Dometic VS 400 Návod na používanie

VS400

Video splitter

Installation and Operating Manual . . . . . . 8

Videosplitter

Montage- und Bedienungsanleitung . . . 20

Splitter vidéo

Instructions de montage

et de service . . . . . . . . . . . . . . . . . . . . . . . 34

Divisor de vídeo

Instrucciones de montaje y de uso . . . . . 47

Divisor de vídeo

Instruções de montagem e manual de

instruções . . . . . . . . . . . . . . . . . . . . . . . . . 61

Video splitter

Istruzioni di montaggio e d’uso . . . . . . . . 74

Videosplitter

Montagehandleiding en

gebruiksaanwijzing. . . . . . . . . . . . . . . . . . 87

Videosplitter

Monterings- og betjeningsvejledning. . 100

Video splitter

Monterings- och bruksanvisning . . . . . . 112

Videosplitter

Monterings- og bruksanvisning . . . . . . . 125

Videojakaja

Asennus- ja käyttöohje. . . . . . . . . . . . . . 137

Разветвитель видеосигнала

Инструкция по монтажу

и эксплуатации. . . . . . . . . . . . . . . . . . . . 150

Rozdzielacz sygnału wideo

Instrukcja montażu i obsługi . . . . . . . . . 163

Rozdeľovač video signálu

Návod na montáž a uvedenie

do prevádzky . . . . . . . . . . . . . . . . . . . . . 176

Videosplitter

Návod k montáži a obsluze . . . . . . . . . . 189

Videó-splitter

Szerelési és használati útmutató . . . . . . 202

OK

MENU

QUAD

EN

DE

FR

ES

PT

IT

NL

DA

SV

NO

FI

RU

PL

SK

CS

HU

DRIVING SUPPORT

PERFECTVIEW

VS400-IO-16s.book Seite 1 Dienstag, 26. Juli 2016 2:11 14

VS400-IO-16s.book Seite 2 Dienstag, 26. Juli 2016 2:11 14

VS400

3

OK

MENU

QUAD

1

2

3

1

2

3

2

1

7

2

3

5

6

4

3

VS400-IO-16s.book Seite 3 Dienstag, 26. Juli 2016 2:11 14

VS400

4

1

2

3

4

9

6

8

5

7

10

11

12

4

VS400-IO-16s.book Seite 4 Dienstag, 26. Juli 2016 2:11 14

VS400

5

6

7

VS400-IO-16s.book Seite 5 Dienstag, 26. Juli 2016 2:11 14

VS400

6

2.

1.

8

9

765432

1

0

VS400-IO-16s.book Seite 6 Dienstag, 26. Juli 2016 2:11 14

VS400

7

1

2 2

a

1

3

2

4

b

VS400-IO-16s.book Seite 7 Dienstag, 26. Juli 2016 2:11 14

Notes on using the manual VS400

EN

8

Please read this instruction manual carefully before installation and first use, and store

it in a safe place. If you pass on the product to another person, hand over this instruc-

tion manual along with it.

Table of contents

1 Notes on using the manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

2 Safety and installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

4 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

5 Technical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

6 Installing the video splitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

7 Connecting electrical power to the video splitter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

8 Operation/menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

9 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

10 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

11 Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

12 Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

1 Notes on using the manual

!

A

I

WARNING!

Safety instruction: Failure to observe this instruction can cause fatal or serious injury.

CAUTION!

Safety instruction: Failure to observe this instruction can lead to injury.

NOTICE!

Failure to observe this instruction can cause material damage and impair the function

of the product.

NOTE

Supplementary information for operating the product.

VS400-IO-16s.book Seite 8 Dienstag, 26. Juli 2016 2:11 14

VS400 Safety and installation instructions

EN

9

2 Safety and installation instructions

The manufacturer accepts no liability for damage in the following cases:

• Damage to the product resulting from mechanical influences and excess voltage

• Alterations to the product without express permission from the manufacturer

• Use for purposes other than those described in the operating manual

Please observe the prescribed safety instructions and stipulations from the vehicle

manufacturer and service workshops.

!

WARNING!

Inadequate supply cable connections could result in short circuits, which could have as

a consequence that:

• Cable fires occur

• The airbag is triggered

• Electronic control devices are damaged

• Electric functions fail (indicators, brake light, horn, ignition, lights)

A

NOTICE!

To prevent the risk of short circuits, always disconnect the negative terminal of the vehi-

cle's electrical system before working on it.

If the vehicle has an additional battery, its negative terminal should also be discon-

nected.

Please observe the following instructions:

• When working on the following cables, only use insulated cable lugs, plugs and flat push-on

receptacles:

– 30 (direct supply from positive battery terminal)

– 15 (connected positive terminal, behind the battery)

– 31 (return line from the battery, earth)

– L (indicator lights left)

– R (indicator lights right)

Do not use terminal strips.

• Use a crimping tool to connect the cables.

• When connecting to cable 31 (earth), screw the cable

– to the vehicle's earth bolt with a cable lug and a gear disc or

– to the sheet-metal bodywork with a cable lug and a self-tapping screw.

Ensure that there is a good earth connection.

VS400-IO-16s.book Seite 9 Dienstag, 26. Juli 2016 2:11 14

Safety and installation instructions VS400

EN

10

If you disconnect the negative terminal of the battery, all data stored in the volatile memories will

be lost.

• The following data must be set again, depending on the vehicle equipment options:

–Radio code

– Vehicle clock

–Timer

– On-board computer

– Seat position

You can find instructions for making these settings in the appropriate operating instructions.

Observe the following installation instructions:

!

CAUTION!

• Secure the parts installed in the vehicle in such a way that they cannot become loose

under any circumstances (sudden braking, accidents) and cause injuries to the

occupants of the vehicle.

• Secure any parts of the system covered by the bodywork in such a manner that they

cannot be come loose or damage other parts and cables or impair vehicle functions

(steering, pedals, etc).

• Always follow the safety instructions of the vehicle manufacturer.

Some work (e.g. on retention systems such as the AIRBAG etc.) may only be per-

formed by qualified specialists.

A

NOTICE!

• To prevent damage when drilling, make sure there is sufficient space on the other

side for the drill head to come out.

• Deburr all drill holes and treat them with a rust-protection agent.

Observe the following instructions when working with electrical parts:

A

NOTICE!

• When testing the voltage in electrical cables, only use a diode test lamp or a voltme-

ter.

Test lamps with an illuminant take up voltages which are too high and which can dam-

age the vehicle's electronic system.

• When making electrical connections, ensure that:

– they are not kinked or twisted

– they do not rub on edges

– they are not laid in sharp edged ducts without protection.

• Insulate all connections.

• Secure the cables against mechanical wear with cable binders or insulating tape,

for example to existing cables.

VS400-IO-16s.book Seite 10 Dienstag, 26. Juli 2016 2:11 14

VS400 Scope of delivery

EN

11

3Scope of delivery

4Intended use

The VS video splitter (ref. no. 9600000066) is used for displaying up to four camera signals on a

monitor at the same time.

5 Technical description

5.1 Function description

The system is comprised of a controller and an operating unit. The controller is installed in the

vehicle, where it is protected from moisture. The operating unit is affixed in the vehicle interior.

5.2 Connections and controls

The controller features the following connections:

No. in

fig. 1, page 3

Quantity Designation Ref. no.

11Controller –

2 1 Operating unit 9102200146

3 1 Cable set 9102200145

No. in

fig. 2, page 3

Explanation

1 Connection for operating unit

2 Connection for monitor

3 Connection for max. 4 cameras

VS400-IO-16s.book Seite 11 Dienstag, 26. Juli 2016 2:11 14

Technical description VS400

EN

12

The operating unit features the following control elements:

No. in

fig. 3, page 3

Explanation

1 MENU button

Opens settings mode.

2 QUAD button

Switches back to the last camera selected.

3

Button

Displays the image from camera 1.

In the SYSTEM SETUP menu:

moves the input field to the right.

4 OK button

Opens a sub-menu.

5

Button

Displays the image from camera 4.

In the menu: moves downwards.

6

Button

Displays the image from camera 2.

In the SYSTEM SETUP sub-menu:

moves the input field to the left.

7

Button

Displays the image from camera 3.

In the menu: moves upwards.

VS400-IO-16s.book Seite 12 Dienstag, 26. Juli 2016 2:11 14

VS400 Installing the video splitter

EN

13

6 Installing the video splitter

6.1 Tools required

For installation and assembly, you will need the following tools:

• Drill bit set (fig. 4 1, page 4)

• Electric drill (fig. 4 2, page 4)

• Screwdriver (fig. 4 3, page 4)

• Set of ring or open-ended spanners (fig. 4 4, page 4)

• Measuring ruler (fig. 4 5, page 4)

• Hammer (fig. 4 6, page 4)

• Centre punch (fig. 4 7, page 4)

To establish and test the electrical connection, the following tools are required:

• Diode test lamp (fig. 4 8, page 4) or voltmeter (fig. 4 9, page 4)

• Crimping tool (fig. 4 10, page 4)

• Insulating tape (fig. 4 11, page 4)

• Cable bushing sleeves (optional)

To secure the controller and the cables, you may require additional screws and cable binders.

!

Observe the following installation instructions:

• The installation location must be protected from moisture and be inside the vehicle.

• The installation location should be level.

• Before drilling each hole, ensure there is sufficient space on the other side for the drill head to

emerge (fig. 5, page 5).

To perform the installation, proceed as follows:

➤ Attach the controller and the operating unit to their respective installation location

provisionally.

➤ Install the rear view video system if you have not already done so.

➤ Start up the rear view video system.

If transmission of the camera image is stable, you can carry out the final installation the control-

ler and operating unit.

CAUTION!

Select the location of the modules so that they cannot injure the passengers in the vehi-

cle under any circumstances (e.g. sudden braking, road traffic accidents).

VS400-IO-16s.book Seite 13 Dienstag, 26. Juli 2016 2:11 14

Connecting electrical power to the video splitter VS400

EN

14

6.2 Installing the operating unit

I

Proceed as follows:

➤ Glue the velcro strip to the bottom of the operating unit.

➤ Glue the matching velcro strip to a suitable position in the vehicle (fig. 6, page 5).

➤ Affix the operating unit.

6.3 Installing the controller

Proceed as follows:

➤ Hold the controller at its installation location and mark the four points for the drill holes.

➤ Drill the holes, with a Ø of 3.5 mm, at each of the markings.

➤ Screw the controller in place using the 4 mm self-tapping screws (fig. 7, page 5).

7 Connecting electrical power to the video splitter

7.1 General notes on laying cables

I

Therefore, please observe the following instructions:

• Wherever possible, lay cables inside the vehicle, as they are better protected there than out-

side.

If you do need to lay a cable outside the vehicle, ensure that it is well fastened (use additional

cable ties, insulating tape etc.).

• To prevent damage to the cables when laying them, ensure that they are far enough away from

hot or moving vehicle components (exhaust pipes, drive shafts, light systems, fans, heaters,

etc.).

• Screw on the plug connections for the connecting cables to protect them against water pene-

tration (fig. 8, page 6).

NOTE

Make sure the adhesive surfaces (surface and bottom of the unit) are clean, dry and free

of grease.

NOTE

• As far as possible, use original ducts for laying the cables, or other suitable options

such as panelling edges, ventilation grilles or dummy plugs. If no openings are avail-

able, you must drill holes for the cables. Check beforehand that there is sufficient

space on the other side for the drill head to emerge.

• Cables and connections that are not properly installed will cause malfunctions or

damage to components. Correct installation of cables and connections ensures

lasting and trouble-free operation of the retrofitted components.

VS400-IO-16s.book Seite 14 Dienstag, 26. Juli 2016 2:11 14

VS400 Connecting electrical power to the video splitter

EN

15

• When laying the cables, make sure:

– they are not kinked or twisted

– they do not rub on edges

– they are not laid in sharp-edged ducts without protection (fig. 9, page 6).

• Protect every through-hole made in the bodywork against water penetration, e.g. by using a

cable with a sealant and by spraying the cable and the cable sleeve with sealant.

I

7.2 Connecting the controller

➤ Connect this connection (fig. 2 1, page 3) to the controller.

➤ Connect this connection (fig. 2 2, page 3) to the monitor.

➤ Connect the cable set (fig. 1 3, page 3) to the plug of this connection (fig. 2 3, page 3).

7.3 Connecting the cable set

The cable set features the following connections:

➤ Connect the camera connections (fig. 0 1, page 6) to the cameras.

➤ Connect the red cable (fig. 0 2, page 6) to the positive wire (+) of the vehicle.

➤ Connect the black cable (fig. 0 3, page 6) to the earth wire (–) or to earth (bodywork).

➤ Connect the green cable (fig. 0 4, page 6) to the positive wire (+) of the reversing light

(camera 1).

➤ Connect the white cable (fig. 0 5, page 6) to the control signal for camera 2.

➤ Connect the blue cable (fig. 0 6, page 6) to the control signal for camera 3.

➤ Connect the brown cable (fig. 0 7, page 6) to the control signal for camera 4.

NOTE

Only start sealing through-holes when you have completed all installation work on the

camera and have laid the required cable lengths.

No. in

fig. 0, page 6

Explanation

1 Connections for camera 1–4, 6-pin, protected from jets of water

2 12 V connection +, red

3 Earth connection –, black

4 Control input for reversing light (camera 1), green

5 Control input for camera 2, white

6 Control input for camera 3, blue

7 Control input for camera 4, brown

VS400-IO-16s.book Seite 15 Dienstag, 26. Juli 2016 2:11 14

Operation/menus VS400

EN

16

8 Operation/menus

8.1 Navigating within the menu

“Switch on”/“Switch off” menu

➤ Press the MENU button to open the menu.

➤ Press the MENU button again to close the menu.

Navigating within the menu

➤ Press the button to move upwards in the menu.

➤ Press the

button to move downwards in the menu.

The >> symbol after a menu item indicates that the item features a sub-menu.

➤ Press the OK button to open the sub-menu.

➤ Press the MENU button to quit the sub-menu.

Changing values

➤ Press the button to increase the value.

➤ Press the button to decrease the value.

Applying values

➤ Press the OK button to apply a set value.

8.2 Menu description

Main menu

Menu item Explanation

CAMERA Opens the Camera sub-menu

MODE Opens the Camera views sub-menu

AUTOSEQ Opens the automatic camera sequence sub-menu

LANGUAGE Sets the menu language

(German, English, French)

DISTANCE Shows/hides distance markers

DISTANCE ADJ Sets the values for the distance markers

(see chapter “Setting the distance markers (fig. b, page 7)” on

page 18)

SYSTEM SETUP Opens the system configuration sub-menu

RESET Resets the system to the default settings

VS400-IO-16s.book Seite 16 Dienstag, 26. Juli 2016 2:11 14

VS400 Operation/menus

EN

17

Camera sub-menu

Camera views sub-menu (MODE)

I

Automatic camera sequence sub-menu (AUTOSEQ)

System configuration sub-menu (SYSTEM SETUP)

Menu item Explanation

TITLE Sets the name of the camera

DAY/NIGHT Sets the brightness and contrast for day and night operation

BRIGHT Sets the brightness

CONTRAST Sets the contrast

COLOR Sets the colour

MIRROR Switches back and forth between mirror view and normal view

NOTE

When the monitor has been set to “dual” output, the sound from camera 1 is played.

Menu item Explanation

MODE Sets camera views (fig. b, page 7)

Dual (1), picture-in-picture, simple (2),

picture-in-picture, dual (3), quadruple (4)

Menu item Explanation

AUTOSEQ Switches the automatic camera sequence on/off

CAMERA NAME Sets the length of the display from each camera

Menu item Explanation

DATE Sets the date

TIME Sets the time

VIDEO FORMAT Sets the video format (PAL, NTSC)

VS400-IO-16s.book Seite 17 Dienstag, 26. Juli 2016 2:11 14

Troubleshooting VS400

EN

18

8.3 Setting the distance markers (fig. b, page 7)

You can shift each distance marker (1), and the side markers (2), into one of three positions.

To set the distance markers, proceed as follows:

➤ Press the MENU button to open the menu.

➤ Use the

button to select the menu item DISTANCE ADJ.

➤ Press the OK button.

➤ Press the or button to select the markers you wish to set:

✓ The markers which can be set are highlighted in red.

➤ Press the or button to set the marker highlighted in red.

➤ Press the MENU button to quit the settings.

9 Troubleshooting

10 Warranty

The statutory warranty period applies. If the product is defective, please contact the

manufacturer's branch in your country (see the back of the instruction manual for the addresses) or

your retailer.

For repair and guarantee processing, please include the following documents when you send in

the device:

• A copy of the receipt with purchasing date

• A reason for the claim or description of the fault

11 Disposal

➤ Place the packaging material in the appropriate recycling waste bins wherever possible.

M

If you wish to finally dispose of the product, ask your local recycling centre or specialist

dealer for details about how to do this in accordance with the applicable disposal regu-

lations.

Fault Suggested remedy

The monitors remains black. Ensure that the monitor is switched on.

Ensure that the controller and the monitor share a power connec-

tion.

VS400-IO-16s.book Seite 18 Dienstag, 26. Juli 2016 2:11 14

VS400 Technical data

EN

19

12 Technical data

VS

Ref. no.: 9600000066

Video standard: PAL/NTSC

Frame rate: PAL 50 frames/s

NTSC 60 frames/s

Video input: 1.0 V

P-P

, 75 Ω

Video output: 1.0 V

P-P

, 75 Ω

Resolution: PAL: 720 x 576 pixels

NTSC: 720 x 480 pixels

Operating temperature: –20 °C to +65 °C

Operating voltage: 12 – 36 Vg

Current consumption: 200 mA

Protection class: IP67

Dimensions (W x H x D): 155 x 35 x 110 mm

Weight: 500 g

Approvals:

10R-0412864

E

VS400-IO-16s.book Seite 19 Dienstag, 26. Juli 2016 2:11 14

Erklärung der Symbole VS400

DE

20

Bitte lesen Sie diese Anleitung vor Einbau und Inbetriebnahme sorgfältig durch und

bewahren Sie sie auf. Geben Sie sie im Falle einer Weitergabe des Produktes an den

Nutzer weiter.

Inhaltsverzeichnis

1 Erklärung der Symbole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

2 Sicherheits- und Einbauhinweise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

3 Lieferumfang . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

4 Bestimmungsgemäßer Gebrauch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

5 Technische Beschreibung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

6 Videosplitter montieren . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

7 Videosplitter elektrisch anschließen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

8 Bedienung/Menüs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

9 Störungsbeseitigung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

10 Gewährleistung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

11 Entsorgung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

12 Technische Daten. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

1 Erklärung der Symbole

!

A

I

WARNUNG!

Sicherheitshinweis: Nichtbeachtung kann zu Tod oder schwerer Verletzung führen.

VORSICHT!

Sicherheitshinweis: Nichtbeachtung kann zu Verletzungen führen.

ACHTUNG!

Nichtbeachtung kann zu Materialschäden führen und die Funktion des Produktes

beeinträchtigen.

HINWEIS

Ergänzende Informationen zur Bedienung des Produktes.

VS400-IO-16s.book Seite 20 Dienstag, 26. Juli 2016 2:11 14

Stránka sa načítava ...

Dometic VS 400 Návod na používanie

Táto príručka je tiež vhodná pre

Dometic VS 400 Návod na používanie

V iných jazykoch

Súvisiace články

Ďalšie dokumenty