

saw table.

16 Before each sawing operation, make sure that the

machine is secure.

Attention: Laser radiation

Do not stare into the beam

Class 2 laser

Protect yourself and you environment from

accidents using suitable precautionary

measures!

• Do not look directly into the laser beam with unprotected

eyes.

• Never look into the path of the beam.

• Never point the laser beam towards reﬂecting surfaces

and persons or animals. Even a laser beam with a low

output can cause damage to the eyes.

• Caution - methods other than those speciﬁed here can

result in dangerous radiation exposure.

• Never open the laser module. Unexpected exposure to

the beam can occur.

• If the mitre saw is not used for an extended period of

time, the batteries should be removed.

• The laser may not be replaced with a diﬀerent type of laser.

• Repairs of the laser may only be carried out by the laser

manufacturer or an authorised representative.

Safety instructions for handling batteries

1 Always make sure that the batteries are inserted with

the correct polarity (+ and –), as indicated on the

battery.

2 Do not short-circuit batteries.

3 Do not charge non-rechargeable batteries.

4 Do not overcharge batteries!

GB

6

5 Do not mix old and new batteries or batteries of dif-

ferent types or manufacturers! Replace an entire set of

batteries at the same time.

6 Immediately remove used batteries from the device and

dispose of them properly! Do not dispose batteries with

household waste. Defective or used batteries must be

recycled according to Directive 2006/66 / EC.

Give back batteries and / or the device has been of-

fered to the collective facilities. About disposal facilities

you can inform by your municipal or city government.

7 Do not allow batteries to heat up!

8 Do not weld or solder directly on batteries!

9 Do not dismantle batteries!

10 Do not allow batteries to deform!

11 Do not throw batteries into ﬁre!

12 Keep batteries out of the reach of children.

13 Do not allow children to replace batteries without

supervision!

14 Do not keep batteries near ﬁre, ovens or other sources

of heat. Do not use batteries in direct sunlight or store

them in vehicles in hot weather.

15 Keep unused batteries in the original packaging

and keep them away from metal objects. Do not mix

unpacked batteries or toss them together! This can

lead to a short-circuit of the battery and thus damage,

burns or even the risk of ﬁre.

16 Remove batteries from the equipment when it will not

be used for an extended period of time, unless it is for

emergencies!

17 NEVER handle batteries that have leaked without

appropriate protection. If the leaked ﬂuid comes into

contact with your skin, the skin in this area should be

rinsed oﬀ under running water immediately. Always

prevent the ﬂuid from coming into contact with the

eyes and mouth. In the event of contact, please seek

immediate medical attention.

18 Clean the battery contacts and corresponding con-

tacts in the device prior to inserting the batteries.

Residual risks

The machine has been built according to the

state of the art and the recognised technical

safety requirements. However, individual

residual risks can arise during operation.

• Health hazard due to electrical power, with the use of

improper electrical connection cables.

• Furthermore, despite all precautions having been met,

some non-obvious residual risks may still remain.

• Residual risks can be minimised if the “Important informa-

tion”, „Additional safety instructions“ and the „Proper

use“ are observed along with the whole of the operating

instructions.

• Do not load the machine unnecessarily: excessive pres-

sure when sawing will quickly damage the saw blade,

which results in reduced output of the machine in the pro-

cessing and in cut precision.

• When cutting plastic material, please always use clamps:

the parts which should be cut must always be ﬁxed be-

tween the clamps.

• Avoid accidental starting of the machine: the operating but-

ton may not be pressed when inserting the plug in an outlet.

• Use the tool that is recommended in this manual. In do-

ing so, your mitre saw provides optimal performance.

• Hands may never enter the processing zone when the

machine is in operation.

• Release the handle button and switch oﬀ the machine

prior to any operations.

Assembly

WARNING! For you own safety, only insert

the mains plug in an outlet when all as-

sembly steps have been completed and you

have read and understood the safety and

operating instructions.

Lift the saw out of the packaging and place it on your work

bench. (Positioning of the saw on the work bench - see the

next page under „POSITIONING / WORK STATION“)

Installation of the dust bag (fig. 2)

• Squeeze together the metal ring on the chip bag (12)

and attach it to the outlet opening in the motor area.

Assembling the work piece clamping de-

vice (fig. 1.1)

• Loosen the locking screw (17) and attach the work piece

clamping device (10) to the left or right of the ﬁxed saw bench.

• Afterwards, retighten the locking screws (17).

Assembling the work piece supports (fig.

1.1 – 1.2)

• Loosen the cross-head screw (14) and guide the work

piece support through the speciﬁed hole on the side of

the ﬁxed saw bench.

• Make sure that the work piece support (15) is also

guided through the two plates (19) on the underneath.

• Afterwards, retighten the cross-head screw (14).

• Repeat this process on the other side.

Assembling the support stand (fig. 1.1 – 1.2)

• Loosen the cross-head screws (18) on the underneath of

the saw and guide the support stand (16) through the

speciﬁed holes on the back of the saw.

• Afterwards, retighten the cross-head screws (18).

Commissioning

Prior to commissioning, observe the safety

instructions in the operating instructions.

REMOVAL FROM THE PACKAGING

Remove the machine from its package, which protects it during

transport, without damaging the package in order to be able to

use it later for transporting the mitre saw for long-term storage.

MOVING

Since the mitre saw is relatively small and light, its location

can be easily changed, even by a single person. After lock-

ing the locking knob (26 - Fig. 4) in the bottom position, lift

the mitre saw by the handle (34 - Fig. 4).

GB

7

TRANSPORT

If the machine must be transported, carry it by the handle

(34 - Fig. 4) and place it in the original packaging in which

it was supplied. In the process, make sure that it is correctly

positioned in the package (see arrows on the package).

If possible, the load should be ﬁxed with ropes or securing

belts in order to prevent shifting during the transport or parts

of the load from falling down.

POSITIONING/WORK STATION

Position the machine on a work bench or on a ﬂat base so

that the machine is supported as stably as possible.

The equipment must be set up where it can stand secure, i.e.

it should be bolted to a workbench, a universal base frame

or similar. When working with the machine, ergonomic fac-

tors must be considered; the ideal height of the work table or

the base is reached when the base surface or the upper work

surface is 90 to 95 cm above the ground. The positioning of

the machine must provide for at least 80 cm of clearance in

all directions and in order to allow for cleaning and repair

work as well as necessary adjustments in observance of

safety conditions and with suﬃcient room to manoeuvre.

CAUTION: Position the machine in a zone which is suit-

able in respect to the environmental conditions and lighting.

Never forget that the general environmental conditions play

an extremely important role in accident prevention.

CONNECTION TO THE POWER SUPPLY

Make sure that the socket is in a good condition. We would

like to remind you that the power supply must be connected

to a magnetic-thermal circuit breaker which protects all lines

from short-circuits and overloading.

Area of application

Intended application possibilities

The machine cuts:

• Wood and materials similar to wood

• Plastic

Unintended application possibilities

The machine is not suitable for:

• Ferritic materials, steel and cast iron, as well as other ma-

terial types which are not listed, particularly food.

• Mitre saw without guard.

• Materials larger than the speciﬁed cutting data:

90°/90°/

120 x 60 mm

90°/45°

80 x 60 mm

45°/90°

120 x 35 mm

45°/45°

80 x 35 mm

Settings

CROSS-CUTTING

ATTENTION: Before carrying out the following adjust-

ments, please check whether the motor of the machine is

switched oﬀ.

Pivoting the table plate (Fig. 2)

The mitre saw can be pivoted left and right with the rotary table.

Exact angle adjustment is possible on the basis of the scale.

The angle can be precisely and quickly adjusted from 0° to

45° with locking positions at 15°, 22.5° and 30°.

To pivot the rotary table, loosen the set screw (21) and

rotate the unit using the handle (20) until the desired angle is

reached. Then secure it with the set screw (21).

Tilt of the saw unit (Fig. 3)

The saw unit can be tilted at an angle of up to 45°.

Loosen the handle (23) on the rear side of the machine and

tilt the unit to the desired angle position according to the

scale. The angle can be set on the basis of the scale (24) us-

ing the pointer (25). Then the handle must be re-tightened.

Working instructions

After you have carried out all the tasks described above, you

can begin working.

ATTENTION: Always keep your hands away from the cut-

ting zone and never attempt to reach in while cutting.

FIXING A WORKPIECE

Clamp the work piece on the work table with the workpiece

clamp (10 - Fig 1) in order to ﬁx it in place.

Cross-cutting (Fig. 1, 1.3, 4)

Attention! For 90° mitre cuts, the moveable stop rail

(27a) must be ﬁxed in the inner position.

• Open the set screw (27b) on the moveable stop rail

(27a) with an Allen key and push the moveable stop rail

(27a) inwards.

• The moveable stop rail (27a) must be locked in a posi-

tion far enough from the inner position that the distance

between the stop rail (27a) and the saw blade (5) is no

more than 8 mm.

• Before making the cut, check that no collision could occur

between the stop rail (27a) and the saw blade (5).

• Secure the locking lever (27b) again.

• Pressing the machine head lightly downwards and removing

the locking bolt (26) from the motor bracket at the same time

disengages the saw from the lowest position. Swing the ma-

chine head up until the release lever (3) latches into place.

• Lift the saw unit by the handle (2) until it locks in place in

the top position.

• Lock the material with the clamping device (10) on the

ﬁxed saw table to prevent the material from moving dur-

ing the cutting operation.

• Press the workpiece evenly on the stop strips (27); make sure that

you hand remains outside the cutting area of the saw blade.

• With your right hand on the handle (2), press the locking le-

ver (3) so that the unit can also be pivoted downward.

• The motor starts when the start button (1) is pressed.

• Slowly bring the saw blade down to the workpiece and

cut through it with moderate pressure.

• When the cutting operation is completed, move the ma-

chine head back to its upper (home) position and release

the ON/OFF button (1).

GB

8

Attention! The machine executes an upward stroke automati-

cally due to the return spring, i.e. do not release the handle (2)

after completing the cut; instead allow the machine head to

move upwards slowly whilst applying light counter pressure.

Mitre cut 0°- 45° (Fig. 1, 1.3, 3)

The crosscut saw can be used to make mitre cuts of 0° -

45° in relation to the work face.

Important! To make miter cuts (inclined saw head), the

adjustable stop rail (27a) must be ﬁxed at the outer position.

• Open the set screw (27b) for the adjustable stop rail

(27a) with an Allen key and push the adjustable stop rail

outwards.

• The adjustable stop rail (27a) must be ﬁxed far enough in

front of the innermost position that the distance between

the stop rail (27a) and the saw blade (5) amounts to a

maximum of 8 mm.

• Before making a cut, check that the stop rail (27a) and

the saw blade (5) cannot collide.

• Secure the locking lever (27b) again.

• Move the machine head to the top position.

• Fix the rotary table (9) in the 0° position.

• Loosen the set screw (23) and use the handle (2) to angle

the machine head to the left, until the pointer (25) indi-

cates the desired angle measurement on the scale (24).

• Re-tighten the ﬁxing screw (23).

• Cut as described in section “Cross-cutting”.

Mitre cut 0°- 45° and turntable 0°- 45°

The crosscut saw can be used to make mitre cuts to the left

of 0°- 45° in relation to the work face and, at the same

time, 0° - 45° to the left or 0° - 45° to the right in relation

to the stop rail (double mitre cut).

Important! To make miter cuts (inclined saw head), the

adjustable stop rail (27a) must be ﬁxed at the outer position.

• Open the set screw (27b) for the adjustable stop rail

(27a) with an Allen key and push the adjustable stop rail

outwards.

• The adjustable stop rail (27a) must be ﬁxed far enough in

front of the innermost position that the distance between

the stop rail (27a) and the saw blade (5) amounts to a

maximum of 8 mm.

• Before making a cut, check that the stop rail (27a) and

the saw blade (5) cannot collide.

• Secure the locking lever (27b) again.

• Move the machine head to its upper position.

• Release the rotary table (9) by loosening the set screw (23).

• Using the handle (2), set the rotary table (9) to the desired angle.

• Retighten the set screw (23) in order to secure the rotary table.

• Undo the locking screw (23) and use the handle (2) to

tilt the machine head to the left until it coincides with the

required angle value.

• Retighten the ﬁxing screw (23).

• Cut as described in section “Cross-cutting”.

•

Saw blade replacement (Fig. 5)

• Pull out the mains plug.

• Place the saw unit in „cross-cutting“ position

• Unlock the moving saw blade guard (6) by pressing the

locking lever (3 - Fig. 1); in the process, raise the saw

blade guard so that the saw blade is free.

• Actuate the spindle lock (22 - Fig. 3).

• Loosen the saw blade fastening screw (28) - (Atten-

tion: left-handed thread).

• Remove the screw (28) and saw blade ﬂange (29).

• Carefully remove the saw blade (risk of injury from the

saw blade teeth).

• Place a new saw blade on the inner saw blade ﬂange. In the

process, observe the rotational direction of the saw blade.

• Fit the outer saw blade ﬂange and ﬁrmly tighten the screw.

• Move the saw blade guard back to the correct position.

Replacing laser batteries (Fig. 6)

• Remove the laser battery cover (30). Remove the 2 batteries.

• Replace both batteries with the same or an equivalent

type. Make sure that they are inserted with the same po-

larity as the used batteries.

• Close the battery cover.

Switch ON / switch OFF the laser (Fig. 6)

To switch on: Move the ON/OFF (33) switch of the

laser (34) to the “1” position. A laser line is projected onto

the material you wish to process, providing an exact guide

for the cut.

To switch off: Move the ON/OFF switch of the laser

to the “0” position.

Adjusting the laser (Fig. 7)

If the laser (31) ceases to indicate the correct cutting line, you

can readjust the laser. To do so, open the screws (32) and set

the laser by moving sideways to that the laser beam strikes the

teeth of the saw blade (5).

Electrical connection

The electrical motor installed is connected

and ready for operation. The connection

complies with the applicable VDE and DIN

provisions. The customer‘s mains connec-

tion as well as the extension cable used

must also comply with these regulations.

Important information

In the event of an overloading the motor will switch itself

oﬀ. After a cool-down period (time varies) the motor can

be switched back on again.

Damaged electrical connection cable

The insulation on electrical connection cables is often damaged.

This may have the following causes:

• Passage points, where connection cables are passed

through windows or doors.

• Kinks where the connection cable has been improperly

fastened or routed.

• Places where the connection cables have been cut due

to being driven over.

• Insulation damage due to being ripped out of the wall outlet.

• Cracks due to the insulation ageing.

GB

9

• In the event of service work, personal protective equip-

ment must always be work (protective goggles and

gloves).

• Remove saw dust and chips regularly by cleaning the

cutting zone and support surfaces.

We recommend using a suction tool or brush.

ATTENTION: Do not use compressed air!

Check the saw blade from time to time: If problems arise

with the blade, it must be ground by a specialist or re-

placed, depending on the condition.

DECOMMISSIONING OF THE MACHINE

After the machine is decommissioned it can be disposed of

with normal industrial waste.

Disposal

The packaging is wholly composed of

environmentally-friendly materials that can

be disposed of at a local recycling centre.

Contact your local refuse disposal authority

for more details of how to dispose of your

worn out electrical devices.

Such damaged electrical connection cables must not be used

and are life-threatening due to the insulation damage.

Check the electrical connection cables for damage regu-

larly. Make sure that the connection cable does not hang

on the power network during the inspection.

Electrical connection cables must comply with the applica-

ble VDE and DIN provisions. Only use connection cables

with the marking „H 07 RN“.

The printing of the type designation on the connection ca-

ble is mandatory.

AC motor

• The mains voltage must be 230 V

~

• Extension cables up to 25 m long must have a cross-sec-

tion of 1.5 mm

2

.

Connections and repairs of electrical equipment

may only be carried out by an electrician.

Please provide the following information in the event of any

enquiries:

• Type of current for the motor

• Machine data - type plate

Accessories

SAW DUST EXTRACTION

The mitre saw is equipped with an extraction port to which

an extraction system can be connected. Alternatively, a dust

bag can also be attached.

The hose of the extraction system is fastened on the extrac-

tion port with a clamp. We recommend emptying the bag or

container from time to time and cleaning the ﬁlter.

The air speed of the suction system must be at least 30

metres per second.

Maintenance

If personnel qualified for unusual mainte-

nance tasks or repairs must be obtained

during of after the warranty period, please

always contact a service point recommend-

ed by us or contact the manufacturer.

m Warning! Prior to any adjustment, maintenance or

service work disconnect the mains power plug!

• Only perform repair, maintenance and cleaning work

as well as the correction of malfunctions with the drive

switched oﬀ as a basic rule.

• All protective and safety equipment must be reassembled

immediately after repair, maintenance is completed.

NORMAL SERVICE TASKS

Normal service tasks can also be performed by untrained

personnel and are all described in the preceding sections

and in this chapter.

• The mitre saw must not be lubricated, because it always

cuts dry surfaces; all moving machine parts are self-

lubricating.

GB

10

Troubleshooting

Fault Possible cause Remedy

Motor does not work. Motor, cable or plug defective, fuses burnt. Arrange for inspection of the machine by a specialist.

Never repair the motor yourself. Danger! Check fuses

and replace as necessary.

The motor starts up slowly

and does not reach

operating speed.

Voltage too low, coils damaged, capacitor burnt. Contact the utility provider to check the voltage. Arrange

for inspection of the motor by a specialist. Arrange for

replacement of the capacitor by a specialist.

Motor makes excessive

noise.

Coils damaged, motor defective. Arrange for inspection of the motor by a specialist.

The motor does not reach

its full power.

Circuits in the network are overloaded (lamps,

other motors, etc.).

Do not use any other equipment or motors on the same

circuit.

Motor overheats easily. Overloading of the motor, insufficient cooling of

the motor.

Avoid overloading the motor while cutting, remove dust

from the motor in order to ensure optimal cooling of the

motor.

Reduced cutting power

when sawing.

Saw blade too small (ground too much). Readjust end stop of the saw unit.

Saw cut is rough or wavy. Saw blade dull, tooth shape not appropriate for

the material thickness.

Resharpen saw blade and/or use suitable saw blade.

Workpiece pulls away

and/or splinters.

Excessive cutting pressure and/or saw blade not

suitable for use.

Insert suitable saw blade.

GB

11

GUARANTEE CERTIFICATE

Dear Customer,

All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device

develops a fault, please contact our service department at the address shown on this guarantee card. Of course, if you would prefer to

call us then we are also happy to oﬀer our assistance under the service number printed below. Please note the following terms under which

guarantee claims can be made:

• These guarantee terms cover additional guarantee rights and do not aﬀect your statutory warranty rights. We do not charge you for this

guarantee.

• Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the rectiﬁcation of these defects

or replacement of the device. Please note that our devices have not been designed for use in commercial, trade or industrial applica-

tions. Consequently, the guarantee is invalidated if the equipment is used in commercial, trade or industrial applications or for other

equivalent activities. The following are also excluded from our guarantee: compensation for transport damage, damage caused by

failure to comply with the installation/assembly instructions or damage caused by unprofessional installation, failure to comply with the

operating instructions (e.g. connection to the wrong mains voltage or current type), misuse or inappropriate use (such as overloading

of the device or use of non-approved tools or accessories), failure to comply with the maintenance and safety regulations, ingress of

foreign bodies into the device (e.g. sand, stones or dust), eﬀects of force or external inﬂuences (e.g. damage caused by the device being

dropped) and normal wear resulting from proper operation of the device.

The guarantee is rendered null and void if any attempt is made to tamper with the device.

• The guarantee is valid for a period of 3 years starting from the purchase date of the device. Guarantee claims should be submitted

before the end of the guarantee period within two weeks of the defect being noticed. No guarantee claims will be accepted after the

end of the guarantee period. The original guarantee period remains applicable to the device even if repairs are carried out or parts are

replaced. In such cases, the work performed or parts ﬁtted will not result in an extension of the guarantee period, and no new guarantee

will become active for the work performed or parts ﬁtted. This also applies when an on-site service is used.

• In order to assert your guarantee claim, please send your defective device postage-free to the address shown below. Please enclose

either the original or a copy of your sales receipt or another dated proof of purchase. Please keep your sales receipt in a safe place, as

it is your proof of purchase. It would help us if you could describe the nature of the problem in as much detail as possible. If the defect is

covered by our guarantee then your device will either be repaired immediately and returned to you, or we will send you a new device.

Of course, we are also happy oﬀer a chargeable repair service for any defects which are not covered by the scope of this guarantee or for

units which are no longer covered. To take advantage of this service, please send the device to our service address.

HU

12

Tartalomjegyzék: Oldal:

Bevezetés 13

Rendeltetésszerűi használat 14

Fontos utasítások 14

További biztonsági utasítások 16

Maradék kockázatok 18

Üzembe helyezés 18

Összeszerelés 18

Alkalmazási terület 19

Beállítások 19

Munkavégzési útmutatások 19

Elektromos csatlakoztatás 21

Tar tozék 21

Javítás 21

Mentesítés 21

Hibaelhárítás 22

Jótállási tájékoztató 23

Konformkijelentés 72

HU

13

Bevezetés

GYÁRTÓ:

scheppach

Fabrikation von Holzbearbeitungsmaschine GmbH

Günzburger Straße 69

D-89335 Ichenhausen

KEDVES VÁSÁRLÓ!

A hatályban lévő termékfelelősségi törvény értel-

mében a berendezés gyártója nem vonható fele-

lősségre a berendezésen vagy vele kapcsolatban

keletkező károkért a következő esetekben:

• szakszerűtlen kezelés,

• a használati utasítások be nem tartása,

• harmadik személy által végzett, szakképzetlen

javítások,

• nem eredeti alkatrészek beszerelése és cseréje,

• szakszerűtlen használat,

• az elektromos rendszer kiesése az elektromos

előírások, illetve a VDE 0100, DIN 57113 / VDE

0113 szabályozások be nem tartása miatt.

JAVASLATOK:

Mielőtt a berendezést összeszerelné, és üzembe

helyezné olvassa el a használati útmutató teljes

szövegét.

Az üzemelési utasítások célja a készülékkel való

ismerkedésének megkönnyítése és a használati

lehetőségeinek megismertetése.

Az üzemelési utasítások fontos megjegyzéseket tar-

talmaz a készülék biztonságos, szakszerű és gaz-

daságos használatával kapcsolatosan, a veszélyek

elkerülésére, a javítási költségek megspórolására, a

kiesési idő csökkentésére, és a készülék megbízha-

tóságának és élettartamának növelésére.

A használati útmutatóba foglalt biztonsági utasítá-

sokon kívül mindenképpen be kell tartani a nemzeti

érvényben lévő szabályozásokat a készülék üzeme-

lésével kapcsolatosan.

Az üzemelési utasításokat helyezze egy tiszta, mű-

anyag mappába, hogy megóvja a szennyeződéstől

és a nedvességtől, és tárolja a készülék közelében.

A munka elkezdése előtt minden gépkezelőnek el

kell olvasnia az utasításokat és gondosan be kell

tartania őket. Csak olyan személyek használhatják

a készüléket, akiket kiképeztek a gép használatáról,

és a lehetséges veszélyekről, illetve kockázatokról.

Be kell tartani az előírt minimális kort.

A jelen üzemelési utasításokba foglalt biztonsági

előírások és a helyi országos különleges előírások

kiegészítéseként be kell tartani az általánosan elis-

mert műszaki előírásokat a fafeldolgozó szerszám-

gépek üzemelésekor.

Az útmutató, valamint a biztonsági előírások gyel-

men kívül hagyásából származó balesetekért és

károkért nem vállalunk felelősséget.

1. ábra jelmagyarázata

1 Indítógomb

2 Fogantyú

3 Zárókar

4 Motor

5 Fűrészlap

6 Mozgatható fűrészlapvédő

7 Lábazat

8 Asztalbetét

9 Forgóasztal

10 Szerszám befogó

11 Ház/lábazat csukló

12 Forgácsgyűjtő zsák

13 Merev fűrészlapvédő

PKS 1500 A2

Szállított elemek

Fejező- és gérvágó

fűrész

Forgácsgyűjtő zsák

Szerszám befogó

fűrészlapcsere

szerszáma -

Imbuszkulccsal 6 mm

Imbuszkulccsal 3 mm

- oldja ki a eltolható

ütközősín

2 munkadarabtartó

Álló fogó

2 szénkefe

2 elem (AAA)

Kezelési útmutató

Műszaki adatok

Méretek, H x Sz x M 690 x 550 x 440

ø forgóasztal, mm 385 x 150

Asztalmagasság, mm 55

Fűrészlap ø, mm 210/30/2,6/1,6 WZ 48

Fordulatszám, 1/perc 5000

Vágási sebesség, m/s 55

Forgási tartomány 2 x 45°

Dőlésszög 45°

Dupla gérvágás 45° x

45°

bal

Raszterhelyzetek

45°, 30°, 22,5°, 15°, 0°,

15°, 22,5°, 30°, 45°

Súly, kg 7,7

Fejező üzem vágási adatai

legnagyobb vágási

mélység 90°/45°

60 / 35 mm

90°/90° 120 x 60 mm

90°/45° 80 x 60 mm

45°/90° 120 x 35 mm

45°/45° 80 x 35 mm

Meghajtás

Motor V~/Hz 220-240 / 50

Teljesítményfelvétel, W

S1 1200W

S6 25%* 1500W

A műszaki változtatások jogát fenntartjuk!

HU

14

* S6 üzemmód, megszakítás nélküli, időszakos

üzemmód. Az üzemeltetés indítási időből, folya-

matos terhelés alatt állás időszakából és üresjárati

időből áll. A működési idő 10 perc, a relatív bekap-

csolási idő pedig a működési idő 25%-a.

A munkadarabnak legalább 3 mm magasnak és

10 mm szélesnek kell lennie.

Ügyeljen arra, hogy a munkadarabot a befogó

szerkezettel mindig biztosítsa.

Zajképződésre vonatkozó információk

A gép zajszintje működés közben az alábbi értékek

szerint alakul:

L

pA

: 99.6dB(A) K=3dB(A)

L

wA

: 112.6dB(A) K=3dB(A)

Figyelmeztetés: A zaj súlyosan károsíthatja egész-

ségét. Ha a gép által keltett zaj meghaladja a 85 dB

(A) értéket, akkor viseljen egy megfelelő hallásvédőt.

Ha hibás az elektromos csatlakozó, a gép indítá-

sánál az áram lecsökkenhet. Ez más gépeket is

befolyásolhat (pl. villogó lámpák). Ha az elektromos

teljesítmény értéke Zmax < 0,27, ilyen jellegű zava-

rokra nem kell számítani (ha mégis, akkor értesítse

a készülék szállítóját).

• A megadott rezgés kibocsátási értékét szabvá-

nyosított hitelesítési eljárás során mértük meg,

és segítségével az elektromos kéziszerszámok

összehasonlíthatók egymással;

• A megadott rezgés kibocsátási értéke a terhelés

első megítélésére is használható.

Rendeltetésszerűi használat

A fejezőfűrész a gép nagyságának megfelelő, fa

és műanyag levágására szolgál. A fűrész nem al-

kalmas

a tüzelőfa vágására.

Figyelmeztetés! A tartozék fűrészlap kizárólag fa

fűrészelésére alkalmas! Ne használja műanyag fű-

részelésére!

A gépet csak rendeltetése szerint szabad használ-

ni. Ezt túlhaladó bármilyen használat, nem számít

rendeltetésszerűnek. Ebből adódó bármilyen kárért

vagy bármilyen fajta sérülésért a használó ill. a ke-

zelő felelős és nem a gyártó.

Csak a gepnek megfelelő fűreszlapokat sza-

bad hasznalni. Tilos barmilyen fajta szetvalaszto

tarcsanak a hasznalata. A rendeltetesszerűi

hasznalat resze a biztonsagi utasitasok gye-

lembe vetele is, valamint az osszeszerelesi

es a hasznalati utasitasban levő uzemeltetesi

utasitasok.

A gepet kezelő es karbantarto szemelyeknek ezek-

ben jartasaknak es a lehetseges veszelyekkel

kapcsolatban kioktatottaknak kell lenniuk. Ezen

kivul legpontosabban be kell tartani az ervenyes

balesetvedelmi előirasokat.

Figyelembe kell venni a munkaegeszsegugyi es a

biztonsagtechnikai teren fennallo balesetvedelmi

szabalyokat.

A gepen tortenő valtoztatasok, teljesen kizarjak

a gyarto szavatolasat es az ebből adodo ka-

rok megteriteset. Bizonyos fennmaradt

rizikotenyezőket rendeltetesszerű hasznalat

ellenere sem lehet teljes mertekben kizarni. A gep

konstrukcioja es felepitese altal a kovetkező pontok

lephetnek fel:

• A fűreszlap megerintese a nem lefedett

fűreszkorben.

• A forgo fűreszlapba valo nyulas (vagasi serules)

• A munkadarabok es munkadarabreszek

visszacsapodasa.

• Fűreszlaptoresek.

• A fűreszlap hibas kemenyfemreszeinek a

kivetese.

• A szukseges zajcsokkentő fullvedő

hasznalatanak mellőzesekor a hallas

karosodasa.

• Zart teremben torteno hasznalatkor az

egeszsegre karos fapor kibocsajtasa.

Kerjuk vegye gyelembe, hogy a keszulekeink

rendeltetesuk szerint nem az ipari, kezműipari vagy

gyari hasznalatra lettek konstrualva. Nem vallalunk

szavatossagot, ha a keszulek ipari, kezműipari

vagy gyari uzemek teruleten valamint egyenertekű

tevekenysegek teruleten van hasznalva.

Fontos utasítások

Figyelem! Az elektromos kéziszerszámok haszná-

lata során az áramütés, illetve sérülés- és tűzve-

szély megelőzése érdekében az alábbi alapvető

biztonsági utasításokat kell betartani. Az elektro-

mos kéziszerszám használata előtt minden utasí-

tást olvasson el, és mindig gondosan tartsa be a

biztonsági előírásokat.

Biztonságos munkavégzés

1 Tartsa a munkakörét rendben

– Rendetlenség a munkakörben baleset veszé-

lyét idézi elő.

2 Vegye a környezeti befolyásokat gyelembe

– Ne tegyen ki az elektromos szerszámokat

esőnek.

– Ne használjon elektromos szerszámokat ned-

ves vagy vizes környezetben.

– Gondoskodjon jó megvilágításról.

– Ne használjon elektromos eszközöket ott,

ahol tűz- és robbanásveszély keletkezhet.

3 Óvja magát az áramütés elől

– Kerülje el a földelt részekkel való testi érint-

kezést, mint például csövekkel, fűtőtestekkel,

tűzhelyekkel,hűtőszekrényekkel.

4 Tartsa a gyerekeket távol!

– Ne engedje meg más személynek, hogy meg-

érintsék a szerszámot vagy a kábelt, tartsa

őket a munkakörétől távol.

HU

15

– A gépet 18 év feletti személyek kezelhetik, 16

év feletti tanulók pedig kizárólag felügyelet

mellett.

5 Tárolja a szerszámait biztonságosan

– Nem használt szerszámokat egy száraz, zárt

teremben és a gyerekek számára nem elérhe-

tően kell tárolni.

6 Ne terhelje túl a szerszámait

– Jobban és biztonságosabban dolgozik a meg-

adott teljesítményi körben.

7 Használja a kellő szerszámot

– Ne használjon túl gyenge szerszámokat vagy

kiegészítő egységeket nehéz munkákra.

– Ne használja a szerszámokat olyan célokra és

munkákra, melyekre ezek nincsenek előrelát-

va; mint például ne használjon kézi körfűré-

szeket fák kivágására vagy ágak levágására.

– Ne használja az elektromos kéziszerszámot

tűzifa fűrészelésére.

8 Viseljen megfelelő munkaruhát

– Ne viseljen bő ruhát vagy ékszert. Ezeket

elkaphatják a mozgó részek.

A szabadban történö munkálatoknál gumi-

kesztyű és tapadós lábbeli ajánlatos.

– Hosszú hajnál viseljen hajhálót.

9 Használjon védőfelszerelést

– - Viseljen védőszemüveget.

– - Viseljen légzőmaszkot, ha a munka során

por keletkezik.

10 Csatlakoztassa rá a porelszívóberendezést

– Ha a porelszívási berendezésekhez csatla-

kozások vannak, akkor győződjön meg arról,

hogy ezek rá is vannak kapcsolva és hasz-

nálva is vannak.

– A készüléket zárt térben csak megfelelő

elszívó berendezés mellett működtetheti.

11 Ne használja fel a kábelt más célokra

– Ne hordja a szerszámot a kábelnál fogva, és

ne használja fel a kábelt a csatlakozó dugó

kihúzására a dugaszoló aljzatból. Óvja a

kábelt hőségtől, olajtól és éles szélektől.

12 Biztosítsa a munkadarabot

– Használjon szorítószerkezeteket vagy egy

satut a munkadarab befogására. Ezáltal ez

biztosabban van rögzítve mint kézzel és lehe-

tővé teszi a gép mindkét kézzeli kezelését.

– Hosszú munkadaraboknál egy kiegészítő

támasztékra (asztal, bakok stb.) van szükség

ahhoz, hogy a gép ne dőljön fel.

– A munkadarabot mindig erősen nyomja a

munkalapra és az ütközőhöz, hogy ne billeg-

jen és ne forduljon el.

13 Kerülje a rendellenes testtartást

– Biztosan álljon és mindig őrizze meg egyen-

súlyát.

– Ne tartsa a kezét olyan ügyetlen helyzetek-

ben, amelyek esetén hirtelen megcsúszás

miatt egyik vagy mindkét keze hozzáérhet a

fűrészlaphoz.

14 Ápolja gondosan a szerszámait

– Tartsa a szerszámait élesen és tisztán, hogy

jól és biztosan tudjon dolgozni.

– Kövesse a karbantartási előírásokat és az

utasításokat a szerszámcserére.

– Ellenőrizze le rendszeresen a csatlakozási

vezetéket és a kábelját, és sérülés esetén

cseréltesse ki azt egy elismert szakember

által.

– Ellenőrizze le rendszeresen a hosszabbító

kábelt és sérülés esetén cserélje ki.

– Tartsa a fogantyúkat szárazon valamint olaj

és zsír mentesen.

15 Húzza ki a csatlakozódugót az aljzatból

– A laza szilánkokat, forgácsot vagy beszoruló

fadarabokat soha ne próbálja meg a fűrész-

lap mozgása közben kiszedni.

– Ha nem használja az elektromos kéziszer-

számot, javítás előtt és a szerszámok, pl.

fűrészlap, fúró és marógép cseréjénél.

16 Ne hagyjon benne semmilyen szerszámkulcsot

dugva

– Bekapcsolás előtt ellenőrizze le, hogy a

kulcsok és a beállító szerszámok el vannake

távolítva.

17 Ügyeljen arra, hogy a gép ne indulhasson el

akaratlanul

– Mielőtt a csatlakozót bedugja az aljzatba,

győződjön meg arról, hogy a gép kapcsolója

kikapcsolt állapotban van.

18 Kültéren használjon hosszabbító kábelt

– A szabadban csak szabadtéri használatra

alkalmas, ennek megfelelő jelöléssel ellátott

hosszabbító kábelt alkalmazzon.

– A kábeldobot csak letekert állapotban hasz-

nálja.

19 Legyen gyelmes

– Figyeljen arra, amit csinál. Munkája során

kellő körültekintéssel járjon el. Ne használja

az elektromos kéziszerszámot, ha nem tud rá

gyelni.

20 Ellenőrizze le a készülékét sérülésekre

– A szerszám további használata előtt a védő

berendezéseket vagy enyhén sérült részeket

gondosan megvizsgálni, hibátlan és megha-

tározásuknak megfelelő működésükre.

– Vizsgálja meg, hogy a mozgó részek műkö-

dése rendben van, és hogy nem szorulnak

vagy nincsennek károsulva részeik. Ahhoz,

hogy a készülék biztonsága biztosítva legyen

minden résznek helyesen fel kell szerelve

lennie.

– A mozgatható védőfedelet nyitott állapotban

nem szabad beszorítani.

– Amennyiben a használati utasításban nincs

más megadva, a károsult biztonsági beren-

dezéseket és részeket szakszerüen egy

elismert szakműhely által kell megjavíttatni

vagy kicseréltetni.

– A károsult kapcsolókat egy vevőszolgálati

műhely által muszáj kicseréltetni.

Stránka sa načítava ...

Parkside PKS 1500 A2 Operating And Safety Instructions Manual

Táto príručka je tiež vhodná pre

Parkside PKS 1500 A2 Operating And Safety Instructions Manual

V iných jazykoch

Súvisiace články

Ďalšie dokumenty