Silvercrest 113364 Operating Instructions Manual

IAN 113364

CONVECTION HEATER SKD 2300 B2

CONVECTION HEATER

Operating instructions

KONVEKTORSKI GRELNIK

Navodila za uporabo

KONVEKTOR

Használati utasítás

KONVEKTOR

Návod na obsluhu

KONVEKTOR

Návod k obsluze

KONVEKTOR

Bedienungsanleitung

GB Operating instructions Page 1

HU Használati utasítás Oldal 21

SI Navodila za uporabo Stran 41

CZ Návod k obsluze Strana 61

SK Návod na obsluhu Strana 81

DE / AT / CH Bedienungsanleitung Seite 101

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of

the device.

Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik

funkcióját.

Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.

Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.

Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

1

SKD 2300 B2

GB

Contents

Introduction ...................................................2

Information concerning these operating instructions .............................. 2

Copyright ............................................................... 2

Limitation of liability ....................................................... 2

Intended use ............................................................ 2

Warning notes ........................................................... 3

Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Risk of electrocution ....................................................... 4

Basic safety guidelines ..................................................... 5

Risk of injury if batteries are improperly handled ................................ 7

Before use ....................................................8

Package contents and transport inspection ..................................... 8

Disposal of packaging materials ............................................. 8

Set-up location requirements ................................................ 9

Before initial use ........................................................10

Electrical connection .....................................................10

Inserting the batteries in the remote control ....................................10

Operating components .........................................11

Installation ...................................................12

Fitting the feet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Wall mounting ..........................................................12

Handling and operation ........................................13

Switching the appliance on and oﬀ ..........................................13

Selecting the temperature ................................................. 14

Select heat setting ....................................................... 14

Switching on the fan .....................................................14

Set heating time .........................................................15

Overheating protection ...................................................15

Frost protection function ...................................................15

Cleaning .....................................................16

Transport and storage .........................................16

Disposal .....................................................16

Disposing of the batteries .................................................17

Troubleshooting ..............................................17

Fault causes and rectiﬁcation ...............................................17

Appendix ....................................................18

Technical data ..........................................................18

Notes concerning the EC Declaration of Conformity ............................ 18

Warranty ..............................................................19

Service ................................................................19

Importer ...............................................................19

2

SKD 2300 B2

GB

Introduction

Information concerning these operating instructions

Congratulations on the purchase of your new appliance.

You have selected a high-quality product. The operating instructions are part of

this product. They contain important information on safety, usage and disposal.

Before using the product, familiarise yourself with all handling and safety guide-

lines. Use the product only as described and for the range of applications speci-

ﬁed. Please also pass these operating instructions on to any future owner(s).

Copyright

This documentation is protected by copyright.

Any copying or reproduction, including in the form of extracts, or any repro-

duction of images (even in a modiﬁed state), is permitted only with the written

authorisation of the manufacturer.

Limitation of liability

All the technical information, data and instructions regarding installation, connec-

tion and operation contained in these operating instructions corresponds to the

latest information available to us at the time of printing and takes our previous

experience and know-how into account.

No claims can be derived from the details, illustrations and descriptions in these

instructions.

The manufacturer assumes no responsibility for damage caused by failure to

observe these instructions, improper use, incompetent repairs, unauthorised

modiﬁcations or for the use of non-approved replacement parts.

Intended use

This appliance is intended only for the heating of indoor living spaces and only

for domestic use. This device can be used free standing or mounted on a wall.

This appliance is not intended for use in areas where special conditions may

apply, such as corrosive or potentially explosive atmospheres (dust, vapour or

gas). Do not use the appliance outdoors. It is not intended for any other or more

extensive use.

Claims of any kind for damage arising as a result of incorrect use will not be

accepted. The risk shall be borne solely by the user.

3

SKD 2300 B2

GB

Warning notes

The following warning notice types are used in these operating instructions:

DANGER

A warning notice at this hazard level indicates an imminently

hazardous situation.

If the hazardous situation is not avoided, it could result in death or serious

physical injury.

► Follow the instructions in this warning notice to avoid the risk of death or

serious injury.

WARNING

A warning notice at this hazard level indicates a potentially

hazardous situation.

Failure to avoid this hazardous situation could result in injury.

► Follow the instructions in this warning notice to prevent injury.

CAUTION

A warning notice at this hazard level indicates a potential for

property damage.

Failure to avoid this situation could result in property damage.

► Follow the instructions in this warning notice to prevent property damage.

NOTE

► A note provides additional information that will assist you in using the

appliance.

4

SKD 2300 B2

GB

Safety

In this section, you will ﬁnd important safety instructions for using the appliance.

This appliance complies with statutory safety regulations. Improper use may

result in personal injury and property damage.

Do not cover the appliance!

Covering the appliance can lead to overheating and

thus result in a ﬁre!

Caution! Hot surface!

This symbol warns of hot surfaces on the appliance.

There is a risk of burns!

Risk of electrocution

DANGER

Risk of fatal injury from electrocution!

Contact with live cables or components can result in fatal

injury!

Please observe the following safety guidelines to prevent electrical hazards:

► Do not use the appliance if the power cable or the plug are damaged.

► Before using the appliance again, have a new mains power cable installed

by an authorised specialist.

► The appliance housing must not be opened under any circumstances. There

is a risk of electric shock if live connections are touched and the electrical

and mechanical structure is changed.

5

SKD 2300 B2

GB

Basic safety guidelines

To ensure safe operation of the appliance, follow the safety

guidelines set out below:

■ Check the appliance for visible external damage before use.

Do not operate a appliance that has been damaged or

dropped.

■ If the appliance’s mains power cable is damaged, it must be

replaced by the manufacturer, the manufacturer’s customer

service department or by a qualiﬁed technician so that risks

can be avoided.

■ This appliance may be used by children aged 8 years and

above and by persons with limited physical, sensory or mental

capabilities or lack of experience and knowledge, provided

that they are under supervision or have been told how to use

the appliance safely and are aware of the potential risks.

Children must not use the appliance as a plaything. Cleaning

and user maintenance tasks may not be carried out by children

unless they are supervised.

■ Children younger than three years old should be kept away

from the appliance unless they are constantly monitored.

■ Children older than 3 and younger than 8 years of age may

only switch the appliance on and oﬀ if they are supervised

or instructed in the safe use of the appliance and have un-

derstood the resulting dangers, provided that the appliance

is located or installed in its normal operating position.

■ Children older than 3 and younger than 8 years of age may

not plug in, regulate or clean the appliance and may not

carry out user maintenance tasks.

■ Children should be supervised to ensure that they do not

play with the appliance.

■ Caution – some parts of the product may be very hot and

cause burns. Be particularly careful when children and

vulnerable persons are present.

6

SKD 2300 B2

GB

■ The metal surfaces of the appliance can become hot.

Therefore, only hold the appliance by the handles

9

.

■ All repairs must be carried out by authorised specialist com-

panies or by the Customer Service department. Improper re-

pairs can pose signiﬁcant risks to the user. It will also invali-

date any warranty claims.

■ Defective components must always be replaced with original

replacement parts. Only by using original replacement parts

can it be assured that the safety requirements are being com-

plied with.

■ Protect the appliance from penetration by moisture and liquids.

■ Always unplug the appliance from the mains power socket

before cleaning.

■ Always disconnect the power cable from the mains power

socket by pulling on the plug; never pull on the cable.

■ Avoid using extension cables.

■ Do not use the appliance in the vicinity of naked ﬂames.

■ The appliance must not be placed immediately under or over

a mains power socket.

■ Do not use this heater together with a programmable switch,

a timer, a separate remote control system or any other system

which switches on the heater automatically, as this could lead

to a ﬁre risk if the heater is covered or set up incorrectly.

■ Disconnect the plug from the mains power socket if the appli-

ance malfunctions and also during thunderstorms.

■ The appliance must not be used in the immediate vicinity of

a bath, a shower or a swimming pool.

■ The appliance is to be installed so that a person in the bath

or shower is unable to touch the switch and other controls.

■ Do not expose the appliance to spray and/or dripping water

and do not place any objects ﬁlled with liquid, such as vases

or open drink containers, on or near the appliance.

7

SKD 2300 B2

GB

Risk of injury if batteries are improperly handled

WARNING

►

Keep batteries out of the reach of children. Children might

put batteries into their mouth and swallow them. If a

battery has been swallowed, seek medical assistance

IMMEDIATELY.

► Do not throw batteries into a ﬁre. Never subject batteries

to high temperatures.

► Risk of explosion! Do not charge batteries unless they

are explicitly labelled as "rechargeable".

► Do not open the batteries or short-circuit them.

► Do not mix diﬀerent types of batteries. Due to increased

risk of leakage, empty batteries should be removed.

The batteries should also be removed from the remote

control if it is not being used for long periods.

► Battery acid leaking from a battery can cause skin ir-

ritation. In the event of contact with the skin, rinse with

plenty of water. If the liquid comes into contact with your

eyes, rinse thoroughly with water, do not rub and consult

a doctor immediately.

► When handling leaking batteries, always use coated

gloves and protective goggles!

► The chapter entitled "Initial operation" describes how to

correctly insert and remove batteries.

8

SKD 2300 B2

GB

Before use

Package contents and transport inspection

The appliance is supplied with the following components as standard:

▯ 1 convector heater SKD 2300 B2

▯ 1 remote control

▯ 1 CR2032 button cell

▯ 2 feet

▯ 4 screws for the feet

▯ 4 wall brackets

▯ 4 wall plugs with screws for wall mountings

▯ These operating instructions

NOTE

► Check the package for completeness and for signs of visible damage.

► If any items are missing or damaged as a result of defective packaging or

insuﬃcient care during transportation, contact the Service hotline (see the

chapter Service).

Disposal of packaging materials

The packaging protects the appliance from damage during carriage. The pack-

aging materials have been selected for their environmental friendliness and ease

of disposal, and are therefore recyclable.

Returning the packaging to the material cycle conserves raw materials and

reduces the amount of waste which is generated. Dispose of packaging materials

that are no longer needed in accordance with applicable local regulations.

NOTE

► If possible, keep the appliance's original packaging for the warranty period

so that the appliance can be packed properly for return shipment in the

event of a warranty claim.

9

SKD 2300 B2

GB

Set-up location requirements

For safe and trouble-free operation of the appliance, the set-up location must fulﬁl

the following requirements:

■ The appliance may only be operated in a vertical position and fully assembled.

■ When using the feet, the device must be placed on a ﬁrm, ﬂat and even ﬂoor.

■ When wall mounting, the appliance must only be mounted in a ﬁxed position on

a vertical wall.

■ The minimum clearances between the housing and other objects must be main-

tained: 10 cm at the sides, 30 cm above, 15 cm below (with wall mounting) and

50 cm in front.

■ Ensure that air can always enter and escape freely. Otherwise, there could be a

heat build-up in the appliance.

■ Do not place the appliance in a hot, wet or extremely moist environment or in the

vicinity of ﬂammable materials.

■ The mains power socket must be easily accessible so that the power cable can

be easily disconnected in an emergency.

■ Environmental temperature range: 0 to +40°C

■ Humidity (no condensation): 5–85%

DANGER

Fire risk due to contact with materials!

There is a risk of ﬁre if the heating elements come into contact

with ﬂammable materials!

► Do not place the appliance in the vicinity of curtains and other ﬂammable

materials.

► Do not allow ﬂammable materials (i.e. textiles) to come into contact with

the appliance.

► Do not cover the appliance.

10

SKD 2300 B2

GB

Before initial use

■ Remove all packaging materials and all transport locks from the appliance.

NOTE

►

You may notice a slight smell when using the appliance for the ﬁrst time.

This is normal and is completely harmless.

Electrical connection

To ensure safe and trouble-free operation of the appliance after making the

electrical connection, please observe the following advice:

CAUTION

► Before connecting the appliance, compare the connection data (voltage

and frequency) on the rating plate with that of your mains power supply.

These data must agree so that no damage is sustained by the appliance.

► Ensure that the mains power cable is not damaged and is not running over

hot surfaces and/or sharp edges.

► Ensure that the mains power cable is not taut or knotted.

Inserting the batteries in the remote control

If the battery in the remote control

25

is dead, a new CR2032 battery needs to

be inserted.

♦ Open the battery compartment

30

on the underside of the remote control

25

.

(see description on the rear of the remote control

25

)

♦ Remove the old battery from the remote control

25

.

NOTE

► Please follow the disposal instructions (see section Disposal of batteries).

♦ Insert a new CR2032 battery into the battery compartment

30

.

Ensure the +/- terminals are correctly aligned.

♦ Slide the battery compartment

30

back into the remote control

25

.

11

SKD 2300 B2

GB

Operating components

Control panel

2

Display

3

Air outlet

4

Compartment for the remote control

5

Air inlet

6

Feet

7

Temperature sensor

8

Main switch

9

Carrying handle

10

Display of the selected heat setting

11

“Fan” symbol

12

“Frost protection” symbol

13

Display of the selected measurement unit

14

Fan button

15

Increase temperature

16

Decrease temperature

17

Timer button

18

Runtime display

19

Preset target temperature display

20

Display of the measured actual temperature

21

On/Oﬀ button

22

Infrared receiver for remote control

23

Button to select the measurement unit

24

Button to select the heating setting

25

Remote control

26

Button to select the heating setting

27

Fan button

28

Button to select the measurement unit

29

Decrease temperature

30

Battery compartment

Timer button

32

Increase temperature

33

On/Oﬀ button

34

Wall bracket

35

Screw

36

Screw

37

Wall plug

38

Wall bracket

12

SKD 2300 B2

GB

Installation

CAUTION

► During assembly, lay the appliance on a soft surface, e.g. on a carpet, to

avoid any damage.

Fitting the feet

♦ Place the appliance on a soft surface with the base uppermost.

♦ Fit the feet

6

to the bottom of the appliance using 2 screws

35

on each foot.

Wall mounting

WARNING

► When drilling the holes ensure that any electric cables or other installations

in the wall, such as water pipes, are not damaged.

► The supplied wall plugs

37

are only suitable for mounting in concrete or

stone. Before starting the installation, please check your installation location

carefully for its suitability for the anchors. If in doubt, consult a professional.

NOTE

► When selecting the mounting location make sure that a suitable mains wall

socket is located within the plug-in radius of the mains power cord.

► The feet

6

may not be screwed on if the appliance is wall-mounted.

♦ Mark two drill holes at a minimum height of 487 mm and at a distance of

566 mm (see Fig. drill diagram).

♦ Using a drill and an 8 mm drill bit, drill two holes with a minimum depth of

40 mm.

566 mm

ø 8 mm, 40 mm

min. 487 mm

Fig. drill diagram

♦ Insert the supplied wall plugs

37

into the holes.

♦ Screw the two wall brackets

34

to the wall using the supplied screws

36

.

13

SKD 2300 B2

GB

♦ To ensure that the appliance hangs vertically on the wall, the other two wall

brackets

38

are used as spacers (see Fig. spacers).

Fig. spacers

♦ Screw the two wall brackets

38

onto the underside of the appliance with the

supplied screws

35

.

♦ Hang the appliance from the top into the wall brackets

34

.

NOTE

► To make the mounting more stable, the two wall brackets

38

can also be

screwed to the wall.

Handling and operation

NOTE

► All functions can be used with the buttons on the device as well as with the

remote control

25

.

This section provides you with important information on handling and using the

appliance.

Switching the appliance on and oﬀ

The main switch

8

disconnects the appliance fully from the mains power supply.

♦ Insert the power plug into a mains wall socket.

♦ Switch on the appliance using the main switch

8

ﬁrst; or switch oﬀ at the

main switch last if you are no longer using the appliance.

♦ When switched on, the integrated control lamp in the main switch

8

lights

up.

There will be a beep and the display

2

lights up.

♦ Now press the on/oﬀ button

21

or

33

.

The appliance is now ready for use.

14

SKD 2300 B2

GB

Selecting the temperature

NOTE

► The display

2

shows the set target temperature

19

and measured actual

temperature

20

.

► The temperature measurement is made by the temperature sensor

7

. It

may take some time until the whole room has reached this temperature.

♦ Press the button

23

or

28

to select the unit of measure, to select whether the

temperature display uses °C or °F.

The selected unit of measurement

13

is shown on the display

2

.

♦ Press the "Increase temperature" button,

15

or

32

, to increase the target

temperature

19

up to a maximum of 37°C (99°F).

The selected target temperature

19

is shown on the display

2

.

♦ Press the "Decrease temperature" button,

16

or

29

, to decrease the target

temperature

19

down to a minimum of 5°C (41°F).

The selected target temperature

19

is shown on the display

2

.

Select heat setting

The heat setting determines how quickly the appliance warms up.

The appliance has three heat settings:

■ Level 1: 1000 watts

■ Level 2: 1300 watts

■ Level 3: 2300 watts

♦ Press the button to select the heat setting

24

or

26

repeatedly until the

desired heat setting has been set.

The selected heat setting

10

is shown on the display

2

.

Switching on the fan

The appliance has a fan which can be used to distribute heated air throughout

the room more quickly.

♦ Press the fan button

14

or

27

to switch the fan on or oﬀ.

If the fan is running, the "Fan" symbol

11

appears on the display

2

.

NOTE

► If the fan is switched oﬀ, the heat is concentrated more around the appli-

ance and is not distributed so quickly around the room.

15

SKD 2300 B2

GB

Set heating time

The appliance has a timer that you can use to set the desired heating time between

1 to 24 hours. Once this period is over, the appliance switches oﬀ automatically.

♦ Press the timer button

17

or until the desired runtime

18

is shown on the

display

2

.

♦ To switch the timer oﬀ, press the timer button

17

or repeatedly until no

runtime

18

appears on the display

2

.

Overheating protection

The appliance is ﬁtted with a thermostat-controlled overheating protector. If the

appliance becomes too hot internally, the heating element switches oﬀ automati-

cally. As soon as the appliance has cooled down, the heating element switches

back on.

WARNING

As a general rule, there is a reason for overheating! It can

mean a risk of ﬁre!

► Check that the appliance can suﬃciently dissipate the heat generated: Is

the appliance covered or is it too close to a wall or other obstacle? Is the

fan blocked?

► Check that neither the air inlet

5

nor the air outlet

3

is blocked and

remove the cause.

► If possible, eliminate the problem or contact the Service Hotline (see the

chapter Service).

► Even if you cannot ﬁnd a cause, but the overheating protection triggers a

second time, you must return the appliance to Customer Services for inspec-

tion or repair.

Frost protection function

The appliance has a frost protection function that prevents the room temperature

from falling below the frost line.

♦ Press the button for selecting the heat setting

24

or

26

repeatedly until the

"Frost protection" symbol

12

appears on the display

2

.

NOTE

► As soon as the temperature in the immediate vicinity of the appliance

falls under 5°C (41°F) the appliance will switch on automatically.

► As soon as the temperature climbs above 9°C (48°F), the appliance

switches itself oﬀ and the room temperature will be shown on the

display

2

.

♦ To switch oﬀ the frost protection function, press the button for selecting the heat

setting

24

or

26

repeatedly until the "Frost protection" symbol

12

disappears

from the display

2

.

16

SKD 2300 B2

GB

Cleaning

WARNING

Observe the following safety information to avoid hazards and property

damage:

► Always pull out the plug before cleaning the appliance.

► Only clean the appliance when it is switched oﬀ and cold.

CAUTION

Possible damage to the appliance.

Moisture can cause damage to the appliance.

► To avoid irreparable damage to the appliance, ensure that no moisture

gets into it during cleaning.

■ Never immerse the appliance in water and protect it from splashing or sprayed

water.

■ Allow the appliance to cool down before cleaning to prevent any risk of burns.

■ Clean the housing only with a soft damp cloth and a mild detergent.

■ Remove dust deposits on the protective screen with a vacuum cleaner.

Transport and storage

■ Always carry the appliance using its carrying handles

9

.

■ Disconnect the mains power plug if you do not intend to use the appliance for an

extended period of time.

■ Store the appliance in a dry environment.

Disposal

Never dispose of the appliance in normal domestic waste. This

product is subject to the provisions of the European WEEE (Waste

Electrical and Electronic Equipment) Directive 2012/19/EU.

Dispose of the appliance via an approved waste disposal company or your

municipal waste disposal facility. Please observe applicable regulations.

Please contact your waste disposal facility if you are in any doubt.

17

SKD 2300 B2

GB

Disposing of the batteries

Defective or dead batteries must be recycled according to Directive 2006/66/EC.

Do not dispose of the batteries in the domestic waste. Batteries can contain poi-

sons which are damaging to the environment. Therefore, dispose of the batteries

in accordance with applicable statutory regulations.

Consumers are legally obliged to dispose of used batteries at a collection point

in their town/district or at a retail store. This obligation is intended to ensure that

batteries are disposed of in an environmentally responsible manner.

Dispose of batteries only when they are fully discharged.

Troubleshooting

This section contains important information about fault identiﬁcation and rectiﬁca-

tion.

WARNING

Observe the following safety information to avoid hazards and property dam-

age:

► Repairs to electrical appliances should only be carried out by specialists

trained by the manufacturer. Improper repairs can cause considerable risks

to users and damage to the appliance.

Fault causes and rectiﬁcation

The following table will help you to identify and rectify minor malfunctions:

Malfunction Possible cause Remedy

The appliance

will not switch

on.

The plug is not connected. Put the power plug into the socket.

The mains power socket is not

supplying power.

Check the house mains fuse.

The appliance

switches itself

oﬀ automati-

cally.

The overheating protection has

been triggered.

Allow the appliance to cool down.

Clean the appliance.

The selected temperature has

been reached.

The appliance switches itself back on

automatically as soon as the room

temperature falls.

Select a higher target temperature

19

.

NOTE

► If you are unable to resolve the problem by taking any of the aforemen-

tioned steps, please contact the Customer Service department.

Stránka sa načítava...

Silvercrest 113364 Operating Instructions Manual

Silvercrest 113364 Operating Instructions Manual

v iných jazykoch

Súvisiace články

Ostatné dokumenty