Parkside PISG 120 B3 Používateľská príručka

IAN 337360_2007

INVERTER WELDER

INVERTERSKI VARILNI APARAT

INVERTERES

HEGESZTŐKÉSZÜLÉK

INVERTNÍ SVÁŘEČKA

INVERTNÁ ZVÁRAČKA INVERTER-SCHWEIßGERÄT

Operation and Safety Notes

Translation of the original instructions

Navodila za upravljanje in varnostna opozorila

Prevod originalnega navodila za uporabo

Kezelési és biztonsági hivatkozások

Az eredeti használati utasítás fordítása

Návod k obsluze a bezpečnostní pokyny

Originální návod k obsluze

Návod na obsluhu a bezpečnostné upozornenia

Originálny návod na obsluhu Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung

GB

SI

HU

CZ

SK DE AT CH

INVERTER WELDER PISG 120 B3

SK

SI

CZ

HU

GB

Before reading, unfold the page containing the illustrations and familiarise yourself with all

functions of the device.

HU

Olvasás előtt hajtsa ki az ábrát tartalmazó oldalt, és ezután ismerje meg a készülék

mindegyik funkcióját.

SI

Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.

CZ

Než začnete číst tento návod k obsluze, rozložte stránku s obrázky a seznamte se se všemi

funkcemi zařízení.

SK

Prv než začnete čítať tento návod, rozložte si stranu s obrázkami a potom sa oboznámte so

všetkými funkciami zariadenia.

DE AT CH

Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich

anschließend mit allen Funktionen des Gerätes vertraut.

GB Operation and Safety Notes Page 5

HU Kezelési és biztonsági hivatkozások Oldal 23

SI Navodila za upravljanje in varnostna opozorila Stran 43

CZ Návod k obsluze a bezpečnostní pokyny Strana 61

SK Návod na obsluhu a bezpečnostné upozornenia Strana 79

DE / AT / CH Montage-, Bedienungs- und Sicherheitshinweise Seite 97

A

C1

C3

C2

C4

B

–

(minus)

+

(plus)

1

4

10

9

5

8 7

7

11

1 2

2

3

6

11

8

7 12

5GB

Table of contents

List of pictograms used .........................................................................Page 6

Introduction ..............................................................................................Page 7

Intended use ................................................................................................ Page 7

Package contents .........................................................................................Page 7

Parts description ..........................................................................................Page 7

Technical speciﬁcations .................................................................................Page 7

Safety instructions ..................................................................................Page 8

Potential hazards during electric arc welding ................................................... Page 10

Welding mask-speciﬁc safety instructions .........................................................Page 12

Environment with increased electrical hazard...................................................Page 13

Welding in tight spaces ................................................................................Page 14

Total of open circuit voltages .........................................................................Page 14

Using shoulder straps ...................................................................................Page 14

Protective clothing ........................................................................................Page 15

EMC Device Classiﬁcation ............................................................................Page 15

Before use .................................................................................................Page 16

Fit welding mask ....................................................................................Page 16

Using the device ...................................................................................... Page 17

Welding .....................................................................................................Page 18

Maintenance and cleaning ................................................................... Page 19

Information about recycling and disposal ....................................... Page 19

EU Declaration of Conformity ..............................................................Page 19

Warranty conditions ..................................................................................... Page 20

Warranty period and statutory claims for defects .............................................Page 20

Extent of warranty ........................................................................................Page 20

Processing of warranty claims ........................................................................Page 21

Service .......................................................................................................Page 21

6GB

List of pictograms used

Caution! Read the operating

instructions! Risk of serious injury

or death.

50/60Hz

Power input;

Number of phases and

Alternating current symbol and

rated value of the frequency.

Caution!

Risk of electric shock!

Important note!

Do not dispose of electrical

devices in household waste!

Dispose of the device and

packaging in an environmen-

tally friendly manner.

Never use the device in the

open or when it’s raining! Manual arc welding with

encased rod electrodes.

Electric shock from the

welding electrode can be

fatal! IP21S Protection class.

Inhalation of welding fumes

can endanger your health. Suitable for welding under

increased electrical hazard.

Welding sparks can cause

an explosion or ﬁre.

Single-phase static frequency

converter-transformer-

commutator.

Arc beams can damage your

eyes and injure your skin. HInsulation class.

MV

Electromagnetic ﬁelds can

disrupt the function of cardiac

pacemakers. Direct current.

Warning: Potential hazards! Made from recycling

material.

X % Duty cycle. U0

Rated value of the open

circuit voltage

I1 max

Greatest rated value of the

mains current U1

Rated value of the mains

voltage

I2 max

Greatest rated value of the

welding current U2

Standardised operating

voltage

I1 eff

Effective value of the greatest

mains current

7GB

INVERTER WELDER

PISG 120 B3

zIntroduction

Congratulations!

You have purchased one

of our high-quality

products. Please familiarise yourself with

the product before using it for the ﬁrst

time. Please also read the safety instruc-

tions carefully. This product must be set

up or used only by people who have

been trained to do so.

KEEP OUT OF THE REACH OF

CHILDREN!

zIntended use

This welding device is ideal for welding

metals such as carbon steel, steel alloy,

other stainless steel, copper, aluminium,

titanium, etc. The product has a control

lamp, a heat protection display and a

cooling fan. In addition, it is ﬁtted with

a carrying strap so that the product

can be lifted and moved safely. If it is

not handled properly the product can

be dangerous for individuals, animals

and property. Use the product only

as described and only for the speciﬁc

applications as stated. Keep these

instructions in a safe place. Ensure you

hand over all documentation when

passing the product on to anyone else.

Any use that differs to the intended

use as stated above is prohibited and

potentially dangerous. Damage or

injury caused by misuse or disregarding

the above warning is not covered by the

warranty or any liability on the part of

the manufacturer. The device is intended

for professional use. Commercial use

will void the guarantee.

zPackage contents

1 Inverter welder

1 Welding mask

2 Welding cables

1 Combi wire brush with slag

hammer

1 Carrying strap

5 Welding electrodes (2 x 1.6 mm;

2 x 2.0 mm; 1 x 2.5 mm)

1 Operating instructions

zParts description

1

Carrying strap

2

Rotary knob

3

Control lamp for overheating

4

Ground terminal

5

Electrode holder

6

Combi wire brush with slag hammer

7

Welding mask

8

Handle

9

ON/OFF switch

10

Power cable 4 m

11

Protective glass

12

Welding electrodes

zTechnical speciﬁcations

Mains connection: 230 V

50/60 Hz

Nominal power input: 3.6 kW

Max. welding current

and the appropriate

standardised operating

voltage:

10A/20.4V –

120A/24.8V

Rated value of the mains

voltage: U1:230V

Greatest rated value of

the mains current: I1max: 22 A

Introduction

8GB

Maximum effective input

current: I1eff: 11 A

Rated value of the open

circuit voltage: U0: 80 V

Protection class: IP21S

Weight: approx. 3 kg

Duty cycle X: 30% at 40°C

and 120 A

Falling characteristic

Material thicknesses

which can be welded: 1.5 mm –

3.0mm

Safety instructions

Please read the operating instruc-

tions with care and observe the

notes described. Familiarise your-

self with the device, its proper

use and the safety instructions

based on these operating instruc-

tions. The rating plate contains

all technical data of this welding

device; please learn about the

technical features of this device.

Keep the

packaging material away from

small children. There is a risk

of suffocation!

This device may be used by

children aged 16 years and

older, and by persons with

reduced physical, sensory or

mental capacities, or a lack of

experience and knowledge,

if they are supervised or have

been instructed in how to use

the device safely and under-

stand the dangers that may

arise when using it. Do not

allow children to play with the

device. Cleaning and day-to-

day maintenance must not be

performed by children without

supervision.

Repairs or/and maintenance

work must only be carried out

by qualiﬁed electricians.

Only use the weld cable

provided in the scope of

delivery.

During operation, the device

should not be positioned

directly on the wall, covered or

jammed between other devices

so that sufﬁcient air can be

absorbed through the ventila-

tion slats. Make sure that the

device is correctly connected

to the supply voltage. Avoid

any form of tensile stress of

the power cable. Disconnect

the plug from the socket prior

to setting up the device in

another location.

If the device is not in opera-

tion, always switch it off by

pressing the ON/OFF switch.

Place the electrode holder on

an insulated surface and only

remove it from the holder after

allowing it to cool down for

15 minutes.

Introduction / Safety instructions

9GB

Pay attention to the condition

of the welding cable, electrode

holder and the earth terminal.

Wear and tear of the insulation

and the live parts can lead to

hazards and reduce the quality

of the welding work.

Arc welding creates sparks,

molten metal parts and smoke.

Therefore ensure that: All

ﬂammable substances and/or

materials are removed from the

work station and its immediate

surrounding.

Ensure the work station is

ventilated.

Do not weld on containers,

vessels or tubes that contain or

contained ﬂammable liquids or

gases.

Avoid any

form of direct contact with the

welding current circuit. The

open circuit voltage between

the electrode holder and earth

terminal can be dangerous,

there is a risk of electric shock.

Do not store or use the device

in a damp or wet environment

or in the rain. Protection rating

IP21S is applicable in this

case.

Protect your eyes using the

appropriate protective glasses

(DIN level 9-10), which are fas-

tened to the supplied welding

mask. Wear gloves and dry

protective clothing that are free

of oil and grease to protect the

skin from exposure to ultravio-

let radiation of the arc.

Do not use

the welding power source to

defrost pipes.

Please note:

The light radiation emitted by

the electric arc can damage

eyes and cause burns to the

skin.

Arc welding creates sparks

and drops of melted metal.

The welded workpiece starts to

glow and remains hot for a rel-

atively long period. Therefore,

do not touch the workpiece

with bare hands.

Arc welding can cause

vapours to be release that

may be hazardous to health.

Be careful not to inhale these

vapours.

Protect yourself from the

harmful effects of the electric

arc and keep people that are

not involved in the work away

from the arc maintaining a

distance of at least 2 m.

ATTENTION!

During the operation of

the welding device, other

Safety instructions

10 GB

consumers may experience

problems with the voltage sup-

ply depending on the network

conditions at the connection

point. In case of doubt, please

contact your energy supply

company.

During the operation of the

welding device, other devices

may malfunction, e.g. hearing

aids, cardiac pacemakers, etc.

z Potential hazards

during electric arc

welding

There are a series of potential

hazards that can occur during

electric arc welding. It is therefore

particularly important for the

welder to observe the following

rules to avoid endangering him/

herself and others and to prevent

damage to people and the

device.

Work on the voltage side, e.g.

on cables, plugs, sockets etc.,

may only be carried out by

qualiﬁed electricians accord-

ing to national and local

regulations.

In the event of accidents,

disconnect the welding

device from the mains voltage

immediately.

If electrical contact voltages

occur, switch off the device

immediately and have it

checked by a qualiﬁed

electrician.

Always ensure good electrical

contacts on the welding current

side.

Always wear insulating gloves

on both hands during welding

work. These provide protection

from electrical shocks (no-load

voltage of the welding current

circuit), harmful radiations

(heat and UV radiation)

and incandescent metal and

splashes of slag.

Wear sturdy, insulating shoes.

The shoes should also insulate

when exposed to moisture.

Loafers are not suitable as

falling incandescent metal

droplets can cause burns.

Wear suitable protective cloth-

ing, no synthetic garments.

Do not look into the electric

arc without eye protection;

only use a welding mask with

the prescribed protective glass

as per DIN. In addition to light

and heat radiation, which

can dazzle or cause burns,

the electric arc also emits UV

radiation. Without suitable

protection the invisible ultravi-

olet radiation can cause very

Safety instructions

11GB

painful conjunctivitis which

is not apparent until several

hours later. Furthermore, UV

radiation can cause burns with

sunburn-like effects on unpro-

tected parts of the body.

Any persons in the vicinity

of the electric arc or helpers

must also be informed of the

dangers and be equipped

with the necessary protective

equipment. If necessary, set up

protective walls.

Ensure an adequate supply

of fresh air whilst welding,

particularly in small spaces,

as it produces smoke and

harmful gases.

No welding work may be

carried out on containers that

have been used for storing

gases, fuels, mineral oils or

similar – even if they have

been empty for a long time –

as possible residues may

present a risk of explosion.

Special regulations apply in

rooms where there is a risk

of ﬁre or explosion.

Welded joints that are subject

to heavy stress loads and are

required to comply with certain

safety requirements may only

be carried out by specially

trained and certiﬁed welders.

Examples of this are pressure

vessels, running rails, tow

bars, etc.

ATTENTION! Always connect

the earth terminal as close as

possible to the point of weld to

provide the shortest possible path

for the welding current from the

electrode to the earth terminal.

Never connect the earth terminal

to the housing of the welding

device! Never connect the earth

terminal to earthed parts far away

from the workpiece, e.g. a water

pipe in another corner of the

room. This could otherwise dam-

age the protective bonding system

of the room you are welding.

Do not use the welding device

in the rain.

Do not use the welding device

in a moist environment.

Only place the welding device

on a level surface.

The output is rated at an ambi-

ent temperature of 20°C. The

welding time can be reduced

at higher temperatures.

Risk of electric shock:

Electric shock from the

welding electrode can be

fatal. Do not weld in rain or

snow. Wear dry insulating gloves.

Do not touch the electrodes with

Safety instructions

12 GB

bare hands. Do not wear wet or

damaged gloves. Protect yourself

from electric shock with insulation

against the workpiece. Do not

open the device housing.

Danger from welding

fumes:

Inhalation of welding fumes

can endanger health.

Do not keep your head in the

fumes. Use the equipment in

open areas. Use extractors

to remove the fumes.

Danger from welding

sparks:

Welding sparks can cause

an explosion or ﬁre. Keep

ﬂammable substances away

from the welding location.

Do not weld next to ﬂammable

substances. Welding sparks

can cause ﬁres. Keep a ﬁre

extinguisher close by and an

observer should be present to

be able to use it immediately.

Do not weld on drums or any

other closed containers.

Danger from arc beams:

Arc beams can damage your

eyes and injure your skin.

Wear a hat and safety goggles.

Wear hearing protection and

high, closed shirt collars.

Wear welding safety helmets

and make sure you use the

appropriate ﬁlter settings. Wear

complete body protection.

Danger from

electromagnetic ﬁelds:

Welding current generates elec-

tromagnetic ﬁelds. Do not use

if you have a medical implant.

Never wrap the welding cable

around your body. Guide

welding cables together.

z Welding mask-speciﬁc

safety instructions

With the help of a bright light

source (e.g. lighter) examine

the proper functioning of the

welding mask prior to starting

with any welding work.

Weld spatters can damage the

protective screen. Immediately

replace damaged or scratched

protective screens.

Immediately replace damaged

or highly contaminated or

splattered components.

The device must only be

operated by people over the

age of 16.

Safety instructions

13GB

Please familiarise yourself with

the welding safety instructions.

Also refer to the safety instruc-

tions of your welding device.

Always wear a welding mask

while welding. If it is not

used, you could sustain severe

lesions to the retina.

Always wear protective cloth-

ing during welding operations.

Never use the welding mask

without the protective screen.

Regularly replace the protec-

tive screen to ensure good

visibility and fatigue-proof

work.

z Environment with

increased electrical

hazard

When welding in environments

with increased electrical hazard,

the following safety instructions

must be observed. Environments

with increased electrical hazard

may be encountered, for example:

In workplaces where the space

for movement is restricted,

such that the welder is working

in a forced posture (e.g.:

kneeling, sitting, lying) and is

touching electrically conductive

parts;

In workplaces which are

restricted completely or in

part in terms of electrical

conductivity and where there is

a high risk through avoidable

or accidental touching by the

welder;

In wet, humid or hot work-

places where the air humidity

or weld signiﬁcantly reduces

the resistance of human skin

and the insulating properties

or effect of protective equip-

ment.

Even a metal conductor or

scaffolding can create an

environment with increased

electrical hazard.

In this type of environment,

insulated mats and pads must

be used. Furthermore gauntlet

gloves and head protection made

of leather or other insulating

materials must be worn to insu-

late the body against Earth. The

welding power source must be

located outside the working area

or electrically conductive surfaces

and out of the welder’s reach.

Additional protection against a

shock from the mains power in

the event a fault can be provided

by using a fault-circuit interrupter,

Safety instructions

14 GB

which is operated with a leakage

current of no more than 30 mA

and covers all mains-powered

devices in close proximity. The

fault-circuit interrupter must be

suitable for all types of current.

There must be means of rapid

electrical isolation of the welding

power source or the welding cir-

cuit (e.g. emergency stop device)

which are easily accessible.

When using welding devices

under electrically dangerous

conditions, the output voltage

of the welding device must be

greater than 113 volt when idling

(peak value). Based on the output

voltage this welding device may

be used in these conditions.

z Welding in tight spaces

When welding in tight spaces this

may pose a hazard through toxic

gases (risk of suffocation).

In tight spaces you may only

weld if there are trained individu-

als in the immediate vicinity who

can intervene if necessary. In this

case, before starting the welding

procedure, an expert must carry

out an assessment in order to

determine what steps are neces-

sary, in order to guarantee safety

at work and which precautionary

measures should be taken during

the actual welding procedure.

z Total of open circuit

voltages

When more than one welding

power source is operated at the

same time, their open circuit

voltages may add up and lead to

an increased electrical hazard.

Welding power sources must be

connected in such a way that the

danger is minimised. The indi-

vidual welding power sources,

with their individual control units

and connections, must be clearly

marked, in order to be able to

identify which device belongs to

which welding power circuit.

z Using shoulder straps

Welding must not take place if the

welding power source is being

carried e.g. with a shoulder strap.

This is intended to prevent:

The risk of losing your balance

if the lines or hoses which are

connected are pulled

The increased risk of an

electric shock as the welder

Safety instructions

15GB

comes into contact with the

earth if he/she is using a Class

I welding power source, the

housing of which is earthed

through its conductor.

z Protective clothing

At work, the welder must

protect his/her whole body by

using appropriate clothing and

face protection against radia-

tions and burns. The following

steps must be observed:

Wear protective clothing

prior to welding work

Wear gloves.

Open windows or use fans

to guarantee air supply.

Wear safety goggles and

face mask.

Gauntlet gloves made of a

suitable material (leather) must

be worn on both hands. They

must be in perfect condition.

A suitable apron must be

worn to protect clothing from

ﬂying sparks and burns.

When speciﬁc work, e.g.

overhead welding, is required,

a protective suit must be worn

and, if necessary, even head

protection.

Protection against rays

andburns

Warn of the danger to the

eyes by hanging up a sign

saying “Caution! Do not look

into ﬂames!”. The workplaces

must be shielded so that the

persons in the vicinity are

protected. Unauthorised

persons must be kept away

from welding work.

The walls in the immediate

vicinity of ﬁxed workplaces

should neither be bright

coloured or shiny. Windows

up to head height must be

protected to prevent rays

from penetrating or reﬂecting

through them, e.g. by using

suitable paint.

z EMC Device

Classiﬁcation

According to the standard

IEC 60974-10, this is a weld-

ing device in electromagnetic

compatibility Class A. Class A

devices are devices that are

suitable for use in all other areas

except living areas and areas

that are directly connected to

a low-voltage supply mains

that (also) supplies residential

buildings. Class A devices

Safety instructions

16 GB

mustadhere to the Class A limit

values.

WARNING NOTICE: Class A

devices are intended for use in

an industrial environment. Due to

the power-related as well as the

radiated interference variables,

difﬁculties might arise in ensuring

electromagnetic compatibility in

other environments.

Even if the device complies

with the emission limit values in

accordance with the standard,

such devices can still cause

electromagnetic interference in

sensitive systems and devices.

The user is responsible for faults

caused by the arc while working,

and the user must take suitable

protective measures. In doing so,

the operator must consider the

following:

– network, control, signal and

telecommunication lines

– computers and other micropro-

cessor-controlled devices

– TVs, radios and other playback

devices

– electronic and electrical safety

equipment

– people with cardiac pacemak-

ers or hearing aids

– measurement and calibration

devices

– interference immunity of other

equipment nearby

– the time of day at which the

work is being done. The follow-

ing is recommended to reduce

possible interference radiation:

– equip the mains connection

with a mains ﬁlter

– service the device regularly and

keep it in good condition

– welding cables should be

completely uncoiled and run as

close to parallel with the ﬂoor

as possible

– if possible, devices and systems

at risk from interference radi-

ation should be removed from

the work area or shielded.

The product is intended solely for

professional use.

zBefore use

Take the device and accessories out

of the packaging and check them for

damage (e.g. transport damage).

Fix the carrying strap

1

onto the

device (see Fig. C1 – C4).

zFit welding mask

Fit the handle

8

onto the welding

mask

7

, as shown in Fig. A.

Fit the protective glass

11

on to the

welding mask

7

, as shown in Fig. A.

The protective glass

11

must be

pushed in from the top.

Safety instructions / Before use / Fit welding mask

17GB

Note: If you are not able to push the

protective glass

11

in fully, gently press

on the outside of the protective glass

11

.

zUsing the device

Note: The welding device is designed

for welding with electrodes.

Use the electrode holder clamps with-

out protruding bracket screws, which

meet the current safety standards.

Make sure that the ON/OFF switch

9

is set to position “O” (“OFF”)

or that the power cable

10

is not

plugged into the socket.

Connect the welding cable accord-

ing to its polarity and in accordance

with the speciﬁcations of the elec-

trode manufacturer.

To do this, connect the connector of

the earth terminal

4

(black) with the

relevant output on the inverter welder

(black, marked with “-”).

Connect the connector of the elec-

trode holder

5

(red) with the

relevant output on the inverter welder

(red, marked with “+”).

Put on appropriate protective

clothing in accordance with the

speciﬁcations and prepare your

workspace.

Connect the earth terminal

4

to the

workpiece.

Clamp the electrode into the elec-

trode holder

5

.

Switch the device on by setting the

ON/OFF switch to the

9

“I” (“ON”)

position.

Adjust the welding current using the

rotary knob

2

depending on the

electrode being used.

Note: See the following table for

information on the welding current to

be used, depending on the electrode

diameter.

Ø Electrode Welding current

1.6 mm 40 – 55 A

2.0 mm 55 – 65 A

2.5 mm 65 – 80 A

3.2 mm 80 – 120 A

Attention: Do not bring the earth

terminal

4

and the electrode holder

5

/

electrodes into direct contact with one

another.

Attention: When welding with

electrodes (MMA – manual metal arc

welding – electrode welding), the

electrodeholder

5

and the earth

terminal

4

must be connected in

accordance with the speciﬁcations of

the electrodes to plus (+) or minus (-).

Hold the welding mask

7

in front of

the face and start the welding

procedure.

To stop the procedure, set the ON/

OFF switch

9

to “O” (“OFF”)

position.

ATTENTION!

When the thermal sensor is triggered,

the yellow control lamp

3

lights up. In

this case, it will not be possible to

continue welding. The device will

remain in operation so that the fan can

cool the device. As soon as the device

is ready for operation again, the yellow

control lamp

3

will switch off automati-

cally. The welding function can now be

used again.

ATTENTION!

Make sure that you do not rub the

electrodes. Doing this can damage the

workpiece and make it more difﬁcult to

ignite the arc. After the arc is ignited,

maintain the correct gap from the

workpiece. The distance should be

appropriate to the diameter of the

Fit welding mask / Using the device

18 GB

electrode used. When welding maintain

this gap as accurately and consistently

as possibly. The angle between the

electrode and the direction of operation

should be between 20° and 30°.

ATTENTION!

The welding clamp and welding elec-

trodes must be placed on the insulated

bracket after welding. Wait until the

electrode is cooled before removing the

welding slag. To weld an intermittent

weld seam again you must ﬁrst remove

the welding slag at the welding posi-

tion.

ATTENTION!

A voltage which is 10% below the rated

input voltage of the welding device can

have the following consequences:

The power to the device will reduce.

The arc stops or becomes unstable.

ATTENTION!

The arc radiation can lead to inﬂam-

mation of the eyes and skin burns.

Casting and welding slag can cause

eye injuries and burns.

Wear tinted safety goggles or a

protective mask.

The safety mask must meet the

EN175 safety standards.

It is essential that you only use the

welding cable which is included with

the delivery (10mm2).

zWelding

Choose between push and drag welding. The following section shows the impact of

the direction of movement on the properties of the weld seam:

Push welding Drag welding

Burn smaller larger

Weld seam width larger smaller

Weld bead ﬂatter higher

Weld seam fault larger smaller

Note: You decide for yourself which

type of welding is most suitable, once

you have welded a sample piece.

Note: Once it has worn down com-

pletely, the electrode must be replaced.

Using the device / Welding

19GB

zMaintenance and

cleaning

Note: The welding device must be

regularly serviced and overhauled for

proper function and for compliance with

the safety requirements. Improper and

wrong operation may cause failures and

damage to the device.

Before performing cleaning work on

the welding tool, disconnect the

power cable

10

from the power

outlet to ensure the tool is safely

isolated from the power supply.

Clean the exterior of the welding

device and its accessories regularly.

Use compressed air, cotton waste or

a brush to remove dirt and dust.

Note: The following kinds of mainte-

nance work must be performed only by

suitably-qualiﬁed personnel.

The current regulator, earthing

device, internal cables, the coupling

device of the welding torch and

adjusting screws must be serviced

regularly. Re-tighten loose screws

and replace rusty screws (replace-

ment M4 x 10 screws are available

in any commercial hardware store).

Check the insulation resistance levels

of the welding device regularly.

To do this use an appropriate

measuring device.

In case of a defect or a necessary

replacement of equipment parts,

please contact the appropriate

qualiﬁed personnel.

zInformation about

recycling and disposal

Don’t throw away –

recycle

Please return this device, accesso-

ries and packaging to your local

recycling depot.

According to European Directive

2012/19/EU, used electrical devices

must be collected separately for envi-

ronmentally compatible recycling or

recovery. Please return this device to an

approved waste management company

or use your municipal waste collection

service. Please ensure you comply with

local regulations. If you have any ques-

tions, please contact your local authority

or waste management company.

zEU Declaration of

Conformity

We,

C.M.C. GmbH

Responsible for documentation:

Dr Christian Weyler

Katharina-Loth-Str. 15

66386 St. Ingbert

Germany

hereby take sole responsibility for

declaring that the product

Inverter welder

Art. no.: 2338

Year of manufacture: 2021/18

IAN: 337360_2007

Model: PISG 120 B3

meets the basic safety requirements as

speciﬁed in the European Directives

EC low-voltage directive:

2014 / 35 / EU

EC Guideline on Electromagnetic

Compatibility:

2014 / 30 / EU

RoHS directive:

2011 / 65 / EU+2015/863/EU

Maintenance and cleaning / Information about recycling ... / EU Declaration ...

20 GB

EU Declaration of Conformity / Warranty and service information

and the amendments to these Directives.

The object of the declaration described

above meets the requirements of

Directive 2011/65/EU of the European

Parliament and of the Council of 8June

2011 on the restriction of the use of

certain hazardous substances in

electrical and electronic equipment.

This conformity assessment is based on

the following harmonised standards:

EN 60974-1:2018/A1:2019

EN 60974-10:2014/A1:2015

St. Ingbert, 22/10/2020

pp Dr Christian Weyler

– Quality Assurance –

zWarranty and service

information

Warranty from Creative

Marketing & Consulting GmbH

Dear Customer,

The warranty for this equipment is

3years from the date of purchase. In the

event of product defects, you have legal

rights against the retailer of this product.

Your statutory rights are not affected in

any way by our warranty conditions,

which are described below.

zWarranty conditions

The warranty period begins on the date

of purchase. Please retain the original

sales receipt. This document is required

as your proof of purchase.

Should this product show any defect

in materials or manufacture within

3years from the date of purchase, we

will repair or replace it – at our dis-

cretion – free of charge. This warranty

service requires that you retain proof of

purchase (sales receipt) for the defective

device for the three year period and that

you brieﬂy explain in writing what the

fault entails and when it occurred.

If the defect is covered by our warranty,

we will repair and return your product

or send you a replacement. The original

warranty period is not extended when a

device is repair or replaced.

zWarranty period and

statutory claims for

defects

The warranty period is not extended

by the guarantee. This also applies to

replaced and repaired parts. Any dam-

ages or defects detected at the time of

purchase must be reported immediately

after unpacking. Any incidental repairs

after the warranty period are subject to

a fee.

zExtent of warranty

This device has been manufactured

according to strict quality guidelines and

carefully inspected before delivery.

The warranty applies to material

and manufacturing defects only. This

warranty does not extend to product

parts, which are subject to normal wear

and tear and can thus be regarded as

consumable parts, or for damages to

fragile parts, e.g. switches, rechargea-

ble batteries or parts made

from glass.

This warranty is voided if the product

becomes damaged or is improperly

used or maintained. For proper use

Stránka sa načítava...

Parkside PISG 120 B3 Používateľská príručka

Súvisiace články

Ostatné dokumenty