Radiodetection Discontinued Products Používateľská príručka

RD7100

™

Utility cable and pipe locator range

User guide

Bedienungsanleitung

Gebruikershandleiding

Guía del usuario

Guide d’utilisation

用户指南

Uživatelská příručka

90/UG103INT/07

 

2

ENGLISH 3

NEDERLANDS 43

ESPAÑOL 63

FRANÇAIS 83

DEUTSCH 23

中文 103

ČESKÝ 123

رع

142

3

ENGLISH

Preface

About this guide

CAUTION: This guide provides basic operating instructions for the RD7100

locator and transmitter. It also contains important safety information and

guidelines and as such should be read in its entirety before attempting to

operate the RD7100 locator and transmitter.

This guide is intended as a quick reference guide only. For detailed instructions,

including the use of accessories, help with eCert

™

, CALSafe

™

and usage-logging*

please refer to the RD7100 locator Operation Manual and RD Manager

™

manuals,

which are available for download from www.radiodetection.com.

The online User Manual library also contains links to the SurveyCERT+ and

RD Manager manuals.

Certiﬁcates of conformity for the RD7100 locators and Tx transmitter ranges can be

found at www.radiodetection.com.

*Logging and GPS models only

4

WARNING! Direct connection to live conductors is POTENTIALLY LETHAL.

Direct connections to live conductors should be attempted by fully qualiﬁed

personnel only using the relevant products that allow connections to energized

lines.

WARNING! The transmitter is capable of outputting potentially lethal voltages.

Take care when applying signals to any pipe or cable and be sure to notify other

technicians who may be working on the line.

WARNING! Reduce audio level before using headphones to avoid damaging

your hearing.

WARNING! This equipment is NOT approved for use in areas where

hazardous gases may be present.

WARNING! When using the transmitter, switch off the unit and disconnect

cables before removing the battery pack.

WARNING! The RD7100 locator will detect most buried conductors but there

are some objects that do not radiate any detectable signal. The RD7100, or any

other electromagnetic locator, cannot detect these objects so proceed with

caution. There are also some live cables which the RD7100 will not be able to

detect in Power mode. The RD7100 does not indicate whether a signal is from a

single cable or from several in close proximity.

WARNING! Batteries can get hot after prolonged use at full output power.

Take care while replacing or handling batteries.

WARNING! Only use charging equipment provided by Radiodetection. The use of

alternative chargers may cause a safety hazard and/or reduce the life of the battery.

CAUTION: Do not let your battery completely discharge as this may reduce its life

or damage it permanently. If you are not using your equipment for a long period

do charge them at least once a month.

WARNING! Batteries can get hot after prolonged use at full output power.

Take care while replacing or handling batteries.

WARNING! Do not tamper with, or attempt to disassemble the battery packs.

CAUTION: If battery failure is suspected or if the battery shows any sign of

discoloration / physical damage return the entire unit to an authorized repair

center for investigation and repair. Local, national or IATA transport regulations

may restrict the shipment of faulty batteries. Check with your courier for

restrictions and best practice guidelines. Your local Radiodetection representative

will be able to direct you to our authorized repair centers.

NOTE: The charging temperature range is 0 to 45 °C, 32 to 113°F. Do not attempt

to recharge your batteries outside this temperature range.

5

ENGLISH

3 Year Extended Warranty

RD7100 locators and transmitters are covered by a 1 year warranty as standard.

Customers can extend their warranty period to a total of 3 years by registering

their products within 3 months of purchase.

There are 2 ways to register your product:

1. Radiodetection portal

Visit https://portal.radiodetection.com to create your portal account* and use

the Product page to register your locator or transmitter.

Visit https://support.radiodetection.com for instructions on how to create a

portal account or register your product.

* A valid email address and mobile number are required.

2. Windows Applications

RD Manager

™

available from www.radiodetection.com/RDManager.

From time to time Radiodetection may release new software to improve the

performance or add new functionality to its products. By registering, users will

beneﬁt from email alerts advising about new software and special offers related

to its product range.

Users can opt-out at any time from receiving software and technical notiﬁcations,

or just from receiving marketing material by contacting Radiodetection.

eCert and Self-Test

The RD7100 locator is safety equipment which should be regularly checked to

ensure its correct operation.

eCert provides a thorough test of the RD7100’s locating circuitry, and supplies a

Radiodetection Calibration Certiﬁcate when a positive test result is obtained.

To run an eCert, the locator should be connected to an internet-enabled PC on

which the RD Manager software is installed.

Refer to the RD Manager operation manual for further details. Additional purchase

may be required.

RD7100 locators incorporate an Enhanced Self-Test feature. In addition to the

typical checks for display and power functions, the RD7100 locator applies test

signals to its locating circuitry during a Self-Test to check accuracy and performance.

We recommend that a self-test is run at least weekly, or before each use.

6

RD7100 locator

1

2

3

4

5

6

8

7

13

14 1515

9

10

11

12

11

26

29

28

30

31

16

17

18

19

20

21 22 2427 2523

12 or more satellites locked

9-11 satellites locked

6-8 satellites locked

3-5 satellites locked

GPS satellite lock acquired

GPS

active, seeking satellite lock

7

ENGLISH

Locator features

1. Keypad

2. LCD with auto backlight.

3. Speaker.

4. Battery compartment.

5. Optional Lithium-Ion battery pack.

6. Accessory connector.

7. Headphone connector.

8. USB port

(inside battery compartment).

Locator keypad

9. Power key.

10. Frequency key.

11. Up and down arrows.

12. Antenna key.

Locator screen icons

13. Signal strength bargraph with peak

marker.

14. Signal strength readout.

15. Null / Proportional Guidance arrows.

16. Battery level.

17. Sensitivity readout

18. Volume level.

19. Radio Mode icon.

20. Power Mode icon.

21. Accessory / Measurement icon.

22. A-Frame icon.

23. Frequency / current / menu readout.

24. Antenna modes icon:

Indicates antenna mode selection:

Peak/Peak+

™

/Null/Guidance.

25. Sonde icon: Indicates that a sonde

signal source is selected.

26. Line icon: Indicates that a line signal

source is selected.

27. Compass: Shows the orientation

of the located cable or sonde relative

to the locator.

28. Transmitter standby indicator.

29. Depth readout.

GPS equipped locators only:

30. GPS Status.

31. GPS Signal quality.

8

Tx-1, Tx-5 and Tx-10 transmitters

1

3

4

2

10

11

12 13 14

15

16

17

18

19

5

6

7

8

9

ENGLISH

Transmitter features

1. Keypad.

2. LCD.

3. Removable accessory tray.

4. D-cell battery tray.

5. Optional Lithium-Ion battery pack.

Transmitter keypad

6. Power key.

7. Frequency key.

8. Up and down arrows.

9. Measure key.

Transmitter screen icons

10. Battery level indicator.

11. Operation mode readout.

12. Standby icon.

13. Output level indicator.

14. Clamp icon: Indicates when a signal

clamp or other accessory is connected.

15. DC Power connected indicator.

16. Induction mode indicator.

17. A-Frame: Indicates when the

transmitter is in Fault-Find Mode.

18. Voltage warning indicator: Indicates

that the transmitter is outputting

potentially hazardous voltage levels.

19. Volume level indicator.

10

Keypad actions and shortcuts

Switch the locator or transmitter on by pressing the key. Once powered up, the keys

function as follows:

Locator keys

KEY

● SHORT PRESS

●■■■● LONG PRESS

Enter the menu. Switch power off.

Scroll through locate frequencies

from low to high.

–

When using active frequencies:

Toggles Peak, Peak+, Null, and Guidance

antenna modes.

PL & PLG models in Power Mode:

Scrolls through Power Filters

™

for improved

discrimination of parallel or strong power

signals.

In Peak+ antenna mode:

Switch between Guidance and Null arrows.

and

Increase and decrease gain.

RD7100 automatically sets gain to

mid-point when pressed.

Rapidly increase and decrease gain steps

in 1dB increments.

KEY

● SHORT PRESS

●■■■● LONG PRESS

Enter the menu. Switch Power off.

Scroll through locate frequencies

from low to high.

–

Take voltage and impedance measurements

using the currently selected frequency.

Take voltage and impedance

measurements at a standardized frequency.

and

Adjusts the output signal.

Select standby

/ maximum standard

power

.

Transmitter keys

Tip: to scroll through frequencies from high to low, hold while pressing the button

(applies to both locators and transmitters).

11

ENGLISH

Before you begin

IMPORTANT!

This guide is intended to be a quick reference guide. We recommend you read the

full operation manual before you attempt to operate the RD7100 locator.

First use

The RD7100 locators and transmitters can be powered by D-cell alkaline batteries, D-cell

NiMH batteries, or by an accessory Lithium-Ion (Li-Ion) battery pack.

To ﬁt the D cell batteries in the locator, open the battery compartment and insert two

D-Cell Alkaline or NiMH batteries, taking care to align the positive (+) and negative (-)

terminals as indicated.

To ﬁt the D cell batteries in the transmitter, unlatch the accessory tray. The battery

compartment is located underneath the transmitter body. Use the turnkey to unlatch the

battery compartment. Insert eight D-Cell Alkaline or NiMH batteries, taking care to align

the positive (+) and negative (-) terminals as indicated.

Alternatively, you can power the transmitter from a mains or vehicle power source using a

Radiodetection supplied optional accessory adapter.

Rechargeable battery packs

Lithium-Ion battery packs are available for both locators and transmitters, providing

superior performance over traditional alkaline batteries. To ﬁt these rechargeable packs,

follow the instructions provided with each pack.

Checking your system software version

If you wish to check which version of software is running on your locator, press and

hold the

key when switching the locator on. This information may be asked for when

contacting Radiodetection or your local representative for technical support.

Transmitters automatically show their software version on startup.

System setup

It is important that you set up the system according to regional / operational requirements

and your personal preferences before you conduct your ﬁrst survey. You can set the

system up using the menus as described below.

Setting up your system

The RD7100 locator and transmitter menus allow you to select or change system options.

Once entered, the menu is navigated using the arrow keys. Navigation is consistent on both

the transmitter and the locator. When in the menu, most on-screen icons will temporarily

disappear and the menu options will appear in the bottom left-hand corner of the display.

The right arrow enters a submenu and the left arrow returns to the previous menu.

12

Note that when browsing the locator menu, the

and keys act as left and right arrows.

When browsing the transmitter menu, the

and

keys act as left and right arrows.

To navigate menus:

1. Press the key to enter the menu.

2. Use the

or

keys to scroll through the menu options.

3. Press the

key to enter the option’s submenu.

4. Use the

or

keys to scroll through the submenu options.

5. Press the

key to conﬁrm a selection and return to the previous menu.

6. Press the

key to return to the main operation screen.

NOTE: When you select an option and press the

key, the option will be enabled

automatically.

Locator menu options

• VOL: Adjust the speaker volume from 0 (mute) to 3 (loudest).

• GPS: Enable or disable the internal GPS module and enable/disable SBAS GPS

augmentation (GPS models only).

• UNITS: Select metric or imperial units.

• INFO: Run a Self-Test, display the date of the most recent service recalibration

(M CAL) or the most recent eCert calibration.

• LANG: Select menu language.

• POWER: Select local power network frequency: 50 or 60Hz.

• ANT: Enable or disable any antenna mode with the exception of Peak.

• FREQ: Enable or disable individual frequencies.

• ALERT: Enable or disable StrikeAlert™.

• BATT: Set battery type: Alkaline or NiMH. Li-Ion auto-selects when connected.

• ARROW: Select Null or proportional Guidance arrows in Peak+ mode

• COMP: Enable or disable display of the Compass feature.

Transmitter menu options

• VOL: Adjust the speaker volume from 0 (mute) to 3 (loudest).

• FREQ: Enable or disable individual frequencies.

• BOOST: Boost transmitter output for a speciﬁed period of time (in minutes).

• LANG: Select menu language.

• OPT F: Run SideStepauto

™

to auto-select a locate frequency for the connected utility.

• BATT: Set battery type: ALK, NiMH or Li-Ion and enable / disable Eco mode.

• MAX P: Set the transmitter to output its maximum wattage.

13

ENGLISH

• MODEL: Match the transmitter setting to the model of your locator.

• MAX V: Set the output voltage to maximum (90V).

Examples of using the menu, selecting options and

making changes:

Locator mains power frequency

To select the correct frequency (50 or 60Hz) for your country or region’s power supply:

1. Press the

key to enter the menu.

2. Scroll to the POWER menu using the

or

keys.

3. Press the

key to enter the POWER menu.

4. Use the

or

keys to select the correct mains frequency.

5. Press the

key twice to accept your selection and return to the main operation

screen.

Batteries

It is important to set the system to match the currently installed battery type to ensure

optimal performance and correct battery level indication.

To set your battery type:

1. Press the

key to enter the menu.

2. Scroll to the BATT menu using the

or

arrows.

3. Press the

key (locator) or the key (transmitter) to enter the BATT menu.

4. Scroll up or down to select the correct battery type (Alkaline, Nickel-metal Hydride

or Lithium-Ion). Lithium-Ion is automatically selected when a Li-Ion pack is connected

to a locator.

5. Press the

key twice to accept your selection and return to the main operation screen.

Transmitter Eco Mode

When using alkaline batteries, Eco mode can be selected to maximize run time. When

Eco mode is selected the transmitter automatically reduces its maximum power output as

battery levels run low. Eco mode is switched off by default. To Enable Eco Mode:

1. Press the

key to enter the menu.

2. Scroll to the BATT menu using the

or

arrows.

3. Press the

key to enter the BATT menu.

4. Select the ALK Battery type using the

or

arrows.

5. Press the

key to enter the ECO sub menu

6. Select ECO using the

or

arrows.

7. Press the

key three times to accept your selection and return to the main

operation screen.

14

Locating pipes and cables

For more detailed descriptions of using the

locator and transmitter, and for detailed

locate techniques, refer to the Operation

Manual.

The RD7100 locator is designed to operate

with the ‘blade’ of the locator perpendicular

to the path of the cable or pipe being

located.

Running a Self-Test

We recommend that a Self-Test is run at least weekly, or before each use. As the Self-

Test tests the integrity of the locate circuity, it is important that it is carried out away from

larger metallic object such as vehicles, or strong electrical signals. To run a Self-Test:

1. Press the

key to enter the menu.

2. Scroll to the INFO menu using the

or

arrows.

3. Press the

key to enter the INFO menu.

4. Select TEST using the

or

arrows.

5. Press the

key to select YES

6. Press the

key to begin the Self-Test

7. Once the Self-Test is completed, the result (PASS or FAIL) will be displayed.

8. Restart the locator using the

key

SideStepauto™

The transmitter can be used to recommend a general-purpose locate frequency for the

intended locate task by measuring the impedance of the target cable or pipe. To run

SideStepauto

™

, connect the transmitter to the target utility, then:

1. Press the

key to enter the menu.

2. Scroll to the OPT F menu using the

or

arrows.

3. Press the

key to select ‘START.

4. Press the

key to start the test. The transmitter will automatically select a general

purpose frequency for use on the connected utility.

15

ENGLISH

Locating with Active Frequencies

Active frequencies are applied to the target pipe or cable using the transmitter, and

provide the most effective way of tracing buried pipes or cables.

Generally speaking, it is better to use a low frequency on larger, low impedance utilities,

and move to a higher frequency on smaller, high impedance utilities.

The lowest power setting required to trace the target utility should always be used to

minimize the risk of false trails.

The transmitter can apply a signal using three different methods:

Direct connection

In direct connection, you connect the transmitter directly to the pipe or cable you wish to

survey using the red Direct Connect lead supplied. The black lead is generally connected

to earth using the supplied ground stake.

The transmitter will then apply a discrete signal to the line, which you can trace using the

locator. This method provides the best signal on an individual line and enables the use of

lower frequencies, which can be traced for longer distances.

WARNING! Direct connection to live conductors is POTENTIALLY LETHAL. Direct

connections to live conductors should be attempted by fully qualiﬁed personnel only

using the relevant products that allow connections to energized lines.

Induction

The transmitter is placed on the ground over or near the survey area. You select the

appropriate frequency. The transmitter will then induce the signal indiscriminately to

any nearby metallic conductor. In induction mode, using higher frequencies is generally

recommended as they are induced more easily onto nearby conductors.

Transmitter Clamp

An optional signal clamp can be placed around an insulated live wire or pipe up to

8.5"/215mm in diameter to transfer the transmitter signal to the utility. This method of

applying the transmitter signal is particularly useful on insulated live wires and removes

the need to disconnect the supply to the cable.

WARNING! Do not clamp around uninsulated live conductors.

WARNING! Before applying or removing the clamp around a power cable ensure

that the clamp is connected to the transmitter at all times.

Locating with Passive Frequencies

Passive frequency detection takes advantage of signals that are already present on

buried metallic conductors. The RD7100 supports up to three types of passive

frequencies: Power, Radio and CPS* signals. You can detect these frequencies without

the aid of the transmitter.

*Model speciﬁc.

16

Power Filters

RD7100PL and PLG locators allows operators to take advantage of the harmonic signals

found on power networks. Once in Power Mode, press the

key to switch out of

Radiodetection’s sensitive Power Mode and scroll through ﬁve individual Power Filters.

This enables operators to establish if a single large power signal comes from one source

or from the presence of multiple cables. The different harmonic characteristics of the

detected lines can then be used to trace and mark their route.

Additionally the use of an individual harmonic can allow you to locate power lines in

situations where the total signal would otherwise be too large.

Locate Modes

Dependent on the model selected, the RD7100 offers a choice of up to 4 locate modes,

each of which is designed for speciﬁc uses, depending on what task is being carried out.

To scroll between locate modes, press the

key.

PEAK: For accurate locating, the peak bargraph provides a visual readout of the

signal strength. The peak signal is found directly over the buried utility.

PEAK+: Choose to combine the accuracy of the Peak bargraph with Null arrows,

which can indicate the presence of distortion, or with proportional Guidance

arrows for rapid line tracing – switch between them by holding the

key.

GUIDANCE: Proportional arrows and a ballistic ‘needle’ combine with audio

left/right indication for rapidly tracing the general path of a buried utility.

NULL: Provides a quick left/right indication of the path of a utility. As Null is

susceptible to interference, it is best used in areas where no other utilities

are present.

Depth, current and compass readouts

WARNING! Never use the depth measurement readout as a guide for

mechanical or other digging activity. Always follow safe digging guidelines.

The RD7100 locator can measure and display the utility depth, locate signal current and

the relative orientation of the cable or pipe to the locator. This helps you to make sure that

you are following the right cable or pipe, especially when other utilities are present.

The RD7100 locator features TruDepth

™

, a feature that helps you to ensure the accuracy

of your locates. The depth and current are automatically removed from the display when

the locator is at an angle of more than 7.5° from the path of the cable or pipe being

located, or when the locator determines that signal conditions are too poor for reliable

measurements.

17

ENGLISH

Using accessories

The locator and transmitter are compatible with a wide range of accessories. For detailed

information on using any of the accessories below please refer to the RD7100 locator

operation manual.

Transmitter signal clamps

When it is not possible to connect directly onto a pipe or cable, or induction mode is

unsuitable, a transmitter signal clamp may be used. The clamp is plugged into the output

of the transmitter and provides a means of applying a locate signal to an insulated live wire.

This is particularly useful with live insulated cables as it removes the need to disable the

power and break the line.

WARNING! Do not clamp around uninsulated live conductors.

WARNING! Before applying or removing the clamp around a power cable

ensure that the clamp is connected to the transmitter at all times.

To locate or identify individual lines a locator signal clamp can be connected to the

accessory socket of the locator and can be clamped around individual pipes or cables.

Stethoscopes and locator signal clamps

Locator clamps can be used to identify a target cable or pipe amongst a number of

different cables by checking for the strongest locate signal. When cables are bunched or

tightly packed, a stethoscope antenna can be used in place of a clamp.

To use a stethoscope or locator signal clamp, connect it to the locator’s accessory socket.

The locator will automatically detect the device and ﬁlter out location modes that are

irrelevant.

Sondes, Flexrods and FlexiTrace

Sondes are battery powered transmitters that are useful for tracing non-metallic pipes.

They can be ﬁxed to Flexrods to allow them to be pushed through pipes or conduits, and

some are suitable for blowing through ductwork. Some models of the RD7100 can detect

a range of sonde frequencies, including those transmitted by ﬂexiprobe

™

P540c pushrod

systems and P550c ﬂexitrax

™

crawlers.

For a detailed guide on locating sondes, please refer to the operation manual.

A FlexiTrace is a traceable ﬁberglass rod incorporating wire conductors with a sonde

at the end. It is connected to the output of the transmitter and is typically used in small

diameter, non-metallic pipes. The user has the option of locating the entire length of the

cable or choosing to locate only the tip of the cable.

The FlexiTrace has a maximum power rating of 1W. When using the FlexiTrace with a

Radiodetection Tx-5 or Tx-10 transmitter, the output limit must be set to 1W in the MAX P

menu and the output voltage limit set to LOW in the MAX V menu.

No additional settings are required for the Tx-1 transmitter.

18

Fault-ﬁnding with an A-Frame

The RD7100PL, PLG, TL and TLG models have the ability to detect cable or pipe

insulation faults accurately using an A-Frame accessory. The Tx-5 and Tx-10 transmitters

provide fault ﬁnding signals that can be detected by the A-Frame as a result of the signal

bleeding to ground through damaged cable sheaths.

The Transmitter’s multimeter function can be used to measure the impedance of the

connected pipe or cable in order to characterize the fault.

For a detailed guide to fault-ﬁnding, please refer to the operation manual.

Plug / Live cable connector

The plug connector is connected to the output of the transmitter and is used to put a

signal onto a line and trace it from a domestic mains plug to the service cable in the

street.

The live cable connector can be used to apply a signal to a live cable. Only suitably

qualiﬁed personnel should use this equipment.

Submersible antenna

This antenna is connected to the locator and used to locate pipes and cables underwater

at depths of up to 300 feet / 100 meters.

WARNING: use of the submersible antenna should be by fully licensed and

experienced personnel only, and only after fully reading the operation manual!

RD Manager PC Software

RD Manager is the RD7100 locator system PC companion, and it allows you to manage

and customize your locator. RD Manager is also used to retrieve and analyze survey and

usage data, run an eCert calibration, and to perform software upgrades.

You can use RD Manager to register your products to obtain an extended warranty, setup

your locator by performing a number of maintenance tasks such adjusting date and time,

activating and de-activating active frequencies, or by setting-up functions like CALSafe

or StrikeAlert.

RD Manager is compatible with PCs running Microsoft Windows 64 bit operating system.

To download RD Manager, go to www.radiodetection.com/RDManager.

If you do not have internet access, or wish to receive RD manager on a CD-ROM,

contact your local Radiodetection ofﬁce or representative.

For more information about RD Manager refer to the RD Manager operation manual.

19

ENGLISH

Automatic Usage-Logging

RD7100 locator models equipped with GPS offer a powerful data logging system which

records all the instrument’s critical parameters (including GPS position, if available) and

warnings in its internal memory every second.

The automatic logging system is always active and cannot be disabled. The locator’s

memory is capable of storing over 500 days of usage data, when used for 8 hours per day.

Logs can be retrieved using the RD Manager PC application for usage analysis and

survey validation. Refer to the RD Manager operation manual for further information.

GPS

The RD7100 locator can use an internal GPS module (GPS models only) to be able to

detect and store its latitude, longitude and accurate UTC time alongside its location data.

This positional information is then appended to the automatic usage-logging system.

The presence of GPS data allows for the data to be mapped easily and to export and

save the information directly into GIS systems.

GPS menu settings

There are 5 options in the GPS menu:

• INT: Select this to use the internal GPS if present.

• OFF: Select this to switch off the internal GPS module and save battery.

• SBAS: Set SBAS (Satellite-based augmentation systems) mode to improve GPS

accuracy. When ON the GPS system will take longer to lock.

• RESET: Select YES to reset the internal GPS (GPS models only).

CALSafe

GPS equipped RD7100 locators models are equipped with a system which can be

enabled to force them to shut down once they are beyond the expected service /

calibration date.

When the unit is within 30 days of the service due date the unit will display at startup the

number of days left. The locator will stop functioning on the service due date.

CALSafe is disabled by default. You can enable the CALSafe feature and edit the

CALSafe service / calibration due date using the RD Manager PC software. Refer to the

RD Manager operation manual for further information.

20

Training

Radiodetection provides training services for most Radiodetection products. Our qualiﬁed

instructors will train equipment operators or other personnel at your preferred location or

at Radiodetection headquarters. For more information go to www.radiodetection.com or

contact your local Radiodetection representative.

Care and maintenance

The RD7100 locator and transmitter are robust, durable and weatherproof. However you

can extend your equipment’s life by following these care and maintenance guidelines.

General

Store the equipment in a clean and dry environment.

Ensure all terminals and connection sockets are clean, free of debris and corrosion and

are undamaged.

Do not use this equipment when damaged or faulty.

Batteries and power supply

Only use the rechargeable battery packs, chargers and power supplies approved by

Radiodetection.

If not using rechargeable packs, use good quality Alkaline or NiMH batteries only.

Batteries should be disposed of in accordance with your company’s work practice,

and/or any relevant laws or guidelines in your country.

Cleaning

WARNING! Do not attempt to clean this equipment when it is powered or

connected to any power source, including batteries, adapters and live cables.

Ensure the equipment is clean and dry whenever possible.

Clean with a soft, moistened cloth. Do not use abrasive materials or chemicals as they

may damage the casing, including the reﬂective labels. Do not use high pressure jets of

water to clean the equipment.

If using this equipment in foul water systems or other areas where biological hazards may

be present, use an appropriate disinfectant.

Stránka sa načítava...

Radiodetection Discontinued Products Používateľská príručka

Tento návod je vhodný aj pre

Radiodetection Discontinued Products Používateľská príručka

v iných jazykoch

Ostatné dokumenty