Parkside PWS 125 A1 ANGLE GRINDER Operation and Safety Notes

IAN 90983

ANGLE GRINDER PWS 125 A1

WINKELSCHLEIFER

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung

ANGLE GRINDER

Operation and Safety Notes

Translation of original operation manual

SZLIFIERKA KĄ TOW A

Wskazówki dotyczące obsługi i bezpieczeństwa

Tłumaczenie oryginalnej instrukcji obsługi

KOTNI bRuSILNIK

Navodila za upravljanje in varnostna opozorila

Prevod originalnega navodila za uporabo

ÚHLOV Á bRuSKA

Pokyny pro obsluhu a bezpečnostní pokyny

Překlad originálního provozního návodu

uHLOV Á bRÚSKA

Pokyny pre obsluhu a bezpečnostné pokyny

Preklad originálneho návodu na obsluhu

SAR OK CSISZOLÓ

Kezelési és biztonsági utalások

Az originál használati utasítás fordítása

GB Operation and Safety Notes Page 5

PL Wskazówki dotyczące obsługi i bezpieczeństwa Strona 19

HU Kezelési és biztonsági utalások Oldal 35

SI Navodila za upravljanje in varnostna opozorila Stran 49

CZ Pokyny pro obsluhu a bezpečnostní pokyny Strana 65

SK Pokyny pre obsluhu a bezpečnostné pokyny Strana 79

DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 93

Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the

device.

Przed przeczytaniem proszę rozłożyć obie strony z ilustracjami, a następnie proszę zapoznać się z wszy-

stkimi funkcjami urządzenia.

Olvasás előtt kattintson az ábrákat tartalmazó mindkét oldalra és végezetül ismerje meg a készülék minde-

gyik funkcióját.

Pred branjem obe strani s slikami odprite navzven in se nato seznanite z vsemi funkcijami naprave.

Před čtením si odklopte obě dvě strany s obrázky a potom se seznamte se všemi funkcemi přístroje.

Pred čítaním si odklopte obidve strany s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich anschließend

mit allen Funktionen des Gerätes vertraut.

A B

9

2

5

6

7

8

C D

6

11

1

3

4

10

E

F

G

5 GB

Table of contents

Introduction

Proper use ............................................................................................................................................Page 6

Features and equipment .....................................................................................................................Page 6

Included items .....................................................................................................................................Page 6

Technical information .......................................................................................................................... Page 6

General safety advice for electrical power tools

1. Workplace safety ...........................................................................................................................Page 7

2. Electrical safety ............................................................................................................................... Page 7

3. Personal safety ................................................................................................................................Page 7

4. Careful handling and use of electrical power tools .....................................................................Page 8

5. Service .............................................................................................................................................Page 8

Safety advice for all uses ....................................................................................................................Page 9

Safety advice relating to kickback .....................................................................................................Page 10

Special safety advice relating to grinding and disc-cutting ..............................................................Page 10

Further special safety advice for disc-cutting ..................................................................................... Page 11

Special safety advice for abrading using sandpaper ......................................................................Page 11

Special safety advice for polishing ....................................................................................................Page 11

Special safety advice for working with wire brushes ........................................................................Page 12

Safety advice for angle grinders ........................................................................................................Page 12

Advice on use ......................................................................................................................................Page 13

Use

Switching on and off ........................................................................................................................... Page 14

Setting the speed .................................................................................................................................Page 14

Changing a disc .................................................................................................................................. Page 15

Use of accessories

Cutting / roughing discs ......................................................................................................................Page 15

Flap discs for metal .............................................................................................................................Page 15

Other accessories ...............................................................................................................................Page 15

Adjusting the disc guard cover ...........................................................................................................Page 16

Using the auxiliary handle ..................................................................................................................Page 16

Maintenance and cleaning ............................................................................................... Page 16

Service ...............................................................................................................................................Page 17

Warranty .........................................................................................................................................Page 17

Disposal ............................................................................................................................................Page 17

Declaration of Conformity / Manufacturer..........................................................Page 18

6 GB

Introduction / General safety advice for electrical power tools

Introduction

Angle grinder PWS 125 A1

Grinding, roughing, cutting

Q

Introduction

We congratulate you on the purchase of your new

device. You have chosen a high quality product. The

instructions for use are part of the product. They

contain important information concerning safety,

use and disposal. Before using the product, please

familiarise yourself with all of the safety information

and instructions for use. Only use the unit as de

scribed

and for the speciﬁed applications. If you pass the

product on to anyone else, please ensure that you

also pass on all the documentation with it.

Q

Proper use

This tool is suitable for cutting, roughening and

brushing metal materials without the use of water.

Any other use or modiﬁcation to the device shall be

considered as improper use and could give rise to

considerable dangers. We will not accept liability

for loss or damage arising from improper use. The

device is not intended for commercial use.

Note: Slots cut in load-bearing walls must comply

with standard DIN 1053 Part 1 or the regulations

applicable in your country.

These instructions and advice must be observed.

Before you start a task, seek the advice of a com-

petent structural engineer, architect, or the relevant

site management staﬀ.

Q

Features and equipment

1

Safety lock-out

2

ON / OFF switch

3

Carbon brushes cover

4

Auxiliary handle

5

Adjustable disc guard

6

Clamping nut

7

Mounting spindle

8

Mounting ﬂange

9

Spindle lock button

10

Speed pre-selector wheel

11

Spanner (Fig. B)

Q

Included items

1 Angle grinder PWS 125 A1

1 Metal-cutting disc

1 Auxiliary handle

1 Disc guard cover

1 Spanner

1 Operating instructions

Q

Technical information

Rated input: 1200 W

Rated voltage: 230–240 V∼, 50 Hz

Rated no-load speed: n 12000 rpm

Variable rotation speed: 3000 to 12000 rpm

Spindle thread: M14

Protection class: II /

Noise and vibration data:

Measured values for noise are determined in accor-

dance with EN 60745. The A-weighted noise level

of the electrical power tool are typically:

Sound pressure level: 91 dB(A)

Sound power level: 102 dB(A)

Uncertainty K: 3 dB

Wear hearing protection!

Vibration total values determined

according to EN 60745:

Surface grinding:

Vibration emission value a

h, AG

= 13.431 m/s

2

,

Uncertainty K = 1.5 m/s

2

.

The vibration level speciﬁed in

these instructions was measured in accordance with

an EN 60745 standardised measurement process

and can be used to compare equipment. The vibra-

tion emission value speciﬁed can also serve as a

preliminary assessment of the exposure.

The vibration level will change according to the ap-

plication of the electrical tool an in some cases may

exceed the value speciﬁed in these instructions.

7 GB

Introduction / General safety advice for electrical power tools

Introduction

Regularly using the electric tool in such a way may

make it easy to underestimate the vibration.

Note: If you wish to make an accurate assessment

of the vibration loads experienced during a particular

period of working, you should also take into account

the intervening periods of time when the device is

switched oﬀ or is running but is not actually in use.

This can result in a much lower vibration load over

the whole of the period of working.

General safety advice for

electrical power tools

Read all the

safety advice and instructions!

Failure to observe the safety advice

and instructions may result in electric shock, ﬁre and /

or serious injury.

Keep all the safety advice and instructions

in a safe place for future reference!

The term “electrical tool” used in the safety advice

refers to electrical tools powered by mains electrici-

ty (by means of a mains lead) and electrical tools

powered by rechargeable batteries (without a

mains lead).

1. Workplace safety

a) Keep your working area clean and

well lit. Untidy or poorly lit working areas can

lead to accidents.

b) Do not work with the device in poten-

tially explosive environments in which

there are inflammable liquids, gases

or dusts. Electrical power tools create sparks,

which can ignite dusts or fumes.

c) Keep children and other people away

while you are operating the electrical

tool. Distractions can cause you to lose control

of the device.

2. Electrical safety

a)

The mains plug on the device must match

the mains socket. The plug must not be

modified in any way. Do not use an

adapter plug with devices fitted with

a protective earth. Unmodiﬁed plugs and

matching sockets reduce the risk of electric shock.

b) Avoid touching earthed surfaces such

as pipes, radiators, ovens and refrig-

erators with any part of your body.

There is an increased risk of electric shock if

your body is earthed.

c) Keep the device away from rain or

moisture. Water entering an electrical device

increases the risk of electric shock.

d) Do not use the mains lead for any pur-

pose for which it was not intended,

e.g.

to carry the device, to hang up the de-

vice or to pull the mains plug out of

the mains socket. Keep the mains lead

away from heat, oil, sharp edges or

moving parts of the device. Damaged

or tangled mains leads increase the risk of

electric shock.

e) When working outdoors with an

electrical power tool always use ex-

tension cables that are also approved

for use outdoors. The use of an extension

cable suitable for outdoor use reduces the risk

of electric shock.

f) Use a residual current device (RCD)

for protection if operating the electri-

cal power tool in a moist environment

is unavoidable. The use of an RCD reduces

the risk of electric shock.

3. Personal safety

a) Remain alert at all times, watch what

you are doing and always proceed

with caution. Do not use the device if

you are tired or under the influence of

drugs, alcohol or medication. One mo

ment

of carelessness when using the device can lead

to serious injury.

8 GB

General safety advice for electrical power tools

b) Wear personal protective equipment

and always wear safety glasses. The

wearing of personal protective equipment such

as dust masks, non-slip safety shoes, safety hel-

mets or ear protectors, appropriate to the type

of electrical power tool used and work under-

taken, reduces the risk of injury.

c) Avoid unintentional operation of the

device. Check that the electrical power

tool is switched off before you connect

it to the mains, pick it up or carry it.

Accidents can happen if you carry the device

with your ﬁnger on the ON / OFF switch or with

the device switched on.

d) Remove any setting tools or spanners

before you switch the device on. A tool

or spanner left attached to a rotating part of a

device can lead to injury.

e) Avoid placing your body in an unnat-

ural position. Keep proper footing and

balance at all times. By doing this you will

be in a better position to control the device in

unforeseen circumstances.

f) Wear suitable clothing. Do not wear

loose clothing or jewellery. Keep your

hair, clothing and gloves clear of mov-

ing parts. Loose clothing, jewellery or long

hair can become trapped in moving parts.

g) If vacuum dust extraction and collection

devices are fitted do not forget to

check

that they are properly connected and

correctly used. The use of these devices

reduces the hazard presented by dust.

4. Careful handling and use

of electrical power tools

a) Do not overload the device. Always

use an electrical power tool that is

intended for the task you are under-

taking. By using the right electrical power

tool for the job you will work more safely and

achieve a better result.

b) Do not use an electrical power tool if

its switch is defective. An electrical power

tool that can no longer be switched on and oﬀ

is dangerous and must be repaired.

c) Pull the mains plug from the socket

before you make any adjustments to

the device, change accessories or when

the device is put away. This precaution is

intended to prevent you from unintentionally

starting the device.

d) When not in use always ensure that

electrical power tools are kept out of

reach of children. Do not let anyone use

the device if he or she is not familiar

with it or has not read the instructions

and advice. Electrical power tools are dan-

gerous when they are used by inexperienced

people.

e) Look after the device carefully. Check

that moving parts are working prop-

erly and move freely. Check for any

parts that are broken or damaged

enough to detrimentally affect the

functioning of the device. Have dam-

aged parts repaired before you use

the device. Many accidents have their origins

in poorly maintained electrical power tools.

f) Keep cutting tools clean and sharp.

Carefully maintained cutting tools with sharp

cutting edges are less likely to jam and are

easier to control.

g) Use the electrical power tool, accesso-

ries, inserted tools etc. in accordance

with these instructions and advice, and

the stipulations drawn up for this par-

ticular type of device. In doing this, take

into account the working conditions

and the task in hand. The use of electrical

power tools for purposes other than those in-

tended can lead to dangerous situations.

5. Service

a) Have your device repaired at the ser-

vice centre or by qualified specialist

personnel using original manufacturer

parts only. This will ensure that your device

remains safe to use.

9 GB

General safety advice for electrical power tools

Q

Safety advice for all uses

General safety advice for grinding,

sanding (with sandpaper), wire brushing,

polishing and disc-cutting:

a) This electrical power tool is intended

for use as a grinding, sanding, wire-

brushing, and disc-cutting machine.

Observe all the safety advice, instruc-

tions, information in figures and all

other information you received with

this device. If you do not observe the following

advice it could lead to electric shock, ﬁre and /

or serious injury.

b) Normative statement / advice for this tool is not

applicable.

c) Do not use any accessory not specifi-

cally intended by the manufacturer

for this electrical power tool. Although

an accessory may ﬁt on your electrical power

tool, this does not on its own guarantee that it

can be safely used.

d) The maximum permitted speed of an

attachment must be at least as high as

the maximum speed indicated for the

electrical power tool. An accessory rotating

faster than its permitted speed could disintegrate

or ﬂy oﬀ.

e) The external diameter and the thickness

of the attachment must be compatible

with the dimensions of your electrical

power tool. Attachments that are not dimen-

sionally compatible cannot be adequately

guarded or controlled.

f) Grinding discs, flanges, grinding

wheels or other accessories must fit

exactly on to the spindle of your elec-

trical power tool. Attachments that do not

exactly ﬁt on the spindle turn unevenly, vibrate

severely and could lead to loss of control.

g) Do not use damaged attachments.

Before every use check attachments

such as grinding discs for loose frag-

ments and cracks, grinding wheels for

cracks, deterioration or excessive

wear and wire brushes for loose or

broken wires. If the electrical power

tool or attachment is dropped, inspect

for damage or change the attachment

for an undamaged one. When you

have inspected and inserted the at-

tachment, position yourself and by-

standers away from the plane of the

rotating attachment and run the device

at maximum speed for one minute.

Damaged attachments will usually break apart

during this test.

h) Wear personal protective equipment.

Use a full face visor, safety goggles or

safety glasses, depending on the ap-

plication. Wear a dust mask, hearing

protectors, safety gloves or special

apron capable of stopping particles of

the grinding medium or workpiece, as

appropriate for the task. Eyes must be

protected from the ﬂying debris which can

arise from some operations. Dust or breathing

masks must be capable of ﬁltering out the dust

generated by the application. Prolonged expo-

sure to loud noise can lead to hearing loss.

i) Keep bystanders at a safe distance

from your work area. Anyone entering

the work area must wear personal

protective equipment. Fragments of the

workpiece or of a broken attachment could ﬂy

oﬀ and cause injury beyond the immediate

working area.

j) Hold the device by the insulated han-

dle surfaces when you are undertak-

ing work where there is the danger

of the attachment striking hidden

electricity cables or the device’s mains

lead. Contact with a live wire could cause

metal parts of the device to become live and

lead to electric shock.

k) Keep the mains lead away from rotat-

ing attachments. If you lose control of the

device the mains lead may become severed or

trapped and your hand or arm may be pulled

into the rotating attachment.

l) Never lay the electrical power tool

down until after the attachment has

come to a complete standstill. The rotat-

10 GB

General safety advice for electrical power tools

ing attachment may snag when it comes into

contact with the surface and cause you to lose

control of the device.

m) Do not have the electrical power tool

running while you are carrying it. Your

clothing could become trapped by unintention-

al contact with the rotating attachment and the

tool could be pulled into your body.

n) Clean the ventilation slots on your

electrical power tool regularly. The mo-

tor’s fan draws dust into the housing. A build-up

of metal dust could give rise to an electrical

hazard.

o) Never use the electrical power tool

near inflammable materials. Sparks

could ignite these materials.

p) Do not use attachments that require

the use of coolants. The use of water or

other liquid coolants could result in electric shock.

Q

Safety advice

relating to kickback

Kickback is the sudden reaction to a pinched or

snagged rotating attachment, such as a grinding

disc, grinding pad, wire brush etc. Pinching or

snagging results in the rotating attachment coming

to an abrupt stop. This causes the electrical power

tool (if not controlled) to move in the opposite di-

rection to the direction of rotation of the attachment

at the point of constraint.

If, for example, a grinding disc is pinched or snags

in a workpiece, this can cause the edge of the

grinding disc to penetrate the workpiece, become

trapped there and either free itself or kickback. The

grinding disc moves towards or away from the op-

erator, depending on the direction of movement of

the disc at the point of constraint. The grinding disc

could also break.

Kickback occurs as a result of incorrect use or mis-

use of the electrical power tool. It can be prevented

by taking the appropriate precautions as described

below.

a) Maintain a firm grip on the electrical

power tool and position your body

and arms to allow you to resist kick-

back forces. Always use the auxiliary

handle, if provided, to exercise the

greatest possible control over kick-

back forces or reaction torques as the

device builds up to full speed. By taking

suitable precautions the operator can control

kickback and reaction forces.

b) Do not place your hands near a rotat-

ing attachment. If kickback occurs the at-

tachment could move over your hand.

c) Avoid positioning your body in the

area into which the electrical power

tool would move in the event of a

kickback. A kickback moves the electrical

power tool in the opposite direction to the di-

rection of movement of the grinding disc at the

point of constraint.

d) Work particularly carefully in the

area of corners, sharp edges etc. to

avoid the attachment bouncing or

snagging on the workpiece. Corners,

sharp edges or bouncing have a tendency to

snag the rotating attachment. This causes loss

of control or kickback.

e) Do not use saw-chain woodcarving

discs or toothed discs. Such attachments

create frequent kickback and loss of control of

the electrical power tool.

Q

Special safety advice relating

to grinding and disc-cutting

a) Always use the guard designed for

the type of abrasive consumable you

are using. Always use abrasive con

sum-

ables approved for use with your elec-

trical power tool. Abrasive consumables not

approved for use with your electrical power tool

cannot be adequately guarded and are unsafe.

b) To ensure the highest level of opera-

tional safety, the disc guard cover must

be attached to the electrical power tool

and set in such a way that the smallest

11 GB

General safety advice for electrical power tools

possible area of the abrasive consum-

able is exposed to the operator. The disc

guard cover is there to protect the operator from

pieces breaking oﬀ and accidental contact with

the abrasive consumable.

c) Abrasive consumables must be used

only for their recommended purpos-

es, For example: never grind with the

side face of a cutting disc. Cutting discs

are intended for removing material using the

edge of the disc. Sideways forces on these

abrasive consumables can cause them to break.

d) Always use an undamaged mounting

flange of the correct size and shape

for your selected grinding disc. Suitable

ﬂanges support the grinding disc and reduce the

chance of it breaking. Flanges for cutting discs

are

diﬀerent from the ﬂanges for other abrasive discs.

e) Never use worn down abrasive con-

sumables intended for larger electrical

power tools. Abrasive consumables intended

for larger electrical power tools are not designed

for the faster rotational speeds of these smaller

electrical power tools and could break.

Q

Further special safety

advice for disc-cutting

a) Avoid snagging the cutting disc and

do not use too much contact pressure.

Do not attempt to make excessively

deep cuts. Overloading the cutting disc in-

creases the load and the tendency of the disc

to twist or snag in the cut, making kickback or

disc breakage more likely.

b) Avoid the area in front of or behind

the rotating cutting disc. If the cutting disc

is moving away from you at the point of con-

straint in the workpiece, then, in the event of

a kickback, the electrical power tool and the

rotating disc may be thrown towards you.

c) If the cutting disc jams or you stop

work for a while, switch the device

off and hold it until the disc comes to

a complete stop. Never attempt to

pull the still rotating cutting disc out of

the cut as this could cause kickback.

Determine and rectify the reason for the jamming.

d) Do not switch on the device if the cut-

ting disc is in the workpiece. Allow

the cutting disc to reach full speed be-

fore carefully continuing with the cut.

Otherwise the disc could snag, jump out of the

workpiece or cause a kickback.

e) Support boards or workpieces whilst

cutting to reduce the risk of kickback

caused by a jammed cutting disc. Large

workpieces may bend under their own weight.

The workpiece must be supported to both sides

of the cutting disc and particularly near the

cutting disc and at the workpiece edge.

f) B

e particularly careful when pocket

cutting in existing walls or other areas

where you cannot see what you are cut

-

t

ing into. The cutting disc plunged into the surface

could cut through gas or water pipes, electricity

cables or other objects and cause kickback.

Q

Special safety advice for

abrading using sandpaper

Do not use over-sized sanding sheets.

Follow the manufacturer’s recommen-

dations for sanding sheet size. Sanding

sheets that project beyond the backing pad

could cause injury in addition to jamming,

tearing of the sheet or kickback.

Q

Special safety

advice for polishing

Do not use the polishing bonnet if it

has any loose parts, in particular the

fastening cords. Tuck the fastening cords

away or trim them. Loose fastening cords rotat-

ing with the attachment could catch your ﬁngers

or become trapped in the workpiece.

12 GB

General safety advice for electrical power tools

Q

Special safety advice for

working with wire brushes

a) Bear in mind that wire brushes lose

pieces of wire during normal use. Do

not overload the wires by applying too

much pressure. Flying pieces of wire can very

easily penetrate thin clothing and / or skin.

b) U

se a guard, if recommended, but m

ake

sure that the wire brush does not come

into contact with the guard. The diameters

of disc brushes and cup brushes can increase

due to contact pressure and centripetal forces.

Q

Safety advice for

angle grinders

DANGER OF ELECTRIC SHOCK! Do not

operate the device if the mains lead

or mains plug is damaged.

DANGER OF ELECTRIC SHOCK! Do not

touch the mains lead if it becomes

damaged or cut through while you

are using the device. Pull the plug out of

the mains socket immediately and have the de-

vice repaired by a suitably qualiﬁed person or

at your service centre.

DANGER OF ELECTRIC SHOCK! Do not

operate the device if it is damp and

do not use it in a damp environment.

DANGER OF ELECTRIC SHOCK! If you

use the device outdoors, always con

nect

it through a residual current device

(RCD) with a maximum trip current of

30 mA. If using an extension lead, always use

one that is approved for outdoor use.

Do not suspend or carry the device by

the mains lead. Always work with the

mains lead leading away from the

rear of the device. Otherwise the device

could be damaged.

Grinding discs must be carefully kept

and handled in accordance with the

manufacturer’s instructions. Otherwise

they could be damaged.

Make sure that abrasive consumables

and tools are attached in accordance

with the manufacturer’s instructions

and advice. Otherwise they could become

detached from the device and result in injury

and / or damage to property.

Ensure that any spacers supplied and

required for the use of certain abrasive

consumables and tools are installed.

Do not use separate reducing bushes

or adapters in order to make grinding

discs with a larger bore fit.

When using abrasive consumables

and tools with a threaded insert make

sure that the tread is long enough for

the spindle length. Otherwise the grinding

discs could become detached from the device

and result in injury and / or damage to property.

Do not allow the end of the spindle

to contact the base of the hole in the

abrasive consumable.

Do not work in areas where there may

be concealed electricity cables or gas

or water pipes. Use a suitable detector

or ask your local utility service pro-

viders. Contact with electricity cables can

lead to ﬁre or electric shock. Damaging a gas

pipe can lead to an explosion. Penetration of a

water pipe can lead to property damage or to

electric shock.

NOXIOUS FUMES!

Working with harmful / noxious dusts represents

a risk to the health of the person operating the

device and to anyone near the work area.

When working on metal for longer

periods, connect the tool to a suitable

external extraction system.

Ensure that there is adequate ventila-

tion when working on plastic, paint,

varnish etc.

Do not soak the materials or the sur-

face you are about to work on with

liquids containing solvents.

DANGER OF INJURY! Wear close-fitting

clothing and keep long hair inside a

hairnet or suitable headwear.

13 GB

General safety advice for electrical power tools

For safety reasons this device must

always be used with the auxiliary

handle

4

in place.

The adjustable disc guard cover

5

must

always be in place when working with

roughing, grinding or cutting discs.

Otherwise there could be danger of injury.

Use the vacuum dust extraction facility

if your work generates high amounts

of dust. Use suction devices particular-

ly approved for the purpose.

Use permitted consumables and tools

only. Check that the speed given on the

discs is greater or equal to the rated

speed of the device.

Take note of the direction of rotation

and always hold the device in such a

way that the sparks and grinding de-

bris are thrown away from your body.

Otherwise there could be danger of injury.

Make sure that the dimensions of the

disc are suitable for the device and

that the disc is of a type that fits prop-

erly on to the mounting flange

8

.

Q

Advice on use

Note! Discs must be used only for their recom-

mended purposes, otherwise they could disintegrate,

become damaged or cause accidents.

Roughing (see Fig. G):

Never use cutting discs for

roughing or grinding!

Move the angle grinder using even

pressure to and fro over the workpiece.

Hold the roughing or grinding disc at

a flat angle to the workpiece when

working on a soft material. Use a

slightly steeper angle for harder ma-

terials.

Disc-cutting (see Figs. E, F):

Never use roughing or

grinding discs for cutting!

Only use certified fibre-reinforced cut-

ting or grinding discs approved for use at

circumferential speeds of not less than 80 m / s.

CAUTION! The disc continues to rotate after

the device has been switched oﬀ. Do not at-

tempt to slow it down by pressing on the side

of the disc.

Securely support the workpiece. Use

clamps or a vice to grip the workpiece ﬁrmly.

This is much safer than holding it in your hand.

Switch the device off and allow it to

come to a complete standstill before

you put it down.

Unlock the ON / OFF switch immedi-

ately if a power failure occurs or the

plug is pulled out of the mains socket.

Place the switch in the OFF position.

This prevents the device from being inadvertent-

ly started up again.

Use the device for dry cutting or dry

grinding only.

The auxiliary handle

4

must be in

place

whenever the device is being used.

Do not work on materials containing

asbestos. Asbestos is a known carcinogen.

A tip! Using the device safely.

DANGER! Always guide

the device through the

workpiece against the di-

rection of rotation of the

disc. If you work in the other direction there is

the risk of kickback. The device may be forced

out of the cut.

Always switch on the device before

placing it against the workpiece. After

cutting or grinding, always lift the device from

the workpiece before switching it oﬀ.

When working always hold the device

securely with both hands (see Fig. G).

Always keep proper footing and balance.

14 GB

Use / Use of accessories

General safety advice for electrical power tools / Use

For the best grinding performance move the

device evenly to and fro over the workpiece

maintaining an angle of 15° to 30° (between

grinding disc and workpiece).

When working on inclined surfaces do

not press the device hard down on to

the workpiece. If the speed slows greatly,

use less pressure. This will allow you to work m

ore

eﬀectively and safely. If the device suddenly

stops due to it becoming retarded or trapped,

pull the mains plug from the socket immediately.

Cutting: Advance the device at an

appropriate rate. Do not incline the

cutting disc.

Roughing, grinding and cutting discs

get hot during use – allow them to

cool fully before touching them.

Never use the device for a purpose

for which it was not intended.

Before you insert the mains plug into

the socket, always check that the de-

vice is switched off.

If a dangerous situation arises, pull

the mains plug immediately out of the

mains socket. Ensure that the device and

the mains plug are easily accessible and can

be reached quickly in an emergency.

When taking a break from your

work, before carrying out any tasks

on the device itself and when you are

not using the device, always pull the

mains plug out of the mains socket.

Always keep the device clean, dry and free of

oil or grease.

Remain alert at all times! Always watch

what you are doing and proceed with

caution. Do not use the device if you cannot

concentrate or you are feeling unwell.

Q

Use

Q

Switching on and oﬀ

Check the attached consumable or tool before use.

It must be attached properly, not damaged, damp

or cracked and must rotate freely. Test the operation

of the device for 30 seconds. If a disc is not round

or vibrates, do not use it. Look out for unusual noises

or generation of sparks. Check that all the fastenings

are correctly attached.

Switching on:

Press the safety lock-out

1

.

Press the ON / OFF switch

2

.

Switching off:

Release the ON / OFF switch

2

again.

Q

Setting the speed

Select the desired speed before use to suit your

purpose. Turn the speed preselector wheel

10

to the desired setting. The required rotational

speed depends on the material being worked

and the working conditions and can be deter-

mined by means of a practical test.

The table below shows some recommended

settings (for guidance only and given without

liability) for a number of common applications.

The accessories mentioned may not all be sup-

plied as standard with the product.

Preselected rotation speed:

Material

Application

Tool Setting

Plastic,

varnish

Polishing Lambswool

bonnet

1

Fine ﬁnish

Felt polishing

disc

1

Metal Fine ﬁnish Buﬃng disc 1

Paint

removal

Sanding sheet 2–3

Wood,

metal

Brushing,

derusting

Cup brush,

sanding sheet

3

Metal Grinding /

abrading

Grinding disc 4–6

Metal Roughing /

grinding

Roughing /

grinding disk

6

Metal Cutting Cutting disc 6

15 GB

Use / Use of accessories

General safety advice for electrical power tools / Use

Q

Changing a disc

Always wear protective gloves

when changing cutting or roughing /

grinding discs.

Press the spindle lock button

9

only after the

mounting spindle

7

has reached a standstill,

Fig. A.

Press the spindle lock button

9

to block the

drive.

Release the clamping nut

6

using the spanner

11

, Fig. B.

Place the roughing, grinding or cutting disc on

to the mounting ﬂange

8

with its labelled side

facing towards the device.

Then replace the clamping nut

6

, with its

raised side facing upwards, on to the mounting

spindle

7

.

Press the spindle lock button

9

to block the

drive.

Tighten the clamping nut

6

again with the

spanner

11

.

Note: Replace a new disc immediately if it runs

unevenly or vibrates after being exchanged.

After replacing a disc let the device run under

no load for 30 seconds as a safety check.

Look out for unusual noises or generation of

sparks.

Check that all the fastenings are correctly

attached.

Pay attention to see that the arrow showing the

direction of rotation on the cutting or roughing /

grinding discs (including diamond cutting discs)

corresponds with the direction of rotation of the

device (see arrow on the head of the device).

Q

Use of accessories

Q

Cutting / roughing discs

You can use the following cutting or roughing/

grinding discs with this device:

Dimensions: ø 125 x 22.2 mm

to max. 6 mm thick

(depressed centre)

Speed: min. 12000 rpm

Circumferential speed: 80 m / sec

ø 125 x 22.2 mm

to max. 6 mm thick

(depressed centre)

12000 rpm

80 m / sec

Q

Flap discs for metal

Dimensions: ø 125 mm

Speed: min. 12000 rpm

Q

Other accessories

You can also use abrasive consumables and tools

complying with the following technical speciﬁcation:

Spindle thread: M14

Speed: min. 12000 rpm

Backing plate for grinding discs

Dimensions: ø 115 mm / 125 mm

Grinding discs for wood / masonry attached

with hook and eye ﬁxings

Dimensions: ø 115 mm / 125 mm

16 GB

Maintenance and cleaning / Service / Warranty / Disposal

Use of accessories / Maintenance and cleaning

Note! These may only be used in combination

with a backing plate!

Cup brush, crimped wire

Dimensions: ø 75–100 mm

Speed: min. 12000 rpm

Cup brush, twisted wire

Dimensions: ø 75 mm

Speed: min. 12000 rpm

Cup brush, knotted wire

Dimensions: ø 115 mm

Speed: min. 12000 rpm

Q

Adjusting the disc guard cover

DANGER OF INJURY!

Pull the mains plug out of the mains socket

before you carry out any task on the device.

In order to adjust the safety cover

5

, one does

not need to remove the screws

12

but just loo-

sen them.

12

5

DANGER OF INJURY! Always use the an-

gle grinder with the disc guard cover

5

in

place. The disc guard cover must be securely

attached to the angle grinder. To ensure the

highest level of safety while using the device,

ensure that the smallest possible area of the

grinding or cutting tool is exposed to the oper-

ator at all times (see Fig. C, D). The disc guard

cover

5

is there to protect the operator from

pieces breaking oﬀ and accidental contact

with the grinding or cutting tool. The disc guard

cover has 5 set positions.

Turn the disc guard cover

5

into the desired

position (working position).

The closed side of the disc guard cover

5

must

always be facing the operator.

Q

Using the auxiliary handle

CAUTION! For safety reasons this device must

always be used with the auxiliary handle

4

in

place.

The auxiliary handle

4

can be screwed on to the

left, right or on the top of the head of the device.

Q

Maintenance and cleaning

DANGER OF INJURY!

Pull the mains plug out of the mains socket

before you carry out any task on the device.

Do not use sharp objects for cleaning

the device. Do not allow any liquids

to enter the device. Otherwise the tool may

be damaged.

Have the carbon brushes replaced only at the

service centre or an accredited electrical

equipment repair centre. The device requires

no other maintenance.

17 GB

Maintenance and cleaning / Service / Warranty / Disposal

Use of accessories / Maintenance and cleaning

Clean the device frequently; for best results do

this immediately after you have ﬁnished using it.

Use a dry cloth to clean the housing – under

no circumstances use petrol, solvents or clean-

ing agents that attack plastic.

A vacuum cleaner is required to thoroughly

clean the device.

Ventilation openings must always be kept free.

Remove any adhering dust with a narrow paint

brush.

Q

Service

Have your device repaire

d

at the service centre or by qualified

specialist personnel using original

manufacturer parts only. This will ensure

that your device remains safe to use.

If the plug or lead needs

to be replaced, always have the re-

placement carried out by the manu-

facturer or its service centre. This will

ensure that your device remains safe to use.

Q

Warranty

The warranty for this appliance is for 3 year

s

from the date of purchase. The appliance

has been manufactured with care and me-

ticulously examined before delivery. Please

retain your receipt as proof of purchase. In

the event of a warranty claim, please make

contact by telephone with our Service

Department. Only in this way can a post-

free despatch for your goods be assured.

The warranty covers only claims for material and

maufacturing defects, but not for transport damage,

for wearing parts or for damage to fragile components,

e.g. buttons or batteries. This product is for private use

only and is not intended for commercial use.

The warranty is void in the case of abusive and

improper handling, use of force and internal tam-

pering not carried out by our authorized service

branch. Your statutory rights are not restricted in

any way by this warranty.

The warranty period will not be extended by repairs

made unter warranty. This applies also to replaced

and repaired parts. Any damage and defects extant

on purchase must be reported immediately after

unpacking the appliance, at the latest, two days after

the purchase date. Repairs made after the expiration

of the warranty period are subject to payment.

GB

Service Great Britain

Tel.: 0871 5000 720

(0,10 GBP/Min.)

e-mail: kom[email protected]

IAN 90983

Q

Disposal

The packaging is wholly composed of

environmentally-friendly materials that can

be disposed of at a local recycling centre.

Do not dispose of electric tools

in the household waste!

In accordance with European Directive 2002 / 96 / EC

(covering waste electrical and electronic equipment)

and its transposition into national legislation, worn out

electrical power tools must be collected separately

and taken for environmentally compatible recycling.

Contact your local refuse disposal authority for more

details of how to dispose of your worn out electrical

devices.

18 GB

Spis zawartości

Declaration of Conformity / Manufacturer

Q

Declaration of Conformity /

Manufacturer

We, KOMPERNASS HANDELS GMBH, the person

responsible for documents: Mr Semi Uguzlu, BURG-

STRASSE 21, 44867 BOCHUM, GERMANY, hereby

declare that this product complies with the following

standards, normative documents and EU directives:

Machinery Directive

(2006 / 42 / EC)

EU Low Voltage Directive

(2006 / 95 / EC)

Electromagnetic Compatibility

(2004 / 108 / EC)

RoHS Directive

(2011 / 65 / EU)

Applicable harmonized standards

EN 60745-1/A11:2010

EN 60745-2-3:2011

EN 55014-1/A1:2009

EN 55014-2/A2:2008

EN 61000-3-2/A2:2009

EN 61000-3-3:2008

Type / Device description:

Angle grinder PWS 125 A1

Date of manufacture (DOM): 06–2013

Serial number: IAN 90983

Bochum, 30.06.2013

Semi Uguzlu

- Quality Manager -

We reserve the right to make technical modiﬁcations

in the course of further development.

19 PL

Spis zawartości

Wstęp

Zastosowanie zgodne z przeznaczeniem .....................................................................................Strona 20

Wyposażenie ...................................................................................................................................Strona 20

Zakres dostawy ................................................................................................................................Strona 20

Dane techniczne ..............................................................................................................................Strona 20

Ogólne wskazówki bezpieczeństwa dla elektronarzędzi

1. Bezpieczeństwo miejsca pracy ..................................................................................................Strona 21

2. Bezpieczeństwo elektryczne .......................................................................................................Strona 21

3. Bezpieczeństwo osób .................................................................................................................Strona 22

4. Staranne obchodzenie się i użytkowanie narzędzi elektrycznych ..........................................Strona 22

5. Serwis ...........................................................................................................................................Strona 23

Wskazówki bezpieczeństwa dla wszystkich zastosowań ............................................................Strona 23

Odrzut i odpowiednie wskazówki bezpieczeństwa......................................................................Strona 24

Szczególne wskazówki odnośnie szlifowania i cięcia ..................................................................Strona 25

Dalsze szczególne wskazówki bezpieczeństwa dotyczące tarcz tnących ................................. Strona 25

Szczególne wskazówki bezpieczeństwa dotyczące szlifowania papierem ściernym ................Strona 26

Szczególne wskazówki bezpieczeństwa dotyczące polerowania .............................................. Strona 26

Szczególne wskazówki bezpieczeństwa dotyczące pracy przy użyciu szczotek drucianych ......Strona 26

Wskazówki bezpieczeństwa dla szlifierki kątowej .......................................................................Strona 26

Wskazówki dotyczące pracy..........................................................................................................Strona 28

Obsługa

Włączanie i wyłączanie ..................................................................................................................Strona 29

Ustawianie prędkości obrotowej ....................................................................................................Strona 29

Wymiana narzędzi roboczych .......................................................................................................Strona 30

Stosowanie wyposażenia

Tarcze tnące / do szlifowania zgrubnego ......................................................................................Strona 30

Ściernice wachlarzowe do metalu ..................................................................................................Strona 30

Pozostałe wyposażenie ...................................................................................................................Strona 30

Przestawienie osłony........................................................................................................................Strona 31

Stosowanie uchwytów dodatkowych ............................................................................................. Strona 32

Konserwacja i czyszczenie............................................................................................Strona 32

Serwis .............................................................................................................................................Strona 32

Gwarancja ..................................................................................................................................Strona 32

Utylizacja .....................................................................................................................................Strona 33

Deklaracja zgodności / Producent ..........................................................................Strona 33

Declaration of Conformity / Manufacturer

20 PL

Wstęp / Ogólne wskazówki bezpieczeństwa dla elektronarzędzi

Wstęp

Szliﬁerka kątowa PWS 125 A1

Szlifowanie, obróbka zgrubna, cięcie

Q

Wstęp

Gratulujemy zakupu nowego urządzenia. Tym sa-

mym zdecydowali się Państwo na zakup produktu

wysokiej jakości. Instrukcja obsługi jest częścią tego

produktu. Zawiera ona ważne wskazówki dotyczące

bezpieczeństwa, użytkowania iutylizacji. Przed

pierwszym użyciem produktu należy zapoznać się

ze wszystkimi wskazówkami dotyczącymi obsługi

ibezpieczeństwa. Używać produktu wyłącznie

zgodnie zjego poniżej opisanym przeznaczeniem.

Wprzypadku przekazania produktu innej osobie

należy dołączyć do niego całą jego dokumentację.

Q

Zastosowanie zgodne

z przeznaczeniem

Urządzenie jest przeznaczone do oddzielania, tarcia

i szczotkowania tworzyw metalowych bez zastoso-

wania wody. Każde użycie lub zmiana urządzenia

uważane są jako niezgodne z przeznaczeniem

niesie ze sobą znaczne zagrożenia wypadkowe.

Producent nie ponosi żadnej odpowiedzialności za

szkody wynikające z użycia niezgodnego z prze-

znaczeniem. Urządzenie nie jest przeznaczone do

użytku zawodowego.

Wskazówka: Szczeliny w ścianach nośnych

podlegają normie DIN 1053 Część 1 lub postano-

wieniom specyﬁcznym dla danego kraju.

Przed rozpoczęciem pracy należy skonsultować

zagadnienie z odpowiedzialnym statykiem, archi-

tektem lub kompetentnym kierownikiem budowy.

Q

Wyposażenie

1

Blokada włączenia

2

WŁĄCZNIK / WYŁĄCZNIK

3

Pokrywka szczotek węglowych

4

Uchwyt dodatkowy

5

Osłona przestawna

6

Nakrętka mocująca

7

Wrzeciono mocujące

8

Kołnierz mocujący

9

Przycisk blokady wrzeciona

10

Kółko nastawcze ustawienie prędkości obrotowej

11

Klucz do mocowania (Rys. B)

Q

Zakres dostawy

1 Szliﬁerka kątowa PWS 125 A1

1 Tarcza tnąca do metalu

1 Uchwyt dodatkowy

1 Osłona

1 Klucz mocujący

1 Instrukcja obsługi

Q

Dane techniczne

Obciążenie znamionowe: 1200 W

Napięcie nominalne: 230–240 V∼, 50 Hz

Znamionowa liczba

obrotów: n 12000 min

-1

Bezstopniowo

regulowane obroty: 3000 do 12000 min

-1

Gwint wrzeciona: M14

Klasa ochrony: II /

Informacje dotyczące hałasu i wibracji:

Wartość pomiarowa hałasu wyznaczona zgodnie

z EN 60745. Poziom hałasu elektronarzędzia wg

oceny A wynosi typowo:

Poziom ciśnienia hałasu: 91 dB(A)

Pozom mocy hałasu: 102 dB(A)

Niepewność pomiaru K: 3 dB

Zakładać ochronniki słuchu!

Wartości całkowite drgań wyznaczone

zgodnie z EN 60745:

Szlifowanie powierzchni (zgrubne):

Wartość emisji drgań a

h, AG

= 13,431 m / sek

2

,

Niepewność K = 1,5 m / sek

2

.

Podany w niniejszych in-

strukcjach poziom drgań wyznaczony został za

pomocą metody pomiarowej określonej w normie

EN 60745 i może zostać użyty do porównania

Stránka sa načítava...

Parkside PWS 125 A1 ANGLE GRINDER Operation and Safety Notes

Parkside PWS 125 A1 ANGLE GRINDER Operation and Safety Notes

v iných jazykoch

Súvisiace články

Ostatné dokumenty