2. Creality
  3. CV-Laser
CV-Laser

Creality CV-Laser Používateľská príručka

  • Dobrý deň! Prečítal som si používateľskú príručku k laserovému modulu Creality CV-Laser Module. Som pripravený odpovedať na vaše otázky týkajúce sa inštalácie, používania a údržby zariadenia. Príručka obsahuje podrobné pokyny na gravírovanie, bezpečnostné opatrenia a riešenie problémov.
  • Aké materiály môžem gravírovať s týmto modulom?
    Ako nastavím zaostrenie lasera?
    Čo mám robiť, ak sa počas gravírovania vyskytne problém?
    Aká je prevádzková teplota laserového modulu?
CV-Laser Module
User Manual • Uživatelský manuál •
Užívateľský manuál • Használati utasítás •
Benutzerhandbuch
2
English
3 – 24
Čeština
25 – 46
Slovenčina
47 – 68
Magyar
69 – 90
Deutsch
91 – 112
3
Dear customer,
Thank you for purchasing our product. Please read the following instructions carefully
before first use and keep this user manual for future reference. Pay particular attention
to the safety instructions. If you have any questions or comments about the device,
please contact the customer line.
󱭼󱭽󱭾󱭿󱮀 www.alza.co.uk/kontakt
✆ +44 (0)203 514 4411
Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Prague 7, www.alza.cz
4
Dear Consumers
Thank you for choosing our products. For the best experience, please read the
instructions before operating the product. Our team will always be ready to render you
the best service. Please contact us via the phone number or e-mail address provided at
the end when you encounter any problem.
Visit out official website www.creality.com to find relevant software/hardware
information, contact details and operation and maintenance instructions.
Notes
Using the hight-density laser beam to heat up the workpiece surface when engraving or
cutting aims to gasify without combustion. While most workpieces are essentially
combustible, which may be ignited, leading to open fire and consequently to the
machine breakdown and environment contamination. Please follow the following
operating principles.
1. It is prohibited to store the machine in areas close to combustible and explosive
substances, volatile solvents, or source of heat. Instead, store in a well-ventilated,
cool, and dust-free place.
2. Make sure that only the specific attached power cord rather than other similar
power cords are used during installation.
3. Do regular maintenance. Clean the product with a dry cloth when the power is
turned off, wiping away dust and foreign matter.
4. Ensure to turn the laser at 0°C-35°C. Operation at sub-zero temperature is
prohibited.
5. Switch off the machine if it is offline for an extended period of time and unplug
the power cord. It is prohibited to run the machine under wet environment or in
thunderstorm weather.
6. It is prohibited to come in contact with electronic areas with hands or other tools
when the machine is connected to power supply.
7. Touching any moving parts and laser module while the machine is running is
prohibited.
8. Wear goggles to prevent vision damage arising from exposure to the laser spot
during laser engraving operation.
9. It is advisable to run the machine under well ventilated condition at laser
engraving may generate small amount of fume or gas.
10. Children under 10 years old are not allowed to run the machine without adult
presence, which otherwise may lead to personal injury.
11. Put in place fire extinguishers in case of use, which shall be regularly checked. It
is prohibited to keep the machine unattended while it is running.
5
12. Users should comply with the laws and regulations of the corresponding
countries and regions where the equipment is located (used), abide by
professional ethics, pay attention to safety obligations, and strictly prohibit the
use of out products or equipment for any illegal purposes. Creality will not be
responsible for any violators’ legal liability under any circumstance.
Introduction
1. Eye protect exhaust hood
2. Laser head
3. Head screw
4. Focusing bar
5. Activated carbon smoking adsorption cotton
6. Axial fan
6
Equipment Parameters
1.6W
5W
Name
Laser Module
Model
CV-Laser Module
Size
185mm x 180mm x 85mm
Net Weight
400g
460g
Gross Weight
540g
600g
Power Supply
24V DC
Laser Source
Semiconductor laser unit
Lase wave length
450±5nm
455±nm
Lase power
1.6W
5W
Safety Class
Class IV (FDA classification standard)
Range of operation
temperature
0°C-35°C
Support materials
Cardboard, wood, bamboo, rubber, leather, fabric,
acrylic, plastic, etc.
Package Content
Laser Module x 1
Laser module wire x 1
Wood plate x 2
Brown paper x 2
Colour asphalt felt
paper x 7
M2 Socket head
wrench x 1
Soft magnetic strip x
2
Hexagon socket
Activated smoking-
adsorption cotton
x 2
Safety goggles x 1
Dustless cloth x 1
Instruction manual x
1
7
Assembling
1. Take the printer Ender-3 S1 as an example
Remove the hotend kit
Please make sure that before removing the hotend kit, you should firstly take off
the print material from the nozzle while it is heated. Disconnect the power and
allow it to cool to room temperature. Unplug the cable and loosen the four
screws to remove the hotend kit.
Unplug the flat
cable
Loosen the four screws
8
2. Install the laser head fixing plate
Take out the laser head fixing plate and the two Hexagon socket countersunk
head screw from the box, attach the fixing plate to the machine and tighten the
two countersunk screws using and Allen key (clockwise).
3. Installing the Laser Module
Take out the Laser Module and hand screw from the box, attach the Laser
Module to the fixing plate and tighten it using the hand screw (clockwise
direction)
Laser head
fixing plate x 1
Hexagon socket
countersunk head
screw x 2
M2 Socket head
wrench x 1
Laser Module
Hexagon
socket
9
4. One side of the laser module cable plugs into the machine’s expansion port and
the other side into the laser head.
Note: Installation and removal must be carried out in a power-off state, to avoid the risk
of burning out the motherboard.
Laser
Module
10
Firmware update
When using the laser module on the Ender-3 S1 for the first time, please check if the
motherboard firmware and the screen firmware are the applicable version respectively.
The method is as follows.
Connect the machine to the power supply, turn on the power switch on the side, select
“Control” - “Info”, the firmware version number should be V1.0.4 or above.
Otherwise, please download the latest version from the website link and update the
firmware of motherboard and screen: https://www.creality.com/download -> Accessory
Firmware -> CV-Laser Module Firmware
11
Motherboard firmware
Decompress the UPDATE.rar and copy it to SD card:
Insert the SD card into the machine and turn on the power to update automatically.
Screen firmware
Copy the private file to the TF card:
1. Unplug the screen cable and then remove the screen from the screen holder.
2. Use and Allen key to unscrew the four screws on the back of the screen and
remove the lower cover of the screen.
3. Insert TF card into the TF card slot of the motherboard, plug in the screen cable
and power on to update automatically.
4. After the update is complete, power off, remove TF card, reinstall the screen and
restart the machine.
Screen cable
terminals
M2 Sokcet head
wrench
TF card x 1 (Self-
Provided)
The screen holder
Four screws
12
Software installation
Please visit the following weblink Creality_Print: https://www.creality.com/download
Creality_Print either Windows or Mac system, please choose the right software version
when download.
1. Double click to open the software installation package, click “Next” – “Accept”.
2. Confirm the installation location of the software, click “Browse…” - “Next” –
“Install” (not recommended to install on C drive) – “Finish”
13
Software Intro
Open the Creality_Print software and click on the navigation button at the top right to
see the basic features.
14
Software usage
1. Add a printer
Take the Ender-3 S1 Laser as an example, click on the locations as shown to add
your machine to turn.
2. Make sure the current status is “Laser”
15
3. Click on the “Picture” button on the left and find the image file you need to
engrave. Open to import the picture into the CrealityPrint software.
16
4. Adjust the position, size, rotation angle and other parameters of the file in the
right-hand console, setting the processing mode and working parameters, finally
preview the processing effect of it.
5. Finally, click on “Generate G-Code” to save the engraving file on the SD card.
17
Engraving
1. Insert the SD card into the machine and turn on the power switch on the side.
2. After the machine is switched on, if you are using it for the first time, please
select laser engrave.
18
To switch from fusing to laser engrave, select “Control” – “Switched Laser engraving”.
The software pops up the following prompt box. Please ensure that the laser module is
installed correctly (note that the laser module must be installed and removed only when
the power is off) and select “Confirm”.
19
3. Please place the engraving material under the laser head, counter-clockwise push
the fixed focus bar, adjust the laser focus to the appropriate value through the
knob (different thickness of the material corresponding to different values), until
the focusing bar touches the engraved material surface when natural vertical
down. Finally, clockwise push the focusing bar until it is attached by the magnet,
then select “Finish”.
4. Return to the main interface, select “Auto Home”, wait for the machine back to
zero completed.
20
5. Select “Engrave” and press the knob to confirm.
Select “Run Range”, the laser head will move repeatedly around the maximum X and Y
edges. You can adjust the engraving material to the right position.
/