Dometic RTX1000, RTX2000, SPX1200T Mercedes Benz Actros, Antos, Arocs Návod na inštaláciu

Typ
Návod na inštaláciu
1
1
1
1
1
1
1
7
7
1
7
8 Nm
10 Nm
2$
q e
5 mm
t
100
t
100
860
330315
175
t 100
t
s
a
o
u
i
y
r
q
w
e
d f
g
h j k
2)
2$2#2@2!
l 1(
d 4 m
Ø 8,5 mm
8x
RTX1000, RTX2000
Actros/Antos/Arocs SFTP
1
2
4
6
7
3
8
55
RTX1000-2000-SPX1200T-MB-SFTP--I-16s.book Seite 1 Dienstag, 8. Oktober 2019 11:42 11
2
YOUR LOCAL DEALER
dometic.com/dealer
YOUR LOCAL SALES OFFICE
dometic.com/sales-offices
A complete list of Dometic companies, which comprise the Dometic Group, can be found in the public filings of:
DOMETIC GROUP AB Hemvärnsgatan 15 SE-17154 Solna Sweden
YOUR LOCAL SUPPORT
dometic.com/contact
A B
d
24 V
1.
< 0,3 m
j
h
1*
1(
k
2)
2!2#
2@
2@
1
2.
f
g
1
1
1
1
1
7
7
1
7
M6
M6 x 90
o
a
s
u
10 x 48
i
10 x 28
1
8 Nm
t
y
r
w
M8 x 40
M8
14 x 18
8,5 x 20
a
b
c
0
9
4445102638 10/2019
RTX1000-2000-SPX1200T-MB-SFTP--I-16s.book Seite 2 Dienstag, 8. Oktober 2019 11:42 11
1
t
s
a
o
u
i
y
r
w
df
g
hjk
2) 2#2@2!
l1(
Ø 10 mm
8x
291286
60 t 100
t
100
t
100
779
d 4 m
d 17°
CoolAir
SPX1200C
SPX1200T
Actros/Antos/Arocs SFTP
1
2
3
4
7
6
8
5
RTX1000-2000-SPX1200T-MB-SFTP--I-16s.book Seite 1 Dienstag, 8. Oktober 2019 11:42 11
2
YOUR LOCAL DEALER
dometic.com/dealer
YOUR LOCAL SALES OFFICE
dometic.com/sales-offices
A complete list of Dometic companies, which comprise the Dometic Group, can be found in the public filings of:
DOMETIC GROUP AB Hemvärnsgatan 15 SE-17154 Solna Sweden
YOUR LOCAL SUPPORT
dometic.com/contact
24 V
1.
< 0,3 m
j
h
1*
1(
k
2)
2!2#
2@
2@
1
2.
f
g
A B
d
1
1
1
1
1
1
M6
M6 x 90
o
a
s
u
10 x 48
i
10 x 28
8 Nm
t
y
r
w
M8 x 40
M8
14 x 18
8,5 x 20
1
2
3
4
d 4,2 m
9 b
c
0
a
d
4445102648 10/2019
RTX1000-2000-SPX1200T-MB-SFTP--I-16s.book Seite 2 Dienstag, 8. Oktober 2019 11:42 11
CLIMATE CONTROL
COOLAIR
RTX1000, RTX2000, SPX1200T
Assembly kit for Mercedes Benz
Actros/Antos/Arocs (SFTP)
Installation Manual . . . . . . . . . . . . . . . . . . 3
Montagesatz für Mercedes Benz
Actros/Antos/Arocs (SFTP)
Montageanleitung . . . . . . . . . . . . . . . . . .17
Kit de montage pour Mercedes Benz
Actros/Antos/Arocs (SFTP)
Instructions de montage. . . . . . . . . . . . . .31
Juego de montaje para Mercedes Benz
Actros/Antos/Arocs (SFTP)
Instrucciones de montaje . . . . . . . . . . . . 45
Kit de montagem para Mercedes Benz
Actros/Antos/Arocs (SFTP)
Instruções de montagem . . . . . . . . . . . . 59
Set di montaggio per Mercedes Benz
Actros/Antos/Arocs (SFTP)
Indicazioni di montaggio . . . . . . . . . . . . 73
Montageset voor Mercedes Benz
Actros/Antos/Arocs (SFTP)
Montagehandleiding . . . . . . . . . . . . . . . 87
Monteringssæt til Mercedes Benz
Actros/Antos/Arocs (SFTP)
Monteringsvejledning . . . . . . . . . . . . . . 101
Monteringssats för Mercedes Benz
Actros/Antos/Arocs (SFTP)
Monteringsanvisning . . . . . . . . . . . . . . .114
Monteringssett for Mercedes Benz
Actros/Antos/Arocs (SFTP)
Monteringsanvisning . . . . . . . . . . . . . . . 127
Asennussarja Mercedes Benz
Actros/Antos/Arocs (SFTP)
Asennusohje . . . . . . . . . . . . . . . . . . . . . . 141
Монтажный комплект для
Mercedes Benz
Actros/Antos/Arocs (SFTP)
Инструкция по монтажу . . . . . . . . . . . .154
Zestaw montażowy do Mercedes Benz
Actros/Antos/Arocs (SFTP)
Instrukcja montażu . . . . . . . . . . . . . . . . . 168
Montážna súprava pre Mercedes Benz
Actros/Antos/Arocs (SFTP)
Návod na montáž . . . . . . . . . . . . . . . . . .182
Montážní sada pro vozidla
Mercedes Benz
Actros/Antos/Arocs (SFTP)
Návod k montáži. . . . . . . . . . . . . . . . . . . 196
Szerelőkészlet a következőkhöz:
Mercedes Benz
Actros/Antos/Arocs (SFTP)
Szerelési útmutató . . . . . . . . . . . . . . . . . 210
EN
DE
FR
ES
PT
IT
NL
DA
SV
NO
FI
RU
PL
SK
CS
HU
RTX1000-2000-SPX1200T-MB-SFTP--I-16s.book Seite 1 Dienstag, 8. Oktober 2019 11:38 11
RTX1000-2000-SPX1200T-MB-SFTP--I-16s.book Seite 2 Dienstag, 8. Oktober 2019 11:38 11
3
EN
RTX1000/2000, SPX1200T
Original instructions
Please read this instruction manual carefully before installation and
first use, and store it in a safe place. If you pass on the product to
another person, hand over this instruction manual along with it.
Contents
1 Explanation of symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1 Using the device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2 Handling electrical cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3 Target group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.1 RTX1000, RTX2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.2 SPX1200T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
6 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6.1 Notes on installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6.2 Removing the roof hatch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6.3 Preparing the unit fixings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6.4 Preparing the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
6.5 Attaching the seal for the cab roof. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
6.6 Fitting the unit in the roof hatch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
6.7 Routing the electrical power supply leads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
6.8 Installing supply lines to the condenser unit (SPX1200T only) . . . . . . . . . . . . . . 12
6.9 Fixing the cover frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7 Configuring the system software . . . . . . . . . . . . . . . . . . . . . . . . . 13
7.1 Entering and exiting configuration mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7.2 P.01: Low voltage shut-down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7.3 P.02: Unit for temperature display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.4 P.05: Tilt sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
8 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
RTX1000-2000-SPX1200T-MB-SFTP--I-16s.book Seite 3 Dienstag, 8. Oktober 2019 11:38 11
EN
Explanation of symbols RTX1000/2000, SPX1200T
4
1 Explanation of symbols
!
!
A
I
2 Safety instructions
The manufacturer accepts no liability for damage in the following cases:
Faulty assembly or connection
Damage to the product resulting from mechanical influences and incorrect
connection voltage
Alterations to the product without express permission from the manufacturer
Use for purposes other than those described in the operating manual
2.1 Using the device
Only use the parking cooler for the purpose specified by the manufacturer
and do not make any alterations or structural changes to the device.
Do not use the parking cooler if it is visibly damaged.
The parking cooler must be installed safely so that it cannot tip over or fall
down.
Installation, maintenance and repair work may only be carried out by
qualified personnel from a specialist company who are familiar with the risks
involved and the relevant regulations.
Do not use the parking cooler near flammable fluids and gases.
Do not operate the parking cooler if the ambient temperature is below 0 °C.
Do not undo the upper cover of the parking cooler in the event of a fire. Use
approved extinguishing agents instead. Do not use water to extinguish fires.
WARNING!
Safety instruction: Indicates a hazardous situation that, if not avoided, could
result in death or serious injury.
CAUTION!
Safety instruction: Indicates a hazardous situation that, if not avoided, could
result in minor or moderate injury.
NOTICE!
Indicates a situation that, if not avoided, can result in property damage.
NOTE
Supplementary information for operating the product.
RTX1000-2000-SPX1200T-MB-SFTP--I-16s.book Seite 4 Dienstag, 8. Oktober 2019 11:38 11
5
EN
RTX1000/2000, SPX1200T Target group
Please inform your vehicle manufacturer if the height entered in your vehicle
documents needs to be altered due to the installation of the parking cooler.
RTX1000/2000 height: 175 mm
SPX1200T height: 60 mm
Disconnect all power supply lines when working on the parking cooler
(cleaning, maintenance, etc).
2.2 Handling electrical cables
Use cable ducts to lay cables through walls with sharp edges.
Do not lay loose or bent cables next to electrically conductive materials
(metal).
Do not pull on the cables.
Attach and lay the cables in such a manner that they cannot be tripped over
or damaged.
The electrical power supply may only be connected by a specialist work-
shop.
The device shall be installed in accordance with national wiring regulations.
The connection to the vehicle's electrical system should be protected as
follows:
power supply: 40 A
voltage monitor: 2 A
Never lay power supply lines (battery leads) in the vicinity of signal or control
cables.
3 Target group
This installation manual contains the essential information and instructions for
installing the parking cooler. It is intended for competent installer technical staff
who are familiar with the guidelines and safety precautions to be applied when
installing lorry accessories.
This installation manual should always be kept with the unit to which it relates.
RTX1000-2000-SPX1200T-MB-SFTP--I-16s.book Seite 5 Dienstag, 8. Oktober 2019 11:38 11
EN
Intended use RTX1000/2000, SPX1200T
6
4 Intended use
A
4.1 RTX1000, RTX2000
The installation kit enables the installation of a CoolAir RTX1000 or RTX2000
parking cooler in a factory-made roof opening (ventilation hatch) of a Mercedes-
Benz Actros, Antos or Arocs SFTP Series cab (excluding Compact Space).
4.2 SPX1200T
The installation kit enables the installation of a CoolAir SPX1200T roof evaporator
in a factory-made roof opening (ventilation hatch) of a Mercedes-Benz Actros,
Antos or Arocs SFTP Series cab (excluding Compact Space).
NOTICE!
The parking cooler is not suitable for installation in construction machines,
agricultural machines or similar equipment. They will not work properly if
exposed to strong vibrations.
Operating parking cooler with voltages other than those specified can
result in damage to the devices.
RTX1000-2000-SPX1200T-MB-SFTP--I-16s.book Seite 6 Dienstag, 8. Oktober 2019 11:38 11
7
EN
RTX1000/2000, SPX1200T Scope of delivery
5 Scope of delivery
CoolAir RTX1000, RTX2000/SPX1200T installation kit for
Mercedes Benz Actros/Antos/Arocs (SFTP)
Item in
fig. 1
Part designation Quantity
Thread insert with flange M8 (RTX only) 8
Spacer sleeve L = 18 mm, 14 mm 8
Thread insert with flange M6 (RTX only) 4
Washer 8.5 x 20 8
Spring washer M8 8
Hex screw M8 x 40 8
Spacer sleeve L = 48 mm, 10 mm 4
Spacer sleeve L = 28 mm, 10 mm 4
Cover frame MB SFTP (Actros, Arocs, Antos) 1
Washer M6 4
 Allen screw with cylindrical head M6 x 90 4
 2.5 m insulating tape (profile: 10 x 20 mm) 1
 Connection cable 6 mm² x 11 m 1
 Cable binder 1
 Maxi Fuse 40 A 1
 Maxi Fuse holder (40 A) 1
 Ring terminal 6 mm², M8 1
 Ring terminal 6 mm², M10 1
 Joint connector 6 m 1
 Blade fuse, 2 A 1
 Fuse holder (2 A) 1
 Ring terminal 0.5 mm², M8 2
 Joint connector 0.5 mm² 1
 1/4" hexagon bit 1
Installation manual 8
RTX1000-2000-SPX1200T-MB-SFTP--I-16s.book Seite 7 Dienstag, 8. Oktober 2019 11:38 11
EN
Installation RTX1000/2000, SPX1200T
8
6 Installation
!
A
6.1 Notes on installation
The following tips and guidance should be followed when installing the parking
cooler:
!
Before installing the parking cooler, check whether any vehicle components
could be damaged or have their function impaired as a result of the installa-
tion.
Check the dimensions of the system to be installed (fig. 2).
The dotted line indicates the middle of the roof hatch opening.
The top cowl of the parking cooler can be painted (fig. 3). The
manufacturer recommends that the painting is done by a specialist paint
shop.
Before installation, check with the vehicle manufacturer whether the vehicle
body is designed for the static weight of the parking cooler and the dynamic
loads created by it when the vehicle is in motion. The manufacturer of the
parking cooler accepts no liability whatsoever in that regard.
CAUTION!
Incorrect installation of the parking cooler may place the safety of the user at
risk.
The manufacturer accepts no liability whatsoever for personal injury or property
damage if the parking cooler is not installed according to this installation
manual.
NOTICE!
The parking cooler may only be installed by qualified personnel from a
specialist company. The following information is intended for technicians
who are familiar with the guidelines and safety precautions to be applied.
The manufacturer only assumes liability for parts included in the scope of
delivery. The validity of the warranty expires if the device is installed
together with third-party parts.
Check whether the roof of the vehicle is able to support the weight of a
person before climbing onto it. Ask the vehicle manufacturer about the
permitted roof loads.
WARNING! Electric shock hazard
Before carrying out any work on electrically operated components, make sure
that they are disconnected from the power supply.
Before installing the parking cooler, disconnect all connections to the vehicle
battery.
RTX1000-2000-SPX1200T-MB-SFTP--I-16s.book Seite 8 Dienstag, 8. Oktober 2019 11:38 11
9
EN
RTX1000/2000, SPX1200T Installation
The downward slope of the roof in forward direction in the area where the
unit is installed must not be more than:
RTX1000: 8°
RTX2000: 20°
SPX1200T: 17°
The assembly parts supplied must not be modified during installation.
The ventilation openings must not be covered over (minimum distance from
other external attachments: 100 mm).
Follow the vehicle manufacturer's guidelines when installing the system and
establishing the electrical connections.
According to the vehicle manufacturer's guidelines, the parking cooler must
be supplied using code E9G (pre-configured electrical equipment) or by
direct connection to the power distribution box behind the cab or direct
connection to the battery.
I
6.2 Removing the roof hatch
Proceed as follows (fig. 6):
Remove all screws and fixings for the existing roof hatch.
Take out the roof hatch.
Remove the sealant around the opening so that the surface is clean and free
of grease.
I
6.3 Preparing the unit fixings
Drill out the 8 factory-made holes to a diameter of 10 mm (fig. 7).
NOTE
After installation of the system, the pre-set parameters on the system software
must be checked (chapter “Configuring the system software” on page 13).
NOTE
Dispose of all waste material, glue, silicon and seals separately. When doing
so, follow the waste disposal requirements applicable in your local area.
RTX1000-2000-SPX1200T-MB-SFTP--I-16s.book Seite 9 Dienstag, 8. Oktober 2019 11:38 11
EN
Installation RTX1000/2000, SPX1200T
10
6.4 Preparing the unit
A
Proceed as follows (fig. 8):
Place the parking cooler on a work surface with the casing facing down.
Screw the 8 self-tapping M8 threaded plugs into the blind holes marked “1”.
To do so, use the 1/4" bit supplied.
Screw the 4 self-tapping M6 threaded plugs into the blind holes marked “7”.
Use a 5 mm hexagon bit to do so.
6.5 Attaching the seal for the cab roof
A
Glue the sealing strip to the cab roof (fig. 9 A).
Follow the contour of the roof hatch opening. The join between the ends of
the seal should be at the back.
Apply a flexible, non-hardening butyl sealant (e.g. SikaLastomer-710) to the
join between the ends of the sealing strip and to the top edge of the sealing
strip (fig. 9 B).
6.6 Fitting the unit in the roof hatch
Place the parking cooler centrally and facing forwards in the roof hatch
opening (fig. 0).
I
A
Fix the parking cooler in place as illustrated (fig. a).
NOTICE!
When preparing the unit on the work surface, make sure it is secured against
falling off.
Make sure that the work surface is clean and level to ensure that the unit is not
damaged.
NOTICE!
Ensure that the surface where the seal between the unit and the cab roof is to
be glued is clean (free of dust, oil, etc.).
NOTE
Once the unit is in position on the vehicle roof, the seal should make contact all
the way round. Only then can a reliable seal be achieved.
NOTICE!
Do not exceed the specified tightening torque under any circumstances. That
is the only way to ensure that the threaded plugs are not pulled out.
RTX1000-2000-SPX1200T-MB-SFTP--I-16s.book Seite 10 Dienstag, 8. Oktober 2019 11:38 11
11
EN
RTX1000/2000, SPX1200T Installation
6.7 Routing the electrical power supply leads
D
!
A
If the vehicle is not pre-configured for electrical equipment (code E9G), connect
the unit directly to the battery.
When doing so, you should also follow the vehicle manufacturer's guidelines.
When connecting to the battery:
Route the power supply lead as illustrated (fig. b):
Run the wiring loom to the battery compartment along a route where it is
protected.
Connect the power supply negative lead (black) to the battery negative
terminal as illustrated.
Connect the voltage monitor negative lead (black) to the battery negative
terminal as illustrated.
I
Connect the power supply positive lead (red) to the battery positive terminal
as illustrated via a 40 A fuse.
Connect the voltage monitor positive lead (red) to the battery positive
terminal as illustrated via a 2 A fuse.
Connect the wiring loom to the unit and fix with a cable tie in a suitable
position (fig. b 2.).
DANGER!
For EX/III and FL vehicles (according to ADR guideline), a battery master switch
must be installed.
WARNING!
The electrical connections may only be made by competent technical staff
with the appropriate specialist knowledge.
Before carrying out any work on electrically operated components, make
sure that they are disconnected from the power supply.
NOTICE!
The connection to the vehicle's electrical system should be protected by a
40 A fuse for the power supply and a 2 A fuse for the voltage monitor.
The battery must be capable of supplying the required current and voltage
(chapter “Technical data” on page 16).
NOTE
Place the fuse holder no more than 0.3 m from the positive terminal of the
battery.
RTX1000-2000-SPX1200T-MB-SFTP--I-16s.book Seite 11 Dienstag, 8. Oktober 2019 11:38 11
EN
Installation RTX1000/2000, SPX1200T
12
6.8 Installing supply lines to the condenser unit
(SPX1200T only)
Observe the following instructions when installing the supply lines:
Also observe the installation instructions for the condenser unit.
The maximum cable length between the evaporator and condenser unit is
4.20 m (fig. d).
When installing and bending supply lines, avoid narrow radii. Use a suitable
round object as a bending aid. A radius which is too narrow will buckle the
refrigerant line, and the parking cooler will be inoperable.
Shorten any supply line which is not needed by bending a curve.
Apply packing compound (fig. d 1) to prevent water entering between the
rear wall of the truck and the clip.
I
Fasten the supply lines to the rear wall of the truck using the clips provided
(fig. d).
Insert the corrugated piping in the holder provided (fig. d 2).
Put the cover on (fig. d 4).
6.9 Fixing the cover frame
A
Fix the cover frame in place as illustrated (fig. c).
NOTE
If you wish to avoid damaging the rear wall of the truck (drilling a hole), you can
also apply the clip using a suitable adhesive. Observe the instructions provided
by the adhesive manufacturer.
NOTICE!
Tighten the screws carefully in order not to damage the cover frame.
RTX1000-2000-SPX1200T-MB-SFTP--I-16s.book Seite 12 Dienstag, 8. Oktober 2019 11:38 11
13
EN
RTX1000/2000, SPX1200T Configuring the system software
7 Configuring the system software
Before the system is first put into operation, the control unit settings can be
adjusted to suit the various installation conditions. Those adjustments must be
made by the installer (fig. 5).
I
7.1 Entering and exiting configuration mode
Press and hold the button.
Press and hold the button for longer than 3 s.
The display shows the symbol .
The parking cooler switches to configuration mode.
The display shows “P.01” and the symbol flashes.
Scroll through the menu by pressing the or button to select the
desired menu item.
Press the button to open the desired menu item.
Press and hold the button for longer than 3 s to exit configuration mode.
Display
indication
Parameter Meaning
Factory
setting
P.01 Low voltage
shut-down
The battery monitor shuts down the
system at the voltage defined here.
22.8 V
P.02 Unit for tempera-
ture display
The temperature can be displayed in
°C or °F.
°C
P.05 Tilt sensor The tilt sensor can be calibrated to a
zero setting.
NOTE
Configuration mode can still be activated if the low voltage cut-out has
switched off the system and only residual voltage is available.
RTX1000-2000-SPX1200T-MB-SFTP--I-16s.book Seite 13 Dienstag, 8. Oktober 2019 11:38 11
EN
Configuring the system software RTX1000/2000, SPX1200T
14
7.2 P.01: Low voltage shut-down
The battery monitor protects the battery against discharging excessively.
A
If only the power supply voltage specified here is available to the parking cooler,
the system is switched off.
Switch to configuration mode (chapter “Entering and exiting configuration
mode” on page 13).
The display shows “P.01” and the symbol flashes.
Press the button to change the setting.
The current setting is displayed.
Use the or button to select the voltage level for low voltage shut-
down.
The low voltage shut-down setting can be adjusted in 0.1 V increments from
20.0 V to 23.5 V.
I
Press the button to save the setting.
The set value is saved and is then applied when the system is restarted.
You are then returned to the menu and can select another menu item by
pressing the or button.
NOTICE!
If the unit is switched off by the battery monitor, it means the battery charge
level is low. Avoid repeated starting or using electrical equipment. Make sure
that the battery is recharged. As soon as the required voltage is available again,
the system can be operated again.
NOTE
The level for the low voltage shut-down should not be set any lower than the
minimum battery voltage required to be able to start the engine under any
conditions.
As a rule that should be no less than 22 V.
RTX1000-2000-SPX1200T-MB-SFTP--I-16s.book Seite 14 Dienstag, 8. Oktober 2019 11:38 11
15
EN
RTX1000/2000, SPX1200T Configuring the system software
7.3 P.02: Unit for temperature display
The system can display the room temperature in °C or °F.
Switch to configuration mode (chapter “Entering and exiting configuration
mode” on page 13).
The display shows “P.01” and the symbol flashes.
Press the or button to select the menu item P.02.
The display shows “P.02” and the symbol lights up.
Press the button to change the setting.
The code for the current setting is displayed:
0: °C
1: °F
Use the or button to select the desired temperature unit.
Press the button to save the setting.
The set value is saved and is then applied when the system is restarted.
You are then returned to the menu and can select another menu item by
pressing the or button.
7.4 P.05: Tilt sensor
The electronics of the system prevents that the system is switched on when the
vehicle is parked at a slope. Since some vehicles‘ roof already is tilted, the tilt
sensor has to calibrated to the zero setting before first use.
Park the vehicle on a level place.
Switch to configuration mode (chapter “Entering and exiting configuration
mode” on page 13).
The display shows “P.01” and the symbol flashes.
Press the or button to select the menu item P.05.
The display shows “P.05”.
Press the button to change the setting.
The code for the current setting is displayed.
Use the or button to select “1”.
Press the button to save the setting.
The set value is saved and is then applied when the system is restarted.
You are then returned to the menu and can select another menu item by
pressing the or button.
RTX1000-2000-SPX1200T-MB-SFTP--I-16s.book Seite 15 Dienstag, 8. Oktober 2019 11:38 11
EN
Technical data RTX1000/2000, SPX1200T
16
8 Technical data
CoolAir
RTX1000 RTX2000
Cooling capacity: 1200 W 2000 W
Rated input voltage: 24 Vg (20 Vg – 30 Vg)
Max. current consumption: 5 – 25 A 5 – 29 A
Operating temperature range: +5 to +52 °C
Low voltage shutdown: Configurable (chapter “P.01: Low voltage shut-
down” on page 14)
Noise emission: < 70 dB(A)
Dimensions (L x B x H): 645 x 860 x 308 mm
Weight: approx. 23 kg approx. 32 kg
CoolAir SPX1200T
Cooling capacity: 1200 W
Rated input voltage: 24 Vg (20 Vg – 30 Vg)
Max. current consumption: 5 – 25 A
Operating temperature range: +5 bis +52 °C
Low voltage shutdown: Configurable (chapter “P.01: Low voltage shut-
down” on page 14)
Noise emission: < 70 dB(A)
Dimensions (L x B x H): 577 x 778 x 182 mm
Weight: approx. 25.5 kg
RTX1000-2000-SPX1200T-MB-SFTP--I-16s.book Seite 16 Dienstag, 8. Oktober 2019 11:38 11
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228

Dometic RTX1000, RTX2000, SPX1200T Mercedes Benz Actros, Antos, Arocs Návod na inštaláciu

Typ
Návod na inštaláciu