Parkside 113076 Translation Of The Original Instructions

BENCH GRINDER WITH BELT SANDER PSBS 240 B2

ST AND-BANDSCHLEIFER

Originalbetriebsanleitung

BENCH GRINDER WITH BELT SANDER

Translation of the original instructions

S

ZLIFIERKA TAŚMOWA

Tłumaczenie oryginalnej instrukcji obsługi

P

ÁSOVÁ BRUSKA

Překlad originálního provozního návodu

STOJANOVÁ PÁSOVÁ BRÚSKA

Preklad originá lneho návodu na obsluhu

S

TOJEČI TRAČNI BRUSILNIK

Prevod originalnega navodila za uporabo

ÁLLVÁNY OS SAROKCSISZOLÓ

Az originál használati utasítás fordítása

IAN 113076

113076_par_Stand-Bandschleifer_cover_PL_HU_SI_CZ_SK.indd 2 14.04.15 14:56

GB Translation of the original instructions Page 4

PL Tłumaczenie oryginalnej instrukcji obsługi Strona 19

HU Az originál használati utasítás fordítása Oldal 35

SI Prevod originalnega navodila za uporabo Stran 51

CZ Překlad originálního provozního návodu Strana 65

SK Preklad originálneho návodu na obsluhu Strana 80

DE / AT / CH Originalbetriebsanleitung Seite 95

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the

device.

Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi

funkcjami urządzenia.

Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik

funkcióját.

Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.

Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.

Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

113076_par_Stand-Bandschleifer_cover_PL_HU_SI_CZ_SK.indd 3 14.04.15 14:56

1

19

3

2a

2

19

18

17

17a

17b

17c

1 2

3 4

8 97

5 6

10

11

12

13

16

15

14

17

18

19

14b

14a

4

GB

Introduction

Congratulations on the purchase of your

new device. With it, you have chosen a

high quality product.

During production, this equipment has

been checked for quality and subjected

to a nal inspection. The functionality of

your equipment is therefore guaranteed. It

cannot be ruled out that residual quantities

of water or lubricants will remain on or in

the equipment/hose lines in isolated cases.

This is not a fault or defect and it repre-

sents no cause for concern.

The operating instructions constitute

part of this product. They contain

important information on safety, use

and disposal.

Before using the product, familiarise

yourself with all of the operating

and safety instructions. Use the

product only as described and for

the applications specied.

Keep this manual safely and in the

event that the product is passed on,

hand over all documents to the third

party.

Intended use

The bench grinder with belt sander is a sta-

tionary grinding device for the coarse and

ne grinding of metal, wood and plastic. It

is suitable for deburring, rust removal and

grinding.

The device is not intended for all other

types of applications (e.g. grinding with

unsuitable grinding tools, grinding with a

coolant solution, grinding hazardous mate-

rials such as asbestos).

The equipment is intended for use in the

eld of DIY. It is not designed for commer-

Content

Introduction .................................4

Intended use ................................ 4

General description ......................5

Scope of delivery ............................. 5

Function description.......................... 5

Summary ........................................ 5

Technical specications ................. 6

Safety Instructions........................6

Symbols and icons ........................... 7

General safety instructions ................ 7

Further Safety Instructions .................. 9

Residual risks ................................. 10

Assembly ...................................10

Assemble/set spark protection ......... 10

Assemble/set workpiece supports .... 11

Screw device on to workbench ........ 11

Operation ..................................11

Switching on and off ...................... 12

Grinding with the grinding disc ....... 12

Tape loops .................................... 12

Change grinding belt ..................... 12

Change grinding disc ..................... 13

Cleaning and maintenance ......... 14

Cleaning ....................................... 14

Maintenance ................................. 14

Storage ......................................14

Waste disposal and

environmental protection ...........14

Replacement parts/accessories ...15

Trouble Shooting ........................ 16

Guarantee .................................17

Repair Service ............................18

Service-Center ............................18

Importer .................................... 18

Translation of the original

EC declaration of conformity ....111

Exploded Drawing ...................117

5

GB

cial use.

The equipment is designed for use by

adults. Young people under the age of 16

are permitted to use the equipment only

under supervision.

The manufacturer shall not be liable for

damages caused by use other than for the

intended purpose or by incorrect opera-

tion.

General description

The illustrations can be found

on the front and rear fold-out

pages.

Scope of delivery

Unpack the equipment and check that it is

complete. Dispose of the packaging mate-

rial correctly.

- Appliance

- Transparent spark protection (

1)

- Adjusting screw for spark protection

(

2) (1 cross-drive screw incl. spring

washer and washer as well as nut)

- 2 workpiece supports (

6/18) with

mounting material (2 star grip nuts

(

5/17), 2 screws, 2 washers,

2toothed lock washers

- Instruction Manual

Function description

The bench grinder with belt sander is a

combined device equipped with a grinding

disc and an adjustable grinding belt. The

device is provided with a spark protection

and protective hoods for the protection of

the user.

For the function of the operating parts,

please refer to the descriptions below.

Summary

1 Spark protection (two-piece)

2 Adjusting screw for spark protec-

tion

3 Protective hood grinding disc

4 Engine housing

5 Star grip nut to install the work-

piece support grinding belt

6 Workpiece support grinding belt

7 Clamping lever grinding belt

8 Clamping screw for upper belt

idler

9 Protective hood grinding belt

10 Grinding belt

11 Fixing screws for grinding disc

cover

12 Grinding disc cover

13 Bore holes for table mounting

14 On/off switch

14a On switch

14b Off switch

15 Fixing screws for grinding disc

cover

16 Grinding disc cover

17 Star grip nut to mount/adjust the

workpiece support grinding disc

18 Workpiece support grinding disc

19 Grinding disc

20 Upper (a) and lower (b) roller

21 Adjusting screw tape run

6

GB

Technical specications

Nominal input voltage ........ 230 V~, 50 Hz

Power consumption ..................... 240 W

(S2 30 min)*

Safety class ..........................................I

Mechanical rating .......................... IP 20

Measurement idling speed n

0

.... 2950 min

-1

Grinding disc

Outer diameter ......................Ø 150 mm

Bore hole ..............................Ø 12.7 mm

Thickness .....................................20 mm

Granulation .......................................36

Velocity v

0

...........................max. 23 m/s

Grinding belt

Dimension .........................50 x 686 mm

Granulation .......................................80

Velocity v

0

...................................15 m/s

Weight (incl. accessories) .. approx. 7.2 kg

Sound pressure level

(L

pA

) ........................ 89 dB(A); K

pA

=3 dB

Sound power level (L

wA

)

measured .............. 102 dB(A); K

wA

=3 dB

Vibration total value (a

h

) .......... 2,5 m/s

2

* A break is introduced after 30 minutes of

uninterrupted operating duration until the de-

vice temperature differs 2 K (2°C) less than

room temperature.

Noise and vibration values have been

determined according to the standards and

regulations mentioned in the declaration of

conformity.

Technical and optical changes may be

undertaken in the course of further develop-

ment without notice. All dimensions, refer-

ences and information in this instruction

manual are therefore not guaranteed. Legal

claims made on the basis of the instruction

manual can therefore not be considered as

valid.

The stated vibration emission value was

measured in accordance with a standard

testing procedure and may be used to com-

pare one power tool to another.

The stated vibration emission value may

also be used for a preliminary exposure

assessment.

Warning!

The vibration emission value may

differ during actual use of the

power tool from the stated value

depending on the manner in which

the power tool is used.

Safety precautions aimed at protect-

ing the user should be based on

estimated exposure under actual

usage conditions (all parts of the

operating cycle are to be consid-

ered, including, for example, times

during which the power tool is

turned off and times when the tool

is turned on but is running idle).

Safety Instructions

WARNING!

When using power tools, observe

the following basic safety measures

for the prevention of electric shocks

and the risk of injury and re.

Please read all these instructions

before using the electric tools and

please keep the safety instructions.

7

GB

Symbols and icons

Symbols on the device:

Warning!

Risk of injury from the rotating tool!

Keep hands away.

Risk of electric shock! Disconnect

from the mains before carrying out

maintenance and repair work.

Read the instruction manual.

Wear ear protection.

Wear eye protection.

Wear breathing protection.

Risk of cuts.

Wear cut-resistant gloves.

Never use faulty grinding disks.

Do not dispose of electrical equip-

ment in household waste.

Dimensions grinding disk

Dimensions grinding belt

Symbols in the manual:

Warning symbols with in-

formation on damage and

injury prevention.

Instruction symbols (the instruction is

explained at the place of the excla-

mation mark) with information on

preventing damage.

Help symbols with information on

improving tool handling.

General safety instructions

Safe operation:

• Keep work area clear. Cluttered

areas and benches invite injuries.

• Consider work area environ-

ment.

- Do not expose tools to rain. Do not

use tools in damp or wet locations.

Water entering a power tool will in-

crease the risk of electric shock.

- Keep work area well lit.

- Do not use tools in the presence of

ammable liquids or gases.

Power tools create sparks which may

ignite the dust or fumes.

• Guard against electric shock.

Avoid body contact with earthed or

grounded surfaces (e.g. pipes, radia-

tors, ranges, refrigerators).

• Keep other persons away.

Do not let persons, especially children,

not involved in the work touch the tool

or the extension cord and keep them

away from the work area.

• Store idle tools. When not in use,

tools should be stored in a dry locked-

up place, out of reach of children.

• Do not force the tool. It will do

the job better and safer at the rate for

which it was intended.

• Use the right tool.

- Do not force small tools to do the job

of a heavy duty tool.

- Do not use tools for purposes not

intended; for example do not use cir-

cular saws to cut tree limbs or logs.

Use of the power tool for operations dif-

ferent from those intended could result in

a hazardous situation.

8

GB

• Dress properly.

- Do not wear loose clothing or jewel-

lery, they can be caught in moving

parts.

- Anti-slip footwear is recommended

when working outdoors.

- Wear protective hair covering to con-

tain long hair.

• Use protective equipment.

- Use safety glasses.

- Use face or dust mask if working op-

erations create dust.

• Connect dust extraction equip-

ment. If the tool is provided for the

connection of dust extraction and col-

lecting equipment, ensure these are

connected and properly used.

• Do not abuse the cord. Never

yank the cord do disconnect it from the

socket. Keep the cord away from heat,

oil and sham edges.

• Secure work. Where possible use

clamps or a vice to hold the work. It is

safer than using your hand.

• Do not overreach. Keep proper

footing and balance at all times.

This enables better control of the power

tool in unexpected situations.

• Maintain tools with care.

Many accidents are caused by poorly

maintained power tools.

- Keep cutting tools sharp and clean

for better and safer performance.

- Follow instruction for lubricating and

changing accessories.

- Inspect tool cords periodically and if

damaged have them repaired by an

authorized service facility.

- Inspect extension cords periodically

and replace if damaged.

- Keep handles dry, clean and free

from oil and grease.

• Disconnect tools. When not in use,

before servicing and when changing

accessories disconnect tools from the

power supply.

Such preventive safety measures reduce

the risk of starting the power tool acci-

dentaIly.

• Remove adjusting keys and

wrenches. Form the habit of check-

ing to see that keys and adjusting

wrenches are removed from the tool

before turning it on. A wrench or a key

left attached to a rotating part of the

power tool may result in personal injury.

• Avoid unintentional starting.

Ensure switch is in “off” position when

plugging in.

• Use outdoor extension leads.

When the tool is used outdoors, use

only extension cords intended for out-

door use and so marked.

• Stay alert, watch what you are

doing and use common sense

when operating a power tool.

Do not use a power tool while you are

tired or under the inuence of drugs,

alcohol or medication. A moment of

inattention white operating power tools

may result in serious personal injury.

• Check damaged parts. This will

ensure that the safety of the power tool

is maintained.

- Before further use of tool, it should be

carefully checked to determine that it

will operate properly and perform its

intended function.

- Check for alignment of moving parts,

binding of moving parts, breakage of

parts, mounting and any other condi-

tions that may affect its operation.

- A guard or other part that is dam-

aged should be properly repaired or

replaced by an authorized service

centre unless otherwise indicated in

this instruction manual.

- Have defective switches replaced by

9

GB

an authorized service centre.

- Do not use the tool if the switch does

not turn it on and off.

There is a risk of injury.

• Warning.

The use of any accessory or attach-

ment other than one recommended in

this instruction manual may present a

risk of personal injury.

• Have your tool repaired by a

qualied person. This electric tool

complies with the relevant safety rules.

Repairs should only be carried out by

qualied persons using original spare

parts, otherwise this may result in con-

siderable danger to the user.

Further Safety Instructions

• Connect the device only to a power

point with a residual current protective

device (RCD) with a measured residual

current of not more than 30 mA.

• Keep the mains cable and extension

cable away from the grinding disk and

saw chain. In the event that it is dam-

aged or severed, immediately discon-

nect the plug from the socket.

Do not touch the cable before it has

been disconnected from the mains.

Risk of electric shock.

• The replacement of the plug or the con-

nection line must always be executed

by the manufacturer of the electric tool

or his/her customer service in order to

avoid any hazards.

• Only switch the device on once it is

safely xed to the worktop.

• For your own safety only use acces-

sories and attachments which were

stated in the operating instructions or

recommended or specied by the tool

manufacturer.

• Only use grinding tools recommended

by the manufacturer. Do not use any

saw blades. Ensure that the dimensions

match those of the device.

• Only use grinding discs where the

printed rotational speed is at least as

high as what has been specied on the

name plate of the device.

• Carry out a visual inspection of the

grinding disc before use. Do not use

any damaged or deformed grinding

discs. Replace any damaged or worn

grinding discs.

• Never operate the device without spark

protection or protective hoods.

Periodically readjust the spark protec-

tion in order to offset the wear and

tear of the grinding disc (distance max.

2mm).

• Replace the grinding disc if the spark

protection and the workpiece support

can no longer be readjusted to a dis-

tance of max. 2 mm at the latest.

• Make sure that the sparks produced by

grinding do not present a danger, e.g.

reach people or ignite ammable sub-

stances.

• Always wear safety goggles, safety

gloves, respiratory protection and ear

protection when grinding, brushing and

separating.

• Never keep the ngers between the

grinding disc and spark protection or in

close proximity to the protective hoods.

There is a risk of crushing.

• The rotating parts of the device cannot

be covered due to functional reasons.

Therefore, proceed cautiously and hold

the workpiece rmly in order to avoid

slipping which could cause your hands

to come into contact with the grinding

belt or grinding disc.

• The workpiece gets hot during grinding.

Do not touch the machined area, allow

it to cool down. There is a risk of burn-

10

GB

Assembly

Caution! Risk of injury!

- Ensure that you have sufcient

space in which to work, and that

you do not endanger other peo-

ple.

- Always fasten the device on to

the work surface with screws

featuring the sufcient length and

thickness in order to maintain

control of the device.

- All covers and protective devices

must be assembled properly be-

fore commissioning.

- Disconnect the mains plug before

changing the setting on the de-

vice.

Assemble/set spark

protection

1. Screw the spark protection (1)

using the adjusting screw (2) and

the nut (2a) on to the protective

hood (3).

To do so, you will need a screw-

driver and a ring spanner, used

to hold it in place.

2. Set the spark protection (1) with

the adjusting screw (2) so that the

distance between the grinding

disc (19) and the spark protection

is max. 2 mm (see small image).

Periodically readjust the spark pro-

tection in order to offset the wear

and tear of the grinding disc (dis-

tance max. 2 mm).

ing. Do not use coolants or the like.

• If you are tired or have consumed al-

cohol or tablets, do not work with the

device. Always have a break on time.

• Switch the device off and remove the

mains plug

- to loosen a blocked insertion tool,

- if the connection line is damaged or

entangled,

- in case of unusual sounds.

Residual risks

Even if properly operating and handling

this electric tool, some residual risks will

remain. Due to its construction and build,

this electric tool may present the following

hazards:

a) Lung damage, if suitable respiratory

protection is not worn.

b) Hearing damage, if suitable ear pro-

tection is not worn.

c) Damages to health due to

- touching the area of the grinding tool

which was not covered;

- the ejection of pieces from workpiece

or damaged grinding discs.

d) Damage to your health caused by

swinging your hands and arms when

operating the appliance for longer pe-

riods of time or if the unit is not held or

maintained properly.

Warning! During operation, this

electric tool generates an electro-

magnetic eld which, under certain

circumstances, may impair the

functionality of active or passive

medical implants. To reduce the risk

of serious or lethal injuries, we rec-

ommend that persons with medical

implants consult their doctor and the

manufacturer of their medical im-

plant before operating the machine.

11

GB

Assemble/set work-

piece supports

1. Screw the workpiece supports

(6/18) on to the device.

2 positions (see

A + B) are

possible for the tape loop.

2. To do so, use the screws

(5a/17a), washers (5b/17b),

toothed lock washer (5c/17c)

and star grip nuts (5/17) pro-

vided.

3. Set the workpiece support of the

grinding belt (19) with the star

grip nut (17) so that the distance

between the grinding belt (19)

and the workpiece support is

max. 2 mm (see small image).

Periodically readjust the workpiece

support in order to offset the wear

and tear of the grinding disc (dis-

tance max. 2 mm).

Screw device on to work-

bench

Screw the device onto the work-

bench with 4 screws and nuts.

Insert the screws through the 4 bore

holes (13) on the base of the de-

vice.

The screws and nuts required for as-

sembly are not part of the scope of

delivery.

Operation

Caution! Risk of injury!

- Always disconnect the plug from

the mains socket before working.

- Use only grinding disks and ac-

cessories recommended by the

manufacturer. The use of other in-

sertion tools and other accessories

may cause risk of injury.

- Only use grinding tools which

bear information about the manu-

facturer, type of binding, dimen-

sion and permitted number of

revolutions.

- Only use grinding discs where

the printed rotational speed is at

least as high as what has been

specied on the name plate of

the device.

- Do not use broken, cracked or

otherwise damaged grinding

disks.

- Never operate the device without

the visual protection disk.

- Always use protective goggles

even if you are protected against

sparks.

- Always inspect the grinding disc

before starting the device:

Check the distance between the

spark protection and grinding

disc as well as workpiece support

and grinding disc (distance maxi-

mum 2 mm).

- The grinding disc must be re-

placed once the spark protection

and workpiece support on the

grinding disc do not have dis-

tance of max. 2 mm.

- Switch on the equipment only

when it is safely installed on the

work surface.

12

GB

Keep your hands away from

the grinding disc and grind-

ing belt when the device is in

operation. Injury hazard!

Switching on and off

Ensure that the mains voltage

matches the specications on the

rating plate.

Connect the equipment to the mains.

1. To switch on, press the “I” On switch

and the device starts up (see

14a).

2. To switch off, press the “0” off switch

and the device switches off (see

14b).

After switching on the device, wait until the

device has reached its max. speed. Only

then must you start with the grinding.

The disk will continue to

run after the equipment is

switched off. There is a risk

of injury.

Test run:

Before starting work and after each

change of grinding disk, carry out a test

run of at least 60 seconds with no load.

Switch off the equipment immediately if the

disk runs lumpy, substantial vibrations oc-

cur, or abnormal noises are generated.

Grinding with the grinding

disc

The arrow on the protective hood

(

3) shows the direction of rota-

tion of the grinding disc.

• Place the workpiece on the workpiece

support (

18) and slowly bring it to

its desired angle on the grinding disc

(

19).

• Move the workpiece slightly from side

to side in order to achieve an optimal

grinding result. This way, the grinding

disc is worn uniformly. Occasionally,

allow the workpiece to cool down.

Tape loops

The arrow on the protective hood

(

9) shows the direction of rota-

tion of the grinding belt.

• Firmly hold the workpiece, do not exert

any strong force.

• Move the workpiece slightly from side

to side in order to avoid a one-sided

wear of the grinding belt.

• Always grind the pieces of wood in the

direction of the wood grain in order to

avoid chipping.

Change grinding belt

1. Loosen the 3 xing screws (11)

and hang out the grinding belt

cover (12).

2. Loosen the clamping screw (8) by

a few rotations.

3. Press the clamping lever (7) down-

wards and detract the grinding

belt (10).

4. Place the new grinding belt (10)

in the centre on the upper (20a)

and lower (20b) rollers and let go

of the clamping lever (7).

5. Tighten the clamping screw (8) and

mount the grinding belt cover (12).

Set the tape run:

6. Loosen the nut (21a) of the ad-

13

GB

justable screw (21) with a ring

spanner. The tape run accuracy is

set by the turning the adjustable

screw (21) with a screwdriver.

7. Check the tape run by manually

turning the grinding belt.

8. Re-tighten the nut (21a).

Change grinding disc

Information on replace-

ment:

• Never operate the device without

protective equipment.

• Ensure that the rotation speed

stated on the grinding disc (

19) is the same or higher than

the nominal rotation speed of the

device.

• Ensure that the grinding disc

dimensions match those of the

device.

• Only use awless grinding discs

(ringing test: when you strike the

grinding disc with a plastic ham-

mer, it results in a clear sound).

• Never re-drill a locating hole

which is too small to make it

larger.

• Never use separate bushings or

adapters in order to make grind-

ing discs whose hole is too large

t the device.

• Do not use any saw blades.

• To clamp the grinding tools only

use the clamping ange provid-

ed. The pads between the clamp-

ing ange and the grinding tools

must be made of elastic materials

e.g., rubber, soft cardboard etc.

• Always reassemble the device

completely after replacing the

grinding disc.

Switch the device off and remove

the mains plug.

Allow the device to cool down.

Wear protective gloves when

changing the grinding discs in or-

der to avoid cutting damages.

1. Remove the spark protection (

1) (see „Assemble/set spark pro-

tection).

2. Loosen the 3 xing screws (15)

and remove the grinding disc

cover (16).

3. Loosen the xing screws (11) and

remove the grinding belt cover

(12) (see „Changing the grinding

belt“).

4. Unscrew the grinding disc nut

(19a) in the clockwise direction,

by holding the nut of the opposite

roller of the grinding belt in place

(see small image).

5. Remove the clamping ange

(19b) and the grinding disc (19).

6. Set up the new grinding disc (19)

and the clamping ange and

manually screw the grinding disc

nut (19a) in the anti-clockwise

direction.

7. Screw the grinding disc cover

(16).

8. Set the spark protection (

1)

and the workpiece support (

18) so that the distance between

the grinding disc (19) is max.

2mm (see „Assembly“).

The grinding disc nut must not be

screwed too tightly in order to

avoid a breaking of the grinding

disc and nut.

14

GB

Test run:

Before starting work and after each

change of grinding disk, carry out a test

run of at least 60 seconds with no load.

Switch off the equipment immediately if the

disk runs lumpy, substantial vibrations oc-

cur, or abnormal noises are generated.

Cleaning and

maintenance

Disconnect the plug before adjust-

ment, maintenance or repair.

Have any work not described

in these instructions carried

out by a specialist workshop.

Use only original components.

Allow the equipment to cool

before carrying out any main-

tenance and cleaning work.

There is a risk of burns.

Before each use, check the equipment

for obvious defects such as loose, worn

or damaged components and check that

screws or other parts are sitting correctly.

In particular, check the grinding disk (

19). Replace damaged parts.

Cleaning

Do not use cleaning agents or sol-

vents. Chemical substances may

attack plastic parts of the equipment.

Never clean the equipment under

running water.

• Clean the equipment thoroughly after

each use.

• Clean the ventilation openings and the

surface of the equipment with a brush

or cloth.

Maintenance

• The equipment is maintenance free.

Storage

• Store the appliance in a dry place well

out of reach of children.

• Grinding disks must be stored dry and

upright and are not to be stacked.

Waste disposal and en-

vironmental protection

Be environmentally friendly. Return the

tool, accessories and packaging to a recy-

cling centre when you have nished with

them.

Machines are not to be place with

domestic waste.

Hand over the device at an utilization loca-

tion. The plastic and metal parts employed

can be separated out into pure materials

and recycling can be implemented. Ask

your Service Center about this. Defective

units returned to us will be disposed of for

free.

15

GB

Replacement parts/accessories

Spare parts and accessories can be obtained at

www.grizzly-service.eu

If you do not have internet access, please contact the Service Centre via telephone

(see “Service-Center” page 18). Please have the order number mentioned below ready.

Position Position Description Order

Instruction Exploded number

manual drawing

1,2 Set 3 Spark protection with adjusting screw 91103042

10 35 Grinding belt 91103044

Grinding belt, pack of 5 91103046

14 Set 2 On/off-switch 91103041

19 62 Grinding disk 91103043

19a,19b Set 1 Grinding disk nut and clamping ange 91103040

16

GB

Trouble Shooting

Always disconnect the plug from the mains socket before working.

Danger of electric shock.

Problem Possible Cause Error correction

Device doesn‘t start

Mains voltage missing

Main circuit breaker is tripped

Check the socket, mains cable,

line, mains plug, repairs to be

carried out by qualied electri-

cian if necessary, check main

circuit breaker.

On/off switch (

14) may be

defective

Repair by Customer Care

Engine faulty

Grinding tools do

not move although

the engine is run-

ning

Grinding disc nut (

19a)

loose

Tighten grinding disc nut (see

„Changing the grinding disc“)

Grinding belt (

10) loose

Increase grinding belt tension

(see „Changing the grinding

belt“)

Drive is blocked

Grinding belt (

10) block-

ing drive

Re-mount grinding belt (see

„Changing the grinding belt“)

Workpiece, remaining work-

pieces or remaining grinding

tools block drive

Remove blockages

Engine is slower

and stops

Device is overloaded through

workpiece

Reduce pressure on grinding tool

Workpiece unsuitable

Grinding disc does

not rotate smoothly,

abnormal noises

can be heard

Grinding disc nut (

19a)

loose

Tighten grinding disc nut (see

„Changing the grinding disc“)

Grinding disc (

19) faulty

Change grinding disc

Spark protection (1) or work-

piece support (

6/18) set

incorrectly

Set spark protection or work-

piece support (see „Assembly“)

Bad grinding out-

put

Grinding belt (

10) worn

Change grinding belt

17

GB

Guarantee

Dear Customer, this equipment is provided

with a 3-year guarantee from the date of

purchase. In case of defects, you have stat-

utory rights against the seller of the prod-

uct. These statutory rights are not restricted

by our guarantee presented below.

Terms of Guarantee

The term of the guarantee begins on the

date of purchase. Please retain the original

receipt. This document is required as proof

of purchase.

If a material or manufacturing defect occurs

within three years of the date of purchase

of this product, we will repair or replace –

at our choice – the product for you free of

charge. This guarantee requires the defec-

tive equipment and proof of purchase to be

presented within the three-year period with

a brief written description of what consti-

tutes the defect and when it occurred.

If the defect is covered by our guarantee, you

will receive either the repaired product or a

new product. No new guarantee period be-

gins on repair or replacement of the product.

Guarantee Period and Statutory

Claims for Defects

The guarantee period is not extended by

the guarantee service. This also applies for

replaced or repaired parts. Any damages

and defects already present at the time of

purchase must be reported immediately af-

ter unpacking. Repairs arising after expiry

of the guarantee period are chargeable.

Guarantee Cover

The equipment has been carefully produced

in accordance with strict quality guidelines

and conscientiously checked prior to delivery.

The guarantee applies for all material and

manufacturing defects. This guarantee

does not extend to cover product parts

that are subject to normal wear and may

therefore be considered as wearing parts

(e.g. grinding disks, carbon brushes, stop-

per, protective screen) or to cover damage

to breakable parts (e.g. switches, batteries,

or parts made of glass).

This guarantee shall be invalid if the prod-

uct has been damaged, used incorrectly or

not maintained. Precise adherence to all of

the instructions specied in the operating

manual is required for proper use of the

product. Intended uses and actions against

which the operating manual advises or

warns must be categorically avoided.

The product is designed only for private and

not commercial use. The guarantee will be

invalidated in case of misuse or improper han-

dling, use of force, or interventions not under-

taken by our authorised service branch.

Processing in Case of Guarantee

To ensure quick handling of you issue,

please follow the following directions:

• Please have the receipt and identica-

tion number (IAN 113076) ready as

proof of purchase for all enquiries.

• Please nd the item number on the rat-

ing plate.

• Should functional errors or other de-

fects occur, please initially contact the

service department specied below by

telephone or by e-mail. You will then

receive further information on the pro-

cessing of your complaint.

• After consultation with our customer

service, a product recorded as defective

can be sent postage paid to the service

address communicated to you, with the

proof of purchase (receipt) and speci-

cation of what constitutes the defect

and when it occurred. In order to avoid

18

GB

acceptance problems and additional

costs, please be sure to use only the ad-

dress communicated to you. Ensure that

the consignment is not sent carriage

forward or by bulky goods, express or

other special freight. Please send the

equipment inc. all accessories supplied

at the time of purchase and ensure ad-

equate, safe transport packaging.

Repair Service

For a charge, repairs not covered by the

guarantee can be carried out by our ser-

vice branch, which will be happy to issue

a cost estimate for you. We can handle

only equipment that has been sent with ad-

equate packaging and postage.

Attention: Please send your equipment to

our service branch in clean condition and

with an indication of the defect.

Equipment sent carriage forward or by

bulky goods, express or other special

freight will not be accepted.

We will dispose of your defective devices

free of charge when you send them to us.

Service-Center

Service Great Britain

Tel.: 0871 5000 720

(£ 0.10/Min.)

E-Mail: [email protected]

IAN 113076

Importer

Please note that the following address is

not a service address. Please initially con-

tact the service centre specied above.

Grizzly Tools GmbH & Co. KG

Stockstädter Straße 20

D-63762 Großostheim

Germany

www.grizzly-service.eu

19

PL

Wstęp

Gratulujemy zakupu nowego urządzenia.

Zdecydowali się Państwo na zakup warto-

ściowego produktu.

Niniejsze urządzenie sprawdzono w trak-

cie produkcji pod kątem jakości, a także

dokonano jego kontroli ostatecznej. W ten

sposób zapewniona jest jego sprawność.

Nie da się wykluczyć tego, że w pojedyn-

czych przypadkach w urządzeniu lub przy

nim wzgl. w wężach mogą się znaleźć

pozostałości wody lub smaru. Nie jest to

brakiem ani uszkodzeniem, czy powodem

do troski o urządzenie.

Instrukcja obsługi jest częścią skła-

dową produktu. Zawiera ona waż-

ne wskazówki dotyczące bezpie-

czeństwa, eksploatacji i utylizacji.

Przed rozpoczęciem użytkowania

produktu należy się zapoznać ze

wszystkimi wskazówkami dotyczą-

cymi obsługi i bezpieczeństwa.

Produkt należy użytkować tylko

zgodnie z opisem i podanym prze-

znaczeniem. Instrukcję należy prze-

chowywać starannie, a w przypad-

ku przekazania produktu osobom

trzecim należy dostarczyć nabywcy

kompletną dokumentację.

Przeznaczenie

Stacjonarna szlierka taśmowa jest prze-

znaczona do wstępnego i właściwego

szlifowania metalu, drewna i tworzyw

sztucznych. Urządzenie nadaje się do

okrawania, odrdzewiania i szlifowania.

Urządzenie nie nadaje się do wszelkich

innych rodzajów zastosowań (np. do szli-

fowania z użyciem nieodpowiednich na-

rzędzi szlierskich, szlifowania z użyciem

chłodziwa, szlifowania materiałów niebez-

Spis tresci

Wstęp ........................................ 19

Przeznaczenie ............................ 19

Opis ogólny ............................... 20

Zawartość opakowania ................... 20

Opis działania ............................... 20

Przegląd ........................................ 20

Dane techniczne ......................... 21

Zasady bezpieczeństwa ............. 21

Symbole i piktogramy ...................... 22

Ogólne zasady bezpieczeństwa ....... 22

Dalsze zasady bezpieczeństwa ........ 24

Zagrożenia ogólne.......................... 26

Montaż ......................................26

Montaż i regulacja osłony

przeciwiskrowej .............................. 26

Montaż i regulacja uchwytów do

mocowania obrabianego materiału ... 27

Przykręcanie urządzenia na stole

roboczym ....................................... 27

Obsługa.....................................27

Włączanie i wyłączanie .................. 28

Szlifowanie z tarczą szlierską ......... 28

Szlifowanie taśmą szlierską ............ 28

Wymiana taśmy szlierskiej ............. 28

Wymiana tarczy szlierskiej ............. 29

Oczyszczanie i konserwacja .......30

Oczyszczanie ................................ 30

Konserwacja .................................. 31

Przechowywanie urządzenia .....31

Usuwanie i ochrona środowiska ..31

Części zamienne/Akcesoria ........ 31

Poszukiwanie błędów ................32

Gwarancja .................................33

Serwis naprawczy .....................34

Service-Center ............................34

Importer .................................... 34

Tłumaczenie oryginalnej

deklaracji zgodności WE............. 112

Rysunek samorozwijający .......117

20

PL

piecznych dla zdrowia, np. azbestu).

Urządzenie jest przeznaczone do amator-

skich prac w gospodarstwie domowym.

Nie jest ono przeznaczone do stałego sto-

sowania w celach zarobkowych.

Urządzenie może być używane tylko

przez osoby dorosłe. Osoby młodociane

powyżej 16 roku życia mogą używać

urządzenia tylko pod nadzorem.

Producent nie odpowiada za szkody wy-

wołane niezgodnym z przeznaczeniem

użytkowaniem lub nieprawidłową obsługą

urządzenia.

Opis ogólny

Ilustracje znajdują się na

okładce przedniej i tylnej.

Zawartość opakowania

Rozpakuj urządzenie i sprawdź, czy jest

ono kompletne. Prawidłowo posegreguj i

usuń materiały opakowania.

- Urządzenie

- Przezroczysta osłona przeciwiskrowa

(

1)

- Śruba regulacyjna osłony przeciwiskro-

wej (

2)(1 wkręt z rowkiem krzyżo-

wym z podkładką sprężystą i podkład-

ką zwykłą oraz nakrętką)

- 2 uchwyty do mocowania obrabianego

materiału (

6/18) z materiałem mon-

tażowym (2 nakrętki gwiazdkowe (

5/17), 2 śruby, 2 podkładki,

2 podkładki zębate)

- Instrukcja obsługi

Opis działania

Stacjonarna szlierka taśmowa jest urzą-

dzeniem łączonym, wyposażonym w tar-

czę i regulowaną taśmę szlierską. W celu

ochrony użytkownika urządzenie posiada

osłonę przeciwiskrową i osłony ochronne.

Funkcje elementów urządzenia są podane

w poniższym opisie.

Przegląd

1 Osłona przeciwiskrowa (dwuczę-

ściowa)

2 Śruba regulacyjna osłony prze-

ciwiskrowej

3 Osłona ochronna tarczy szlier-

skiej

4 Obudowa silnika

5 Nakrętka gwiazdkowa do monta-

żu uchwytu obrabianego materia-

łu przy taśmie szlierskiej

6 Uchwyt obrabianego materiału

dla taśmy szlierskiej

7 Dźwignia mocowania taśmy szli-

erskiej

8 Śruba mocująca górny krążek

taśmy

9 Osłona taśmy szlierskiej

10 Taśma szlierska

11 Śruby mocujące osłonę taśmy

szlierskiej

12 Osłona taśmy szlierskiej

13 Otwory do montażu na stole

14 Włącznik/wyłącznik

14a Włącznik

14b Wyłącznik

15 Śruby mocujące osłonę tarczy

szlierskiej

16 Osłona tarczy szlierskiej

17 Nakrętka gwiazdkowa do mon-

tażu i regulacji uchwytu obra-

bianego materiału przy tarczy

szlierskiej

18 Uchwyt obrabianego materiału

dla tarczy szlierskiej

19 Tarcza szlierska

20 Krążek toczny górny (a) i dolny

(b)

21 Śruba regulacji biegu taśmy

Stránka sa načítava ...

Parkside 113076 Translation Of The Original Instructions

Táto príručka je tiež vhodná pre

Parkside 113076 Translation Of The Original Instructions

V iných jazykoch

Súvisiace články

Ďalšie dokumenty