Silvercrest SBTF 10 C3 Operating Instructions Manual

Bluetooth

®

HANDS-FREE KIT SBTF 10 C3

IAN 279754

HANDSFREE SÚPRAVA

S FUNKCIOU Bluetooth

®

Návod na obsluhu

Bluetooth

®

HANDSFREE

Használati utasítás

Bluetooth

®

-

FREISPRECH-

EINRICHTUNG

Bedienungsanleitung

Bluetooth

®

HANDS-FREE KIT

Operating instructions

Bluetooth

®

KIHANGOSÍTÓ

Használati utasítás

Bluetooth

®

NAPRAVA

ZA PROSTOROČNO

TELEFONIRANJE

Navodila za uporabo

GB Operating instructions Page 1

HU Használati utasítás Oldal 21

SI Navodila za uporabo Stran 41

CZ Návod k obsluze Strana 61

SK Návod na obsluhu Strana 81

DE / AT / CH Bedienungsanleitung Seite 101

Before reading, unfold the page containing the illustrations and

familiarise yourself with all functions of the device.

Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül

ismerje meg a készülék mindegyik funkcióját.

Pred branjem odprite stran s slikami in se nato seznanite z vsemi

funkcijami naprave.

Před čtením si otevřete stranu s obrázky a potom se seznamte se

všemi funkcemi přístroje.

Pred čítaním si odklopte stranu s obrázkami a potom sa oboznám-

te so všetkými funkciami prístroja.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus

und machen Sie sich anschließend mit allen Funktionen des

Gerätes vertraut.

SBTF 10 C3

GB

│

1 ■

Content

Correct Usage ................................. 2

Safety instructions .............................. 3

Introduction, trademark rights ..................... 5

Package contents (see fold-out page) ............... 6

Technical data ................................. 6

Controls (see fold-out page) ...................... 7

Installing the hands-free appliance in a vehicle ....... 7

Switching the hands-free appliance on and oﬀ ....... 8

Coupling the hands-free appliance with a mobile

telephone .................................... 8

Multipoint function ............................10

Pairing the hands-free kit with an additional mobile

phone ......................................10

Separating the connection ......................11

Using the hands-free appliance ..................11

Resetting the hands-free kit ......................14

Charging 5 V Devices ..........................14

Troubleshooting ...............................15

Cleaning and Care ............................16

Storage when not in use ........................16

Disposal ....................................17

Notes on the EU Declaration of Conformity .........17

Kompernass Handels GmbH warranty .............18

Service .....................................20

Importer ....................................20

SBTF 10 C3

■ 2

│

GB

Congratulations on the purchase of your new appliance.

You have clearly decided in favour of a quality product.

These operating instructions are a part of this product.

They contain important information in regard to safety, use

and disposal. Before using the product, familiarise your-

self with all of these operating and safety instructions. Use

the product only as described and only for the speciﬁed

areas of application. In addition, pass these documents

on, together with the product, to any future owner.

Correct Usage

The Bluetooth

®

hands-free device SBTF 10 C3 is an

information technology device intended for use in vehicles

supplying an on-board voltage of 12–24 V. The device is

designed to create an open voice connection with a mobile

phone via a Bluetooth

®

connection, in order to allow

the user to make telephone calls while travelling by car,

without having to hold the mobile phone to his or her ear.

The handsfree phone system uses both Bluetooth

®

radio

technology aswell as a digital signal processor (DSP) to

carry out telephone functions. In addition, mobile devices

with an operating voltage of 5V

(MP3 players, cell

phones, etc.) can be charged via the USB port*.

This device may be used ONLY for private domestic pur-

poses, not for industrial or commercial applications. This

product is not intended for use in activities concerned with

medicinal, lifesaving or life sustaining applications. All of

the additional connecting cables and external devices used

MUST match the safety-related, electromagnetic compata-

bility and shielding quality standards of the device at hand.

This appliance is not intended for any other use or for uses

beyond those mentioned. Claims of any kind for damage

resulting from unintended use will not be excepted. The

operator alone bears liability.

* USB

®

is a registered trademark of USB Implementers

Forum, Inc.

SBTF 10 C3

GB

│

3 ■

Safety instructions

Symbol deﬁnitions:

Danger!

A warning notice at this hazard level indicates a

potentially hazardous situation.

Failure to avoid this hazardous situation could result

in severe injuries and even death.

Ɣ Follow the instructions in this warning notice to

prevent injury.

Caution!

A warning notice at this hazard level indicates a

potential for property damage.

Failure to avoid this hazardous situation could result

in property damage.

Ɣ Follow the instructions in this warning notice to pre-

vent property damage.

Note:

Ɣ A note provides additional information that will assist

you in using the appliance.

Danger! Traﬃc safety has priority!

Ɣ Comply with all local laws. When driving, your hands

must ALWAYS be free to operate the vehicle safely.

Traﬃc safety must ALWAYS take priority whilst driving.

Ɣ Only manipulate the hands-free appliance on those

occasions in which the traﬃc situation permits it and in

which you will not endanger, injure, obstruct or cause

annoyance to other road users. Therefore you should

only operate the hands-free set in a stationary vehicle.

Ɣ Do not permit your concentration on the road traﬃc to

be compromised by the manipulation and displays of

the handsfree appliance!

Ɣ Become familiar with the operation of it before driving

oﬀ and practice the safe operation of the facility!

SBTF 10 C3

■ 4

│

GB

Ɣ Install the hands-free appliance in the vehicle such that

your view is not obstructed and that the appliance is

not located in an impact zone in the passenger com-

partment or in the inﬂation area of airbags. Read the

instruction manual of the vehicle manufacturer.

General safety instructions

Ɣ Do not attempt to open or repair the appliance. Should

you do so, appliance safety can no longer be assured

and the warranty becomes void.

Ɣ Have the defective device repaired by customer ser-

vice or an authorised specialist only. No liability will

be accepted for damage caused by misuse, improper

handling, use of force or unauthorized modiﬁcation.

Ɣ Never subject the device to moisture, extreme tempera-

tures (greater than +70°C) or extreme vibrations.

Ɣ This device is not intended for use by persons (including

children) with restricted physical, sensory or mental abili-

ties or lack of experience and/or knowledge unless, of

course, they are supervised by a person responsible for

their safety or obtain from that person instructions on

how the device should be used.

Danger!

Ɣ The packaging material is not a toy. Keep plastic sheeting,

bags and all other packaging material away from

children. There is a risk of suﬀocation.

Ɣ Children should be supervised to ensure that they do

not play with the device.

Attention

Ɣ Disconnect the device from the cigarette lighter socket

immediately if you notice any unusual sounds or smoke.

Caution! Pairing with a mobile phone

Ɣ If you wish to pair the device with a mobile phone,

read its operating instructions to obtain detailed safety

instructions relating to the mobile phone. Only pair

compatible products.

SBTF 10 C3

GB

│

5 ■

Caution! High frequency signals in

vehicles

HF signals can, under circumstances, negatively inﬂuence the

function of not properly installed or not suﬃciently shielded

electronic systems in vehicles, e.g. electronic ABS, electronic

tempo controllers and airbag systems. For further informa-

tion about your vehicle or its possible ancillaries make con-

tact with the respective manufacturer or their representative.

Introduction, trademark rights

Bluetooth

®

is a wireless communication system with

a short range. It makes possible wireless connections

between Bluetooth

®

appliances, such as for example

mobile telephones, PDA and PCs. Bluetooth

®

relates

itself to a worldwide standard for operation in the inter-

nationally recognised ISM Frequency Range (Industrial,

Scientiﬁc and Medical). Within the ISM Frequency Range

(2.402 - 2.480 GHz), a data transfer range of ca. 10 meters

(class II) is achieved. The disturbance susceptibility through

other users of the ISM Frequency Range, such as for

example microwaves, WLAN (802.11) or garage door

openers, is minimised by so-called “Frequency-Hopping“.

With Frequency-Hopping, a change of frequency levels

takes place at up to 1600 times per second, thereby

Bluetooth

®

is also reckoned to be relatively tap-proof.

However, data transferred via a radio link can be inter-

cepted by unauthorised third parties.

The Bluetooth

®

logotype and Bluetooth

®

logo are

registered trademarks of Bluetooth SIG, Inc. (Special

Interest Group). Any use of the trademarks by Kompernaß

Handels GmbH is made under the provisions of a licence.

All other names and brands are the property of their owner.

The HSP (Headset-Proﬁl) makes possible standard func-

tions such as voice transference, as well as the accept-

ance and rejection of calls.

The HFP (Handsfree-Proﬁl) makes possible the hands-free

call functions of a mobile telephone, for example with the

help of voice commands.

SBTF 10 C3

■ 6

│

GB

Package contents (see fold-out page)

Bluetooth

®

Hands-Free Kit

Operating instructions

Ɣ Take the device out of the packaging and remove all

packaging materials.

Note:

Ɣ Check the package for completeness and for signs of

visible damage.

Ɣ If any items are missing or damaged as a result of

defective packaging or insuﬃcient care during trans-

portation, contact the Service hotline (see the section

Service).

Technical data

Operating voltage/

current consumption: 12-24 V

/ 1000 mA

Bluetooth

®

Speciﬁcation: Version 3.0 + EDR,

up to a range of 10 meters

Supported Bluetooth

®

proﬁles: HSP and HFP

Output voltage/

max. power via USB port: 5 V

/ 1 A

Fuse: F2AL / 250 V

Dimensions: approx. 16.2 x 5.5 x 2.3 cm

Weight: approx. 78 g

Operational temperature: +5° to +40°C

Storage temperature: 0° to +70°C

Humidity: 5 to 75%

(no condensation)

SBTF 10 C3

GB

│

7 ■

Controls (see fold-out page)

 Vehicle connector plug

 Microphone

 +/- Buttons (Raise/lower the sound level)

 USB port

 Loudspeakers

 Multi-function button

 LED status indicator

Installing the hands-free appliance

in a vehicle

So that the hands-free appliance can function correctly, it

is connected to the vehicle cigar lighter socket or on-board

power socket and provided with electricity from there.

Ɣ Ensure that the hands-free appliance engages

completely and that the operation of the vehicle is

not negatively inﬂuenced. The hands-free set must be

easily accessible and the speaking distance kept to

a minimum. The LED status indicator  blinks twice

every 3 seconds and a short high signal tone sounds

once. The appliance is in standby mode.

Note:

It is possible that the cigar lighter only functions when the

vehicle ignition is switched on. In cases of doubt, consult

the operating instructions for the particular vehicle.

Caution!

For vehicles in which the cigar lighter, resp. the vehicle cir-

cuit plug, also functions when the ignition is switched oﬀ:

Ɣ Use the hands-free appliance only when the motor is

running. Otherwise, the vehicle batteries could become

discharged over an extended period of time.

Note:

When you are not using the hands-free equipment remove

it from the vehicles cigarette lighter socket. Store it in a dry,

dust free location protected from direct sunlight.

SBTF 10 C3

■ 8

│

GB

Switching the hands-free

appliance on and oﬀ

Switching on: The appliance is switched oﬀ.

Ɣ Press and hold the multi-function button for 3 sec-

onds, until a short and high signal tone is heard. The

LED status indicator  blinks twice every 3 seconds.

Note:

The hands-free set switches on automatically as soon as it

is connected to a power supply.

Switching oﬀ: The appliance is in standby mode.

Ɣ Press and hold the multi-function button  for 5 seconds,

until a long and deep signal tone is heard. The LED

status indicator  extinguishes.

Coupling the hands-free appliance

with a mobile telephone

The hands-free appliance has been especially developed

for mobile telephones that support the Bluetooth

®

Proﬁle

“Handsfree (HFP) and Headset (HSP)“. Further informa-

tion about Bluetooth

®

radio technology is to be found

in the operating instructions for your mobile telephone.

Before you can use the hands-free appliance, you must

connect it with a compatible mobile telephone (pairing).

Ɣ Check to make sure the mobile telephone is switched on.

Ɣ Programme the mobile telephone so that it searches

for Bluetooth

®

appliances. A detailed description of

how to do this is to be found in the operating instruc-

tions for your mobile telephone.

Ɣ Ensure that the hands-free appliance is correctly set up

and switched oﬀ.

Ɣ To switch the device oﬀ, press and hold the multi-function

button  for about 5 seconds. A long, low signal

tone will be heard and the LED status indicator 

extinguishes.

SBTF 10 C3

GB

│

9 ■

Ɣ Position the hands-free appliance and the mobile tele-

phone so that they are not more than 1 metre away

from each other.

Ɣ Press and hold down the multi-function button  for 6

seconds until, after 3 seconds a short, high signal tone

and after a further 3 seconds a succession of low and

high signal tones are heard. The LED status indicator

 lights up constantly and the hands-free equipment is

now in the coupling mode.

Ɣ Select the hands-free provision “Car Kit“ from the list

of available appliances for the mobile telephone.

Ɣ Enter in the pre-programmed passcode “9999“ and

then conﬁrm it, which couples the appliances with

each other. You will hear a short, high-pitched beep

followed by a short low beep and the LED status

indicator  ﬂashes every 3 seconds.

Ɣ You can now use the hands-free appliance.

Note:

When using the latest mobile phones, (Smartphones) those

that are equipped with Bluetooth

®

2.0 or a more mod-

ern version, it is possible that the pass code “9999“ need

not be entered. If the coupling is not completed within 2

minutes, the hands-free appliance switches itself oﬀ. The

LED status indicator  extinguishes and you will hear a

long and deep signal tone. With some mobile telephones

it is possible that coupling does not automatically take

place. In this case coupling must be carried out addition-

ally on the mobile telephone. The LED status indicator 

blinks twice every 3 seconds until this has been carried

out. Further information can be found in your mobile

telephone’s operating instructions.

SBTF 10 C3

■ 10

│

GB

Multipoint function

The multipoint function allows you to use the hands-free kit

with two mobile phones simultaneously. This is useful for

users with a private and a business mobile phone.

If you have paired several mobile phones, the hands-free

kit will now have several “known” devices available. This

status is a prerequisite for an active connection between

the hands-free kit and other mobile phones. A maximum

of 8 mobile phones can be saved as “known” devices.

The number of devices that can be actively linked to the

hands-free kit is limited to two. As soon as one or two of

the known devices come into range of the hands-free kit,

connection to the devices is made automatically. In some

cases, you must conﬁrm the connection manually on your

mobile phone.

If a third “known” device comes into range of the hands-

free kit, the connection to this device will remain blocked

until one of the two active connections is broken or one

of the two devices leaves the transmission range. If the

connection of one of the paired devices is broken, the

link becomes free for the third (waiting) device.

If two mobile phones are connected to the hands-free

kit, the ring tone will sound from the phone itself and not

the hands-free kit when there is an incoming call to the

second mobile phone.

Pairing the hands-free kit with an

additional mobile phone

Ɣ Make sure that the ﬁrst mobile phone is not connected

to the hands-free kit.

Ɣ Switch oﬀ the hands-free kit by pressing the multifunction

button  for about 5 seconds. You will hear a long,

low beep and the LED status indicator  goes out.

Ɣ Press and hold the multifunction button  for about

6 seconds. After 3 seconds, you will hear a short

high-pitched beep followed 3 seconds later by another

high-pitched beep. The LED status indicator  lights

up permanently.

SBTF 10 C3

GB

│

11 ■

Ɣ Select the “Car Kit” hands-free kit from the list of

available devices on the mobile phone.

Ɣ Enter the preset pass code “9999” and then conﬁrm

this to pair the devices with each other. You will hear

a short, low beep followed by a short, high-pitched

beep and the LED status indicator ﬂashes every

3 seconds.

Ɣ Switch oﬀ the hands-free kit after successfully pairing

the second mobile phone.

Ɣ Press and hold the multifunction button  for about

3 seconds until you hear a short high-pitched beep. The

LED status indicator  ﬂashes twice every 3 seconds.

The hands-free kit will attempt to make a connection to

the last two connected mobile phones within the next few

seconds. You will hear a double beep once the devices

have been successfully paired.

Note:

In some cases, it will be necessary to make the connection

manually via the Bluetooth

®

menu on the mobile phone.

Separating the connection

If you wish separate the mobile telephone from the hands-

free appliance, for example, to connect it to another

Bluetooth

®

appliance:

Ɣ Switch the hands-free appliance oﬀ

or

Ɣ separate the connection over the Bluetooth

®

menu

in the mobile telephone.

Note:

You need not erase the coupling with the hands-free appli-

ance in the Bluetooth

®

menu to separate the connection.

Using the hands-free appliance

After successful coupling, the following functions are

available to you. Some of the described functions are

only possible with a mobile telephone that supports the

Handsfree Proﬁle (HFP).

SBTF 10 C3

■ 12

│

GB

Note:

The sound quality of the hands-free set is heavily depend-

ent on where it is installed. Where possible, set up your

hands-free set so that the microphone  is pointing in

your direction.

Call function

Ɣ Use your mobile telephone in the usual way to make a call.

Ɣ For redialing of the last number called, shortly press

the multi-function button  twice.

Ɣ For activation of voice dialling, shortly press the multi-

function button  once.

Note:

Voice dialing is only available with mobile telephones that

support this function. Further information regarding voice

dialing is to be found in the operating instructions for your

mobile telephone.

Accepting and ending a call

When you receive a call the LED status indicator  blinks

and you hear a call tone from the hands-free appliance.

If the call signal in your mobile phone is switched oﬀ, the

ringing tone is nonetheless sounded via the hands-free

appliance.

Ɣ Press the multi-function button  shortly once,

to accept the call.

Ɣ Press the multi-function button  shortly once,

to terminate the accepted call.

You can also accept and terminate the call over the

mobile telephone.

SBTF 10 C3

GB

│

13 ■

Managing calls

If you have connected two mobile phones to the hands-

free kit simultaneously, you can put one call on hold in

order to take a call from a second mobile phone and

toggle between the two calls.

Note:

If a call comes to the second mobile phone during an

ongoing call, this call will only be signalled on the

second phone.

Ɣ Press the multifunction button  twice brieﬂy to accept

the call on the second mobile phone while already

talking on the ﬁrst mobile phone. The ﬁrst call is put

on hold.

Ɣ Press the multifunction button  again twice to toggle

between the two calls. When the current call is ﬁnished,

the hands-free kit switches automatically to the second

ongoing call.

Ɣ Press the multifunction button  once brieﬂy to end the

current call and automatically accept the second call.

Automatic call acceptance

If automatic call acceptance is activated in the mobile tel-

ephone, it accepts the incoming call after a determined time

period and then passes it on to the hands-free appliance. Fur-

ther information regarding automatic call acceptance is to be

found in the operating instructions for your mobile telephone.

Rejecting a call

Ɣ Press the multifunction button  for about 3 seconds

to reject an incoming telephone call.

Adjusting the volume of the hands-free appliance

You can adjust the sound volume level of the hands free

device with the +/- buttons .

Ɣ During a conversation, press the + or - button  until the

desired volume level is set. A high-pitched beep signals

that you have reached maximum volume; a low-pitched

beep signals that you have reached minimum volume.

SBTF 10 C3

■ 14

│

GB

Resetting the hands-free kit

The hands-free kit can be paired with up to 8 mobile

phones. To delete the pairing list and reset the hands-free

kit to the factory defaults, proceed as follows:

Ɣ Ensure that the hands-free kit is in standby mode.

Ɣ Press and hold the multifunction button  for about

10 seconds until you hear two beeps and the LED

status indicator  ﬂashes ﬁve times. The pairing list

is deleted and the hands-free kit is reset to the factory

defaults.

Note:

After resetting to the factory default settings, the hands-

free kit will automatically be in pairing mode when it is

connected to a mobile phone.

If the hands-free kit is not connected to a mobile phone

after resetting to the factory defaults it will be in standby

mode.

Charging 5 V Devices

Ɣ Check the max. input voltage (5V) and the max. power

input (1000 mA) of the device which you want to charge.

For this, consult the operating manual of the device.

Ɣ Connect the device to be charged with the USB port 

on the hands free device. The device now receives its

power supply from the hands free device. If the device

is equipped with a charging indicator light, this will in-

dicate that the device is being charged.

Note:

If the power supply does not activate automatically, you

should disconnect the USB cable from the USB port 

and re-connect it.

SBTF 10 C3

GB

│

15 ■

Troubleshooting

If you cannot connect the hands-free appliance with a

compatible mobile telephone, proceed as follows:

Ɣ Ensure that the Bluetooth

®

function in the mobile

telephone is activated.

Ɣ Is the display ﬂashing? Ensure that the hands-free ap-

pliance is correctly installed, switched on and supplied

with electricity.

Ɣ If you use several Bluetooth

®

appliances, ensure that

a previously created Bluetooth

®

connection of the

mobile telephone is separated. This may indicate that

a previously paired device is in range.

Ɣ Ensure that the hands-free appliance is distanced a ma-

ximum of 10 metres from the mobile telephone and that

there are no barriers or electronic devices between them.

Replacing the fuse

The hands-free set is equipped with a fuse. If the device

no longer works, check the fuse and replace if necessary.

Ɣ Open the vehicle connector plug  by turning the

ﬂuted screw insert

A

gently anticlockwise – with pliers

if necessary – and remove it.

Ɣ Remove the plug tip

B

from the fuse

C

and pull the fuse

out. Ensure that the spring

D

in the vehicle connector

plug  does not accidentally jump out and become lost.

Ɣ Place a new fuse of type F2AL/250V into the vehicle

connector plug , place the plug tip

B

onto the end

of the fuse that is slightly protruding

C

and screw the

screw insert that you removed earlier

A

back in.

D

C B A

SBTF 10 C3

■ 16

│

GB

Danger!

Ɣ Replace the fuse only with another of the same rating

as that given on the ratings plate. Fuses with a diﬀerent

rating may cause ﬁre. Smoke resulting from such a ﬁre

is poisonous.

Note:

If these measures do not correct the problem, please con-

tact the appropriate service partner for your country.

Cleaning and Care

Danger of electrocution!

Ɣ Before cleaning, always separate the electricity supply

from the appliance!

Ɣ NEVER submerse the appliance in water or other liquids!

Ɣ Do not permit liquids to permeate into the housing!

Ɣ Never open the housing of the appliance! There are

no user-serviceable elements inside.

Ɣ Do not use strong detergents, solvents or abrasive

cleaning agents to clean the appliance. These could

damage the housing surfaces.

Ɣ Clean the housing surfaces with a slightly moist soft cloth.

Storage when not in use

Caution!

The temperatures inside the vehicle can reach extreme values

in summer and winter. Consequently, to avoid damage to

the device, you should not store it in the vehicle.

Ɣ Store the device somewhere clean, dry, free of dust

and out of direct sunlight.

SBTF 10 C3

GB

│

17 ■

Disposal

The adjacent symbol of a crossed-out wheelie

bin indicates that this device is subject to

Directive 2012/19/EU. This directive states that

this device may not be disposed of in the

normal household waste at the end of its useful life, but

must be handed over to specially set-up collection

locations, recycling depots or disposal companies.

This disposal is free of charge for the user.

Protect the environment and dispose of this

device properly.

You can obtain further information from your local dis-

posal company or the city or local authority.

Dispose of all packaging materials in an

environmentally responsible manner.

Notes on the EU Declaration

of Conformity

This appliance complies with the essential requirements and

other relevant provisions of the R&TTE Directive 1999/5/EC,

the Automotive EMC Directive 2004/104/EC, the Low

Voltage Directive 2014/35/EU and the RoHS Directive

2011/65/EU.

You can request the full EU Declaration of conformity from

the importer.

Stránka sa načítava ...

Silvercrest SBTF 10 C3 Operating Instructions Manual

Táto príručka je tiež vhodná pre

Silvercrest SBTF 10 C3 Operating Instructions Manual

V iných jazykoch

Súvisiace články

Ďalšie dokumenty