ALZA Totem TS2 Používateľská príručka

Laser Engraver TS2

User Manual • Uživatelský manuál •

Užívateľský manuál • Használati utasítás •

Benutzerhandbuch

2

English

3 – 28

Čeština

29 – 54

Slovenčina

55 – 80

Magyar

81 – 106

Deutsch

107 – 132

3

Dear customer,

Thank you for purchasing our product. Please read the following instructions carefully

before first use and keep this user manual for future reference. Pay particular attention

to the safety instructions. If you have any questions or comments about the device,

please contact the customer line.

✉ www.alza.co.uk/kontakt

✆ +44 (0)203 514 4411

Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Praha 7, www.alza.cz

4

Letter from TWOTREES

Dear consumers,

Thank you for choosing us.

It’s customer-oriented idea, continuous innovation and pursuit of excellence that enable

very-body to have wonderful experience in using process. We believe that this manual

will be helpful. Hope you enjoy the good time with TwoTrees.

If you have any problems, please feel free to contact us via:

Website: www.twotrees3d.com

Facebook: https://www.facebook.com/group/twotrees3Dprinter

For general inquiry: info@twotrees3d.com

For technical support: service@twotrees3d.com

We will contact you within 24 hours.

Sincerely yours,

TwoTrees Team

Precautions

Please follow the instructions, due to misuse will be at your own risk.

1. Avoid looking steadily at the laser, which may damage your eyes.

2. Avoid touching directly during the machine working.

3. You can place a metal plate under the engraved or cut object to prevent your

table being burned through.

4. Avoid combustible object or gas.

5. Keep it away from children or pregnant women.

6. Do not take apart the laser without instructions.

7. Do not use it on material that reflects the light.

8. Wear goggles while taking off the laser cover.

9. Turn off the power when not use.

5

Safety guidelines

Warning: Laser engraving machine cannot directly carve or cut material that reflects the

light, may cause injury.

The product has a high engraving speed and is not recommended for industrial cutting.

And the laser head is a consumable.

Do not operate the laser head directly with your hands. Please wear goggles.

The laser diode is a sensitive component, please prevent static damage. (This product

has an electrostatic protection design, but there is still a possibility of damage.)

About your machine

1) X-axis Stepper Motor

2) Z-axis Stepper Motor

3) Laser Module

4) Control Box

5) Flash Buzzer

6) Emergency Stop Button

7) Z-axis Focusing Probe

8) X-axis Tensioner

9) Y-axis Stepper Motor

1) Y-axis Tensioner

2) X-axis Drag Chain

3) Y-axis Endstop/Limit Switch

4) Z-axis Manual Focusing Lifter Knob

5) X-axis Endstop/Limit Switch

6) Y-axis Drag Chain

7) Flame Detector Module

8) Y-axis lead rod

6

Part list

Front Frame X1

Y-axis Left Frame X1

Y-axis Right Frame X1

Back Frame X1

X-axis Stepper Motor X1

X-axis Crossbeam X1

Laser Module X1

X-axis drag chain X1

Screw Bolt M5*25 X6

Screw Bolt M5*40 X2

Screw Bolt M4*16 X5

Screw M3*6 X4

Screw M3*4 X4

Screw Bolt M3*6 X14

Y-axis Drag Chain Holder X1

Screw Bolt M5*20 X1

Tool Package X1

Data Cable X1

Power Adapter X1

Power Cable X1

7

Main parameters

Machine Size:

733 x 721 x 172 mm

Machine Weight:

8 kg

Engraving Size:

450 x 450 mm

Laser Wavelength:

445±5 mm

Engraving Accuracy:

0.1 mm

Engraving Speed:

10 000 mm/min

Software Support System:

Mac, windows

Material:

Aluminium profile + Sheet metal parts

Electrical Requirement:

24 V 4 A DC

Motherboard:

DLC ESP32 Motherboard (32bit)

Laser Power:

10 000 mw

File Format:

NC, BMP, JPG, PNG, GCODE, ETC

Supported Software:

LaserGRBL (Windows), Lightburn (Common)

Power Type:

USA/EU Plug (Optional)

Software Support Languages:

Chinese, English, Italian, French, German

Working Environment:

RHTemperature 5-40˚C, Humidity 20-60 % RH

Engraving Method:

USB connection/APP/Wireless computer WEB

terminal/Screen (optional)

Engraving Materials:

Wood, Plastic, Paper, Leather, Bamboo, Sponge

Paper, Alumina, Stainless Steel, Chevron, Acrylic,

Glass, etc.

Engraving Mode:

Image carving/Text carving/Scanning

carving/Contour carving/Pixel carving

8

Assembly

1.1 Install the Frames

Installation of Front Frame, Back Frame and Y-axis Left Frame

Front Frame x 1

Back Frame x 1

Y-axis Left Frame x 1

M5*25 Screw Bolt x 3

Please mind the buckle position of frame.

NOTE: Please set the Timing belt into Pulley groove and profile into buckle position

before tightening the screw bolts.

1.2 Installation of Y-axis Left Frame Timing belt & Idler Pulley

M4*16 Screw Bolt x 2

NOTE: Please set the Timing belt into Pulley groove before installing the Idler Pulley.

Synchronous wheel

Idler Pulley

9

1.3 Y-axis Left Tensioner adjustment

Please tighten tensioner screw in clockwise direction with hex key or loosen the belt in

counterclockwise direction.

NOTE: If tensioner too tight, Pulley would stuck. And if too loose, it would also affect

engraving result.

1.4 Installation of Y-axis Right Frame

Y-axis Right Frame Parts x 1

Screw Bolt M5*25 x 3

10

1.5 Installation of Y-axis Right Timing belt & Idler Pulley

Screw Bolt M4*16 x 2

NOTE: Please set the Timing belt into Pulley groove before installing the Idler Pulley

1.6 Adjustment of Y-axis Right Tensioner

Please tighten tensioner screw in clockwise direction with hex key or loosen the belt in

counterclockwise direction.

NOTE: If tensioner too tight, Pulley would stuck. And if too loose, it would also affect

engraving result.

2.1 Installation of X-axis Crossbeam Parts

X-axis Crossbeam Parts x 1

M5*40 Screw x 2

M5*20 Screw x 1

M4*16 Screw x 1

11

Attention: Please make sure the X-axis crossbeam is parallel to front crossbeam (check

ruler marks on both sides as reference) while installation, otherwise it would affect

movement of Y-axis and engraving affects.

2.2 Installation of Laser Module

Laser Module x 1

M3*6 Screws x 4

2.3 Installation of Protective Cover

Laser Protective Cove x 1

M3*8 Screws x 2

3.1 Installation of X-axis drag chain

M3*6 Screws x 4

X-axis Cable Carriage Parts x 1

Front beam profile

12

4.1 Installation of Y-axis drag chain

Installation of Y-axis drag chain parts

Y-axis drag chain holder x 1

M3*4 Screw x 2

4.2 Installation of drag chain

Y-axis drag chain parts

M3*6 Screw x 2

M4*10 Screw x 2

13

5. Installation of X-axis Stepper Motor

M3*6 Screw x 4

X-axis Stepper Motor x 1

NOTE:

1) Please put timing belt into Pulley groove on Stepper Motor.

2) Please make sure the circuit connector in the right direction as above picture.

6. Adjustment of X-axis Tensioner

NOTE: Please make sure the Timing belt is tight to avoid engraving dislocation.

X-axis Stepper Motor

14

Wiring instruction

1. Cable marking explanation

X-axis Endstop Switch Cable

X (4PIN) → X-axis Stepper Motor Cable

Y (3PIN) → Y-axis Endstop Switch Cable

Y (4PIN) → Y-axis Stepper Motor Cable

Z (2PIN) → Z-axis Endstop Switch Cable

Z (4PIN) → Z-axis Stepper Motor Cable

A (2PIN) → Laser Signal Cable

E (3PIN) → Flame Detector Signal Cable

1 (2PIN) → Laser Fan Line

NOTE: PIN refer to the quantity of cable connecting pins.

2. Wiring diagram

X (4PIN) → X-axis

Stepper Motor Cable

X (3PIN) → X-axis

Endstop Switch Cable

Z (4PIN) → Z-axis

Stepper Motor Cable

Y (4PIN) → Y-axis

Stepper Motor Cable

Z (2PIN) → Z-axis

Endstop Switch Cable

1 (2PIN) → Laser

Fan Line

A (2PIN) → Laser

Signal Cable

E (3PIN) → Flame

Detector Signal Cable

Attention: Please make sure all wiring corrects before turning on the machine.

15

GRBL beginner’s guide

1. Software downloading

LaserGRBL is one of the most popular DIY laser engraving software, which can be

downloaded in LaserGRBL website http://lasergrbl.com/download/ (the installation

package is also available on the TF card from the manufacturer or USB flash disk).

2. Software installation

Double click the software installation package to start the software installation and click

“Next” until the installation is complete.

3. Language

Click “Language” on the menu at the top to select the language you need.

4. Load Engraving File

Click “File” and “Open File” in turn, as shown in figure 8.1, and then select the graph you

want to engrave.

LaserGRBL supports files in the formats of NC, BMP, JPG, PNG, etc.

16

5. Set picture parameters, engraving mode, and engraving quality

1) LaserGRBL can adjust the sharpness, brightness, contrast, highlight and other

properties of the target graph. We can preview window affect during adjustment

and adjust the affect to your satisfaction.

2) In the engraving mode, “Line-to-line Tracking” and “1Bit Shaking” can usually be

chosen, “1Bit Shaking” is more suitable for carving grayscale graph. Please choose

“Vector Diagram” or “Center Line” if you need cutting.

3) Engraving quality essentially refers to the line width of laser scanning. This

parameter mainly depends on the size of the laser spot of the engraving machine.

NOTE: The recommended engraving quality range is 12-15. Different materials

have different reactions to laser irradiation, so the specific value depends on the

specific engraving material.

4) At the bottom of the preview window, the graph can also be rotated, mirrored, cut

and so on. After completing the above setting, click next to enter the setting of

engraving speed, engraving energy, and engraving size.

6. Set engraving speed, engraving energy, and engraving size

1) The recommended engraving speed is 1 000, which is a relative appropriate value

after repeated experiments. Of course, you can increase or decrease this speed

according to your preference. A faster engraving speed will save time but lead to the

decline in the engraving effect. Slower speed is the opposite.

2) In laser mode, there are two instructions: M3 and M4 instruction is recommended

for engraving in “1bit jitter” mode, and M3 instruction is recommended for other

cases. If you have only M3 instruction on the laser, please check whether the laser

mode is used in the GRBL configuration. Please refer to the official instructions of

LaserGRBL for GRBL configuration.

Colour adjustment,

intensity adjustment

Choose engraving mode

Quality: 12-15 (recommended)

Direction adjustment

pattern cutting

17

3) Choice of engraving energy. Choose it according to different materials.

4) Finally, set the size and click the “Create” button to complete the setting of

all engraving parameters.

Save GCODE file

Click “File” in the menu at the top of the software interface, enter the drop-down menu,

and select “Save”. Copy the saved .nc file to the TF card and insert the TF card into the

engraver to use the file to engrave your work.

Use the “MKSLaserTool” software in TF to add preview codes to GCODE files.

Connect PC

1. Connect the machine with the computer installed with LaserGRBL software

with USB data cable.

2. Plug in the power.

3. Open LaserGRBL on the computer.

4. Select the specific port number and baud rate – 115 200 (Figure A.10).

5. Click the lightning sign. When the lightning sign changes to the red “X” and the

direction sign is lit, it indicated that the connection is successful (Figure A.11).

Generally, the COM port does not need to be selected manually, unless multiple serial

port devices are connected to the computer, you can find the port of the machine in the

device manager of the windows system (as shown in Figure A.09). A simpler way is to try

the displayed port number one by one.

The default engraving speed is 1000

and can be adjusted as required

Set the energy value. Improper energy

will affect the engraving effect

Enter the size of the graph you

want to engrave

18

NOTE: If you cannot find the correct port in the “Ports”, you may need to:

Method 1: Click “Tools” in the menu to install CH340 driver (The function is not available

in some software versions),

Method 2: Copy the “CH340ser.exe” file in the TF Card (USB flash disk) to the computer

and install it.

1) After the laser head has been used for a period of time, it is necessary to clean the

lens of the light outlet under the laser head to ensure normal cutting ability.

2) Wiping the lens must be done after the machine is powered off, otherwise the laser

will hurt people.

3) After wiping the lens, please dry it naturally for about 3-5 minutes and wait for the

lens to dry before powering it on, otherwise the light will cause the lens to break.

4) You can watch the video tutorial by scanning the QR code of the manual.

Reference of materials

For engraving:

Material

Speed (mm/min)

Power (%)

Times

Plywood

6000

50

1

Acrylic

6000

20

1

Leather

6000

20

1

Electroplated coating

1000

100

1

Powder coating

6000

50

1

Anodic alumina

6000

20

1

Stainless steel

3000

100

1

Density board

6000

60

1

Peddle

6000

100

1

Plastic board

6000

40

1

Cardboard

6000

50

1

Choose the correct port

Choose baud rate 115 200

Lightning sign

Successful

19

For cutting:

Material

Speed (mm/min)

Power (%)

Times

Plywood 1-3 mm

700-1000

100

1

Plywood 4 mm

500

100

1

Plywood 5 mm

300

100

1

Plywood 6 mm

150

100

1

Plywood 8 mm

100

1-2

Acrylic 1 mm

500

100

1

Acrylic 3 mm

200

100

1

Acrylic 6 mm

100

1-2

NOTE:

The energy value is set to 500, and the laser intensity accounts for 50 % of the power.

The energy value is set to 1000, and the proportion of laser intensity to power is 100 %.

The larger the energy, the faster the speed can be set.

The above parameters only for reference. Due to the different properties of the

materials, please adjust the parameter values according to the actual situations.

Machine testing guide

1. Turn on the machine and connect it to the computer.

2. Movement test:

Control the machine to move up down, left, and right on the software, check whether

the moving direction is correct (Figure A01), and check whether the moving distance is

correct (Figure A02).

3. Laser emission test:

The software imports the custom icon, click on the light (low light). Wear protective

glasses to observe whether the laser module emits blue light (Figure A03).

4. Test the files in the TF Card:

NOTE: Laser will generate heat and glare, which may cause harm. Please follow the

instructions to avoid injury.

20

Z-axis auto focusing configuration guide

Working principle:

The laser module lifter would move downward, once probe touching engraving surface,

Z-axis limit switch would be activated, and laser module would move upward to pre-set

lifting height. Once lifting height set in software, the machine would complete focusing

automatically.

When laser module moved 7 mm upward (lifting height set to 7 mm), the focal length

(distance between laser module to engraving surface) would be 50 mm.

Set the origin

Low laser

Strong laser

Emit the laser

Find edge on outline

Stránka sa načítava...

ALZA Totem TS2 Používateľská príručka

ALZA Totem TS2 Používateľská príručka

v iných jazykoch

Súvisiace články

Ostatné dokumenty