Parkside 96760 Operation and Safety Notes

POWER ENGRAVING TOOL PGG 15 B1

POWER ENGRAVING TOOL

Operation and Safety Notes

Translation of original operation manual

GRA VÍR OZÓ KÉSZÜLÉK

Kezelési és biztonsági utalások

Az originál használati utasítás fordítása

APARAT ZA GRAVIRANJE

Navodila za upravljanje in varnostna opozorila

Prevod originalnega navodila za uporabo

GRA VÍR OVAČKA

Pokyny pre obsluhu a bezpečnostné pokyny

Preklad originálneho návodu na obsluhu

GRAVIERGERÄT

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung

IAN 96760

GB Operation and Safety Notes Page 5

HU Kezelési és biztonsági utalások Oldal 19

SI Navodila za upravljanje in varnostna opozorila Stran 37

SK Pokyny pre obsluhu a bezpečnostné pokyny Strana 53

DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 67

Before reading, unfold the page containing the illustrations and familiarise yourself with all

functions of the device.

Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék

mindegyik funkcióját.

Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.

Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend

mit allen Funktionen des Gerätes vertraut.

B

1 2

45

6

A

7

3

5 GB

Table of contents

Introduction

Proper use ................................................................................ Page 6

Features and equipment ......................................................... Page 6

Included items ......................................................................... Page 7

Technical details ...................................................................... Page 7

General power tool safety warnings ......... Page 8

1. Work area safety................................................................Page 9

2. Electrical safety ................................................................... Page 9

3. Personal safety .................................................................... Page 10

4. Power tool use and care .................................................... Page 11

5. Service ................................................................................. Page 12

Operation

Switching on / off .................................................................... Page 12

Setting the cutting depth ......................................................... Page 13

Changing the engraving point ............................................... Page 13

Advice on use .......................................................................... Page 14

Cleaning ............................................................................... Page 14

Service ................................................................................... Page 15

Warranty ............................................................................. Page 15

Disposal ................................................................................ Page 16

Translation of the original declaration

of conformity / Manufacturer ............................. Page 17

6 GB

Introduction

Power engraving tool PGG 15 B1

Introduction

We congratulate you on the purchase of your new device. You have

chosen a high quality product. The instructions for use are part of the

product. They contain important information concerning safety, use

and disposal. Before using the product, please familiarise yourself with

all of the safety information and instructions for use. Only use the unit

as described and for the speciﬁed applications. If you pass the product

on to anyone else, please ensure that you also pass on all the docu-

mentation with it.

Proper use

This product is intended for engraving or decorating materials such

as metal, plastic, glass, ceramic, wood, leather and stone. Any other

use or modiﬁcation to the drill / grinder shall be considered as improper

use and could give rise to considerable dangers. The manufacturer will

not accept liability for loss or damage arising from improper use. Not

intended for commercial use.

Features and equipment

1

ON / OFF switch

2

Stroke rate rotary controller

3

Hanging eye

4

Mains lead

7 GB

Introduction

5

Engraving point

6

Engraving point holder

7

Engraving stencils

Included items

1 Power engraving tool PGG 15 B1

2 Engraving stencils

1 Operating instructions

Technical details

Rated voltage: 230 V∼ 50 Hz

Mode of operation: intermittent operation: S3 20 %

Note: A duty cycle (in %) deﬁnes explicitly the maximum continuous

duration of use and the subsequent rest period. In this case the tool

requires a cooling phase of eight minutes after an operating period of

two minutes, for example.

Rated current: 0.15 A

Stroke rate: 6000 min

-1

Noise and vibration data:

Measured values for noise are determined in accordance with

EN 60745. The A-weighted noise level of the electrical power tool

are typically:

Sound pressure level: 74.4 dB(A)

Sound power level: 85.4 dB(A)

Uncertainty K: 3 dB

8 GB

General power tool safety warnings

Introduction / General power tool safety warnings

Wear ear protection!

Evaluated acceleration, typical:

Hand / arm vibration: 1.582 m / s

2

Uncertainty K = 1.5 m / s

2

The vibration level speciﬁed in these instructions was

measured in accordance with an EN 60745 standardised measurement

process and can be used to compare equipment. The vibration emission

value speciﬁed can also serve as a preliminary assessment of the ex-

posure.

The vibration level will change according to the application of the elec-

trical tool an in some cases may exceed the value speciﬁed in these in-

structions. Regularly using the electric tool in such a way may make it

easy to underestimate the vibration.

Note: If you wish to make an accurate assessment of the vibration

loads experienced during a particular period of working, you should

also take into account the intervening periods of time when the device

is switched oﬀ or is running but is not actually in use. This can result in

a much lower vibration load over the whole of the period of working.

General power tool safety warnings

Read all safety warnings and all instruc-

tions. Failure to follow the warnings and instructions may result in

electric shock, ﬁre and / or serious injury.

Save all warnings and instructions for future reference.

9 GB

General power tool safety warnings

Introduction / General power tool safety warnings

The term “power tool” in the warnings refers to your mains-operated

(corded) power tool or battery-operated (cordless) power tool.

1. Work area safety

a) Keep work area clean and well lit. Cluttered or dark areas

invite accidents.

b) Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Power tools create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose control.

2. Electrical safety

a) Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodiﬁed plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces,

such as pipes, radiators, ranges and refrigerators.

There

is an increased risk of electric shock if your body is earthed or

grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carry-

ing, pulling or unplugging the power tool. Keep cord

away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock.

10 GB

General power tool safety warnings

e) When operating a power tool outdoors, use an exten-

sion cord suitable for outdoor use. Use of a cord suitable

for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoid-

able, use a residual current device (RCD) protected

supply. Use of an RCD reduces the risk of electric shock.

3. Personal safety

a) Stay alert, watch what you are doing and use com-

mon sense when operating a power tool. Do not use a

power tool while you are tired or under the influence

of drugs, alcohol or medication. A moment of inattention

while operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protection used for appropri-

ate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in

the off-position before connecting to power source

and / or battery pack, picking up or carrying the tool.

Carrying power tools with your ﬁnger on the switch or energising

power tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a rotat-

ing part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool in un-

expected situations.

f) Dress properly. Do not wear loose clothing or jewel-

lery. Keep your hair, clothing and gloves away from

11 GB

General power tool safety warnings

moving parts. Loose clothes, jewellery or long hair can be

caught in moving parts.

g) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

4. Power tool use and care

a) Do not force the power tool. Use the correct power

tool for your applica

tion. The correct power tool will do the

job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and / or

the battery pack from the power tool before making

any adjustments, changing accessories, or storing

power tools. Such preventive safety measures reduce the risk

of starting the power tool accidentally.

d) Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power tools

are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s oper-

ation. If damaged, have the power tool repaired before

use. Many accidents are caused by poorly maintained power tools.

12 GB

Operation

General power tool safety warnings / Operation

f) Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to bind and

are easier to control.

g) Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into account

the working conditions and the work to be performed.

Use of the power tool for operations diﬀerent from those intended

could result in a hazardous situation.

5. Service

a) Have your power tool serviced by a

qualified repair

person using only

identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Operation

Never use the device for a purpose for which it was not intended or

with non-original parts / accessories. The use of tools or accessories

other than those recommended in the operating instructions could lead

to you suﬀering an injury.

Switching on / oﬀ

Insert the mains plug into a mains socket.

Switching on:

Press the ON / OFF switch

1

.

13 GB

Operation

General power tool safety warnings / Operation

Switching off:

Release the ON / OFF switch

1

.

Setting the cutting depth

The cutting depth of the engraver is set using the stroke rate rotary control-

ler

2

. A low setting is usually suﬃcient for most common applications.

Turn the stroke rate rotary controller

2

towards the + sign to in-

crease the cutting depth.

Turn the stroke rate rotary controller

2

towards the - sign to de-

crease the cutting depth.

Note: Take care when increasing the cutting depth not to turn the stroke

rate rotary controller

2

too far towards the + sign. Otherwise the switch

could screw oﬀ the device.

Changing the engraving point

RISK OF INJURY! Switch the device oﬀ before

performing any tasks on the device and pull the mains plug out of the

mains socket.

Replace the engraving point

5

as soon as it becomes too worn

and no longer provides the desired engraving performance. Turn

the engraving point holder

6

anticlockwise until the engraving

point

5

is released.

Remove the spring and the plain washer.

14 GB

Service / Warranty

Operation / Cleaning

Push the plain washer and spring on to a new engraving point

5

.

Then insert this and turn the engraving point holder

6

clockwise

to lock the engraving point in position.

Ensure that the engraving point

5

is properly ﬁxed in position.

Advice on use

You can use the mini-engraver to produce creative, individual engravings.

For example, you can use it to place identifying marks on your valuables.

You can engrave numbers and letters into metal, glass, wood, plastic,

ceramic, stone and leather. This is done with the help of the supplied

engraving stencils

7

, see Figs. A and B.

Hold the device at an angle, as you would a pencil.

Your arm should rest on the table.

Using very light pressure, guide the engraving point

5

over the

workpiece. Find the ideal speed of movement by trial and error on

a piece of waste material.

Note: The engraving point

5

supplied with the product is made

from tungsten steel. Therefore it is not suitable for engraving electronic

media such as CDs, DVDs etc. It could damage these materials and

render them illegible.

Cleaning

Before performing any cleaning or maintenance

work, always remove the mains plug from the socket.

Clean all the dirt oﬀ the device. Use a dry cloth for cleaning.

15 GB

Service / Warranty

Operation / Cleaning

Service

Have your device repaired at the ser-

vice centre or by qualified specialist personnel using

original manufacturer parts only. This will ensure that your

device remains safe to use.

If the plug or lead needs to be replaced,

always have the replacement carried out by the man-

ufacturer or its service centre. This will ensure that your device

remains safe to use.

Note: Spare parts not listed (e.g. carbon brushes, switches) can be

ordered through our call centre.

Warranty

The warranty for this appliance is for 3 years from the

date of purchase. The appliance has been manufactured

with care and meticulously examined before delivery.

Please retain your receipt as proof of purchase. In the

event of a warranty claim, please make contact by tele-

phone with our Service Department. Only in this way can

a post-free despatch for your goods be assured.

The warranty covers only claims for material and maufacturing defects,

but not for transport damage, for wearing parts or for damage to frag-

ile components, e.g. buttons or batteries. This product is for private use

only and is not intended for commercial use.

The warranty is void in the case of abusive and improper handling, use

of force and internal tampering not carried out by our authorized service

16 GB

… / Translation of the original declaration of conformity / …

Warranty / Disposal

branch. Your statutory rights are not restricted in any way by this war-

ranty.

T

he warranty period will not be extended by repairs made unter warran

ty.

This applies also to replaced and repaired parts. Any damage and de-

fects extant on purchase must be reported immediately after unpacking

th

e appliance, at the latest, two days after the purchase date. Repairs mad

e

after the expiration of the warranty period are subject to payment.

GB

Service Great Britain

Tel.: 0871 5000 720

(0.10 GBP/Min.)

e-mail: komper[email protected]

IAN 96760

Disposal

The packaging is wholly composed of environmentally-

friendly materials that can be disposed of at a local

recycling centre.

Do not dispose of electric tools in

the household waste!

In accordance with European Directive 2012 / 19 / EU about waste

electrical and electronic equipment and its transposition into national

legislation, worn out electric tools must be collected separately and

taken for environmentally compatible recycling.

17 GB

… / Translation of the original declaration of conformity / …

Warranty / Disposal

Contact your local refuse disposal authority for more details of how to

dispose of your worn out electrical devices.

Translation of the original declaration of

conformity / Manufacturer

We, KOMPERNASS HANDELS GMBH, the person responsible for

documents: Mr Semi Uguzlu, BURG STRASSE 21, 44867 BOCHUM,

GERMANY, hereby declare that this product complies with the following

standards, normative documents and EU directives:

Machinery Directive

(2006 / 42 / EC)

EU Low Voltage Directive

(2006 / 95 / EC)

Electromagnetic compatibility

(2004 / 108 / EC)

RoHS Directive

(2011 / 65 / EU)

Applicable harmonized standards

EN 60745-1/A11:2010

EN ISO 12100:2010

EN 55014-1/A2:2011

EN 55014-2/A2:2008

EN 61000-3-2/A2:2009

EN 61000-3-3:2008

18 GB

Translation of the original declaration … / Manufacturer

Type / Device description:

Power engraving tool PGG 15 B1

Date of manufacture (DOM): 04–2014

Serial number: IAN 96760

Bochum, 30.04.2014

Semi Uguzlu

- Quality Manager -

We reserve the right to make technical modiﬁcations in the course of

further development.

Tartalomjegyzék

19 HU

Translation of the original declaration … / Manufacturer

Tartalomjegyzék

Bevezetés

Rendeltetésszerű használat ...................................................Oldal 20

Felszerelés ..............................................................................Oldal 20

A szállítmány tartalma ...........................................................Oldal 21

Műszaki adatok .....................................................................Oldal 21

Elektromos szerszámokra vonatkozó

általános biztonsági tudnivalók

....................Oldal 22

1. A munkahely biztonsága ..................................................Oldal 23

2. Elektromos biztonsága ......................................................Oldal 23

3. Személyek biztonsága ......................................................Oldal 24

4. Az elektromos szerszámokkal való gondos járás

és azok gondos használata ..................................................Oldal 26

5. Szervíz ................................................................................Oldal 27

Kezelés

Be- / kikapcsolás .....................................................................Oldal 27

Löketmélység beállítása .........................................................Oldal 28

A gravírozó hegy kicserélése ................................................ Oldal 28

A munkára vonatkozó tudnivalók .........................................Oldal 29

Tisztítás .................................................................................Oldal 29

Szerviz ..................................................................................Oldal 30

Garancia .............................................................................Oldal 30

Mentesítés .........................................................................Oldal 31

Az eredeti EU-Megfelelőségi

Nyilatkozat fordítása / Gyártó

........................ Oldal 32

Jótállási tájékoztató ................................................. Oldal 34

20 HU

Bevezetés

Gravírozó készülék, PGG 15 B1

Bevezetés

Gratulálunk új készülékének vásárlása alkalmából. Ezzel a döntésével

vállalatunk értékes terméke mellett döntött.

A használati utasítás ezen ter-

mék része. A biztonságra,

a használatára és a megsemmisítésre vonat-

kozó fontos tudnivalókat tartalmazza. A termék használata előtt ismerje

meg az összes használati és biztonsági tudnivalót. A terméket csak a

leírtak szerint és a megadott felhasználási területeken alkalmazza. A

termék harmadik személy számára való továbbadása esetén kézbesítse

vele annak a teljes dokumentációját is.

Rendeltetésszerű használat

Ez a készülék fém, műanyag, üveg, kerámia, fa, bőr és kő gravírozására,

vagy díszítésére szolgál. Minden más irányú használat vagy a készülék

megváltoztatása nem rendeltetésszerűnek számit és jelentős veszélyek-

kel jár. A nem rendeltetésszerű alkalmazásból eredő károkért a gyártó

nem áll jót. A készülék nem ipari használatra való.

Felszerelés

1

BE- / KI-kapcsoló

2

löketszám- szabályozó gomb

3

fülecs

4

hálózati kábel

5

gravírozó hegy

Stránka sa načítava ...

Parkside 96760 Operation and Safety Notes

Táto príručka je tiež vhodná pre

Parkside 96760 Operation and Safety Notes

V iných jazykoch

Súvisiace články

Ďalšie dokumenty