Dolmar MH2464DF Návod na obsluhu

Kategória
Nožnice na živé ploty
Typ
Návod na obsluhu
Original Instruction Manual
Оригінальні інструкції з експлуатації
Oryginalna instrukcja obsługi
Manual de instrucţiuni original
Originalbetriebsanleitung
Eredeti használati útmutató
Pôvodný návod na obsluhu
Originální návod k obsluze
WARNING!
Read and understand this Manual. Always follow safety precautions in the Manual.
Improper use can cause serious injury!
УВАГА!
Прочитайте та зрозумійте ці інструкції з експлуатації. Завжди дотримуйтеся заходів безпеки, наведених у цих інструкціях з
експлуатації.
Невірне використання може призвести до серйозних травм!
OSTRZEŻENIE!
Przeczytać ze zrozumieniem niniejszą instrukcję. Zawsze przestrzegać zasad bezpieczeństwa podanych w instrukcji.
Nieprawidłowa obsługa może spowodować poważne obrażenia!
AVERTISMENT!
Trebuie să citiţi şi să înţelegeţi acest manual. Urmaţi întotdeauna măsurile de precauţie din manual.
Utilizarea necorespunzătoare poate cauza vătămări grave!
WARNUNG!
Lesen und studieren Sie diese Betriebsanleitung sorgfältig. Befolgen Sie stets die Sicherheitsanweisungen dieser Betriebsanleitung.
Bei unsachgemäßer Handhabung kann es zu schweren Verletzungen kommen!
FIGYELEM!
Olvassa el és értelmezze a kézikönyvet. Mindig tartsa be a kézikönyv biztonsági óvintézkedéseit.
A helytelen használat súlyos sérüléseket okozhat!
VÝSTRAHA!
Tento návod si prečítajte a pochopte ho. Vždy dodržiavajte bezpečnostné opatrenia uvádzané v návode.
Nesprávne používanie môže spôsobiť vážne poranenia!
VAROVÁNÍ!
Přečtěte si tuto příručku a ujistěte se, zda jste jejímu obsahu porozuměli. Vždy dodržujte bezpečnostní opatření uvedená v příručce.
Při nesprávném použití může dojít k vážnému zranění!
MH-246.4 D
MH-246.4 DF
2
Thank you very much for choosing the DOLMAR pole hedge
trimmer. We are pleased to offer you a product that is the result of
an extensive development program and many years of knowledge
and experience.
To safely obtain the best possible results from your DOLMAR pole
hedge trimmer, please read this manual thoroughly before using the
machine, and follow all instructions given herein to assure proper
operation of the DOLMAR pole hedge trimmer.
English
(Original instructions)
Table of Contents Page
Symbols ............................................................................................2
Safety instructions ............................................................................3
Technical data...................................................................................8
Designation of parts..........................................................................9
Assembly ........................................................................................10
Shoulder strap (optional accessory) ...............................................10
Fuel/refuelling .................................................................................11
Precautions before starting the engine ...........................................13
Operating the pole hedge trimmer ..................................................16
Maintenance ...................................................................................18
Storage ...........................................................................................23
Troubleshooting ..............................................................................25
Please note the following symbols when reading this instruction manual.
SYMBOLS
WARNING/DANGER Beware of pinching
Before usage, carefully read and fully
understand the instructions in this manual
Beware of electrical lines, risk of electrical
shock
PROHIBITION Fuel (Gasoline)
No smoking
Engine manual-start
No naked ame Emergency stop
Wear protective shoes First aid
Wear protective gloves ON/START
Keep working area clear of persons and
pets
OFF/STOP
Wear a protective helmet and eye and ear
protection
3
General Instructions
- Before usage, carefully read this manual and thoroughly familiarize yourself with
how to correctly handle the pole hedge trimmer. THIS EQUIPMENT CAN CAUSE
SERIOUS INJURY IF USED IMPROPERLY!
- Always provide detailed instructions on how to correctly use the pole hedge
trimmer when lending the equipment to another person. Make sure that the
instruction manual is handed over together with the pole hedge trimmer.
- First-time users should ask their dealer for basic instructions on the correct
handling of the pole hedge trimmer.
- Store this manual in a location where it is easily accessible for quick reference.
- Do not allow persons under the age of 18 to operate the pole hedge trimmer.
Individuals over 16 years old, however, may use the pole hedge trimmer for
training purposes if under the constant supervision of an adult familiar with the
operation of the pole hedge trimmer.
- Always use the pole hedge trimmer with the utmost care and attention.
- Never attempt to modify the equipment.
- Follow the regulations about handling of pole hedge trimmers in your country.
- Serious injury may result if the pole hedge trimmer is used in the following
circumstances. Do not use the pole hedge trimmer:
When feeling tired or ill.
After consumption of alcohol and/or medication.
At night or in poor lighting conditions.
During pregnancy.
Intended use
- This pole hedge trimmer has been designed for the sole purpose of trimming
hedges and bushes. Do not use the pole hedge trimmer for any other purposes.
Personal protective equipment
- Clothes worn should be functional and tight-tting without restricting movement.
Do not wear clothing or jewelry that could get entangled in underbrush or in the
machine.
- For adequate protection against injuries to head, eyes, feet, hands, as well as
hearing impairment, the following protective equipment and clothing must be
used when working with the pole hedge trimmer.
- To prevent injury to the head or the eyes, always wear a protective helmet (1)
with goggles or a visor (2).
- To avoid hearing impairment, wear adequate ear defenders (3) at all times.
- Use of a well-tting work overalls (4) is strongly recommended.
- Always wear rugged, leather working gloves (5) when operating the pole hedge
trimmer.
- When using the pole hedge trimmer, always wear sturdy shoes (6) with a non-slip
sole. Special work shoes ensure good footing and protect against injury.
- When touching blades or blade unit, wear protective gloves. Blades can cut bare
hands severely.
Work area safety
-
DANGER: Keep the pole hedge trimmer away from electric lines and
communication cables. Touching or approaching high-voltage lines with pole
hedge trimmer can result in death or serious injury. Watch power lines and
electrical fences around the work area before starting operation.
- Start and operate the engine only outdoors in a well ventilated area. Operation
in a conned or poorly ventilated area can result in death due to suffocation or
carbon monoxide poisoning.
- During operation, keep bystanders, in particular children, or animals at least
15 m away from the pole hedge trimmer. Stop the engine as soon as someone
approaches.
- Before operation, examine the work area for wire fences, stones, or other solid
objects. They can damage the blades.
-
WARNING: Use of this product can create dust containing chemicals which
may cause respiratory or other illnesses. Some examples of these chemicals
are compounds found in pesticides, insecticides, fertilizers and herbicides. Your
risk from these exposures varies, depending on how often you do this type of
work. To reduce your exposure to these chemicals: work in a well ventilated area,
and work with approved safety equipment, such as those dust masks that are
specially designed to lter out microscopic particles.
SAFETY INSTRUCTIONS
4
Starting the pole hedge trimmer
- Before assembling or adjusting the equipment, switch off the engine and remove
the spark plug cap.
- Before starting the pole hedge trimmer, always make sure that the machine is in
safe operational condition.
- Never attempt to start the engine if the equipment is damaged.
- Check the operation of the throttle lever safety mechanism. The lock-off lever
should have a smooth and easy action. Make sure that the lock-off lever functions
properly. Check that the handles are clean and dry and test the STOP switch to
ensure that it is functioning properly.
Always start the pole hedge trimmer in accordance with the directions provided in
this instruction manual.
Follow the instructions below to start the pole hedge trimmer
- Start the pole hedge trimmer only after the machine has been completely
assembled and all accessory parts have been attached.
- When starting the engine, keep the blades clear of your body and other object,
including the ground. The blades may move when starting and may cause serious
injury or damage to the blades and/or property.
- Before starting the engine, make sure that cutter blades are not obstructed by
any foreign objects such as stones, branches, etc.
- Stop the engine immediately if engine problems occur.
- When pulling the starter knob, hold the equipment rmly against the ground by
your left hand. Never step on the drive shaft.
- If the blades move at idle, stop the engine and adjust the idle speed down.
- When operating the pole hedge trimmer, always maintain a rm grip on both
handles. Wrap your ngers tightly around each handle, cradling the handle
between thumb and forenger. To keep the pole hedge trimmer under control at
all times, avoid changing your grip during operation. Make sure that the control
handles are in good condition and free of moisture, mud, oil or grease.
Always ensure secure and well-balanced footing
- Always stop the engine immediately and discontinue operation if engine trouble
occurs or if the machine starts making unusual noise.
- Exhaust fumes are poisonous. Never operate the machine in an enclosed room
or tunnel without ventilation (risk of suffocation and gas poisoning). Note that
carbon monoxide is an odorless gas. Always make sure that areas where the
engine is operated are adequately ventilated.
- Stop the engine when resting, or when the pole hedge trimmer is left unattended.
Place the machine in a safe location and make sure that no combustible material
is nearby.
- Never place a hot pole hedge trimmer onto dry grass or combustible material.
- To reduce the risk of re, keep the engine and mufer free of debris, leaves or
excessive lubricant.
- Never operate the engine if the mufer is malfunctioning.
- Turn off the engine before transportation.
- Always stop the engine when:
Resting
Transporting the machine
Cleaning the machine
Refuelling the machine
Performing maintenance on the machine
Fixing a problem with the machine
- When carrying the equipment, carry it in a horizontal position by holding the shaft.
Keep the hot mufer away from your body.
- When transporting the machine in a vehicle, always securely attach the pole
hedge trimmer to avoid leakage of residual fuel.
- Always empty the fuel tank before transporting the pole hedge trimmer in a
vehicle.
- When unloading the machine from a vehicle, take extra care not to drop the pole
hedge trimmer to the ground, as this may seriously damage the fuel tank.
- Except in an emergency, never drop the pole hedge trimmer as this may seriously
damage the machine.
- When transporting the pole hedge trimmer, always lift the machine completely off
of the ground. Never drag the engine across the ground as this may damage the
fuel tank and possibly cause a re.
- Always use the cutter cover provided to protect and secure the cutting section of
the pole hedge trimmer during transportation and storage.
- If the equipment gets heavy impact or fall, check the condition before continuing
work. Check the fuel system for fuel leakage and the controls and safety devices
for malfunction. If there is any damage or doubt, ask our authorized service
center for the inspection and repair.
- Resting
- Transporting the machine
- Cleaning the machine
- Refuelling the machine
- Performing maintenance on
the machine
- Fixing a problem with the
machine
5
Refuelling
- Before refuelling, stop the engine.
- Never refuel near naked ames.
- Do not smoke when refuelling.
- Always allow sufcient time for the engine to cool down before refuelling.
- Take care not to let your skin come into contact with petroleum products. Do not
inhale gasoline fumes and always wear protective gloves when refuelling.
Change and clean protective wear at regular intervals.
- Take extra care to avoid spilling gasoline and oil in order to avoid contamination
of the ground (environmental protection). If gasoline or oil has been spilled onto
the pole hedge trimmer, immediately wipe the surface of the pole hedge trimmer
with a rag.
To avoid spontaneous combustion, allow wet rags to dry sufciently before
discarding them into an appropriate, covered container.
- Make sure that no fuel comes in contact with your clothing. Change fuel-
contaminated clothing immediately (re hazard).
- Close the fuel tank and tighten the fuel tank cap securely. To restart the engine,
transfer the pole hedge trimmer to a location at least 3 meters away from the
place of refuelling.
- Check the fuel tank cap at regular intervals to make sure that the cap is securely
fastened.
- Never refuel the machine in an enclosed room. Fuel vapors accumulate at ground
level (risk of explosion).
- Store fuel in appropriate containers only, and make sure that stored fuel is out of
the reach of children.
Operation
- In the event of an emergency, turn off the engine immediately.
- If you feel any unusual condition (e.g. noise, vibration) during operation, switch off
the engine. Do not use the pole hedge trimmer until the cause is recognized and
solved.
- The blades continue to move for a short period after releasing the throttle trigger
or switch off the engine. Don’t rush to contact the blades.
- Never attempt to operate the equipment with one hand. Loss of control may result
in serious or fatal injury. To reduce the risk of cut injuries, keep your hands and
feet away from the blades.
- Keep your right hand under the shoulder height during operation. Otherwise you
may lose control and result in injury.
- During operation, never hit the blades against hard obstacles such stones and
metals. Take particular care when cutting hedges next to or against wire fences.
When working close to the ground, make sure that no sand, grit or stones get
between the blades.
- If the blades come into contact with stones or other solid objects, stop the engine
immediately and check the blades for damage after removing the spark plug cap.
Replace the blades if damaged.
- Never touch or approach the blades while they are moving. Blades can cut your
nger easily. When handling or approaching the blade, stop the engine and
remove the spark plug cap.
- If thick branches get jammed in the blades, immediately stop the engine, put the
pole hedge trimmer down and then remove the obstruction after removing the
spark plug cap. Check the blades for damage before using the equipment again.
- Accelerating the engine with the blades blocked increases the load and may
damage the engine and/or clutch.
- Check the cutting blades frequently during operation for cracks or blunt edges.
Before the inspection, switch off the engine and wait until the blades stop
completely. Replace damaged or dull blades immediately, even if they have only
supercial cracks.
- Do not touch the gear case. The gear case becomes hot during operation.
- Take a rest to prevent loss of control caused by fatigue. We recommend to take a
10 to 20-minute rest every hour.
- Before cutting, pull the throttle lever fully to achieve the maximum speed.
- During operation, hold the pole hedge trimmer with both hands at all times.
- Only use the pole hedge trimmer in good light and visibility conditions. Beware
of slippery and wet areas (ice and snow) during the cold season (danger of
slipping), and always ensure secure footing.
- Never use the pole hedge trimmer while standing on an unstable surface or a
steep slope.
- Never use the pole hedge trimmer while standing on a ladder.
- Never climb a tree to use the pole hedge trimmer from the tree.
- To avoid stumbling or falling over objects, never walk backwards when working
with the pole hedge trimmer.
- Always stop the engine before cleaning or servicing the machine. Also, refrain
from replacing parts before the engine has been stopped.
- Do not operate the pole hedge trimmer if the cutting unit is damaged or worn.
3 m
6
Maintenance work that can be performed by the user is limited to the activities
described in this instruction manual. Any other procedures are to be executed by an
authorized service agent.
Request DOLMAR authorized service center to inspect and maintain the pole hedge
trimmer at regular interval.
Use only genuine spare parts and accessories supplied by DOLMAR via authorized
service centers.
Use of unauthorized accessories and tools may increase the risk of accident and
injury. DOLMAR accepts no liability whatsoever for accidents or damage resulting
from the use of unauthorized accessories and parts.
Storage
- Before storing the equipment, perform full cleaning and maintenance. Fit the
blade cover.
- Empty the fuel tank before storage, and always store the pole hedge trimmer in a
well-ventilated locked room. Make sure the pole hedge trimmer is out of children’s
reach at all times.
- Do not prop the equipment against something, such as a wall. Otherwise the pole
hedge trimmer may fall suddenly and cause an injury.
First aid
As a precaution for the occurrence of an accident, make sure that a fully stocked
rst aid kit is ready at hand.
Replace any items taken from the rst aid kit as soon as possible.
When asking for help in the case of an emergency, give the
following information:
Place of accident
What happened
Number of injured people
Extent of injuries
Your name
Maintenance instructions
- Have your equipment serviced by our authorized service center, always using
only genuine replacement parts. Incorrect repair and poor maintenance can
shorten the life of the equipment and increase the risk of accidents.
- Always do your utmost to keep pollution and noise emissions as low as possible
when operating the pole hedge trimmer. Pay special attention to correct
adjustment of the carburetor.
- Clean the pole hedge trimmer at regular intervals and periodically check whether
all nuts and bolts are securely tightened.
- Never service or store the pole hedge trimmer in the vicinity of naked ames,
sparks, etc.
- Never repair bent or broken blades by straightening or welding. It may cause
parts of the blades to come off and result in serious injury. Contact DOLMAR
authorized service center for DOLMAR genuine blades to replace them.
- To prevent further damage and/or personal injury, refrain from repairing a
malfunctioning pole hedge trimmer if not qualied to do so. For repairs always
contact your dealer or an authorized service agent.
Do not attempt to modify or remodel the pole hedge trimmer as this may affect
operation safety.
Vibration
- People with poor circulation who are exposed to excessive vibration may
experience injury to blood vessels or the nervous system. Vibration may cause
the following symptoms to occur in the ngers, hands or wrists: “Falling asleep”
(numbness), tingling, pain, stabbing sensation, alteration of skin color or of the
skin. If any of these symptoms occur, see a physician!
- To reduce the risk of “white nger disease”, keep your hands warm during
operation and well maintain the equipment and accessories.
7
For European countries only
EC Declaration of Conformity
Makita declares that the following machine(s):
Designation of Machine: Petrol Pole Hedge Trimmer
Model No./ Type: MH-246.4 D, MH-246.4 DF
Conforms to the following European Directives:
2000/14/EC, 2006/42/EC
They are manufactured in accordance with the following standard or standardized documents:
EN ISO 10517
The technical le in accordance with 2006/42/EC is available from:
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
The conformity assessment procedure required by Directive 2000/14/EC was in accordance with annex V.
MH-246.4 D:
Measured Sound Power Level: 102.2 dB
Guaranteed Sound Power Level: 104 dB
MH-246.4 DF:
Measured Sound Power Level: 102.2 dB
Guaranteed Sound Power Level: 103 dB
1. 12. 2014
Yasushi Fukaya
Director
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
8
Model
MH-246.4 D MH-246.4 DF
Loop handle Straight handle
Dimensions (L x W x H) 2,550 mm x 242 mm x 241 mm 2,050 mm x 221 mm x 241 mm
Net weight 6.9 kg 6.6 kg
Volume (fuel tank) 0.6 L
Cutting length 490 mm
Maximum branch diameter 7 mm
Cutting strokes 4,200 min
-1
Engine type Air cooled, 4-stroke, single cylinder
Engine displacement 25.4 cm
3
Maximum engine performance 0.77 kW at 7,000 min
-1
Engine speed
at recommended max, spindle speed
10,000 min
-1
Fuel consumption 0.33 kg/h
Specic fuel consumption 408 g/kWh
Idling speed 3,000 min
-1
Clutch engagement speed 4,400 min
-1
Carburetor
(Diaphragm carburetor)
Diaphragm type
Spark plug type NGK CMR4A
Electrode gap 0.7 - 0.8 mm
Vibration per ISO 10517 Vibration per ISO 22867
Right handle (rear grip)
a
hv eq
8.9 m/s² 8.0 m/s²
Uncertainty K 3.3 m/s² 1.1 m/s²
Left handle (front grip)
a
hv eq
6.3 m/s² 8.0 m/s²
Uncertainty K 1.4 m/s² 1.4 m/s²
Noise per ISO 10517 Noise per ISO 22868
Sound pressure level 90 dB (A) 90.2 dB (A)
Uncertainty K 1.8 dB (A) 1.0 dB (A)
Sound power level 102.2 dB (A) 102.2 dB (A)
Uncertainty K 1.6 dB (A) 0.6 dB (A)
Fuel Automobile gasoline (petrol)
Engine oil
API grade SF class or higher, SAE 10W-30 oil
(automobile 4-stroke engine oil)
Gear ratio 1/4.78
TECHNICAL DATA
9
Designation of parts
1 Throttle cable
2 Lock-off lever
3 Throttle lever
4 Stop switch
5 Handle
6 Shaft
7 Gear box
8 Cutter blade
9 Air cleaner
10 Fuel tank cap
11 Fuel tank
12 Clutch case
13 Spark plug cap
14 Primer pump
15 Mufer
16 Recoil starter
17 Starter knob
18 Blade cover
19 Oil cap
20 Oil tank
21 Shoulder strap
(Optional accessory)
DESIGNATION OF PARTS
MH-246.4 D
MH-246.4 DF
21
9
10
11
12
14
15
19
20
16
17
18
1
2
3
4
5
6
7
8
13
17
1
2
3
4
6
7
8
13
17
10
WARNING:
Make sure that the engine is turned off, and remove the spark plug cap before
assembling the pole hedge trimmer.
Wear protective gloves!
Secure cutting blades with the blade cover provided when connecting the trimmer
unit to the pole.
1. Remove the cap (1) from the shaft.
2. Loosen the M5 x 16 bolt (2) and M5 x 25 bolt (3).
3. Insert shaft (4) into the cover (5).
NOTE: Make sure that the shaft is completely inserted into the cover
(approx. 237 mm/ 9-3/8”).
If you are having trouble inserting the shaft, manually rotate the drive axle
(6) a little and try again.
4. Make sure that the shaft is properly inserted and then tighten the M5 x 16 bolt
and the M5 x 25 bolt.
(2)
(1)
(4)
(6)
(5)
(3)
MH-246.4 D MH-246.4 DF
(1)
ASSEMBLY
to engine
Arrow mark
ATTACHING THE HANDLE (for MH-246.4 D)
- Fix the loop handle on the shaft as shown.
- To keep a proper distance between the grips, set the loop handle ahead of the
arrows.
How to wear the shoulder strap
- Wear the shoulder strap over the left shoulder.
- Keep the pole hedge trimmer unit on the right hand side of the body.
- Attach the strap to the hanger provided on the pole hedge trimmer and adjust the
length of the strap to attain a comfortable working position.
Detachment
- In an emergency, push the notches (1) at both sides, and you can detach the
machine from you.
Be extremely careful to maintain control of the machine at this time. Do not allow
the machine to be deected toward you or anyone in the work vicinity.
WARNING: Failure to maintain complete control of the machine at all could result in
serious bodily injury or DEATH.
SHOULDER STRAP (optional accessory)
11
BEFORE START OF OPERATION
Inspection and rell of engine oil
- Perform the following procedure, with the engine cooled down.
- Set the engine level, remove oil cap (Fig. 1), and check to see whether or not there is oil in the range between the upper limit and lower limit
marks of the oil pipe (Fig. 2).
- Top up with oil to upper limit mark if oil is insufcient (oil level is close to lower limit mark) (Fig. 3).
- The area surrounding the external marks is transparent, so the amount of oil inside can be checked without having to remove the oil cap.
However, if oil pipe becomes extremely dirty, visibility may be lost, and oil level will have to be checked against stepped section on inside of
oil pipe.
- For reference, the oil rell time is about 10 h (every 10 refuelling).
If the oil changes in color or mixes with dirt, replace it with new one. (For the interval and method of replacement, refer to P20)
Recommended oil: SAE 10W-30 oil of API Classication, Class SF or higher (4-stroke engine for automobile)
Oil volume: Approx. 0.08 L
NOTE: If the engine is not kept upright, oil may go into around the engine, and may be relled excessively.
If the oil is lled above the limit, the oil may be contaminated or may catch re with white smoke.
Point 1 in Replacement of oil: “Oil cap”
- Remove dust or dirt near the oil rell port, and detach the oil cap.
- Keep the detached oil cap free of sand or dust. Otherwise, any sand or dust adhering to the oil cap may cause irregular oil circulation or
wear on the engine parts, which will result in troubles.
(2) Fill with oil to upper limit mark. (see Fig. 3)
Use oil bottle when lling.
(3) Securely tighten the oil cap. Insufcient tightening may cause oil leakage.
Oil cap
Oil pipe
Fig. 1 Fig. 2 Oil pipe Fig. 3
Internal stepped
section (upper limit)
External mark
(upper limit)
External mark
(lower limit)
Internal stepped
section (lower limit)
Top up with oil
until oil level
reaches internal
stepped section
(upper limit).
The area between the
external upper and lower
limits is transparent, so
oil level can be checked
extternally against these
marks.
(1) Keep the engine level, and detach the oil cap.
FUEL/REFUELLING
12
Note
Do not replace oil with the engine in a tilted position.
Filling with oil while engine is tilted leads to overlling which causes oil contamination and/or white smoke.
Point 2 in Replacement of oil: “If oil spills out”
- If oil spills out between the fuel tank and engine main unit, the oil is sucked into through the cooling air intake port, which will contaminate
the engine. Be sure to wipe out spilled oil before start of operation.
REFUELLING
Handling of fuel
It is necessary to handle fuel with utmost care. Fuel may contain substances similar to solvents. Refuelling must be performed in a sufciently
ventilated room or in the open air. Never inhale fuel vapors, and keep fuel away from you. If you touch fuel repeatedly or for a long time, the
skin becomes dry, which may cause skin disease or allergy. If fuel comes into the eye, clean the eye with fresh water. If your eye remains still
irritated, consult your doctor.
Storage period of fuel
Fuel should be used within a period of 4 weeks, even if it is kept in a special container in a well-ventilated and shaded area.
Otherwise, fuel may deteriorate in one day.
STORAGE OF MACHINE AND REFILL TANK
- Keep the machine and tank at a cool place free from direct sunshine.
- Never keep the fuel in a car.
Fuel
The engine is a four-stroke engine. Be sure to use an unleaded automobile gasoline 87 or higher octane ((R+M)/2). It may contain no more than
10% alcohol (E-10).
Points for fuel
- Never use a gasoline mixture which contains engine oil. Otherwise, it will cause excessive carbon accumulation or mechanical troubles.
- Use of deteriorated oil will cause irregular start-up.
Refuelling
WARNING: INFLAMMABLES STRICTLY PROHIBITED
- Loosen the tank cap a little to release the tank pressure.
- Detach the tank cap, and refuel, discharging air by tilting the fuel tank so that the refuel port will be oriented upward. (DO NOT ll fuel up to
the top of the tank.)
- Wipe well the periphery of the tank cap to prevent foreign matter from entering the fuel tank.
- After refuelling, securely tighten the tank cap.
If there is any aw or damage on the tank cap, replace it.
The tank cap wears out in course of time. Replace it every two to three years.
Fuel tank
Fuel upper
limit
Fuel tank cap
13
(2)
- At all times allow a 15-meter diameter safety zone around the working area.
Make sure that all persons (in particular children) and/or animals remain outside
this zone.
- Before using the pole hedge trimmer, make sure that the machine is in safe
operational condition. Make sure that the cutting blades are not damaged, and
check the throttle lever for easy action. Make sure that the cutting blades are
not in motion when the engine is idling. If the machine is not operating normally,
contact your dealer to have the machine adjusted. Make sure that the handles
are clean and dry, and test whether the I-O switch is functioning properly. Start
the engine only in accordance with the instructions given in this manual. Do not
use any other methods to start the pole hedge trimmer.
- Start the engine of the pole hedge trimmer only after having read and fully
understood the instructions. Never attempt to start a pole hedge trimmer that has
not been fully assembled. Serious injury may result otherwise.
- Before starting the engine, always make sure that the cutting blades are not
obstructed by stones, branches or any other solid objects.
- Check the working area for wires, cord, glass or other foreign objects that could
get caught in the cutting blades.
- Electrical shock: Be aware of all electrical lines in the vicinity. Check the entire
work area for the presence of power lines and electrical fences before starting to
work.
POINTS IN OPERATION AND HOW TO STOP
Observe the applicable accident prevention regulations!
STARTING
Move at least 3 m away from the place of refuelling. Put the pole hedge trimmer on
a clean piece of ground taking care that the cutting blades do not come into contact
with the ground or any other objects.
A: Cold start
1) Set this machine on a at space.
2) Set the I-O switch (1) to OPERATION.
3) Primer pump
Continue to push the primer pump (2) until the fuel comes into the primer pump.
(In general, fuel comes into the primer pump by 7 to 10 pushes.) If the primer
pump is pushed excessively, an excess of gasoline returns to the fuel tank.
OPERATION
Lock-off lever
Low speed
High
speed
(1)
STOP
Throttle lever
PRECAUTIONS BEFORE STARTING THE ENGINE
14
4) Recoil starter
Pull the start knob gently until it is hard to pull (compression point). Then, return
the start knob, and pull it strongly. Never pull the rope to the full extension. Once
the start knob is pulled, never release your hand immediately. Hold the start
knob until it returns to its original point.
5) Warm-up operation
Continue warm-up operation for 2 to 3 minutes.
NOTE: In case of excessive fuel intake, remove the spark plug and pull the starter
handle slowly to remove excess fuel. Also, dry the electrode section of the
spark plug.
B: Startup after warm-up operation
1) Repeat pushing the primer pump gently.
2) Keep the throttle lever at the idling position.
3) Pull the recoil starter strongly.
4) If it is difcult to start the engine, open the throttle by about 1/3.
Pay attention to the cutting blades which may move.
At times, such as winter, when starting the engine is difcult, operate choke
lever with the following procedure when starting engine.
After implementing startup steps 1) to 3), set choke lever to the CLOSE position.
Implement startup step 4) and start engine.
Once engine starts, set choke lever to the OPEN position.
Implement startup step 5) and complete warm up.
CAUTION: If a bang (explosive sound) is heard and the engine stops, or the
just-started engine stalls before the choke lever is operated, return the
choke lever to the OPEN position, and pull the starter knob a few times
again to start the engine.
CAUTION: If the choke lever is left in the CLOSE position, and the starter knob
merely pulled repeatedly, to much fuel will be sucked in, and the engine
will become difcult to start.
15
(1)
STOPPING
1) Release the throttle lever (2) fully, and when the engine speed has lowered, set
the I-O switch (1) to STOP the engine will now stop.
2) Be aware that the cutting head may not stop immediately and allow it to slow
down fully.
ADJUSTMENT OF LOW-SPEED ROTATION (IDLING)
When it is necessary to adjust the low-speed rotation (idling), perform it by the
carburetor adjusting screw (1).
CHECKUP OF LOW-SPEED ROTATION
- Set the low-speed rotation to 3,000 rpm (/min).
If it is necessary to change the rotation speed, regulate the adjusting screw (1)
with Phillips screwdriver.
- Turn the adjusting screw to the right, and the engine speed will increase. Turn the
adjusting screw to the left, and the engine speed will drop.
- The carburetor is generally adjusted before shipment. If it is necessary to readjust
it, please contact Authorized Service Center.
STOP
(1)
(2)
16
- Do not touch the cutting blade portion of the pole hedge trimmer during operation,
or when the engine is running.
- Take extra care not to inhale exhaust gases when working with the pole hedge
trimmer. Never operate the pole hedge trimmer in an enclosed room or an area
with insufcient ventilation (risk of suffocation and gas poisoning). Note that
carbon monoxide is an odorless gas that is, it cannot be detected by the sense of
smell.
- Always wear adequate protective wear before starting to work with the pole
hedge trimmer.
- Stop the engine immediately if the mufer is not functioning properly.
- Only use the pole hedge trimmer in good light and visibility conditions.
- Do not operate the pole hedge trimmer in darkness or fog. Beware of slippery and
wet areas (ice and snow) during the cold season (danger of slipping), and always
ensure secure footing.
- Never use the pole hedge trimmer while standing on an unstable surface or a
steep slope.
- Never use the pole hedge trimmer while standing on a ladder.
- Never climb a tree to use the pole hedge trimmer from the tree.
- Continuously check the working area for wires, cord, glass or other foreign
objects that could get caught in the cutting blades.
- Make sure that the cutting blades are in rapid motion before starting to cut.
- Always grip the pole hedge trimmer with both hands and maintain a rm grip
when working with the machine.
- To assure optimal control over the pole hedge trimmer, always completely wrap
your hands around the handles (use your thumb for counter pressure) and apply
a rm grip on the handles.
- Note that the cutting blades will remain in motion for up to two seconds after the
throttle lever has been released.
- Do not cut with the pole hedge trimmer at low engine speed.
- The speed of the cutting blades cannot be adjusted properly with the throttle lever
when the engine is running at low speed.
- To trim the top surface of a hedge, rst align the cutting blades at an angle of
15° - 30° in the cutting direction and keep the pole hedge trimmer in a horizontal
position. Then start trimming the hedge using a swinging movement, much like
drawing circle segments with the hedge trimmer shaft.
- To trim the sides of a hedge, align the blades parallel to the surface to be cut and
start trimming with semi-circular upward (down-up) movements.
- Pay attention when trimming a hedge close to or against wire fences.
- Do not touch hard objects such as wire fence, stone or ground with the cutting
blades. It may cause blades to crack, chip or break.
- Do not use the pole hedge trimmer over an extended period of time. As a general
rule, for every 50 minutes of operation take a 10-20 minutes rest.
- If the cutting blades come into contact with stones or other solid objects, stop
the engine immediately and check the blades for damage. Replace the blades if
damaged.
- If the pole hedge trimmer develops a problem during operation (strange noises,
vibration, etc.), immediately stop the engine. Do not use the machine again until
the problem has been recognized and solved.
- Always do your utmost to keep pollution and noise emissions as low as possible
when operating the pole hedge trimmer. Pay special attention to correct
carburetor adjustment.
- If thick branches get jammed in the cutting blades, immediately stop the engine,
lay the equipment on the ground and remove the obstruction. Check the blades
for damage before using the machine again.
OPERATING THE POLE HEDGE TRIMMER
MH-246.4 D
MH-246.4 DF
17
Adjustment of cutting angle
Warning:
- Do not operate the tool with the loose and unstable cutter unit.
You can adjust the cutting angle upwards to 45°and downwards to 90°.
1. Stop the pole hedge trimmer engine and lay the machine on the ground.
2. To adjust the angle of the cutter unit, hold the handle (A) on the cutter unit with
one hand, and hold the angle lock (B) as illustrated with the other hand.
3. Pull the angle lock gently, and change the angle of the cutter unit. After
adjusting the angle, return the angle lock gently.
Note:
- The cutter unit is fasten only with certain angles alongside the groove on the
unit. Make sure the cutter unit sits properly. If the angle is not appropriate, the
clutch is cut and the tool does not operate.
- Do not adjust the cutter unit while the pole hedge trimmer is in an upright
position.
- Move the I-O switch to the “O” position and lay the pole hedge trimmer at on
the ground to adjust the cutting angle.
- Always secure the blades with the blade cover provided before adjusting cutting
angle.
In case the cutter unit is loose, the bolt (the axis of angle adjustment) needs to be
tightened.
1. Set the socket wrench (1) and the hex wrench (2) on the bolt (3).
2. Adjust the tightness of the cutter unit by turning hex wrench, and then fasten
the bolt by turning the socket wrench.
Note:
- Do not fasten the cutter unit too tight. The angle of the cutter unit can not be
changed if it is too tight.
A
B
(2)
(3)
(1)
18
- Before performing any maintenance work on the pole hedge trimmer (blade cleaning, etc.), always stop the engine and wait until the engine
has cooled down.
As an additional safety precaution, also remove the spark plug cap.
- Do not try to straighten or weld bent or broken cutting blades. Always replace damaged blades.
- Stop the engine at regular intervals to check the cutting blades for possible damage (perform a tapping-resonance test to detect hard-to-see
hairline cracks). Always make sure that the teeth of the blades are sharp.
- Clean the pole hedge trimmer regularly. During cleaning also check all screws, nuts and bolts are well tightened.
- To reduce the risk of re, never service or store the pole hedge trimmer in the vicinity of open res.
- Always wear rugged protective gloves when handling the cutting blades.
- Contact your dealer for replacement cutting blades.
- Never use gasoline, benzine, thinner, alcohol or the like for cleaning.
Discoloration, deformation or cracks may result.
Sharpening the blade
If the cutting blades have become blunt and cutting performance is poor, have the blades sharpened by an authorized service agent.
Adjusting blade clearance
The upper/lower blades wear out gradually after operations. If you cannot get a clean cut though the blades are sharp enough, adjust the
clearance as follows.
The tightness of the hex bolt decides the clearance of the blades. The nut holds the hex bolt with certain tightness. Too loose clearance causes
blunt cut, but too tight clearance causes unnecessary heat and sooner worn-out of the blades.
1. Loosen the nut (1) with a box or open-ended wrench.
2. Tighten the hex bolt (2) with a hex wrench lightly till it stops. And then, screw it back between a quarter turn and a half turn to gain necessary
clearance.
3. Tighten the nut (1), holding the hex bolt (2).
4. Apply light oil on the friction surface of the blades.
5. Start the engine, operate the throttle on and off for a minute.
6. Stop the engine and touch the surface. If they are not too hot to touch, you have made a proper adjustment. If they are too hot to touch, turn
the hex bolt (2) back a little and repeat the step 5 to 6.
NOTE: Before making the adjustment, stop the engine and wait for the blades to stop.
The blades have a slot around the hex bolt (2). In case you nd dust in the end of any of the slots, clean it.
3
1
2
3
4
5
6
1
2
3
3
4
7
5
6
MH-246.4 D
MH-246.4 DF
1 Hexagonal U-nut
2 Hex bolt
3 Plate
4 Blade guide
5 Upper blade
6 Lower blade
7 Blade guard
MAINTENANCE
19
B
A
Adding grease and lubricant
Important: Make sure that the surface of gear box is completely cold before
lubricating.
- The gearbox of the pole hedge trimmer should be greased every 25 working
hours. The grease hole locates under the bolt. Remove the bolt to lubricate. Add
approx. 3 g (4 cc) of lubricant to the point A of the gearbox and 5 g (7 cc) of the
lubricant to the point B respectively via the grease hole. Return the bolt after
lubrication. After lling correct amount of grease, grease will come out a bit from
the base of the blade during the rst operation.
CAUTION: Observe greasing intervals and the amount of grease to be supplied.
Mechanical parts of the pole hedge trimmer may be damaged if grease
is not supplied at the prescribed intervals or if an insufcient amount of
grease is added.
Daily inspection and maintenance
To ensure a long service life of your pole hedge trimmer, perform the following
inspections and maintenance on a daily basis.
- Before use;
Always check for loose or missing parts before starting operation. Pay special
attention to the cutting unit and make sure that the cutting blade lock screws
are well tightened.
Check for clogging of the cooling air passages and the cooling ns of the
cylinder before starting operation. Clean if necessary.
- After use;
Clean the pole hedge trimmer externally and inspect for damage.
Clean the air lter. Clean the lter several times a day if working in extremely
dusty conditions.
Check the cutting blades for damage. Make sure that the blades are securely
mounted.
If the cutting blades still continue to run at idle after the adjustment, consult
your nearest authorized service agent.
Grease hole
(under the bolt)
20
In replacement, perform the following procedure.
1) Make sure that the fuel tank cap is tightened securely.
2) Put large container (pan, etc.) under drain hole.
3) Remove drain bolt and then remove oil cap to drain out oil from drain hole. At
this time, be sure not to mislay drain bolt’s gasket, or to dirty any of the removed
components.
4) Once all the oil has been drained, combine gasket and drain bolt, and tightly
secure drain bolt, so that it will not loosen and cause leaks.
* Use cloth to fully wipe off any oil attached to bolt and equipment.
Alternative draining method
Remove oil cap, tilt pole hedge trimmer toward oil ller hole, and drain out oil.
Collect oil in container.
REPLACEMENT OF ENGINE OIL
Deteriorated engine oil will shorten the life of the sliding and rotating parts to a great extent. Be sure to check the period and quantity of
replacement.
DANGER: In general, the engine main unit and engine oil still remain hot just after the engine is stopped. In replacement of oil, make
sure that the engine main unit and engine oil are sufciently cooled down. Otherwise, there may remain a risk of scald.
Allow sufcient time after stopping engine for the engine oil to return to the oil tank to ensure accurate reading of the oil
level indicator.
NOTE: If the oil lled above the limit, it may become dirty or may catch re with white smoke.
Interval of replacement: After rst 20 operating hours, followed by every 50 operating hours
Recommended oil: SAE10W-30 oil of API Classication SF Class or higher (4-stroke engine oil for automobile)
Fuel tank cap
Oil cap
Oil cap
Drain hole
Gasket
Drain bolt
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196

Dolmar MH2464DF Návod na obsluhu

Kategória
Nožnice na živé ploty
Typ
Návod na obsluhu