Panasonic SCHC58EG Návod na obsluhu

RQT9759-1R

POLSKIČESKY ENGLISHESPAÑOL

Operating Instructions

Instrukcja obsługi

Návod k obsluze

Instrucciones de funcionamiento

Thank you for purchasing this product.

Please read these instructions carefully before using

this product, and save this manual for future use.

Dziękujemy za zakupienie tego produktu.

Przed przystąpieniem do eksploatacji opisywanego

produktu należy dokładnie przeczytać niniejsze

zalecenia i zachować instrukcję obsługi do wglądu.

Děkujeme, že jste si zakoupil tento výrobek.

Před použitím tohoto produktu si pečlivě přečtěte tyto

pokyny a celý návod si uložte pro pozdější použití.

Muchísimas gracias por haber adquirido este aparato.

Lea cuidadosamente estas instrucciones antes de usar

este producto, y guarde este manual para usarlo en el

futuro.

Compact Stereo System

Kompaktowy zestaw stereo

Kompaktní stereo systém

Sistema estéreo compacto

Model No. SC-HC58

Included Installation Instructions

(l 2 and 25, 26)

The installation work should be done by a

qualified installation specialist.

Before commencing work, carefully read these

installation instructions and the operating instructions

to ensure that installation is performed correctly.

(Please keep these instructions. You may need them

when maintaining or moving this unit.)

Załączone instrukcje instalacji

(l 30 i 53, 54)

Instalację powinien przeprowadzić wyłącznie

wykwalifikowany specjalista.

Przed rozpoczęciem pracy należy się dokładnie

zapoznać z instrukcją instalacji oraz z instrukcją

obsługi, aby się upewnić, że instalacja została

przeprowadzona prawidłowo.

(Proszę zachować niniejszą instrukcję. Będzie ona

potrzebna podczas serwisowania lub przenoszenia

urządzenia.)

Přiložené pokyny k instalaci (l 56 a 79, 80)

Instalační práce musí být provedeny

kvalifikovaným instalatérským odborníkem.

Před zahájením instalace si pečlivě pročtěte tyto

pokyny k instalaci a návod k obsluze, abyste instalaci

provedli opravdu správně.

(Tyto pokyny si uschovejte. Můžete je potřebovat při

údržbě nebo přesouvání tohoto zařízení.)

Se incluyen instrucciones de instalación

(l 82 y 105, 106)

La instalación debe ser realizada por un

especialista calificado.

Antes de comenzar la instalación, lea

cuidadosamente estas instrucciones de instalación y

el manual de instrucciones para asegurarse de que la

instalación se realice correctamente.

(Conserve estas instrucciones. Puede necesitarlas al

momento de realizar mantenimiento o trasladar esta

unidad)

EG

RQT9759~Cover_mst.fm 1 ページ２０１３年７月３日　水曜日　午後５時３７分

2

RQT9759

Safety precautions

Unit

≥ To reduce the risk of fire, electric shock or product damage,

– Do not expose this unit to rain, moisture, dripping or

splashing.

– Do not place objects filled with liquids, such as vases, on

this unit.

– Use only the recommended accessories.

– Do not remove covers.

– Do not repair this unit by yourself. Refer servicing to

qualified service personnel.

– Do not let metal objects fall inside this unit.

– Do not place heavy items on this unit.

AC mains lead

≥ To reduce the risk of fire, electric shock or product damage,

– Ensure that the power supply voltage corresponds to the

voltage printed on this unit.

– Insert the mains plug fully into the socket outlet.

– Do not pull, bend, or place heavy items on the lead.

– Do not handle the plug with wet hands.

– Hold onto the mains plug body when disconnecting the

plug.

– Do not use a damaged mains plug or socket outlet.

≥ The mains plug is the disconnecting device.

Install this unit so that the mains plug can be unplugged from

the socket outlet immediately.

Button-type battery (Lithium battery)

≥ Risk of fire, explosion and burns. Do not recharge,

disassemble, heat above 60

o

C or incinerate.

≥ Keep the Button-Type battery out of the reach of children.

Never put Button-Type battery in mouth. If swallowed call

your doctor.

Unit

≥ This unit utilizes a laser. Use of controls or adjustments or

performance of procedures other than those specified herein

may result in hazardous radiation exposure.

≥ Do not place sources of naked flames, such as lighted

candles, on this unit.

≥ This unit may receive radio interference caused by mobile

telephones during use. If such interference occurs, please

increase separation between this unit and the mobile

telephone.

≥ This unit is intended for use in moderate climates.

Placement

≥ Place this unit on an even surface.

≥ To reduce the risk of fire, electric shock or product damage,

– Do not install or place this unit in a bookcase, built-in

cabinet or in another confined space. Ensure this unit is

well ventilated.

– Do not obstruct this unit’s ventilation openings with

newspapers, tablecloths, curtains, and similar items.

– Do not expose this unit to direct sunlight, high

temperatures, high humidity, and excessive vibration.

Button-type battery (Lithium battery)

≥ Danger of explosion if battery is incorrectly replaced.

Replace only with the type recommended by the

manufacturer.

≥ Insert with poles aligned.

≥ Mishandling of batteries can cause electrolyte leakage and

may cause a fire.

– Remove the battery if you do not intend to use the remote

control for a long period of time. Store in a cool, dark

place.

– Do not heat or expose to flame.

– Do not leave the battery(ies) in a car exposed to direct

sunlight for a long period of time with doors and windows

closed.

≥ When disposing the batteries, please contact your local

authorities or dealer and ask for the correct method of

disposal.

NORSK

Produkt

≥ For å redusere faren for brann, elektrisk støt eller skade på

apparatet:

– Utsett ikke produktet for regn, fukt, drypping eller sprut.

– Ikke plasser objekter som er fylt med væske, som vaser,

på apparatet.

– Bruk kun anbefalt tilbehør.

– Fjern ikke deksler.

– Reparer ikke denne enheten selv, overlat service til

kvalifisert servicepersonell.

Vekselstrømnett

≥ Nettstøpselet er trukket ut fra denne enheten.

Installer denne enheten slik at nettstøpselet umiddelbart kan

trekkes fra stikkontakten.

Produkt

≥ Dette produktet anvender en laser. Betjening av kontroller

eller justering eller andre inngrep enn de beskrevet i denne

bruksanvisning kan føre til farlig bestråling.

≥ Plasser ikke åpen ild, slik som levende lys, oppå apparatet.

≥ Dette apparatet er beregnet for bruk under moderate

klimaforhold.

Plassering

≥ For å redusere faren for brann, elektrisk støt eller skade på

apparatet:

– Ikke plasser apparatet i en bokhylle, et innebygget

kabinett eller et annet lukket sted. Pass på at produktet er

godt ventilert.

– Apparatets ventilasjonsåpninger må ikke dekkes til med

aviser, duker, gardiner eller lignende.

WARNING

CAUTION

ADVARSEL

FORSIKTIG

Product Identification Marking is located on the bottom of

the unit.

SC-HC58_EG~RQT9759-R.book 2 ページ２０１３年１月９日　水曜日　午前１０時２５分

3

RQT9759

ENGLISH

Table of contents

Safety precautions............................................ 2

Accessories....................................................... 3

Control reference guide ................................... 4

Connections ...................................................... 5

Unit and media care.......................................... 5

Inserting media ................................................. 6

Network settings............................................... 7

Using AirPlay with this unit’s speakers........ 10

Bluetooth

®

operations .................................... 12

Media playback operations............................ 13

Listening to the radio ..................................... 14

Sound adjustment .......................................... 16

Clock and Timer.............................................. 16

Others .............................................................. 17

Troubleshooting.............................................. 19

About Bluetooth

®

............................................ 22

Playable media................................................ 22

Licenses .......................................................... 23

Specifications.................................................. 24

Attaching the unit to a wall (optional)........... 25

Accessories

About descriptions in these operating instructions

≥ Pages to be referred to are indicated as “l ±±”

Check the supplied accessories before using this unit.

∏ 1 Remote control

(with a battery)

(N2QAYC000081)

∏ 1 AC mains lead

∏ 1 FM indoor

antenna

Wall mounting accessories

∏ 1 Safety holder

∏ 1 Screw

∏ 2 Wall mount

brackets



≥ Do not use AC mains lead with other equipment.

≥ Product numbers provided in these operating instructions are

correct as of January 2013. These may be subject to change.

Information for Users on Collection and Disposal of Old Equipment and used Batteries

These symbols on the products, packaging, and/or accompanying documents mean that

used electrical and electronic products and batteries should not be mixed with general

household waste.

For proper treatment, recovery and recycling of old products and used batteries, please

take them to applicable collection points, in accordance with your national legislation and

the Directives 2002/96/EC and 2006/66/EC.

By disposing of these products and batteries correctly, you will help to save valuable

resources and prevent any potential negative effects on human health and the

environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries, please

contact your local municipality, your waste disposal service or the point of sale where

you purchased the items.

Penalties may be applicable for incorrect disposal of this waste, in accordance with

national legislation.

For business users in the European Union

If you wish to discard electrical and electronic equipment, please contact your dealer or

supplier for further information.

[Information on Disposal in other Countries outside the European Union]

These symbols are only valid in the European Union. If you wish to discard these items,

please contact your local authorities or dealer and ask for the correct method of disposal.

Note for the battery symbol (bottom two symbol examples):

This symbol might be used in combination with a chemical symbol. In this case it

complies with the requirement set by the Directive for the chemical involved.

Cd

SC-HC58_EG~RQT9759-R.book 3 ページ２０１３年１月９日　水曜日　午前１０時２５分

4

RQT9759

Control reference guide

1 Standby/on switch (Í/I) (Í)

Press to switch the unit from on to standby mode or vice

versa.

In standby mode, the unit is still consuming a small

amount of power.

2 Select the audio source

3 Basic playback control buttons

4 Enter setup menu

5 Enter the iPod/iPhone menu

Change displayed information

6 Open or close the sliding door

7 Adjust the volume (0 (min) to 50 (max))

8 Mute the sound

Mutes the sound. Press again to cancel. “MUTE”

is also cancelled when the volume is adjusted or

the unit is turned off.

9 Enter playback menu

10 Enter sound menu

11 Selection/OK

12 “IPOD_PORT” for iPod/iPhone/iPad (l 6)

USB port (l 6)

13 Headphone jack

Plug type: ‰3.5 mm stereo

Recommended plug type: Straight Plug

≥ Listening at full volume for long periods may damage

the user’s ears.

≥ Excessive sound pressure from earphones and

headphones can cause hearing loss.

14 Network setting button (l 7)

15 Power on indicator

16 Wi-Fi

®

status indicator

17 Display

18 Sliding door

19 Remote control signal sensor

Distance: Within approx. 7 m directly in front.

≥ To avoid interference, please do not put any objects in

front of signal sensor.

Unless otherwise indicated, operations are described

using the remote control.

On the remote control:

[iPod/USB]: “IPOD_DOCK” ,. “IPOD_PORT” / “USB”

[CD/RADIO]: “CD” ,. “FM”

[ ]: “BLUETOOTH”

On this unit:

“CD” ----. “FM” ----. “BLUETOOTH” ----. “IPOD_DOCK”

^-------------- “IPOD_PORT” / “USB” (----------------b

SELECTOR

iPad

12

14673216

15

17 18

19

13

16

CD/

RADIO

iPod/

USB

Top view

∫ Before using for the first time

Remove the insulation sheet A.

∫ To replace a button-type battery

Battery type: CR2025 (Lithium battery)

≥ Set the button-type battery with its (i) mark facing upward.

≥ Keep the button-type battery out of reach of children to prevent swallowing.





SC-HC58_EG~RQT9759-R.book 4 ページ２０１３年１月９日　水曜日　午前１０時２５分

5

RQT9759

ENGLISH

Connections



≥ These speakers do not have magnetic shielding. Do not place them near a television, personal computer or other devices easily

influenced by magnetism.

Unit and media care

Pull out the AC mains lead from the outlet before

maintenance.

∫ Clean this unit with a soft, dry cloth

≥ When dirt is heavy, wring a cloth moistened in water tightly to

wipe the dirt, and then wipe it with a dry cloth.

≥ When cleaning the speaker covers, use a fine cloth.

Do not use tissues or other materials (towels, etc.) that can

fall apart. Small grains may get stuck inside the speaker

cover.

≥ Never use alcohol, paint thinner or benzine to clean this unit.

≥ Before using chemically treated cloth, carefully read the

instructions that came with the cloth.

∫ Maintenance of the lens

∫ Clean discs

Wipe with a damp cloth and then wipe dry.

∫ Disc handling precautions

≥ Handle discs by the edges to avoid inadvertent scratches or

fingerprints on the disc.

≥ Do not attach labels or stickers to discs.

≥ Do not use record cleaning sprays, benzine, thinner, static

electricity prevention liquids or any other solvent.

≥ Do not use the following discs:

– Discs with exposed adhesive from removed stickers or

labels (rented discs etc.).

– Discs that are badly warped or cracked.

– Irregularly shaped discs, such as heart shapes.

∫ To dispose or transfer this unit

The unit may keep the user settings information in the

unit. If you discard this unit either by disposal or transfer,

then follow the procedure to return all the settings to the

factory presets to delete the user settings.

(

l

19, “To return all settings to the factory preset”)

≥ The operation history may be recorded in the

memory of this unit.

≥ Tape the antenna to a wall or column in a position with the least amount of interference. (Use an FM outdoor antenna if radio

reception is poor.)

ョヮチモワヵ

ヘブ

モヤチリワ」

1

2

Connect the AC mains lead after all other connections are completed.

This unit consumes a small amount of AC power (l 24) even when turned off.

To household mains socket

AC mains lead (supplied)

≥ In the interest of power conservation, if you will not be using this unit for an extended period of time, unplug it from

the household mains socket.

FM indoor antenna

(supplied)

Adhesive tape

(not supplied)

≥ Clean the lens regularly to prevent malfunctions. Use a

blower to remove dust and a cotton swab if it is extremely

dirty.

≥ You cannot use a CD type lens cleaner.

≥ Do not leave the sliding door open for prolonged periods

of time. This will cause the lens to get dirty.

≥ Be careful not to touch the lens with your fingers.

Lens

DO DO NOT

SC-HC58_EG~RQT9759-R.book 5 ページ２０１３年１月９日　水曜日　午前１０時２５分

6

RQT9759

Inserting media

*1: Refer to “Playable media” for compatible models. (l 22)

*2: When using the “IPOD_PORT” connection, do not connect

the following models to this unit:

– iPod classic, iPod [4th (colour display), and 5th (video)

generation]

Unexpected behaviour may occur.

*3: Connect using the dedicated USB cable (not supplied).

*4: Insert the USB device directly. Do not use any USB

extension cable.

*5: When using the “IPOD_DOCK” connection:

≥ Be sure to remove the iPod/iPhone from its case.

≥ Do not push or pull the dock manually.

≥ Make sure that the iPod/iPhone is fully inserted and its

back is resting against the cushion pad.

≥ Make sure to hold the dock when removing the iPod/

iPhone.

*6: Make sure to tilt the disc so as not to touch the sliding door.

≥ Do not open the sliding door manually.

≥ Make sure that the unit does not fall when inserting or

removing media.

≥ When moving this unit, be sure to remove all media and turn

this unit to standby mode.

≥ Before removing the USB device, select a source other than

“USB”.

Charging starts when an iPod*

2

/iPhone/iPad is

connected to this unit.

≥ During standby mode, charging will not start from the

“IPOD_PORT” connection, however it will start as usual from

the “IPOD_DOCK” connection.

– To charge from the “IPOD_PORT” connection, start the

charging before turning this unit to standby mode.



≥ Check the iPod/iPhone/iPad to see if the battery is fully

charged. (Once fully recharged, additional recharging will not

occur.)

≥ If this unit is switched to standby mode

“IPOD CHARGING” is shown on the unit’s display.

iPad

Select “IPOD_DOCK” as the source

Connect using the Lightning connector *1

Select “IPOD_PORT” as the source

“USB” is displayed when a compatible USB is

inserted.

Select “CD” as the source

*1, 2, 3

*4

*5

*6

Charging an iPod/iPhone/iPad

SC-HC58_EG~RQT9759-R.book 6 ページ２０１３年１月９日　水曜日　午前１０時２５分

7

RQT9759

ENGLISH

Network settings

With this feature you can wirelessly stream music from

an iOS device (iPhone, iPod, iPad) or a Mac/PC to this

unit’s speakers.

To use this feature (AirPlay), this unit must join the

same 2.4 GHz wireless network as the AirPlay

compatible device (l 22).

≥ It is also possible to use AirPlay without a wireless network

router. (l 11, “Directly streaming to this unit”)

Preparation

≥ Place this unit close to the wireless network router.

1 Turn this unit on.

2 Follow the chart below to choose the network

setting method.



≥ To cancel this setting in the middle, press [Í] to turn off the

unit.

*1: Depending on the network environment or the wireless

network router settings, it may take more than 10 mins. to

complete the settings.

With this method you will share the wireless network

settings of your iPod touch/iPhone/iPad with this unit.

≥ The following explanations are based on an iPhone.

1 Connect the iPhone to your home wireless

network.

2 Connect the iPhone to this unit.

Choose one of the following connections.

– “IPOD_DOCK” connection compatible iPod touch/

iPhone

– iPod touch/iPhone/iPad with iOS 5.0 or later

3 Unlock your iPhone and then press and hold

[– NETWORK SETUP] on this unit for more than

3 seconds.

≥ If “NOT SUPPORTED” or “SET WI-FI” is displayed,

check that the iPhone is connected to the wireless

network and try again from step 1.

4 A message will pop-up on your iPhone.

Allow the iPhone to share the wireless network

settings.*

1

{. The Wi-Fi status indicator blinks.

5 The unit’s settings are completed when

“SUCCESS” is displayed and the Wi-Fi status

indicator stops blinking and lights in blue.

6 Press [OK] on the remote control to exit the

settings.

7 To use AirPlay, turn to page 10.

Does your wireless network router

support WPS?

Yes

Are you using an

iPod touch/iPhone/iPad?

Is the iOS version 5.0 or later?

l right,

“Method 1”

l 8,

“Method 2”

l 8,

“Method 3”

No

Yes No / Do not know

Method 1

If you're using an iPod touch/iPhone/iPad.

(iOS version 5.0 or later.)

If “FAIL” is displayed press [OK] and try the setting

again. If “FAIL” is still displayed, try “Method 2” or

“Method 3”.

≥ If the iPhone was disconnected midway through, try again

without disconnecting it.

iPad

SC-HC58_EG~RQT9759-R.book 7 ページ２０１３年１月９日　水曜日　午前１０時２５分

8

RQT9759

∫ Using the WPS Push Button

Configuration (PBC)

1 Disconnect any devices connected to this unit.

2 Press and hold [– NETWORK SETUP] on the unit.

≥ Complete step 3 within 2 mins.

3 After “WPS” is indicated, press the WPS button on

the wireless network router.

4 The unit’s settings are completed when

“SUCCESS” is displayed and the Wi-Fi status

indicator stops blinking and lights in blue.

5 Press [OK] on the remote control to exit the

setting.

6 To use AirPlay, turn to page 10.



≥ To use the WPS PIN code, refer to the notes on page 9.

With this method, you will access this unit’s wireless

network settings from the Internet browser of your

compatible device.

≥ The following explanations are based on an iPhone.

1 Press [SETUP] on the remote control repeatedly

to select “NET SETUP” and then press [OK].

2 After “SETTING” is indicated, connect your

iPhone to this unit’s wireless network called

“00 Setup _ _ _ _ _ _”*

1, 2

.

3 Start “Safari” on your iPhone and type

“http://192.168.1.12/” into the URL address field

and display the page.

{. This unit’s setup window is displayed.

Method 2

If your wireless network router supports WPS

(Wi-Fi Protected Setup

TM

).

The WPS identifier mark

WPS Push Button Configuration

(PBC) compatible wireless network

router may have this mark.

“FAIL” may be displayed if the connection was not

made within the set time limit. Try the setting again.

If “FAIL” is still displayed, try “Method 3”.

Blinks blue

Method 3

Setting the network connection from an Internet

browser.

Blinks purple

SC-HC58_EG~RQT9759-R.book 8 ページ２０１３年１月９日　水曜日　午前１０時２５分

9

RQT9759

ENGLISH

4 Select “Search wireless network”.

5 Select and input the details.

≥ Check your home wireless network name

(Network name (SSID)) and password for this

network. This can often be found on the wireless

network router itself.

6 Select “JOIN” to apply the settings.

≥ In the pop-up screen, select “OK” to continue.

– Select “Cancel” to return to the setup window.

7 The unit’s settings are completed when

“SUCCESS” is displayed and the Wi-Fi status

indicator stops blinking and lights in blue.

8 Make sure to connect your iPhone back to your

home wireless network*

4

.

9 To use AirPlay, turn to page 10.

*1: “ _ ” stands for a digit that is unique to each set.

*2: Make sure that DHCP is enabled for the network setting on

the iPhone.

*3: If you have set your wireless network to be invisible, select

“BACK” and refer to “Alternative settings”.

*4: To use the AirPlay function, connect the iPhone to the

wireless network selected in step 5. (l above)

≥ The below settings are the alternative or additional settings

for “Method 3”. (l 8)



≥ Enable Java and Cookies in your browser settings.

≥ This unit can also be set using the WPS PIN code.

Replace step 3 of “Method 2” with the following steps.

(Before starting, refer to the wireless network router’s

operating instructions for details on how to enter the PIN

code.)

1 While “WPS” is flashing press and hold

[– NETWORK SETUP] again to display the 8 digit PIN

code.

{. Wi-Fi status indicator blinks purple.

2 Enter the PIN code into the wireless network router.

[1] Select your home wireless network

name.*

3

[2] Type the password.

If “FAIL” is displayed press [OK], check the wireless

network password and other settings and start again

from step 1.

Advanced network settings

Alternative settings

Instead of steps 4 and 5

Select “Manual settings”.

1 Type your home wireless network name into

the “Network name (SSID)” field.

2 Select the encryption method from the

“Security system” drop down list.

3 Type the password into the “Password” field

and then select “JOIN”.

Additional settings

If your home wireless network has been configured

to use specific IP Addresses, Subnet Mask, Default

Gateway, Primary DNS, etc.

Before step 6

Select “Advanced network settings”.

{. Input the required addresses into each field and select

“JOIN”.

≥ To change the settings back to DHCP, select “ON” from the

“DHCP” drop down list.

If you want to change the name of this unit that is

displayed as the AirPlay speakers.

Before step 4

Select “Additional settings”.

1 Select “Edit STEREO SYSTEM name”.

2 Type a new name into the

“STEREO SYSTEM name” field.

{. Only ASCII characters can be used.

3 Select “OK”.

4 If this unit is already connected to your home

wireless network:

–Select “Additional settings”, and then select

“Exit”.

If this unit is not connected to your home

wireless network:

– Continue to step 4 of “Method 3”.

SC-HC58_EG~RQT9759-R.book 9 ページ２０１３年１月９日　水曜日　午前１０時２５分

10

RQT9759

Using AirPlay with this

unit’s speakers

1 Turn the unit on.

≥ Check that the Wi-Fi status indicator lights in

blue.

≥ If it doesn’t light in blue, check the wireless

network settings. (l 7)

2 iOS device:

Start the “Music” (or iPod) app.

Mac/PC:

Start “iTunes”.

≥ If the Music app on your iOS device is used, select the

audio file you want to play.

3 Select “Panasonic HC58 _ _ _ _ _ _”*

1, 2

from the

AirPlay icon.

{. Check the volume settings before starting the playback.

(When AirPlay is used for the first time, the volume may

be output at the maximum setting.)

4 Start play.

≥ The playback will start with a slight delay.



≥ This unit can be set to turn on automatically when this unit is

selected as the output speakers. (l 18)

≥ Playback of other audio sources will stop and AirPlay output

will have priority.

≥ Volume changes on the iOS device or iTunes will be applied

to this unit. (Refer to the iTunes Help for the required settings

in iTunes.)

≥ With some iOS and iTunes versions, it may not be possible

to restart the AirPlay playback if the selector is changed

(e.g., “CD”) or the unit is turned off, during the AirPlay

playback.

In this case, select a different device from the AirPlay icon of

the Music App or iTunes and then re-select this unit as the

output speakers.

≥ AirPlay will not work when playing back videos on iTunes.

*1: “ _ ” stands for a digit that is unique to each set.

*2: The name that is displayed for this unit can be changed

from the “Edit STEREO SYSTEM name” settings.

(l 9, “Advanced network settings”)

Preparation

≥ Complete the network settings. (l 7)

≥ Connect the iOS device or Mac/PC to the same

home wireless network as this unit.

Lights in blue

e.g.,

iPhone iOS 6.0.1

e.g.,

iTunes 11.0

SC-HC58_EG~RQT9759-R.book 10 ページ２０１３年１月９日　水曜日　午前１０時２５分

11

RQT9759

ENGLISH

With this function set to “ON”, you can stream music

from the iOS device or Mac / PC (iTunes 10.2.2 or

later) to this unit without the need of a wireless network

router.

≥ Previous network settings will be deleted when this

function is set to “ON”.

≥ The following explanations are based on an iPhone.

1 Press [SETUP] repeatedly to select

“D.CONNECT”.

2 Press [3, 4] to select “ON” and then press [OK].

3 Press [3, 4] to select “OK? YES” and then press

[OK].

4 Connect your iPhone to this unit’s wireless

network named “HC58 _ _ _ _ _ _”*

2

.

5 Enter the password that is indicated on this unit’s

display.

6 Once the iPhone is connected to this unit’s

wireless network, the setup is completed.

7 Continue to step 2 of “Using AirPlay with this unit’s

speakers” (l 10).



≥ This setting is reset to “OFF” when other network settings are

performed. (l 7)

≥ When “D.CONNECT” is set to “ON”, this unit will not be

connected to the Internet. It is not possible to update the

software or check the Wi-Fi signal strength.

≥ When AirPlay is not being used, disconnect the AirPlay

compatible device from this network.

≥ When using a computer on this network, make sure that all

the shared files are encrypted.

≥ This feature is only compatible with the “Open System”

authentication method. It is not compatible with “Shared Key”

authentication method.

The first time “D.CONNECT” is set to “ON”, a

password for this unit’s wireless network is randomly

created and memorised in this unit.

≥ This password is memorised until it is changed.

1 While “D.CONNECT” is set to “ON”:

Press [SETUP] repeatedly to select

“D.CONNECT”.

2 Press [3, 4] to select “ON” and then press [OK].

3 The current password is displayed.

≥ The 5 digits after “PW” is the password for this

network.

4 Press any button to exit.

1 While “D.CONNECT” is set to “OFF”:

Press [SETUP] repeatedly to select

“D.CONNECT”.

2 Press [3, 4] to select “CHANGE PW” and then

press [OK].

3 Press [3, 4] to select “OK? YES” and then press

[OK].

4 The new password is displayed.

≥ The 5 digits after “PW” is the new password for

this network.

5 Press any button to exit.

∫ Note about changing the password

After changing this unit’s wireless network password, if

you are not prompted to change the password on the

other devices, the following changes are required.

iOS device (iPod touch/iPhone/iPad)*

3

:

≥ Before choosing this unit’s network,

1 Select [ ] located beside this unit’s wireless

network name.

2 Select “Forget this Network” and then select

“Forget”.

3 Select this unit’s wireless network and enter the

new password.

Mac/PC:

≥ If the computer has memorised the old password, be

sure to change the memorised password for this

unit’s wireless network to the new one.



≥ Refer to the devices’s operating instructions for details.

*1: “ _ ” stands for a digit.

*2: “ _ ” stands for a digit that is unique to each set.

*3: Steps are based on iOS 6.0.1.

Directly streaming to this unit

“PW _ _ _ _ _ ”*

1

is displayed.

The 5 digits after “PW” is the password for this

network.

Display the password

Change the password

SC-HC58_EG~RQT9759-R.book 11 ページ２０１３年１月９日　水曜日　午前１０時２５分

12

RQT9759

Bluetooth

®

operations

By using the Bluetooth

®

connection, you can listen to

the sound from the Bluetooth

®

audio device from this

unit wirelessly.

Preparation

≥ Turn on the Bluetooth

®

feature of the device and

place the device near this unit.

≥ If this unit is already connected to a Bluetooth

®

device, disconnect it.

1 Press [ ] to select “BLUETOOTH”.

≥ If “PAIRING” is indicated on the display, go to

step 3.

2 Press [PLAY MENU] to select “NEW DEV.” and

then press [OK].

{. “PAIRING” is indicated on the display.

3 Select “SC-HC58” from the Bluetooth

®

device’s

Bluetooth

®

menu.

4 Start play on the Bluetooth

®

device.



≥ Refer to the operating instructions of the Bluetooth

®

device

for details.

If prompted for the passkey, input “0000”.

≥ You can register up to 8 devices with this unit. If a 9th device

is paired, the device that has not been used for the longest

time will be replaced.

Preparation

≥ Turn on the Bluetooth

®

feature of the device and

place the device near this unit.

≥ If this unit is already connected to a Bluetooth

®

device, disconnect it.

1 Press [ ] to select “BLUETOOTH”.

{. “READY” is indicated on the display.

2 Select “SC-HC58” from the Bluetooth

®

device’s

Bluetooth

®

menu.

{. The name of the connected device is indicated on the

display for 2 seconds.

3 Start play on the Bluetooth

®

device.



≥ This unit can only be connected to one device at a time.

≥ When “BLUETOOTH” is selected as the source, this unit will

automatically try and connect to the last connected

Bluetooth

®

device. The Bluetooth

®

device will be

disconnected if a different audio source (e.g., [CD]) is

selected.

You can change the transmission speed to prioritize

transmission quality or sound quality.

Preparation

≥ Press [ ] to select “BLUETOOTH”.

≥ If a Bluetooth

®

device is already connected,

disconnect it.

1 Press [PLAY MENU] repeatedly to select

“LINK MODE”.

2 Press [3, 4] to select the mode and then press

[OK].

MODE 1: Emphasis on connectivity

MODE 2: Emphasis on sound quality



≥ The default setting is “MODE 1”.

If the sound input level of the Bluetooth

®

transmission

is too low, change the input level setting.

Preparation

≥ Connect a Bluetooth

®

device.

1 Press [PLAY MENU] repeatedly to select “INPUT

LEVEL”.

2 Press [3, 4] to select the level and then press

[OK].

“LEVEL 0” ,. “LEVEL i1” ,. “LEVEL i2”

^---------------------------------------------------------J



≥ Select “LEVEL 0” if the sound is distorted.

≥ The default setting is “LEVEL 0”.

1 While a Bluetooth

®

device is connected:

Press [PLAY MENU] to select “DISCONNECT?”.

2 Press [3, 4] to select “OK? YES” and then press

[OK].

Pairing Bluetooth

®

devices

Connecting a paired Bluetooth

®

device

Bluetooth

®

transmission mode

Bluetooth

®

input level

Disconnecting a Bluetooth

®

device

SC-HC58_EG~RQT9759-R.book 12 ページ２０１３年１月９日　水曜日　午前１０時２５分

13

RQT9759

ENGLISH

Media playback operations

The following marks indicate the availability of the

feature.

Preparation

≥ Turn the unit on.

≥ Insert the media (l 6) or connect the Bluetooth

®

(l 12) / AirPlay (l 10) compatible device.

≥ Press [CD], [iPod/USB] or [ ] to select the audio

source.



≥ When using iPod/iPhone/iPad, the operation may vary

among those models.

∫ [CD], [USB], [Bluetooth] To display

information

Press [DISPLAY] repeatedly.



≥ To use this unit’s remote control with a Bluetooth

®

device, the

Bluetooth

®

device must support AVRCP (Audio Video

Remote Control Profile).

Depending on the device or the status of the device, some

operations may not work.

≥ Maximum number of displayable characters: approx. 30

≥

This unit supports ver. 1.0, 1.1 and 2.3 ID3 tags. Text data that

is not supported will not be displayed or shown differently.

≥ Album and track indication for MP3 files.

∫ [iPod] To navigate through the iPod/

iPhone menu

Open the Music App to use this feature with

iPod touch/iPhone.

–[3, 4]: To navigate menu items.

– [OK]: To go to the next menu.

– [iPod MENU]: To return to the previous menu.



≥ To view the operation, open the sliding door.

≥ Depending on the model (e.g., iPod nano 7th generation,

etc.), it may be necessary to select the album, artist, etc. on

the iPod/iPhone.

[CD]: CD audio in CD-DA format and a CD that

contains MP3 files (l 23)

[iPod]: Compatible iPod/iPhone/iPad (l 22)

[USB]: USB devices containing MP3 files (l 23)

[AirPlay]: When connected to an AirPlay compatible

device. (l 10)

[Bluetooth]: Connected Bluetooth

®

device (l 12)

Basic play

([CD], [iPod], [USB], [AirPlay], [Bluetooth])

Play Press [1/;].

Stop Press [∫].

≥ [USB]: The position is memorised

and “RESUME” is displayed.

Pause Press [1/;].

Press again to restart play.

Skip Press [:/6] or [5/9]

to skip track.

[CD], [USB] Press [3] or [4] to

skip the MP3 album.

Search

(Except [AirPlay])

During play or pause

Press and hold [:/6] or

[5/9].

≥ [iPod]: Backwards search is only

within the current track.

“A _ _ _”: MP3 album number.

“T _ _ _”: MP3 track number.

≥ “ _ ” stands for the album or track number.

“”:

This indication is also used to refer to an album.

“”:

This indication is also used to refer to a track.

SC-HC58_EG~RQT9759-R.book 13 ページ２０１３年１月９日　水曜日　午前１０時２５分

14

RQT9759

Select the playback mode.

1 Press [PLAY MENU] to select “REPEAT”,

“RANDOM” / “SHUFFLE” or “PLAYMODE”.

2 Press [3, 4] to select the setting and then press

[OK].



≥ When using an iPod/iPhone/iPad or Bluetooth

®

device, use

the setting on the device, if available.

≥ During random/shuffle play, you cannot skip to the previous

track.

≥ [CD]: The mode is cancelled when you open the sliding door

for discs.

[AirPlay]: The applied settings will remain until it is changed.

*1: [AirPlay]: Perform the settings during playback.

Preparation

≥ Turn the unit on.



≥ A station previously stored is overwritten when another

station is stored in the same channel preset.

1 Press [PLAY MENU] to select “A.PRESET”.

2 Press [3, 4] to select “LOWEST” or “CURRENT”

and then press [OK].

LOWEST:

CURRENT:

To begin auto preset with the current frequency.*

* To change the frequency, refer to “Manual tuning and

presetting”.

The tuner starts to preset all the stations it can

receive into the channels in ascending order.

Preparation

1 Press [PLAY MENU] repeatedly to select

“TUNEMODE”.

2 Press [3, 4] to select “PRESET” and then press

[OK].

Press [:/6] or [5/9] to select the channel.

Playback modes ([CD], [USB], [AirPlay]*

1

)

REPEAT

[CD] [USB]

OFF Select to cancel repeat playback.

1-TRACK Only plays the selected track.

≥ “1”, “ ”, “`” is displayed.

(Skip to the desired track.)

ALL All tracks are repeated.

≥ “`” is displayed.

[AirPlay]

Refer to the connected device to verify the

selected setting.

[CD] [USB] RANDOM

ON Plays the contents randomly.

≥ “RND” is displayed.

≥ “RND” will not be displayed when

“1-TRACK” is selected.

OFF Random playback is turned off.

[AirPlay] SHUFFLE

Refer to the connected device to verify the selected

setting.

[CD] (MP3) [USB] PLAYMODE

ALL Play all MP3 tracks.

1-ALBUM Only plays the selected MP3 album.

≥ “1”, “ ” is displayed.

Listening to the radio

You can preset up to 30 channels.

≥ Make sure that the antenna is connected. (l 5)

≥ Press [RADIO] to select “FM”.

Presetting stations automatically

To begin auto preset with the lowest frequency

(FM 87.50).

Listening to a preset channel

SC-HC58_EG~RQT9759-R.book 14 ページ２０１３年１月９日　水曜日　午前１０時２５分

15

RQT9759

ENGLISH

∫ Manual tuning and presetting

Select a radio broadcast.

1 Press [PLAY MENU] repeatedly to select

“TUNEMODE”.

2 Press [3, 4] to select “MANUAL” and then press

[OK].

3 Press [:/6] or [5/9] to tune to the

required station.

≥ To start automatic tuning, press and hold [:/6],

[5/9] until the frequency starts scrolling. Tuning

stops when a station is found.

To preset the channel

4 While listening to the radio broadcast

Press [OK].

5 Press [3, 4] to select the channel and then press

[OK].

∫ To improve FM sound quality

1 While receiving FM broadcasts, press

[PLAY MENU] repeatedly to select “FM MODE”.

2 Press [3, 4] to select “MONO” and then press

[OK].

≥ This setting can be preset and memorised. To do so,

continue to step 4 of “Manual tuning and presetting”.



≥ Select “STEREO” in step 2 to return to stereo broadcasts.

≥ “MONO” is cancelled if the frequency is changed.

Press [DISPLAY] to display the text data.

≥ Each time you press the button:



≥ “STEREO” is displayed when this unit tunes to a stereo

broadcast.

≥ The unit can display the text data transmitted by the radio

data system (RDS) available in some areas. (RDS displays

may not be available if reception is poor.)

≥ If “MONO” is selected, regardless of the type of signal this

unit is receiving, “FM MONO” is displayed. (l below)

∫ To display the current signal status

Press [PLAY MENU] to display “FM STATUS” and then

press [OK].

“FM ST”: The FM signal is in stereo.

“FM”: The FM signal is in monaural.

≥ “FM” is also displayed even if this unit is not tuned to a

station.

∫ To display RDS text data

“PS”: Programme service

“PTY”: Programme type

“FREQ”: Frequency display

SC-HC58_EG~RQT9759-R.book 15 ページ２０１３年１月９日　水曜日　午前１０時２５分

16

RQT9759

Sound adjustment

The following sound effects can be added to the audio

output.

1 Press [SOUND] repeatedly to select the effect.

2 Press [3, 4] to select the setting and then press

[OK].

≥ You may experience a reduction in sound quality when these

effects are used with some sources. If this occurs, turn the

sound effects off.

Clock and Timer

This is a 24-hour clock.

1 Press [SETUP] repeatedly to select “CLOCK”.

2 Press [3, 4] to set the time and then press [OK].



≥ To display the clock, press [SETUP] to select “CLOCK” and

then press [OK] once. The time is displayed for 10 seconds.

(During standby, press [DISPLAY] once.)

≥ The clock is reset when there is a power failure or when the

AC mains lead is removed.

≥ Reset the clock regularly to maintain accuracy.

You can set the timer so this unit turns on at a certain

time every day.

Preparation

Set the clock (l left).

∫ Setting the timer

1 Press [SETUP] repeatedly to select “TIMER ADJ”.

2 Press [3, 4] to set the starting time

(“ON TIME”) and then press [OK].

3 Press [3, 4] to set the finishing time

(“OFF TIME”) and then press [OK].

∫ Turn the timer on

1 Select the music source*

1

and set the desired

volume.

2 Press [SETUP] repeatedly to select “TIMER SET”.

3 Press [3, 4] to select “SET” and then press [OK].

≥ “F” is displayed.

≥ To turn the timer off, select “OFF”.

4 Press [Í] to turn the unit off.



≥ To display the timer settings, press [SETUP] repeatedly to

select “TIMER ADJ” and then press [OK] once.

The music source and volume will also be displayed if the

timer is turned on.

≥ During standby, if the timer is turned on, press [DISPLAY]

twice to display the settings.

≥ This unit can be used as normal after the timer is set,

however:

– Turn the unit to standby mode before the timer start time.

– Even if the audio source or the volume is changed, the

timer will still use the audio source and volume that was

set when the timer was turned on.

The sleep timer can turn the unit off after a set time.

1 Press [SETUP] to select “SLEEP”.

2 Press [3, 4] to set the time (in minutes) and then

press [OK].

“SLEEP 30” ,. “SLEEP 60” ,. “SLEEP 90” ,. “SLEEP 120”

^------------------------. OFF (Cancel) (------------------------J

≥ The remaining time is indicated on the unit’s display

except when other operations are performed.

≥ The play timer and sleep timer can be used together.

The sleep timer always has priority.

Direct-Vocal

Surround

(D.SURROUND)

“LEVEL 1”, “LEVEL 2” or “OFF”.

≥ The factory preset is “OFF”.

Preset EQ

(PRESET EQ)

“HEAVY” (heavy), “SOFT” (soft),

“CLEAR” (clear), “VOCAL”

(vocal) or “FLAT” (flat/off).

≥ The factory preset is “HEAVY”.

Bass (BASS) or

Treble (TREBLE)

Adjust the level (j4 to i4).

Dynamic Bass

(D.BASS)

“ON D.BASS” or “OFF D.BASS”.

≥ The factory preset is “ON D.BASS”.

Setting the clock

Play timer

*1: “CD”, “USB”, “IPOD_PORT”, “IPOD_DOCK” and “FM” can

be set as the music source.

Sleep timer

SC-HC58_EG~RQT9759-R.book 16 ページ２０１３年１月９日　水曜日　午前１０時２５分

17

RQT9759

ENGLISH

Others

As a factory preset, this unit will always turn off

automatically if there is no sound output and no

operation for approx. 30 minutes.

To cancel this function

1 Press [SETUP] repeatedly to select “AUTO OFF”.

2 Press [3, 4] to select “OFF” and then press [OK].



≥ To turn automatic standby on, select “ON” in step 2.

The brightness of this unit’s display can be changed.

1 Press [SETUP] repeatedly to select “DIMMER”.

2 Press [3, 4] to select “ON” and then press [OK].



≥ To cancel the dimmer, select “OFF” in step 2.

When other Panasonic equipment responds to the

supplied remote control, change the remote control

code.

1 Press [CD] to select “CD”.

2 While pressing and holding [SELECTOR] on the

unit, press and hold [CD/RADIO] on the remote

control until the unit's display shows “REMOTE 2”.

3 Press and hold [OK] and [CD/RADIO] on the

remote control for at least 4 seconds.



≥ To change the mode back to “REMOTE 1”, repeat the steps

above but replace the button pressed on the remote control

from [CD/RADIO] to [ ].

Occasionally, Panasonic may release updated

software for this unit that may add or improve the way

a feature operates. These updates are available free of

charge.

Preparation

≥ Turn the unit on.

≥ Connect this unit to the wireless network. (l 7)

– Make sure that the wireless network is connected

to the Internet.

– If “D.CONNECT” is set to “ON”, change the setting

to “OFF” and connect this unit to a wireless

network that is connected to the Internet.

1 Press [SETUP] repeatedly to select

“SW UPDATE” and then press [OK].

2 Press [3, 4] to select “UPDATE? Y” and then

press [OK] to start the update.

3 When the update has finished successfully,

“SUCCESS” is displayed.

4 Disconnect the AC mains lead and reconnect it

after 3 minutes.

≥ Downloading will require several minutes. It may take

longer or may not work properly depending on the

connection environment.



≥ If you do not want to update the unit, select “UPDATE? N”

and then press [OK] in step 2.

≥ If there are no updates, “NO NEED” is displayed after step 2.

∫ Checking the software version

1 Press [SETUP] repeatedly to select “SW VER.” and then

press [OK].

{. The version of the installed software is displayed.

2 Press [OK] to exit.

Automatic standby

≥ This setting cannot be selected when “FM” is the source.

Display brightness

Changing the unit and remote

control code

Software update

DO NOT DISCONNECT the AC mains lead while

one of the following messages is displayed.

– “LINKING”, “UPDATING” or “%”

(“  ” stands for a number.)

≥ During the update process, no other operations can be

performed.

SC-HC58_EG~RQT9759-R.book 17 ページ２０１３年１月９日　水曜日　午前１０時２５分

18

RQT9759

To check the Wi-Fi signal strength where the unit is

located.

Preparation

Connect this unit to the wireless network. (l 7)

1 Press [SETUP] repeatedly to select “SIG.LEVEL”

and then press [OK].

≥ The unit’s display shows “LEVEL ”.

(“  ” stands for a number.)

2 Press [OK] to exit this display mode.



≥ It is recommended to have a signal strength of “3”. Change

the position or angle of your wireless network router or the

unit if the indication is “2” or “1” and see if the connection

improves.

≥ If “LEVEL 0” is displayed, this unit cannot establish a link with

the wireless network router. (l 21)

≥ This function does not work when “D.CONNECT” is set to

“ON”.

This unit can turn on automatically from standby mode

when this unit is selected as the AirPlay speakers.

Preparation

Connect this unit to the wireless network. (l 7)

1 Press [SETUP] repeatedly to select “NET STNBY”

and then press [OK].

2 Press [3, 4] to select “ON” and then press [OK].



≥ To cancel this function, select “OFF” in step 2.

≥ The factory preset is “OFF”. If this function is set to “ON” the

standby power consumption will increase.

Display the name for the connected wireless network

(SSID).

1 Press and hold [– NETWORK SETUP] on the unit

and [OK] on the remote control until the unit's

display shows the SSID.

2 Press [OK] to exit.



≥ If “NOCONNECT” is displayed this unit is not connected to a

wireless network.

≥ All letters are displayed as capital letters, and characters that

cannot be displayed are replaced with “¢”.

To check the unit’s IP address or the Wi-Fi MAC

address.

1 Press and hold [– NETWORK SETUP] on the unit

and [4] on the remote control until the unit’s

display shows the IP address.

{. The IP address is partially displayed.

≥ To display the MAC address on the unit, repeat the

steps above by replacing [4] with [3].

2 Press [3, 4] on the remote control to show the

rest of the IP address.



≥ To exit the setting, wait 20 sec.

≥ The “ – ” displayed on the top or bottom left of the display

indicate the first and last units respectively.

Wi-Fi signal strength

Network standby

Wireless network name (SSID)

IP/MAC Address

SC-HC58_EG~RQT9759-R.book 18 ページ２０１３年１月９日　水曜日　午前１０時２５分

19

RQT9759

ENGLISH

Troubleshooting

Before requesting service, make the following checks.

If you are in doubt about some of the check points, or if

the solutions indicated in the following guide do not

solve the problem, consult your dealer for instructions.

Do you have the latest software installed?

≥ Occasionally, Panasonic may release updated software for this

unit that may add or improve the way a feature operates. (l 17)

Humming heard during play.

≥ An AC mains lead or fluorescent light is near the cords. Keep

other appliances and cords away from this unit’s cables.

MP3 cannot be read.

≥ You may not be able to play MP3 if you have copied a

multi-session disc that has no data between sessions.

≥ When creating a multi-session disc, it is necessary to close the

session.

≥ The amount of data on the disc is too small. Set the amount of

data to above 5 MB.

Incorrect display or play will not start.

≥ Make sure that the disc is compatible with this unit. (l 23)

≥ There is moisture on the lens. Wait for about an hour and then try

again.

No response when [1/;] is pressed.

≥ Disconnect the USB device and then reconnect it. Alternatively,

turn the unit off and on again.

The USB drive or its contents cannot be read.

≥ The USB drive format or its contents is/are not compatible with the

unit (l 23).

≥ The USB host function of this product may not work with some

USB devices.

Slow operation of the USB flash drive.

≥ Large file size or high memory USB flash drive takes longer time

to read.

The elapsed time displayed is different from the

actual play time.

≥ Copy the data to another USB device or backup the data and

reformat the USB device.

A beat sound or noise is heard while receiving

radio broadcast.

≥ Adjust the position of the antenna.

≥ Try to keep a certain amount of distance between the antenna and

AC mains lead.

≥ Try using an outdoor antenna if there are buildings or mountains

nearby.

≥ Switch the television or other audio players off or separate it from

this unit.

≥ Keep this unit away from mobile phones if the interference is

apparent.

Cannot charge or operate.

≥ Have you selected the appropriate selector?

Press [iPod] to select either “IPOD_DOCK” or “IPOD_PORT”.

≥ Check that the iPod/iPhone/iPad is connected properly. (l 6)

≥ The battery of the iPod/iPhone/iPad is depleted. Charge the iPod/

iPhone/iPad, and then operate again.

≥ Connect the iPod/iPhone/iPad again or try to restart the iPod/

iPhone/iPad.

≥ When this unit is in standby mode, charging will not start when

using the “IPOD_PORT” connection.

Turn this unit on and make sure the charging has started before

switching this unit to standby mode.

To return all settings to the factory preset

When the following situations occur, reset the

memory:

≥ There is no response when buttons are pressed.

≥ You want to clear and reset the memory contents.

1 Disconnect the AC mains lead. (Wait for at least

3 minutes before proceeding to step 2.)

2 While pressing and holding down [Í/I] on the

unit, reconnect the AC mains lead.

≥ “--------” appears on the display.

3 Release [Í/I].



≥ All the settings are returned to the factory preset. You will

need to reset the memory items.

Common problems

Disc operations

USB operations

Radio

≥ Confirm the antenna is properly connected. (l 5)

iPod/iPhone/iPad operations

SC-HC58_EG~RQT9759-R.book 19 ページ２０１３年１月９日　水曜日　午前１０時２５分

20

RQT9759

Cannot connect to the network.

≥ Confirm the network connection and settings. (l 7)

≥ Your wireless network might be set to be invisible. In this case

select “Manual settings” in “Method 3”. (l 9)

≥ This unit cannot join a wireless network using WEP security

settings with the WPS methods (“Method 2”). Use “Method 3” to

join the wireless network. (l 8)

≥ Make sure that the multicast function on the wireless network

router is set to on (enabled).

≥ When “D.CONNECT” is used, if the password for “D.CONNECT”

has been changed connect the other device to this unit using the

new password. (l 11)

Cannot connect to the unit.

≥ Display the wireless network name that this unit is connected to

and make sure that the device is connected to the same network.

(l 7)

≥ If “NET STNBY” is set to “OFF”, the AirPlay compatible device

cannot be connected when this unit is off.

≥ Turn off the Wi-Fi setting on the AirPlay compatible device, set

“NET STNBY” to “OFF” (l 18) and then turn this unit off and on.

Reconnect the compatible device to the Wi-Fi network and then

select this unit as the AirPlay speakers again.

My wireless network router is WPS PBC

compatible, but the pairing does not work.

≥ If the network is set to be invisible, the push button configuration

does not work. In this case, either make the wireless network

visible while you set up the network for this unit or use “Method 1”

or “Method 3”. (l 7, 8)

Playback does not start.

The sound is interrupted.

≥ Simultaneous use with other 2.4 GHz devices, such as

microwaves, cordless telephones, etc., may result in connection

interruptions.

Increase the distance between this unit and these devices.

≥ Do not place this unit inside a metal cabinet, for it might block the

Wi-Fi signal.

≥ Place this unit closer to the wireless network router.

≥ If “D.CONNECT” is set to “ON”, place the AirPlay compatible

device closer to this unit.

≥ If several wireless devices are simultaneously using the same

wireless network as this unit, try turning off the other devices or

reducing their wireless network usage.

≥ If the playback stops, check the playback status on the iOS device

or iTunes.

≥ If play does not start (even though the Wi-Fi status indicator lights

in blue and the AirPlay icon is displayed), restart the wireless

network router, turn the Wi-Fi connection on the iOS device or

Mac/PC off and on, and then make sure that your home wireless

network is selected.

≥ If the AirPlay icon is not displayed even if Wi-Fi status

indicator lights in blue, try restarting the wireless network router.

≥ With some iOS and iTunes versions, it may not be possible to

restart the AirPlay playback if the selector is changed (e.g., “CD”)

or the unit is turned off, during the AirPlay playback.

In this case, select a different device from the AirPlay icon of the

Music App or iTunes and then re-select this unit as the output

speakers. (l 10)

Pairing cannot be done.

≥ Check the Bluetooth

®

device condition.

The device cannot be connected.

≥ The pairing of the device was unsuccessful or the registration has

been replaced. Try pairing the device again. (l 12)

≥ This unit might be connected to a different device. Disconnect the

other device and try pairing the device again. (l 12)

The device is connected but audio cannot be heard

through this unit.

≥ For some built-in Bluetooth

®

devices, you have to set the audio

output to “SC-HC58” manually. Read the operating instructions for

the device for details.

The sound is interrupted.

≥ The device is out of the 10 m communication range. Bring the

Bluetooth

®

device closer to this unit.

≥ Remove any obstacle between this unit and the device.

≥ Other devices that use the 2.4 GHz frequency band (wireless

router, microwaves, cordless phones, etc.) are interfering. Bring

the Bluetooth

®

device closer to this unit and distance it from the

other devices.

≥ Select “MODE 1” for stable communication. (l 12)

The remote control doesn’t work properly.

≥ The remote control and this unit are using a different code.

(l 21, “REMOTE ”)

≥ Is the battery depleted or is the battery inserted incorrectly? (l 4)

AirPlay operations

Bluetooth

®

Remote control

SC-HC58_EG~RQT9759-R.book 20 ページ２０１３年１月９日　水曜日　午前１０時２５分

Stránka sa načítava ...

Panasonic SCHC58EG Návod na obsluhu

Panasonic SCHC58EG Návod na obsluhu

V iných jazykoch

Súvisiace články

Ďalšie dokumenty