Parkside PTK 2000 A1 Návod na používanie

Značka: Parkside

Model: PTK 2000 A1

Typ: Návod na používanie

IAN 104416

TABLE SAW PTK 2000 A1

SIHU

FŰRÉSZASZTAL PTK 2000 A1

Kezelési és biztonsági útmutató

Az eredeti használati útmutató fordítása

NAMIZNA KROŽNA ŽAGA PTK 2000 A1

Napotki za upravljanje in varnost

Prevod originalnih navodil za uporabo

TISCHKREISSÄGE PTK 2000 A1

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung

DE AT CH

TABLE SAW PTK 2000 A1

Operating and Safety Instructions

Translation of Original Operating Manual

STOLOVÁ KOTOUČOVÁ PILA PTK 2000 A1

Pokyny k obsluze a bezpečnostní pokyny

Překlad originálního návodu k obsluze

STOLOVÁ KOTÚČOVÁ PÍLA PTK 2000 A1

Upozornenia k obsluhe a bezpečnostné upozornenia

Preklad originálu návodu na obsluhu

SKCZ

Table Saw

04-15

Fűrészasztal

16-29

Namizna krožna žaga

30-41

Stolová kotoučová pila

42-54

Stolová kotúčová píla

55-67

DE | AT | CH

Tischkreissäge

68-81

TABLE SAW PTK 2000 A1

2 3 4 5 6 7

1617

11 8 9

18 g a b

21 22 23 24 S t

20 19

22 21

14 14

25 26

agc

c a

g b

max. 3-5 mm

r s

e f 7 f

k j12

45°

12 5

26.1

11 8 9 9.1

34 35 36 37

o o

33p

f f

z y z

32a

32b

39 40

41 42

3643

Table of contents:

Page:

Introduction 6

Device description 6

Scope of delivery 6-7

Intended use 7

Safety information 7-10

Technical data 10

Before starting the equipment 10

Attachment 10-11

Using the saw 12-13

10.

Operation 13-14

11.

Transport 14

12.

Maintenance 14

13.

Storage 14

14.

Electrical connection 14

15.

Disposal and recycling 14

16.

Troubleshooting 15

17.

Warranty certicate 15

18.

Declaration of conformity 82

Caution - Read the operating instructions to reduce the risk of inquiry

Wear safety goggles!

Wear ear-muffs!

Wear a breathing mask!

Explanation of the symbols on the equipment

Warning! Danger to life, risk of injury or damage to the tool are possible by ignoring!.

Important! Risk of injury. Never reach into the running saw blade!

Important! Laser radiation

Wear protective gloves

1. Introduction

MANUFACTURER:

scheppach

Fabrikation von Holzbearbeitungsmaschine GmbH

Günzburger Straße 69

D-89335 Ichenhausen

DEAR CUSTOMER,

We hope your new tool brings you much enjoyment and

success.

NOTE:

According to the applicable product liability laws, the

manufacturer of the device does not assume liability

for damages to the product or damages caused by the

product that occurs due to:

• Improper handling,

• Non-compliance of the operating instructions,

• Repairs by third parties, not by authorized service

technicians,

• Installation and replacement of non-original spare

parts,

• Application other than specied,

• A breakdown of the electrical system that occurs due

to the non-compliance of the electric regulations and

VDE regulations 0100, DIN 57113 / VDE0113.

WE RECOMMEND:

Read through the complete text in the operating instruc-

tions before installing and commissioning the device.

The operating instructions are intended to help the user

to become familiar with the machine and take advan-

tage of its application possibilities in accordance with the

recommendations. The operating instructions contain

important information on how to operate the machine

safely, professionally and economically, how to avoid

danger, costly repairs, reduce downtimes and how to in-

crease reliability and service life of the machine.

In addition to the safety regulations in the operating

instructions, you have to meet the applicable regula-

tions that apply for the operation of the machine in your

country. Keep the operating instructions package with

the machine at all times and store it in a plastic cover

to protect it from dirt and moisture. Read the instruction

manual each time before operating the machine and

carefully follow its information. The machine can only be

operated by persons who were instructed concerning the

operation of the machine and who are informed about

the associated dangers. The minimum age requirement

must be complied with. In addition to the safety require-

ments in these operating instructions and your country’s

applicable regulations, you should observe the generally

recognized technical rules concerning the operation of

woodworking machines.

2. Layout

(Fig.1/2/4/9-10/16-18/20/28/31)

1. Saw bench

2. Saw blade guard

3. Extraction hose

4. Splitter

5. Saw blade

6. Table insert

7. Parallel stop

8. Hand wheel

9. Adjusting and locking grip

10. Base frame

11. ON/OFF switch

12. Chain bar

13. Cross stop

14. Bench width extension

15. Bench length extension

16. Extractor adapter

17. Push stick

18. Legs

19. Cross struts

20. Longitudinal struts

21. Center struts, short

22. Center struts, long

23. Rubber legs

24. Stability bar

25. Table support, short

26. Table support, long

27. Screw with wing nut

28. Oval hole in splitter

29. Countersunk head screws

30. Fixing screw

31. Eccentric lever

32. Groove

33. Knurled screw

34. Laser

35. Laser switch

36. Screws for battery compartment

37. Battery cover

38. /39. Fixing points

3. Scope of delivery

• Open the packaging and remove the device care-

fully.

• Remove the packaging material as well as the pack-

aging and transport bracing (if available).

• Check that the delivery is complete.

• Check the device and accessory parts for transport

damage.

• If possible, store the packaging until the warranty

period has expired.

ATTENTION

The device and packaging materials are not toys!

Children must not be allowed to play with plastic

bags, lm and small parts! There is a risk of swal-

lowing and suffocation!

• Original operating instructions

• Saw table to preassembled,

- carbide-tipped saw blade with 24 teeth

• Carbide-tipped saw blade with 48 teeth

• Saw blade guard

• Extraction hose

• Splitter with laser

• Batteries 1.5 V AAA (2x)

• Parallel stop

• Stop rail

• Cross stop

• Table width extension (2x)

• Table length extension

• Push stick

• Legs (4x)

• Cross struts (2x)

• Longitudinal struts (2x)

• Center struts, short (2x)

• Center struts, long (2x)

• Rubber feet (4x)

• Stability bar (2x)

• Table support, short (4x)

• Table support, long (2x)

Installation material

a) Washer (58x)

b) Nut (38x)

c) Hex screw (30x)

d) Phillips head screw (4x)

g) Retaining ring (58)

n) Round head screw M6x12 (24x)

m) Round head screw M6x16 (4x)

Tools

r) Open-ended wrench, size 22

s) Ring wrench, size 10/24

t) Open-ended wrench, size 8/10

4. Intended use

The bench-type circular saw is designed for the slitting

and cross-cutting of all types of timber, commensurate

with the machine’s size.

The machine is not to be used for cutting any type of

roundwood.

The machine is to be used only for its prescribed pur-

pose. Any use other than that mentioned is considered

to be a case of misuse. The user/operator and not the

manufacturer shall be liable for any damage or injury

resulting such cases of misuse.

The machine is to be operated only with suitable saw

blades. It is prohibited to use any type of cutting-off

wheel. To use the machine properly you must also

observe the safety regulations, the assembly instruc-

tions and the operating instructions to be found in this

manual. All persons who use and service the machine

have to be acquainted with this manual and must be

informed about its potential hazards. It is also imperative

to observe the accident prevention regulations in force

in your area. The same applies for the general rules of

occupational health and safety.

m Important!

When using the equipment, a few safety precautions

must be observed to avoid injuries and damage. Please

read the complete operating instructions and safety

regulations with due care. Keep this manual in a safe

place, so that the information is available at all times.

If you give the equipment to any other person, hand

over these operating instructions and safety regulations

as well. We cannot accept any liability for damage or

accidents which arise due to a failure to follow these

instructions and the safety instructions.

The manufacturer shall not be liable for any changes

made to the machine nor for any damage resulting from

such changes.

Even when the machine is used as prescribed it is still

impossible to eliminate certain residual risk factors.

The following hazards may arise in connection with the

machine’s construction and design:

• Contact with the saw blade in the uncovered saw

zone.

• Reaching into the running saw blade (cut injuries).

• Kick-back of workpieces and parts of workpieces

• Saw blade fracturing.

• Catapulting of faulty carbide tips from the saw blade.

• Damage to hearing if essential ear-muffs are not

worn.

• Harmful emissions of wood dust when the machine is

used in closed rooms.

m Please note that our equipment has not been de-

signed for use in commercial, trade or industrial appli-

cations. Our warranty will be voided if the machine is

used in commercial, trade or industrial businesses or

for equivalent purposes.

5. Safety information

m Attention! The following basic safety measures

must be observed when using electric tools for protec-

tion against electric shock, and the risk of injury and

re. Read all these notices before using the electric

tool and keep the safety instructions for later refer-

ence.

Safe work

1 Keep the work area orderly

– Disorder in the work area can lead to accidents.

2 Take environmental inuences into account

– Do not expose electric tools to rain.

– Do not use electric tools in a damp or wet envi-

ronment.

– Make sure that the work area is well-illuminated.

– Do not use electric tools where there is a risk of

re or explosion.

3 Protect yourself from electric shock

– Avoid physical contact with earthed parts (e.g.

pipes, radiators, electric ranges, cooling units).

4 Keep children away

– Do not allow other persons to touch the equipment

or cable, keep them away from your work area.

5 Securely store unused electric tools

– Unused electric tools should be stored in a dry,

elevated or closed location out of the reach of

children.

6 Do not overload your electric tool

– They work better and more safely in the specied

output range.

7 Use the correct electric tool

– Do not use low-output electric tools for heavy work.

– Do not use the electric tool for purposes for which

it is not intended. For example, do not use hand-

held circular saws for the cutting of branches or

logs.

– Do not use the electric tool to cut rewood.

8 Wear suitable clothing

– Do not wear wide clothing or jewellery, which can

become entangled in moving parts.

– When working outdoors, anti-slip footwear is

recommended.

– Tie long hair back in a hair net.

9 Use protective equipment

– Wear protective goggles.

– Wear a mask when carrying out dust-creating

work.

10 Connect the dust extraction device if you will

be processing wood, materials similar to wood,

or plastics.

– If connections for dust extraction and a collect-

ing device are present, make sure that they are

connected and used properly.

– When processing wood, materials similar to

wood, and plastics. operation in enclosed

spaces is only permitted with the use of a suit-

able extraction system.

11 Secure the workpiece

– Use the clamping devices or a vice to hold the

workpiece in place. In this manner, it is held

more securely than with your hand.

– An additional support is necessary for long work-

pieces (table, trestle, etc.) in order to prevent the

machine from tipping over.

– Always press the workpiece rmly against

the working plate and stop in order to prevent

bouncing and twisting of the workpiece.

12 Avoid abnormal posture

– Make sure that you have secure footing and

always maintain your balance.

– Avoid awkward hand positions in which a sudden

slip could cause one or both hands to come into

contact with the saw blade.

13 Take care of your tools

– Keep cutting tools sharp and clean in order to be

able to work better and more safely.

– Follow the instructions for lubrication and for tool

replacement.

– Check the connection cable of the electric tool

regularly and have it replaced by a recognised

specialist when damaged.

– Check extension cables regularly and replace

them when damaged.

– Keep the handle dry, clean and free of oil and

grease.

14 Pull the plug out of the outlet

– Never remove loose splinters, chips or jammed

wood pieces from the running saw blade.

– During non-use of the electric tool or prior to

maintenance and when replacing tools such as

saw blades, bits, milling heads.

– When the saw blade is blocked due to abnormal

feed force during cutting, turn the machine off

and disconnect it from power supply. Remove

the work piece and ensure that the saw blade

runs free. Turn the machine on and start new

cutting operation with reduced feed force.

15 Do not leave a tool key inserted

– Before switching on, make sure that keys and

adjusting tools are removed.

16 Avoid inadvertent starting

– Make sure that the switch is switched off when

plugging the plug into an outlet.

17 Use extension cables for outdoors

– Only use approved and appropriately identied

extension cables for use outdoors.

– Only use cable reels in the unrolled state.

18 Remain attentive

– Pay attention to what you are doing. Remain

sensible when working. Do not use the electric

tool when you are distracted.

19 Check the electric tool for potential damage

– Protective devices and other parts must be care-

fully inspected to ensure that they are fault-free

and function as intended prior to continued use

of the electric tool.

– Check whether the moving parts function fault-

lessly and do not jam or whether parts are dam-

aged. All parts must be correctly mounted and all

conditions must be fullled to ensure fault-free

operation of the electric tool.

– The moving protective hood may not be xed in

the open position.

– Damaged protective devices and parts must be

properly repaired or replaced by a recognised

workshop, insofar as nothing different is speci-

ed in the operating manual.

– Damaged switches must be replaced at a cus-

tomer service workshop.

– Do not use any faulty or damaged connection

cables.

– Do not use any electric tool on which the switch

cannot be switched on and off.

20 ATTENTION!

– Exercise elevated caution for double mitre cuts.

21 ATTENTION!

– The use of other insertion tools and other acces-

sories can entail a risk of injury.

22 Have your electric tool repaired by a qualied

electrician

– This electric tool conforms to the applicable safety

regulations. Repairs may only be performed by an

electrician using original spare parts. Otherwise

accidents can occur.

23 Do not use the cable for purposes for which it

is not intended

– Do not use the cable to pull the plug out of the

outlet. Protect the cable from heat, oil and sharp

edges.

ADDITIONAL SAFETY INSTRUCTIONS

1 Safety precautions

– Warning! Do not use damaged, cracked or

deformed saw blades.

– Replace a worn table insert.

– Only use saw blades recommended by the

manufacturer which conform to EN 847-1.

m Warning! Keep attention When changing the

saw blade.The cutting width is not smaller and

the main blade thickness of the saw blade is not

greater than the thickness of the gap wedge!

– Make sure that a suitable saw blade for the ma-

terial to be cut is selected.

– Wear suitable personal protective equipment.

This includes:

Hearing protection to avoid the risk of becoming

hearing impaired,

Respiratory protection to avoid the risk of inhal-

ing harmful dust,

– Wear gloves when handling saw blades and

rough materials.

– Carry saw blades in a container whenever practi-

cal.

– Wear goggles. Sparks generated during work or

splinters, chippings and dust coming from the

device can lead to loss of eyesight.

– Connect a dust collecting device to the electric

tool when sawing wood. The emission of dust

is inuenced, among other things, by the type

of material to be processed, the signicance of

local separation (collection or source) and the

correct setting of the hood/guide plates/guides.

– Do not use saw blades made of high-speed alloy

steel (HSS steel).

– In times of non-use keep the push stick or the

push block with the electrical power tool in its

holder at all times.

2 Maintenance and repair

– Pull out the mains plug for any adjustment or

repair tasks.

– The generation of noise is inuenced by various

factors, including the characteristics of saw

blades, condition of saw blade and electric

tool. Use saw blades which were designed for

reduced noise development, insofar as possible.

Maintain the electric tool and tool attachments

regularly and if necessary, initiate repairs in

order to reduce noise.

– Report faults on the electric tool, protective

devices or the tool attachment to the person

responsible for safety as soon as they are dis-

covered.

3 Safe work

– Use the push stick or handle with sliding wood,

to pass the workpiece securely out off the saw

blade.

– Make sure that the riving knife is always used,

and set up is correctly.

– Use the upper blade guard and set it to the cor-

rect position.

– Only use saw blades for which the maximum

permissible speed is not lower than the maxi-

mum spindle speed of table saws and which are

suitable for the material to be cut.

– Do not cut rebates or grooves without tting a

suitable guard, e.g. a tunnel-type guard, over the

saw table.

– Circular saws must not be used for slotting jobs

(cutting grooves which end in the workpiece).

– When transporting the electric tool, only use

the transport devices. Never use the protective

devices for handling or transport.

– Make sure that the upper part of the saw blade

is covered during transport, e.g. by the protective

device.

– Be sure to only use spacers and spindle rings

specied by the manufacturer as suitable for the

intended purpose.

– The oor around the machine must be level,

clean and free of loose particles, such as chips

and cutting residues.

– Always stand to the side of the saw blade when

working with the saw.

– Do not remove any cutting residues or other

parts of workpieces from the cutting zone while

the machine is running and the saw unit is not

at rest.

– Make sure that the machine is always secured

on a workbench or a table if at all possible.

– Support long workpieces (e.g. with a roller table)

to prevent them sagging at the end of a cut.

– m Attention! Never remove loose splinters, chips

or jammed pieces of wood while the saw blade is

running.

• Switch off the machine to troubleshoot or remo-

ve jammed pieces of wood. - Disconnect the

main power plug -

• Retting, including adjusting and measuring

works, and cleaning must be carried out only

when the motor is switched off. - Disconnect

the main power plug -

• Before switching on again, ensure that keys

and adjustment tools have been removed.

Warning! This electric tool generates an electromag-

netic eld during operation. This eld can impair active

or passive medical implants under certain conditions. In

order to prevent the risk of serious or deadly injuries, we

recommend that persons with medical implants consult

with their physician and the manufacturer of the medical

implant prior to operating the electric tool.

SAFETY INSTRUCTIONS FOR THE HANDLING OF

SAW BLADES

1 Only use insertion tools if you have mastered their

use.

2 Observe the maximum speed. The maximum

speed specied on the insertion tool may not be

exceeded. If specied, observe the speed range.

3 Observe the motor / saw blade direction of rota-

tion.

4 Do not use any insertion tools with cracks. Sort out

cracked insertion tools. Repairs are not permitted.

5 Clean grease, oil and water off of the clamping

surfaces.

6 Do not use any loose reducing rings or bushes for

the reducing of holes on saw blades.

7 Make sure that xed reducer rings for securing the

insertion tool have the same diameter and have at

least 1/3 of the cutting diameter.

8 Make sure that xed reducer rings are parallel to

each other.

9 Handle insertion tool with caution. They are ideally

stored in the originally package or special contain-

ers. Wear protective gloves in order to improve

grip and to further reduce the risk of injury.

10 Prior to the use of insertion tools, make sure that

all protective devices are properly fastened.

11 Prior to use, make sure that the insertion tool

meets the technical requirements of this electric

tool and is properly fastened.

12 Only use the supplied saw blade for sawing opera-

tions in wood, materials similar to wood, plastics

and non-ferrous metals (except for magnesium and

alloys containing magnesium).

Attention: Laser radiation

Do not stare into the beam

Class 2 laser

Protect yourself and you environment from acci-

dents using suitable precautionary measures!

• Do not look directly into the laser beam with unpro-

tected eyes.

• Never look into the path of the beam.

• Never point the laser beam towards reecting sur-

faces and persons or animals. Even a laser beam

with a low output can cause damage to the eyes.

• Caution - methods other than those specied here

can result in dangerous radiation exposure.

• Never open the laser module. Unexpected exposure

to the beam can occur.

• If the saw is not used for an extended period of time,

the batteries should be removed.

• The laser may not be replaced with a different type

of laser.

• Repairs of the laser may only be carried out by the

laser manufacturer or an authorised representative.

Safety instructions for handling batteries

1 Always make sure that the batteries are inserted

with the correct polarity (+ and –), as indicated on

the battery.

2 Do not short-circuit batteries.

3 Do not charge non-rechargeable batteries.

4 Do not overcharge batteries!

5 Do not mix old and new batteries or batteries of

different types or manufacturers! Replace an entire

set of batteries at the same time.

6 Immediately remove used batteries from the device

and dispose of them properly!

7 Do not allow batteries to heat up!

8 Do not weld or solder directly on batteries!

9 Do not dismantle batteries!

10 Do not allow batteries to deform!

11 Do not throw batteries into re!

12 Keep batteries out of the reach of children.

13 Do not allow children to replace batteries without

supervision!

14 Do not keep batteries near re, ovens or other

sources of heat. Do not use batteries in direct sun-

light or store them in vehicles in hot weather.

15 Keep unused batteries in the original packaging and

keep them away from metal objects. Do not mix

unpacked batteries or toss them together! This can

lead to a short-circuit of the battery and thus dam-

age, burns or even the risk of re.

16 Remove batteries from the equipment when it will

not be used for an extended period of time, unless

it is for emergencies!

17 NEVER handle batteries that have leaked without

appropriate protection. If the leaked uid comes into

contact with your skin, the skin in this area should be

rinsed off under running water immediately. Always

prevent the uid from coming into contact with the

eyes and mouth. In the event of contact, please seek

immediate medical attention.

18 Clean the battery contacts and corresponding con-

tacts in the device prior to inserting the batteries:

Residual risks

The machine has been built according to the state of

the art and the recognised technical safety require-

ments. However, individual residual risks can arise

during operation.

• Health hazard due to electrical power, with the use of

improper electrical connection cables.

• Furthermore, despite all precautions having been met,

some non-obvious residual risks may still remain.

• Residual risks can be minimised if the „safety instruc-

tions“ and the „Proper use“ are observed along with

the whole of the operating instructions.

• Do not load the machine unnecessarily: excessive

pressure when sawing will quickly damage the saw

blade, which results in reduced output of the machine

in the processing and in cut precision.

• When cutting plastic material, please always use

clamps: the parts which should be cut must always

be xed between the clamps.

• Avoid accidental starting of the machine: the oper-

ating button may not be pressed when inserting the

plug in an outlet.

• Use the tool that is recommended in this manual. In

doing so, your saw provides optimal performance.

• Hands may never enter the processing zone when the

machine is in operation. Release the handle button

and switch off the machine prior to any operations.

• Prior to any adjustment, maintenance or service work

disconnect the mains power plug!

6. Technical data

AC motor 230 V~ 50Hz

performance 2000 Watt

operating mode S6 40%*

Idle speed 4800 min

-1

Hard-metal blade ø 254 x ø 30 x 2,8 mm

Number of teeth 24 / 48

Thickness riving knife 2,5 mm

minimum size work piece wxlxh 10x50x1 mm

table size 630 x 445 mm

Table width extension left/rights 620 x 250 mm

Table length extension rear 435 x 320 mm

Cutting height max. 90° 73 mm

Cutting height max. 45° 63 mm

height adjustment 0 - 73 mm

saw blade swivel 0 - 45°

suction port ø 34 mm

weight 28,5 kg

Laser class 2

Wavelength of laser 650 nm

Laser output < 1 mW

Laser module power supply

2 x 1,5 V

Micro (AAA)

* operating mode S6 40%: Continuous operation with in-

termittent loading (playing time 10 min).

Engine protection of to hot warming up:

It´s allowed to run the engine with nominal power maximum

40% of playing time. After this the machine must run 60% of

playing time steadily without load.

Noise values

The total noise values determined in accordance with

EN 61029.

sound pressure level L

96,2 dB(A)

uncertainty K

3 dB

sound power level L

109,2 dB(A)

uncertainty K

3 dB

Wear hearing protection.

The effects of noise can cause a loss of hearing. Total

vibration values (vector sum - three directions) deter-

mined in accordance with EN 61029.

7. Before starting the equipment

• The equipment must be set up where it can stand

securely, i.e. it should be bolted to a workbench, a

universal base frame or similar.

• All covers and safety devices have to be properly t-

ted before the equipment is switched on.

• It must be possible for the blade to run freely.

• When working with wood that has been processed

before, watch out for foreign bodies such as nails or

screws, etc.

• Before you press the ON/OFF switch check that the

saw blade is tted correctly. Moving parts must run

smoothly.

• Before you connect the equipment to the power sup-

ply make sure the data on the rating plate are dentical

to the mains data.

• Connect the machine to a properly installed protec-

tive contact socket, with at least 16A circuit breaker.

8. Attachment

Important. Pull out the power plug before carrying

out any maintenance, resetting or assembly work on

the circular saw!

Place all parts supplied on a at surface. Grouping

equal parts.

Note: If compounds with a bolt (round head / or hexa-

gon), hex nuts and washers are backed up, the washer

must be tted under the nut.

Insert screws each from outside to inside. Secure con-

nections with nuts on the inside.

Note: Tighten the nuts and bolts during assembly only

to the extent that they can not fall down.

If you tighten the nuts and bolts prior to nal assembly,

nal assembly can not be performed.

8.1 Assembling the base frame (Fig. 4-9)

1. Turn the saw upside down and place it on the oor.

2. Use hex screws (c), locking ring (g) and washers (a)

to fasten the four legs (18) loosely to the saw (Fig.

5). For this please use the Open-ended wrench (t).

m Attention !

2 legs have holes on the Rear, where the stand bars

are xed. (Fig. 9)

Make sure that they are attached to the back of the

machine.

3. Now loosely screw the longitudinal struts (20), the

cross struts (19) as well as the four center struts

(21, 22) to the legs using the round head screw (n),

washer (a), locking ring (g) and nuts (b) (Fig. 6-7)

4. Be sure to secure the round head screw (n) and nuts

(b) only loosely.

Important: The longer struts (marked with B)

have to be used on the sides.

- Secure center struts with hex bolts into each

other. (shown Fig. 7)

5. Now mount the four rubber feet (23) on the legs (Fig.

8).

6. Screw the stability bars (24) to the bore holes on the

rear legs using 2 hex screws (c), washers (a), lock-

ing ring (g) and nuts (b) on each side. (Fig. 9)

Important.

Both stability bars must be fastened at the

mounting points 38 and 39 at the rear of the

machine.

7. Finally, tighten all screws and nuts on the base

frame.

8.2 Fitting the table width extension and length

extension (Fig. 10-13,15)

1 Loosely fasten the table width extension (14) and

length extension (15) to the saw table (1) using the

hex bolt (c), locking ring (g) and the washers (u)

(Fig. 10-13,15).

2 Loosely screw the table supports (25, 26) to the hous-

ing of the bench-type circular saw with the hex screws

(c), locking ring (g) and washers (a). In addition the

table supports (25, 26) must be loosely screwed to

the width or length extension table with hex screws

(c), washers (a), locking ring (g) and nuts (b). (Use

the short supports (25) for the width extension and

the long supports (26) for the length extension) (Fig.

10-13,15).

3 Turn the saw together with the base frame and place

on the oor.

4 Align the table width extension and length extension

level with the saw table (1).

5 Finally, tighten all screws.

8.3 Mounting suction port (Fig. 14)

1. Fix the suction port (16) into the opening at the rear

of the machine.

m Caution!

The lateral entry should be facing outwards.

2. To secure the suction port - place the screws (d) in

the provided holes and tighten all.

8.4 Mounting the splitter, Fig.20-21

Important. Pull out the power plug.

The setting of the saw blade (5) has to be checked

each time after changing the saw blade.

1. Set the blade (5) to max. cutting depth, move to 0°

position and lock in place (see 9.2).

2. Take out the table insert (6) (see 8.6).

3. Slacken the xing screw (30) and insert the splitter.

4. The distance between the blade (5) and the splitter

(4) should be max. 5 mm. (Fig. 21).

5. Retighten the xing screw (30) and mount the table

insert (6) (see 8.6).

8.5 Fitting / removing the saw blade guard (Fig.

16-17)

1 The batteries for the laser must be inserted prior to

initial assembly (see 9.8).

2 Place the saw blade guard (2) together with the screw

(27) on top of the splitter (4) so that the screw is snug

in the oval hole (28).

3 Do not tighten the screw (27) too far – the blade

guard must be able to move freely.

4 Fit the extractor hose (3) to the extractor adapter

(16) and the extractor socket on the saw blade guard

(2). Connect a suitable chip extraction system to the

extractor adapter (16).

5 To dismantle, proceed in reverse order.

Important.

The saw blade guard (2) must always be lowered

over the workpiece before you begin to cut.

8.6 Changing the table insert (Fig. 18-19)

1 To prevent increased likelihood of injury, the table

insert (6) should be changed whenever it is worn

or damaged.

2 Remove the 2 countersunk head screws (29).

3 Take out the worn table insert (6).

4 Fit the replacement table insert by following the

above in reverse.

8.7 Adjusting / Mounting the splitter, Fig.20-21

m Important. Pull out the power plug.

The setting of the saw blade (5) has to be checked

each time after changing the saw blade.

1. Set the blade (5) to max. cutting depth, move to 0°

position and lock in place (see 9.2).

2. Dismantle the saw blade guard (2) (see 8.5).

3. Take out the table insert (6) (see 8.6).

4. Slacken the xing screw (30).

5. Push up the splitter (4).

6. The distance between the blade (5) and the splitter

(4) should be max. 5 mm. (Fig. 21).

7. Retighten the xing screw (30) and mount the table

insert (6) (see 8.6).

8. Remount the blade guard (2) (see 8.5).

8.8 Fitting/changing the blade (Fig. 22)

1. Important. Pull out the power plug and wear

protective gloves.

2. Dismantle the saw blade guard (2) (see 8.5).

3. Remove the table insert (6) by undoing the two

countersunk head screws (see 8.6).

4. Undo the nut with a wrench (s) (size 24) on the nut

itself and a second fork wrench (r) (size 22) on the

motor shaft to apply counterpressure (see Fig. 22).

5. Important! Turn the nut in the direction of rotation of

the saw blade.

6. Take off the outer ange and pull the old saw blade

off the inner ange by dropping the blade at an

angle.

7. Clean the saw blade ange thoroughly with a wire

brush before tting the new saw blade.

8. Mount and fasten the new saw blade in reverse

order.

Important. Note the running direction.

The cutting angle of the teeth must point in run-

ning direction, i.e. forwards (see the arrow on

the blade guard (2) )

9. Ret and set the table insert (6) and the saw blade

guard (2) (see 8.5 and 8.6)

10. Check to make sure that all safety devices are prop-

erly mounted and in good working condition before

you begin working with the saw again.

9. Using the saw

9.1 On/Off switch (Fig. 23)

- The saw can be switched on by pressing the green

pushbutton „I“.

- The red pushbutton „0“ has to be pressed to switch

off the saw.

9.2 Cutting depth (Fig. 23)

Turn the round handle (8) to set the blade (5) to the

required cutting depth.

- Turn anti-clockwise: larger cutting depth

- Turn clockwise: smaller cutting depth

After each new adjustment it is advisable to carry out a

trial cut in order to check the set dimensions.

9.3 Setting the angle (Fig. 23)

With the table saw you can make diagonal cuts to the

left oriented to the stop bar from 0 ° to 45 °.

m Check before each cut, that between the stop bar

(e), cross-stop (13) and the saw blade (5) a collision is

not possible.

- Undo the xing handle (9).

- Turn the handle (9.1) to set the desired angle on the

scale.

- Lock the xing handle (9) again in the required angle

position.

9.4 Parallel stop

9.4.1 Stop height (Fig. 24-25)

- The stop rail (e) for the parallel stop (7) has two dif-

ferent guide faces (high and low).

- For thick material you must use the stop rail (e) as

shown in Fig. 26, for thin material (with a workpiece

thickness of less than 25 mm) you must use the stop

rail as shown in Fig. 26.1.

9.4.2 Turning the stop rail (Fig. 24-25)

- First undo the wing nuts (f) to turn the stop rail (e).

- The stop rail (e) can now by pulled off the guide rail

(h) and can be pushed back over it with the appropri-

ate guide.

- Retighten the wing nuts (f).

9.4.3 Cutting width (Fig. 27-28)

- The parallel stop (7) has to be used when making

longitudinal cuts in wooden workpieces.

- The parallel stop should be mounted on the right-hand

side of the saw blade (5).

- Place the parallel stop on the guide rail for the parallel

stop (12) from above (Fig. 28).

- There are 2 scales (j/k) on the guide rail for the paral-

lel stop (12) which show the distance between the

stop rail (e) and the saw blade (5) (Fig. 27).

- Depending on this, choose the appropriate scale to

suit whether the stop rail (e) is turned for thick or thin

material:

High stop rail (thick material):

Scale j

Low stop rail (thin material):

Scale k

- Set the parallel stop (7) for the required dimension

using the inspection window (I) and secure it using the

eccentric lever for the parallel stop (31).

9.4.4 Adjusting the stop length (Fig. 29)

- The stop rail (e) can be moved in longitudinal direc-

tion in order to prevent the workpiece from becoming

jammed.

- Rule of thumb: The rear end of the stop comes up

against an imaginary line that begins roughly at the

center of the blade and runs at an angle of 45° to the

rear.

- Set the required cutting width.

- Slacken the wing nuts (f) and push the stop rail (e)

forward until it touches the imaginary 45° line.

- Tighten the wing nuts (f) again.

9.5 Adjusting the parallel stop (Fig. 30)

m Remove protective cap

- Set the saw blade (5) to maximum cutting depth (see

9.2).

- Set the parallel stop (7) so that the stop rail (e)

touches the saw blade (setting for thick material, also

see Point 9.4).

- If the parallel stop (7) is not in line with the saw blade

(5), undo the screws (m) on the parallel stop until the

parallel stop (7) can be adjusted in line with the saw

blade (5) (Figure 30).

- Re-tighten the screws (m).

9.6 Cross stop (Fig. 31)

• Slide the cross stop (13) into the groove (32) of the

table.

• Slacken the knurled screw (33).

• Turn the cross stop (13) until the required angle is set.

The notch (w) indicates the set angle.

• Retighten the knurled screw (33).

• When cutting you must use the stop rail (e) from the

parallel stop (7) to extend the length of the cross stop

(13) (Fig. 31-32)

• To extend the cross stop (13) with the stop rail (e), the

stop rail (e) must be removed of the parallel stop (7).

Now mount the stop rail as shown in Fig. 32, using the

wing nuts.

Important.

- Do not push the stop rail (e) too far toward the blade.

- The distance between the stop rail (e) and the blade

(5) should be approx. 2 cm (Fig. 31)

9.7 Adjusting the scale on the cross stop (Fig.

32)

- Place a 90° stop angle against the saw blade (5).

- Connect the cross stop (13) to the stop rail (e) of the

parallel stop (7) (see 9.6).

- Undo the knurled screw (33) of the cross top (13).

- Position the cross stop (13) so that the stop rail is in

a 90° angle to the saw blade (5). Now precisely align

the cross stop to the saw blade using the 90° stop

angle and retighten the knurled screw (33).

- Check if the cross stop is aligned at exactly 90°. If

this is not the case, continue as follows:

- Undo the two screws (o) holding the scale (p) to

the cross stop (13) until the scale can be set to

the correct position.

- Retighten the screws (o).

9.8 Using the laser (Fig. 34-35)

- The laser (34) enables you to make precision cuts

with your circular saw.

- The laser light is generated by a laser diode powered

by two batteries. The laser light is enlarged to form a

line and is emitted through the laser emission aper-

ture. You can then use the line as an optical marker

for the sawing line for precision cuts. Follow the laser

safety instructions.

- Inserting the batteries:

- Remove the saw blade guard (2) (see 8.4). The

laser is mounted on the splitter (4) and now easily

accessible.

- Set the Laser ON/OFF switch (35) to position 0

(laser off).

- Remove the battery compartment cover (37) by

undoing the screw (36). Now ip up the battery

compartment cover (37).

- Insert the batteries, ensuring that you t them the

right way round (see Fig. 35).

- Replace the battery compartment cover (37) and

secure it with the screw (36).

- Mount the safety hood (2) for the blade again.

- Switching the laser on: Set the Laser ON/OFF switch

(35) to I. When the saw blade guard (2) is mounted

you can easily access the Laser ON/Off switch (35)

through an opening provided in the saw blade guard

(Fig. 37). A red laser beam will now be projected from

the laser emission aperture. If you guide the laser

beam along the sawing line mark as you saw, you will

produce clean, precise cuts.

- Switching the laser off: Set the Laser ON/OFF switch

(35) to 0. The laser beam will go out. Always switch

off the laser when not in use in order to save the bat-

teries.

- The laser beam can be blocked by deposits of dust

and chips. You should therefore remove these parti-

cles from the laser emission aperture each time after

you use the laser (equipment off).

- Notes on batteries: If you do not intend to use the

laser for a lengthy period of time, remove the batteries

from the battery compartment. Any leakage of battery

uid might damage the tool.

- Do not place the batteries on heaters or expose them

to direct sunshine for long periods; temperatures in

excess of 50°C may damage the tool.

9.9 Adjusting the laser (Fig. 36)

If the laser (34) ceases to indicate the correct cutting

line, you can readjust the laser. To do so, open the

screws (z) and set the laser by using the adjustment bolt

(y) that the laser beam strikes the teeth of the saw blade

(5).

10. Operation

Working instructions

After each new adjustment it is advisable to carry out a

trial cut in order to check the set dimensions. After switch-

ing on the saw, wait for the blade to reach its maximum

speed of rotation before commencing with the cut.

Secure long workpieces against falling off at the end of

the cut (e.g. with a roller stand etc.)

Take extra care when starting the cut!

Never use the equipment without the suction function.

Regularly check and clean the suction channels.

Suitability of the saw blades:

- 24 teeth: soft materials, large chip depth, coarse cut

prole

- 48 teeth: hard materials, small chip depth, ne cut

prole

10.1 Making longitudinal cuts (Figure 38)

Longitudinal cutting (also known as slitting) is when you

use the saw to cut along the grain of the wood.

Press one edge of the workpiece against the parallel stop

(7) while the at side lies on the saw table (1). The blade

guard (2) must always be lowered over the workpiece.

When you make a longitudinal cut, never adopt a work-

ing position that is in line with the cutting direction.

- Set the parallel stop (7) in accordance with the work-

piece height and the desired width. (See 9.4)

- Switch on the saw.

- Place your hands (with ngers closed) at on the

workpiece and push the workpiece along the parallel

stop (7) and into the blade (5).

- Guide at the side with your left or right hand (depend-

ing on the position of the parallel stop) only as far as

the front edge of the saw blade guard (2).

- Always push the workpiece through to the end of the

splitter (4).

- The offcut piece remains on the saw table (1) until the

blade (5) is back in its position of rest.

- Secure long workpieces against falling off at the end

of the cut (e.g. with a roller stand etc.) (e.g. roller table

etc.)

10.1.1 Cutting narrow workpieces (Fig. 39)

Be sure to use a push stick (17) when making longitudi-

nal cuts in workpieces smaller than 120 mm in width. A

push block is supplied with the saw! Replace a worn or

damaged push stick immediately.

• Adjust the parallel stop to the width of workpiece you

require. (see 9.4)

• Feed in the workpiece with two hands. Always use the

push stick (17) in the area of the saw blade.

• Always push the workpiece through to the end of the

splitter.

m Caution! With short workpieces, use the push stick

from the beginning.

10.1.2 Cutting extremely narrow workpieces (Fig.

40)

Be sure to use a push block when making longitudinal

cuts in very narrow workpieces with a width of 30 mm

and less. The low guide face of the longitudinal stop is

best used in this case. Replace the push block without

delay when it becomes worn. There is no push block

supplied with the saw! (Available from your specialist

dealer) Replace the push block without delay when it

becomes worn.

• Adjust the parallel stop to the width of workpiece you

require.

• Use the push block to press the workpiece against

the stop rail and push the workpiece with the push

stick (17) through to the end of the splitter. There is no

push block supplied with the saw!

10.1.3 Making angular cuts (Fig. 41)

Angular cuts must always be made using the parallel

stop (7).

- Set the blade (5) to the desired angle. (See 9.3)

- Set the parallel stop (7) in accordance with the work-

piece width and height (see 9.4)

- Carry out the cut in accordance with the workpiece

width (see 10.1).

10.2 Making cross cuts (Fig. 31,42)

- Slide the cross stop (13) into one of the grooves

(32a/32b) in the table and adjust to the required an-

gle. (see 9.6). If you also want to tilt the blade (5), use

the groove (32a) which prevents your hand and the

cross stop from making contact with the blade guard.

- Use the stop rail (e).

- Press the workpiece rmly against the cross stop (13).

- Switch on the saw.

- Push the cross stop (13) and the workpiece toward

the blade in order to make the cut.

- Important:

Always hold the guided part of the workpiece.

Never hold the part which is to be cut off.

- Push the cross stop (13) forward until the workpiece is

cut all the way through.

- Switch off the saw again. Do not remove the offcut

until the blade has stopped rotating.

10.3 Cutting particle boards

To prevent the cutting edges from cracking when work-

ing with particle boards, you should not set the saw

blade (5) more than 5mm greater than the thickness of

the workpiece (also see 9.2).

11. Transport

1. Turn off the power tool before any transport and

disconnect it from the power supply.

2. Apply the power tool at least with two people, do

not touch the table extensions.

Use only the transport handles (Figure 43/44)

punched into both sides of the housing for trans-

porting the equipment.

3. Protect the power tool from knocks, bumps and

strong vibrations, such as during transport in vehi-

cles.

4. Secure the power tool against overturning and slid-

ing.

5. Never use the safety devices for handling or trans-

porting purposes.

12. Maintenance

m Warning! Prior to any adjustment, maintenance or

service work disconnect the mains power plug!

12.1 General maintenance measures

• Keep all safety devices, air vents and the motor hous-

ing free of dirt and dust as far as possible. Wipe the

equipment with a clean cloth or blow it down with com-

pressed air at low pressure.

• We recommend that you clean the equipment imme-

diately after you use it.

• Clean the equipment regularly with a damp cloth and

some soft soap. Do not use cleaning agents or sol-

vents; these may be aggressive to the plastic parts in

the equipment. Ensure that no water can get into the

interior of the equipment.

• In order to extend the service life of the tool, oil the

rotary parts once monthly. Do not oil the motor.

12.2 Brush inspection

In case of excessive sparking, have the carbon brushes

checked only by a qualied electrician. Important. The

carbon brushes should not be replaced by anyone but a

qualied electrician.

13. Storage

Store the device and its accessories in a dark, dry and

frost-proof place that is inaccessible to children. The

optimum storage temperature is between 5 and 30˚C.

Store the electrical tool in its original packaging.

Cover the electrical tool in order to protect it from dust

and moisture.

Store the operating manual with the electrical tool.

14. Electrical connection

The electrical motor installed is connected and

ready for operation. The connection complies with

the applicable VDE and DIN provisions.

The customer‘s mains connection as well as the

extension cable used must also comply with these

regulations.

• The product meets the requirements of

EN 61000-3-11 and is subject to special connec-

tion conditions. This means that use of the product

at any freely selectable connection point is not al-

lowed.

• Given unfavorable conditions in the power supply the

product can cause the voltage to uctuate temporarily.

• The product is exclusively intended for use at con-

nection points that have a continuous current-carry-

ing capacity of at least 100 Amper phase.

• As the user, you are required to ensure, in consulta-

tion with your electric power company if necessary,

that the connection point at which you wish to ope-

rate the product meets the specied requirements.

Important information

In the event of an overloading the motor will switch

itself off. After a cool-down period (time varies) the mo-

tor can be switched back on again.

Damaged electrical connection cable

The insulation on electrical connection cables is often

damaged.

This may have the following causes:

• Passage points, where connection cables are

passed through windows or doors.

• Kinks where the connection cable has been improp-

erly fastened or routed.

• Places where the connection cables have been cut

due to being driven over.

• Insulation damage due to being ripped out of the

wall outlet.

• Cracks due to the insulation ageing.

Such damaged electrical connection cables must not

be used and are life-threatening due to the insulation

damage.

Check the electrical connection cables for damage regu-

larly. Make sure that the connection cable does not hang

on the power network during the inspection.

Electrical connection cables must comply with the ap-

plicable VDE and DIN provisions. Only use connection

cables with the marking „H05VV-F“.

The printing of the type designation on the connection

cable is mandatory.

AC motor

• The mains voltage must be 230 V~

• Extension cables up to 25 m long must have a

cross-section of 1.5 mm

Connections and repairs of electrical equipment may

only be carried out by an electrician.

Please provide the following information in the event of

any enquiries:

Type of current for the motor

• Machine data - type plate

15. Disposal and recycling

The equipment is supplied in packaging to pre-

vent it from being damaged in transit. The raw

materials in this packaging can be reused or recy-

cled. Never place batteries in your household refuse, in

re or in water. Batteries should be collected, recycled or

disposed of by environment-friendly means. The equip-

ment and its accessories are made of various types of

material, such as metal and plastic. Defective compo-

nents must be disposed of as special waste. Ask your

dealer or your local council.

16. Troubleshooting

Problem Possible Cause Help

Saw blade gets loose

after turning off the

motor

Fastening nut tightened insufciently Tighten fastening nut, M20 left-handed thread

Motor does not start a) Fastening nut tightened insufciently

b) Extension cable defect

c) Connections on the motor or switch defect

a) Check the mains fuse.

b) See “Electrical Connection” in the operating

manual

c) Have it checked by an electrician

No motor output turns

off automatically

Overload by dull saw blade, thermoprotection

is triggered

Insert a sharpened saw blade; motor can be turned

on again after the cooling period

Burns on the cutting

surface

c) with longitudinal cuts

d) with cross cuts

a) Fastening nut tightened insufciently

b) Wrong saw blade

c) Longitudinal stop not parallel

d) Slide carriage not parallel

a) Insert a sharpened saw blade

b) Insert saw blade with 20 or 28 teeth for

longitudinal cuts

c) Exchange the longitudinal stop

Align the slide carriage with the saw blade

17. Warranty certicate

All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your

device develops a fault, please contact our service department at the address shown on this guarantee card. Of course, if you

would prefer to call us then we are also happy to offer our assistance under the service number printed below. Please note the

following terms under which guarantee claims can be made:

• These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights. We do not charge

you for this guarantee.

• Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the rectication of

these defects or replacement of the device. Please note that our devices have not been designed for use in commercial, trade

or industrial applications. Consequently, the guarantee is invalidated if the equipment is used in commercial, trade or industrial

applications or for other equivalent activities. The following are also excluded from our guarantee: compensation for transport

damage, damage caused by failure to comply with the installation/assembly instructions or damage caused by unprofessional

installation, failure to comply with the operating instructions (e.g. connection to the wrong mains voltage or current type), mis-

use or inappropriate use (such as overloading of the device or use of non-approved tools or accessories), failure to comply with

the maintenance and safety regulations, ingress of foreign bodies into the device (e.g. sand, stones or dust), effects of force or

external inuences (e.g. damage caused by the device being dropped) and normal wear resulting from proper operation of the

device.

The guarantee is rendered null and void if any attempt is made to tamper with the device.

• The guarantee is valid for a period of 3 years starting from the purchase date of the device. Guarantee claims should be

submitted before the end of the guarantee period within two weeks of the defect being noticed. No guarantee claims will be

accepted after the end of the guarantee period. The original guarantee period remains applicable to the device even if repairs

are carried out or parts are replaced. In such cases, the work performed or parts tted will not result in an extension of the

guarantee period, and no new guarantee will become active for the work performed or parts tted. This also applies when an

on-site service is used.

• In order to assert your guarantee claim, please send your defective device postage-free to the address shown below. Please

enclose either the original or a copy of your sales receipt or another dated proof of purchase. Please keep your sales receipt in

a safe place, as it is your proof of purchase. It would help us if you could describe the nature of the problem in as much detail

as possible. If the defect is covered by our guarantee then your device will either be repaired immediately and returned to you,

or we will send you a new device.

Of course, we are also happy offer a chargeable repair service for any defects which are not covered by the scope of this guar-

antee or for units which are no longer covered. To take advantage of this service, please send the device to our service address.

Stránka sa načítava ...

Parkside PTK 2000 A1 Návod na používanie

Značka: Parkside

Model: PTK 2000 A1

Typ: Návod na používanie

Stiahnite si PDF

správa

V iných jazykoch

Deutsch: Parkside PTK 2000 A1 Bedienungsanleitung

Parkside PTK 2000 A1 Návod na používanie

Parkside PTK 2000 A1 Návod na používanie

V iných jazykoch

Súvisiace články

Ďalšie dokumenty