Parkside 73787 Operation and Safety Notes

SANDBLASTER GUN PDSP 1000 A1

S ANDBLASTER GUN

Operation and Safety Notes

Translation of original operation manual

PISTOLET NA SPRĘŻONE POWIETRZE

Wskazówki dotyczące obsługi i bezpieczeństwa

Tłumaczenie oryginalnej instrukcji obsługi

PNEUMATIKUS HOMOKSZÓRÓ PISZTOLY

Kezelési és biztonsági utalások

Az originál használati utasítás fordítása

DRUCKLUFT-SANDSTRAHLPISTOLE

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung

PNEVMATIČNA-PESKALNA PIŠTOLA

Navodila za upravljanje in varnostna opozorila

Prevod originalnega navodila za uporabo

PÍSKOV ACÍ PISTOLE

Pokyny pro obsluhu a bezpečnostní pokyny

Překlad originálního provozního návodu

PIESKOV ACIA PIŠTOĽ

Pokyny pre obsluhu a bezpečnostné pokyny

Preklad originálneho návodu na obsluhu

IAN 73787

GB Operation and Safety Notes Page 5

PL Wskazówki dotyczące obsługi i bezpieczeństwa Strona 17

HU Kezelési és biztonsági utalások Oldal 29

SI Navodila za upravljanje in varnostna opozorila Stran 41

CZ Pokyny pro obsluhu a bezpečnostní pokyny Strana 53

SK Pokyny pre obsluhu a bezpečnostné pokyny Strana 65

DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 77

Before reading, unfold the page containing the illustrations and familiarise yourself with all

functions of the device.

Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z

wszystkimi funkcjami urządzenia.

Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék

mindegyik funkcióját.

Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.

Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.

Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend

mit allen Funktionen des Gerätes vertraut.

15

34

C

A EB

1.

2.

2

5 GB

Table of contents

Introduction

Proper use ................................................................................ Page 7

Features and equipment ......................................................... Page 8

Included items ......................................................................... Page 8

Technical data ......................................................................... Page 8

Safety advice ................................................................... Page 9

Operation

Connecting the compressed air source ................................. Page 11

Filling the blast medium container .......................................... Page 11

Using the sandblasting gun .................................................... Page 12

Cleaning ............................................................................... Page 12

Service ................................................................................... Page 13

Warranty ............................................................................. Page 13

Disposal ................................................................................ Page 14

Declaration of Conformity /

Manufacturer ................................................................... Page 14

6 GB

Introduction

The following pictograms are used in these operating

instructions / on the device:

Read instruction manual!

Observe caution and safety notes!

Risk of explosion!

Wear hearing protection, dust protection mask

and protective glasses.

Keep children away from the device!

Never point the device at people or animals.

No smoking!

Dispose packaging and appliance in an

environmentally-friendly way!

7 GB

Introduction

Sandblaster gun PDSP 1000 A1

Q

Introduction

We congratulate you on the purchase of your new device.

You have chosen a high quality product. The instructions for

use are part of the product. They contain important information

concerning safety, use and disposal. Before using the product, please

familiarise yourself with all of the safety information and instructions for

use. Only use the unit as described and for the speciﬁed applications.

If you pass the product on to anyone else, please ensure that you also

pass on all the documentation with it.

Q

Proper use

This device is intended for the removal of rust and paint from metal

surfaces. Any other use or modiﬁcation to the device shall be considered

as improper use and could give rise to considerable risk of accident.

We will not accept liability for loss or damage arising from improper

use. The device is intended for private, domestic use only.

Q

Features and equipment

1

Sandblaster gun

2

Trigger

3

Plug-in nipple for compressed air connection

4

Blast medium container

5

Blast nozzle

8 GB

Q

Included items

1 Sandblaster gun PDSP 1000 A1

1 Operating instructions

Q

Technical data

Max. Working pressure: 8 bar

Recommended working air pressure: 3–5 bar

Compressed air consumption: 130–260 l / min

Nozzle ø: 2.8 mm

Container capacity: 1000 ml

Volume ﬂow rate: typically 200–220 g / Min.

Required air quality: Cleaned and oil-free

Working settings: Working air pressure setting at

the pressure reducer max. 8 bar.

Sound pressure level: 86 dB(A)

Sound power level: 98 dB(A)

Values determined in accordance with EN 14462 (EN1953/A1:2009).

Safety advice

Read all the safety advice and instructions.

Even minor failures to observe the safety advice and instructions could

lead to severe injury.

keep all the safety advice and instructions in a safe place

for future reference.

Safety advice

Introduction / Safety advice

9 GB

Check the device for damage before bringing it into

use. Do not use the device if you discover any defects.

Keep children and other people away while

you are operating the sandblasting gun. Dis-

tractions can cause you to lose control of the device.

RISK OF INJURY! IMPROPER USE! Never point

the device at people or animals.

For your own safety, wear suitable personal

protective equipment.

Wear an approved dust mask /

protective hood!

Wear protective glasses!

RISK OF EXPLOSION! Do not use the sandblasting

gun

1

in environments containing gases, open flames,

fires or gas-operated water heaters.

NO SMOKING!

Work in adequately ventilated spaces only.

Never use oxygen or other combustible gas as the

energy source.

Never exceed the maximum working air pressure of 8 bar.

RECOIL FORCES! High working pressures can

give rise to recoil forces that under certain conditions can result in

danger from continuous loading.

DANGER OF INJURY! Disconnect the device from the com

pressed

air source before carrying out any repairs or maintenance of the

device or moving it to another location.

Safety advice

Introduction / Safety advice

10 GB

DANGER OF INJURY! Disconnect the device from the com-

pressed air source before filling it with blast medium.

NOTE! Please observe the safety advice provided by the manu-

facturer of the blast medium.

Use only materials for the blast medium that are suit-

able for the sandblasting gun. Do not use quartz sand.

There is the danger of toxic silicon dust forming.

Take precautions to ensure that other people are not

contaminated (dust generation).

Ensure that the spent blast medium is trapped and

collected so that it can be disposed of in an environ-

mentally compatible manner.

Do not remove rating plates or labels–they are safety-relevant

parts of the device.

If you are inexperienced in the use of this type of device, you should

seek out information or training to learn how to handle it safely.

Q

Operation

Q

Connecting the compressed air source

NOTE: Operate the sandblasting gun

1

only with cleaned, conden-

sate- and oil-free compressed air and never exceed the maximum

working air pressure at the device of 8 bar.

NOTE: The compressed air source must be ﬁtted with a (ﬁlter) / pres-

sure reducer so that the air pressure can be regulated.

Connect the sandblasting gun to a suitable compressed air source

by connecting the quick-release coupling of the air supply hose with

the plug-in nipple

3

to the sandblasting gun

1

. It locks itself in

place automatically.

Operation

Safety advice / Operation

11 GB

Q

Filling the blast medium container

Always use a suitable blast medium for your sand blasting work.

NOTE: We recommend using a silica-free blast medium

(e.g. ground blast furnace slag) with a grading of 0.2 mm–0.8 mm.

Ensure that the blast medium is completely dry and not too coarse.

NOTE: The maximum particle size is 0.8 mm.

Turn the bayonet cap of the blast medium container

4

to open it.

Pull the blast medium container

4

oﬀ downwards.

Fill the blast medium container

4

with the desired amount of

blast medium.

Ensure that the maximum capacity of the container (1000 ml) is

not exceeded.

Screw the blast medium container

4

back on and lock it in place

by inserting and turning it on to the container lid (see Figs. A).

Q

Using the sandblasting gun

(see Figs. B, C)

Carefully prepare the workpiece before sand blasting it.

Clean it if necessary.

NOTE: Deposits of dust and grease can have a considerably

detrimental eﬀect on the result.

Carefully mask or tape oﬀ everything that is not to be sand blasted.

Ensure that there is always a minimum distance of 20 cm between

the sandblasting gun

1

and the surface being sand blasted.

Switching on:

Press the trigger

2

to start operating the sandblasting gun

1

.

Operation

Safety advice / Operation

12 GB

Switching off:

Release the trigger

2

to stop operating the sandblasting gun

1

.

After you ﬁnish work, disconnect the device from the compressed

air source.

NOTE: First disconnect the hose from the compressed

air source and only then disconnect the compressed

air supply hose from the device. This will ensure that the

compressed air supply hose does not wave around in an uncon-

trolled manner.

Q

Cleaning

DANGER OF INJURY! Always disconnect

the device from the compressed air source before you clean or

maintain it.

Clean the sandblasting gun

1

and blast medium container

4

after you ﬁnish working. Blow out the sandblasting gun

1

and

the blast medium container

4

with compressed air.

Store the sandblasting gun

1

in a dry, enclosed room.

Q

Service

Have your sandblasting gun repaired

only by qualified specialist personnel using original

manufacturer parts only. This will ensure that your sandblast-

ing gun remains safe to use.

Warranty

Operation / Cleaning / Service

13 GB

Q

Warranty

The warranty for this appliance is for 3 years from the

date of purchase. The appliance has been manufactured

with care and meticulously examined before delivery.

Please retain your receipt as proof of purchase. In the

event of a warranty claim, please make contact by tele-

phone with our Service Department. Only in this way

can a post-free despatch for your goods be assured.

The warranty covers only claims for material and maufacturing defects,

but not for transport damage, for wearing parts or for damage to frag-

ile components, e.g. buttons or batteries. This product is for private use

only and is not intended for commercial use.

The warranty is void in the case of abusive and improper handling, use of

force and internal tampering not carried out by our authorized service

branch. Your statutory rights are not restricted in any way by this warranty.

The warranty period will not be extended by repairs made unter warranty

.

This applies also to replaced and repaired parts. Any damage and de-

fects extant on purchase must be reported immediately after unpacking

the appliance, at the latest, two days after the purchase date. Repairs

made after the expiration of the warranty period are subject to pay

ment.

GB

Service Great Britain

Tel.: 0871 5000 720

(0,10 GBP/Min.)

e-mail: k[email protected]

IAN 73787

Warranty

Operation / Cleaning / Service

14 GB

Q

Disposal

The packaging is made entirely of recyclable materials,

which you may dispose of at local recycling facilities.

Do not dispose of the device with your household rubbish!

For details of disposing of the appliance at the end of its useful life,

please contact your district or city council.

Q

Declaration of Conformity / Manufacturer

We, Kompernaß GmbH, the person responsible for documents: Mr

Semi

Uguzlu, Burgstr. 21, D-44867 Bochum, Germany, hereby declare that

this product complies with the following standards, normative documents

and EU directives:

Machinery Directive

(2006 / 42 / EC)

Applicable harmonised standards:

DIN EN 1953:1998+A1:2009

(EN1953:1998+A1:2009), DIN 31000:1979+A1:2007

Type / Device description:

Sandblaster gun PDSP 1000 A1

Date of manufacture (DOM): 03–2012

Serial number: IAN 73787

Declaration of Conformity / Manufacturer

Disposal / Declaration of Conformity / Manufacturer

15 GB

Bochum, 31.03.2012

Semi Uguzlu

- Quality Manager -

We reserve the right to make technical modiﬁcations in the course of

further development.

Declaration of Conformity / Manufacturer

Disposal / Declaration of Conformity / Manufacturer

16

Spis zawartości

17 PL

Spis zawartości

Wstęp

Zastosowanie zgodne z przeznaczeniem ......................... Strona 19

Wyposażenie ....................................................................... Strona 19

Zakres dostawy .................................................................... Strona 20

Dane techniczne .................................................................. Strona 20

Wskazόwki bezpieczeństwa .......................... Strona 21

Obsługa

Podłączenie źrόdła sprężonego powietrza ....................... Strona 23

Napełnienie pojemnika substancją do piaskowania ........ Strona 23

Zastosowanie pistoletu do piaskowania zasilanego

sprężonym powietrzem ....................................................... Strona 24

Czyszczenie .................................................................... Strona 25

Serwis ................................................................................. Strona 25

Gwarancja ...................................................................... Strona 26

Usuwanie ......................................................................... Strona 27

Deklaracja zgodności / Producent .............. Strona 27

18 PL

Wstęp

W niniejszej instrukcji obsługi urządzenia zastosowano

następujące piktogramy:

Przeczytaj instrukcję obsługi!

Przestrzegaj wskazówek ostrzegawczych i

bezpieczeństwa!

Niebezpieczeństwo wybuchu!

Nosić ochronniki słuchu, maskę pyłochronną i

okulary ochronne.

Trzymać urządzenie z dala od dzieci!

Proszę nie kierować urządzenia w kierunku ludzi

oraz / lub zwierząt.

Zakaz palenia!

Opakowanie i urządzenie przekaż do utylizacji zgodnie

z przepisami o ochronie środowiska!

19 PL

Wstęp

Pistolet na sprężone powietrze PDSP 1000 A1

Q

Wstęp

Gratulujemy zakupu nowego urządzenia. Tym samym zde-

cydowali się Państwo na zakup produktu wysokiej jakości.

Instrukcja obsługi jest częścią tego produktu. Zawiera ona

ważne wskazówki dotyczące bezpieczeństwa, użytkowania iutylizacji.

Przed pierwszym użyciem produktu należy zapoznać się ze wszystki-

mi wskazówkami dotyczącymi obsługi ibezpieczeństwa. Używać pro-

duktu wyłącznie zgodnie zjego poniżej opisanym przeznaczeniem.

Wprzypadku przekazania produktu innej osobie należy dołączyć do

niego całą jego dokumentację.

Q

Zastosowanie zgodne z przeznaczeniem

Niniejsze urządzenie przeznaczone jest do usuwania rdzy oraz farby

z powierzchni metalowych. Każde inne zastosowanie lub dokonywanie

zmian na urządzeniu nie jest zgodne z postanowieniami oraz powo-

duje znaczne zagrożenie wypadkiem. Za szkody powstałe na wskutek

zastosowania sprzecznego z przeznaczeniem nie przejmujemy odpo-

wiedzialności. Niniejsze urządzenie przeznaczone jest jedynie do

zastosowania w celach prywatnych.

Q

Wyposażenie

1

Pistolet na sprężone powietrze

2

Dźwignia spustowa

3

Złączka wtykowa dla przyłącza sprężonego powietrza

20 PL

Wskazόwki bezpieczeństwa

Wstęp

4

Pojemnik na substancję do piaskowania

5

Dysza pistoletu do piaskowania

Q

Zakres dostawy

1 Pistolet na sprężone powietrze PDSP 1000 A1

1 Instrukcja obsługi

Q

Dane techniczne

Maks. ciśnienie robocze: 8 bar

Zalecane ciśnienie robocze: 3 – 5 bar

Zużycie powietrza: 130 – 260 l / min

Dysza ø: 2,8 mm

Zawartość pojemnika: 1000 ml

Objętość przepływu: typowo 200 – 220 g / min.

Wymagania jakościowe dla powietrza: czyste oraz pozbawione oleju

Nastawne parametry pracy: nastawne ciśnienie robocze

na reduktorze lub ciśnienio-

mierz z ﬁltrem maks. 8 bar.

Poziom ciśnienia hałasu: 86 dB(A)

Pozom mocy hałasu 98 dB(A)

Wynik pomiarowy dokonany zgodnie z EN 14462 (EN1953/A1:2009).

Stránka sa načítava...

Parkside 73787 Operation and Safety Notes

Tento návod je vhodný aj pre

Parkside 73787 Operation and Safety Notes

v iných jazykoch

Súvisiace články

Ostatné dokumenty