Parkside PSS 65 A1 Original Instructions Manual

SHARPENING STATION PSS 65 A1

SCHÄRFSTATION

Originalbetriebsanleitung

SHARPENING STATION

Translation of the original instructions

URZĄDZENIE DO OSTRZENIA

Tłumaczenie oryginalnej instrukcji obsługi

OSTŘIČKA

Překlad originálního provozního návodu

BRÚSKA

Preklad originá lneho návodu na obsluhu

OSTRILNA POSTAJA

Prevod originalnega navodila za uporabo

ÉLEZŐGÉP

Az originál használati utasítás fordítása

IAN 102874

102874_par_Schärfstation_cover_PL_HU_SI_CZ_SK.indd 2 14.11.14 09:52

GB Translation of the original instructions Page

P L Tłumaczenie oryginalnej instrukcji obsługi Strona

HU Az originál használati utasítás fordítása Oldal

SI Prevod originalnega navodila za uporabo Stran

CZ Překlad originálního provozního návodu Strana

SK Preklad originálneho návodu na obsluhu Strana

DE / AT / CH Originalbetriebsanleitung Seite

Before reading, unfold the page containing the illustrations and familiarise yourself with all

functions of the device.

Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się

z wszystkimi funkcjami urządzenia.

Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik

funkcióját.

Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.

Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.

Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend

mit allen Funktionen des Gerätes vertraut.

102874_par_Schärfstation_cover_PL_HU_SI_CZ_SK.indd 3 14.11.14 09:52

4

18

33

49

63

78

93

1 54

78910111213

632

1415

10

13

16

4

GB IE

Content

Introduction ................................. 4

Intended use ................................4

General description ...................... 5

Scope of delivery .............................5

Function description..........................5

Summary ........................................5

Technical specications .................5

Safety Instructions........................6

Symbols and icons ...........................6

General Safety Instructions for Power

Tools ...............................................6

Further Safety Instructions ..................8

Residual risks ...................................9

Assembly ..................................... 9

Mount the sharpener ......................10

Operation ..................................10

Switching on and off ......................10

Grinding with the grinding disc .......11

Sharpening drills ............................11

Sharpening picks and chisels ...........11

Sharpening knives ..........................12

Sharpening scissors ........................12

Change grinding disc .....................12

Cleaning and maintenance .........13

Cleaning .......................................13

Storage ......................................13

Waste disposal and environmental

protection .................................. 13

Replacement parts/accessories ...14

Trouble Shooting ........................15

Guarantee .................................16

Repair Service ............................17

Service-Center ............................ 17

Importer ....................................17

Translation of the original

EC declaration of conformity ....109

Exploded Drawing ................... 117

Introduction

Congratulations on the purchase of your

new device. With it, you have chosen a

high quality product.

During production, this equipment has

been checked for quality and subjected to

a nal inspection.

The operating instructions constitute

part of this product. They contain

important information on safety, use

and disposal.

Before using the product, familiarise

yourself with all of the operating

and safety instructions. Use the

product only as described and for

the applications specied.

Keep this manual safely and in the

event that the product is passed on,

hand over all documents to the third

party.

Intended use

The sharpening station is suitable for sharp-

ening tools (e.g. drills, knives, scissors,

picks, chisel).

The device is not intended for all other

types of applications (e.g. grinding with

unsuitable grinding tools, grinding with a

coolant solution, grinding hazardous mate-

rials such as asbestos).

The equipment is intended for use in the

eld of DIY. It is not designed for commer-

cial use.

The equipment is designed for use by

adults. Young people under the age of 16

are permitted to use the equipment only

under supervision.

The manufacturer shall not be liable for

damages caused by use other than for the

intended purpose or by incorrect opera-

tion.

5

GB IE

General description

The illustrations can be found

on the front and rear fold-out

pages.

Scope of delivery

Unpack the equipment and check that it is

complete. Dispose of the packaging mate-

rial correctly.

• Appliance

• Sharpener for

knives and scissors

• Sharpener for drills

• Sharpener for picks and chisels

• Spare grinding wheel

• Translation of the original instructions

for use

Function description

The sharpening station is suitable for

sharpening tools (e.g. drills, knives, scis-

sors, picks, chisels). The scope of delivery

contains three sharpeners for this purpose,

which, as a guide and safety device, en-

able precise sharpening and grinding.

Refer to the following descriptions for a

functional description of the controls.

Summary

1 Mains plug

2 Sharpener for knives and

scissors

3 On/off switch

4 Spacer

5 Magnet holder

6 Tool table

7 Retaining screw for

angular adjustment

8 Protective hood

9 Mounting holes for

work bench assembly

10 Grinding disc

11 rotatable drill mount

12 Knurled nut for drill-fastening

13 Release lever for

sharpener

14 Drill holder

15 Adjusting device

16 Grinding wheel nuts

Technical specications

Nominal input voltage

............................. 220 - 240 V~, 50 Hz

Power consumption ...................... 65 W

(S2 10 min)*

Measurement idling speed n

0

... 6700 min

-1

Safety class ..................................... II

Protection category......................... IP 20

Weight ................................ ca. 1,25 kg

Grinding angle range ................15° - 50°

Sharpness drill diameter ............ 3 -10 mm

Sharpness knife width .............. 6 - 51 mm

Sound pressure level

(L

pA

) .............59,3 dB (A); K

pA

= 3 dB (A)

Sound power level (L

wA

)

measured ........73,5 dB(A); K

wA

= 3 dB(A)

* A break is introduced after 10 minutes of

uninterrupted operating duration until the

device temperature differs 2 K (2°C) less than

room temperature.

Noise and vibration values have been

determined according to the standards and

regulations mentioned in the declaration of

conformity.

Technical and optical changes may be

undertaken in the course of further develop-

ment without notice. All dimensions, refer-

ences and information in this instruction

manual are therefore not guaranteed. Legal

claims made on the basis of the instruction

6

GB IE

manual can therefore not be considered as

valid.

The stated vibration emission value was

measured in accordance with a standard

testing procedure and may be used to com-

pare one power tool to another.

The stated vibration emission value may

also be used for a preliminary exposure

assessment.

Warning!

The vibration emission value may

differ during actual use of the

power tool from the stated value

depending on the manner in which

the power tool is used.

Safety precautions aimed at protect-

ing the user should be based on

estimated exposure under actual

usage conditions (all parts of the

operating cycle are to be consid-

ered, including, for example, times

during which the power tool is

turned off and times when the tool

is turned on but is running idle).

Safety Instructions

Symbols and icons

Symbols on the device:

Warning!

Read the instruction manual.

Wear ear protection.

Risk of electric shock! Disconnect

from the mains before carrying out

maintenance and repair work.

Safety class II

Do not dispose of electrical equip-

ment in household waste.

Symbols in the manual:

Warning symbols with in-

formation on damage and

injury prevention.

Instruction symbols (the instruction is

explained at the place of the excla-

mation mark) with information on

preventing damage.

Help symbols with information on

improving tool handling.

General Safety Instructions

for Power Tools

WARNING! Read all safety in-

structions and guidelines care-

fully. Failure to follow the safety

instructions and guidelines may result

in electric shock, re and/or serious

injuries.

The term „power tool“ used in the safety

instructions refers to mains-operated electric

tools (with a mains cable) and to battery-op-

erated electric tools (without a mains cable.

Safe operation:

• Keep work area clear. Cluttered

areas and benches invite injuries.

• Consider work area environ-

ment.

- Do not expose tools to rain. Do not use

tools in damp or wet locations.

Water entering a power tool will in-

crease the risk of electric shock.

- Keep work area well lit.

7

GB IE

lecting equipment, ensure these are

connected and properly used.

• Do not abuse the cord. Never

yank the cord do disconnect it from the

socket. Keep the cord away from heat,

oil and sham edges.

• Secure work. Where possible use

clamps or a vice to hold the work. It is

safer than using your hand.

• Do not overreach. Keep proper

footing and balance at all times.

This enables better control of the power

tool in unexpected situations.

• Maintain tools with care.

Many accidents are caused by poorly

maintained power tools.

- Keep cutting tools sharp and clean for

better and safer performance.

- Follow instruction for lubricating and

changing accessories.

- Inspect tool cords periodically and if

damaged have them repaired by an

authorized service facility.

- Inspect extension cords periodically

and replace if damaged.

- Keep handles dry, clean and free from

oil and grease.

• Disconnect tools. When not in use,

before servicing and when changing

accessories disconnect tools from the

power supply.

Such preventive safety measures reduce

the risk of starting the power tool acci-

dentaIly.

• Remove adjusting keys and

wrenches. Form the habit of check-

ing to see that keys and adjusting

wrenches are removed from the tool

before turning it on. A wrench or a key

left attached to a rotating part of the

power tool may result in personal injury.

• Avoid unintentional starting.

Ensure switch is in “off” position when

plugging in.

- Do not use tools in the presence of

ammable liquids or gases.

Power tools create sparks which may

ignite the dust or fumes.

• Guard against electric shock.

Avoid body contact with earthed or

grounded surfaces (e.g. pipes, radia-

tors, ranges, refrigerators).

• Keep other persons away.

Do not let persons, especially children,

not involved in the work touch the tool

or the extension cord and keep them

away from the work area.

• Store idle tools. When not in use,

tools should be stored in a dry locked-

up place, out of reach of children.

• Do not force the tool. It will do

the job better and safer at the rate for

which it was intended.

• Use the right tool.

- Do not force small tools to do the job

of a heavy duty tool.

- Do not use tools for purposes not in-

tended; for example do not use circular

saws to cut tree limbs or logs.

Use of the power tool for operations dif-

ferent from those intended could result in

a hazardous situation.

• Dress properly.

- Do not wear loose clothing or jewel-

lery, they can be caught in moving

parts.

- Anti-slip footwear is recommended

when working outdoors.

- Wear protective hair covering to con-

tain long hair.

• Use protective equipment.

- Use safety glasses.

- Use face or dust mask if working op-

erations create dust.

• Connect dust extraction equip-

ment. If the tool is provided for the

connection of dust extraction and col-

8

GB IE

• Use outdoor extension leads.

When the tool is used outdoors, use

only extension cords intended for out-

door use and so marked.

• Stay alert, watch what you are

doing and use common sense

when operating a power tool.

Do not use a power tool while you are

tired or under the inuence of drugs,

alcohol or medication. A moment of

inattention white operating power tools

may result in serious personal injury.

• Check damaged parts. This will

ensure that the safety of the power tool

is maintained.

- Before further use of tool, it should be

carefully checked to determine that it

will operate properly and perform its

intended function.

- Check for alignment of moving parts,

binding of moving parts, breakage of

parts, mounting and any other condi-

tions that may affect its operation.

- A guard or other part that is dam-

aged should be properly repaired or

replaced by an authorized service cen-

tre unless otherwise indicated in this

instruction manual.

- Have defective switches replaced by

an authorized service centre.

- Do not use the tool if the switch does

not turn it on and off.

There is a risk of injury.

• Warning.

The use of any accessory or attach-

ment other than one recommended in

this instruction manual may present a

risk of personal injury.

• Have your tool repaired by a

qualied person. This electric tool

complies with the relevant safety rules.

Repairs should only be carried out by

qualied persons using original spare

parts, otherwise this may result in con-

siderable danger to the user..

Further Safety Instructions

• Connect the device only to a power

point with a residual current protective

device (RCD) with a measured residual

current of not more than 30 mA.

• Keep the mains cable and extension

cable away from the grinding disk and

saw chain. In the event that it is dam-

aged or severed, immediately discon-

nect the plug from the socket.

Do not touch the cable before it has

been disconnected from the mains.

Risk of electric shock.

• The replacement of the plug or the con-

nection line must always be executed

by the manufacturer of the electric tool

or his/her customer service in order to

avoid any hazards.

• Only switch the device on once it is

safely xed to the worktop.

• For your own safety only use acces-

sories and attachments which were

stated in the operating instructions or

recommended or specied by the tool

manufacturer.

• Only use grinding discs where the

printed rotational speed is at least as

high as what has been specied on the

name plate of the device.

• Carry out a visual inspection of the

grinding disc before use. Do not use

any damaged or deformed grinding

discs. Replace any damaged or worn

grinding discs.

• Make sure that the sparks produced

by grinding do not present a danger,

e.g. reach people or ignite ammable

substances.

9

GB IE

• Never keep the ngers between the

grinding disc and spark protection

or in close proximity to the protective

hoods. There is a risk of crushing.

• The rotating parts of the device cannot

be covered due to functional reasons.

Therefore, proceed cautiously and hold

the workpiece rmly in order to avoid

slipping which could cause your hands

to come into contact with the grinding

belt or grinding disc.

• The workpiece gets hot during grind-

ing. Do not touch the machined area,

allow it to cool down. There is a risk

of burning. Do not use coolants or the

like.

• If you are tired or have consumed al-

cohol or tablets, do not work with the

device. Always have a break on time.

• Switch the device off and remove the

mains plug

- to loosen a blocked insertion tool,

- if the connection line is damaged or

entangled,

- in case of unusual sounds.

Residual risks

Even if properly operating and handling

this electric tool, some residual risks will

remain. Due to its construction and build,

this electric tool may present the following

hazards:

a) Lung damage, if suitable respiratory

protection is not worn.

b) Hearing damage, if suitable ear pro-

tection is not worn.

c) Damages to health due to

- touching the area of the grinding tool

which was not covered;

- the ejection of pieces from workpiece

or damaged grinding discs.

d) Damage to your health caused by

swinging your hands and arms when

operating the appliance for longer pe-

riods of time or if the unit is not held or

maintained properly.

Warning! During operation, this

electric tool generates an electro-

magnetic eld which, under certain

circumstances, may impair the

functionality of active or passive

medical implants. To reduce the risk

of serious or lethal injuries, we rec-

ommend that persons with medical

implants consult their doctor and the

manufacturer of their medical im-

plant before operating the machine.

Assembly

Caution! Risk of injury!

- Ensure that you have sufcient

space in which to work, and that

you do not endanger other peo-

ple.

- All covers and protective devices

must be assembled properly be-

fore commissioning.

- Disconnect the mains plug before

changing the setting on the de-

vice.

Setting up

Place the sharpening station on rm sur-

face and fasten the device. Ideally, bolt the

drill to the surface. Use the mounting holes

for the work bench assembly (9) in the

baseplate for this.

The screws and nuts required for as-

sembly are not part of the scope of

delivery.

10

GB IE

Mount the sharpener

1. Select one of the three sharpen-

ers.

2. In order to remove a sharpener

from the working position, you

must press down the release le-

ver for the sharpener (13).

3. Remove the sharpener from the

guide rails, upwards.

4. In the storage positions, the

sharpeners are not xed to the

right and left side and can be

easily removed from the guide

rails.

5. In order to fasten the selected

sharpener in the working posi-

tion, from above push this into

the guide rails. Press the sharp-

ener down until it snaps into

place.

The sharpeners also present

a safety device. Never use

this device without a sharp-

ener. Risk of injury!

Operation

Caution! Risk of injury!

- Always disconnect the plug from

the mains socket before working.

- Use only grinding disks and acces-

sories recommended by the manu-

facturer. The use of other insertion

tools and other accessories may

cause risk of injury.

- Never operate the device without

the visual protection disk.

- Switch on the equipment only when

it is safely installed on the work sur-

face.

Despite spark protection, al-

ways wear safety goggles

while working in order to

avoid eye injuries.

Keep your hands away from

the grinding disc and grind-

ing belt when the device is in

operation. Injury hazard!.

Switching on and off

Ensure that the mains voltage

matches the specications on the

rating plate.

Connect the equipment to the mains.

1. To switch on, press the “I” On switch

and the device starts up (see

3).

2. To switch off, press the “0” off switch

and the device switches off (see

3).

After switching on the device, wait until the

device has reached its max. speed. Only

then must you start with the grinding.

The disk will continue to

run after the equipment is

switched off. There is a risk

of injury.

Test run:

Before starting work and after each

change of grinding disk, carry out a test

run of at least 60 seconds with no load.

Switch off the equipment immediately if the

disk runs lumpy, substantial vibrations oc-

cur, or abnormal noises are generated.

11

GB IE

Grinding with the grinding

disc

Sharpening drills

Drills with a diameter of 3-10 mm can be

sharpened.

1. Mount the selected sharpener

(see Mounting sharpener).

2. Remove the drill holder (14) from

the sharpener.

3. Insert the drill into the drill holder

(14).

4. Insert the drill holder (14) into

the adjusting device (15).

5. Push the drill to the front into the

V-nut up to the metal stop. The

cutting edges of the drill must t

closely to the metal surfaces.

6. Using the knurled nut fasten the

drill for drill-fastening (12).

7. Remove the drill holder (14) and

insert it into the rotatable drill

mount (11).

8. Check the alignment of the drill.

The cutting edges of the drill

must be touching the grinding

wheel (10).

9. Switch the device off and grind

the drill.

10. Switch the device off and wait

for the grinding wheel (10) to

stop.

11. Remove the drill holder (14)

and insert it into the rotatable

drill mount (11) by rotating in

by 180°. Using the same adjust-

ment, you can grind the opposite

cutting edge of the drill.

12. Switch the device off and grind

the drill.

13. Switch the device off and wait

for the grinding wheel (10) to

stop.

Sharpening picks

and chisels

1. Mount the selected sharpener

(see Mounting sharpener).

2. Place the blade on the tool table

(6) so that the end to be sharp-

ened ts closely to the edge of

the tool table (6). The magnetic

holder (5) keeps the blade in

position.

3. For small picks, use the spacer

(4).

4. Select the angle according to the

existing bevel angle.

5. Release the retaining screw for

the angular adjustment (7) and

turn the tool table (6) into posi-

tion.

6. Tighten the retaining screw for

angular adjustment (7) again.

7. Switch the device on and move

the tool table (6) equally back

and forth along the grinding

wheel (10).

8. Always use light pressure while

sharpening and slowly push

the blade towards the grinding

wheel (10).

9. Repeat the sharpening process

until all irregularities have been

removed.

10. Switch the device off and wait

for the grinding wheel (10) to

stop.

12

GB IE

Sharpening knives

1. Mount the selected sharpener

(see Mounting sharpener).

2. Insert the blade of the knife right

into the knife sharpening slot.

3. Using light pressing guide the

blade along the grinding wheel

(10) and evenly and slowly pull

the knife towards you.

4. Turn the knife and insert the knife

blade into the opposite knife

sharpening slot.

5. Repeat this grinding process for

this side of the blade as well.

6. Execute the alternating grinding

process until the cutting edge is

burr-free and sharp.

7. Switch the device off and wait

for the grinding wheel (10) to

stop.

The device is not suitable for grind-

ing serrated knives.

Sharpening scissors

1. Mount the selected sharpener

(see Mounting sharpener).

2. Completely open the scissors.

3. Insert the scissor blades into the

scissor sharpening slot.

4. Using light pressure guide the

blade from the screw up to the

tip along the grinding wheel

(10).

5. Remove the scissors from the

sharpening station and turn the

scissors to sharpen the other

blade.

6. Insert the other scissor blade into

the scissor sharpening slot.

7. Using light pressure guide the

blade from the screw up to the

tip along the grinding wheel

(10).

8. Execute the alternating grinding

process until the cutting edges

are burr-free and sharp.

9. Switch the device off and wait

for the grinding wheel (10) to

stop.

The device is not suitable for grind-

ing serrated scissors. The device

is not suitable for grinding pinking

shears.

Change grinding disc

Information on replacement:

• Never operate the device without

protective equipment.

• Ensure that the grinding disc

dimensions match those of the

device.

• Never use separate bushings or

adapters in order to make grind-

ing discs whose hole is too large

t the device.

• Do not use any saw blades.

• Always reassemble the device

completely after replacing the

grinding disc.

Switch the device off and remove

the mains plug.

Allow the device to cool down.

1. Release the grinding wheel nut

(16) in the clockwise direction

(left-handed thread).

2. Remove the grinding wheel (10).

13

GB IE

3. Set up a new grinding wheel

(10). Screw the grinding wheel

nut (16) in the anti- clockwise di-

rection (left-handed thread).

4. Test run:

Before starting work and after

each change of grinding disk,

carry out a test run of at least

60 seconds with no load. Switch

off the equipment immediately if

the disk runs lumpy, substantial

vibrations occur, or abnormal

noises are generated.

Cleaning and

maintenance

Disconnect the plug before adjust-

ment, maintenance or repair.

Have any work not described

in these instructions carried

out by a specialist workshop.

Use only original components.

Allow the equipment to cool

before carrying out any main-

tenance and cleaning work.

There is a risk of burns.

Before each use, check the equipment

for obvious defects such as loose, worn

or damaged components and check that

screws or other parts are sitting correctly.

In particular, check the grinding disk (

10). Replace damaged parts.

Cleaning

Do not use cleaning agents or sol-

vents. Chemical substances may

attack plastic parts of the equipment.

Never clean the equipment under

running water.

• Clean the equipment thoroughly after

each use.

• Clean the surface of the device with a

soft brush or cloth.

Storage

• Store the appliance in a dry place well

out of reach of children.

• Grinding disks must be stored dry and

upright and are not to be stacked.

Waste disposal and en-

vironmental protection

Be environmentally friendly. Return the

tool, accessories and packaging to a recy-

cling centre when you have nished with

them.

Machines are not to be place with

domestic waste.

Hand over the device at an utilization loca-

tion. The plastic and metal parts employed

can be separated out into pure materials

and recycling can be implemented. Ask

your Service Center about this. Defective

units returned to us will be disposed of for

free.

14

GB IE

Replacement parts/accessories

Spare parts and accessories can be obtained at

www.grizzly-service.eu

If you do not have internet access, please contact the Service Centre via telephone

(see “Service-Center” page 17). Please have the order number mentioned below ready.

Position Position Description Order

Instruction Exploded number

manual drawing

10 19+20 Grinding wheel with Grinding wheel nuts 91103590

2 100 Sharpener for knives and scissors 91103591

101 Sharpener for drills 91103592

102 Sharpener for picks and chisels 91103593

15

GB IE

Trouble Shooting

Always disconnect the plug from the mains socket before working.

Danger of electric shock.

Problem Possible Cause Error correction

Device doesn‘t start

Mains voltage missing

Main circuit breaker is tripped

Check the socket, mains cable,

line, mains plug, repairs to be

carried out by qualied electri-

cian if necessary, check main

circuit breaker.

On/off switch (

3) may be

defective

Repair by Customer Care

Engine faulty

Grinding tools do

not move although

the engine is run-

ning

Grinding disc nut (

16)

loose

Tighten grinding disc nut (see

„Changing the grinding disc“)

Workpiece, remaining work-

pieces or remaining grinding

tools block drive

Remove blockages

Engine is slower

and stops

Device is overloaded through

workpiece

Reduce pressure on grinding tool

Workpiece unsuitable

Grinding disc does

not rotate smoothly,

abnormal noises

can be heard

Grinding disc nut (

16)

loose

Tighten grinding disc nut (see

„Changing the grinding disc“)

Grinding disc (

10) faulty

Change grinding disc

16

GB IE

Guarantee

Dear Customer,

This equipment is provided with a 3-year

guarantee from the date of purchase.

In case of defects, you have statutory rights

against the seller of the product. These

statutory rights are not restricted by our

guarantee presented below.

Terms of Guarantee

The term of the guarantee begins on the

date of purchase. Please retain the original

receipt. This document is required as proof

of purchase.

If a material or manufacturing defect

occurs within three years of the date of

purchase of this product, we will repair or

replace – at our choice – the product for

you free of charge. This guarantee requires

the defective equipment and proof of pur-

chase to be presented within the three-year

period with a brief written description of

what constitutes the defect and when it oc-

curred.

If the defect is covered by our guarantee,

you will receive either the repaired product

or a new product. No new guarantee pe-

riod begins on repair or replacement of the

product.

Guarantee Period and Statutory

Claims for Defects

The guarantee period is not extended by

the guarantee service. This also applies for

replaced or repaired parts. Any damages

and defects already present at the time of

purchase must be reported immediately af-

ter unpacking. Repairs arising after expiry

of the guarantee period are chargeable.

Guarantee Cover

The equipment has been carefully pro-

duced in accordance with strict quality

guidelines and conscientiously checked

prior to delivery.

The guarantee applies for all material and

manufacturing defects. This guarantee

does not extend to cover product parts that

are subject to normal wear and may there-

fore be considered as wearing parts (e.g.

lters or attachments) or to cover damage

to breakable parts (e.g. switches, batteries,

or parts made of glass).

This guarantee shall be invalid if the prod-

uct has been damaged, used incorrectly or

not maintained. Precise adherence to all of

the instructions specied in the operating

manual is required for proper use of the

product. Intended uses and actions against

which the operating manual advises or

warns must be categorically avoided.

The product is designed only for private

and not commercial use. The guarantee

will be invalidated in case of misuse or

improper handling, use of force, or inter-

ventions not undertaken by our authorised

service branch.

Processing in Case of Guarantee

To ensure quick handling of you issue,

please follow the following directions:

• Please have the receipt and item num-

ber (IAN 102874) ready as proof of

purchase for all enquiries.

• Please nd the item number on the rat-

ing plate.

• Should functional errors or other de-

fects occur, please initially contact the

service department specied below by

telephone or by e-mail. You will then

receive further information on the pro-

cessing of your complaint.

17

GB IE

GB

IE

• After consultation with our customer

service, a product recorded as defec-

tive can be sent postage paid to the

service address communicated to you,

with the proof of purchase (receipt)

and specication of what constitutes

the defect and when it occurred. In or-

der to avoid acceptance problems and

additional costs, please be sure to use

only the address communicated to you.

Ensure that the consignment is not sent

carriage forward or by bulky goods,

express or other special freight. Please

send the equipment inc. all accessories

supplied at the time of purchase and

ensure adequate, safe transport pack-

aging.

Repair Service

For a charge, repairs not covered by the

guarantee can be carried out by our ser-

vice branch, which will be happy to issue

a cost estimate for you.

We can handle only equipment that has

been sent with adequate packaging and

postage.

Attention: Please send your equipment to

our service branch in clean condition and

with an indication of the defect.

Equipment sent carriage forward or by

bulky goods, express or other special

freight will not be accepted.

We will dispose of your defective devices

free of charge when you send them to us.

Service-Center

Service Great Britain

Tel.: 0871 5000 720

(£ 0.10/Min.)

E-Mail: [email protected]

IAN 102874

Service Ireland

Tel.: 1890 930 034

(0,08 EUR/Min., (peak))

(0,06 EUR/Min., (off peak))

E-Mail: [email protected]

IAN 102874

Importer

Please note that the following address is

not a service address. Please initially con-

tact the service centre specied above.

Grizzly Tools GmbH & Co. KG

Stockstädter Straße 20

63762 Großostheim

Germany

www.grizzly-service.eu

18

PL

Spis tresci

Wstęp ........................................18

Przeznaczenie ............................ 18

Opis ogólny ............................... 19

Zawartość opakowania ..................19

Opis działania ..............................19

Przegląd .......................................19

Dane techniczne ......................... 19

Zasady bezpieczeństwa .............20

Symbole i piktogramy .....................20

Dalsze zasady bezpieczeństwa .......23

Zagrożenia ogólne ........................24

Montaż ...................................... 24

Montaż przyrządów do ostrzenia ....25

Obsługa.....................................25

Włączanie i wyłączanie .................25

Szlifowanie z tarczą szlierską ............

Ostrzenie wierteł ...........................26

Ostrzenie przecinaków i dłut ...........26

Ostrzenie noży ..............................27

Ostrzenie nożyc ............................27

Wymiana tarczy szlierskiej ............27

Oczyszczanie i konserwacja ....... 28

Oczyszczanie ...............................28

Przechowywanie urządzenia ..... 28

Usuwanie i ochrona środowiska 29

Części zamienne/Akcesoria ........ 29

Poszukiwanie błędów ................30

Gwarancja .................................31

Serwis naprawczy .....................32

Service-Center ............................ 32

Importer ....................................32

Tłumaczenie oryginalnej

deklaracji zgodności WE............. 110

Rysunek samorozwijający .......117

Wstęp

Gratulujemy zakupu nowego urządzenia.

Zdecydowali się Państwo na zakup warto-

ściowego produktu.

Nie da się wykluczyć tego, że w pojedyn-

czych przypadkach w urządzeniu lub przy

nim wzgl. w wężach mogą się znaleźć

pozostałości wody lub smaru. Nie jest to

brakiem ani uszkodzeniem, czy powodem

do troski o urządzenie.

Instrukcja obsługi jest częścią składo-

wą produktu. Zawiera ona ważne

wskazówki dotyczące bezpieczeń-

stwa, eksploatacji i utylizacji. Przed

rozpoczęciem użytkowania produktu

należy się zapoznać ze wszystkimi

wskazówkami dotyczącymi obsługi

i bezpieczeństwa. Produkt należy

użytkować tylko zgodnie z opisem i

podanym przeznaczeniem. Instrukcję

należy przechowywać starannie, a

w przypadku przekazania produktu

osobom trzecim należy dostarczyć

nabywcy kompletną dokumentację.

Przeznaczenie

Stacja ostrzenia przeznaczona jest do

ostrzenia narzędzi (np. wierteł, noży, no-

życ, przecinaków, dłut).

Urządzenie nie nadaje się do wszelkich

innych rodzajów zastosowań (np. do szli-

fowania z użyciem nieodpowiednich na-

rzędzi szlierskich, szlifowania z użyciem

chłodziwa, szlifowania materiałów niebez-

piecznych dla zdrowia, np. azbestu).

Urządzenie jest przeznaczone do amator-

skich prac w gospodarstwie domowym.

Nie jest ono przeznaczone do stałego sto-

sowania w celach zarobkowych.

Urządzenie może być używane tylko

19

PL

przez osoby dorosłe. Osoby młodociane

powyżej 16 roku życia mogą używać

urządzenia tylko pod nadzorem.

Producent nie odpowiada za szkody wy-

wołane niezgodnym z przeznaczeniem

użytkowaniem lub nieprawidłową obsługą

urządzenia.

Opis ogólny

Ilustracje znajdują się na okład-

ce przedniej i tylnej.

Zawartość opakowania

Rozpakuj urządzenie i sprawdź, czy jest

ono kompletne. Prawidłowo posegreguj i

usuń materiały opakowania.

• Urządzenie

• Przyrząd do ostrzenia

noży i nożyc

• Przyrząd do ostrzenia wierteł

• Przyrząd do ostrzenia przecinaków i dłut

• Zamienna tarcza szlierska

• Instrukcja obsługi

Opis działania

Stacja ostrzenia przeznaczona jest do

ostrzenia narzędzi (np. wierteł, noży,

nożyc, przecinaków, dłut). W komple-

cie zawarte są trzy różne przyrządy do

ostrzenia, obejmujące prowadnicę i za-

bezpieczenie ochronne i umożliwiające

precyzyjne ostrzenie oraz szlifowanie.

Funkcje elementów urządzenia są podane

w poniższym opisie.

Przegląd

1 wtczka

2 Przyrząd do ostrzenia noży i

nożyc

3 Włącznik/wyłącznik

4 przykładka dystansowa

5 uchwyt magnetyczny

6 podkładka narzędziowa

7 śruba ustalająca do

regulacji kąta

8 Osłona ochronna tarczy szlier-

skiej

9 otwory montażowe do

montażu do stołu roboczego

10 tarcza szlierska

11 obrotowy uchwyt wiertarski

12 nakrętka radełkowana do moco-

wania wiertła

13 dźwignia zwalniająca do

przyrządów do ostrzenia

14 uchwyt wiertła

15 przyrząd do regulacji

16 nakrętka tarczy szlierskiej

Dane techniczne

Znamionowe napięcie

wejścia

............................. 220 - 240 V~, 50 Hz

Pobór mocy ................................. 65 W

(S2 10 min)*

Prędkość obrotowa

znamionowa n

0

..................... 6700 min

-1

Klasa zabezpieczenia ...................... II

Typ zabezpieczenia ....................... IP 20

Ciężar ................................. ca. 1,25 kg

Zakres kąta ostrzenia ................15° - 50°

Ostrzenie wierteł o średnicy ...... 3 -10 mm

Ostrzenie noży o szerokości ..... 6 - 51 mm

Poziom ciśnienia akustycznego

(L

pA

) .............59,3 dB (A); K

pA

= 3 dB (A)

Poziom mocy akustycznej (L

wA

)

zmierzony ......73,5 dB(A); K

wA

= 3 dB(A)

* Po nieprzerwanej pracy przez 10 minut na-

stępuje przerwa, do momentu schłodzenia się

urządzenia do temperatury odbiegającej od

temperatury otoczenia o mniej niż 2 K (2°C).

20

PL

Parametry akustyki i wibracji zostały okre-

ślone zgodnie z normami wymienionymi w

Deklaracji Producenta.

Zmiany techniczne i optyczne mogą być

wprowadzane bez zapowiedzi w trakcie

procesu dalszego rozwoju urządzenia.

Wszelkie wymiary, wskazówki i dane poda-

ne w niniejszej instrukcji obsługi są w związ-

ku z tym podawane w sposób niewiążący.

Roszczenia zgłaszane na podstawie treści

instrukcji obsługi są nieważne.

Podana wartość emisji drgań została zmie-

rzona metodą znormalizowaną i może

być wykorzystywana do porównań urzą-

dzenia elektrycznego z innymi urządze-

niami. Podana wartość emisji drgań może

też służyć do szacunkowej oceny stopnia

ekspozycji użytkownika na drgania.

Ostrzeżenie: Wartość emisji drgań

może się różnić w czasie korzystania

z urządzenia od podanej wartości,

jest to zależne od sposobu używania

urządzenia.

Istnieje konieczność określenia i

zastosowania środków ochrony

użytkownika, opartych na ocenie

ekspozycji w rzeczywistych warun-

kach używania urządzenia (należy

przy tym uwzględnić wszystkie części

cyklu roboczego, na przykład okresy

czasu, w których urządzenie elek-

tryczne jest wyłączone bądź jest włą-

czone, ale pracuje bez obciążenia).

Zasady bezpieczeństwa

Symbole i piktogramy

Zasady bezpieczeństwa/symbole

na urządzeniu

Uwaga!

Przeczytaj instrukcję obsługi urzą-

dzenia i stosuj się do niej.

Noś okulary ochronne.

Niebezpieczeństwo porażenia

prądem elektrycznym! Przed roz-

poczęciem jakichkolwiek prac przy

urządzeniu wyjmij wtyczkę siecio-

wą z gniazdka.

Klasa zabezpieczenia II

Urządzeń elektrycznych nie należy

wyrzucać razem z odpadami do-

mowymi

Symbole w instrukcji obsługi

Symbol niebezpieczeństwa z

informacjami na temat ochro-

ny osób i zapobiegania szko-

dom materialnym.

Znak nakazu (w miejscu wykrzyk-

nika objaśnienie nakazu) z infor-

macjami na temat zapobiegania

szkodom.

Znak informacyjny ze wskazówka-

mi ułatwiającymi posługiwanie się

urządzeniem.

Ogólne zasady

bezpieczeństwa

UWAGA!

Przy użytkowaniu narzędzi elektrycz-

nych należy przestrzegać podanych

poniżej podstawowych środków

bezpieczeństwa, zabezpieczających

przed porażeniem prądem elektrycz-

nym, zranieniem i pożarem.

Przed użyciem elektronarzędzia pro-

Stránka sa načítava...

Parkside PSS 65 A1 Original Instructions Manual

Parkside PSS 65 A1 Original Instructions Manual

v iných jazykoch

Súvisiace články

Ostatné dokumenty