Creality CV-Laser Používateľská príručka

CV-Laser Module

User Manual • Uživatelský manuál •

Užívateľský manuál • Használati utasítás •

Benutzerhandbuch

2

English

3 – 24

Čeština

25 – 46

Slovenčina

47 – 68

Magyar

69 – 90

Deutsch

91 – 112

3

Dear customer,

Thank you for purchasing our product. Please read the following instructions carefully

before first use and keep this user manual for future reference. Pay particular attention

to the safety instructions. If you have any questions or comments about the device,

please contact the customer line.

󱭼󱭽󱭾󱭿󱮀 www.alza.co.uk/kontakt

✆ +44 (0)203 514 4411

Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Prague 7, www.alza.cz

4

Dear Consumers

Thank you for choosing our products. For the best experience, please read the

instructions before operating the product. Our team will always be ready to render you

the best service. Please contact us via the phone number or e-mail address provided at

the end when you encounter any problem.

Visit out official website www.creality.com to find relevant software/hardware

information, contact details and operation and maintenance instructions.

Notes

Using the hight-density laser beam to heat up the workpiece surface when engraving or

cutting aims to gasify without combustion. While most workpieces are essentially

combustible, which may be ignited, leading to open fire and consequently to the

machine breakdown and environment contamination. Please follow the following

operating principles.

1. It is prohibited to store the machine in areas close to combustible and explosive

substances, volatile solvents, or source of heat. Instead, store in a well-ventilated,

cool, and dust-free place.

2. Make sure that only the specific attached power cord rather than other similar

power cords are used during installation.

3. Do regular maintenance. Clean the product with a dry cloth when the power is

turned off, wiping away dust and foreign matter.

4. Ensure to turn the laser at 0°C-35°C. Operation at sub-zero temperature is

prohibited.

5. Switch off the machine if it is offline for an extended period of time and unplug

the power cord. It is prohibited to run the machine under wet environment or in

thunderstorm weather.

6. It is prohibited to come in contact with electronic areas with hands or other tools

when the machine is connected to power supply.

7. Touching any moving parts and laser module while the machine is running is

prohibited.

8. Wear goggles to prevent vision damage arising from exposure to the laser spot

during laser engraving operation.

9. It is advisable to run the machine under well ventilated condition at laser

engraving may generate small amount of fume or gas.

10. Children under 10 years old are not allowed to run the machine without adult

presence, which otherwise may lead to personal injury.

11. Put in place fire extinguishers in case of use, which shall be regularly checked. It

is prohibited to keep the machine unattended while it is running.

5

12. Users should comply with the laws and regulations of the corresponding

countries and regions where the equipment is located (used), abide by

professional ethics, pay attention to safety obligations, and strictly prohibit the

use of out products or equipment for any illegal purposes. Creality will not be

responsible for any violators’ legal liability under any circumstance.

Introduction

1. Eye protect exhaust hood

2. Laser head

3. Head screw

4. Focusing bar

5. Activated carbon smoking adsorption cotton

6. Axial fan

6

Equipment Parameters

1.6W

5W

Name

Laser Module

Model

CV-Laser Module

Size

185mm x 180mm x 85mm

Net Weight

400g

460g

Gross Weight

540g

600g

Power Supply

24V DC

Laser Source

Semiconductor laser unit

Lase wave length

450±5nm

455±nm

Lase power

1.6W

5W

Safety Class

Class IV (FDA classification standard)

Range of operation

temperature

0°C-35°C

Support materials

Cardboard, wood, bamboo, rubber, leather, fabric,

acrylic, plastic, etc.

Package Content

Laser Module x 1

Laser head fixing

plate x 1

Laser module wire x 1

Wood plate x 2

Brown paper x 2

Colour card paper x 7

Colour asphalt felt

paper x 7

M2 Socket head

wrench x 1

Soft magnetic strip x

2

Hexagon socket

countersunk head

screw x 4

Hexagon socket

Activated smoking-

adsorption cotton

x 2

Safety goggles x 1

Black cable tie x 3

Dustless cloth x 1

Instruction manual x

1

7

Assembling

1. Take the printer Ender-3 S1 as an example

Remove the hotend kit

Please make sure that before removing the hotend kit, you should firstly take off

the print material from the nozzle while it is heated. Disconnect the power and

allow it to cool to room temperature. Unplug the cable and loosen the four

screws to remove the hotend kit.

Unplug the flat

cable

Loosen the four screws

8

2. Install the laser head fixing plate

Take out the laser head fixing plate and the two Hexagon socket countersunk

head screw from the box, attach the fixing plate to the machine and tighten the

two countersunk screws using and Allen key (clockwise).

3. Installing the Laser Module

Take out the Laser Module and hand screw from the box, attach the Laser

Module to the fixing plate and tighten it using the hand screw (clockwise

direction)

Laser head

fixing plate x 1

Hexagon socket

countersunk head

screw x 2

M2 Socket head

wrench x 1

Laser Module

Hexagon

socket

9

4. One side of the laser module cable plugs into the machine’s expansion port and

the other side into the laser head.

Note: Installation and removal must be carried out in a power-off state, to avoid the risk

of burning out the motherboard.

Laser

Module

10

Firmware update

When using the laser module on the Ender-3 S1 for the first time, please check if the

motherboard firmware and the screen firmware are the applicable version respectively.

The method is as follows.

Connect the machine to the power supply, turn on the power switch on the side, select

“Control” - “Info”, the firmware version number should be V1.0.4 or above.

Otherwise, please download the latest version from the website link and update the

firmware of motherboard and screen: https://www.creality.com/download -> Accessory

Firmware -> CV-Laser Module Firmware

11

Motherboard firmware

Decompress the UPDATE.rar and copy it to SD card:

Insert the SD card into the machine and turn on the power to update automatically.

Screen firmware

Copy the private file to the TF card:

1. Unplug the screen cable and then remove the screen from the screen holder.

2. Use and Allen key to unscrew the four screws on the back of the screen and

remove the lower cover of the screen.

3. Insert TF card into the TF card slot of the motherboard, plug in the screen cable

and power on to update automatically.

4. After the update is complete, power off, remove TF card, reinstall the screen and

restart the machine.

Screen cable

terminals

M2 Sokcet head

wrench

TF card x 1 (Self-

Provided)

The screen holder

Four screws

12

Software installation

Please visit the following weblink Creality_Print: https://www.creality.com/download

Creality_Print either Windows or Mac system, please choose the right software version

when download.

1. Double click to open the software installation package, click “Next” – “Accept”.

2. Confirm the installation location of the software, click “Browse…” - “Next” –

“Install” (not recommended to install on C drive) – “Finish”

13

Software Intro

Open the Creality_Print software and click on the navigation button at the top right to

see the basic features.

14

Software usage

1. Add a printer

Take the Ender-3 S1 Laser as an example, click on the locations as shown to add

your machine to turn.

2. Make sure the current status is “Laser”

15

3. Click on the “Picture” button on the left and find the image file you need to

engrave. Open to import the picture into the CrealityPrint software.

16

4. Adjust the position, size, rotation angle and other parameters of the file in the

right-hand console, setting the processing mode and working parameters, finally

preview the processing effect of it.

5. Finally, click on “Generate G-Code” to save the engraving file on the SD card.

17

Engraving

1. Insert the SD card into the machine and turn on the power switch on the side.

2. After the machine is switched on, if you are using it for the first time, please

select laser engrave.

18

To switch from fusing to laser engrave, select “Control” – “Switched Laser engraving”.

The software pops up the following prompt box. Please ensure that the laser module is

installed correctly (note that the laser module must be installed and removed only when

the power is off) and select “Confirm”.

19

3. Please place the engraving material under the laser head, counter-clockwise push

the fixed focus bar, adjust the laser focus to the appropriate value through the

knob (different thickness of the material corresponding to different values), until

the focusing bar touches the engraved material surface when natural vertical

down. Finally, clockwise push the focusing bar until it is attached by the magnet,

then select “Finish”.

4. Return to the main interface, select “Auto Home”, wait for the machine back to

zero completed.

20

5. Select “Engrave” and press the knob to confirm.

Select “Run Range”, the laser head will move repeatedly around the maximum X and Y

edges. You can adjust the engraving material to the right position.

Stránka sa načítava ...

Creality CV-Laser Používateľská príručka

Creality CV-Laser Používateľská príručka

V iných jazykoch

Súvisiace články

Ďalšie dokumenty