Parkside PFBS 10.8 A1 Operation and Safety Notes

Typ
Operation and Safety Notes
IAN 270218
CORDLESS MULTI-GRINDER PFBS 10.8 A1
AKKU-FEINBOHRSCHLEIFER
Bedienungs- und Sicherheitshinweise
Originalbetriebsanleitung
CORDLESS MUL TI-GRINDER
Operation and Safety Notes
Translation of the original instructions
AKUMULATOR O WA SZLIFIERKO-WIERTARKA
Wskazówki dotyczące obsługi i bezpieczeństwa
Tłumaczenie oryginalnej instrukcji obsługi
AKUMULATORSKI BRUSILNIK
IN VRTALNIK ZA FINOMEHANIKO
Navodila za upravljanje in varnostna opozorila
Prevod originalnega navodila za uporabo
AKU JEMNÁ VRTACÍ BRUSKA
Pokyny pro obsluhu a bezpečnostní pokyny
Překlad originálního provozního návodu
AKUMULÁTOROVÁ VŔTACIA BRÚSKA
Pokyny pre obsluhu a bezpečnostné pokyny
Preklad originálneho návodu na obsluhu
AKKUS MULTICSISZOLÓ
Kezelési és biztonsági utalások
Az originál használati utasítás fordítása
GB Operation and Safety Notes Page 5
PL Wskazówki dotyczące obsługi i bezpieczeństwa Strona 19
HU Kezelési és biztonsági utalások Oldal 35
SI Navodila za upravljanje in varnostna opozorila Stran 49
CZ Pokyny pro obsluhu a bezpečnostní pokyny Strana 63
SK Pokyny pre obsluhu a bezpečnostné pokyny Strana 77
DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 91
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the
device.
Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi
funk cjami urządzenia.
Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik
funk cióját.
Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.
Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.
Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.
AKUMULATOROWA SZLIFIERKO-WIERTARKA
Wskazówki dotyczące obsługi i bezpieczeństwa
Tłumaczenie oryginalnej instrukcji obsługi
6
8
3
7
D
E
F
G H
18
4
1 2
5
A CB
16
14
15
19
22
20
21
12
23
13
18
17
9
11
11a
10
5 GB
Table of contents
Introduction
Proper use ............................................................................................................................................Page 6
Features and equipment .....................................................................................................................Page 6
Included items .....................................................................................................................................Page 6
Technical information .......................................................................................................................... Page 6
General safety advice for electrical power tools
1. Workplace safety ...........................................................................................................................Page 7
2. Electrical safety ............................................................................................................................... Page 7
3. Personal safety ................................................................................................................................Page 8
4. Careful handling and use of electrical power tools .....................................................................Page 8
5. Use and handling of the cordless electrical power tool ..............................................................Page 9
6. Service .............................................................................................................................................Page 9
Safety instructions for all operations .................................................................................................. Page 9
Further safety instructions for all operations ......................................................................................Page 11
Additional safety instructions for grinding and cutting-off operations .............................................Page 11
Special safety advice for working with wire brushes ........................................................................Page 12
Safety advice applicable specifically to cordless multi-grinders ......................................................Page 12
Safety notices for chargers ................................................................................................................. Page 13
Operation
Charging the battery pack .................................................................................................................Page 13
Inserting / removing the battery pack into / out of the drill / grinder ................................................Page 13
Reading off the battery status .............................................................................................................Page 13
Inserting or replacing a tool / collet ...................................................................................................Page 14
Switching on and off / Setting the speed range ................................................................................Page 14
Advice on working with materials / Tools / Speed ranges ...............................................................Page 14
Tips and tricks ...................................................................................................................................... Page 15
Maintenance and cleaning
Maintenance .......................................................................................................................................Page 15
Cleaning ..............................................................................................................................................Page 15
Service ...............................................................................................................................................Page 16
Warranty .........................................................................................................................................Page 16
Disposal ............................................................................................................................................Page 16
Translation of the original declaration of conformity /
Manufacturer ............................................................................................................................... Page 17
6 GB
Introduction
Introduction / General safety advice for electrical power tools
Cordless multi-grinder
PFBS 10.8 A1
Q
Introduction
We congratulate you on the purchase of your new
device. You have chosen a high quality product. The
instructions for use are part of the product. They
contain important information concerning safety,
use and disposal. Before using the product, please
familiarise yourself with all of the safety information
and instructions for use. Only use the unit as de
scribed
and for the specified applications. If you pass the
product on to anyone else, please ensure that you
also pass on all the documentation with it.
Q
Proper use
The rechargeable precision rotary tool with the cor-
responding accessory (as supplied) is intended to
be used for drilling, milling, engraving, polishing,
cleaning, grinding, cutting and sawing materials
such as wood, metal, plastic, ceramics or stone in
dry environments. Any other use or modification to
the drill / grinder shall be considered as improper
use and could give rise to considerable dangers.
The manufacturer will not accept liability for loss or
damage arising from improper use. Not intended
for commercial use.
Q
Features and equipment
Cordless multi-grinder:
1
Rotational speed control
2
Battery-operated LED
3
Battery pack release button
4
Battery pack
5
ON / OFF switch
6
Clamping nut
7
Spigot nut
8
Spindle lock
Battery charger (see Fig. A):
9
Charging cradle
10
Mains adapter
11
Charge indicator red
11 a
Charge indicator green
Accessories (see Fig. B):
12
6 HSS drills
13
2 Mandrels for mounting tools
14
3 Polishing wheels
15
4 Grinding wheels
16
1 Metal brush
17
16 Cutting wheels
18
5 Collets
19
2 Plastic brushes
20
3 Milling bits
21
2 Engraving bits
22
5 Grinding bits
23
Combination tool
Q
Included items
1 Cordless multi-grinder with rechargeable
battery pack
1 Charging cradle with mains adapter
1 Accessory kit (50-piece)
1 Operating instructions
Q
Technical information
Model PFBS 10.8 A1:
Rated voltage: 10.8 V
Rated speed: n 5000–25000 min
-1
Max. disc ø: 25 mm
Collet capacity
: max. ø 3.2 mm
Rechargeable battery pack PFBS 10.8 A1-1:
Rated voltage: 10.8 V
Capacity: 1300 mAh
Type: LITHIUM-ION
Battery charger PFBS 10.8 A1-2:
Primary (Input):
Rated voltage: 230–240 V∼, 50–60 Hz
Rated input: 9 W
Secondary (Output):
Rated voltage: 12.6 V
Charging current: 450 mA
7 GB
Introduction
Introduction / General safety advice for electrical power tools
Charging duration: approx. 3 hours
Protection class: II /
Noise and vibration data:
Measured values for noise are determined in accor-
dance with EN 60745. The A-weighted noise level
of the electrical power tool are typically:
Sound pressure level L
pA
: 66 dB(A)
Sound power level
L
WA
: 77 dB(A)
Uncertainty K: 3 dB
Wear ear protection!
Evaluated acceleration, typical:
Hand / arm vibration: 3.583 m / s
2
Uncertainty K = 1.5 m / s
2
Note: The vibration level specified in these instruc-
tions was measured in accordance with an EN 60745
standardised measurement process and can be used
to compare equipment. The vibration emission value
specified can also serve as a preliminary assessment
of the exposure.
The vibration level will change according to the ap-
plication of the electrical tool an in some cases may
exceed the value specified in these instructions. Re-
gularly using the electric tool in such a way may
make
it easy to underestimate the vibration.
Try to keep the vibration loads
as low as possible. Measures to reduce the vibration
load are, e.g. wearing gloves and limiting the work-
ing time. Wherein all states of operation must be in-
cluded (e.g. times when the power tool is switched
off and times where the power tool is switched on but
running without load).
Q
General safety advice for
electrical power tools
Read
all the safety advice
and instructions! Failure
to observe the safety advice and instructions may
result in electric shock, fire and / or serious injury.
Keep all the safety advice and instructions
in a safe place for future reference!
The term “electrical tool” used in the safety advice
refers to electrical tools powered by mains electricity
(by means of a mains lead) and electrical tools pow-
ered by rechargeable batteries (without a mains lead).
1. Workplace safety
a) K
eep your working area clean and wel
l
lit. Untidy or poorly lit working areas can lead
to accidents.
b) Do not work with the device in poten-
tially explosive environments in which
there are inflammable liquids, gases o
r
dusts. Electrical power tools create sparks,
which can ignite dusts or fumes.
c) Keep children and other people away
while you are operating the electrical
tool. Distractions can cause you to lose con-
trol of the device.
2. Electrical safety
a) The mains plug on the power tool (or
on the power supply) must fit the
mains
socket. Never modify the plug in any
way. Never use adapter plugs with
earthed power tools. Unmodified plugs
and the correct sockets reduce the risk of elec-
tric shock.
b) Avoid touching earthed surfaces such
as pipes, radiators, ovens and refrig-
erators with any part of your body.
There is an increased risk of electric shock if
your body is earthed.
c) Keep the device away from rain or
moisture. Water entering an electrical device
increases the risk of electric shock.
d) Do not use the mains lead for any pur-
pose for which it was not intended, e.
g.
to carry the device, to hang up the de-
vice or to pull the mains plug out of
the mains socket. Keep the mains lead
away from heat, oil, sharp edges or
8 GB
General safety advice for electrical power tools
General safety advice for electrical power tools
moving parts of the device. Damaged or
tangled mains leads increase the risk of elec-
tric shock.
e) When working outdoors with an elec-
trical power tool always use extension
cables that are also approved for use
outdoors. The use of an extension cable suit-
able for outdoor use reduces the risk of elec-
tric shock.
f) Use a residual current device (RCD) for
protection if operating the electrical
power tool in a moist environment is
unavoidable. The use of an RCD reduces
the risk of electric shock.
3. Personal safety
a) Remain alert at all times, watch what
you are doing and always proceed
with caution. Do not use the device if
you are tired or under the influence of
drugs, alcohol or medication. One mo
ment
of carelessness when using the device can lead
to serious injury.
b)
Wear personal protective
equipment and always wear
safety glasses. The wearing of
personal protective equipment such as dust
masks, non-slip safety shoes, safety helmets or
ear protectors, appropriate to the type of elec-
trical power tool used and work undertaken,
reduces the risk of injury.
c) Avoid accidental starting. Verify the po-
wer tool is switched off before connec-
ting it to the mains and / or connecting
the battery, picking it up, or carrying it.
Accidents can happen if you carry the device
with your finger on the ON / OFF switch or with
the device switched on.
d) Remove any setting tools or spanners
before you switch the device on. A tool
or spanner left attached to a rotating part of a
device can lead to injury.
e) Avoid placing your body in an unnat-
ural position. Keep proper footing and
balance at all times. By doing this you will
be in a better position to control the device in
unforeseen circumstances.
f) Wear suitable clothing. Do not wear
loose clothing or jewellery. Keep your
hair, clothing and gloves clear of mov-
ing parts. Loose clothing, jewellery or long
hair can become trapped in moving parts.
g) If vacuum dust extraction and collection
devices are fitted do not forget to
check
that they are properly connected and
correctly used. The use of these devices
reduces the hazard presented by dust.
4. Careful handling and use
of electrical power tools
a) Do not overload the device. Always
use an electrical power tool that is
intended for the task you are under-
taking. By using the right electrical power
tool for the job you will work more safely and
achieve a better result.
b) Do not use an electrical power tool if
its switch is defective. An electrical power
tool that can no longer be switched on and off
is dangerous and must be repaired.
c) Pull the mains plug out of the socket
and / or remove the rechargeable bat-
tery before you make any adjustments
to the device, change accessories or
when the device is put away. This pre-
caution is intended to prevent the device from
unintentionally starting.
d) When not in use always ensure that
electrical power tools are kept out of
reach of children. Do not let anyone
use
the device if he or she is not familiar with
it or has not read the instructions and
advice. Electrical power tools are dangerous
when they are used by inexperienced people.
e) Look after the device carefully. Check
that moving parts are working prop-
erly and move freely. Check for any
parts that are broken or damaged
enough to detrimentally affect the
functioning of the device. Have dam-
9 GB
General safety advice for electrical power tools
General safety advice for electrical power tools
aged parts repaired before you use
the device. Many accidents have their origins
in poorly maintained electrical power tools.
f) Keep cutting tools clean and sharp.
Carefully maintained cutting tools with sharp
cutting edges are less likely to jam and are
easier to control.
g) Use the electrical power tool, accesso-
ries, inserted tools etc. in accordance
with these instructions and advice, and
the stipulations drawn up for this par-
ticular type of device. In doing this, take
into account the working conditions
and the task in hand. The use of electrical
power tools for purposes other than those in-
tended can lead to dangerous situations.
5. Use and handling of the cord-
less electrical power tool
a) Charge a rechargeable battery unit
using only the charger recommended
by the manufacturer. Chargers are often
designed for a particular type of rechargeable
battery unit. There is the danger of fire if other
types of rechargeable battery units are used.
b) Only the rechargeable battery units
supplied are to be used with an elec-
trical power tool. The use of other recharge-
able battery units may lead to the danger of
injury or fire.
c) When they are not being used, store
rechargeable battery units away from
paperclips, coins, keys. nails, screws
or other small metal objects that could
cause the contacts to be bridged. Short-
circuiting the contacts of a rechargeable battery
unit may result in heat damage or fire.
d) Fluids may leak out of rechargeable
battery units if they are misused. If this
happens, avoid contact with the fluid.
If contact occurs, flush the affected area
with water. Seek additional medical
help if any of the fluid gets into your
eyes. Escaping battery fluid may cause skin
irritation or burns.
CAUTION! DANGER OF EXPLOSION!
The batteries must never be recharged!
Protect the battery against
heat, e.g., against continuous
intense sunlight, fire, water
and moisture. Danger of explos
ion.
6. Service
a) Have your device repaired at the ser-
vice centre or by qualified specialist
personnel using original manufacturer
parts only. This will ensure that your device
remains safe to use.
Safety instructions for all
operations
Safety warnings common for grinding,
sanding, wire brushing, polishing, carving
or abrasive cutting-off operations:
a) This power tool is intended to function
as a grinder, sander, wire brush, pol-
isher, carving or cut-off tool. Read all
safety warnings, instructions, illustra-
tions and specifications provided with
this power tool. Failure to follow all instruc-
tions listed below may result in electric shock,
fire and / or serious injury.
b) Do not use accessories which are not
specifically designed and recommend-
ed by the tool manufacturer. Just because
the accessory can be attached to your power
tool, it does not assure safe operation.
c) The rated speed of the grinding acces-
sories must be at least equal to the
max-
imum speed marked on the power
tool.
Grinding accessories running faster than their
rated speed can break and fly apart.
d) The outside diameter and the thickness
of your accessory must be within the
capacity rating of your power tool. In-
10 GB
General safety advice for electrical power tools
General safety advice for electrical power tools
correctly sized accessories cannot be ade
quately
controlled.
e) The arbour size of wheels, sanding
drums or any other accessory must
properly fit the spindle or collet of the
power tool. Accessories that do not match
the mounting hardware of the power tool will
run out of balance, vibrate excessively and may
cause loss of control.
f) Mandrel mounted wheels, sanding
drums, cutters or other accessories
must be fully inserted into the collet
or chuck. If the mandrel is insufficiently held
and / or the overhang of the wheel is too long,
the mounted wheel may become loose and be
ejected at high velocity.
g) Do not use a damaged accessory. Be-
fore each use inspect the accessory
such
as abrasive wheels for chips and cra
cks,
sanding drum for cracks, tear or excess
wear, wire brush for loose or cracked
wires. If power tool or accessory is
dropped, inspect for damage or install
an undamaged accessory. After in
spect-
ing and installing an accessory, position
yourself and bystanders away from
the plane of the rotating accessory
and
run the power tool at maximum no-
load
speed for one minute. Damaged accesso-
ries will normally break apart during this test time.
h) Wear personal protective equipment.
Depending on application, use face
shield, safety goggles or safety glass-
es. As appropriate, wear dust mask,
hearing protectors, gloves and work-
shop apron capable of stopping small
abrasive or workpiece fragments. The
eye protection must be capable of stopping
flying debris generated by various operations.
The dust mask or respirator must be capable of
filtrating particles generated by your operation.
Prolonged exposure to high intensity noise may
cause hearing loss.
i) Keep bystanders a safe distance away
from work area. Anyone entering the
work area must wear personal protec-
tive equipment. Fragments of workpiece or
of a broken accessory may fly away and cause
injury beyond immediate area of operation.
j) Hold power tool by insulated gripping
surfaces only, when performing an op-
eration where the cutting accessory
may contact hidden wiring or its own
cord. Cutting accessory contacting a «live» wire
may make exposed metal parts of the power
tool «live» and could give the operator an elec-
tric shock.
k) Always hold the tool firmly in your
hand(s) during the start-up. The reaction
torque of the motor, as it accelerates to full
speed,
can cause the tool to twist.
l) U
se clamps to support workpiece wh
en-
ever practical. Never hold a small
work-
piece in one hand and the tool in the
other hand while in use. Clamping a small
workpiece allows you to use your hand(s) to
control the tool. Round material such as dowel
rods, pipes or tubing have a tendency to roll
while being cut, and may cause the bit to bind
or jump toward you.
m) Position the cord clear of the spinning
accessory. If you lose control, the cord may
be cut or snagged and your hand or arm may
be pulled into the spinning accessory.
n) Never lay the power tool down until
the accessory has come to a complete
stop. The spinning accessory may grab the
surface and pull the power tool out of your
control.
o) After changing the bits or making any
adjustments, make sure the collet nut,
chuck or any other adjustment devices
are securely tightened. Loose adjustment
devices can unexpectedly shift, causing loss of
control, loose rotating components will be vio-
lently thrown.
p) Do not run the power tool while car-
rying it at your side. Accidental contact
with the spinning accessory could snag your
clothing, pulling the accessory into your body.
q) Regularly clean the power tool’s air
vents. The motor’s fan will draw the dust inside
the housing and excessive accumulation of pow-
dered metal may cause electrical hazards.
11 GB
General safety advice for electrical power tools
General safety advice for electrical power tools
r) Do not operate the power tool near
flammable materials. Sparks could ignite
these materials.
s) Do not use accessories that require
liquid coolants. Using water or other liquid
coolants may result in electrocution or shock.
Further safety instructions
for all operations
Kickback and related warnings
Kickback is a sudden reaction to a pinched or sn
agged
rotating wheel, sanding band, brush or any other
accessory. Pinching or snagging causes rapid stalling
of the rotating accessory which in turn causes the
uncontrolled power tool to be forced in the direction
opposite of the accessory’s rotation.
For example, if an abrasive wheel is snagged or
pinched by the workpiece, the edge of the wheel
that is entering into the pinch point can dig into the
surface of the material causing the wheel to climb
out or kick out. The wheel may either jump toward or
away from the operator, depending on direction of
the wheel’s movement at the point of pinching. Abra-
sive wheels may also break under these conditions.
Kickback is the result of power tool misuse and / or
incorrect operating procedures or conditions and
can be avoided by taking proper precautions as
given below.
a) Maintain a firm grip on the power tool
and position your body and arm to al-
low you to resist kickback forces. The
operator can control kickback forces, if proper
precautions are taken.
b) U
se special care when working corne
rs,
sharp edges etc. Avoid bouncing and
snagging the accessory. Corners, sharp
edges or bouncing have a tendency to snag the
rotating accessory and cause loss of control or
kickback.
c)
Do not attach a toothed saw blade. S
uch
blades create frequent kickback and loss of
control.
d) Always feed the bit into the material
in the same direction as the cutting
edge is exiting from the material
(which
is the same direction as the chips are
thrown). Feeding the tool in the wrong direc-
tion causes the cutting edge of the bit to climb
out of the work and pull the tool in the direction
of this feed.
e) When using rotary files, cut-off wheels,
high-speed cutters or tungsten carbide
cutters, always have the work securely
clamped. These wheels will grab if they be-
come slightly canted in the groove, and can
kickback. When a cut-off wheel grabs, the
wheel itself usually breaks. When a rotary file,
high-speed cutter or tungsten carbide cutter
grabs, it may jump from the groove and you
could lose control of the tool.
Additional safety instructions
for grinding and cutting-off
operations
Safety warnings specific for grinding and
abrasive cutting-off operations:
a) Use only wheel types that are recom-
mended for your power tool and only
for recommended applications.
For example: do not grind with the
side of a cut-off wheel. Abrasive cut-off
wheels are intended for peripheral grinding,
side forces applied to these wheels may cause
them to shatter.
b) For threaded abrasive cones and plugs
use only undamaged wheel mandrels
with an unrelieved shoulder flange that
are of correct size and length. Proper
man-
drels will reduce the possibility of breakage.
c) Do not “jam” a cut-off wheel or apply
excessive pressure. Do not attempt to
make an excessive depth of cut. Over-
stressing the wheel increases the loading and
susceptibility to twisting or snagging of the wheel
in the cut and the possibility of kickback or w
heel
breakage.
d) Do not position your hand in line with
and behind the rotating wheel. When
12 GB
General safety advice for electrical power tools / Operation
General safety advice for electrical power tools
the wheel, at the point of operation, is moving
away from your hand, the possible kickback m
ay
propel the spinning wheel and the power tool
directly at you.
e) When wheel is pinched, snagged or
when interrupting a cut for any reason,
switch off the power tool and hold the
power tool motionless until the wheel
comes to a complete stop. Never att
empt
to remove the cut-off wheel from the
cut while the wheel is in motion other-
wise kickback may occur. Investigate and
take corrective action to eliminate the cause of
wheel pinching or snagging.
f) Do not restart the cutting operation in
the workpiece. Let the wheel reach full
speed and carefully re-enter the cut.
The wheel may bind, walk up or kickback if
the power tool is restarted in the workpiece.
g) Support panels or any oversized work-
piece to minimize the risk of wheel
pinching and kickback. Large workpieces
tend to sag under their own weight. Supports
must be placed under the workpiece near the
line of cut and near the edge of the workpiece
on both sides of the wheel.
h) Use extra caution when making a
“pocket cut” into existing walls or
other blind areas. The protruding wheel
may cut gas or water pipes, electrical wiring
or objects that can cause kickback.
Special safety advice for
working with wire brushes
a) Bear in mind that wire brushes lose
pieces of wire during normal use. Do
not overload the wires by applying too
much pressure. Flying pieces of wire can very
easily penetrate thin clothing and / or skin.
b)
Allow brushes to run at operating spe
ed
for at least one minute before using
them. During this time no one is to
stand
in front or in line with the brush. Loose
bristles or wires will be discharged during the
run-in time.
c) D
irect the discharge of the spinning wir
e
brush away from you. Small particles and
tiny wire fragments may be discharged at high
velocity during the use of these brushes and
may become imbedded in your skin.
Q
Safety advice applicable specif-
ically to cordless multi-grinders
When you use the drill / grinder wear the fol-
lowing protective equipment: safety glasses
and protective gloves.
CAUTION! RISK OF INJURY! The tool
continues to rotate after it has been switched
off! Avoid contact with rapidly rotating drill /
grinder components.
Securely support the work-
piece. Use clamps or a vice to grip the workpiece
firmly. This is much safer than holding it in your
hand.
RISK OF INJURY! Never
support yourself by placing your hands near or
in front of the device or the workpiece surface.
A slip can result in injury.
DANGER OF FIRE FROM FLYING
SPARKS!
Abrading metal creates flying sparks. For this
reason, always make sure that nobody is placed
in any danger and that there are no inflamma
ble
materials near the working area.
DUST HAZARD! Any
harmful / noxious dusts generated from machin-
ing represent a risk to the health of the person oper-
ating the device and to anyone near the work area.
Wear a dust mask!
NOXIOUS FUMES!
Ensure that there is adequate ventilation when
machining surfaces containing plastic or covered
with paint, varnish etc.
Its use as a saw or the use of saw blades with
this device is prohibited.
Do not soak the materials or the surface you are
about to work on with liquids containing solvents.
13 GB
General safety advice for electrical power tools / Operation
General safety advice for electrical power tools
Avoid abrading paints containing lead or other
substances hazardous to health.
Do not machine materials containing asbestos.
Asbestos is a known carcinogen.
Avoid contact with moving sanding or grinding
tools.
Do not machine moist materials or damp surfac
es.
NOTE! Do not allow the tool to come to a stand-
still by overloading it!
RISK OF INJURY! Switch
the device off and allow it to come to a standstill
before you put it down.
Always keep the device cle
an,
dry and free of oil or grease.
Safety notices for chargers
This appliance can be used by children aged
from
8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge if they have been giv-
en supervision or instruction concerning use of the
appliance in a safe way and understand the
hazards involved. Children shall not play with
the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
The charger is only suitable for
indoor use.
If the mains power cable of this appliance is
damaged, it has to be replaced by the manu-
facturer or its service department or a similarly
qualified person in order to avoid hazards.
Q
Operation
Never use the device for a purpose for which it was
not intended or with non-original parts / accessories.
The use of tools or accessories other than those rec-
ommended in the operating instructions could lead
to you suffering an injury.
Q
Charging the battery pack
NOTE! A battery pack that has been unused for a
while or never been charged must be charged before
reuse or first use. The battery pack requires about
3–5 cycles before it can reach its full charge. The
charging process takes about 180 minutes.
CAUTION! RISK OF INJURY!
Always pull
out the mains plug (
mains adapter
10
) before
you
insert the battery pack into or take it out of
the charger.
Insert the battery pack
4
into the charging
cradle
9
. This can only be inserted with the
correct polarity.
Connect the adapter
10
to a mains socket.
The red charge level indicator
11
will light up as
long as the battery pack is being charged. Once
charging is completed the red charge level in-
dicator
11
will extinguish and the green charge
level indicator
11 a
will light up. The battery
pack
4
is ready for use.
CAUTION! Do not charge a battery pack for
a second time in close succession. There is a
danger of overcharging the battery pack.
Q
Inserting / removing the
battery pack into / out of
the drill / grinder
Inserting the battery pack:
Set the ON / OFF switch
5
to position “0”.
Insert the battery pack
4
into the drill / grinder
until it engages.
Removing the battery pack:
Pressing the battery pack buttons
3
at the
sides at the same time allows you to remove
the battery pack
4
.
Q
Reading off the battery status
The status or residual power is indicated as follows
in the battery-operated LED
2
whenever the appli-
ance is switched on:
RED / ORANGE / GREEN = maximum charge / power
14 GB
Operation / Maintenance and cleaning
Operation
RED / ORANGE = medium-level charge / power
RED = weak charge recharge battery
Q
Inserting or replacing
a tool / collet
Press the spindle lock
8
and keep it pressed.
Rotate the clamping nut
6
until the lock engages.
Loosen the clamping nut
6
with the combina-
tion key
23
.
If a tool is already inserted, remove it.
First insert the tool you wish to use through the
clamping nut
6
before you insert it into the
collet
18
suitable for the tool shaft.
Press the spindle lock
8
and keep it pressed.
Insert the collet
18
into the threaded insert and
tighten the clamping nut
6
on the thread using
the combination key
23
.
NOTE: Use the screwdriver end of the combi-
nation key
23
to release or tighten the screw of
the mandrels
13
.
Q
Switching on and off / Setting
the speed range
Switching on / Setting the speed range:
Set the ON / OFF switch
5
to position “I”.
Set the rotational speed control
1
to a position
between „1“ and „MAX.“.
Switching off:
Set the ON / OFF switch
5
to position “0”.
Q
Advice on working with
materials / Tools / Speed ranges
Use the highest speed when working on steel
or iron with the milling bits.
Use a short trial on a test piece to determine the
optimum rotational speed range for working on
zinc, zinc alloy, aluminium, copper and lead.
Use the low speed range for working on plastics
and low-melting point materials.
Use high speeds on wood.
Use the medium speed range for cleaning,
polishing and buffing.
The following information shall be considered as
recommendatory only. Learn by practical experience
which tools and settings are the best for the materi-
als you work with.
Setting the appropriate speed
Symbols
Rotational
speed
control
1
Material
1–3
Plastics and low melting
point materials
6–7
Hardwood
4–5
Stone, Ceramics
Max
Steel
5
Softwood, metal
Examples of appropriate tool selection Function:
Function Accessory Application Projection
(min–max) mm
Drilling
HSS drill
12
Drilling wood 18–25 when us-
ing the smallest
drill the projection
is 10 mm
15 GB
Function Accessory Application Projection
(min–max) mm
Milling Milling bits
20
Various tasks, e.g. hollowing out, gouging,
shaping, grooving or slotting
18–25
Engraving Engraving
bits
21
Making marks, craft projects
(see Fig. D)
18–25
Polishing, derusting
CAUTION!
Use only the lightest
contact pressure of
the tool on the work-
piece.
Metal brush
16
Derusting
9–15
Polishing
wheel
14
Working on various metals and plastics, in
particular noble metals like gold or silver
(see Fig. F)
12–18
Cleaning Plastic brush
19
E.g. cleaning complex plastic housings or
the area around a door lock
9–15
Grinding Grinding
wheels
15
Grinding work on stone, wood; fine work
on hard mate
rials such as ceram
ic or alloyed
steel (see Fig. G)
12–18
Grinding bits
22
10
Cutting and sawing Cutting
discs
17
Cutting metal, plastic or wood
12–18
Operation / Maintenance and cleaning
Operation
Be sure not to exceed the maximum diameter of
composite abrasive wheels and grinding cones
and cylinders with 55 mm thread insert, and
the 80 mm maximum diameter of sandpaper
grinding accessories.
Note: The max. permissible mandrel length is
33 mm.
Store accessories inside the original box or oth-
erwise protect the accessories from damage.
Store accessories dry and away from aggres-
sive media.
Tips and tricks
Applying excessive pressure can cause the in-
stalled tool to break and / or damage the work
piece. Optimal results can be achieved by ap-
plying the tool to the work piece at a steady
speed range and little pressure.
Hold the device with both hands whilst cutting.
Please note the data and information in the
chart to prevent the spindle end touching the
perforated plate of the grinding tool.
Q
Maintenance and cleaning
Q
Maintenance
Before and after a prolonged period of non-use
fully charge the battery pack
4
.
When storing a lithium-ion battery for extended
periods, regularly check the charge. The optimal
charge is between 50 % and 80 %. The optimal
storage climate is cooling and dry.
Q
Cleaning
Clean all the dirt off the drill / grinder. Use a dry
cloth for cleaning.
16 GB
Translation of the original declaration of conformity / Manufacturer
Service / Warranty / Disposal
Q
Service
Have your device
repaired at the service centre or by
qualified specialist personnel using
original manufacturer parts only. This
will ensure that your device remains safe to use.
If the plug or lead
needs to be replaced, always have
the replacement carried out by the
manufacturer or its service centre. This
will ensure that your device remains safe to use.
Note: Spare parts not listed (e.g. carbon brushes,
switches) can be ordered through our call centre.
Q
Warranty
The warranty for this appliance is for 3
years from the date of purchase. The ap-
pliance has been manufactured with care
and meticulously examined before deliv-
ery. Please retain your receipt as proof
of purchase. In the event of a warranty
claim, please make contact by telephone
with our Service Department. Only in this
way can a post-free despatch for your
goods be assured.
The warranty covers only claims for material and
maufacturing defects, but not for transport damage,
for wearing parts or for damage to fragile compo-
nents, e.g. buttons or batteries. This product is for pri-
vate use only and is not intended for commercial use.
The warranty is void in the case of abusive and im-
proper handling, use of force and internal tampering
not carried out by our authorized service branch. Your
statutory rights are not restricted in any way by this
warranty.
The warranty period will not be extended by repairs
made unter warranty. This applies also to replaced
and repaired parts. Any damage and defects extant
on purchase must be reported immediately after
unpacking the appliance, at the latest, two days after
the purchase date. Repairs made after the expiration
of the warranty period are subject to payment.
GB
Service Great Britain
Tel.: 0871 5000 720
(0.10 / minute)
IAN 270218
Q
Disposal
The packaging is wholly composed of
environmentally-friendly materials that can
be disposed of at a local recycling centre.
Do not dispose of electrical
appliances with your domestic
waste!
According to the European Directive 2012 / 19 / EU,
concerning used electrical and electronic appliances
and its implementation in national law, superannu-
ated electrical appliances must be collected and
disposed of via an environmentally suitable recy-
cling facility.
Li-Ion
Do not dispose of rechargeable
batteries with your household
refuse!
Defective or worn out rechargeable batteries must
be recycled according to Directive 2006 / 66 / EC.
Dispose of batteries and appliances over the existing
collection facilities.
Your local communal or municipal authorities can
provide information on how to dispose of the worn
out appliance.
17 GB
Translation of the original
declaration of conformity /
Manufacturer
We, KOMPERNASS HANDELS GMBH, the person
responsible for documents: Mr Semi Uguzlu, BURG-
STRASSE 21, 44867 BOCHUM, GERMANY, hereby
declare that this product complies with the following
standards, normative documents and EU directives:
Machinery Directive (2006 / 42 / EC)
EU Low Voltage Directive (2006 / 95 / EC)
Electromagnetic Compatibility
(2004 / 108 / EC)
RoHS Directive (2011 / 65 / EU)
Applicable harmonized standards
EN 55014-1:2006+A1+A2
EN 55014-2:1997+A1+A2
EN 60335-1:2012
EN 60335-2-29:2004+A2:10
EN 60745-1:2009+A11
EN 60745-2-23:2013
EN 61000-3-2:2006/+A1:2009/+A2:2009
EN 61000-3-3:2013
EN 62233:2008
Type / Appliance Designation:
Cordless multi-grinder PFBS 10.8 A1
Date of manufacture (DOM): 08–2015
Serial number: IAN 270218
Bochum, 31.08.2015
Semi Uguzlu
- Quality Manager -
We reserve the right to make technical modificat
ions
in the course of further development.
Translation of the original declaration of conformity / Manufacturer
Service / Warranty / Disposal
18
Spis zawartości
19 PL
Spis zawartości
Wstęp
Użytkowanie zgodne z przeznaczeniem .......................................................................................Strona 20
Wyposażenie ...................................................................................................................................Strona 20
Zakres dostawy ................................................................................................................................Strona 20
Dane techniczne ..............................................................................................................................Strona 20
Ogólne wskazówki bezpieczeństwa dla elektronarzędzi
1. Bezpieczeństwo miejsca pracy ..................................................................................................Strona 21
2. Bezpieczeństwo elektryczne .......................................................................................................Strona 21
3. Bezpieczeństwo osób .................................................................................................................Strona 22
4. Staranne obchodzenie się i użytkowanie narzędzi elektrycznych ..........................................Strona 23
5. Używanie i obchodzenie się z narzędziem akumulatorowym .................................................Strona 23
6. Serwis ...........................................................................................................................................Strona 24
Wskazówki bezpieczeństwa dla wszystkich zastosowań ............................................................Strona 24
Inne wskazówki bezpieczeństwa dla wszystkich zastosowań .....................................................Strona 26
Dodatkowe wskazówki dotyczące bezpieczeństwa podczas szlifowania iprzecinania .......... Strona 26
Szczególne wskazówki dotyczące bezpieczeństwa podczas pracy przy użyciu
szczotek drucianych ........................................................................................................................Strona 27
Wskazówki dotyczące bezpieczeństwa podczas używania dla wiertarko-szlifierek.................Strona 27
Wskazówki dotyczące bezpieczeństwa ładowarek .....................................................................Strona 28
Obsługa
Ładowanie akumulatora Pack .........................................................................................................Strona 28
Założenie / usunięcie akumulatora Pack z urządzenia .................................................................Strona 29
Odczyt stanu akumulatora ..............................................................................................................Strona 29
Narzędzie / tulejka zaciskowa - założenie / wymiana .................................................................Strona 29
Załączenie i wyłączenie / ustawienie zakresu obrotu ...................................................................Strona 29
Wskazόwki dotyczące obrόbki materiału / narzędzi / zakresu obrotu .......................................Strona 29
Pomocne wskazówki........................................................................................................................Strona 31
Konserwacja oraz czyszczenie
Konserwacja .....................................................................................................................................Strona 31
Czyszczenie .....................................................................................................................................Strona 31
Serwis .............................................................................................................................................Strona 31
Gwarancja ..................................................................................................................................Strona 32
Usuwanie ..................................................................................................................................... Strona 32
Tłumaczenie oryginału Deklaracji zgodności WE / Producent ........Strona 33
20 PL
Wstęp / Ogólne wskazówki bezpieczeństwa dla elektronarzędzi
Wstęp
Akumulatorowa szlifierko-
wiertarka PFBS 10.8 A1
Q
Wstęp
Gratulujemy zakupu nowego urządzenia. Tym sa-
mym zdecydowali się Państwo na zakup produktu
wysokiej jakości. Instrukcja obsługi jest częścią tego
produktu. Zawiera ona ważne wskazówki dotyczące
bezpieczeństwa, użytkowania iutylizacji. Przed
pierwszym użyciem produktu należy zapoznać się
ze wszystkimi wskazówkami dotyczącymi obsługi
ibezpieczeństwa. Używać produktu wyłącznie
zgodnie zjego poniżej opisanym przeznaczeniem.
Wprzypadku przekazania produktu innej osobie
należy dołączyć do niego całą jego dokumentację.
Q
Użytkowanie zgodne
z przeznaczeniem
Akumulatorowa szlifierko-wiertarka należy używać z
odpowiednimi akcesoriami (takimi, jak dostarczone)
do borowania, frezowania, grawerowania, polero-
wania, czyszczenia, szlifowania, oddzielania od
materiałów takich, jak drewno, metal, tworzywo
sztuczne, ceramika czy kamień w suchych pomiesz-
czeniach. Każde inne zastosowanie lub dokonywa-
nie zmian na urządzeniu uważane jest za sprzeczne
z przeznaczeniem i niesie ze sobą znaczne ryzyko
zagrożenia wypadkiem. Za szkody powstałe na
wskutek zastosowania sprzecznego z przeznacze-
niem, producent nie przejmuje żadnej odpowiedzial-
ności. Nie do użytku komercyjnego.
Q
Wyposażenie
Akumulatorowa szlifierko-wiertarka:
1
Regulacja prędkości
2
Wskaźnik akumulatora LED
3
Przycisk zwalniający akumulator
4
Akumulator Pack
5
Przełącznik ZAŁ. / W
6
Nakrętka mocująca
7
Nakrętka kołpakowa
8
Blokada trzpienia
Ładowarka (zobacz rys. A):
9
Korytko ładownicze
10
Zasilanie
11
Wskaźnik stanu ładowania czerwony
11 a
Wskaźnik stanu ładowania zielony
Akcesoria (zobacz rys. B):
12
6 Wierteł HSS
13
2 Trzpienie do uchwytόw narzędzi
14
3 Tarcze polerskie
15
4 Tarcze szlifierskie
16
1 Szczotka metalowa
17
16 Tarcz do cięcia
18
5 Zaciskόw
19
2 Szczotki z tworzywa sztucznego
20
3 Bity do frezowania
21
2 Bity do grawerowania
22
5 Bitόw do szlifowania
23
Klucz kombi
Q
Zakres dostawy
1 Precyzyjna wiertarko-szlifierka akumulatorowa
z zestawem akumulatorów
1 Stacja ładująca z zasilaczem
1 Zestaw akcesorii (50 części)
1 Instrukcja obsługi
Q
Dane techniczne
Model PFBS 10.8 A1:
Napięcie znamionowe: 10,8 V
Obroty:
n 5000–25000 min
-1
Maks. ø tarcz: 25 mm
Zakres mocowania uchwytu
wiertarskiego
: maks. ø 3,2 mm
Akumulator Pack PFBS 10.8 A1-1:
Napięcie znamionowe: 10,8 V
Pojemność: 1300 mAh
Typ: LITOWO-JONOWY
Ładowarka PFBS 10.8 A1-2:
Pierwotnie (Wejście / Input):
Napięcie znamionowe: 230–240 V∼, 50–60 Hz
Obciążenie znamionowe:
9 W
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105

Parkside PFBS 10.8 A1 Operation and Safety Notes

Typ
Operation and Safety Notes

V iných jazykoch