Stránka sa načítava...
VT100DIG
Digital radio link
Installation and Operating Manual . . . . . . 7
Digitale Funkstrecke
Montage- und Bedienungsanleitung . . . 19
Systéme radio numérique
Instructions de montage
et de service . . . . . . . . . . . . . . . . . . . . . . . 32
Tramo de transmisión por radio
digital
Instrucciones de montaje y de uso . . . . .45
Percurso digital
Instruções de montagem e manual de
instruções . . . . . . . . . . . . . . . . . . . . . . . . . 58
Tratta radio digitale
Istruzioni di montaggio e d’uso . . . . . . . . 71
Digitaal zendbereik
Montagehandleiding en
gebruiksaanwijzing. . . . . . . . . . . . . . . . . . 84
Digital trådløs forbindelse
Monterings- og betjeningsvejledning. . . 97
Digital radiolänk
Monterings- och bruksanvisning . . . . . . 109
Digital radiolink
Monterings- og bruksanvisning . . . . . . .121
Digitaalinen radiolinkki
Asennus- ja käyttöohje. . . . . . . . . . . . . . 133
Устройство цифровой
радиосвязи
Инструкция по монтажу
и эксплуатации. . . . . . . . . . . . . . . . . . . . 146
Cyfrowe łącze radiowe
Instrukcja montażu i obsługi . . . . . . . . . 160
Digitálne rádiorelé spojenie
Návod na montáž a uvedenie
do prevádzky . . . . . . . . . . . . . . . . . . . . . 173
Zařízení k přenosu digitálního
rádiového signálu
Návod k montáži a obsluze . . . . . . . . . . 186
Digitális rádiós szakasz
Szerelési és használati útmutató . . . . . . 198
EN
DE
FR
ES
PT
IT
NL
DA
SV
NO
FI
RU
PL
SK
CS
HU
DRIVING SUPPORT
PERFECTVIEW
VT100DIG-IO-16s.book Seite 1 Montag, 1. August 2016 2:46 14
VT100DIG-IO-16s.book Seite 2 Montag, 1. August 2016 2:46 14
VT100DIG
3
1
2
3
4
9
6 8
5
7
10
11
12
1
VT100DIG-IO-16s.book Seite 3 Montag, 1. August 2016 2:46 14
VT100DIG
4
2
3
2.
1.
1.
4
12
5
VT100DIG-IO-16s.book Seite 4 Montag, 1. August 2016 2:46 14
VT100DIG
5
65
7 8
4
1
2
3
6
1
2
3
5
6
4
7
VT100DIG-IO-16s.book Seite 5 Montag, 1. August 2016 2:46 14
VT100DIG
6
8
9
VT100DIG-IO-16s.book Seite 6 Montag, 1. August 2016 2:46 14
VT100DIG Explanation of symbols
EN
7
Please read this instruction manual carefully before installation and first use, and store
it in a safe place. If you pass on the product to another person, hand over this instruc-
tion manual along with it.
Table of contents
1 Explanation of symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2 Safety and installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5 Technical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
6 Installing the radio link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7 Connecting electrical power to the radio link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
8 Pairing the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
9 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
10 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
11 Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
12 Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
1 Explanation of symbols
!
!
A
I
WARNING!
Safety instruction: Failure to observe this instruction can cause fatal or serious injury.
CAUTION!
Safety instruction: Failure to observe this instruction can lead to injury.
NOTICE!
Failure to observe this instruction can cause material damage and impair the function
of the product.
NOTE
Supplementary information for operating the product.
VT100DIG-IO-16s.book Seite 7 Montag, 1. August 2016 2:46 14
Safety and installation instructions VT100DIG
EN
8
2 Safety and installation instructions
The manufacturer accepts no liability for damage in the following cases:
• Damage to the product resulting from mechanical influences and excess voltage
• Alterations to the product without express permission from the manufacturer
• Use for purposes other than those described in the operating manual
Please observe the prescribed safety instructions and stipulations from the vehicle
manufacturer and service workshops.
!
WARNING!
Inadequate supply cable connections could result in short circuits, which could have as
a consequence that:
• Cable fires occur
• The airbag is triggered
• Electronic control devices are damaged
• Electric functions fail (indicators, brake light, horn, ignition, lights)
A
NOTICE!
To prevent the risk of short circuits, always disconnect the negative terminal of the vehi-
cle's electrical system before working on it.
If the vehicle has an additional battery, its negative terminal should also be discon-
nected.
Please observe the following instructions:
• When working on the following cables, only use insulated cable lugs, plugs and flat push-on
receptacles:
– 30 (direct supply from positive battery terminal)
–15 (connected positive terminal, behind the battery)
– 31 (return line from the battery, earth)
– L (indicator lights left)
– R (indicator lights right)
Do not use terminal strips.
• Use a crimping tool to connect the cables.
• When connecting to cable 31 (earth), screw the cable
– to the vehicle's earth bolt with a cable lug and a gear disc or
– to the sheet-metal bodywork with a cable lug and a self-tapping screw.
Ensure that there is a good earth connection.
VT100DIG-IO-16s.book Seite 8 Montag, 1. August 2016 2:46 14
VT100DIG Safety and installation instructions
EN
9
If you disconnect the negative terminal of the battery, all data stored in the volatile memories will
be lost.
• The following data must be set again, depending on the vehicle equipment options:
–Radio code
– Vehicle clock
–Timer
– On-board computer
– Seat position
You can find instructions for making these settings in the appropriate operating instructions.
Observe the following installation instructions:
!
CAUTION!
• Secure the parts installed in the vehicle in such a way that they cannot become loose
under any circumstances (sudden braking, accidents) and cause injuries to the
occupants of the vehicle.
• Secure any parts of the system covered by the bodywork in such a manner that they
cannot be come loose or damage other parts and cables or impair vehicle functions
(steering, pedals, etc).
• Always follow the safety instructions of the vehicle manufacturer.
Some work (e.g. on retention systems such as the AIRBAG etc.) may only be per-
formed by qualified specialists.
A
NOTICE!
• To prevent damage when drilling, make sure there is sufficient space on the other
side for the drill head to come out.
• Deburr all drill holes and treat them with a rust-protection agent.
Observe the following instructions when working with electrical parts:
A
NOTICE!
• When testing the voltage in electrical cables, only use a diode test lamp or a voltme-
ter.
Test lamps with an illuminant take up voltages which are too high and which can dam-
age the vehicle's electronic system.
• When making electrical connections, ensure that:
– they are not kinked or twisted
– they do not rub on edges
– they are not laid in sharp edged ducts without protection.
• Insulate all connections.
• Secure the cables against mechanical wear with cable binders or insulating tape,
for example to existing cables.
VT100DIG-IO-16s.book Seite 9 Montag, 1. August 2016 2:46 14
Scope of delivery VT100DIG
EN
10
3Scope of delivery
4Intended use
The PerfectView VT100DIG radio link (ref. no. 9600000068) is used for the wireless transmission
of signals between the camera and the monitor for the PerfectView reversing video systems from
2011.
5 Technical description
5.1 Function description
The radio link consists of a transmitter module and a receiver module. The two modules can be
mounted inside or outside the vehicle. They transmit pictures and sound wirelesssly from the
camera to the monitor.
The transmitter module is preferably supplied with a voltage via the ignition plus and is also used
to supply the camera with a voltage. When connecting only with the reversing light, the system
pairing cannot be started in reverse gear.
The receiver module is powered by the monitor. The wireless signals are transmitted in the
2.4 GHz range.
Since the system is designed merely as an additional aid for reversing, it does not relieve you of
the duty to take proper care when reversing.
A
No. in
fig. 5, page 4
Quantity Description
1 1 Transmitter module
21Receiver module
––Fastening material
NOTICE!
• VT100DIG transmits digital data. The data is displayed on the monitor 0.2 s after it
is recorded by the camera. Therefore, it is essential that you drive slowly.
• If the monitor displays a yellow warning triangle, there is a fault in the picture
transmission. It is possible that the display of the camera image on the monitor is
delayed. Therefore the system may not be used as an aid during reversing in such
circumstances.
VT100DIG-IO-16s.book Seite 10 Montag, 1. August 2016 2:46 14
VT100DIG Technical description
EN
11
5.2 Control elements
You will find the following control elements on the transmitter module:
The receiver module has the following control elements:
No. in
fig. 6, page 5
Meaning
1 Antenna connection
2 Pairing button
3 Operating mode display:
• LED glows red when signals are being transmitted
• LED flashes red when the components are being paired
4 Camera connection
5 Blue cable (CAMERA POWER TRIGGER): voltage supply for camera and
switch input for protective cover of CAM80 (see page 15)
6 Green cable (REVERSE TRIGGER): control cable for activating the pairing
signal
7 Red cable (DC INPUT): Connection to the positive terminal of the
voltage supply; preferably ignition plus
8 Black cable (GND): Connection to the negative terminal of the voltage
supply or earth
No. in
fig. 7, page 5
Meaning
1 Antenna connection
2 Pairing button
3 Operating mode display:
• LED glows red when signals are being transmitted
• LED flashes red when the components are being paired
4 Monitor connection
5 Green cable (REVERSE TRIGGER): control cable for activating the pairing
signal
6 Black cable (GND): Connection to earth
VT100DIG-IO-16s.book Seite 11 Montag, 1. August 2016 2:46 14
Installing the radio link VT100DIG
EN
12
6 Installing the radio link
6.1 Tools required
For installation and assembly, you will need the following tools:
• Drill bit set (fig. 1 1, page 3)
• Electric drill (fig. 1 2, page 3)
• Screwdriver (fig. 1 3, page 3)
• Set of ring or open-ended spanners (fig. 1 4, page 3)
• Measuring ruler (fig. 1 5, page 3)
• Hammer (fig. 1 6, page 3)
• Centre punch (fig. 1 7, page 3)
To establish and test the electrical connection, the following tools are required:
• Diode test lamp (fig. 1 8, page 3) or voltmeter (fig. 1 9, page 3)
• Crimping tool (fig. 1 10, page 3)
• Insulating tape (fig. 1 11, page 3)
• Cable bushing sleeves (optional)
To fasten the module and the cables, you may need additional screws and cable binders.
6.2 Installing the modules
!
Observe the following installation instructions:
• Install the modules so that as few objects as possible are between them.
Metal objects in particular can hinder radio transmission.
• If possible, install the modules in the vehicle.
The housings are splash-water protected and can be mounted outside the vehicle. In this
case, you need to select a location that is protected against mechanical impacts (e.g. flying
stones).
• The installation location should be flat.
• Before drilling, check each time that there is sufficient space on the other side for the drill head
to emerge (fig. 2, page 4).
• Transmitter module: Make sure you can lay the connection cable to the camera.
• Receiver module: Make sure you can lay the connection cable to the monitor.
CAUTION!
Select the location of the modules so that they cannot injure the passengers in the
vehicle under any circumstances (e.g. sudden braking, road traffic accidents).
VT100DIG-IO-16s.book Seite 12 Montag, 1. August 2016 2:46 14
VT100DIG Connecting electrical power to the radio link
EN
13
I
To perform the installation, proceed as follows:
➤ Attach the modules temporarily to the planned installation location.
➤ Install the rear view video system if you have not already done so.
➤ Start up the rear view video system.
If the camera image transmission is stable (two or three reception bars at the top right of the
monitor), you can complete final installation of the two modules.
If faults occur (only one reception bar or a yellow warning triangle on the top right of the
monitor) turn or move the transmitter or receiver module slightly and conduct further tests.
Attaching the modules (fig. 8, page 6)
To do this, proceed as follows for each module:
➤ Hold the module at the chosen location and mark the four points for drill holes.
➤ Drill holes with a Ø of 4 mm at each of the points you just marked.
➤ Screw the module on with M5 x 20mm self-tapping screws.
Fixing the antennas (fig. 9, page 6)
I
➤ You can glue the antennae on the corresponding module.
7 Connecting electrical power to the radio link
7.1 General notes on laying cables
I
NOTE
Pictures and sound are sent from the transmitter module to the receiver module. To
ensure flawless functioning, you need to check whether the wireless transmission is
stable before final installation.
NOTE
Always align the antennas in the same direction, for example, both vertically.
This improves the transmission performance.
NOTE
• As far as possible, use original ducts for laying the cables, or other suitable options
such as panelling edges, ventilation grilles or dummy plugs. If no openings are avail-
able, you must drill holes for the cables. Check beforehand that there is sufficient
space on the other side for the drill head to emerge.
• Cables and connections that are not properly installed will cause malfunctions or
damage to components. Correct installation of cables and connections ensures
lasting and trouble-free operation of the retrofitted components.
VT100DIG-IO-16s.book Seite 13 Montag, 1. August 2016 2:46 14
Connecting electrical power to the radio link VT100DIG
EN
14
Therefore, please observe the following instructions:
• Wherever possible, lay cables inside the vehicle, as they are better protected there than
outside.
If you do need to lay a cable outside the vehicle, ensure that it is well fastened (use additional
cable ties, insulating tape etc.).
• To prevent damage to the cables when laying them, ensure that they are far enough away from
hot or moving vehicle components (exhaust pipes, drive shafts, light systems, fans, heaters
etc.).
• Screw on the plug connections of the connecting cables to protect against water penetration
(fig. 4, page 4).
• When laying the cables, make sure:
– they are not kinked or twisted
– they do not rub on edges
– they are not laid in sharp-edged ducts without protection (fig. 3, page 4).
• Protect every through-hole made in the bodywork against water penetration, e.g. by using a
cable with a sealant and by spraying the cable and the cable sleeve with sealant.
I
7.2 Connecting electrical power to the transmitter module
A
VT100DIG requires a few seconds to initiate the digital wireless connection. To keep this start-up
time short, you should connect the transmitter module to an active +12 V voltage supply. If no
continuous operating voltage is available, you can connect the transmitter module to the reversing
light.
Connecting the transmitter module to a continuous operating voltage
➤ Connect the red cable of the transmitter module (fig. 6 7, page 5) to an active positive cable,
e.g. terminal 15.
➤ Connect the black cable of the transmitter module (fig. 6 8, page 5) to earth (bodywork).
➤ Connect the green cable of the transmitter module (fig. 6 6, page 5) to the reversing light.
A
NOTE
Only start sealing through-holes when you have completed all installation work on the
camera and have laid the required cable lengths.
NOTICE!
Make sure the polarity is correct.
NOTICE!
Always connect the green cable to the reversing light and not to a continuous
operating voltage or an active positive cable. The "pairing" is started via this cable by
engaging the reverse gear three times.
VT100DIG-IO-16s.book Seite 14 Montag, 1. August 2016 2:46 14
VT100DIG Connecting electrical power to the radio link
EN
15
➤ Connect the blue cable of the transmitter module (fig. 6 5, page 5) depending on the type
of camera.
– Camera without motorised protective cover to an active positive cable
– Camera with motorised protective cover to the reversing light
➤ Connect the camera connector (fig. 6 4, page 5) to the camera.
Connecting the transmitter module to the reversing light (no continuous operating
voltage)
I
➤ Connect the red cable of the transmitter module (fig. 6 7, page 5) to the positive wire (+) of
the reversing light.
➤ Connect the black cable of the transmitter module (fig. 6 8, page 5) to the earth wire (–) of
the reversing light or to earth (bodywork).
➤ Connect the blue cable of the transmitter module (fig. 6 5, page 5) to the positive wire of the
reversing light.
➤ Connect the camera connector (fig. 6 4, page 5) to the camera.
A
7.3 Connecting electrical power to the receiver module
➤ Connect the green cable of the receiver module (fig. 7 5, page 5) to the reversing switch.
➤ Connect the black cable of the receiver module (fig. 7 6, page 5) to earth (bodywork).
➤ Connect the monitor connector (fig. 7 4, page 5) to the monitor.
➤ Switch on the monitor.
✓ The monitor displays the message “Wait Tx Signal …”.
NOTE
• These connection options only work with the cameras CAM50C, CAM60CM or
CAM30C.
• On some vehicles, the reversing light only works when the ignition is switched on.
In this case, you must switch on the ignition in order to identify the positive and earth
wires.
• If the transmitter module is only connected via the reversing light, the system pairing
cannot be started in the reverse gear.
NOTICE!
The green cable may not be used.
Pairing the transmitter and receiver is only possible when reverse gear is engaged via
the button!
VT100DIG-IO-16s.book Seite 15 Montag, 1. August 2016 2:46 14
Pairing the system VT100DIG
EN
16
8 Pairing the system
I
8.1 Pairing the system manually with the pairing button
➤ Press the pairing button on the receiver module (fig. 7 2, page 5) three times within 10 s
(press the button approx. 1 time per second).
✓ The LED on the receiver module (fig. 7 3, page 5) flashes red.
✓ The monitor displays the message “Pairing Start” and a counter that counts down 50 s.
You need to perform the pairing of the transmitter module within 50 s.
➤ Press the pairing button on the transmitter module (fig. 6 2, page 5) three times within 10 s
(press the button approx. 1 time per second).
✓ The LED on the transmitter module (fig. 6 3, page 5) flashes red.
✓ The modules synchronise themselves with each other.
This takes approx. three to five seconds. For successful pairing, the monitor shows the “Save
data” message and the picture appears.
If pairing is unsuccessful, the monitor displays the message “Pairing Failed”. Repeat
the pairing procedure.
8.2 Pairing the system with reverse gear
You can start pairing the module via the reverse gear if you connect the red cable from the trans-
mitter module to the positive terminal and the green cable of both modules on the reversing light.
➤ Switch on the monitor.
➤ Activate the required channel.
➤ Engage and disengage the reverse gear three times within 10 s.
✓ The LED on the transmitter module (fig. 6 3, page 5) and the LED on the receiver module
(fig. 7 3, page 5) flash red.
✓ The modules synchronise themselves with each other.
This takes approx. three to five seconds. For successful pairing, the monitor shows the “Save
data” message and the picture appears.
If pairing is unsuccessful, the monitor displays the message “Pairing Failed”. Repeat
the pairing procedure.
NOTE
The transmitter module and the receiver module have to be paired with each other so
that the monitor can display the camera images. This is conducted at the factory.
VT100DIG-IO-16s.book Seite 16 Montag, 1. August 2016 2:46 14
VT100DIG Troubleshooting
EN
17
9 Troubleshooting
10 Warranty
The statutory warranty period applies. If the product is defective, please contact the
manufacturer's branch in your country (see the back of the instruction manual for the addresses) or
your retailer.
For repair and guarantee processing, please include the following documents when you send in
the device:
• A copy of the receipt with purchasing date
• A reason for the claim or description of the fault
Fault Cause Suggested remedy
The monitor displays the
message “NO SIGNAL”.
The transmitter module is
not working.
Check the voltage supply.
The monitor displays the
message “REVERSE
FOR IMAGE”.
The green and the blue
cable are incorrectly con-
nected.
Check the camera connection and
function.
The transmitter module is
not receiving a video sig-
nal.
The monitor displays the
message “Pairing
Failed”.
The start signal (on/off
three times) is incomplete
or missing.
Repeat the system pairing until the
monitor displays “Save data”.
The monitor displays the
message “wait for
TX”.
Transmitter and receiver
modules have lost identi-
fication.
Engage reverse gear again.
Start system pairing.
The transmitter module
has no voltage supply.
Check the voltage supply.
Irregular image playback
or yellow warning triangle
on the screen.
– Make sure that the antennae of the
receiver module and the transmitter
module are firmly connected.
Check the reception bars on the moni-
tor. If only one reception bar is dis-
played, change the position of the
transmitter or receiver module.
Check if the battery charge is sufficient.
VT100DIG-IO-16s.book Seite 17 Montag, 1. August 2016 2:46 14
Disposal VT100DIG
EN
18
11 Disposal
➤ Place the packaging material in the appropriate recycling waste bins wherever possible.
M
If you wish to finally dispose of the product, ask your local recycling centre or specialist
dealer for details about how to do this in accordance with the applicable disposal
regulations.
12 Technical data
Approvals
The appliance has E13 certification.
VT100DIG
Ref. no.: 9600000068
Frequency: 2.400–2.483 GHz
Transmission output of transmitter module: 10 mW
Reception delay: < 200 ms
Range: 120 m, free field
Channel raster: 18.9 MHz
Frame rate: max. 30 frames/s
Operating temperature: –20 °C to +60 °C
Operating voltage: 12–30 Vg
Current consumption
Transmitter module (without camera)
Receiver module:
approx. 130 mA
approx. 100 mA
Protection class: IP65
Dimensions (W x H x D) (without antenna): 115 x 110 x 26 mm
Weight: 220 g
13
1622
10R-0412874
VT100DIG-IO-16s.book Seite 18 Montag, 1. August 2016 2:46 14
VT100DIG Erklärung der Symbole
DE
19
Bitte lesen Sie diese Anleitung vor Einbau und Inbetriebnahme sorgfältig durch und
bewahren Sie sie auf. Geben Sie sie im Falle einer Weitergabe des Produktes an den
Nutzer weiter.
Inhaltsverzeichnis
1 Erklärung der Symbole. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2 Sicherheits- und Einbauhinweise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
3 Lieferumfang . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
4 Bestimmungsgemäßer Gebrauch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
5 Technische Beschreibung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
6 Funkstrecke montieren . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
7 Funkstrecke elektrisch anschließen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
8 System abgleichen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
9 Störungsbeseitigung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
10 Gewährleistung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
11 Entsorgung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
12 Technische Daten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
1 Erklärung der Symbole
!
!
A
I
WARNUNG!
Sicherheitshinweis: Nichtbeachtung kann zu Tod oder schwerer Verletzung führen.
VORSICHT!
Sicherheitshinweis: Nichtbeachtung kann zu Verletzungen führen.
ACHTUNG!
Nichtbeachtung kann zu Materialschäden führen und die Funktion des Produktes
beeinträchtigen.
HINWEIS
Ergänzende Informationen zur Bedienung des Produktes.
VT100DIG-IO-16s.book Seite 19 Montag, 1. August 2016 2:46 14
Sicherheits- und Einbauhinweise VT100DIG
DE
20
2 Sicherheits- und Einbauhinweise
Der Hersteller übernimmt in folgenden Fällen keine Haftung für Schäden:
• Beschädigungen am Produkt durch mechanische Einflüsse und Überspannungen
• Veränderungen am Produkt ohne ausdrückliche Genehmigung vom Hersteller
• Verwendung für andere als die in der Anleitung beschriebenen Zwecke
Beachten Sie die vom Fahrzeughersteller und vom Kfz-Handwerk vorgeschriebenen
Sicherheitshinweise und Auflagen!
!
WARNUNG!
Unzureichende Leitungsverbindungen können zur Folge haben, dass durch Kurzschluss
• Kabelbrände entstehen,
• der Airbag ausgelöst wird,
• elektronische Steuerungseinrichtungen beschädigt werden,
• elektrische Funktionen ausfallen (Blinker, Bremslicht, Hupe, Zündung, Licht).
A
ACHTUNG!
Klemmen Sie wegen der Kurzschlussgefahr vor Arbeiten an der Fahrzeugelektrik immer
den Minuspol ab.
Bei Fahrzeugen mit Zusatzbatterie müssen Sie an dieser ebenfalls den Minuspol abklem-
men.
Beachten Sie deshalb folgende Hinweise:
• Verwenden Sie bei Arbeiten an den folgenden Leitungen nur isolierte Kabelschuhe, Stecker
und Flachsteckhülsen:
– 30 (Eingang von Batterie Plus direkt)
– 15 (Geschaltetes Plus, hinter Batterie)
– 31 (Rückleitung ab Batterie, Masse)
– L (Blinkerleuchten links)
– R (Blinkerleuchten rechts)
Verwenden Sie keine Lüsterklemmen.
• Verwenden Sie eine Krimpzange zum Verbinden der Kabel.
• Schrauben Sie das Kabel bei Anschlüssen an Leitung 31 (Masse)
– mit Kabelschuh und Zahnscheibe an eine fahrzeugeigene Masseschraube oder
– mit Kabelschuh und Blechschraube an das Karosserieblech.
Achten Sie auf eine gute Masseübertragung!
VT100DIG-IO-16s.book Seite 20 Montag, 1. August 2016 2:46 14
/