LG VR5942L Používateľská príručka

OWNER’S MANUAL

CLEANING ROBOT

VR594*L

VR594*L*

Before using, please carefully read the Safety Precautions pages to allow for

safe operation of the product. After reading the operation manual, please keep

it in an easily accessible location.

www.lg.com

ENGLISH

ČESKÝ

SLOVAK

MFL67086058

FEATURES

Images of the ﬂoor are obtained from the sensors of the lower camera, and

through this, the location of HOM-BOT will be conﬁrmed,therefore, elaborate

cleaning can be accomplished for every part of the room.

As the height of the HOM-BOT is low (90mm), even the underside of a framed

bed or furniture can be cleaned.

The HOM-BOT also has voice conﬁrmation and instruction that can be easily

understood by the user.

The HOM-BOT can clean all parts of the area by cleaning in zigzag mode and

then in spatial expansion mode.

As the noise levels are at a quiet 60dB(A) , cleaning can be performed at night.

*Less than 60dB(A)

CONTENTS

Safety Precautions

Included with Product

Parts Descriptions

Button Functions

Display Status Information

Before You Start

Overview

1

BEFORE USING

2

HOW TO USE

3

CARE AND MAINTENANCE

26~28

29

How to Install the Home Station

How to Turn the Power Supply On and Off.

How to Start and Stop Cleaning

How to Charge the Battery

Cleaning Modes

Auxiliary Cleaning Modes

Timer Cleaning

Cleaning the Dust Bin

Cleaning the Dust Bin Filter

Cleaning the Brush

Cleaning the Sensor/Charging Terminal

Cleaning the Side Brush

4

ADDITIONAL INFORMATION

5

REFERENCE

2~4

5

6~7

8~9

10

11

12

13

14

15

16~17

18

19

20

21

22

23

24

25

Troubleshooting

Before You Call for Service

Product Speciﬁcations

Open Source Software Notice

30

31~32

ENGLISH

2

SAFETY PRECAUTIONS

The purpose of the safety precautions described below is for the user to use the product safely and correctly

to prevent any unexpected risk or damage.

Basic safety precautions

After reading this manual, please keep it in an easily accessible location.

This is the safety alert symbol. This symbol alerts you to potential hazards that can result in prop-

erty damage and/or serious bodily harm or death.

Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

WARNING

CAUTION

For your safety, do not remove the battery

from the HOM-BOT. If you need to replace

the battery or the HOM-BOT, take it to the

nearest authorized LG Electronics service

center or dealer for assistance.

Doing so can cause ﬁre or product failure.

Never use the HOM-BOT with a battery

and/or home station from any other

product than the HOM-BOT.

Do not use the HOM-BOT when candles or

fragile objects are placed on the ﬂoor.

Doing so can cause ﬁre or product failure.

Always use a dedicated outlet.

Make sure the power cord of the home

station is not crushed under a heavy object

or damaged by contact with sharp objects.

Do not place the home station and the

HOM-BOT near a heating device.

Do not force the power plug to bend. Do

not use the power plug when it has been

damaged or loosened.

Doing so can cause ﬁre or product failure.

Doing so can cause product deformation,

ﬁre, or product failure.

Failure to follow this warning can cause ﬁre

or product failure. If the power cord is

broken, replace it at an LG Electronics

customer care center.

If multiple appliances are connected to an

outlet simultaneously, they can generate

enough heat to cause a ﬁre.

When pulling out the power plug, always

pull it out by grabbing the plug, not the

cord. When pulling out the power plug, do

not to touch the prongs with your ﬁngers.

Doing so can cause an electric shock.

Failure to follow this warning can cause ﬁre

or product failure.

3

SAFETY PRECAUTIONS

Use the HOM-BOT indoors only.

Doing so can cause product failure.

Doing so can cause injury or product failure.

WARNING

CAUTION

ENGLISH

Do not touch the power plug with wet

hands.

Do not use the HOM-BOT while a child or

object is on it. Do not use the HOM-BOT

while an object is hanging from it.

Turn the power supply off immediately if

any abnormal sound, odor, or smoke is

generated from the HOM-BOT.

Do not operate the HOM-BOT in a room

where a child is sleeping.

Do not let children play with the HOM-

BOT.

Doing so can cause injury or product

dam-age.

Doing so can cause injury or product

damage.

Failure to do so can cause ﬁre or product

failure.

Doing so can cause injury or product

damage.

Do not spray or suck in inﬂammable

materials, surfactants, or drinking wa-ter in

the vicinity of the HOM-BOT.

Do not insert any part of the body, such as

a hand or foot, below the brush or wheels

of the HOM-BOT while in use.

Do not operate the HOM-BOT on narrow

and high furniture such as a wardrobe,

refrigerator, desk, table, etc.

Frequently empty the dust bin and main-

tain its cleanliness.

Do not drop the HOM-BOT or subject it to

strong impacts.

Do not expose the HOM-BOT to cold

temperatures (less than 23° F or -5° C) for

a long period of time.

Cleaning will not proceed smoothly on

carpets with tassels or carpets thicker than

10 mm.

It may be more convenient to arrange

them before using the product.

The dust collected in the dust bin can

trigger allergies and may contain harmful

insects.

Using it outdoors can cause product

failure.

The HOM-BOT may bump into furniture

such as chair legs, table legs, thin and

long furniture, etc. while operating.

For a quicker and cleaner performance,

place the chairs on top of the table.

Doing so can cause injury or product

failure.

Doing so can cause injury or product

damage.

Doing so can cause ﬁre or product failure.

* Inﬂammable materials: gasoline, thinner, etc.

* Surfactant: detergent, articles for bath, etc.

Doing so can cause electric shock.

4

SAFETY PRECAUTIONS

Doing so can cause product failure.

Check the following items before use:

ţ Remove fragile or unnecessary objects from the room to be cleaned. For example, remove

expensive ceramics and valuables from the ﬂoor.

ţ%POot use this product in the room where a child is sleeping alone. The child can be hurt.

ţConﬁrm whether the battery has sufﬁcient power, and if it is low, recharge it.

ţEmpty the dust bin after if ﬁlls up.

ţ Close the doors of any room that you do not want the HOM-BOT to enter.

During cleaning, the HOM-BOT may enter another room and continue cleaning.

ţRemove any moisture from the ﬂoor before cleaning.

ţRemove any cables or long strings from the ﬂoor.

ţ

Remove cables, strips, towels, socks, etc. from the ﬂoor so they will not get caught by the brush.

ţ Cleaning will not proceed smoothly on carpets with tassels or carpets thicker than 8 mm

(0.315 in). It may be more convenient to arrange them before using the product.

Tip

CAUTION

Please note, this product is not intended for use in any workshop, commercial ofﬁce, garage or outdoor

environment. It is for normal Domestic internal home use only.

In rare cases, the HOM-BOT’ s brush can

damage the carpet. If this happens,

immediately stop the cleaning operation.

Do not allow the HOM-BOT to suction up

liquids, blades, thumb tacks, kindling, etc.

Do not put sharp objects into the opening

of the HOM-BOT’s supersonic sensor.

Do not use the HOM-BOT when the dust

bin is completely ﬁlled up.

When the robot cleaner is operating, it

may hit the chair leg, desk leg, table leg or

other narrow pieces of furniture.

For quicker and better cleaning, place the

dining chairs on top of the dining table.

Doing so can cause product failure.

These items can cause product failure.

When a carpet has long tassels, the

tassels can be damaged.

Do not let the main frame and charging

terminal of the home station come into

contact with metallic objects.

Doing so can cause product failure. Do

not put any water or detergent on the

HOM-BOT. If liquids get inside of the

HOM-BOT, turn off the power supply and

contact an LG Electronics sales agent or

customer care center.

If the ﬂoor is wet or has wet spots, wipe

them up before using the HOM-BOT.

Failure to do so can cause product failure.

Do not put water, detergent, etc. into the

HOM-BOT.

If you do not use it to save the

energy, turn off the power switch,

and turn on the power switch when

you are cleaning or recharging it.

5

INCLUDED WITH PRODUCT

Figures can be different from actual objects.

Remote controller Home station

HOM-BOT

ENGLISH

6

PARTS DESCRIPTION - HOM-BOT

Figures can be different from actual objects.

Top view

Ultrasonic sensor

Cliff detection sensor

Charging terminal

Brush

Side brush

Wheel

Lower camera sensor

Battery

Power switch

Front view

Rear view

Bottom view

Dust bin cover button

Dust bin cover

Ventilation port

Status indication lamp

Detecting sensor of home station &

receiving sensor of remote controller

7

PART DESCRIPTION – HOME STATION / DUST BIN

ᶀ Figures can be different from actual objects.

Home station

Dust bin

Power lamp

Charging terminal

Reset button

Sponge

ﬁlter

HEPA ﬁlter

Dust bin handle

Dust bin cover

Suction port cover

Dust bin cover opening

button

Power cord ﬁxing groove

ENGLISH

8

BUTTON FUNCTIONS – HOM-BOT

START/STOP

ţ

PresTUIFSTART/ST01CVUUPOUPUVSOUIF)0.#O5PO/oGGPSsUBrU/sUPQDMeBOJOH

ţPresTUIFSTART/ST01CVUUonXIJMFUIF)0.#O5JTPOBOEJUXJMMBVUomBUJ

DBMMZsUBrUDMeBOJOH

ţ*GUIFSTART/ST01CVUUPOJTQressFEEVSJOHBVUomBUJDDMeBOJOHUIF)0.

#OTXJMMsUPQDMeBOJOH

ţPresTBOEIPMEUIFSTART/ST01CVUUonfPSBQQroYJNBUFMZUwPseDPOETUPUVSO

oGGUIF)0.#OT

ţ5IJTQVUTUIF)0.#O5JOUPUIFSUBOE#ZNPEF

ţ

*GUIFCVUUPOJTQressFEXIJMFJOUIFUJNFSNPEFUIFUJNFSseUUJOHXJMMCFDBODFMFE

9

BUTTON FUNCTIONS – REMOTE CONTROL

ţ5IF)0.#05ŜTQPXFSTVQQMZDBOOPUCFUVSOFEPOXJUIUIFSFNPUFDPOUSPM

ţ5PUVSOPOUIFQPXFSTVQQMZVTF45"354501CVUUPOPOUIFUPQPG)0.#05

ţ*OPSEFSUPEPTQPUDMFBOJOHUJNFSDMFBOJOH[JH[BHDMFBOJOHBOETQBUJBMFYQBOTJPODMFBOJOHZPV

must first stop the operation of the HOM-BOT.

ţ*GUIFNBJOGSBNFJTUVSOFEPGGUIFSFNPUFDPOUSPMXJMMOPUCFBDUJWBUFE

ţ5IFQSFTFUGFBUVSFNBZCFTFUPOMZXIFOUIF)0.#05SFUVSOTUPUIFDIBSHJOHTUBOE

ţIf the main switch on the underside of the HOM-BOT is in the off position, the Status display will

flash and sound when the unit is manually placed onto the home station, to indicate that the

main switch is off.

Tip

Start Charging

Directional button

Stop

Spot

Timer

Zigzag cleaning and then

spatial expansion

The HOM-BOT will start cleaning The HOM-BOT will move to the

home station for charging.

The HOM-BOT will move as desired

by the user: to front, rear, left, and

right sides for cleaning.

If the HOM-BOT is in operation it

will be stopped. If it has been set for

timer cleaning, the reservation will be

canceled.

Cleaning will concentrate within a

TQBDFPGBCPVUNGU

The timer can be set from 1-12

hours in the future.

The HOM-BOT will clean while ma-

neuvering in a zigzag pattern and

then expand the cleaning area.

ENGLISH

10

DISPLAY STATUS INFORMATION

ţTPcancFMUIFUJNFSseUUJOHQSesTUIFST01CVUUPOPOUIFSFNoUFcPOUSPMPSUIFSTART/ST01

CVUUPOPOUIF)0.#OT.

Tip

Battery and reserved time indi-

cation

Timer icon

Battery icon

ţ8IJMFwBJUJOHfPSDMeBOJOHUIFSFNBJO

JOHCaUUeSZMevelXJMMCFTIown.

ţ8IJMFwBJUJOHfPSUJNFSDMeBOJOHUIF

SeseSvaUJPOUJNFXJMMCFTIown.

ţ5IJTJOEJcaUesXIFOUJNFSDMeBOJOHIBT

CFFOseUVQ.

ţ'MBTIesXIFOUIFCaUUeSZSFRVJSeT

DIBSHJOHPSXIFOSeUVSOJOHUPUIF

IPNFsUaUJPOBGUFScPNQMeUJOHUIF

cleBOJOH

11

BEFORE YOU START

Check these items before cleaning

Loading the remote control battery

1. Open the battery cover by lifting the rear hook of the remote control.

2. Insert two AAA batteries, checking for +, - nodes while loading.

3. Close the battery cover completely so that the batteries will not fall out.

ţ%POPUVTFUIJTEFWJDFJOBSPPNXIFSFBDIJMEJTMFGUBMPOF5IFDIJMEDPVMECFJOKVSFE

ţ3FNPWFGSBHJMFPSVOOFDFTTBSZPCKFDUTGSPNUIFSPPNUPCFDMFBOFE

Especially, remove expensive ceramics and valuables from the floor.

ţ3FNPWFBOZNPJTUVSFUIBUNJHIUCFPOUIFGMPPS

ţ3FNPWFDBCMFTTUSJQTUPXFMTTPDLTFUDGSPNUIFGMPPSTPUIFZXJMMOPUHFUDBVHIUCZUIFCSVTI

ţ$POGJSNXIFUIFSCBUUFSZDIBSHFJTTVGGJDJFOUBOEJGJUJTMPXSFDIBSHFJU

ţ&NQUZUIFEVTUCJOJGJUJTGVMM

ţ$MPTFUIFEPPSTPGBOZSPPNUIBUZPVEPOPUXBOUUIF)0.#05UPFOUFS%VSJOHDMFBOJOHUIF)0.#05

may enter another room and continue cleaning.

ţ8IFOUIFNPQJTBUUBDIFE)0.#05XJMMOPUCFBCMFUPHPPWFSUISFTIPMETPGNNPSIJHIFS

If you are not planning to use the mop for cleaning, remote the mop before using HOM-BOT.

Precautions while using the remote control

ţ0OMZQSFTTPOFCVUUPOBUBUJNF

ţ%POPUESPQPSTVCKFDUJUUPGPSDFGVMJNQBDU

ţ%POPUTUPSFJUOFBSEFWJDFTUIBUHJWFPGGIFBUGJSFPSIPUBJS

ţ$FSUBJOGMVPSFTDFOUMBNQTTVDIBTXBWFMFOHUIGMVPSFTDFOUMBNQTDBOJOUFSGFSFXJUIUIFBDUJWBUJPOPGUIF

remote control. Therefore, use it as far away as possible from such lamps.

ţ*GUIFSFNPUFDPOUSPMJTGBSGSPNUIF)0.#05XIFOBDUJWBUFEJUNBZGBJMUPPQFSBUFQSPQFSMZ6TFUIF

EFWJDFXJUIJONGUPGUIF)0.#05JGQPTTJCMF

ENGLISH

12

OVERVIEW

1

Install the home station. (page 13)

Insert the power cord plug into an outlet and locate the

station against a wall. If power is not supplied to the

home station, the HOM-BOT will not charge.

2

Turn on the power supply of the HOM-BOT. (page 14)

Turn on the power switch located on the bottom of the

HOM-BOT and press the upper START/STOP button to

turn on the power supply.

* If the power supply is not turned on, refer to page 14.

3

Start cleaning. (page 15)

Press the START/STOP button once again while the

HOM-BOT is turned on. You will hear the sound of clean-

ing and cleaning will begin.

4

Automatic charge. (page 16-17)

The HOM-BOT will self-diagnose and automatically return

to the home station to recharge before the complete dis-

charge of the battery. It takes approximately three hours

to charge the battery.

5

Use auxiliary functions. (page 18-21)

With the remote control, the auxiliary functions can be

used. Auxiliary functions include manual cleaning, spot

cleaning, the timer function, and ultra microﬁber mop

cleaning.

1.5m

2m

13

1. Position the home station against a wall, to prevent sliding dur-

ing docking, on hard level ﬂooring.

Remove objects within 1.5m. to the right and left side and within

2m. to the front.

2. Plug the power cord into an outlet.

Wrap the power cord around the ﬁxed hanger on the back side

of the home station or along the wall surface so that the travel

path of the HOM-BOT will not be obstructed.

3. Fix the home station against the wall so that it does not move.

How to Install the Home Station

ţ Always keep the home station plugged in. If the home station is not plugged in, the HOM-

BOT will not return to the station to charge automatically.

ţ Do not operate the HOM-BOT if it has a damaged cord or plug, if it is not working properly, or

if it has been damaged or dropped. To avoid hazard, the cord must be replaced by LG Elec-

tronics, Inc. or a qualiﬁed service person.

HOW TO INSTALL THE HOME STATION

Tip

Fixing groove of power cord

ENGLISH

1.5m

2m

Turn on the power switch.

14

HOW TO TURN THE POWER SUPPLY ON AND OFF.

To turn the power supply on, turn the HOM-BOT upside down

on a smooth/soft surface and check whether the main power

supply switch is turned on.

If the main power supply switch is turned off, turn on the

switch.

When turning on the power switch, do not press the button

located at the upper section of the HOM-BOT. Operation of

the button can be delayed.

Turn off the power switch if the HOM-BOT will not be used

for a long period of time, in order to protect the battery.

The power switch cover is used for protecting the switch

from the dust. Always keep the cover attached on.

When HOM-BOT is not turned on, press the ‘START/

STOP’ button for more than 1 second. The power supply

will be turned on with the melody sound.

If the power supply is turned on and nothing is done for

ten minutes, the power supply will automatically turn off

to reduce battery consumption.

Press the START/STOP button for two seconds while the

HOM-BOT is turned on. A melody will sound when the

power is turned off. The power will be turned off with the

melody sound.

Turning on the main power supply

Turning on the power supply

Turning off the power supply

ţ The power can be turned off due to the static electricity during

the operation.

- If the power is turned off, turn off the main power switch and

then turn it back on.

ţ*GUIFQower cannot be turned on, do the following.

- Turn on the power switch and wait for more than 3 seconds.

- Press the ‘START/STOP’ button when the power switch is

turned on.

- If the power is not turned on or if there is no display but only

the “Ting” sound, put the HOM-BOT on the home station.

- If there is no change even when HOM-BOT is attached to the

home station, press the reset switch located on the rear side

of the home station while the HOM-BOT is attached on the

home station.

Tip

15

After the HOM-BOT is turned on, press the START/STOP button to

begin cleaning. A melody will sound and cleaning will begin.

Press the START/STOP button during the cleaning cycle to stop cleaning.

When the ‘START/STOP’ button is pressed while the power supply

of the HOM-BOT is turned off, the power will be turned on. Press the

‘START/STOP’ button one more time to clean.

After the HOM-BOT is turned on, press the START button on the re-

mote control. A melody will sound and cleaning will begin.

Press the STOP button during the cleaning cycle to stop cleaning.

The HOM-BOT power supply cannot be turned on by using the re-

mote control if the power of the HOM-BOT is off. When the power is

off, press the ‘START/STOP’ button on the upper side of HOM-BOT

to turn the power on.

When the

START button on the main unit or remote control is pressed, HOM-BOT will start cleaning in

‘Spatial expansion’ mode.

During cleaning, collisions can happen when the sensor cannot detect objects because of their shape.

When this happens, the internal impact detecting sensor will avoid the obstacles by using a backward mo-

tion.

If the HOM-BOT is set to start cleaning at a location away from the home station, put the device on a flat

floor in order to prevent a malfunction of the obstacle detecting sensor. In addition, start cleaning from a lo-

cation where there are not any obstacles such as curtains or walls within 30 cm (11.8 in) of the HOM-BOT.

Using the buttons on the HOM-BOT

Using the remote control

For best results:

ţ Brieﬂy scan the area to be cleaned for big and small objects that will cause difﬁculty if vacu-

umed up.

ţ If cleaning is started when the HOM-BOT is at the home station, the device can rapidly be re-

turned to the home station as the current home position has been accurately read.

HOW TO START AND STOP CLEANING

Tip

ENGLISH

16

HOW TO CHARGE THE BATTERY

The HOM-BOT returns to the home station at the end of a cleaning cycle

or when its battery is running low.

If the HOM-BOT is unable to dock to the home station on its ﬁrst at-

tempt, it will try again until it docks successfully.

When HOM-BOT completed all areas that it can clean, it will re-

turn to the home station even when the battery level is not low.

Automatic charging

If using the HOM-BOT for the ﬁrst time or when charging the battery during cleaning, you can manually

charge the battery.

Method 1. Attach the HOM-BOT to the home station by matching

up the two arrows on the HOM-BOT and the home sta-

tion. A melody will sound and charging will begin.

When the HOM-BOT is attached to the home station, if a

“TING” sound is generated repeatedly, please check the

power switch and turn it on.

Method 2. When the HOMING button of the remote control or the

HOM-BOT is pressed, charging will start by automati-

cally generating a searching sound and returning the

HOM-BOT to the home station.

If the HOM-BOT stays within 10 cm (3.9 in) of the front of the charging terminal while the power supply is

turned on, it will automatically be returned to the home station and charging will begin.

Manual charging

Take the following precautions when using the home station:

ţ If foreign material is caught in the charging terminal, charging may not proceed smoothly.

Wipe the terminal from time to time with a dry cloth after the power plug is disconnected.

ţ To prevent electric shock, do not touch the charging terminal with any metallic objects.

ţ To avoid ﬁre or electric shock, never disassemble or modify the home station.

ţ Do not to place the home station or power plug near to a heating appliance.

Tip

17

Check 1. If the battery is not charging even when the HOM-BOT is at-

tached to the home station, check the following items.

- Turn the power switch on the bottom of the HOM-BOT off

once and then on again.

- Unplug and plug in the power plug on the home station.

- Wipe the terminal on the home station with a dry cloth.

Check 2. If the battery is still not charging after the previous check, try

the following.

- Attach the HOM-BOT to the home station.

-

Press the reset button at the rear of the home station for

three seconds.

If the Battery is Not Charging

The remaining battery charge can be conﬁrmed from the charge indication light, which will indicate charge

as follows:

ţDuring charging, the charge remaining indication light will ﬂicker.

ţ When charging is completed at the home station, only the battery icon will illuminate to save power.

ţ The battery icon will ﬂicker when battery charging is required.

Remaining Battery Charge Indicator

Fully charging

(under charging)

High middle Low

Charging is required

Flickering

If the “TING” sound is repeated when the main unit is at-

tached on the home station, check the main power switch.

HOW TO CHARGE THE BATTERY

ENGLISH

18

CLEANING MODES

When the START button on the main unit or the remote

control is pressed, HOM-BOT operates in the spatial ex-

pansion cleaning mode.

HOM-BOT ﬁrst runs the zigzag cleaning mode and then

switches to spatial expansion mode by dividing the space by

partial squares to clean inside the house thoroughly.

1. Press the ZIGZAG+Cell by Cell button on the remote con-

trol. Zigzag cleaning and then spatial expansion’

2. HOM-BOT cleans total of 6m area in zigzag cleaning mode

by cleaning up to 3m on the left side until it hits the wall.

3. After cleaning in the left direction, HOM-BOT returns to the

starting point and cleans in the right direction until it hits

the wall to clean total area of 6m to complete the zigzag

cleaning mode.

4. And then HOM-BOT switches to the spatial expansion

cleaning mode, which is the automatic cleaning mode.

Spatial expansion cleaning

Zigzag cleaning and then spatial expansion button

ţ The cleaning mode can only be changed with the remote control.

Tip

The 1st stage:

A maximum area of 3 m x 3 m (9.84 ft x

9.84 ft) will be cleaned. (The actual size

of the area will change in accordance

with the shape of the house’s interior.)

The 2nd stage:

The inside of the area will be cleaned in

a zigzag path.

When the 1st and 2nd stages are completed, the device

will move to the next cleaning area and repeat the stages

until the entire inside of the house has been cleaned.

Stránka sa načítava ...

LG VR5942L Používateľská príručka

LG VR5942L Používateľská príručka

V iných jazykoch

Súvisiace články

Ďalšie dokumenty