Parkside PFBS 160 B2 Translation Of The Original Instructions

Kategória
Elektrické náradie
Typ
Translation Of The Original Instructions
IAN 281406
PRECISION MULTI-GRINDER PFBS 160 B2
PRECISION MULTI-GRINDER
Translation of the original instructions
FEINBOHRSCHLEIFER
Originalbetriebsanleitung
MULTICSISZOLÓ
Az originál használati utasítás fordítása
BRUSILNIK IN VRTALNIK ZA
FINOMEHANIKO
Prevod originalnega navodila za uporabo
JEMNÁ VRTACÍ BRUSKA
Překlad originálního provozního návodu
JEMNÁ VŔTACIA BRÚSKA
Preklad originálneho návodu na obsluhu
GB Translation of the original instructions Page 1
HU Az originál használati utasítás fordítása Oldal 19
SI Prevod originalnega navodila za uporabo Stran 37
CZ Překlad originálního provozního návodu Strana 55
SK Preklad originálneho návodu na obsluhu Strana 73
DE / AT / CH Originalbetriebsanleitung Seite 91
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of
the device.
Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik
funkcióját.
Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.
Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.
Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.
C
A
B
14b
PFBS 160 B2
GB1
Contents
Introduction ......................................................2
Intended use ................................................................ 2
Features ................................................................... 2
Package contents ............................................................ 2
Technical data .............................................................. 3
General Power Tool Safety Warnings ................................3
1. Work area safety .......................................................... 3
2. Electrical safety ........................................................... 4
3. Personal safety ............................................................ 4
4. Power tool use and care .................................................... 5
5. Service .................................................................. 5
Safety instructions for all applications ............................................ 5
Additional safety instructions for all applications .................................... 7
Supplementary safety instructions for grinding and abrasive cutting ..................... 8
Supplementary safety instructions for working with wire brushes. . . . . . . . . . . . . . . . . . . . . . . . 8
Safety instructions for LED lights ................................................. 9
General safety instructions for batteries and cells ................................... 9
Original accessories/auxiliary equipment ......................................... 9
Use ............................................................10
Changing/inserting the tool/collet chuck. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Whet stone ................................................................10
Fitting abrasive belts .........................................................10
Fitting polishing attachments ...................................................10
Switching on and off/setting speed range ........................................10
Using the grip ring with LED light ...............................................11
Notes on working with materials/tools/speed range ............................... 11
Flexible shaft ..............................................................13
Stand for the multi-tool .......................................................13
Router cage ...............................................................14
Changing the batteries .......................................................14
Cleaning, care and storage ........................................14
Kompernass Handels GmbH warranty ..............................15
Service .........................................................16
Importer .......................................................16
Disposal ........................................................16
Translation of the original Conformity Declaration .....................17
PFBS 160 B2
2 GB
PRECISION MULTI-GRINDER
PFBS 160 B2
Introduction
Congratulations on the purchase of your new appli-
ance. You have chosen a high-quality product. The
operating instructions are part of this product. They
contain important information about safety, usage
and disposal. Before using the product, please
familiarise yourself with all operating and safety
instructions. Use the product only as described and
for the range of applications specified. Please also
pass these operating instructions on to any future
owner.
Intended use
This precision drill grinder (hereafter also referred
to as the "appliance") is intended for drilling, mill-
ing, engraving, polishing, cleaning, grinding, cut-
ting of wood, metal, plastics, ceramics and stone
in dry rooms. Any other uses of or modifications
to the machine are deemed to be improper usage
and may result in serious physical injury. Not for
commercial use.
Features
Precision drill grinder:
ON/OFF switch
Power cable
Metal clip
Ventilation slits
Union nut
Tensioning nut
Collect chuck 3.2 mm (pre-assembled)
Grip ring with LED light
Spindle lock button
Carbon brushes
Infinitely variable speed control
Accessories (see fig. A):
Locking screw
Router cage
Flexible shaft
14b
Union nut (flexible shaft)
Collet chuck mount
Stand mount
Stand
Clamping device
Accessories set (42 pieces) (see fig. B):
6 cutting discs
2 grinding discs, abrasive
1 whet stone
3 polishing attachments
5 abrasive belts
1 abrasive belt mandrel
1 combination spanner
1 collet chuck 2.4 mm
1 metal brush
2 synthetic brushes
1 mandrel for cutting/grinding discs
1 drill bit
1 milling bit
1 mandrel for polishing attachments
2 engraving bits
5 grinding bits, abrasive
8 cutting discs
ON/OFF switch LED light
Package contents
1 precision multi-grinder PFBS 160 B2
1 plastic case
1 flexible shaft
1 stand
1 clamping device
1 router cage
1 grip ring with LED light
1 accessories set (42 pieces)
1 set of operating instructions
PFBS 160 B2
GB3
Technical data
Rated power
consumption: 160 W
Rated voltage: 230 V
~
, 50 Hz
(AC)
Rated speed: n 10,000–40,000 rpm
Drills
: max. Ø 3.2 mm
Discs: max. Ø 25 mm
Protection class: II / (double insulation)
Noise emission value:
Noise measurement value determined in accord-
ance with EN 60745. The rated noise level of the
power tool is typically as follows:
Sound pressure level: L
PA
= 80 dB(A)
Uncertainty K: K
PA
= 3 dB
Sound power level: L
WA
= 91 dB(A)
Uncertainty K: K
WA
= 3 dB
Wear hearing protection!
Vibration emission value:
Total vibration values (vector total of three direc-
tions) determined in accordance with EN 60745:
Vibration emission value: a
h
= 2.3 m/s
2
Uncertainty K = 1.5 m/s
2
NOTE
The vibration level specified in these instruc-
tions has been measured in accordance with
a standardised measuring procedure and
can be used for equipment comparisons. The
specified vibration emission value can also
be used to make an initial exposure estimate.
WARNING!
The vibration level will vary according to the
use of the power tool and may sometimes
be higher than the value specified in these
instructions. Regular use of the power tool in
this way may cause the user to underestimate
the vibration. Try to keep the vibration loads
as low as possible. Measures to reduce the
vibration load are, e.g. wearing gloves and
limiting the working time. Wherein all states
of operation must be included (e.g. times
when the power tool is switched off and times
where the power tool is switched on but run-
ning without load).
General Power Tool
Safety Warnings
WARNING!
Read all safety warnings and all instructions.
Failure to follow the warnings and instruc-
tions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future
reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1. Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of flam-
mable liquids, gases or dust. Power tools cre-
ate sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
PFBS 160 B2
4 GB
2. Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric
shock.
b) Avoid body contact with earthed or ground-
ed surfaces, such as pipes, radiators, ranges
and refrigerators. There is an increased risk of
electric shock if your body is earthed or ground-
ed.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entan-
gled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD re-
duces the risk of electric shock.
3. Personal safety
a) Stay alert, watch what you are doing and
use common sense when operating a power
tool. Do not use a power tool while you are
tired or under the influence of drugs, alcohol
or medication. A moment of inattention while
operating power tools may result in serious
personal injury.
b) Use personal protective equipment. Always
wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes, hard
hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energising
power tools that have the switch on invites ac-
cidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewel-
lery or long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use
of dust collection can reduce dust-related haz-
ards.
PFBS 160 B2
GB5
4. Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at
the rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that can-
not be controlled with the switch is dangerous
and must be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing ac-
cessories or storing power tools. Such preven-
tive safety measures reduce the risk of starting
the power tool accidentally.
d) Store idle power tools out of the reach of
children. Do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are dan-
gerous in the hands of untrained users.
e) Maintain power tools. Check for misalign-
ment or binding of moving parts, breakage of
parts and any other condition that may affect
the power tools operation. If damaged, have
the power tool repaired before use. Many ac-
cidents are caused by poorly maintained power
tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g) Use the power tool, accessories and tool
bits, etc. in accordance with these instruc-
tions, taking into account the working condi-
tions and the work to be performed. Use of
the power tool for operations different from
those intended could result in a hazardous
situation.
5. Service
a) Have your power tool serviced by a qualified
repair person using only identical replace-
ment parts. This will ensure that the safety of
the power tool is maintained.
WARNING!
Always wear safety googles
Safety instructions for all applica-
tions
General safety instructions for grinding, sand-
paper sanding, working with wire brushes,
polishing, milling and abrasive cutting:
a) This power tool is intended for use as a grind-
er, sandpaper sander, wire brush, polisher,
milling machine and abrasive cutting appli-
ance. Please follow all safety instructions,
instructions, diagrams and data that you re-
ceive with the appliance. If you do not observe
the following instructions, this can lead to an
electrical shock, fire and/or serious injuries.
b) Do not use any accessories that have not
been provided or recommended by the manu-
facturer for this power tool. Just because you
can attach the accessories to your power tool,
does not ensure they are safe to use.
c) The permissible speed of the accessory tool
used must be at least as high as the maximum
speed specified for the power tool. Acces-
sories that rotate faster than the permissible rate
can break and throw pieces into the air.
d) The external diameter and thickness of the
accessory tool used must comply with the di-
mensions of the power tool. Incorrectly dimen-
sioned accessory tools cannot be sufficiently
shielded or controlled.
PFBS 160 B2
6 GB
e) Grinding discs, sanding drums or other ac-
cessories must match the grinding spindle or
collet chuck of your power tool exactly. Ac-
cessory tools which do not fit precisely into the
take-up of the power tool will rotate unevenly,
vibrate severely and can lead to a loss of control.
f) Discs, grinding cylinders, cutting tools or
other accessories mounted on a mandrel must
be completely inserted in the collet or chuck.
Any "protrusion" or exposed parts of the
mandrel between the grinding tool and the
collet or chuck must be kept to a minimum.
If the mandrel is not sufficiently tightened or the
grinding tool protrudes too far, the tool could
come loose and been thrown out at high speed.
g) Never use damaged accessory tools. Before
each use, check accessory tools such as
grinding discs for chips or cracks, sanding
drums for cracks, wearing or excessive wear
and tear and wire brushes for loose or bro-
ken wires. If the power tool or the accessory
tool in use is dropped, check to see if it is
damaged or use an undamaged accessory
tool.
When you have checked and inserted the
accessory tool, ensure that you and any other
people in the vicinity remain outside of the
range of the rotating accessory tool and al-
low the tool to rotate at maximum speed for
one minute. Damaged accessory tools usually
break during this test period.
h) Wear personal protective equipment.
Depending on the application, ensure that
you use full face protection, eye protection
or goggles. If required, use a dust mask, ear
protectors, protective gloves or special apron
to protect you from grindings and material
particles. The eyes should be protected from
flying debris that may be caused during certain
applications. Dust or filter masks must be used
to filter any dust created by the application. If
you are exposed to loud noise for any length
of time, you may suffer hearing loss.
i) Ensure that other people remain at a safe dis-
tance to your workspace. Anyone who enters
the workspace must wear personal protective
equipment. Fragments of the workpiece or
broken accessory tools can fly off and cause
injury – even outside the immediate working
area.
j) Hold the power tool only by the insulated
gripping surfaces when performing an opera-
tion where the accessory tool may contact
hidden wiring or its own cord. Contact with
a live cable may also cause metal parts of the
appliance to become live and may result in an
electric shock.
k) Always hold the power tool firmly. When
running up to full speed, the torque of the motor
can cause the power tool to twist.
l) If possible, use clamps to hold the workpiece
in position. Never hold a small workpiece
in one hand and the power tool in the other
while you are using it. By clamping small
workpieces, you keep both hands free for better
control of the power tool. When cutting round
workpieces such as dowels, rods or pipes, be
aware that these can roll away and this can
cause the tool to jam and be thrown towards
you.
m) Hold the power cord away from any rotating
accessories. If you lose control of the appli-
ance, the cord may get cut or caught and your
hand or arm could get caught in the rotating
accessory tool.
n) Never put the power tool down until the ac-
cessory tool has come to a complete stand-
still. The rotating accessory tool could come
into contact with the surface and cause you to
lose control of the power tool.
PFBS 160 B2
GB7
o) When changing accessory tools or changing
settings, tighten the collet nut, the chuck or
other fixing elements tightly. Loose fixing ele-
ments can shift unexpectedly and lead to loss of
control; unfixed, rotating components will fly off
violently.
p) Do not leave the power tool running whilst
carrying it. Accidental contact between your
clothing and the rotating accessory tool could
lead to a physical injury.
q) Clean the ventilation slits of your power tool
regularly. The engine fan draws dust into the
housing and a strong accumulation of metal
dust can cause electrical hazards.
r) Do not use the power tool in the vicinity of
flammable materials. Sparks can ignite such
materials.
s) Do not use any accessory tools which require
liquid coolant. The use of water or other liquid
coolants may lead to an electric shock.
Additional safety instructions for all
applications
Kickback and corresponding safety instruc-
tions
Kickback is a sudden reaction caused when a
rotating accessory tool, e.g. grinding disc, abrasive
band, wire brush, etc., catches or jams. Catching
or jamming leads to an abrupt stop of the rotating
accessory tool. If this happens, an uncontrolled
power tool will turn rapidly against the direction
of rotation of the accessory tool.
If, for example, a grinding disc catches or jams,
the edge of the grinding disc that is projecting into
the workpiece can get caught and break off the
grinding disc or cause a kickback. The grinding
disc can then
fly in the direction of the operator or away from
him, depending on the direction of rotation of the
disc at the blockage. This can also break grinding
discs.
A kickback is caused by incorrect use or misuse
of the power tool. This can be avoided by taking
proper precautions as described below.
a) Hold the power tool firmly in both hands
and position your body and arms so they
can absorb the force of a kickback. By taking
adequate precautions, the operator can stay in
control of the kickback forces.
b) Take special care when working around
corners, sharp edges, etc. Avoid allowing the
accessory tool to bounce back from the work-
piece or jam in the workpiece. The rotating
accessory tool is more likely to jam in corners or
sharp edges or if it rebounds off them. This can
cause a loss of control or kickback.
e) Do not use toothed saw blades. Such acces-
sories often cause a kickback or loss of control
over the power tool.
d) Always move the accessory tool in the same
direction in the material in which the cutting
edge leaves the material (in other words, the
same direction in which the dust is thrown
out). Guiding the power tool in the wrong direc-
tion will cause the cutting edge of the accessory
tool to jump out of the workpiece which can
lead to the accessory tool being pulled in this
direction.
e) Always fix the workpiece when using rotary
files, cutting discs, high-speed milling tools or
hard-metal tools. Even a minimal tilting in the
groove can cause these tools to jam and lead
to a kickback. When the cutting disc jams, it
usually breaks. When a rotary file, high-speed
milling tool or hard-metal milling tool jams, the
accessory tool can jump out of the groove and
lead to loss of control of the power tool.
PFBS 160 B2
8 GB
Supplementary safety instructions
for grinding and abrasive cutting
Special safety instructions for grinding and
abrasive cutting
a) Use only the grinding accessories approved
for your power tool and only for the recom-
mended applications. Example: Never grind
with the side surface of a cutting disc. Cutting
discs are designed to remove material with the
edge of the disc. Any lateral application of
force on these grinding tools can lead to break-
age.
b) Use only undamaged mandrels of the correct
size and length and without undercut on the
shoulder for conical and straight pencil grind-
ers. Using an appropriate mandrel reduces the
risk of breakages.
c) Avoid cutting disc jams or excessive contact
pressure. Do not make any excessively deep
cuts. Overloading the cutting disc increases the
stress and likelihood of tilting or blocking and
thus the possibility of a setback or a breakage
of the grinding tool.
d) Avoid putting your hand in the area in front
of or behind the rotating cutting disc. When
you move the cutting disc away from your hand,
it is possible, in the event of a kickback, that the
power tool along with the rotating disc could be
thrown out directly towards you.
e) If the cutting disc jams or you stop working,
switch the tool off and hold it steady until the
disc has completely stopped turning. Never
attempt to pull a rotating cutting disc out of a
cut. This could lead to kickback. Identify and
remove the cause of the jam.
f) Do not switch the power tool back on as long
as it is in the workpiece. Allow the cutting disc
to reach its full speed before you carefully
continue the cut. Otherwise, the disc may jam,
jump out of the workpiece or cause kickback.
g) Support panels or large workpieces to re-
duce the risk of the cutting disc jamming and
causing a kickback. Large workpieces can
bend under their own weight. The workpiece
must be supported on both sides, namely in the
vicinity of the cut, and also at the edge.
h) Be particularly careful when making "pocket
cuts" into existing walls or other obscured
areas. The protruding cutting disc may cut gas
or water pipes, electrical wiring or other objects
that can cause a kickback.
Supplementary safety instructions
for working with wire brushes
Special safety instructions for working with
wire brushes:
a) Be aware that the brush can lose wire bristles
even during normal operation. Do not over-
stress the wires by applying excessive pres-
sure to the brush. The wire bristles can easily
penetrate light clothing and/or skin.
b) Allow the brush to run at working speed for
at least one minute before applying it to the
workpiece. Ensure that no one is standing in
front of or in line with the brush during this
time. Loose pieces of wire could fly off during
the run-in period.
c) Aim the rotating steel brush away from your-
self. When working with these brushes, small
particles and minute pieces of wire can fly off
at great speed and pierce skin.
PFBS 160 B2
GB9
Safety instructions for LED lights
CAUTION! THERE IS A RISK OF
INJURY TO THE EYES!
Never aim the light directly at people or
animals and never look directly into the light
beam of the LED light.
General safety instructions for
batteries and cells
Do not expose batteries or cells to heat or open
flames. Avoid storage in direct sunlight.
Cells or batteries must not be short-circuited.
Cells or batteries may not be stored danger-
ously in a box or draw where they can short-
circuit each other or be short-circuited by other
conductive materials.
Do not unpack a cell or battery until you plan
to use it.
Cells or batteries must not be exposed to
mechanical impacts.
If a cell is leaking, do not let the fluid come into
contact with skin or eyes. If there is contact,
wash the affected area with plenty of water and
seek medical assistance.
Do not use any other charger apart from the
one specifically designed for use with these
appliances.
Always observe the polarity markings – positive
(+) and negative (−) on the cells, batteries and
appliances. Ensure proper use.
Cells or batteries, that are not suitable for use
with the appliance may not be used.
Do not use combinations of batteries from differ-
ent manufacturers, capacities, sizes or designs.
Keep cells and batteries out of the reach of
children.
If a cell or battery is swallowed, seek medical
assistance immediately.
Always purchase the correct cell or battery for
an appliance.
Keep cells and batteries clean and dry.
If the terminals of the cells or batteries are con-
taminated, clean them with a dry, clean cloth.
Store the original instructions and information
about the products safely for future information
and reference purposes.
Cells and batteries may not be used in applica-
tions for which they are not designed.
Always remove batteries from appliances that
are not in use, if possible.
Do attempt to recharge non-rechargeable
batteries.
There is a risk of explosion!
Original accessories/auxiliary
equipment
Use only the accessories and additional equip-
ment that are specified in the operating instruc-
tions and are compatible with the appliance.
PFBS 160 B2
10 GB
Use
Changing/inserting the tool/collet
chuck
Press the spindle lock and hold it down.
Turn the tensioning nut
until the lock clicks
into place.
Undo the tensioning nut
from the thread
using the combination spanner .
Remove any tool which is inserted.
First push the intended tool through the tension-
ing nut
before inserting it into the appropri-
ate collet chuck
for the tool shaft.
Press the spindle lock
and hold it down.
Push the collet chuck
into the thread insert
and screw the tensioning nut tight with the
combination spanner .
Using an accessory tool with a mandrel:
Use the screwdriver side of the combination
spanner
to undo and tighten the screw on
the mandrel.
Insert the mandrel into the appliance as de-
scribed.
Use the combination spanner
to undo the
screw on the mandrel.
Insert the desired accessory tool between the
two washers on the screw.
Use the combination spanner
to tighten the
screw on the mandrel.
Whet stone
Do not manually grind any edges with the whet
stone
.
Fitting abrasive belts
Push the abrasive belt onto the abrasive belt
mandrel from above. Tighten the screw on
the abrasive belt mandrel in order to fix the
abrasive belt .
Fitting polishing attachments
Screw the polishing attachment onto the tip
of the mandrel for polishing attachments .
Switching on and off/setting speed
range
CAUTION!
The rotation direction can be read off the
arrow engraved on the union nut
(anti-
clockwise symbol).
Switching on/setting the speed range:
Set the ON/OFF switch
to the "I" position.
Set the infinitely variable speed control
to
a position between "1" and "MAX".
Switching off:
Move the ON/OFF switch
to the position
"O".
PFBS 160 B2
GB11
Using the grip ring with LED light
Hold down the spindle lock and screw the
tensioning nut
anticlockwise off the thread.
Release the spindle lock
.
Then screw the union nut
anticlockwise off
the thread.
Screw the grip ring with LED
clockwise onto
the screw thread.
Hold down the spindle lock
and screw the
tensioning nut clockwise onto the thread.
Release the spindle lock
.
Move the ON/OFF switch of the LED light
to the position "I" to switch it on (see fig. C).
Move the ON/OFF switch of the LED light
to the position "O" to switch it off again.
Proceed in reverse order to replace the union
nut
.
Notes on working with materials/
tools/speed range
Use the milling bits for working on wood, plas-
tics and plasterboard at maximum speed.
Determine the rotational speed range for work-
ing on zinc, zinc alloys, aluminium, copper and
lead by trying it out on test pieces.
Use a low rotational speed for work on plastics
and materials with a low melting point.
Use a high rotational speed for working on
wood.
Carry out cleaning, polishing and buffing work
in the medium speed range.
NOTE
The milling bit
is not suitable for steel or
iron. Suitable products are available in stores.
The following are recommendations only and not
binding. When carrying out practical work, carry
out your own tests to see which tool and which set-
tings are ideal for the material you are working on.
Set a suitable rotational speed:
Number on the speed
control
Material being
worked
1 Plastics and materials
with a low melting
point
2–3 Stone, ceramics
4 Soft wood, metal
5 Hardwood
Max. Steel
PFBS 160 B2
12 GB
Application examples/selecting a suitable tool:
Function Accessories Use Protrusion
(min–max) mm
Drilling
Drill bit
Working wood 18–25, using the small-
est drill, the protrusion is
10 mm
Milling
Milling bit
Various jobs; e.g. creat-
ing recesses, hollows,
forms, grooves or slits
18–25
Engraving
Engraving bits
Labelling, handicraft 18–25
Polishing, rust removal
CAUTION!
Exert only slight pressure
when applying the tool
to the workpiece.
Metal brush
Rust removal 9–15
Polishing attachments
Various metals and
plastics, especially
precious metals such as
gold and silver
12–18
Cleaning
Synthetic brushes
e.g. cleaning hard-to-
access plastic housings
or the area around a
door lock
9–15
Grinding
Grinding discs
Grinding work on
stone, wood, fine work
on hard materials such
as ceramics or alloyed
steel
12–18
Grinding bits
10
Abrasive belts
10
Disconnecting
Cutting discs
Working metal, plastic
and wood
12–18
PFBS 160 B2
GB13
Note that the maximum diameter of the grind-
ing assembly and of grinding cones, pencil
grinders and grinding points with a thread insert
may not exceed 55mm and the maximum
diameter for sandpaper sanding accessories
may not exceed 80mm.
NOTE
The max. permissible length of a mandrel is
33 mm.
Store the accessories in the original box or store
the accessory components somewhere else to
protect them from damage.
Store the accessories somewhere dry and not in
the vicinity of aggressive media.
If you exert too much pressure, the fitted tool
can break and/or the workpiece could be dam-
aged. You will achieve optimum working results
by moving the tool over the workpiece at a
steady speed and while exerting light pressure.
When carrying out cutting work, hold the appli-
ance firmly with both hands.
Observe the data and the information in the ta-
ble to prevent the end of the spindle from touch-
ing the perforated base of the grinding tool.
Flexible shaft
Never operate the spindle lock while the motor
is running. Otherwise, the appliance or the flex-
ible shaft may be damaged.
Screw the union nut anticlockwise off the
appliance and store it carefully.
Press the spindle lock
and hold it down.
Screw the tensioning nut
anticlockwise off
the appliance.
Fit the flexible shaft
onto the appliance. To
do this, the internal access of the flexible shaft
push the tensioning nut into the collet chuck
, .
First tighten the tensioning nut
and then the
union nut
14b
of the flexible shaft clockwise
onto the appliance with the combination span-
ner .
Place the desired accessory into the collet
chuck
, of the flexible shaft.
Push the black the collar back onto the flexible
shaft to lock the spindle.
Open the collet chuck mount
on the flexible
shaft with the combination spanner . Fit the
attachment and screw the collet chuck mount
back in place.
Stand for the multi-tool
Screw the stand into the clamping device .
NOTE
Depending on the desired attachment onto a
vertical or horizontal surface, you can screw
the stand
into the clamping device in two
different positions.
Screw the clamping device
onto the edge of
a work bench or table with a maximum thick-
ness of 55 mm.
The stand
is height-adjustable. Undo the
upper part of the stand by turning it anti-
clockwise (−). Pull out the tube to the maximum
height and lock it again by turning it clockwise
(+).
The mount
is also height-adjustable; turn
the black thread anticlockwise. After you have
set the mount to the correct height, tighten the
thread by turning in the opposite direction.
Fix the appliance with the metal clip
onto the
mount of the stand . The mount can be
turned 360°.
PFBS 160 B2
14 GB
Router cage
With this attachment, the appliance is particularly suit-
able for cutting special forms (holes for plugs, etc.).
Insert the milling bit
as described in the sec-
tion "Changing/inserting the tool/collet chuck".
Ensure that the shaft of the bit protrudes out of
the collet chuck by about 13 mm.
Screw the union nut
anticlockwise off the
appliance and store it carefully.
Unscrew the router cage
off the appliance.
To set the correct working height, undo the
locking screw
and adjust the foot of the
router cage to the desired size.
Afterwards, retighten the locking screw
.
Changing the batteries
Make sure that the LED light is turned off.
Remove the three screws from the rear of the
grip ring with LED
.
Replace the used batteries in the appliance
with new batteries of the same type (button
cell LR41). Note polarity when installing new
batteries.
Close the battery compartment again by re-
placing the three screws.
Cleaning, care and storage
WARNING! RISK OF INJURY!
Switch the appliance off and remove the
power plug before starting any work on
the appliance.
The appliance is maintenance-free.
Remove all dirt from the appliance. Use a dry
cloth to do this.
WARNING!
If the power cord requires replacement, this
should be carried out by the manufacturer or
an approved representative to avoid safety
hazards.
Store the appliance and all the individual piec-
es in the provided plastic case to ensure you do
not lose any part.
NOTE
Replacement parts not listed (such as the
rechargeable battery, battery charger) can
be ordered via our service hotline.
WARNING!
Always ensure that the power plug or
the mains cable is replaced only by the
manufacturer of the appliance or by an
approved customer service provider. This
will ensure that the safety of the appliance is
maintained.
ca. 13 mm
PFBS 160 B2
GB15
Kompernass Handels GmbH
warranty
Dear Customer,
This appliance has a 3-year warranty valid from
the date of purchase. If this product has any faults,
you, the buyer, have certain statutory rights. Your
statutory rights are not restricted in any way by the
warranty described below.
Warranty conditions
The validity period of the warranty starts from the
date of purchase. Please keep your original receipt
in a safe place. This document will be required as
proof of purchase.
If any material or production fault occurs within
three years of the date of purchase of the product,
we will either repair or replace the product for you
at our discretion. This warranty service is depend-
ent on you presenting the defective appliance and
the proof of purchase (receipt) and a short written
description of the fault and its time of occurrence.
If the defect is covered by the warranty, your product
will either be repaired or replaced by us. The repair
or replacement of a product does not signify the
beginning of a new warranty period.
Warranty period and statutory claims for
defects
The warranty period is not prolonged by repairs
effected under the warranty. This also applies to
replaced and repaired components. Any damage
and defects present at the time of purchase must
be reported immediately after unpacking. Repairs
carried out after expiry of the warranty period shall
be subject to a fee.
Scope of the warranty
This appliance has been manufactured in accordance
with strict quality guidelines and inspected meticu-
lously prior to delivery.
The warranty covers material faults or production
faults. The warranty does not extend to product parts
subject to normal wear and tear or fragile parts such
as switches, batteries, baking moulds or parts made
of glass.
The warranty does not apply if the product has been
damaged, improperly used or improperly maintained.
The directions in the operating instructions for the
product regarding proper use of the product are
to be strictly followed. Uses and actions that are
discouraged in the operating instructions or which
are warned against must be avoided.
This product is intended solely for private use and
not for commercial purposes. The warranty shall be
deemed void in cases of misuse or improper handling,
use of force and modifications/repairs which have
not been carried out by one of our authorised
Service centres.
Warranty claim procedure
To ensure quick processing of your case, please
observe the following instructions:
Please have the till receipt and the item number
(e.g. IAN 12345) available as proof of purchase.
You will find the item number on the type plate,
an engraving on the front page of the instructions
(bottom left), or as a sticker on the rear or bot-
tom of the appliance.
If functional or other defects occur, please
contact the service department listed either by
telephone or by e-mail.
You can return a defective product to us free of
charge to the service address that will be provided
to you. Ensure that you enclose the proof of
purchase (till receipt) and information about
what the defect is and when it occurred.
NOTE
For Parkside and Florabest tools, please send
us only the defective item without the acces-
sories (e.g. battery, storage case, assembly
tools, etc.).
You can download these instructions
along with many other manuals,
product videos and software on
www.lidl-service.com.
PFBS 160 B2
16 GB
Service
WARNING!
Have the power tool repaired by the service
centre or a qualified electrician and only
using genuine replacement parts. This will
ensure that the safety of the appliance is
maintained.
Always ensure that the power plug or the
mains cable is replaced only by the manu-
facturer of the appliance or by an approved
customer service provider. This will ensure
that the safety of the appliance is maintained.
Service Great Britain
Tel.: 0871 5000 720 (£ 0.10/Min.)
IAN 281406
Importer
Please note that the following address is not the
service address. Please use the service address
provided in the operating instructions.
KOMPERNASS HANDELS GMBH
BURGSTRASSE 21
44867 BOCHUM
GERMANY
www.kompernass.com
Disposal
The packaging is made from environmen-
tally friendly material and can be dis-
posed of at your local recycling plant.
Do not dispose of power tools in
your normal domestic waste!
European Directive 2012/19/EU requires that
worn-out power tools be collected separately and
recycled in an environmentally compatible manner.
Please consult your local authorities regarding
suitable disposal of worn out power tools/battery
packs.
Batteries should not be disposed of
with normal household waste.
Consumers are legally obliged to dispose of used
batteries at a collection point in their town/district
or at a retail store. This obligation is intended to
ensure that batteries are disposed of in an environ-
mentally responsible manner. Dispose of batteries
only when they are fully discharged.
PFBS 160 B2
GB17
Translation of the original Conformity Declaration
We, KOMPERNASS HANDELS GMBH, document officer: Mr. Semi Uguzlu, BURGSTR. 21,
44867 BOCHUM, GERMANY, hereby declare that this product complies with the following
standards, normative documents and EC directives:
Machinery Directive
(2006/42/EC)
EMC (Electromagnetic Compatibility)
(2014/30/EU)
RoHS Directive
(2011/65/EU)*
* The manufacturer bears the full responsibility for compliance with this conformity declaration. The object
of the declaration described above complies with the requirements of the Directive 2011/65/EU of the
European Parliament and Council of 8 June 2011 on the limitations of use of certain dangerous sub-
stances in electrical and electronic appliances.
Applied harmonised standards:
EN 60745-2-23:2013
EN 60745-1:2009+A11:2010
EN 55014-1:2006/+A1:2009/+A2:2011
EN 55014-2:1997/+A1:2001/+A2:2008
EN 61000-3-2:2014
EN 61000-3-3:2013
Type/appliance designation:
Precision multi-grinder PFBS 160 B2
Year of manufacture: 09 - 2016
Serial number: IAN 281406
Bochum, 07/12/2016
Semi Uguzlu
- Quality Manager -
We reserve the right to make technical changes in the context of further product development.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112

Parkside PFBS 160 B2 Translation Of The Original Instructions

Kategória
Elektrické náradie
Typ
Translation Of The Original Instructions

V iných jazykoch