IKEA HOO S00 S Program Chart

Značka: IKEA

Model: HOO S00 S

Kategória: Odsávače pár

Typ: Program Chart

5019 618 33026



HOO S00 - HOO S10 - HOO S40

KARTA INSTALACYJNA

Minimalna odległość od palników: 50 cm (od palników elektrycznych), 75 cm (od palników

gazowych, olejowych lub węglowych). Podczas montażu należy przestrzegać kolejności

numeracji (1

.....) oraz odpowiednich instrukcji. Nie należy podłączać urządzenia do

zasilania zanim nie zakończy się całkowicie jego montażu.

Uwaga! Rura odprowadzająca dym i parę oraz kolanka nie są dostarczane i należy je

zakupić oddzielnie.

POPIS INSTALACE

Minimální vzdálenost od sporáků: 50 cm (elektrické sporáky), 75 cm (sporáky na plyn, naftu

nebo uhlí). Při montáži sledujte číslování (1

.....) a příslušné pokyny. Spotřebič

připojte k elektrické síti až po úplném dokončení instalace.

Upozornění! Nasávací trubka a pásky k upevnění nejsou součástí vybavení, musíte je

zakoupit.

INŠTALAČNÁ SCHÉMA

Minimálna vzdialenost' od sporáka: 50 cm (elektrické sporáky), 75 cm (plynové sporáky,

sporáky na naftu alebo uhlie). Pri montáži postupujte podľa číslic (1

.....) a dodržujte

príslušné pokyny. Spotrebič nezapájajte do siete, kým nie je inštalácia úplne ukončená.

Upozornenie! Rúra na odvádzanie dymov a upevňovacie svorky sa nedodávajú, musíte ich

kúpit' samostatne.

ÜZEMBE HELYEZÉSI ÚTMUTATÓ

A tűzhelytől való minimális távolság: 50 cm (elektromos tűzhely), 75 cm (gáz-, olaj- vagy

széntüzelésű tűzhely). A felszereléshez kövesse a számozást (1

.....) és a vonatkozó

utasításokat. Ne helyezze feszültség alá a készüléket addig, amíg nem történt meg

maradéktalanul az üzembe helyezés.

Figyelem! Az elvezető cső és a rögzítőpántok nem tartozékok, így azokat külön meg kell

vásárolni.

61833026.fm Page 1 Thursday, June 24, 2004 6:28 PM

5019 618 33026

HOO S00 - HOO S10 - HOO S40



СХЕМА УСТАНОВКИ

Минимальное расстояние до конфорок: 50 см (электрические конфорки), 75 см

(газовые, керосиновые или угольные горелки). Последовательность действий

при монтаже должна соответствовать нумерации (1

.....) и приведенным

инструкциям. Не подключайте прибор к сети до тех пор, пока установка не будет

полностью закончена.

Внимание! Выпускная труба и крепежные зажимы не входят в комплект поставки

и приобретаются отдельно.

КАРТА ЗА ИНСТАЛИРАНЕ

Минимално разстояние от печки: 50 см (електрически печки), 75 см (печки с газ,

нафта или въглища). За монтаж следвайте номерацията (1

.....) и

съответните инструкции. Не включвайте уреда към мрежата, докато

инсталирането не е завършено докрай.

Внимание! Тръбата за отвеждане не е предоставена и трябва да се закупи

отделно.

FIȘA DE INSTALARE

Distanţa minimă de la arzătoare: 50 cm (arzătoare electrice), 75 cm (arzătoare pe bază de

gaze, motorină sau cărbune). Pentru montare urmaţi numerotarea (1

.....) și

instrucţiunile corespunzătoare. Nu branșaţi aparatul la curent până când nu terminaţi

definitiv operaţia de instalare.

Atenţie! Tubul de evacuare și manșoanele de fixare nu fac parte din dotare și trebuie să fie

cumpărate separat.

INSTALLATION SHEET

Minimum height above cooker: 50 cm (electric cookers), 75 cm (gas, gas oil or coal

cookers). To assemble follow the numbers (1

.....) and relative instructions. Do

not connect the appliance to the electrical power supply until installation is

completed.

Warning! The exhaust pipe and clamps are not supplied and must be bought

separately.

RUS

61833026.fm Page 2 Thursday, June 24, 2004 6:28 PM

5019 618 33026



HOO S00 - HOO S10 - HOO S40

61833026.fm Page 3 Thursday, June 24, 2004 6:28 PM

5019 618 33026

HOO S00 - HOO S10 - HOO S40



61833026.fm Page 4 Thursday, June 24, 2004 6:28 PM

5019 618 33026



HOO S00 - HOO S10 - HOO S40

61833026.fm Page 5 Thursday, June 24, 2004 6:28 PM

5019 618 33026



HOO S00 - HOO S10 - HOO S40

Preliminary information for installing the hood:

Expansion plugs are provided to secure the hood to most types of ceilings. A qualified technician is needed,

however, to make sure that the plugs are suitable for your ceiling. The ceiling must be strong enough to take

the weight of the hood.

Disconnect the power supply at the home main switch during electrical connections.

1. Adjust extension of the hood support structure, as the final height of the hood depends on this, and

remember that with installation completed the hood must be at least 50 cm above the hob in case of electric

cookers and 75 cm in case of gas or mixed cookers.

2. Fix the two sections of the structure using 8 screws.

3. Place the ceiling hole diagram directly above the hob (the centre of the diagram must match the centre of

the hob and the edges must be parallel to the sides of the hob - the side of the diagram with the wording

FRONT corresponds to the control panel side). Prepare the electrical connection.

4. Drill as shown (6 holes for 6 wall plugs - 4 plugs for hooking), screw the 4 outer screws leaving a space of

about 1 cm between the screw head and the ceiling.

5. Fit an exhaust pipe inside the truss and connect it to the collar of the motor compartment (exhaust pipe

and clamps are not provided).

6. Hook the truss to the 4 screws (see step 4).

CAUTION! The side of the truss with connection box corresponds to the side of the control panel with

hood assembled.

7. Tighten the 4 screws.

8. Insert and tighten another 2 screws in the remaining free holes for secure fixing.

9. Carry out the electrical connection to the mains power supply, only turn on the power supply with

assembly completed.

10. Hook the hood to the truss, check for perfect hooking - to hook the hood to the truss partially screw

4 screws (also see step 12).

11. Fixing the hood to the truss with two screws, will also facilitate centering the two parts.

12. Tighten the 4 screws fixing the truss to the hood.

13. For extractor operation (13A), connect the other end of the exhaust pipe to the home drain device.

For filter operation (13F), fit deflector F on the truss and fix it with 4 screws to the special bracket. Finally,

connect the exhaust pipe to the collar located on the deflector.

14. Fit the nuts with fixing hooks supplied inside

the top and bottom sections of the flues at the rectangular

slots. A total of 14 nuts must be fitted.

15. Join the two top sections of the flue to cover the truss so that one of the slots on the sections is situated on

the same side of the control panel and the other on the opposite side.

Screw the two sections with 8 screws and spring clips (4 each side - see the plan diagram for joining the

two sections).

16. Fix the top flue assembly to the truss, near the ceiling, with two screws (one each side).

17. Carry out electrical connection of control panel and bulbs.

18. Join the two bottom sections of the flue covering the truss using 6 screws and spring clips (3 each side - also

see the plan diagram for joining the two sections).

19. Insert the bottom section of the flue in the special seat to completely cover the motor compartment and

electrical connection box, and fix the hood with two screws from the inside.

20. Apply the 2 tabs (supplied) to cover the fixing points of the bottom flue (CAUTION! THE BOTTOM FLUE

TABS ARE THE NARROWER AND SHALLOWER ONES).

The wider and deeper tabs are those used for the top flue, and must be cut to size.

21. Turn the mains power on again at the central electrical panel and check for correct hood operation.

INSTALLATION - ASSEMBLY INSTRUCTIONS

ROSK H RUS BGCZPL GB

61833026.fm Page 21 Thursday, June 24, 2004 6:28 PM

5019 618 33026

HOO S00 - HOO S10 - HOO S40



1. Control panel.

2. Grease filter.

3. Halogen bulbs.

4. Steam deflector.

5. Telescopic flue.

To clean the grease filter

Wash the grease filter at least once a month.

1. Disconnect the electrical power supply.

2. Remove the grease filters - Fig. 2: pull the spring

release handle (f) downwards, then remove the

filter.

3. After cleaning the grease filter refit in reverse

order, making sure the entire extraction surface is

covered.

Carbon filter Fitting and Maintenance

Fitting the carbon filter:

1. Disconnect the electrical power supply.

2. Remove the grease filter (f - Fig. 2).

3. Turn the side knobs 90° and then remove the

filter holder (g - Fig. 3).

4. Fit the carbon filter (h - Fig. 3) in the filter holder

(i - Fig. 3).

5. Refit the filter holder and secure it to the hood

with the screw (g - Fig. 3).

6. Refit the grease filter.

Carbon filter maintenance:

Unlike traditional carbon filters, this carbon filter can

be washed and reactivated.

With normal hood use, the filter should be cleaned

once a month. The best way to clean the filter is in a

dishwasher at the highest temperature possible, using

a normal dishwasher detergent. To avoid particles of

food or dirt settling on the filter during washing and

giving rise to unpleasant smells, it is advisable to wash

the filter on its own. After washing, dry the filter in the

oven at 100° C for 10 minutes to reactivate it.

The filter will retain its odour-absorbing capacity for

three years, after which it must be replaced.

Replacing bulbs

1. Disconnect the electrical power supply.

2. Use a small screwdriver or any other suitable tool

to prise off the lamp cover (Fig. 4).

3. Remove the burnt-out bulb.

Replace it with a PHILIPS STANDARD LINE bulb,

code 425409 12 V 20 W 30° GU4 Ø 35mm, or

similar.

4. Close the lighting unit (snap-close).

CONTROL PANEL

A. Light ON/OFF switch.

B. ON/OFF and speed 1 selector switch

(small amount of steam and fumes).

B+C.Speed 2 selector switch

(medium amount of steam and fumes).

B+D.Speed 3 selector switch

(large amount of steam and fumes).

Fig. 1

Fig. 2

Fig. 3

Fig. 4

PRODUCT SHEET

ROSK H RUS BGCZPL GB

61833026.fm Page 22 Thursday, June 24, 2004 6:28 PM

IKEA HOO S00 S Program Chart

Značka: IKEA

Model: HOO S00 S

Kategória: Odsávače pár

Typ: Program Chart

Stiahnite si PDF

správa

v iných jazykoch

English: IKEA HOO S00 S
polski: IKEA HOO S00 S
română: IKEA HOO S00 S

IKEA HOO S00 S Program Chart

IKEA HOO S00 S Program Chart

v iných jazykoch

Súvisiace články

Ostatné dokumenty