Parkside PTK 2000 B2 Translation Of The Original Instructions

Typ
Translation Of The Original Instructions
TABLE SAW PTK 2000 B2
IAN 273460
STOLOVÁ KOTOUČOVÁ
Překlad originálního provozního návodu
TISCHKREISSÄGE
Originalbetriebsanleitung
STOLOVÁ KOTÚČOVÁ PÍLA
Preklad originálneho návodu na obsluhu
TABLE SAW
Translation of the original instructions
FŰRÉSZASZTAL
Az originál használati utasítás fordítása
273460_par_Tischkreissaege_cover_HU_CZ_SK.indd 2 29.01.16 12:47
GB Translation of the original instructions Page
HU Az originál használati utasítás fordítása Oldal
CZ Překlad originálního provozního návodu Strana
SK Preklad originálneho návodu na obsluhu Strana
DE / AT / CH Originalbetriebsanleitung Seite
Before reading, unfold the page containing the illustrations and familiarise yourself with all
functions of the device.
Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik
funkcióját.
Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.
Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend
mit allen Funktionen des Gerätes vertraut.
273460_par_Tischkreissaege_cover_HU_CZ_SK.indd 3 29.01.16 12:47
6
32
58
83
108
1
2
4
3
1 2
2 3
4
5
17
24
2122
18
23
19
20
16
3 4 5 6
14
11
12
13
9
8
7
15
10
r
a b c d e
s
t
11 12
9
f g
3
9
11
7
5
10
12
8
6
18
18
26
25
f a c
18
24
23
19
20
21
22
38
38
38
f
f
r
r
r
r
r
7
7
7
d,a,b,c=e
d,a,b,c=e
d,a,b,c=e
7
15
15
f,a,c=g
4
m a x . 3 -8 m m
17
19
15
13
18
20
16
14
37
36
35
28
4
27
2
6
29
29
34
f,a,c=g
f
r
f
+
+
16
f,a,c=g
r
30
25
25
26
25
25
26
5
6
G B
Content
Introduction .................................... 6
Intended purpose ............................ 7
General description ......................... 7
Extent of the delivery ....................... 7
Overview ....................................... 8
Functional description ....................... 9
Technical data ................................. 9
Safety Instructions ............................ 9
Symbol and icons ............................ 9
Symbols on the appliance ................. 9
Assembly ...................................... 17
Mounting of the Frame .................... 17
Mounting the table width and length
extension ...................................... 18
Mounting the Suction Adapter ......... 18
Mounting the Riving Knife ............... 18
Mounting/dismounting the
Saw Blade Guard ......................... 19
Replacing the Table Insert ................ 19
Adjusting/mounting the Riving Knife . 19
Attaching/changing the Saw Blade .. 20
Before putting into operation ........... 20
Operation .................................... 20
Switching on and off ..................... 20
Adjusting the Cutting Depth ............. 21
Angle Adjustment ........................... 21
Working with the Parallel Stop ......... 21
Adjusting the Stop Height ............... 21
Turning the Stop Rail ....................... 21
Adjusting the Cutting Width ........... 21
Adjusting the Stop Length ................ 22
Adjusting the Parallel Stop .............. 22
Transverse stop .............................. 22
Adjusting the Scale of the
Transverse Stop ............................. 23
Using the Laser ............................. 23
Adjusting the Laser ........................ 23
Operation .................................... 23
Performing Longitudinal Cuts .......... 24
Cutting narrow Workpieces ............ 24
Cutting very narrow Workpieces ..... 24
Performing Bevel Cuts .................... 25
Performing Transverse Cuts ............. 25
Cutting Chipboard ........................ 25
Transport ...................................... 25
Cleaning and Servicing ................. 26
Cleaning ....................................... 26
Storage......................................... 26
Waste disposal and environment
protection ..................................... 26
Spare parts/accessories
................. 27
Guarantee ................................... 28
Trouble Shooting ............................ 30
Service-Center .............................. 31
Importer ....................................... 31
Translation of the original
EC declaration of conformity ......... 134
Introduction
Congratulations on the purchase of your
new device. With it, you have chosen a
high quality product.
During production, this equipment has
been checked for quality and subjected to
a nal inspection. The functionality of your
equipment is therefore guaranteed.
The operating instructions constitute part of
this product. They contain important infor-
mation on safety, use and disposal.
Before using the product, familiarise your-
self with all of the operating and safety
instructions. Use the product only as de-
scribed and for the applications specied.
Keep this manual safely and in the event
that the product is passed on, hand over
all documents to the third party.
7
G B
Intended purpose
The table circular saw is used for cutting all
types of wood lengthwise and crosswise
(only with the transverse stop), depending
on the machine size. All types of round
timbers must not be cut with it. The ma-
chine may be used only for its prescribed
purpose.
Any other use beyond that is considered to
be not in accordance with the designated
purpose. The user/operator is liable for all
types of resulting damage or injury and not
the manufacturer.
The only saw blades which may be used
are those which are suitable for the machi-
ne (HM or CV saw blades).
The use of any type of HSS saw blades
and cutting discs is prohibited. Use in ac-
cordance with the designated purpose is
also deemed to include observance of the
safety instructions, as well as the assembly
and operating instructions in the opera-
ting manual.Individuals who operate and
maintain the machine must be familiar with
it and must have been instructed in possi-
ble hazards. Moreover, the latest accident
prevention regulations must be strictly ob-
served. Other general rules in the elds of
occupational health and safety technology
must be complied with.
Caution!
When using equipment, certain safety
precautions must be complied with in order
to avoid injuries and damage. You should
therefore read these operating instructions
/ safety instructions carefully. Keep these
in a safe place so that the information is
available to you at all times. Should you
give the device to anyone else, please give
them these operating instructions / safety
instructions as well. We assume no liability
for accidents or damage caused by failure
to observe these instructions or the safety
instructions. Changes to the machine will
cause the manufacturer‘s liability with
respect to any resulting damage to be com-
pletely excluded. Even when the device is
used in accordance with the designated
purpose, it is nevertheless not possible to
completely eliminate certain residual risk
factors. Due to the design and structure of
the machine, the following risks may occur:
Touching the saw blade in the area of
the saw which is not covered;
Reaching into the running saw blade
(cuts)
Kickback of workpieces and workpiece
parts.
Saw blade breaks.
Ejection of faulty hard metal parts of
the saw blade.
Hearing damage if the necessary hea-
ring protection is not used.
Emissions of wood dust which are
harmful to the health when used in clo-
sed rooms.
Please note that the use of our devices in
accordance with the designated purpose
does not include commercial, handicraft or
industrial applications. We assume no war-
ranty if the device is used in commercial,
handicraft or industrial businesses or for
equivalent purposes..
General description
Extent of the delivery
Carefully unpack the appliance and check
that it is complete:
- - Saw table with pre-assembled, carbide-
tipped saw blade with 24 teeth
- Carbide-tipped saw blade with 48 teeth
- Blade guard
8
G B
- Suction hose
- Suction adapter with rubber seal
- Riving knife with laser
- Batteries 1.5V AAA (2x)
- Parallel stop
- Stop rail
- Transverse stop
- Table width extender (2x)
- Table length extender
- Push stick
- Legs (4x)
- Cross struts (2x)
- Longitudinal struts (2x)
- Central struts, short (2x)
- Central struts, long (2x)
- Rubber feet (4x)
- Stand brackets (2x)
- Table supports, short (4x)
- Table supports, long (2x)
- Translation of the original instructions for use
Mounting Material
- Bag A for legs and central struts: Hexago-
nal bolt with mounted washer/
spring washer (f), 8 pieces;
Hexagonal bolt (g) = lock
washer (b), 2x washer (a), nut
(c), 4 pieces;
Round head bolt, M6 x 12 (e) =
washer (a), lock washer (b), nut
(c), 8 pieces each
- Bag B for stand bracket and upper struts:
Round head bolt, M6 x 12 (d) =
washer (a), lock washer (b), nut
(c), 20 pieces each
- Bag C for table length/width extension:
Hexagonal bolt with mounted
washer/spring washer (f),
12 pieces;
Hexagonal bolt (g) = lock
washer (b), 2x washer (a), nut
(c), 6 pieces
Tools
- Jaw spanner SW 22
- Hexagon socket wrench HX 6
- Jaw spanner SW 8/10
The illustrations are on the
fold-out pages.
Overview
1
1 Saw table
2 Blade guard
3 Suction hose
4 Riving knife
5 Saw blade
6 Table insert
7 Table width extender
8 Transverse stop
9 Locking handle
10 Base
11 On/off switch
12 Handwheel
13 Guide rail
14 Parallel stop
15 Table length extender
16 Suction adapter with Rubber seal
17 Push stick
18 Legs
19 Cross struts
20 Longitudinal struts
21 Central struts, short
22 Central struts, long
23 Rubber feet (4x)
24 Stand brackets (2x)
25 Table brackets, short
26 Table brackets, long
27 Bolt with wing nut
28 Slot in the riving knife
29 Countersunk screws of the table
insert
30 Fixing bolts of the riving knife
31 Cam lever
32 Groove
33 Knurled screw
34 Laser
9
G B
35 Laser switch
36 Screws for battery compartment
37 Battery cover
38 Attachment points
39 Stop rail
Functional description
The table circular saw is used for cutting all
types of wood lengthwise and crosswise
(only with the transverse stop), depending
on the machine size. All types of round
timbers must not be cut with it.
Technical data
Bench circular saw.........................PTK 2000 B2
AC motor .......................... 230 V
~
50Hz
Power ................................... 2000 Watt
Operating mode .......................S6 40%*
Safety class .......................................... I
Protection category...........................IP20
Idling speed ...........................4800 min
-1
Carbide saw blade ø 254 x ø 30 x 2,8 mm
Number of teeth ......................... 24 / 48
Thickness riving knife ................... 2,5 mm
min. Workpiece size WxLxH 10x50x1 mm
Table size .........................630 x 445 mm
Table width extender
left/right ..........................620 x 250 mm
Table length extender rear ..435 x 320 mm
Cutting height max. 90° ................ 73 mm
Cutting height max. 45° ................ 63 mm
Height adjustment ................... 0 - 73 mm
Saw blade, swivelling ................... 0 - 45°
Extraction connection ................. ø 34 mm
Weight (including accessories),
......................................approx 29,5 kg
Laser class
........................................... 2
Laser wavelength ........................650 nm
Laser power .............................. < 1 mW
Laser module power supply
............................2 x 1,5 V Micro (AAA)
Sound pressure level
(L
pA
) .....................92 dB(A); K
pA
= 3 dB
Sound power level (L
WA
)
measured ............105 dB(A); K
WA
= 3 dB
guaranteed .........................108 dB(A)
* Operating mode S6 40%: Continuous operati-
on with intermittent load (cycle time 10 min). In
order not to heat the motor more than permitted,
the motor may only be operated for 40% of the
cycle time with the stated nominal power and
must then continue running for 60% of the cycle
time without a load.
Technical and optical changes may be
undertaken in the course of further devel-
opment without notice. All dimensions,
references and information in this instruc-
tion manual are therefore not guaranteed.
Legal claims made on the basis of the
instruction manual can therefore not be
considered as valid.
Safety instructions
Ensure that the safety instructions are ob-
served when operating the appliance.
Symbols and icons
Symbols on the appliance:
Carefully read these Operating In-
structions.
Wear eye protection.
Wear ear protection.
Wear breathing protection.
Caution - Risk of injury. Never re-
ach into the running blade.
1 0
G B
Do not expose the unit to rain. The
device must not be wet, nor should
it be operated in a moist environ-
ment.
Caution - a damaged blade must
not be used under any circum-
stances. Replace the saw blade im-
mediately.
Caution! - Laser radiation. Do not
look into the beam.
Laser class 2
108
Information of the acoustic power
level L
WA
in dB.
Electrical appliances must not be dis-
posed of with the domestic waste.
Symbols in the manual
Warning symbols with in-
formation on damage and
injury prevention.
Instruction symbols (the instruction is
explained at the place of the excla-
mation mark) with information on
preventing damage.
Help symbols with information on
improving tool handling.
Safe operation
1 Keep work area clear.
Cluttered areas and benches invite
injuries.
2 Consider work area
environment.
Do not expose tools to rain.
Do not use tools in damp or wet
locations.
Keep work area well lit.
Do not use tools in the presendce
of ammable liquids or gases.
3 Guard against electric shock
Avoid body contact with earthed
or grounded surfaces (e.g. pipes,
radiators, ranges, refrigerators).
4 Keep other persons away!
Do not let persons, especially child-
ren, not involved in the work touch
the tool or the extension cord and
keep them away from the work
area.
5 Store idle tools
When not in use, tools should be
stored in a dry locked-up place,
out of the reach of children.
6 Do not force the tool.
It will do the job better and safer at
the rate for which it was intended.
7 Use the right tool.
Do not force small tools to do the
job of a heavy tool.
Do not use the power tool for such
purposes for which it is not inten-
ded. Use for example no circular
saws to cut tree branches or logs.
Do not use the electric tool to the
rewood saws.
1 1
G B
8 Dress properly.
Do not wear loose clothing or
jewellery, they can be caught in
moving parts.
Non-skid footwear is recommen-
ded when working outdoors.
Wear protective hair covering to
contain long hair.
9 Use protective equipment.
Use safety glasses.
Use face or dust mask if working
operations create dust.
10 Connect dust extraction
equipment
If the tool is provided for the
connection of dust extraction and
collecting equipment, ensure these
are connected and properly used.
Indoor operation is permitted only
with a suitable extraction system.
11 Do not abuse the cord.
Never yank the cord do disconnect
it from the socket. Keep the cord
away from heat, oil and sham
edges.
12 Secure work.
For long workpieces, an additional
supporting surface (table, trestles,
etc.) is required in order to prevent
tipping of the machine.
Always press the workpiece rmly
against the working surface and
stop in order to prevent wobbling
or twisting of the workpiece.
13 Do not overreach
Keep proper footing and balance
at all times.
Avoid awkward hand positions
in which one or both hands could
touch the saw blade as the result
of a sudden slip.
14 Maintain tools with care
Keep cutting tools sharp and clean
for better and safer performance.
Follow instruction for lubricating
and changing accessories.
Inspect tool cords periodically and
if damaged have them repaired by
an authorized service facility.
Inspect extension cords periodi-
cally and replace if damaged.
Keep handles dry, clean and free
from oil and grease.
15 Disconnect tools.
Never remove loose splinters,
chips or jammed pieces of wood
when the saw blade is running.
When the electric tool is not in
use, before maintenance and when
changing tools such as the saw
blade, drill bit, milling cutter.
16 Remove adjusting keys and
wrenches
Form the habit of checking to see
that keys and adjusting wrenches
are removed from the tool before
turning it on.
17 Avoid unintentional starting.
Ensure switch is in “off position
when plugging in.
18 Use outdoor extension leads.
When the tool is used outdoors,
use only extension cords intended
for outdoor use and so marked.
Use the cable drum only in the
unrolled state.
19 Stay alert.
Watch what you are doing, use com-
mon sense and do not operate the tool
when you are tired.
20 Check damaged parts.
Before further use of tool, it should
1 2
G B
be carefully checked to determine
that it will operate properly and
perform its intended function.
Check whether the moving parts
are working properly and are not
becoming jammed or whether
parts are damaged. All parts must
be correctly tted and satisfy all
conditions to ensure the proper
operation of the power tool.
The movable guard must not be
clamped when it is open.
A guard or other part that is dama-
ged should be properly repaired or
replaced by an authorized service
centre unless otherwise indicated
in this instruction manual.
Have defective switches replaced
by an authorized service centre.
Do not use any faulty or damaged
connection cables.
Do not use the tool if the switch
does not turn it on and off.
21 Warning!
The use of any accessory or attach-
ment other than one recommended
in this instruction manual may
present a risk of personal injury.
22 Have your tool repaired by a
qualied person.
This electric tool complies with
the relevant safety rules. Repairs
should only be carried out by qua-
lied persons using original spare
parts, otherwise this may result in
considerable danger to the user.
ADDITIONAL SAFETY
INSTRUCTIONS
1 Safety Precautions
Warning! Do not use damaged,
cracked or deformed saw blades.
Replace a worn table insert.
Regrinding is not allowed.
Only use saw blades recommen-
ded by the manufacturer which
conform to EN 847-1. Warning!
When changing the saw blade
ensure that the cutting width is not
smaller and the main blade thick-
ness of the saw blade not greater
than the thickness of the riving
knife!
Make sure that a saw blade is
selected which is appropriate for
the material to be cut.
- Wear appropriate personal pro-
tective equipment. This includes:
Hearing protection to reduce the
risk of becoming hard of hearing,
breathing respirator to reduce the
risk of inhaling hazardous dust.
- Wear gloves when handling saw
blades and rough materials.
- Whenever practicable, saw blades
should be carried in a container.
Wear safety goggles. Any splin-
ters, chips and dusts which are
ejected from the device when it is
in operation may cause sight loss.
Connect the power tool to a dust
collection device when sawing
wood. Among other things, the
emission of dust is affected by the
type of material to be machined,
the importance of local deposition
(capture or source) and the correct
setting of hoods/deector plates/
guide mechanisms.
- Do not use any saw blades made
of high-alloy high-speed steel
(HSS).
Always store the push stick or
push block in its holder on the
power tool when not in use.
1 3
G B
2 Maintenance and Servicing
Always remove the mains plug
when carrying out any adjustments
or maintenance work.
The cause of the noise is inuenced
by various factors, including the
properties of the blades, the con-
dition of the saw blade and power
tool. If possible, use saw blades
that are designed to reduce the
noise level, service the power tool
and tool attachments regularly and
repair them if necessary to reduce
noise.
- Report any faults to the power tool,
safety devices or the tool attach-
ment as soon as they are disco-
vered to the person responsible for
safety.
3 Safe Working
Use the push stick or the handle
with push block to pass the workpi-
ece safely past the saw blade.
Make sure that the riving knife
is always used and that this is
correctly adjusted.
Use the upper blade guard and
adjust it correctly.
Use only saw blades whose maxi-
mum speed is not lower than the
maximum spindle speed of the tool
being used and which are suitable
for the material to be cut.
Do not create any rebates or
grooves unless a suitable protective
device, such as a tunnel guard, is
attached above the saw table.
Circular saws must not be used for
slotting (cutting grooves which end
in the workpiece).
When transporting the power
tool, use only the transport devices
supplied. Never use the guards for
handling or transporting the tool.
- During transport, make sure that
the top part of the saw blade is co-
vered, for example with the guard.
Ensure that the only spacer
washers and spindle rings which
are used are suitable for the purpo-
se stated by the manufacturer.
The oor around the machine must
be at, clean and free of loose
particles such as chips and cutting
residues.
Working position always to the
side of the saw blade.
Do not remove any cutting residues
or other parts of the workpiece
from the cutting area for as long
as the machine is running and the
sawing unit is not yet in the rest
position.
Secure long workpieces against
tilting at the end of the cutting
operation (e.g. unwinding stand or
roller stand).
Caution! long workpieces against
tilting at the end of the cutting
operation (e.g. unwinding stand or
roller stand).
Caution! Never remove any loose
splinters, chips or jammed pieces
of wood when the saw blade is
still running.
Always switch off the machine and
remove the plug before repairing
any faults or removing jammed
pieces of wood.
Always switch off the motor and
remove the plug before carrying
out any conversions or adjustment,
measurement and cleaning work.
Before switching on, check that
the spanners and adjustment tools
have been removed.
1 4
G B
Warning! During operation, this power
tool produces an electromagnetic eld.
Under certain circumstances, this eld may
negatively affect active or passive medical
implants. In order to reduce the danger of
serious or fatal injuries, we recommend
that individuals who wear medical im-
plants should consult their doctor and the
manufacturer of the implant before opera-
ting the power tool.
SAFETY INSTRUCTIONS FOR
HANDLING SAW BLADES
1 Only use tools which you know how to
handle.
2 Pay attention to the maximum speed.
The maximum speed stated on the tool
being used must not be exceeded.
Keep within the speed range if one is
specied.
3 Note the direction of rotation of the
motor and saw blade.
4 Circular saw blades with cracks in
them must be taken out of service
(repair is not permitted).
5 Tools with visible cracks must not be
used.
6 Tools must be cleaned regularly.
7 Handle the tools used with care. It is
best to store these in their original pa-
ckaging or special containers. Always
wear protective gloves to improve
your grip and further reduce the risk of
injury.
8 Before using any of the tools, ensure
that all protective devices are correctly
attached.
9 Before use, ensure that all of the tools
used by you full the technical requi-
rements of this power tool and are
properly attached.
10 The saw blade supplied should only
be used for sawing wood and never
for working metal.
Assembly and Attachment of Tools
and Tool Parts
a) Tools and tool bodies must be tighte-
ned in such a way that they cannot
become loose during operation.
b) Attachment bolts and nuts are to be
tightened to the torques specied by
the manufacturer using appropriate
spanners etc.
c) Extending a spanner or tightening
with the help of hammer blows is not
permitted.
d) The tightening surfaces must be clea-
ned to remove any dirt, grease, oil
and water.
e) Tensioning bolts must be tightened in
accordance with the manufacturer‘s
instructions.
f) In order to adjust the borehole diame-
ter of circular saw blades to the spind-
le diameter of the machine, only rmly
inserted rings, e.g. rings which have
been pressed into place or which are
held in place by means of an adhesive
bond, may be used. The use of loose
rings is not permitted.
g) Ensure that xed reducing rings are
positioned parallel to one another.
Safety Instructions for Handling the
Laser
Caution: Laser radiation - Do not look
into the beam - Laser class 2
1 5
G B
Safety Instructions for Handling
Batteries
1 Ensure at all times that the batteries
are inserted with the correct polarity (+
and –), as shown on the battery itself.
2 Do not short-circuit the batteries.
3 Do not charge up rechargeable batte-
ries.
4 Do not overcharge the battery!
5 Do not mix old and new batteries or
batteries of a different type or from
different manufacturers! Replace all
batteries of a set at the same time.
6 Remove used batteries immediately
out of the device and dispose of them
correctly!
7 Do not heat the batteries!
8 Do not carry out any welding or solde-
ring work directly to the batteries!
9 Do not take the batteries apart!
10 Do not deform the batteries!
11 Do not throw the batteries into the re!
12 Store the batteries out of the reach of
children.
13 Do not allow children to replace the
batteries without supervision!
14 Do not store the batteries close to a
re, cookers or other sources of heat.
Do not place the battery in direct
sunlight and do not use or store it in
motor vehicles in hot weather.
15 Store used batteries in the original
packaging and keep them away
from metal objects. Do not mix (up)
unpacked batteries! Otherwise this
may cause the battery to short-circuit,
resulting in damage, burns or even the
danger of re.
16 Remove batteries from the device if this
is not going to be used for a prolon-
ged period, unless it is to be used in
emergencies!
17 NEVER touch batteries which have
leaked without appropriate protection.
If the leaked liquid comes into contact
with the skin, you should rinse off this
area of the skin immediately under
running water. Make sure at all events
that your eyes and mouth do not come
into contact with the liquid. If they do,
seek medical advice immediately.
18 Clean the battery contacts and the
equivalent contacts in the device befo-
re inserting the batteries.
Residual Risks
This power tool has been construc-
ted in accordance with the latest
technology and the generally re-
cognised safety regulations. Never-
theless, it is possible that individual
residual risks may occur during
operation.
Electrical hazard if improper electrical
connection cables are used.
In addition, concealed residual risks
may be present in spite of all the
precautions that have been taken.
Residual risks can be minimised by
observing the „Safety instructions“ and
„Use in accordance with the designa-
ted purpose“, as well as the operating
instructions.
Do not put any unnecessary stresses
on the machine: excessive pressure
during sawing will quickly damage
the saw blade. This may result in a
1 6
G B
reduction in the performance of the
machine, as well as a reduction in the
cutting accuracy.
Avoid switching the machine on by
accident: when inserting the plug into
the socket, the power button must not
be pressed.
Use the tool which is recommended
in this manual. This will ensure the
optimal performance of your saw.
Keep your hands away from the
working area when the machine is in
operation.
Before you carry out any adjustments
or servicing work, turn the device off
and remove the mains plug.
5. Electrical Connection
The installed electric motor is
connected ready for operation.
The connection complies with the
relevant VDE and DIN regulations.
The customer‘s network connection
and any extension cable used must
comply with these regulations.
The product meets the requirements
of EN 61000-3-11 and is subject to
special connection conditions. This
means that its use at freely selectable
connection points is not permitted.
If the network conditions are unfa-
vourable, the device may result in
temporary voltage uctuations.
The maximum permitted mains
impedance at the electrical connec-
tion point of 0.107 ohm must not be
exceeded.
As the user, you must ensure – in
consultation with your electricity sup-
ply company if necessary – that the
continuous current carrying capacity
of the network at the connection point
to the public mains is sufcient for the
connection of the product.
Important Instructions
If the motor is overloaded, it switches
itself off automatically. After cooling down
(times vary), the motor can be switched on
again.
Faulty Electrical
Connection Cable
Insulation damage often occurs to electrical
connection cables.
The causes of this may be as follows:
Pressure points if connection cables
are routed through windows or door
gaps.
Kinks caused by improper attachment
or routing of the connection cable.
Cut surfaces caused by vehicles dri-
ving over the connection cable.
Insulation damage caused by tearing
out of the wall socket.
Cracks resulting from the insulation
becoming old.
Such faulty electrical connections must not
be used and may endanger life due to the
damage to the insulation.
Electrical connection cables should be
checked regularly for damage. Ensure that
during such checks, the connection cable is
not connected to the mains.
Electrical connection cables must comply
with the relevant VDE and DIN regulati-
ons. Only use connection cables with the
marking H05VV-F.
It is stipulated by law that the type of con-
nection cable must be printed on it.
1 7
G B
Alternating Current Motor
The mains voltage must be 230 V~.
Extension cables up to 25 m in length
must have a cross-section of 2.5 mm².
Connections and repairs to the electrical
equipment may only be performed by
a qualied electrician. If you have any
queries, please provide the following
information:
Current type of the engine
Data from the machine type plate
Data from the motor type plate
Assembly
Assembly, Replacement of Parts
and Adjustments
Caution! The mains plug must be
removed before all servicing, ret-
ooling and assembly work.
Place all of the parts supplied on a at
surface. Form groups of the parts which
are similar.
Note: If connections are secured with a
bolt (round head/or hexagonal), hexago-
nal nuts and a washer, the washer must be
placed under the nut.
Insert the bolts from the outside to the in-
side in each case, securing the connections
with nuts from the inside.
Note: Tighten the nuts and bolts during as-
sembly only to the extent that they cannot
fall off.
If you tighten the nuts and bolts any further
before nal assembly, it is not possible for
nal assembly to be carried out.
Additional tool required:
- Phillips screwdriver
Mounting of the Frame
Abb.4-10
1. Turn the table circular saw over and
place it on the oor.
2. Unscrew the four mounted rubber feet
with a Phillips screwdriver (Figure 5).
3. Screw the four legs (18) with the
hexagon bolts (e) loosely on to the
saw (Figure 6). Use the jaw spanner
(r) supplied for this.
Caution! 2 of the legs have
holes (38) drilled into the rear,
into which the stand brackets
have to be xed. (Figures 6
and 10) Ensure that these are
attached at the rear of the ma-
chine.
4. Now take the cross struts (19) (marked
A) and longitudinal struts (20) (marked
B). Screw these loosely together with
the four central struts (21, 22) to the
legs. Mounting material: Round head
bolts (d), washer (a), spring washer (b)
and nuts (c), (Figure 6-8).
5. The round head bolts (d) and nuts (c)
should only be loosely tightened.
Caution: The longer struts
(marked B) must be used at the
side. Secure the central struts
with the hexagon bolts, as
shown in detail in Figure 8.
6. Now attach the rubber feet (23) to the
legs (Figure 9).
7. Screw the stand brackets (24) into the
rear legs using the drill holes. Moun-
ting material: 2 each: round head
bolts (d), shims (a), spring washer (b)
and nuts (c), (Figure 10).
1 8
G B
Caution! Both stand brackets
must be attached to the rear
of the machine at attachment
points 38!
8. Then tighten all of the bolts and nuts of
the base.
Mounting the table width
and length extension
(Figures 11-14)
1. Loosely tighten the table width extensi-
on (7) and table length extension (15)
on the saw table using the hexagon
bolts (f). (Figure 12).
2. Loosely tighten the table supports
(25, 26) on the housing of the table
circular saw using hexagon bolts (f). In
addition, the table supports (25, 26)
also have to be loosely tightened to
the table width and length extensions.
Mounting material: Hexagon bolts (e),
washer (a) and nut (c). The short sup-
ports (25) are for the table widening
extension, the long supports (26) for
the length extension, (Figures 13, 14).
3. Turn the saw over with the base and
place it on the oor.
4. Align the table width and length exten-
sion ush with the saw table.
5. Then tighten all bolts.
Mounting the Suction
Adapter
(Figure 15)
1. Insert the suction adapter (16) into
the opening provided on the rear of
the machine. The side outlet is now
pointing outwards.
2. The suction adapter has a rubber seal;
make sure that this is mounted.
3. The adapter is secured by means of
a bayonet lock. Insert the vacuum
cleaner adapter (16) as shown in
Figure 15 and lock this in place with a
quarter turn in a clockwise direction.
Mounting the Riving Knife
(Figures 16-19)
Caution! Remove the mains plug!
The setting of the saw blade (5)
must be checked whenever a blade
has been replaced.
1. Inserting the batteries (Figure 16):
- Turn the laser on/off switch (35) to the
0 position (laser off).
- Remove the battery compartment cover
(37) by loosening the screw (36).
Now remove the battery compartment
cover (37) by bending at the side.
- Insert the batteries supplied (type
AAA), ensuring the correct polarity
(see Figure 16).
- Put the battery compartment cover (37)
back in position and tighten it with
the screw (36). Notes concerning the
batteries:
- If you are not going to use the laser
for a prolonged period, please remove
the batteries from the battery com-
partment. Otherwise, the leaking of
battery uid might damage the device.
- Do not place the batteries on radia-
tors or expose them for a prolonged
period to strong sunlight; temperatures
above 50° could damage the device.
2. Adjust the saw blade (5) to a max.
cutting depth, move to the 0° position
and lock in place.
3. Release the screws (29). Remove the
table insert (6) (Figure 17).
1 9
G B
4. Release the two attachment bolts (30)
and insert the riving knife (4) between
the metal plate and the mount (see
Figure 18).
5. The distance between the saw blade
and riving knife (4) should be between
3 mm and max. 8 mm, (Figure 19).
6. Retighten the attachment bolts (30)
and mount the table insert (6) (see
Figure 17).
Mounting / dismounting
the Saw Blade Guard
(Figures 20/21)
1. Before initial assembly, the batteries
of the laser have to be inserted (see
Mounting the Riving Knife 1).
2. Dismantle the bolt with wing nut and
shim (27) of the saw blade guard (2).
Place the saw blade guard (2) from
the top onto the riving knife (4).
3. Mount the bolt with the wing nut and
shim (27) so that the bolt sits rmly in
the slot (28).
4. Do not overtighten the bolt (27). The
saw blade guard must be able to
move freely.
5. Place the suction hose (3) on the
suction adapter (16) and the suction
connector of the saw blade guard (2).
Connect a suitable woodchip extrac-
tion system to the suction adapter (16),
(Figure 21).
6. Dismantling is carried out in reverse
order. Caution! Before you start sa-
wing, the saw blade guard (2) has to
be lowered onto the item being sawn.
Replacing the Table Insert
(Figures 17 and 22)
1. If it is worn or damaged, the table in-
sert (6) has to be replaced, as otherwi-
se there is an increased risk of injury.
2. Remove the 3 countersunk screws (29).
3. Take out the worn table insert (6).
4. The new table insert is mounted in
reverse order.
Adjusting / mounting the
Riving Knife
(Figures 16-19)
Caution!
Remove the mains plug! The setting
of the saw blade (5) must be che-
cked whenever a blade has been
replaced.
1. Adjust the saw blade (5) to the max.
cutting depth, move to the 0° position
and lock in place.
2. Dismantle the saw blade guard (2)
3. Take out the table insert (6).
4. Loosen the attachment bolts (30).
5. Push the riving knife (4) upwards.
6. The distance between the saw blade
(5) and riving knife (4) should be max.
8 mm. (Figure 19)
7. Retighten the attachment bolts (30)
and mount the table insert (6).
8. Reattach the saw blade guard (2).
2 0
G B
Before putting into
operation
The machine must be set up on a sta-
ble surface, i.e. on the base or similar
item. For this, use the drill holes which
are located in the frame of the machi-
ne. For safe use on a work bench, four
mounted rubber feet are provided
(g. 5).
Before the machine is put into operati-
on, all covers and safety devices must
be properly attached.
The saw blade must be able to move
freely.
In the case of wood which has already
been worked with, check for foreign
bodies such as nails or screws etc.
Before pressing the on/off switch,
make sure that the saw blade is cor-
rectly attached and that moving parts
are free-running.
Before connecting the machine, check
that the data on the type plate matches
those of the mains system.
The machine must only be connected
to a properly installed safety socket
which is protected by a fuse of at least
16A.
If possible, connect the device only to
a socket with a residual current circuit
breaker (RCCB) with a tripping current
of not more than 30 mA.
Operation
Switching on and off
(Figure 23)
- The saw can be switched on by
pressing the green pushbutton „I“.
Before you start sawing, wait until the
saw blade has reached its maximum
speed.
Attaching/changing the
Saw Blade
(Figure 22)
1. Caution! Remove the mains
plug and wear protective
gloves.
2. Dismantle the saw blade guard (2).
3. Remove the table insert (6) by relea-
sing the three countersunk screws (29)
(see Figure 17)
4. Place the hexagon socket key (s) (HX
6) on the bolt and use the jaw spanner
(t) (SW 22) to stop the motor spindle
from turning (see Figure 22).
5. Caution! Turn the bolt in the direction
of rotation of the saw blade.
6. Remove the outer ange and take the
old saw blade off the inner ange by
pulling downwards and diagonally.
7. Clean the saw blade anges carefully
with a wire brush before attaching the
new saw blade.
8. Insert and tighten the new saw blade
in reverse order.
Caution! Note the direction of
motion; the slope of the cutting
edge of the teeth must face the
direction of motion, i.e. for-
wards (see the arrow on the
saw blade guard (2).
9. Reattach and adjust the table insert (6)
and the saw blade guard (2).
10. Before you work with the saw again,
a check must be carried out to ensure
that the protective devices are working
properly.
1 / 1

Parkside PTK 2000 B2 Translation Of The Original Instructions

Typ
Translation Of The Original Instructions

V iných jazykoch