Sencor SDV 7406H Používateľská príručka

Kategória
DVD prehrávače
Typ
Používateľská príručka
DVD PLAYER
SDV 7406H
USER'S MANUAL
EN
SDV 7406H Sencor EN CZ SK HU PL.indb EN1 5.5.2015 11:00:30
SDV 7406H Sencor EN CZ SK HU PL.indb EN2 5.5.2015 11:00:37
EN 1
EN
Revision 05/2015Copyright © 2015, Fast ČR, a. s.
Contents
BEFORE STARTING TO OPERATE THIS PRODUCT, READ CAREFULLY THIS
INSTRUCTION MANUAL. STORE IT FOR LATER REFERENCE. NOTE THE MODEL
NUMBER AND THE SERIAL NUMBER. LOOK AT THE LABEL ON THE BACK COVER
AND PASS THE INFORMATION PROVIDED THERE TO YOUR DEALER IN CASE THAT
YOU WOULD NEED SERVICING.
Contents
1. Important safety instructions .........................................................................................................2
2. Features ............................................................................................................................................. 6
3. Device .................................................................................................................................................7
3.1. Front panel ................................................................................................................................7
3.2. Rear panel .................................................................................................................................7
4. Remote controller .............................................................................................................................8
5. Connections .....................................................................................................................................10
5.1. Connecting the video system .............................................................................................10
5.2. Connecting the audio system.............................................................................................. 11
6. System setup .................................................................................................................................. 13
6.1. Menu control ........................................................................................................................... 13
6.2. GENERAL SETUP ................................................................................................................. 13
6.3. AUDIO SETUP PAGE ........................................................................................................... 14
6.4. VIDEO SETUP PAGE ............................................................................................................16
6.5. PRE-SET PAGE.......................................................................................................................17
6.6. PASSWORD SETUP PAGE ................................................................................................ 18
7. Playback ...........................................................................................................................................19
7.1. PLAYBACK FROM DISC ......................................................................................................19
7.2. PLAYBACK FROM USB .....................................................................................................19
7.3. PLAYBACK FROM MP3/MPEG4 DISCS .........................................................................19
8. Troubleshooting............................................................................................................................... 21
9. Technical specifi cations ............................................................................................................... 23
SDV 7406H Sencor EN CZ SK HU PL.indb 1 5.5.2015 11:00:37
2 EN
EN
Revision 05/2015Copyright © 2015, Fast ČR, a. s.
Important safety instructions
1. Important safety instructions
If you want to use the product properly, read the manual carefully and keep it for future
reference.
General safety instructions
Read these instructions. Keep the manual in asafe place in case you want to consult
it in the future. If you will sell or give it to athird party, pass with the device the
manual as well.
Follow this manual and the instructions inside.
Heed all warnings.
Follow all instructions.
Use only the attachments and accessories specifi ed by the manufacturer.
You must not put an open fl ame on the device, e.g. aburning candle.
Use the device in temperate climate.
Under no circumstances are the manufacturer or vendor liable for any direct or
indirect damage caused by the failure to observe the instructions for installation,
confi guration, operation, treatment and cleaning of this device included in this
manual.
Protect the device against impacts, falls, blows, shocks, vibration, moisture and dust.
Prior to granting children consent to use the device, they shall become familiar with
the proper and safe use of the player, corresponding to their age.
Installation, control
Install the device according to the instructions in the manual.
Leave free space around the device, it is necessary for proper air circulation. It helps
to dissipate the heat generated by the operation of the device. By covering the air
vents of the cabinet, you risk overheating and damage of the device. It is important
to ensure that ventilation of the device is not prevented by covering the ventilation
openings with e. g. newspaper, tablecloth, drapes, etc. Follow the installation
instructions in the manual.
Do not install the device in direct sunlight, or close to heat sources, like radiators,
heat exchangers, stoves or other appliances (including amplifi ers) producing heat.
High temperatures shorten the life of the electronic components of the device
signifi cantly. Do not use and do not leave the device near an open fi re.
The device must not be exposed to dripping or running water and you must not place
upon it objects fi lled with liquid, e.g. vases. Protect the device against becoming wet,
sprayed on or poured on by any liquid, do not leave or install the device outdoors. Do
not use the device outdoors. You risk electric shock or fi re by not adhering to these
instructions.
Do not use the device close to water.
Do not try to defeat the purpose of the polarized plug. If you cannot fi t the plug in the
outlet, contact an electrician to replace the obsolete outlet.
Before connecting the unit to awall outlet, fi rst make sure that the voltage in your AC
outlet matches the voltage on the on the device type label.
SDV 7406H Sencor EN CZ SK HU PL.indb 2 5.5.2015 11:00:37
EN 3
EN
Revision 05/2015Copyright © 2015, Fast ČR, a. s.
Important safety instructions
Make sure that the power cable is not stepped on or pinched, especially close to
the plug, the outlet and at the point where it leaves the unit. The plug is used as
adisconnecting device and must be easily accessible.
Remember, before you disconnect the power cord when you power the device,
always disconnect the plug from the wall outlet.
Disconnect the power cord from the power outlet during thunderstorms, or when not
in use for alonger period of time.
Avoid carrying the device from acool environment into awarm environment or vice
versa, or operating the device in amoist environment. Air moisture may condense in
some areas within the device case and may cause the device to become temporarily
inoperable. In this case, leave the device in awarm and well-ventilated area and
leave for 1–2 hours until the moisture evaporates. The device can be normally used
again. Be especially cautious when using the device for the fi rst time during acool
season immediately after purchasing.
Service and maintenance
To avoid risks of electric shock or fi re, do not remove the device from the case – the
case does not contain components that the user could repair or adjust without the
necessary equipment and qualifi cation. Refer to aprofessional service centre if your
device requires service.
In the event of any unusual occurrences during the use of the device, e.g. smelling
the characteristic smell of burning insulation or even seeing asmoke, turn the device
off immediately, disconnect the power supply and wait with continuing use of the
device until you learn the result of its inspection by the service personnel.
Leave all service to qualifi ed service personnel. Service is necessary when the device
is damaged in any way, for example in case of damage to the power cord, spilling
liquid on the device, intrusion of foreign objects into the device, when the device is
exposed to rain or moisture, if the device does not function in the usual manner or if
it fell.
Clean the device with adry cloth only.
Remote control and batteries
Do not expose the remote control and batteries to direct sunlight or heat sources,
such as radiators, heat exchangers, ovens or other appliances (including amplifi ers)
producing heat. Do not use and do not leave the device near an open fi re.
Remote control and batteries may not be exposed to dripping or running water and
no objects fi lled with water should be placed on them, for example, vases. Protect
them from getting wet, from being sprayed or from spilled liquid of any kind. Do not
use outdoors. Failure to do so, risks damage to the remote control or batteries.
Do not use the device close to water.
It is necessary to consider the environmental impact when liquidating the batteries.
Using the batteries incorrectly can result in leakage and corrosion. Follow the
following instructions to ensure proper remote control operation:
Do not insert the batteries in the wrong direction.
Do not charge, heat, open or short the batteries.
SDV 7406H Sencor EN CZ SK HU PL.indb 3 5.5.2015 11:00:37
4 EN
EN
Revision 05/2015Copyright © 2015, Fast ČR, a. s.
Important safety instructions
Do not throw batteries into afi re.
Do not leave dead batteries in the remote controller.
Do not combine various types of batteries or old and new batteries.
If you do not use the remote controller for alonger period of time, remove the
batteries to prevent damaging the remote controller by the batteries leaking out.
If the remote control does not work properly or its effective range decreases,
change all the batteries for new ones.
If there is an electrolyte leakage from the batteries, have the remote control
serviced by an authorized technician.
NOTICE
To prevent risk of fi re or electric shock, do not expose the device to rain or
moisture.
NOTICE
The batteries must not be exposed to excessive heat, for example sunlight, fi re,
etc.
The symbol warns that the inside of this unit contains dangerous voltage,
which poses arisk of electric shock.
The symbol indicates important operating and service instructions in the
documentation accompanying the device.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
CAUTION
To reduce the risk of electric shock, do not open the cover. Refer to qualifi ed
service technicians for repair work.
DVD player
This DVD player uses alaser system. To learn to use this device properly, please, read
this manual and keep it for later reference. The opening for discs is located on the side
for safety reasons, to prevent exposure to laser radiation. Do not try to change or alter the
opening for discs in any way. When inserting the disc into the player or during the replay,
do not look into the opening for discs. Visible laser radiation could be emitted. Do not look
at the laser beams.
SDV 7406H Sencor EN CZ SK HU PL.indb 4 5.5.2015 11:00:37
EN 5
EN
Revision 05/2015Copyright © 2015, Fast ČR, a. s.
Important safety instructions
CLASS 1
LASER PRODUCT
NOTICE:
THIS DVD PLAYER IS ACLASS 1 LASER PRODUCT. USING CONTROLS, OR
SETUP OR PROCEDURES NOT LISTED IN THIS MANUAL MAY RESULT IN
EXPOSURE OF PEOPLE TO DANGEROUS RADIATION. SINCE THE LASER
BEAM USED IN THIS DEVICE IS HARMFUL TO HUMAN EYESIGHT, DO NOT
TRY DISASSEMBLE THE PLAYER. ALL SERVICE SHOULD BE DONE BY
QUALIFIED PERSONEL.
WARNING
UNDER THE FCC REGULATIONS, ANY CHANGE OR ALTERATION NOT
EXPRESSLY APPROVED BY THE MANUFACTURER OR BY HIS AUTHORIZED
REPRESENTATIVE MAY LEAD TO CANCELLATION OF THE RIGHT OF THE
USER TO USE THE DEVICE.
This device is equipped with anti-copying technology, protected by USA patents and other
rights for the protection of the intellectual property of ROVI. Reverse engineering and
disassembly is prohibited.
Concerning the USB connector:
USB memory device must be plugged directly into the device.
Do not use aUSB extension cable, it might cause data transfer failure or interference.
Electrostatic discharges may cause malfunction. In this case, the user must restart
the device. The player can play similar types of fi les and formats from the USB
device like from the disc. Before you use USB memory device try its communication
function with the device and the speed of reading data. Remember that reading of
data via external connector can be slower and the fi les with high data fl ow may not
be played correctly.
For maximum reading speed, we recommend to keep the disc space defragmented.
Use fi le system FAT32, single partition, no protection. If the reading of the memory
device is not smooth, it can lead to undesirable effects, such as losing part of the
picture (blocking) or all of it, sound problems and in extreme case stopping the
reading operation. Unexpected behaviour of the memory device or the presence of
viruses or other malware, may cause stopping of functioning of the device and need
to be restarted.
The USB connector is of standard type and cannot supply power to highly powered
USB devices (e. g. hard discs HDD). Use devices with their own power supply and
power them from their own power.
The device was designed for maximum compatibility with memory devices. Due
to the wide range of the devices on the market, it is not possible to guarantee
compatibility with every USB device. In case of diffi culties, try to format the memory
device directly inside the device. If diffi culties persist, use another memory device.
SDV 7406H Sencor EN CZ SK HU PL.indb 5 5.5.2015 11:00:38
6 EN
EN
Revision 05/2015Copyright © 2015, Fast ČR, a. s.
Features
2. Features
Integrated digital audio decoder compatible with Dolby Digital, MPEG, PCM etc.
96kHz/24bit audio digital processor.
Intelligent software update.
Component high defi nition video out.
Coaxial digital audio out
Multimedia USB port.
Compatible with DVD, VCD, DVCD, CD, DVD+R/RW, DVD-R/RW, MP3, MPEG4,
DIVX, Kodak Picture CD etc. Highly integrated servo system, decoding to single-chip
technology, high reliability and stability and top class error correction.
Accessories
User's manual Remote controller A/V cable
Compatible discs and media:
Types of discs Symbol Contents
DVD
Audio + Video
MP3
Sound
Video-CD
(VCD)
Audio + Video
CD-DA
Audio
Picture CD
JPEG Photo CD
Kodak Picture CD
Electronic photos
MPEG-4
V I D E O
Audio + Video
SDV 7406H Sencor EN CZ SK HU PL.indb 6 5.5.2015 11:00:38
EN 7
EN
Revision 05/2015Copyright © 2015, Fast ČR, a. s.
Device
3. Device
3.1. Front panel
1. Off
2. USB port
3. OPEN/CLOSE button
4. PLAY button (
B
)
5. STOP button (
x
)
3.2. Rear panel
1. HDMI output
2. Mixed L/R audio out
3. Component video out
4. Coaxial digital out
5. Composite video out
6. S-video output
SDV 7406H Sencor EN CZ SK HU PL.indb 7 5.5.2015 11:00:39
8 EN
EN
Revision 05/2015Copyright © 2015, Fast ČR, a. s.
Remote controller
4. Remote controller
1. OPEN/CLOSE
2. VOLUME +/-
3. SUBTITLE
4. AUDIO
5. PROG
6. SLOW
7. OSD
8. A-B
9. SETUP
10. UP
11. LEFT
12. SCORE
13. DVD/USB
14. P/N
15. ANGLE
16. NUMERICAL BUTTONS
17. REV/FWD
18. STOP
19. RESET
20. BACK
21. NEXT
22. TITLE
23. RIGHT
24. PBC
25. DOWN
26. V-MODE
27. ZOOM
28. MUTE
29. L/R
30. GOTO
Remote controller use
Insert two AAA / 1.5 Vbatteries into the controller. Aim the remote controller directly at
the sensor on the front panel. The remote controller works at adistance of up to 8 metres
from the sensor and at an angle of about 30 degrees left and right.
SDV 7406H Sencor EN CZ SK HU PL.indb 8 5.5.2015 11:00:39
EN 9
EN
Revision 05/2015Copyright © 2015, Fast ČR, a. s.
Remote controller
Inserting batteries
Remove the cover of the
battery compartment
on the back side of the
controller.
Insert the batteries into the
battery compartment. Mind the
proper battery polarity according
to the + and - symbols shown
inside the compartment. Place the cover back on.
SDV 7406H Sencor EN CZ SK HU PL.indb 9 5.5.2015 11:00:39
10 EN
EN
Revision 05/2015Copyright © 2015, Fast ČR, a. s.
Connections
5. Connections
5.1. Connecting the video system
The following video outputs are available with the device.
Composite video
Use the yellow AV cable plug to connect the composite video output of the device to the
TV/monitor input.
S-Video
Use the S-Video cable to connect the S-Video output of the device to the TV/monitor
S-Video input.
Component video
Use the 3-wire Video cable to connect the component outputs of the device to the
corresponding TV/monitor inputs.
TV/monitor video in
DVD player video out
Component video in
Component video out
Composite video in and
S-Video in
Composite video out and
S-Video out
SDV 7406H Sencor EN CZ SK HU PL.indb 10 5.5.2015 11:00:39
EN 11
EN
Revision 05/2015Copyright © 2015, Fast ČR, a. s.
Connections
Notes:
Component is the best of the video outputs above, S-VIDEO out is good and composite
video output is standard.
Use the best video signal connection available.
Do not perform all connections at the same time, otherwise the quality of the
generated picture will be infl uenced.
The player generates the corresponding video output only when the video settings
correspond to the video system connection used (see Video output setup in chapter
System setup).
5.2. Connecting the audio system
There are two types audio out systems. The analogue and digital audio out system.
The analogue audio out system includes atwo-channel stereo output. The digital audio
out system contains acoaxial output.
Stereo out
Use the pair of audio cables (white for left, red for right channel) to connect the stereo
audio outputs of the device to the TV or amplifi er stereo outputs.
Digital output (coaxial)
Use the coaxial cable to connect the coaxial output of the device to the coaxial input of
the amplifi er/receiver equipped with its own digital decoder. The player only transfers
audio from the disc/media to be processed via an external device, including for example
multi-channel audio.
SDV 7406H Sencor EN CZ SK HU PL.indb 11 5.5.2015 11:00:40
12 EN
EN
Revision 05/2015Copyright © 2015, Fast ČR, a. s.
Connections
TV/monitor/amplifi er audio in
DVD audio out
2 channel audio in
2 channel audio out
Digital audio in
Digital audio out
Note:
The audio setup should correspond to the actual audio system connection. Please
check. Follow the instructions specifi ed in the Audio setup section of chapter System
setup.
SDV 7406H Sencor EN CZ SK HU PL.indb 12 5.5.2015 11:00:40
EN 13
EN
Revision 05/2015Copyright © 2015, Fast ČR, a. s.
System setup
6. System setup
6.1. Menu control
1. Press the [SETUP] button to display the setup menu.
2. Press [ ]/[ ] to select an item. The sub-menu for the selected item will
immediately appear below.
3. Press [ ] to enter the sub-menu.
4. Press [ ]/[ ] to select the sub-menu item you wish to setup, and press [ENTER]/
[ ] to enter setup. Press [ ]/[ ] to select an option and confi rm with [ENTER] or
cancel by pressing [ ].
5. You can then press [ ]/[ ] and continue in the setup of additional items from this
sub-menu.
6. Press [ ] to return to the parent menu.
7. Press the [SETUP] button again to exit the setup menu.
Note:
The item you are currently setting is highlighted green. The current value is brown. If
the value is correct and does not require adjusting, you do not have to enter the sub-
menu ( ) and you can continue on to the next item ( / ).
6.2. GENERAL SETUP
6.2.1. TV DISPLAY
If the device is connected to astandard TV, select 4:3 PANSCAN or 4:3 LETTERBOX.
Apicture with a4:3 aspect ratio is displayed full screen with the native aspect ratio.
4:3 PANSCAN: Awidescreen picture is displayed on the screen with the native aspect
ratio, while part of the picture will be cropped on the left and right.
4:3 LETTER BOX: Awidescreen picture is displayed on the screen with the native aspect
ratio with black strips above and below the picture.
If the device is connected to awidescreen TV, select 16:9.
16: 9: Awidescreen picture is displayed on the screen with the native aspect ratio, while
the picture with a4:3 aspect ratio is expanded to width in order to fi ll the screen.
6.2.2. ANGLE SYMBOL
Set this item to ON. When adisc with multiple camera angles is played, the angle
symbol will appear on the screen. You can then watch the video from various camera
angles after pressing the [ANGLE] button on the remote controller.
Turn off the function by setting the item to OFF.
Note:
This function can only be used for discs coded with multiple camera angles.
SDV 7406H Sencor EN CZ SK HU PL.indb 13 5.5.2015 11:00:40
14 EN
EN
Revision 05/2015Copyright © 2015, Fast ČR, a. s.
System setup
6.2.3. SETUP LANGUAGE (On-screen menu language)
This item is used to set the on-screen menu language.
SUBTITLES/CAPTIONS
Subtitles (for DVD) will be displayed when this item is set to ON. Subtitles are hidden
when set to OFF.
Subtitles can be displayed or hidden by pressing [SUBTITLE] on the remote controller.
Note:
This function can only be used for discs coded with subtitles.
6.2.4. SCREENSAVER
ON: If the screen is idle without movement, for example when disc playback is paused,
stopped, etc., the screensaver will appear on the screen after several minutes. Press any
button except for [STANDBY] to wake the screen up.
OFF: Disabling the screensaver function.
6.2.5. HDCD (High Defi nition Compatible Digital)
HDCD (High Defi nition Compatible Digital) is apatented coding/decoding process that
ensures the richest and highest detail of audio on CD discs coded in HDCD format. The
digital fi lter under this item can be set to 2X, 1X or OFF.
6.2.6. LAST MEMORY
ON: The player remembers the last playback time when the disc compartment is opened
during playback, paused playback, or playback is stopped completely. When the same
disc is inserted back into the device, playback will resume from the stored time.
OFF: Disabling the last memory function.
6.3. AUDIO SETUP PAGE
6.3.1. SPEAKER SETUP (ANALOGUE AUDIO)
DOWNMIX
LT/RT: Multi-channel audio is merged into the left and right channel and played via the
left and right front speaker.
STEREO: Astereo signal is selected from amulti-channel audio stream and played via
the left and right front speaker.
Note:
This function only relates to 5.1 channel discs coded in Dolby AC-3 format.
SDV 7406H Sencor EN CZ SK HU PL.indb 14 5.5.2015 11:00:40
EN 15
EN
Revision 05/2015Copyright © 2015, Fast ČR, a. s.
System setup
6.3.2. DIGITAL AUDIO SETUP
DIGITAL S/PDIF OUT
SPDIF/ OFF: Adigital audio signal will not be available. (Coaxial output off)
SPDIF/RAW: The digital audio signal input will be in raw format (as recorded on the disc,
for external processing).
SPDIF/PCM: The digital audio signal input will be in PCM format (linear audio, if
available).
6.3.3. KARAOKE SETUP
This item is available if the DIGITAL OUT item is set to SPDIF/PCM.
Select the sampling frequency for the digital audio output. The available options are 48
kHz and 96 kHz.
Note:
Some amplifi ers do not support 96kHz sampling, which has an effect on the coaxial
output.
6.3.4. CHANNEL DELAY
This item is used to set the delay of the centre speaker, rear speakers and subwoofer.
The delay is used to compensate the time difference in transmitting audio caused by the
difference in speaker distance from listeners.
Use the arrow keys [ ]/[ ] to select the centre speaker, subwoofer, left or right 3D
speaker.
Then use the arrow keys [ ]/[ ] to set the differences in distance.
6.3.5. EQUALIZER
AUDIO MODE
Select the mode that best fi ts your taste ROCK, POP, LIVE, DANCE, TECHNO, CLASSIC
or SOFT, or select NONE if you do not care to omit sound effects.
6.3.6. 3D PROCESSNG
REVERB MODE
Select the mode that best fi ts your taste CONCERT, LIVING ROOM, HALL, BATHROOM,
CAVE, ARENA or CHURCH, or select NORMAL to disable the reverb effect.
6.3.7. DOLBY DIGITAL SETTINGS
DUAL MONO
STEREO: The player transmits the audio signal of the left and right channel and played
via the left and right front speaker.
L-MONO: The player only transmits the audio signal of the left channel to the left and
right front speaker.
SDV 7406H Sencor EN CZ SK HU PL.indb 15 5.5.2015 11:00:40
16 EN
EN
Revision 05/2015Copyright © 2015, Fast ČR, a. s.
System setup
P-MONO: The player only transmits the audio signal of the right channel to the left and
right front speaker.
MIX- MONO: The player transmits the mean signal of the left and right channel to the left
and right front speaker.
Note:
This function only relates to 2 channel discs coded in Dolby AC-3 format.
6.3.8. DYNAMICS
When you are watching Dolby Digital fi lms with awide dynamic range at alow volume,
for example during the night, you can reduce the dynamics to avoid losing audio details
due to the low volume settings.
6.4. VIDEO SETUP PAGE
6.4.1. COMPONENT VIDEO OUT
Used to set the video output to YUV or S-Video, if the S-Video connection is used.
Note:
If the video settings differ from the physical connections, the resulting TV picture may
be of less quality. Press [V-MODE] on the remote controller repeatedly to switch to the
respective video output mode.
If the video setting differ from the actual video signal connected (with the exception to
composite videos), the picture may not be displayed on the TV or it may be of very
low quality. In such acase, the settings for this item shall be restored to ensure the
right video output mode or press [V-MODE] until the picture becomes normal.
6.4.2. RESOLUTION
For high defi nition compatible outputs (HDMI, component) you can select resolutions from
480/576i to 1080p.
NOTICE
See the TV manual to determine the highest supported resolution and do
not exceed this setting. Exceeding this setting could result in the picture
disappearing, or in rare cases, the TV could become damaged.
6.4.3. QUALITY SETUP
SHARPNESS
There are three available options under this item (HIGH, MEDIUM and LOW).
SDV 7406H Sencor EN CZ SK HU PL.indb 16 5.5.2015 11:00:40
EN 17
EN
Revision 05/2015Copyright © 2015, Fast ČR, a. s.
System setup
BRIGHTNESS, CONTRAST
Select one of the items, use the arrow buttons [ ]/[ ] to set the value and then confi rm
with [ENTER].
6.4.4. HDMI SETUP
HDMI
You can enable or disable the HDMI output.
6.4.5. AUDIO SOURCE (AUDIO)
HDMI audio can be set automatically according to the disc (AUTO) or forced by selecting
PCM linear audio (provided it is included on the disc).
6.5. PRE-SET PAGE
This item is available when there is not disc in the compartment, the compartment is
open or the disc in the compartment is stopped.
6.5.1. TV TYPE
This product supports NTSC (National Television System Committee) and PAL (Phase
Alternating Line) television broadcasting standards.
PAL: Select this mode if the connected TV uses the PAL system. The video signal of an
NTSC disc will be transmitted in PAL format.
AUTO: Select this mode if the connected TV uses multiple systems. The video signal
output format will correspond with the disc video signal.
NTSC: Select this mode if the connected TV uses the NTSC system. The video signal of
an PAL disc will be transmitted in NTSC format.
Note:
If the setup is incorrect, the picture quality will be of very low quality. In such cases,
adjust the settings for this item to eliminate the error.
6.5.2. AUDIO, SUBTITLES and DISC MENU
Select the desired language for audio, subtitles and disc menu under these items.
The audio language selection can also be set by pressing [AUDIO] and the subtitle
language can be set by pressing [SUBTITLE] on the remote controller.
Note:
If the selected language for the current disc being played is not available, the default
disc settings will remain selected.
SDV 7406H Sencor EN CZ SK HU PL.indb 17 5.5.2015 11:00:40
18 EN
EN
Revision 05/2015Copyright © 2015, Fast ČR, a. s.
System setup
6.5.3. PARENT LOCK
This item allows the user to set the maximum score for afi lm that can be watched. Films
with scores higher than the parent lock score cannot be watched. You must enter the right
password to reset the default settings. The default password is 0000.
Note:
This function is only available for discs with available parent lock.
6.6. PASSWORD SETUP PAGE
6.6.1. PASSWORD MODE
The password function can be enabled or disabled under this item. Apassword is used for
discs with adefi ned level of unsuitable content.
Note:
Prior to changing the settings for this item, you must enter the correct password and
confi rm by pressing [ENTER]. The default password is 136900.
6.6.2. PASSWORD
The password can be changed under this item. Enter the current password and then the
new password. You are required enter the new password again to rule out entering an
incorrect password.
6.6.3. DEFAULT SETTINGS
Use this function to restore all default settings with the exception of PARENT LOCK and
PASSWORD.
SDV 7406H Sencor EN CZ SK HU PL.indb 18 5.5.2015 11:00:40
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146

Sencor SDV 7406H Používateľská príručka

Kategória
DVD prehrávače
Typ
Používateľská príručka

V iných jazykoch