Parkside PKLL 10 B3 Translation Of The Original Instructions

SELF-LEVELLING CROSS LINE

LASER LEVEL PKLL 10 B3

KERESZTVONALAS LÉZER

Az originál használati utasítás fordítása

SELF-LEVELLING CROSS

LINE LASER LEVEL

Translation of the original instructions

KRIŽNO LINIJSKI LASER

Prevod originalnega navodila za uporabo

K

ŘÍŽOVÝ LINIOVÝ LASER

Překlad originálního provozního návodu

IAN 338152_2001

KREUZLINIENLASER

Originalbetriebsanleitung

SELF-LEVELLING CROSS LINE

LASER LEVEL PKLL 10 B3

GB Translation of the original instructions Page 5

HU Az originál használati utasítás fordítása Oldal 17

SI Prevod originalnega

navodila za uporabo Stran 29

CZ Překlad originálního provozního návodu Strana 41

DE / AT / CH Originalbetriebsanleitung Seite 52

H

V

1 2

7

8

10

11 a

11

13

14

15

12

16

17

18

19

9 3

4

5 a

6

A

C

5 a

1

2

B

6

5

5 GB

List of pictograms used ............................................ Page 6

Introduction ....................................................................... Page 6

Intended use ............................................................................ Page 6

Description of parts ................................................................. Page 7

Scope of delivery .................................................................... Page 7

Technical data ......................................................................... Page 8

Safety notes ...................................................................... Page 8

Safety instructions for batteries / rechargeable batteries ..... Page 10

Initial use ............................................................................. Page 11

Inserting / Changing batteries ................................................ Page 11

Switching on / off .................................................................... Page 11

Use automatic levelling system............................................... Page 11

Using individual lines and crossed lines ................................ Page 12

Working without the automatic levelling system ................... Page 12

Practical guidance .................................................................. Page 12

Working with the tripod .......................................................... Page 13

Maintenance and cleaning ................................... Page 14

Storage ................................................................................. Page 14

Disposal ................................................................................ Page 14

Warranty ............................................................................. Page 15

Warranty claim procedure ..................................................... Page 16

Service ..................................................................................... Page 16

6 GB

List of pictograms used

Please read the instructions for use.

Danger of explosion!

Wear safety gloves!

Attention!

Protect yourself from laser radiation!

Do not stare into the laser beam!

Direct current / voltage

Including batteries

Self-levelling cross line laser level

Introduction

We congratulate you on the purchase of your new product.

You have chosen a high quality product. The instructions for

use are part of the product. They contain important information

concerning safety, use and disposal. Before using the product, please

familiarise yourself with all of the safety information and instructions for

use. Only use the product as described and for the speciﬁed

applications.

If you pass the product on to anyone else, please ensure that you also

pass on all the documentation with it.

Intended use

The product is suitable for the the determination and veriﬁcation of

horizontal and vertical lines. The product is exclusively suitable for use

7 GB

in enclosed operating sites. Any other use or modiﬁcation of the product

shall be considered improper use and may result in serious accidents.

The manufacturer assumes no liability for damages due to improper use.

Not intended for commercial purposes.

Description of parts

1

H-button to switch on / oﬀ horizontal line

2

LED indicator (red: levelling oﬀ, green levelling on)

3

V-button to switch on / oﬀ vertical line

4

LOCK switch

5

Battery compartment

5 a

Battery compartment cover

6

- Tripod thread (underneath)

7

Laser beam opening

8

- quick-release ﬁxing screw (to align with tripod thread of

cross line laser)

9

Metal bracket (to adjust screw on the quick shoe)

10

Locking screw (to adjust the angle of tripod ﬂat head to up

to 90 degree)

11

Bubble level

11a

Lever (to ﬁx the quick shoe)

12

Long Handle

13

Locking screw (to rotate the tripod ﬂat head up to 360 degree

horizontally)

14

Locking screw (to adjust the height of the centre column)

15

Plastic ring

16

Blocking lever (to adjust the height of the legs)

17

Legs of the tripod

18

Tripod ﬂat head

19

Quick shoe

Scope of delivery

1 Self-levelling cross line laser level

1 Tripod

2 1.5 V-Batteries, Type AA

1 Set of instructions for use

8 GB

Technical data

Operating voltage: 3 V (direct current)

Working area at least

1)

: 10 m

Levelling accuracy: +/- 0.5 mm / m

Typical self-levelling range: ± 4°

Typical levelling time: approx. 4 seconds

Operating temperature: +5 °C–35 °C

Max. relative humidity: ≤ 90 %

Laser class: 2

Wave length (λ): 635 nm

Maximum performance

P max: 1 mW

Tripod mount:

Batteries: 2 x 1.5 V-Batteries, Type AA

Product weight: 260 g (without batteries)

Tripod weight: 320 g

Product dimensions: approx. 70 x 61 x 90 mm

Tripod dimensions: 65 cm

1) The operating range can be reduced by unfavourable environmental

conditions (e.g. direct sunlight).

Safety notes

DANGER OF SUFFOCATION! Packaging materials (e.g. ﬁlms or

polystyrene) can not be used as toys. Always keep children away

from the packaging material. The packaging material is not a toy.

Do not work with the measuring tool in an environment where there

is a danger of explosion, where there are ﬂammable liquids, gasses

or dusts. Sparks can be created in the product, which could ignite

dust or fumes.

This product may be used by children from the age of 8, by per-

sons of reduced physical, sensory or mental abilities or a lack of

experience and / or knowledge if they are supervised or instructed

with regard to the safe use of the product and have understood

the risks resulting from use. Do not allow children to play with the

product. Cleaning and user maintenance may not be carried out

by children unless they are supervised.

Do not leave the switched-on product unattended and switch the

product oﬀ after use. Others could be blinded by the laser beam.

Risk of eye injury.

Do not expose the product to moisture or direct sunlight.

9 GB

Do not expose the product to extremely high temperatures or tem-

perature ﬂuctuations. For example, do not leave it in your car for a

long time. In the case of large temperature ﬂuctuations, let the product

acclimatise before using it. In extreme temperatures or temperature

ﬂuctuations, the precision of the product can be impaired.

Avoid strong impacts against the measuring tool. Damage to the

measuring tool can impair its accuracy. After a strong impact com-

pare the laser line with a known vertical or horizontal reference

line to check it.

Turn the measuring tool oﬀ when you transport it. When it is switched

oﬀ the pendulum unit is locked, which otherwise can be damaged

in strong movements.

Do not bring the measuring tool near to heart pacemakers. The

magnet inside the measuring tool creates a ﬁeld that can impair

the function of pacemakers.

Keep the measuring tool away from magnetic data carriers and

devices that are sensitive to magnetic inﬂuences. The eﬀects of the

magnet can lead to irreversible data losses.

Protect yourself from laser radiation!

LASER

2

P

max

< 1 mW

λ = 635 nm

EN 60825-1:2014

Do not look directly into the laser beam or the laser beam

opening

7

.

Viewing the laser beam with optical instruments

(e.g. loupe, magnifying glass etc.) is associated with risk injury to

the eyes.

CAUTION! If operating or adjusting devices than other than those

described here are used or other procedures are carried out, this

can lead to dangerous radiation eﬀects.

Never direct the laser beam at people, animals or reﬂective sur-

faces. Even looking brieﬂy into the laser beam can cause damage

to the eyes.

10 GB

Safety instructions for batteries /

rechargeable batteries

DANGER TO LIFE! Keep batteries / rechargeable batteries out

of reach of children. If accidentally swallowed seek immediate

medical attention.

Swallowing may lead to burns, perforation of soft tissue, and

death. Severe burns can occur within 2 hours of ingestion.

DANGER OF EXPLOSION! Never recharge non-re-

chargeable batteries. Do not short-circuit batteries / re-

chargeable batteries and / or open them. Overheating,

ﬁre or bursting can be the result.

Never throw batteries / rechargeable batteries into ﬁre or water.

Do not exert mechanical loads to batteries / rechargeable batteries.

Risk of leakage of batteries / rechargeable batteries

Avoid extreme environmental conditions and temperatures, which

could aﬀect batteries / rechargeable batteries, e.g. radiators / direct

sunlight.

If batteries / rechargeable batteries have leaked, avoid contact

with skin, eyes and mucous membranes with the chemicals! Flush

immediately the aﬀected areas with fresh water and seek medical

attention!

WEAR PROTECTIVE GLOVES! Leaked or damaged

batteries / rechargeable batteries can cause burns on

contact with the skin. Wear suitable protective gloves at

all times if such an event occurs.

In the event of a leakage of batteries / rechargeable batteries, im-

mediately remove them from the product to prevent damage.

Only use the same type of batteries / rechargeable batteries. Do

not mix used and new batteries / rechargeable batteries.

Remove batteries / rechargeable batteries if the product will not be

used for a longer period.

Risk of damage of the product

Only use the speciﬁed type of battery / rechargeable battery!

Insert batteries / rechargeable batteries according to polarity

marks (+) and (-) on the battery / rechargeable battery and the

product.

Use a dry lint-free cloth or cotton swab to clean the contacts on

the battery / rechargeable battery and in the battery compartment

before inserting!

Remove exhausted batteries / rechargeable batteries from the

product immediately.

11 GB

Initial use

Check that the delivery is complete and that there is no visible

damage.

Remove the packaging material from the product.

Inserting / Changing batteries

Open the battery compartment cover

5 a

(see ﬁg. B).

Insert batteries into the battery compartment

5

(see ﬁg. C). Make

sure that the batteries are inserted in a correct polarity (see ﬁg. C)

before closing back the battery compartment cover

5 a

.

Note: When the battery is low, the LED indicator

2

blinks.

Always replace all batteries at the same time. Only use batteries

from the same manufacturer and with the same capacity.

Remove the batteries from the product if it will not be in use for a

prolonged period of time. In long periods of storage the batteries

can corrode and can run themselves down.

Switching on / oﬀ

To switch the product on, push the LOCK switch

4

to the

position

. Immediately after being switched on, the product

releases two laser lines from the laser beam opening

7

.

To switch the product oﬀ, push the LOCK switch

4

to the

position

. When switched oﬀ, the pendulum unit is locked.

Use automatic levelling system

To work with automatic levelling, place the product on a level, ﬁrm

surface, or fasten it with the

- tripod thread

6

to the tripod.

When it is switched on, the automatic levelling system automatically

corrects irregularities of ±4° within the self levelling area. The level-

ling is concluded when the laser lines stop moving and the LED in-

dicator

2

goes green.

If automatic levelling is not possible, e.g. because the base of the

measuring tool deviates by more than 4° from the horizontal or

because the product is being freely hand-held, the LED indicator

2

will go red and the horizontal and vertical laser lines will be

switched oﬀ.

Note: operation without automatic levelling will always be indi-

cated via the red LED indicator

2

.

12 GB

Note: if the product is agitated or its position is changed during

operation, the product will automatically re-level. After re-levelling

check the positions of the horizontal and vertical laser lines against

reference points to avoid errors.

Using individual lines and crossed lines

When the product is performing automatic levelling and the base

of the measurement device deviates from the horizontal by less

than 4° (green LED on), carefully press the H-button

1

to turn the

horizontal line on or oﬀ.

Or correspondingly press the V-button

3

to turn the vertical line

on or oﬀ.

Crossed lines can be locked with this product:

When the product is performing automatic levelling and the base

of the measurement device deviates from the horizontal by less than

4° (green LED on) hold down the H-button

1

until the LED indica-

tor

2

goes red. Now automatic levelling is switched oﬀ and the

crossed lines are permanently switched on - even if the base of the

measurement device deviates from the horizontal by more than 4°.

You can turn this mode oﬀ again by pressing and holding down the

H-button

1

until the LED indicator

2

goes green again. The auto-

matic levelling system has been switched on again.

The crossed lines are turned oﬀ as soon as the base of the measuring to

ol

deviates from the horizontal by more than 4°, and the LED indicator

2

will turn red again.

Working without the automatic

levelling system

Put the LOCK switch

4

into the position .

Hold down the H-button

1

until the red LED indicator

2

comes

on. Now the product will release two laser lines from the laser

beam opening

7

that are not levelled. Operation without automatic

levelling will always be indicated via the red LED indicator

2

.

Practical guidance

Always use only the middle of the laser line for markings. The width

of the line depends on the distance.

13 GB

Working with the tripod

Setup and alignment

1. Pull all the three legs

17

of the tripod apart. The plastic ring

15

,

which is connecting all the three cross hinges will be moved to the

end of the middle column.

2. Release the blocking levers

16

and extend the legs until you get

your desired height.

3. Then, fold-back all those blocking levers

16

.

4. Check the straight positioning by using the bubble level

11

. If the

tripod is straight, the air bubble will be positioned in the centre of

the circle. If necessary, readjust the length of the legs

17

.

5. If additional height is necessary, loosen the locking screw

14

and

extend the centre column to desired height. Once reached the

desired height, tighten the locking screw

14

.

6. For a horizontal alignment of the tripod ﬂat head

18

, loosen the

long handle

12

by turning anti-clockwise and move the handle up

or down as desired. If the air bubble of the spirit level

11

is located

exactly in the middle of the circle, the tripod ﬂat head is aligned

horizontally. Then, tighten the long handle

12

by turning it clockwise.

7. If necessary, loosen the locking screw

13

to rotate the tripod ﬂat

head

18

up to 360 degree horizontally to get desired side. Once

reached the desired side, tighten the locking screw

13

.

8. If necessary, loosen the locking screw

10

to adjust the angle of the

tripod ﬂat head

18

up to 90 degree vertically to get desired angle.

Once reached the desired angle, tighten the locking screw

10

.

Securing the Cross Line Laser

Align

-thread

6

of cross line laser with the -quick-release ﬁxing

screw

8

of the quick shoe and make sure to tighten the screw well by

screwing the metal bracket

9

clockwise. The metal bracket

9

is on

the bottom side of the quick shoe

19

.

Removing quick shoe from tripod:

User can just remove the cross line laser together with quick shoe

19

from tripod by following below steps:

1. Pull the lever

11a

on the tripod ﬂat head

18

along the side.

2. Remove the quick shoe

19

.

3. If want to put back the cross line laser on the tripod again, pull the

lever

11a

on the tripod ﬂat head

18

and place the quick shoe

19

back ﬁrmly on the tripod ﬂat head

18

. Then, release the lever

11a

to bring back to original position and to ﬁrmly hold the quick shoe

19

(see ﬁg. A).

14 GB

4. Check the tight ﬁtting of the quick shoe

19

within the tripod ﬂat

head

18

.

Maintenance and cleaning

The product requires no maintenance.

ATTENTION! Never submerge the product in water or other liquid

s.

Do not allow water to enter into the product during cleaning.

Keep the product clean to ensure good, secure work.

Use a dry cloth to clean the outside.

Clean the laser beam opening

7

with a soft air jet. In cases of

heavy contamination, remove the dirt with a slightly damp Q-tip.

Do not exert any strong pressure!

For repair purposes the product may only be

opened by a professional.

Have the measuring tool repaired by qualiﬁed professionals and

only with original replacement parts. This ensures that the safety of

the measuring tool is maintained.

Storage

If you will not be using the product for a prolonged period of time,

remove the batteries and store it in a clean, dry place that is not

exposed to direct sunlight.

Disposal

The packaging is made entirely of recyclable materials, which you

may dispose of at local recycling facilities.

b

a

Observe the marking of the packaging materials for waste

separation, which are marked with abbreviations (a) and

numbers (b) with following meaning: 1–7: plastics / 20–22:

paper and ﬁbreboard / 80–98: composite materials.

The product and packaging materials are recyclable, dispose

of it separately for better waste treatment. The Triman logo

is valid in France only.

Contact your local refuse disposal authority for more details

of how to dispose of your worn-out product.

15 GB

To help protect the environment, please dispose of the product

properly when it has reached the end of its useful life and not

in the household waste. Information on collection points and

their opening hours can be obtained from your local authority.

Faulty or used batteries / rechargeable batteries must be recycled in

accordance with Directive 2006/66/EC and its amendments. Please

return the batteries / rechargeable batteries and / or the product to the

available collection points.

Environmental damage through incorrect dis-

posal of the batteries / rechargeable batteries!

Batteries / rechargeable batteries may not be disposed of with the

usual domestic waste. They may contain toxic heavy metals and are

subject to hazardous waste treatment rules and regulations. The chemi-

cal symbols for heavy metals are as follows: Cd = cadmium, Hg =

mercury, Pb = lead. That is why you should dispose of used batteries /

rechargeable batteries at a local collection point.

Warranty

The product has been manufactured to strict quality guidelines and

meticulously examined before delivery. In the event of product defects

you have legal rights against the retailer of this product. Your legal

rights are not limited in any way by our warranty detailed below.

The warranty for this product is 3 years from the date of purchase. The

warranty period begins on the date of purchase. Please keep the origi-

nal sales receipt in a safe location. This document is required as your

proof of purchase.

Should this product show any fault in materials or manufacture within

3 years from the date of purchase, we will repair or replace it – at our

choice – free of charge to you. This warranty becomes void if the

product has been damaged, or used or maintained improperly.

The warranty applies to defects in material or manufacture. This war-

ranty does not cover product parts subject to normal wear, thus possi-

bly considered consumables (e.g. batteries) or for damage to fragile

parts, e.g. switches, rechargeable batteries or glass parts.

16 GB

Warranty claim procedure

To ensure quick processing of your case, please observe the following

instructions:

Please have the till receipt and the item number (e.g. IAN 123456_7890)

available as proof of purchase.

You will ﬁnd the item number on the rating plate, an engraving on the

front page of the instructions for use (bottom left), or as a sticker on the

rear or bottom of the product.

If functional or other defects occur, please contact the service depart-

ment listed either by telephone or by e-mail.

You can return a defective product to us free of charge to the service

address that will be provided to you. Ensure that you enclose the proof

of purchase (till receipt) and information about what the defect is and

when it occurred.

Service

Service Great Britain

Tel.: 08000569216

E-Mail: [email protected]

17 HU

Az alkalmazott piktogramok

jelmagyarázata ............................................................ Oldal 18

Bevezető ............................................................................. Oldal 18

Rendeltetésszerű használat ...................................................Oldal 18

Alkatrészleírás ........................................................................Oldal 19

A csomag tartalma .................................................................Oldal 19

Műszaki adatok .....................................................................Oldal 19

Biztonsági utasítások ..............................................Oldal 20

Az elemekre / akkukra vonatkozó biztonsági tudnivalók ....Oldal 21

Üzembehelyezés .........................................................Oldal 22

Az elemek behelyezése / cseréje .......................................... Oldal 23

Be- / kikapcsolás .....................................................................Oldal 23

A kiegyenlítő-automatika használata ....................................Oldal 23

Az egyes és a keresztezett vonalak használata .................. Oldal 24

A kiegyenlítő-automatika nélküli munkavégzés ....................Oldal 24

A munkára vonatkozó tudnivalók .........................................Oldal 24

Állvánnyal történő munkavégzés: .........................................Oldal 25

Karbantartás és tisztítás .......................................Oldal 26

Tárolás .................................................................................. Oldal 26

Mentesítés .........................................................................Oldal 26

Garancia .............................................................................Oldal 27

Garanciális ügyek lebonyolítása ..........................................Oldal 28

Szerviz ....................................................................................Oldal 28

18 HU

Az alkalmazott piktogramok jelmagyarázata

Olvassa el a Használati utasítást.

Robbanásveszély!

Viseljen védőkesztyűt!

Figyelem!

Védje magát a lézersugárzástól!

Ne nézzen a lézerfénybe!

Egyenáram / -feszültség

Elemek mellékelve

Keresztvonalas lézer

Bevezető

Gratulálunk új termékének vásárlása alkalmából. Ezzel a

döntésével vállalatunk értékes terméke mellett döntött. A

használati utasítás ezen termék része. A biztonságra, a

használatára és a megsemmisítésre vonatkozó fontos tudnivalókat tar-

talmazza. A termék használata előtt ismerje meg az összes használati

és biztonsági tudnivalót. A terméket csak a leírtak szerint és a megadott

felhasználási területeken alkalmazza. A termék harmadik személy szá-

mára való továbbadása esetén kézbesítse vele annak a teljes dokumen-

tációját is.

Rendeltetésszerű használat

A termék a vízszintes és függőleges vonalak kiszámítására és ellenőr-

zésére alkalmas. A termék kizárólag zárt helyiségekben üzemeltethető.

Minden más jellegű használat vagy a termék megváltoztatása nem

19 HU

rendeltetésszerűnek minősül és rendkívül balesetveszélyes. A nem ren-

deltetésszerű használatból fakadó károkért a gyártó nem vállal felelős-

séget. Nem ipari felhasználásra való.

Alkatrészleírás

1

H-gomb (a vízszintes vonal be- / kikapcsolásához)

2

LED-ellenőrzőlámpa (piros: szintezés ki, zöld: szintezés be)

3

V-gomb (a függőleges vonal be- / kikapcsolásához)

4

LOCK-kapcsoló

5

Elemrekesz

5 a

Elemrekeszfedél

6

-os Állvány-menet (alsó oldal)

7

Lézer kimeneti nyílás

8

-rögzítőcsavar (a keresztvonalas lézer statív-csavarmeneté-

vel történő beállításhoz)

9

Fém tartórész (a cserélhető lemez csavarjának beállítására)

10

Biztosítócsavar (a statív lapos feje szögének jusztírozásához

90 fokig)

11

Vízszintmérő

11a

Kar (a cserélhető lemez rögzítésére)

12

Hosszú markolat

13

Biztosítócsavar (a statív lapos fején elforgatására vízszintesen

360 fokig)

14

Biztosítócsavar (a középső oszlop magasságának beállítására)

15

Műanyag gyűrű

16

Beállító kar (a lábak magasságának beállítására)

17

Statívlábak

18

Statív lapos fej

19

Cserélhető lemez

A csomag tartalma

1 körvonalas lézer

1 állvány

2 1,5 V-os elem, AA típus

1 használati útmutató

Műszaki adatok

Üzemi feszültség: 3 V (egyenáram)

Mukaterület legalább

1)

: 10 m

20 HU

Kiegyenlítési pontosság: +/- 0,5 mm/m

Tipikus önkiegyenlítő pontosság: ± 4°

Tipikus kiegyenlítési idő: kb. 4 másodperc

Üzemi hőmérséklet: +5 °C–35 °C

A levegő relatív páratartalma max.: ≤ 90 %

Lézerosztály: 2

Hullámhossz (λ): 635 nm

Maximális teljesítmény P max: 1mW

Állványfoglalat:

Elemek: 2 x 1,5 V-os elem, AA típus

A termék súlya: 260 g (elem nélkül)

Az állvány súlya: 320 g

A termék mérete: kb. 70 x 61 x 90 mm

Az állvány mérete: 65 cm

1) A mnkaterületet a kedvezőtlen környezeti körülmények

(pl. közvetlen napsütés) lecsökkenthetik.

Biztonsági utasítások

FULLADÁSVESZÉLY! A csomagolóanyaggal (pl. fóliák, vagy

polisztirol) nem szabad játszani. Tartsa távol a csomagolóanyagot

a gyerekektől. A csomagolóanyag nem játékszer.

Ne dolgozzon a mérőkészülékkel robbanásveszélyes környezetben,

ahol gyúlékony folyadék, gőz, gáz vagy por található. A termékben

szikrák képződhetnek, amelyek a port, vagy a gőzöket meggyújt-

hatják.

A terméket 8 éves kor feletti gyermekek, valamint korlátozott ﬁzikai,

érzékszervi vagy szellemi képességgel élő vagy nem megfelelő

tapasztalattal és tudással rendelkező személyek csak felügyelet

mellett, illetve a termék biztonságos használatára vonatkozó felvi-

lágosítás és/vagy a lehetséges veszélyek megértése után használ-

hatják. Ne hagyja a gyerekeket a termékkel játszani. A tisztítást és

karbantartást gyermek csak felügyelet mellett végezheti.

A bekapcsolt terméket ne hagyja felügyelet nélkül és a használat

végeztével kapcsolja ki azt. A lézersugár más személyeket megva-

kíthat. Szemsérülés veszélye.

Óvja a terméket nedvességtől és a közvetlen napsugárzástól.

Ne tegye ki a terméket szélsőséges hőmérsékletnek, vagy hőinga-

dozásnak. Ne hagyja azt pl. hosszabb időre az autóban. Nagyobb

hőingadozást követően hagyja, hogy a termék alkalmazkodjon a

hőmérséklethez, mielőtt üzembe veszi azt. Extrém hőmérsékleten,

vagy hőingadozás esetén a termék pontossága csökkenhet.

Stránka sa načítava...

Parkside PKLL 10 B3 Translation Of The Original Instructions

Parkside PKLL 10 B3 Translation Of The Original Instructions

v iných jazykoch

Súvisiace články

Ostatné dokumenty