YEELIGHT YL00461 Používateľská príručka

Yeelight Automatic Curtain

Opener

User Manual • Uživatelský manuál •

Užívateľský manuál • Használati utasítás •

Benutzerhandbuch

Dovozce | Dovozca | Uvoznik | Importőr

eD System, a.s., Novoveská

1262/95, 7900 Ostrava, Česká

republika, www.edsystem.cz

2

Warning

1. Important safety instructions. It is important for safety of persons to follow these

instructions. Save these instructions.

2. Children should be supervised to ensure that they do not play with the appliance.

3. Do not allow children to play with fixed controls. Keep remote controls away form

children.

4. Frequently examine the installation for imbalance and signs of wear or damage to

cables springs and fixings. Do not use if repair or adjustment is necessary.

5. Warning: The drive shall be disconnected from its power source during cleaning,

maintenance and when replacing parts.

6. Warning: Important safety instructions. Follow all instructions, since incorrect

installation can lead to sever injury.

7. Before installing the drive, remove any unnecessary cords and disable any equipment

not needed for powered operation.

8. Install the actuating member of a manual release at a height less than 1.8 m.

9. That the characteristics of the driven part must be compatible with the rated torque

and rated operating time.

10. Fixed controls must be clearly visible after installation.

11. This appliance is not intended for use by persons (including children with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning use of the appliance by a

person responsible for their safety. (For non-EU & UKCA market).

12. This appliance can be used by children aged from 8 years and above and person with

reduced physical, sensory or mental capabilities or lack of experience and knowledge

if they have been given supervision or instruction concerning use of the appliance in a

safe way and understand the hazards involved. (For EU & UKCA market)

13. Cleaning and user maintenance shall not be made by children without supervision.

14. The product contains rechargeable lithium battery, which is harmful to the

environment when it is discarded. Please take the battery out of the battery pack

before discarding. Pry along the dividing line of the battery pack and remove the

battery. Removed batteries should be disposed of by a professional recycling

organization.

15. Under normal use of condition, this equipment should be kept a separation distance

of at least 20cm between the antenna and the body of the user.

16. The mass and the dimension of the driven part shall be compatible with the rated

torque and rated operating time.

3

Top cover

Driving

wheel

Indicator light

Setting key

Removable battery

compartment

Hub & Remote

Indicator light

Velcro hook

Velcro loop

Hub & Remote

Type-C

connector

Type-C charging

port

Introduction

Yeelight Automatic Certain Opener is a smart curtain controller. The product is small in size

and easy to install. It can realize the smart control of traditional curtains without replacing the

original curtain track. The product has a built-in lithium battery and comes with a Hub &

Remote, which can quickly access the voice platform to realize functions, such as App remote

control, voice-control to open and close curtains, and interact with other smart devices

connected to the smart platform. In addition, users can also quickly operate the four buttons

on the Hub & Remote (full on, full off, pause and custom: one-button start and move to a

designated position).

Accessories List

USB to Type-C power cable

x 1

Velcro hook x 2

Velcro loop x 2

Anti-fall bracket

Single panel: 2

Double panel: 4

4

Bead clip

Single panel: 8

Double panel: 16

Beads

Single panel: 2m

Double panel: 4m

Tip: Due to the update and upgrade of the product, the actual product may be slightly

different from the schematic diagram, please refer to the actual product.

Instructions

Instructional video

Please scan the QR code to view the instructional video or follow the steps to install and use

it.

Tip: In order to ensure the installation effect of the product, please wipe the surface of the

curtain track to remove the dust on the surface before installation.

Scan to code to view the instructional video.

Guide for first time use

1. Support smartphones and tablets with Android 4.4 & iOS 10.0 and above.

2. Scan the below QR code or search in APP store or Google to download “Mi Home”

App.

3. Open Mi Home APP and register a “Mi Home” account or log in directly if you have

an account.

4. Connect your phone to the internet. Please ensure that the Wi-Fi network is available

and can access the internet normally (the product does not support 5G network)

5. Take out the Hub & Remote and connect the power cable and adapter (the adapter

needs to be configured by yourself, DC5V 1A with USB port.

6. Remove the battery compartment of Yeelight Automatic Curtain Opener, remove the

battery separator, install the battery compartment again, and charge the Yeelight

5

Alexa, close the curtain

OK Google, close my bedroom curtain

There needs to be tight-fitting trim

seals on both sides of the rod

Suitable for telescopic Roman rod

(O-track)

Automatic Curtain Opener for the first time for more than 3 hours, until the white

indicator stops flashing (it takes about 6 hours to fully charge)

7. Open the “Mi Home” APP, click “+” in the upper right corner of the home page, and

add devices according to the APP prompts; Note: Please set the route after installing

the product on the track accurately, see the next page for the installation instruction.

Tip: Due to the upgrade and update of the “Mi Home” APP, the actual operation may

be slightly different from the above description, please operate according to the

current “Mi Home” APP.

8. You can link multiple third-party services to your Mi Home account.

Installation

Yeelight Automatic Curtain Opener (O-shaped track) only support O-shaped curtain track.

The cross-section of the curtain track and the matching size are shown in the figure below.

Notice:

 If you need to install it on I-shaped and C-shaped tracks, please purchase the

corresponding version of Yeelight Automatic Curtain Opener and are reference only.

Due to the update and upgrade of the product, the actual product may be slightly

different from the schematic diagram, please refer to the actual product.

The diameter of the rod should be between 16-40mm, or the perimeter should be between

51-125mm, whichever meets one of the two.

6

The second

hanging ring

The third

hanging

ring

Suitable for grommet curtains. When it is

used for grommet curtains, please make

sure the shortest distance between the

adjacent grommets is more than 90mm.

Suitable for ring top curtains. When it is

used for ring top curtains, please make sure

that the thickness of the hanging ring is

more than 4mm.

Install the automatic curtain opener on the track

Pull the top cover of the curtain motor upward to the maximum position, install the curtain

motor to the opening direction of the Roman rod (O-track) curtain, and in the middle of the

second and third grommet, let the top cover of the curtain motor and the driving wheel be

clamped on the track.

In order to prevent the curtain motor from falling during abnormal movement due to the

pattern or deformation of the curtain track, it is recommended to install an anti-fall bracket.

Diameter: 16-40mm

Perimeter: 51-125mm

plum-shaped

square

Not suitable for Roman rods (O-track) with non-circular section.

7

Opening direction of curtain

The third hanging ring The second hangning ring

The third hanging ring

Indoor view

Grommet curtains

Rip top curtains

The second hanging

ring

Same distance N

Reset it and the installation is complete.

Accessories for grommet curtains (not required for ring top curtains)

Because the inner diameter of the Roma ring of grommet curtain is similar to the outer

diameter of the Roman rod (O-shaped track), and it is difficult to pull (completely open the

curtain at one time) due to its structure, it is necessary to add the accessories to make the

curtain evenly distributed, which can reduce the pulling force and maintain the beauty of the

curtain.

1. Please close the curtain completely and make sure the distances between each folf life

are about the same.

8

How to open the clip

straighten

2. Take out the accessories, install the beads onto the bead clip as shown in the figure

below (make sure that there are two beads in the end of the clip)

3. Measure the distance N between two adjacent fold lines.

4. Straighten the beads, install the beads onto the second bead clip according to the

measured distance, and ensure that the distance between the first clip and the second

clip is N. Based on the distance between the first and second clips, find the positions

for the other bead clips, ensuring that the distance between each clip are the same

and are N.

5. Attach the clips to the outward facing curtain fold line. During installation, the clip

needs to be placed at the top area of the curtain, and only needs to be clamped at

the first few curtain protrusions from the fully closed direction to the fully open

direction.

6. When installing all the clips onto the curtain, please try to open and close it and make

sure the beads strip is straightened when closed. You can cut the rest strip off or hide

it behind the curtain.

9

Automatic curtain opener Beads

Curtain

The Roman rod

(O-shaped track)

First clip

Opening direction of curtain

Indoor direction

Automatic curtain opener Beads

The Roman rod

(O-shaped track)

Curtain

First clip

Opening direction of curtain

Indoor direction

Case 1: The first opening in the opening direction of the curtain faces the outside.

Case 2: The first opening in the opening direction of the curtain faces the indoors.

Hub & Remote Instructions

In order to ensure that the curtain motor can be used normally and can be connected to the

third-party platform, the hub remote control needs to be connected to the adapter (prepared

by yourself) before using the curtain motor, and it should be always powered on and can be

connected to Wi-Fi normally.

You can stick the Hub & Remote on a clean, flat, and stable surface such as the bedside table

or the wall.

1. Take out the Velcro loop from the accessories package and remove the isolation

paper on the back.

2. Paste the Velcro loop into the groove on the back of the Hub & Remote and press it

for 1 minute to ensure that the self-adhesive is cured.

3. Confirm where you want to paste and wipe the surface with a clean cloth.

4. Paste the Velcro hook to the loop, then remove the isolation paper behind the Velcro

hook, paste the entire Hub & Remote to the selected location, and press It for 1

minute to ensure that the self-adhesive is cured.

10

Notice:

 Do not press the button of the Hub & Remote during the whole process.

 The hub only supports Yeelight automatic curtain opener.

Instructions to the Hub Remote Control Buttons

Custom button: Move the curtain to the set position, which can be set in the App.

Pause button: Curtain stops moving.

Fully open button: Fully open the curtains.

Fully closed button: Fully close the curtains.

Note: The remote control will take effect only after the Yeelight Automatic Curtain Opener

completes the calibration settings. For the calibration process, please refer to the installation

guide in the App.

Auto Calibration Settings

Single panel curtain auto calibration

1. Place the automatic curtain opener to the position where the curtain is fully closed.

2. Quickly click the fully closed button on the Hub & Remote for 5 times. At this time,

the indicator lights of the Hub & Remote and the automatic curtain opener start to

flash blue slowly, indicating that both the automatic curtain opener and the Hub &

Remote are in the auto calibration mode.

11

Curtain fully closed

About 10cm

Automatic curtain opener starts auto-running at this point

Certain fully open

3. Gently pull the curtain about 10cm in the fully open direction, and the automatic

curtain opener will automatically move in the fully open direction. After the curtain

stops moving or moves to the designated position, click the fully closed button again.

4. The blue indicators of the automatic curtain opener and Hub & Remote stops

flashing.

5. Complete the auto calibration.

12

No gap between the left and right curtains

Auto-calibration of double panel curtains:

Refer to the route setting method of single panel curtain and set the routes of the left and

right Yeelight Automatic Curtain Opener respectively.

Note: When pulling the curtains by hand, please pull the left and right curtains about 10cm to

the full open direction in turn, after the curtain motors on the left and right sides reach both

ends of the curtain track or move to the designated position, click the full closed button on

the remote control again.

Warning:

1. The product is not a toy, pleas keep children away from it.

2. Only for indoor use, please do not use it outdoors.

3. The product is not moisture-proof, please do not spill water or other liquids product.

4. Please keep the product away from heat.

5. If the product fails during use, please hand it over to authorized professionals for

repair, and do not attempt to repair it by yourself.

13

Group the Yeelight Atomatic Curtain Opener and Hub &

Remote

(Please do it when the blue indicator on the motor flashes)

1. Press and hold the button of the automatic curtain opener that needs to be grouped

for 5s, until the blue indicator starts to flash.

2. Press and hold the fully open button and pause button of the Hub & Remote for 10s,

until the blue indicator on the Hub & Remote starts to flash.

3. After the automatic curtain opener and the gateway remote control are grouped

together, the automatic curtain opener will drive the curtain to move the left and right

for a short distance, and at the same time the blue indicators of the automatic curtain

opener stop flashing.

4. If the blue indicator of the Hub & Remote stops flashing, but the blue indicator on the

automatic curtain opener is still flashing, please repeat the above steps until both the

blue indicators of the automatic curtain opener and Hub & Remote stop flashing

which mean s the grouping is successful.

Button Instructions

Automatic curtain

opener

Buttons operation

Instruction

Press and hold the button for 5s

Enter the automatic curtain

opener and Hub & Remote

group mode

Click or press and hold the

button for less than 5s

Automatic curtain opener

stops moving

Hub & Remote

Buttons operation

Instruction

Custom button

Move the curtain to the set

position, you can set any

position in the APP

Fully open button

Fully open the curtains

Fully closed button

Fully close the curtains

Pause button

Automatic curtain opener stops

moving

Press and hold the pause + full open

button at the same time for 10s

Enter the automatic curtain

opener and Hub & Remote

group mode

Press and hold the custom + fully

closed button at the same time for 3s

The Hub & Remote enters the

distribution network to add to

the account mode

Quickly click the fully closed button 5

times in succession

Automatic curtain opener and

Hub & Remote enter auto-

calibration mode

14

Indicator Instructions

Automatic curtain opener

Buttons operation

Instruction

White indicator keeps on for

1s

Power on the automatic

curtain opener

White indicator flashes once

Click the button

Blue indicator flashes quickly

Group mode with Hub &

Remote

Blue indicator flashes slowly

Automatic curtain opener

enters auto-calibration

mode

Hub & Remote

Buttons operation

Instruction

White indicator keeps on for 1s

Power on the Hub & Remote

White indicator flashes slowly

Detect network

White indicator flashes quickly

The Hub & Remote enters the

networking and add to the

account mode

Blue indicator flashes quickly

Group mode with automatic

curtain opener

Blue indicator flashes slowly

Hub & Remote enters auto-

calibration mode

The blue indicator flashes once

The automatic curtain opener

hasn’t set the route

Charging Instructions

Insert the Type-C plug of the USP charging cable into the charging port on the Yeelight

Automatic Curtain Opener or remove the battery pack behind the Yeelight Automatic Curtain

Opener separately, and insert the other end into the adapter to charge.

Automatic curtain opener

Buttons operation

Instruction

White indicator flashes

Charging

White indicator keeps on

Charging is complete and

the adapter is not removed

15

Reset to factory settings

Press and hold the custom and fully closed buttons on the Hub & Remote at the same time

for 3 seconds until the white indicator of the Hub & Remote starts to flash, which means that

the Hub & Remote has been reset to the factory settings.

Warning:

After resetting to factory settings, you may lose all settings and you will need to re-add the

device to the account and re-calibrate the route.

Specifications

Automatic curtain opener

Model

YLCDJ-0009

Dimension

79 x 166 x 72mm

Rated torque

0.2N m

Working time

S2 4min

Rated voltage

5V

Rated power

6W

Movement speed

7cm/s

Test conditions: Performance mode, 2m curtain track, 12kg curtain, 25°C (The test results are

from the control experiment of Yeelight laboratory, the battery life may vary due to different

conditions).

Hub & Remote

Model YLCDJ-0011

Dimension 65 x 65 x 18mm

Rated voltage 5V

Rated current 1A

Notes:

1. For indoor use only.

2. It is recommended to be used at an altitude of less than 2000meters for safety.

3. “ ” The symbol indicates direct current (DC).

Compatible with: Android id 4.4 or iOS 10.0 and above.

Wireless Connectivity: Wi-Fi IEEE 802.11b/g/n 2.4GHz. Bluetooth 4.2BLE, Zigbee

Operating Frequency: 2412-2472MHz (Wi-Fi), 2402-2480MHz (BT), 2405-2480MHz (Zigbee)

Maximum Output Power: 16.24 dBm (Wi-Fi), 2dBm (BT), 6.06dBm (Zigbee).

16

EU Declaration of Conformity

Quingdao Yeelink Information Technology Co., hereby declares that type Y00409 devices are in conformity

with EU Directives. The full text of the EU Declaration of Conformity is available at the following web

address: https://edshop.edsystem.cz/prohlaseni-o-shode/article-28393

WEEE

This product must not be disposed of as normal household waste in accordance with the EU Directive on

Waste Electrical and Electronic Equipment (WEEE - 2012/19 / EU). Instead, it shall be returned to the place

of purchase or handed over to a public collection point for the recyclable waste. By ensuring this product

is disposed of correctly, you will help prevent potential negative consequences for the environment and

human health, which could otherwise be caused by inappropriate waste handling of this product. Contact

your local authority or the nearest collection point for further details. Improper disposal of this type of

waste may result in fines in accordance with national regulations.

17

Varování

1. Důležité bezpečnostní pokyny. Pro bezpečnost osob je důležité dodržovat tyto

pokyny. Tyto pokyny si uložte.

2. Děti by měly být pod dohledem, aby si se spotřebičem nehrály.

3. Nedovolte dětem, aby si hrály s pevnými ovládacími prvky. Dálkové ovladače

uchovávejte mimo dosah dětí.

4. Často kontrolujte instalaci, zda není nevyvážená a zda nejeví známky opotřebení nebo

poškození pružin kabelů a upevňovacích prvků. Pokud je nutná oprava nebo seřízení,

nepoužívejte je.

5. Varování: Při čištění, údržbě a výměně dílů musí být pohon odpojen od zdroje

napájení.

6. Varování: Důležité bezpečnostní pokyny. Dodržujte všechny pokyny, protože

nesprávná instalace může vést k vážnému zranění.

7. Před instalací jednotky odstraňte všechny nepotřebné kabely a vypněte všechna

zařízení, která nejsou potřebná pro napájený provoz.

8. Ovládací prvek ručního uvolňovače instalujte ve výšce menší než 1,8 m.

9. Vlastnosti poháněné části musí odpovídat jmenovitému krouticímu momentu a

jmenovité době provozu.

10. Pevné ovládací prvky musí být po instalaci jasně viditelné.

11. Tento spotřebič není určen k používání osobami (včetně dětí se sníženými fyzickými,

smyslovými nebo duševními schopnostmi nebo s nedostatkem zkušeností a znalostí,

pokud jim osoba odpovědná za jejich bezpečnost neposkytla dohled nebo je

nepoučila o používání spotřebiče. (Pro trh mimo EU a UKCA).

12. Tento spotřebič mohou používat děti od 8 let a starší a osoby se sníženými fyzickými,

smyslovými nebo duševními schopnostmi nebo s nedostatkem zkušeností a znalostí,

pokud jsou pod dohledem nebo byly poučeny o bezpečném používání spotřebiče a

rozumí souvisejícím nebezpečím. (Pro trh EU a UKCA)

13. Čištění a uživatelskou údržbu nesmí provádět děti bez dozoru.

14. Výrobek obsahuje dobíjecí lithiovou baterii, která je při likvidaci škodlivá pro životní

prostředí. Před vyhozením vyjměte baterii z akumulátoru. Vypačte podél dělící čáry

bateriového bloku a baterii vyjměte. Vyjmuté baterie by měly být zlikvidovány

odbornou recyklační organizací.

15. Při běžném používání tohoto zařízení by měla být vzdálenost mezi anténou a tělem

uživatele nejméně 20 cm.

16. Hmotnost a rozměry poháněné části musí odpovídat jmenovitému točivému

momentu a jmenovité době provozu.

18

Úvod

Yeelight Automatic Curtain Opener je chytrý ovladač záclon. Výrobek má malé rozměry a

snadno se instaluje. Dokáže realizovat inteligentní ovládání tradičních záclon bez nutnosti

výměny původní záclonové dráhy. Výrobek má vestavěnou lithiovou baterii a je dodáván s

rozbočovačem a dálkovým ovladačem, který umožňuje rychlý přístup k hlasové platformě pro

realizaci funkcí, jako je dálkové ovládání aplikace, hlasové ovládání pro otevírání a zavírání

záclon a interakce s dalšími chytrými zařízeními připojenými k chytré platformě. Kromě toho

mohou uživatelé také rychle ovládat čtyři tlačítka na dálkovém ovladači Hub & Remote (úplné

zapnutí, úplné vypnutí, pozastavení a vlastní: spuštění jedním tlačítkem a přesun do určené

polohy).

Seznam příslušenství

Napájecí kabel z USB na

Typ-C x 1

Háček na suchý zip x 2

Smyčka na suchý zip x 2

Držák proti pádu

Jednoduchý panel: 2

Dvojitý panel: 4

Horní kryt

Hnací kolo

Vyjímatelná přihrádka na baterie

Kontrolka

Nastavení klíče

Nabíjecí port typu C

Rozbočovač

a dálkové ovládání

Kontrolka

Háček na suchý zip

Smyčka na suchý zip

Rozbočovač a dálkové ovládání

Konektor typu C

19

Korálkový klip

Jednoduchý panel: 8

Dvojitý panel: 16

Korálky

Jednoduchý panel: 2 m

Dvojitý panel: 4 m

Tip: V důsledku aktualizace a upgradu výrobku se může skutečný výrobek mírně lišit od

schématu, viz skutečný výrobek.

Pokyny

Instruktážní video

Naskenováním QR kódu zobrazte instruktážní video nebo postupujte podle pokynů k

instalaci a používání.

Tip: Aby byl zajištěn účinek instalace výrobku, otřete před instalací povrch záclonové dráhy,

abyste odstranili prach na povrchu.

Naskenováním kódu zobrazíte instruktážní video.

Příručka pro první použití

1. Podpora chytrých telefonů a tabletů se systémem Android 4.4 a iOS 10.0 a novějším.

2. Stáhněte si aplikaci "Mi Home" naskenováním níže uvedeného QR kódu nebo

vyhledáním v obchodě APP store či Google.

3. Otevřete aplikaci Mi Home APP a zaregistrujte si účet "Mi Home" nebo se přímo

přihlaste, pokud účet máte.

4. Připojte telefon k internetu. Ujistěte se, že je k dispozici síť Wi-Fi a že můžete

normálně přistupovat k internetu (výrobek nepodporuje síť 5G).

5. Vyjměte rozbočovač a dálkové ovládání a připojte napájecí kabel a adaptér (adaptér je

třeba nakonfigurovat samostatně, DC5V 1 A s portem USB.

6. Vyjměte přihrádku na baterie automatického otvírače záclon Yeelight, vyjměte

oddělovač baterií, znovu nainstalujte přihrádku na baterie a poprvé nabíjejte

automatický otvírač záclon Yeelight déle než 3 hodiny, dokud nepřestane blikat bílý

indikátor (úplné nabití trvá přibližně 6 hodin).

20

Alexo, zatáhni závěs

OK Google, zatáhni mi závěs v ložnici.

Na obou stranách tyče musí být těsně

přiléhající těsnění.

Vhodné pro teleskopickou římskou tyč

(O-track)

7. Otevřete aplikaci "Mi Home", klikněte na tlačítko "+" v pravém horním rohu

domovské stránky a přidejte zařízení podle pokynů aplikace;

Poznámka: Po instalaci produktu na trati přesně nastavte trasu, viz další stránka s

pokyny k instalaci.

Tip: V případě, že je zařízení v provozu, je nutné jej nainstalovat: Z důvodu aktualizace

a upgradu aplikace "Mi Home" APP se může skutečné ovládání mírně lišit od výše

uvedeného popisu, ovládejte se prosím podle aktuální aplikace "Mi Home" APP.

8. K účtu Mi Home můžete připojit více služeb třetích stran.

Instalace

Automatický otvírač záclon Yeelight (kolejnice ve tvaru O) podporuje pouze kolejnice ve tvaru

O. Průřez záclonové dráhy a odpovídající velikost jsou uvedeny na obrázku níže.

Upozornění:

 Pokud jej potřebujete nainstalovat na kolejnice ve tvaru I a C, zakupte si odpovídající

verzi automatického otvírače záclon Yeelight. Z důvodu aktualizace a upgradu

výrobku se může skutečný výrobek mírně lišit od schématu, podívejte se prosím na

skutečný výrobek.

Průměr tyče by se měl pohybovat v rozmezí 16-40 mm nebo obvod by měl být v rozmezí 51-

125 mm, podle toho, co splňuje jednu z těchto dvou podmínek.

Stránka sa načítava...

YEELIGHT YL00461 Používateľská príručka

YEELIGHT YL00461 Používateľská príručka

v iných jazykoch

Ostatné dokumenty