Parkside PKO 400 B2 Operation and Safety Notes

IAN 89566

K

COMPRESSOR

Operation and Safety Notes

Original operating instructions

D

KOMPRESOR

Pokyny pro obsluhu a bezpečnostní pokyny

Originální návod k obsluze

W

KOMPRESOR

Pokyny pre obsluhu a bezpečnostné pokyny

Originálny návod na obsluhu

T

KOMPRESOR

Wskazówki dotyczące obsługi i bezpieczeństwa

Instrukcją oryginalną

e

COMPRESOR

Indicaţii de siguranţă şi de folosire

Instrucţiuni de utilizare originale

F A C

KOMPRESSOR

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung

D W

T e

COMPRESSOR PKO 400 B2

Anl_4010164.indb 1Anl_4010164.indb 1 25.03.13 15:5525.03.13 15:55

- 2 -

K

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of

the device.

D

Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.

W

Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

T

Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z

wszystkimi funkcjami urządzenia.

e

Înainte de a citi instrucţiunile, deschideţi pagina cu ﬁ guri şi apoi familiarizaţi-vă cu toate funcţiile

aparatului.

F A C

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit

allen Funktionen des Gerätes vertraut.

GB Operation and Safety Notes Page 6

CZ Pokyny pro obsluhu a bezpečnostní pokyny Strana 19

SK Pokyny pre obsluhu a bezpečnostné pokyny Strana 32

PL Wskazówki dotyczące obsługi i bezpieczeństwa Strona 45

RO Indicaţii de siguranţă şi de folosire Pagina 60

DE/AT/CH Bedienungs- und Sicherheitshinweise Seite 74

Anl_4010164.indb 2Anl_4010164.indb 2 25.03.13 15:5525.03.13 15:55

- 3 -

1

2

9

11

2

7

8

3

G

3

4

5

6

8

10

13

14

173

1

1515

19

4

20

21

12

16

18

Anl_4010164.indb 3Anl_4010164.indb 3 25.03.13 15:5525.03.13 15:55

- 4 -

4

7 8

6

29 22 23 24 26 8 27 23 2811

25,26

15

28

27

23

5

242311

8

15

29

25

22

B

Anl_4010164.indb 4Anl_4010164.indb 4 25.03.13 15:5525.03.13 15:55

- 5 -

9 10

11 12

A

max

min

15

16

18

16

D F C

15

21

15

Anl_4010164.indb 5Anl_4010164.indb 5 25.03.13 15:5525.03.13 15:55

GB

- 6 -

Table of contents

The reprinting or reproduction by any other means, in whole or in part, of documentation and papers

accompanying products is permitted only with the express consent of the iSC GmbH.

Subject to technical changes

1. Introduction .................................................................................................................................................. 8

2. Safety regulations ....................................................................................................................................... 8

3. Layout and items supplied ........................................................................................................................10

4. Proper use ...................................................................................................................................................11

5. Technical data ............................................................................................................................................11

6. Before starting the equipment .................................................................................................................. 12

7. Assembly and starting .............................................................................................................................. 12

8. Replacing the power cable ...................................................................................................................... 13

9. Cleaning, maintenance, storage, ordering spare parts and transport ................................................. 13

10. Disposal and recycling ............................................................................................................................. 15

11. Possible causes of failure .......................................................................................................................... 16

12. Declaration of conformity .........................................................................................................................17

13. Warranty certiﬁ cate .................................................................................................................................. 18

Anl_4010164.indb 6Anl_4010164.indb 6 25.03.13 15:5625.03.13 15:56

GB

- 7 -

Caution - Read the operating instructions to reduce the risk of inquiry

Wear ear-muffs. The impact of noise can cause damage to hearing.

Beware of electrical voltage!

Beware of hot parts!

Warning! The equipment is remote-controlled and may start-up without warning.

Caution! Before using for the ﬁ rst time, check the oil level and replace the oil sealing plug!

Important! Do not open the stopcock/pressure regulator until the air hose is connected.

If the equipment is overloaded, the overload switch will shut down in order to prevent damage. Once the

equipment has cooled down, activate the button to start up again.

Anl_4010164.indb 7Anl_4010164.indb 7 25.03.13 15:5625.03.13 15:56

GB

- 8 -

1. Introduction

Congratulations on your new purchase.

You have decided in favor of a high-quality pro-

duct. The operating instructions are a part of this

product. They contain information of importance

for your safety, for the use of the product and for

its disposal. Before you use the product, acquaint

yourself with all the information concerning its

operation and safety. Use the product only as

described and only for the listed areas of applica-

tion. If you hand on the product to other people,

give them all the documentation as well.

2. Safet y regulations

 Caution!

Read all safety regulations and instruc-

tions.

Any errors made in following the safety regu-

lations and instructions may result in an electric

shock, ﬁ re and/or serious injury.

Keep all safety regulations and instruc-

tions in a safe place for future use.

2.1 Safety information

 Important! The following basic safety

actions must be taken when using this

compressor in order to protect the user

from electric shocks and the risk of injury

and ﬁ re. Read and follow these instruc-

tions before using the equipment.

•

Keep your work area tidy

Untidy work areas can result in accidents.

•

Check the ambient conditions

Do not expose the compressor to rain. Never

use the compressor in damp or wet locations.

There is a risk of electric shock! Provide good

lighting. Do not use the compressor near

flammable liquids or gases. There is a risk of

explosion!

•

Protect yourself against electric

shocks

Avoid bodily contact with earthed parts, e.g.

pipes, radiators, cookers and refrigerators.

•

Keep children away!

Do not allow other persons to touch the com-

pressor or cable, keep them away from your

work area.

•

Keep your compressor in a safe place

When unused, the compressor must be stored

in a dry, locked room out of children’s reach.

•

Do not overload your compressor

It will run better and safer within its quoted

capacity range.

•

Wear suitable work clothes

Never wear loose fitting clothes or jewellery.

They may get caught in moving parts. Rubber

gloves and non-slip shoes are recommended

when working outdoors. Wear a hair net if

you have long hair. Risk of injury!

•

Do not use the cable for purposes

other than that for which it is designed

Do not carry the compressor by its cable and

do not use the cable to pull the plug out of the

socket. Protect the cable from heat, oil and

sharp edges. The cable/plug could become

damaged.

•

Take care of your compressor

Keep your compressor clean in order to work

well and safely. Follow the maintenance inst-

ructions. Check the power plug and cable on

a regular basis and have them replaced by

an authorized specialist if they are damaged.

Check the extension cable regularly and re-

place it if damaged.

•

Pull out the power plug

When not in use and before carrying out any

maintenance work.

•

Avoid unintentional starting

Make sure that the switch is turned off when

connecting to the power supply.

•

When using an extension cable out-

doors

Check that it is approved for outdoor duty

and is marked accordingly.

•

Be alert at all times

Watch what you are doing. Use common sen-

se when working. Never use the compressor

when you are distracted.

•

Check your compressor for damage

Before using the compressor again, carefully

check the safety devices and any slightly da-

Anl_4010164.indb 8Anl_4010164.indb 8 25.03.13 15:5625.03.13 15:56

GB

- 9 -

maged parts to ensure that they are in good

working order. Check that the moving parts

are working correctly, that they do not jam,

and that no parts are damaged. Make sure

that all parts are fitted correctly to ensure that

the equipment remains safe to use. Unless

otherwise stated in the operating instructions,

damaged guards and parts have to be re-

paired or replaced by a customer service

workshop. Damaged switches have to be

replaced by a customer service workshop.

Never use an electric power tool with a switch

that cannot be turned on and off.

•

Important!

For your own safety you must only use the

accessories and additional units listed in the

operating instructions or recommended or

specified by the manufacturer. The use of

mounted tools or accessories other than those

recommended in the operating instructions

or catalog may place your personal safety

at risk.

•

Leave all repairs to a qualified electri-

cian

Repairs must be left strictly to qualified electri-

cians or the user might suffer an accident.

•

Noise

Wear ear muffs when you use the compressor.

•

Replacing the power cable

To prevent hazards, leave the replacement of

damaged power cables strictly to the manu-

facturer or a qualified electrician. There is a

risk of electric shock!

•

Inflating tires

Directly after inflating tires, check the pressure

with a suitable pressure gauge, for example

at your filling station.

•

Roadworthy compressors for building

site operations

Make sure that all lines and fittings are sui-

table for the maximum permissible operating

pressure of the compressor.

•

Place of installation

Set up the compressor on an even surface.

•

Make sure that all compressed air lines and

fittings are suitable for the maximum permissi-

ble operating pressure of the compressor.

•

For pressures above 7 bar it is recommended

to use an air line with a safety cable.

2.2 Safety instructions for working with

compressed air and blasting guns

•

The compressor pump and lines can become

very hot during operation. Touching these

parts will burn you.

•

The air which is sucked in by the compressor

must be kept free of impurities that could

cause fires or explosions in the compressor

pump.

•

When releasing the hose coupling, hold the

hose coupling piece with your hand. This way,

you can protect yourself against injury from

the rebounding hose.

•

Wear safety goggles when working with the

blow-out pistol. Foreign bodies or blown off

parts can easily cause injuries.

•

Do not blow at people with the blow-out

pistol and do not clean clothes while being

worn. Risk of injury!

2.3. Safety information for paint spray-

ing

•

Do not process any paints or solvents with a

flash point below 55° C. There is a risk of ex-

plosion!

•

Do not heat up paints or solvents. There is a

risk of explosion!

•

If hazardous liquids are processed, wear pro-

tective filter units (face guards). Also, adhere

to the safety information provided by the ma-

nufacturers of such liquids.

•

The details and designations of the Ordi-

nance on Hazardous Substances, which

are displayed on the outer packaging of the

processed material, must be observed. Addi-

tional protective measures are to be underta-

ken if necessary, particularly the wearing of

suitable clothing and masks.

•

Do not smoke during the spraying process

and/or in the work area. There is a risk of ex-

plosion! Paint vapors are easily combustible.

•

Never set up or operate the equipment in the

vicinity of a fire place, open lights or sparking

machines.

•

Do not store or eat food and drink in the work

area. Paint vapors are harmful to your health.

Anl_4010164.indb 9Anl_4010164.indb 9 25.03.13 15:5625.03.13 15:56

GB

- 10 -

•

The work area must exceed 30 m

3

and suf-

ficient ventilation must be ensured during

spraying and drying. Do not spray against the

wind. Always adhere to the regulations of the

local police authority when spraying combus-

tible or hazardous materials.

•

Do not process media such as white spirit,

butyl alcohol and methylene chloride with the

PVC pressure hose. These media will destroy

the pressure hose.

2.4 Operating pressure vessels

•

You must keep your pressure vessel in good

working order, operate the vessel correctly,

monitor the vessel, carry out necessary main-

tenance and repair work immediately and

meet the relevant safety precautions.

•

The supervisory authority may enforce essenti-

al control measures in individual cases.

•

A pressure vessel is not allowed to be used if

it has faults or deficiencies that can endanger

workers or third parties.

•

Check the pressure vessel for signs of rust

and damage each time before using. Do not

use the compressor with a damaged or rusty

pressure vessel. If you discover any damage,

then please contact the customer service

workshop.

Do not lose these safety instructions

3. Layout and items supplied

3.1 Layout

1. Transport handle

2. Pressure switch

3. Pressure regulator

4. Quick-lock coupling

(regulated compressed air)

5. Pressure gauge

(for reading the preset pressure)

6. Pressure gauge

(for reading the vessel pressure)

7. Pressure vessel

8. Supporting foot

9. Drain plug for condensed water

10. Axle screw

11. Wheel

12. Non-return valve with discharge line

13. Compressor pump

14. Housing

15. Air ﬁ lter

16. Oil sealing plug with oil dipstick

17. ON/OFF switch

18. Oil drainage screw

19. Safety valve

20. Quick-lock coupling

(unregulated compressed air)

21. Oil ﬁ ller opening

22. Washer

23. Spring washer

24. Nut

25. Screw

26. Washer

27. Washer

28. Nut

29. Wheel cap

3.2 Items supplied

•

Open the packaging and take out the equip-

ment with care.

•

Remove the packaging material and any

packaging and/or transportation braces (if

available).

•

Check to see if all items are supplied.

•

Inspect the equipment and accessories for

transport damage.

•

If possible, please keep the packaging until

the end of the guarantee period.

Important!

The equipment and packaging material

are not toys. Do not let children play with

plastic bags, foils or small parts. There is

a danger of swallowing or suffocating!

Anl_4010164.indb 10Anl_4010164.indb 10 25.03.13 15:5625.03.13 15:56

GB

- 11 -

4. Proper use

The compressor is designed to generate com-

pressed air for compressed-air driven tools which

can be driven with an air volume of up to approx.

360 l/min (e.g. a tire inﬂ ator, blow-out pistol and

paint spray gun). Compressed air tools with very

high air consumption have only limited suitability

for use with this compressor. For tools with high air

consumption (e.g. orbital sanders/grinders, rod

grinders, hammer screwdrivers), check whether

the compressor’s air output is sufﬁ cient to operate

the tool in question. The volume of air supplied by

the compressor must be greater than the volume

of air consumed by the compressed air tool at its

operating pressure.

The equipment is to be used only for its prescribed

purpose. Any other use is deemed to be a case of

misuse. The user / operator and not the manufac-

turer will be liable for any damage or injuries of

any kind caused as a result of this.

Please note that our equipment has not been de-

signed for use in commercial, trade or industrial

applications. Our warranty will be voided if the

machine is used in commercial, trade or industrial

businesses or for equivalent purposes.

5. Technical data

Mains connection: .........................230 V ~ 50 Hz

Motor rating kW: ................................S1 2400 W

..................................................S2 30 min 2600 W

Compressor speed min

-1

: .............................. 2850

Operating pressure bar: ..............................max. 8

Pressure vessel capacity (in liters): .....................50

Theoretical suction rate l/min.: .........approx. 360

Effective delivery rate at 7 bar: approx. 170 l/min

Sound power level L

WA

in dB: ............................96

K

WA

uncertainty: ...............................................2 dB

Sound pressure level L

pA

in dB: .......................... 74

K

pA

uncertainty: ................................................2 dB

Protection type: ................................................IP20

Weight of the unit in kg: ....................approx. 38.5

Oil (15W 40) ...................................................0.7 l

Load factor:

A load factor of S2 30 min (intermittent periodic

duty) means that you may operate the motor

continuously at its nominal power level (2600

W) for no longer than the time stipulated on the

speciﬁ cations label (30 min). If you fail to observe

this time limit the motor will overheat. During the

OFF period the motor will cool again to its starting

temperature.

The noise emission values were measured in ac-

cordance with EN ISO 2151: 2008.

Anl_4010164.indb 11Anl_4010164.indb 11 25.03.13 15:5625.03.13 15:56

GB

- 12 -

6. Before starting the

equipment

Before you connect the equipment to the mains

supply make sure that the data on the rating plate

are identical to the mains data.

•

Check the equipment for damage which may

have occurred in transit. Report any damage

immediately to the transport company which

was used to deliver the compressor.

•

Install the compressor near the point of con-

sumption.

•

Avoid long air lines and supply lines (extensi-

on cables).

•

Make sure that the intake air is dry and dust-

free.

•

Do not install the compressor in a damp or

wet room.

•

The compressor may only be used in suitable

rooms (with good ventilation and an ambient

temperature from +5 °C to 40 °C). There must

be no dust, acids, vapors, explosive gases or

inflammable gases in the room.

•

The compressor is designed to be used in dry

rooms. It is prohibited to use the compressor in

areas where work is conducted with sprayed

water.

•

The oil level in the compressor pump has to

be checked before putting the equipment into

operation (see 9.4).

7. Assembly and starting

 Important!

You must fully assemble the appliance

before using it for the ﬁ rst time!

You will require the following tools for assembly

and installation:

•

1 x open-ended wrench size 13 mm (not in-

cluded)

•

2 x open-ended wrench size 16 mm (not in-

cluded)

7.1 Fitting the wheels (11)

Fit the supplied wheels as shown in Figure 5.

7.2 Fitting the supporting feet (8)

Fit the supplied supporting feet as shown in

Figure 6.

7.3 Fitting the air ﬁ lters (15)

Remove the transportation stopper (B) and screw

the air ﬁ lters (15) securely to the equipment (Fig.

7, 8). Make sure that the intake opening on the air

ﬁ lter faces down.

7.4 Changing the transportation cover (A)

Remove the transportation cover from the oil ﬁ ller

opening (21) and insert the supplied oil sealing

plug (16) into the oil ﬁ ller opening. (Fig. 9, 10.)

7.5 Mains connection

•

Before you use the machine, make sure that

the mains voltage is the same as the operating

voltage (see the rating plate).

•

Long supply cables, extensions, cable reels

etc. cause a drop in voltage and can impede

motor start-up.

•

At low temperatures below +5°C, sluggish-

ness may make starting difficult or impossible.

7.6 ON/OFF switch (Fig. 2)

Pull the ON/OFF switch (17) upwards to switch

on the compressor. To switch off the compressor,

press the ON/OFF switch down.

7.7 Setting the pressure (Fig. 1-3)

•

Use the pressure regulator (3) to set the pres-

sure on the pressure gauge (5).

•

Turn the pressure regulator knob to adjust the

pressure.

•

The set pressure can be drawn from the quick-

lock coupling (4).

•

The vessel pressure can be read off the pres-

sure gauge (6).

•

The vessel pressure is drawn from the quick-

lock coupling (20).

Anl_4010164.indb 12Anl_4010164.indb 12 25.03.13 15:5625.03.13 15:56

GB

- 13 -

7.8 Setting the pressure switch (Fig. 1)

The pressure switch (2) is set at the factory.

Cut-in pressure approx. 6 bar

Cut-out pressure approx. 8 bar

7.9 Overload cut-out (Fig. 3)

The motor of this equipment is protected against

overload by an overload switch (G). If the rated

current is exceeded, the overload switch (G) will

shut down the equipment. After a short cooling

down period, the equipment can be switched on

again by pressing the overload switch (G).

8. Replacing the power cable

If the power cable for this equipment is damaged,

it must be replaced by the manufacturer or its

after-sales service or similarly trained personnel to

avoid danger.

9. Cleaning, maintenance,

storage, ordering spare

parts and transport

 Important!

Pull out the power plug before doing any

cleaning and maintenance work on the

equipment. Risk of injury from electric

shock!

 Important!

Wait until the equipment has cooled

down completely! Risk of burns!

 Important!

Always depressurize the equipment be-

fore carrying out any cleaning and main-

tenance work (see 9.7.1)! Risk of injury!

9.1 Cleaning

•

Keep the equipment free of dirt and dust as

far as possible. Wipe the equipment with a

clean cloth or blow it down with compressed

air at low pressure.

•

We recommend that you clean the equipment

immediately after you use it.

•

Clean the equipment regularly with a damp

cloth and some soft soap. Do not use cleaning

agents or solvents; these may be aggressive

to the plastic parts in the equipment. Ensure

that no water can get into the interior of the

equipment.

•

You must disconnect the hose and any

spraying tools from the compressor before

cleaning. Do not clean the compressor with

water, solvents or the like.

9.2 Maintenance work on the pressure

vessel (Figure 1)

Important! To ensure a long service life of the

pressure vessel (7), drain off the condensed water

by opening the drain valve (9) each time after

using. Release the vessel pressure ﬁ rst (see 9.7.1).

Open the drain screw by turning counter-clock-

wise (looking at the screw from the bottom of the

compressor) so that all the condensed water can

run out of the pressure vessel. Then close the drain

screw again (turn it clockwise). Check the pressure

vessel for signs of rust and damage each time

before using. Do not use the compressor with a

damaged or rusty pressure vessel. If you discover

any damage, then please contact the customer

service workshop.

 Important!

The condensed water from the pressure

vessel will contain residual oil. Dispose

of the condensed water in an environ-

mentally compatible manner at a suitable

collection point.

Anl_4010164.indb 13Anl_4010164.indb 13 25.03.13 15:5625.03.13 15:56

GB

- 14 -

9.3 Safety valve (Figure 2)

The safety valve (19) has been set for the highest

permitted pressure of the pressure vessel. It is

prohibited to adjust the safety valve or remove its

seal. Actuate the safety valve from time to time to

ensure that it works when required. Pull the ring

with sufﬁ cient force until you can hear the com-

pressed air being released. Then release the ring

again.

9.4 Checking the oil level at regular inter-

vals (Figure 11)

Place the compressor on a level and straight

surface. The oil level must be between the two

marks MAX and MIN on the oil dipstick (16). Oil

change: we recommend SAE 15W 40 or equiva-

lent. The original oil ﬁ lling must be changed after

100 hours in operation; thereafter the oil must be

drained and replaced with new oil after every

300 hours in operation.

9.5 Changing the oil (Figure 1,10, 11)

Switch off the motor and pull the mains plug out

of the socket. After releasing any air pressure (see

9.7.1) you can unscrew the oil drain screw (18)

from the compressor pump (13). To prevent the oil

from running out in an uncontrolled manner, hold

a small metal chute under the opening and collect

the oil in a container. If the oil does not drain out

completely, we recommend tilting the compressor

slightly. When the oil has drained out, reﬁ t the oil

drain screw (18).

Dispose of the old oil at a drop-off point

for old oil.

To ﬁ ll in the correct quantity of oil, make sure that

the compressor stands on an even surface. Fill

new oil through the oil ﬁ ller opening (21) until it

comes up to the maximum level. Check the oil

level by inserting the dipstick. Do not exceed

the maximum ﬁ lling quantity. Overﬁ lling the

equipment may result in damage. Reinsert the oil

sealing plug (16) into the oil ﬁ ller opening (21).

9.6 Cleaning the intake ﬁ lter

(Fig. 2, 3, 12)

The intake ﬁ lters (15) prevent the drawing in

of dust and dirt. It is essential to clean these

ﬁ lters after at least every 300 hours in opera-

tion. A clogged intake ﬁ lter will decrease the

compressor’s performance dramatically.

Remove the intake ﬁ lters from the equipment by

unscrewing them. The ﬁ lter housing (D) is plugged

on the ﬁ lter cover (C) and can be removed by ap-

plying slight pressure to the ﬁ lter cover. Carefully

tap out the air ﬁ lters (F), the ﬁ lter cover and the

ﬁ lter housing. Then blow out these parts with com-

pressed air (approx. 3 bar) and reinstall in reverse

order. The ﬁ lter cover and the ﬁ lter housing have

different latching positions. When you assemble

the intake ﬁ lter, make sure that the intake opening

faces down.

9.7 Storage

 Important!

Pull out the mains plug and ventilate the

equipment and all connected pneumatic

tools (see 9.7.1). Switch off the compres-

sor and make sure that it is secured in

such a way that it cannot be started up

again by any unauthorized person.

 Important!

Store the compressor only in a dry lo-

cation which is not accessible to unau-

thorized persons. Always store upright,

never tilted! Oil may leak out!

9.7.1 Releasing excess pressure

Release the excess pressure by switching off the

compressor and using the compressed air which

is still left in the pressure vessel, e.g. with a com-

pressed air tool running in idle mode or with a

blow-out pistol.

Anl_4010164.indb 14Anl_4010164.indb 14 25.03.13 15:5625.03.13 15:56

GB

- 15 -

9.8 Ordering replacement parts:

Please quote the following data when ordering

replacement parts:

•

Type of machine

•

Article number of the machine

•

Identification number of the machine

For our latest prices and information please go to

www.isc-gmbh.info

9.9 Transport (Figure 1)

•

Switch off the equipment and pull out the

power plug before lifting and moving the

compressor.

•

Use the transport handle (1) to move the com-

pressor.

•

Use the transport handle (1) on the pressure

vessel (7) to lift the compressor. Note the

equipment‘s weight!

•

Transport the compressor only in an upright

position and secure it against tilting so that no

oil runs out.

•

Secure the compressor in accordance with the

regulations in force for transporting equipment

in motor vehicles.

10. Disposal and recycling

The unit is supplied in packaging to prevent its

being damaged in transit. This packaging is raw

material and can therefore be reused or can be

returned to the raw material system.

The unit and its accessories are made of various

types of material, such as metal and plastic. De-

fective components must be disposed of as spe-

cial waste. Ask your dealer or your local council.

For EU countries only

Never place any electric power tools in your

household refuse.

To comply with European Directive 2002/96/EC

concerning old electric and electronic equipment

and its implementation in national laws, old elec-

tric power tools have to be separated from other

waste and disposed of in an environment-friendly

fashion, e.g. by taking to a recycling depot.

Recycling alternative to the return request:

As an alternative to returning the equipment to the

manufacturer, the owner of the electrical equip-

ment must make sure that the equipment is proper-

ly disposed of if he no longer wants to keep the

equipment. The old equipment can be returned to

a suitable collection point that will dispose of the

equipment in accordance with the national recyc-

ling and waste disposal regulations. This does not

apply to any accessories or aids without electrical

components supplied with the old equipment.

Anl_4010164.indb 15Anl_4010164.indb 15 25.03.13 15:5625.03.13 15:56

GB

- 16 -

11. Possible causes of failure

Problem Cause Solution

The compressor

does not start.

1. No supply voltage.

2. Insufﬁ cient supply voltage.

3. Outside temperature is too low.

4. Motor is overheated.

1. Check the supply voltage, the pow-

er plug and the socket-outlet.

2. Make sure that the extension cable

is not too long. Use an extension

cable with large enough wires.

3. Never operate with an outside tem-

perature of below +5° C.

4. Allow the motor to cool down. If

necessary, remedy the cause of the

overheating.

The compressor

starts but there is no

pressure.

1. The non-return valve leaks.

2. The seals are damaged.

3. The drain plug for condensation

water (9) leaks.

1. Have a service center replace the

non-return valve.

2. Check the seals and have any da-

maged seals replaced by a service

center.

3. Tighten the screw by hand. Check

the seal on the screw and replace if

necessary.

The compressor

starts, pressure is

shown on the pres-

sure gauge, but the

tools do not start.

1. The hose connections have a leak.

2. A quick-lock coupling (4, 20) has

a leak.

3. Insufﬁ cient pressure set on the pres-

sure regulator (3).

1. Check the compressed air hose and

tools and replace if necessary.

2. Check the quick-lock coupling and

replace if necessary.

3. Increase the set pressure with the

pressure regulator.

Anl_4010164.indb 16Anl_4010164.indb 16 25.03.13 15:5625.03.13 15:56

GB

- 17 -

12. Declaration of conformity

Yu Feng Quing/Product-ManagementWeichselgartner/General-Manager

D erklärt folgende Konformität gemäß EU-Richtlinie und

Normen für Artikel

GB explains the following conformity according to EU directi-

ves and norms for the following product

F déclare la conformité suivante selon la directive CE et les

normes concernant l’article

I dichiara la seguente conformità secondo la direttiva UE e

le norme per l’articolo

NL verklaart de volgende overeenstemming conform EU

richtlijn en normen voor het product

E declara la siguiente conformidad a tenor de la directiva y

normas de la UE para el artículo

P declara a seguinte conformidade, de acordo com a

directiva CE e normas para o artigo

DK attesterer følgende overensstemmelse i medfør af

EU-direktiv samt standarder for artikel

S förklarar följande överensstämmelse enl. EU-direktiv och

standarder för artikeln

FIN vakuuttaa, että tuote täyttää EU-direktiivin ja standardien

vaatimukset

EE tõendab toote vastavust EL direktiivile ja standarditele

CZ vydává následující prohlášení o shodě podle směrnice EU

a norem pro výrobek

SLO potrjuje sledečo skladnost s smernico EU in standardi za

izdelek

SK vydáva nasledujúce prehlásenie o zhode podľa smernice

EÚ a noriem pre výrobok

H a cikkekhez az EU-irányvonal és Normák szerint a

következő konformitást jelenti ki

PL deklaruje zgodność wymienionego poniżej artykułu z

następującymi normami na podstawie dyrektywy WE.

BG декларира съответното съответствие съгласно

Директива на ЕС и норми за артикул

LV paskaidro šādu atbilstību ES direktīvai un standartiem

LT apibūdina šį atitikimą EU reikalavimams ir prekės normoms

RO declară următoarea conformitate conform directivei UE şi

normelor pentru articolul

GR δηλώνει την ακόλουθη συμμόρφωση σύμφωνα με την

Οδηγία ΕΚ και τα πρότυπα για το προϊόν

HR potvrđuje sljedeću usklađenost prema smjernicama EU i

normama za artikl

Izjava o sukladnosti za ovaj proizvod dostupna je na

internet stranici www.lidl.hr.

BIH potvrđuje sljedeću usklađenost prema smjernicama EU i

normama za artikl

RS potvrđuje sledeću usklađenost prema smernicama EZ i

normama za artikal

RUS следующим удостоверяется, что следующие продукты

соответствуют директивам и нормам ЕС

UKR проголошує про зазначену нижче відповідність виробу

директивам та стандартам ЄС на виріб

MK ја изјавува следната сообрзност согласно

ЕУ-директивата и нормите за артикли

TR Ürünü ile ilgili AB direktiﬂ eri ve normları gereğince aşağıda

açıklanan uygunluğu belirtir

N erklærer følgende samsvar i henhold til EU-direktivet og

standarder for artikkel

IS Lýsir uppfyllingu EU-reglna og annarra staðla vöru

Konformitätserklärung

Kompressor PKO 400 B2 (Parkside)

X

87/404/EC_2009/105/EC

2005/32/EC_2009/125/EC

2006/95/EC

2006/28/EC

X

2004/108/EC

2004/22/EC

1999/5/EC

X

97/23/EC

90/396/EC_2009/142/EC

89/686/EC_96/58/EC

X

2011/65/EC

X

2006/42/EC

Annex IV

Notiﬁ ed Body:

Notiﬁ ed Body No.:

Reg. No.:

2000/14/EC_2005/88/EC

Annex V

Annex VI

Noise measured: L

WA

= dB (A); guaranteed L

WA

= dB (A)

P = KW; L/Ø = cm

Notiﬁ ed Body:

2004/26/EC

Emission No.:

Standard references: EN 1012-1; EN 60204-1;

EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-11

Landau/Isar, den 25.03.2013

First CE: 13 Archive-File/Record: NAPR007418

Art.-No.: 40.101.64 I.-No.: 11013 Documents registrar: Siegfried Roider

Subject to change without notice Wiesenweg 22, D-94405 Landau/Isar

Einhell Germany AG · Wiesenweg 22 · D-94405 Landau/Isar

Anl_4010164.indb 17Anl_4010164.indb 17 25.03.13 15:5625.03.13 15:56

GB

13. Warrant y certiﬁ cate

Dear Customer,

All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event

that your device develops a fault, please contact our service department at the address shown on this guarantee card.

Of course, if you would prefer to call us then we are also happy to offer our assistance under the service number prin-

ted below. Please note the following terms under which guarantee claims can be made:

1. These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights. We do

not charge you for this guarantee.

2. Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the rec-

tiﬁ cation of these defects or replacement of the device. Please note that our devices have not been designed for

use in commercial, trade or industrial applications. Consequently, the guarantee is invalidated if the equipment

is used in commercial, trade or industrial applications or for other equivalent activities. The following are also

excluded from our guarantee: compensation for transport damage, damage caused by failure to comply with

the installation/assembly instructions or damage caused by unprofessional installation, failure to comply with the

operating instructions (e.g. connection to the wrong mains voltage or current type), misuse or inappropriate use

(such as overloading of the device or use of non-approved tools or accessories), failure to comply with the main-

tenance and safety regulations, ingress of foreign bodies into the device (e.g. sand, stones or dust), effects of

force or external inﬂ uences (e.g. damage caused by the device being dropped) and normal wear resulting from

proper operation of the device. This applies in particular to rechargeable batteries for which we nevertheless

issue a guarantee period of 12 months. The guarantee is rendered null and void if any attempt is made to tamper

with the device.

3. The guarantee is valid for a period of 3 years starting from the purchase date of the device. Guarantee claims

should be submitted before the end of the guarantee period within two weeks of the defect being noticed. No

guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains

applicable to the device even if repairs are carried out or parts are replaced. In such cases, the work performed

or parts ﬁ tted will not result in an extension of the guarantee period, and no new guarantee will become active

for the work performed or parts ﬁ tted. This also applies when an on-site service is used.

4. In order to assert your guarantee claim, please send your defective device postage-free to the address shown

below. Please enclose either the original or a copy of your sales receipt or another dated proof of purchase.

Please keep your sales receipt in a safe place, as it is your proof of purchase. It would help us if you could de-

scribe the nature of the problem in as much detail as possible. If the defect is covered by our guarantee then your

device will either be repaired immediately and returned to you, or we will send you a new device.

Of course, we are also happy offer a chargeable repair service for any defects which are not covered by the scope

of this guarantee or for units which are no longer covered. To take advantage of this service, please send the device

to our service address.

- 18 -

IAN 89566

Anl_4010164.indb 18Anl_4010164.indb 18 25.03.13 15:5625.03.13 15:56

CZ

- 19 -

Obsah

Patisk nebo jiné rozmnožování dokumentace a průvodních listin, také ve výtažcích, je přípustný pouze s

výslovným souhlasem ﬁ rmy iSC GmbH.

Technické změny vyhrazeny

1. Úvod .......................................................................................................................................................... 21

2. Bezpečnostní pokyny................................................................................................................................ 21

3. Popis přístroje a rozsah dodávky ............................................................................................................23

4. Použití podle účelu určení ........................................................................................................................24

5. Technická data ..........................................................................................................................................24

6. Před uvedením do provozu ......................................................................................................................25

7. Montáž a uvedení do provozu ................................................................................................................25

8. Výměna síťového napájecího vedení ......................................................................................................26

9. Čištění, údržba, uložení, objednání náhradních dílů a transport .........................................................26

10. Likvidace a recyklace ...............................................................................................................................28

11. Možné příčiny výpadku ...........................................................................................................................29

12. Prohlášení o shodě ....................................................................................................................................30

13. Záruční list ................................................................................................................................................. 31

Anl_4010164.indb 19Anl_4010164.indb 19 25.03.13 15:5625.03.13 15:56