Parkside 96760 Operation and Safety Notes

Kategória
Elektrické náradie
Typ
Operation and Safety Notes

Táto príručka je tiež vhodná pre

POWER ENGRAVING TOOL PGG 15 B1
POWER ENGRAVING TOOL
Operation and Safety Notes
Translation of original operation manual
GRA VÍR OZÓ KÉSZÜLÉK
Kezelési és biztonsági utalások
Az originál használati utasítás fordítása
APARAT ZA GRAVIRANJE
Navodila za upravljanje in varnostna opozorila
Prevod originalnega navodila za uporabo
GRA VÍR OVAČKA
Pokyny pre obsluhu a bezpečnostné pokyny
Preklad originálneho návodu na obsluhu
GRAVIERGERÄT
Bedienungs- und Sicherheitshinweise
Originalbetriebsanleitung
IAN 96760
GB Operation and Safety Notes Page 5
HU Kezelési és biztonsági utalások Oldal 19
SI Navodila za upravljanje in varnostna opozorila Stran 37
SK Pokyny pre obsluhu a bezpečnostné pokyny Strana 53
DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 67
Before reading, unfold the page containing the illustrations and familiarise yourself with all
functions of the device.
Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék
mindegyik funkcióját.
Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.
Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend
mit allen Funktionen des Gerätes vertraut.
B
1 2
45
6
A
7
3
5 GB
Table of contents
Introduction
Proper use ................................................................................ Page 6
Features and equipment ......................................................... Page 6
Included items ......................................................................... Page 7
Technical details ...................................................................... Page 7
General power tool safety warnings ......... Page 8
1. Work area safety................................................................Page 9
2. Electrical safety ................................................................... Page 9
3. Personal safety .................................................................... Page 10
4. Power tool use and care .................................................... Page 11
5. Service ................................................................................. Page 12
Operation
Switching on / off .................................................................... Page 12
Setting the cutting depth ......................................................... Page 13
Changing the engraving point ............................................... Page 13
Advice on use .......................................................................... Page 14
Cleaning ............................................................................... Page 14
Service ................................................................................... Page 15
Warranty ............................................................................. Page 15
Disposal ................................................................................ Page 16
Translation of the original declaration
of conformity / Manufacturer ............................. Page 17
6 GB
Introduction
Introduction
Power engraving tool PGG 15 B1
Introduction
We congratulate you on the purchase of your new device. You have
chosen a high quality product. The instructions for use are part of the
product. They contain important information concerning safety, use
and disposal. Before using the product, please familiarise yourself with
all of the safety information and instructions for use. Only use the unit
as described and for the specified applications. If you pass the product
on to anyone else, please ensure that you also pass on all the docu-
mentation with it.
Proper use
This product is intended for engraving or decorating materials such
as metal, plastic, glass, ceramic, wood, leather and stone. Any other
use or modification to the drill / grinder shall be considered as improper
use and could give rise to considerable dangers. The manufacturer will
not accept liability for loss or damage arising from improper use. Not
intended for commercial use.
Features and equipment
1
ON / OFF switch
2
Stroke rate rotary controller
3
Hanging eye
4
Mains lead
7 GB
Introduction
Introduction
5
Engraving point
6
Engraving point holder
7
Engraving stencils
Included items
1 Power engraving tool PGG 15 B1
2 Engraving stencils
1 Operating instructions
Technical details
Rated voltage: 230 V∼ 50 Hz
Mode of operation: intermittent operation: S3 20 %
Note: A duty cycle (in %) defines explicitly the maximum continuous
duration of use and the subsequent rest period. In this case the tool
requires a cooling phase of eight minutes after an operating period of
two minutes, for example.
Rated current: 0.15 A
Stroke rate: 6000 min
-1
Noise and vibration data:
Measured values for noise are determined in accordance with
EN 60745. The A-weighted noise level of the electrical power tool
are typically:
Sound pressure level: 74.4 dB(A)
Sound power level: 85.4 dB(A)
Uncertainty K: 3 dB
8 GB
General power tool safety warnings
Introduction / General power tool safety warnings
Wear ear protection!
Evaluated acceleration, typical:
Hand / arm vibration: 1.582 m / s
2
Uncertainty K = 1.5 m / s
2
The vibration level specified in these instructions was
measured in accordance with an EN 60745 standardised measurement
process and can be used to compare equipment. The vibration emission
value specified can also serve as a preliminary assessment of the ex-
posure.
The vibration level will change according to the application of the elec-
trical tool an in some cases may exceed the value specified in these in-
structions. Regularly using the electric tool in such a way may make it
easy to underestimate the vibration.
Note: If you wish to make an accurate assessment of the vibration
loads experienced during a particular period of working, you should
also take into account the intervening periods of time when the device
is switched off or is running but is not actually in use. This can result in
a much lower vibration load over the whole of the period of working.
General power tool safety warnings
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and instructions may result in
electric shock, fire and / or serious injury.
Save all warnings and instructions for future reference.
9 GB
General power tool safety warnings
Introduction / General power tool safety warnings
The term “power tool” in the warnings refers to your mains-operated
(corded) power tool or battery-operated (cordless) power tool.
1. Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
b) Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
2. Electrical safety
a) Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators.
There
is an increased risk of electric shock if your body is earthed or
grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carry-
ing, pulling or unplugging the power tool. Keep cord
away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.
10 GB
General power tool safety warnings
General power tool safety warnings
e) When operating a power tool outdoors, use an exten-
sion cord suitable for outdoor use. Use of a cord suitable
for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoid-
able, use a residual current device (RCD) protected
supply. Use of an RCD reduces the risk of electric shock.
3. Personal safety
a) Stay alert, watch what you are doing and use com-
mon sense when operating a power tool. Do not use a
power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for appropri-
ate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and / or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energising
power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a rotat-
ing part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool in un-
expected situations.
f) Dress properly. Do not wear loose clothing or jewel-
lery. Keep your hair, clothing and gloves away from
11 GB
General power tool safety warnings
General power tool safety warnings
moving parts. Loose clothes, jewellery or long hair can be
caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
4. Power tool use and care
a) Do not force the power tool. Use the correct power
tool for your applica
tion. The correct power tool will do the
job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and / or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the risk
of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power tools
are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s oper-
ation. If damaged, have the power tool repaired before
use. Many accidents are caused by poorly maintained power tools.
12 GB
Operation
General power tool safety warnings / Operation
f) Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind and
are easier to control.
g) Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into account
the working conditions and the work to be performed.
Use of the power tool for operations different from those intended
could result in a hazardous situation.
5. Service
a) Have your power tool serviced by a
qualified repair
person using only
identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Operation
Never use the device for a purpose for which it was not intended or
with non-original parts / accessories. The use of tools or accessories
other than those recommended in the operating instructions could lead
to you suffering an injury.
Switching on / off
Insert the mains plug into a mains socket.
Switching on:
Press the ON / OFF switch
1
.
13 GB
Operation
General power tool safety warnings / Operation
Switching off:
Release the ON / OFF switch
1
.
Setting the cutting depth
The cutting depth of the engraver is set using the stroke rate rotary control-
ler
2
. A low setting is usually sufficient for most common applications.
Turn the stroke rate rotary controller
2
towards the + sign to in-
crease the cutting depth.
Turn the stroke rate rotary controller
2
towards the - sign to de-
crease the cutting depth.
Note: Take care when increasing the cutting depth not to turn the stroke
rate rotary controller
2
too far towards the + sign. Otherwise the switch
could screw off the device.
Changing the engraving point
RISK OF INJURY! Switch the device off before
performing any tasks on the device and pull the mains plug out of the
mains socket.
Replace the engraving point
5
as soon as it becomes too worn
and no longer provides the desired engraving performance. Turn
the engraving point holder
6
anticlockwise until the engraving
point
5
is released.
Remove the spring and the plain washer.
14 GB
Service / Warranty
Operation / Cleaning
Push the plain washer and spring on to a new engraving point
5
.
Then insert this and turn the engraving point holder
6
clockwise
to lock the engraving point in position.
Ensure that the engraving point
5
is properly fixed in position.
Advice on use
You can use the mini-engraver to produce creative, individual engravings.
For example, you can use it to place identifying marks on your valuables.
You can engrave numbers and letters into metal, glass, wood, plastic,
ceramic, stone and leather. This is done with the help of the supplied
engraving stencils
7
, see Figs. A and B.
Hold the device at an angle, as you would a pencil.
Your arm should rest on the table.
Using very light pressure, guide the engraving point
5
over the
workpiece. Find the ideal speed of movement by trial and error on
a piece of waste material.
Note: The engraving point
5
supplied with the product is made
from tungsten steel. Therefore it is not suitable for engraving electronic
media such as CDs, DVDs etc. It could damage these materials and
render them illegible.
Cleaning
Before performing any cleaning or maintenance
work, always remove the mains plug from the socket.
Clean all the dirt off the device. Use a dry cloth for cleaning.
15 GB
Service / Warranty
Operation / Cleaning
Service
Have your device repaired at the ser-
vice centre or by qualified specialist personnel using
original manufacturer parts only. This will ensure that your
device remains safe to use.
If the plug or lead needs to be replaced,
always have the replacement carried out by the man-
ufacturer or its service centre. This will ensure that your device
remains safe to use.
Note: Spare parts not listed (e.g. carbon brushes, switches) can be
ordered through our call centre.
Warranty
The warranty for this appliance is for 3 years from the
date of purchase. The appliance has been manufactured
with care and meticulously examined before delivery.
Please retain your receipt as proof of purchase. In the
event of a warranty claim, please make contact by tele-
phone with our Service Department. Only in this way can
a post-free despatch for your goods be assured.
The warranty covers only claims for material and maufacturing defects,
but not for transport damage, for wearing parts or for damage to frag-
ile components, e.g. buttons or batteries. This product is for private use
only and is not intended for commercial use.
The warranty is void in the case of abusive and improper handling, use
of force and internal tampering not carried out by our authorized service
16 GB
/ Translation of the original declaration of conformity /
Warranty / Disposal
branch. Your statutory rights are not restricted in any way by this war-
ranty.
T
he warranty period will not be extended by repairs made unter warran
ty.
This applies also to replaced and repaired parts. Any damage and de-
fects extant on purchase must be reported immediately after unpacking
th
e appliance, at the latest, two days after the purchase date. Repairs mad
e
after the expiration of the warranty period are subject to payment.
GB
Service Great Britain
Tel.: 0871 5000 720
(0.10 GBP/Min.)
e-mail: komper[email protected]
IAN 96760
Disposal
The packaging is wholly composed of environmentally-
friendly materials that can be disposed of at a local
recycling centre.
Do not dispose of electric tools in
the household waste!
In accordance with European Directive 2012 / 19 / EU about waste
electrical and electronic equipment and its transposition into national
legislation, worn out electric tools must be collected separately and
taken for environmentally compatible recycling.
17 GB
/ Translation of the original declaration of conformity /
Warranty / Disposal
Contact your local refuse disposal authority for more details of how to
dispose of your worn out electrical devices.
Translation of the original declaration of
conformity / Manufacturer
We, KOMPERNASS HANDELS GMBH, the person responsible for
documents: Mr Semi Uguzlu, BURG STRASSE 21, 44867 BOCHUM,
GERMANY, hereby declare that this product complies with the following
standards, normative documents and EU directives:
Machinery Directive
(2006 / 42 / EC)
EU Low Voltage Directive
(2006 / 95 / EC)
Electromagnetic compatibility
(2004 / 108 / EC)
RoHS Directive
(2011 / 65 / EU)
Applicable harmonized standards
EN 60745-1/A11:2010
EN ISO 12100:2010
EN 55014-1/A2:2011
EN 55014-2/A2:2008
EN 61000-3-2/A2:2009
EN 61000-3-3:2008
18 GB
Translation of the original declaration … / Manufacturer
Type / Device description:
Power engraving tool PGG 15 B1
Date of manufacture (DOM): 04–2014
Serial number: IAN 96760
Bochum, 30.04.2014
Semi Uguzlu
- Quality Manager -
We reserve the right to make technical modifications in the course of
further development.
Tartalomjegyzék
19 HU
Translation of the original declaration … / Manufacturer
Tartalomjegyzék
Bevezetés
Rendeltetésszerű használat ...................................................Oldal 20
Felszerelés ..............................................................................Oldal 20
A szállítmány tartalma ...........................................................Oldal 21
Műszaki adatok .....................................................................Oldal 21
Elektromos szerszámokra vonatkozó
általános biztonsági tudnivalók
....................Oldal 22
1. A munkahely biztonsága ..................................................Oldal 23
2. Elektromos biztonsága ......................................................Oldal 23
3. Személyek biztonsága ......................................................Oldal 24
4. Az elektromos szerszámokkal való gondos járás
és azok gondos használata ..................................................Oldal 26
5. Szervíz ................................................................................Oldal 27
Kezelés
Be- / kikapcsolás .....................................................................Oldal 27
Löketmélység beállítása .........................................................Oldal 28
A gravírozó hegy kicserélése ................................................ Oldal 28
A munkára vonatkozó tudnivalók .........................................Oldal 29
Tisztítás .................................................................................Oldal 29
Szerviz ..................................................................................Oldal 30
Garancia .............................................................................Oldal 30
Mentesítés .........................................................................Oldal 31
Az eredeti EU-Megfelelőségi
Nyilatkozat fordítása / Gyártó
........................ Oldal 32
Jótállási tájékoztató ................................................. Oldal 34
20 HU
Bevezetés
Bevezetés
Gravírozó készülék, PGG 15 B1
Bevezetés
Gratulálunk új készülékének vásárlása alkalmából. Ezzel a döntésével
vállalatunk értékes terméke mellett döntött.
A használati utasítás ezen ter-
mék része. A biztonságra,
a használatára és a megsemmisítésre vonat-
kozó fontos tudnivalókat tartalmazza. A termék használata előtt ismerje
meg az összes használati és biztonsági tudnivalót. A terméket csak a
leírtak szerint és a megadott felhasználási területeken alkalmazza. A
termék harmadik személy számára való továbbadása esetén kézbesítse
vele annak a teljes dokumentációját is.
Rendeltetésszerű használat
Ez a készülék fém, műanyag, üveg, kerámia, fa, bőr és kő gravírozására,
vagy díszítésére szolgál. Mindens irányú használat vagy a készülék
megváltoztatása nem rendeltetésszerűnek számit és jelentős veszélyek-
kel jár. A nem rendeltetésszerű alkalmazásból eredő károkért a gyár
nem áll jót. A készülék nem ipari használatra való.
Felszerelés
1
BE- / KI-kapcsoló
2
löketszám- szabályozó gomb
3
fülecs
4
hálózati kábel
5
gravírozó hegy
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83

Parkside 96760 Operation and Safety Notes

Kategória
Elektrické náradie
Typ
Operation and Safety Notes
Táto príručka je tiež vhodná pre

V iných jazykoch