CHOETECH BS005 Používateľská príručka

Portable Power Station

User Manual • Uživatelský manuál •

Užívateľský manuál • Használati utasítás •

Benutzerhandbuch

2

English

3 – 17

Čeština

18 – 32

Slovenčina

33 – 47

Magyar

48 – 62

Deutsch

63 – 78

3

Dear customer,

Thank you for purchasing our product. Please read the following instructions carefully

before first use and keep this user manual for future reference. Pay particular attention to

the safety instructions. If you have any questions or comments about the device, please

contact the customer line.

✉ www.alza.co.uk/kontakt

✆ +44 (0)203 514 4411

Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Prague 7, www.alza.cz

4

Thank you very much for purchasing 1200W power station. Be sure to read this manual

carefully before using the product in order to use the product correctly. This manual is

needed for product after-sales service. Please keep this manual together with the invoice

and other purchase certificates.

In order to ensure the safety of this product during transportation, this product is only

charged about 30% when it is packaged. Please recharge when you get the product.

The product can be charged directly by the wall socket, please do not use extension cords

and able taps.

When the product is charging, do not plug other products in the same pocket.

Warning

 Please avoid using the product near hight temperature, high humidity, direct sun

environment and fireplace.

 Do not disassemble or modify this product, it will cause malfunction and fire.

 Please discard or recycle the product according to the methods prescribed by local

laws.

 Be careful not to drop the product from a hight place and give the product a strong

impact.

 Keep or use the product in a place out of the reach of children.

 Please use our company’s genuine accessories. The damage caused by the use of

non-genuine accessories cannot be repaired free of charge.

 Please leave a space of about 30cm away from the side suction and exhaust ports,

so as not affect the heat dissipation of the product.

 When not using this product, please turn off the power and unplug the power cord.

Please avoid storing the product in a place exposed to direct sunlight with high

temperature and humidity.

 For long-term storage, please consume power from full power to no power once

every 3 months, and then recharge to about 50%.

 Please do not use this product and its accessory cables and connecting equipment

when there is a defect.

 Please do not store the product for a long time in extremely hight and low

temperature places such as in the car and in the field warehouse to avoid

shortening the battery life.

5

AC Output Parameter

Type of AC port

AC output

US/JP

100V~120V 50/60Hz

CH

220V 50Hz

UK

230V 50Hz

EU

220V~240V 50Hz

KR

220V 60Hz

Packaging List

Power Station

AC Charger

User Manual

6

Product introduction

This product is a 960Wh large capacity 1200W high power, 1.5 hours of hight-speed

charging portable energy storage power supply, suing hight safety performance of LiFePo4

battery.

It can be used as a backup power supply in case of emergency power cut, disaster,

camping and vehicles, and can also provide power for various electric tools.

1200W hight power, pure sine wave AC output, can be used for house-hold appliances

such as dryers, microwave ovens, refrigerators, high-power induction cookers and it can

also be used for other electronic devices such as personal computers.

Through the 700W ultra-fast charging, this model can be full charged within 1.5 hours, The

AC input/output voltage frequency can automatic or manually switched between

50Hz/60Hz. This product also supports maximum 500W solar charge, allow you to charge

even when the power cut in outdoor situations.

1. Main power control

2. Light control

7

3. USB control

4. DC control

5. LDC display

6. Air intake/outlet

7. AC on/off control (50Hz/60Hz switching control)

8. Anderson input port (for solar panel)

9. AC input port

10. Overload protection

Main Power Control

Main Control for the whole system turns on/of.

Operate method: long press the button for 3s to turn on/off the system.

LED light control

Operate method: sort press to turn on and change the light mode (SOS/Flash).

Note: you can turn off the light by long press the button (1-2s) in any mode.

USB button

Operate method: short press to turn on/off

USB-A x 2

Type-C x 1

Type-C x 3

5V/2.4A

PD-100W

PD-20W

DC button

Operate method: short press to turn on/off

Output x 2

Cigar Lighter x 1

12V/3A

12V/10A

LCD display

Present the remaining power and using data.

Cooling system

When the fans are working, please don’t block the channel.

8

AC button (AC output, total share 1200W)

Operate method: short press to turn on/off.

Notice:

1. Please confirm the output voltage or frequency before using.

2. Long press the button for 2s to entry frequency changing mode, 50Hz and 60Hz will

blink in the display, press again the button to choose the right frequency, wait till

the frequency is not blinking, then you will get the frequency you want.

3. Quick short press for 10 times to switch the voltage 100V or 110V.

Solar panel input

Use the included Anderson -> MC4 conversion cable to connect the solar panel.

1. Solar panels can have maximum input of 500W and a maximum voltage of 50V.

2. If exceeding the maximum voltage leads to equipment damage, it is beyond the

scope of warranty.

AC Input

Use wall socket to get 700W fast charging, which can full charge from 0 to 100% in 1.5

hours.

 The product can be charged directly by the wall socket, please do not use

extension cords and cable taps. When the product is charging, do not plug other

products in the same socket.

 Please do not plug several devices together in a extension socket at once, the

current will be to hight and bring damage to the cable and fire risk.

 Do not use the same socket to connect other devices when charging this product.

When the same wiring in a general household exceeds 1500W, The safety circuit

breaker will be activated.

Overload protector

To protect this product, an overload protector is added. Prevent damage to the product

due to excessive AC input current caused by lighting and power grid fluctuations. When

such a situation occurs, the overload protector will start to cut off the AC input protect the

product.

Restore the AC input function of the product in the following sequence.

1. Turn off the power button and unplug all ports.

2. After confirming that all parts are normal, turn on the power button.

3. Press the overload protection button to switch on the AC line to restore AC input.

9

Display icon introduce

1. Charging/using time

2. Fan state

3. High/low temperature protection

4. Power percentage

5. Total input power

6. Total output power

7. LED light

8. AC output

9. Type-c output

10. USB output

11. AC charging

12. Anderson charging

13. DC output

14. Cigar lighten output

Display Attention

When the icon lights up. Please keep Air intake/outlet unobstructed.

When this icon lights up. Please note the device is now with hight/low temperature

and will possibly stop working till the temperature back to normal standard.

When this icon is blinking, representant that the AC input is fault, please recheck

(Power/Hz/cable)

When the icon is blinking, represent the output is fault,

please recheck.

UPS mode

10

UPS function

This product has the bypass mode, does not need to pass through the battery, can directly

output from the AC.

In UPS mode, when the AC input power of the mains is cut off due to a power outage, the

acc input power of the mains can be used in about automatic switch to product battery

power within 10 ms to ensure AC output.

UPS Connections

As shown in the figure below, connect the product between the socket on the wall and the

electrical appliances, and the power of the product is in the ON state. When you turn on

the power of the electrical appliances, it will directly use the AC power of the power grid.

In this state, when the power grid is cut off, it will automatically switch to the product’s

internal battery to supply power.

 In UPS mode of The United States and Japan, the maximum power output of AC is

below 1100W, and the AC output exceeds 1100W. The AC output icon “ ” blinks

indicating overload.

 In UPS mode of China, United Kingdom, Europe and South Korea, AC output of the

maximum power below 1200W, AC output over 1200W, “ ” AC output icon flashes

indicating overload.

Solar panel connection

Our product can be connected to solar panels and can be charge through solar panels.

The solar panels produce 400 watts of power and can be fully charged in as little as 4

hours. Solar panel input can be the most maximum 500W (maximum voltage 50V)

 Solar panel charging power, according to the weather and climate conditions.

 Solar panel voltage exceeding 50V will damage the equipment and may not be

covered by warranty.

11

By solar panels

Connecting Pattern 1

Connecting Pattern 2

Car charging

This product can be charged by the cigarette lighter in the car with an ACC cable

(accessory: AC hereinafter)

Turn on the power of this product, connect the ACC charging cable to the cigarette lighter

in the car and the Anderson interface on the side of the product, turn on the engine of the

car, and the LCD of this product will show the input power.

 On-board charging should be carried out with the car engine turned on. If the

engine is not turned on, the battery might run out.

 Car charging is usually low power of 90-120W, and the charging time will be long. If

you need to quid charge, it is recommended to use the mains.

Anderson to MC4 (Not included in

accessory)

Solar panel

Device

The area of charging

Solar panel (B) (Not included in

the accesory)

Anderson to MC4 (Not included in

accessory)

Device

Solar panel (A) (Not included in

the accesory)

12

Fault resolution

Status

Explanation

Recover method

Output exceeds standard,

short circuit

1. Remove the load.

2. Check whether the

overload protector is

up. If it is up, press the

overload protection

button is pressed, press

the AC output button.

3. If the overload protector

does not spring up,

directly press AC output

Restore output function.

The temperature warning

icon flashes and buzzes

The temperature of this

product has exceeded the

appropriate temperature

The temperature of this

product has exceeded the

appropriate temperature

Charging unavailable

Bad wire connection

Confirm the connection

status of the line and the

power supply status.

Overload protection

function activated

1. Turn off the power

button and remove

cables from all ports.

2. After verifying that all

components are

normal, turn on the

power button.

3. Press the overload

protection button to

connect the AC cable to

recover AC input.

Specifications

Product name

1200W Portable Power station

Product size

L*W*H=387*228*316mm

Product weight

13.5kg

Capacity

960Wh

AC Charging

50/60 Hz 700W max

Car charging cable

accessories (Not in the

accessory)

Device

13

MPPT input

11.5-50V 20A 500W max

AC output

AC output: 50/60Hz (frequency switch

available), rated 1200W, 2400W peak pure

sine wave. Built-in overload and short

circuit protection.

USB

USB-A (5V 2.4A) x 2

Type-C

5-20V/5.0A, PD3.0 100Wx1 ; 5-12V,

PD20Wx3

DC 5521

12V/3A x 2

Cigar lighter output

12V/10A

Power off current

<500uA

Operating temperature

-10~40°C

Charging temperature

0~40°C

Environment humidity

≤90%RH

Battery specification

Battery type

40135 LiFePo4

Single cell rated voltage

3.2V

Single cell rated capacity

20Ah

Battery pack rated voltage

48V

Battery output voltage

42-54V

Battery pack rated capacity

960Wh

14

Attention

Product is not permitted on aircraft.

To maintain battery health, use and recharge at least once every 3 months.

To ensure best performance, we strongly recommend using the original or

certified charger and cables.

The product is not waterproof. Please do not expose to rain or liquids.

Do not disassemble the product.

Please avoid dropping the product.

Please avoid extreme temperatures.

Please dispose of batteries and electronic good in accordance with local

regulations.

15

Warranty Conditions

A new product purchased in the Alza.cz sales network is guaranteed for 2 years. If you

need repair or other services during the warranty period, contact the product seller

directly, you must provide the original proof of purchase with the date of purchase.

The following are considered to be a conflict with the warranty conditions, for

which the claimed claim may not be recognized:

 Using the product for any purpose other than that for which the product is intended or

failing to follow the instructions for maintenance, operation, and service of the product.

 Damage to the product by a natural disaster, the intervention of an unauthorized

person or mechanically through the fault of the buyer (e.g., during transport, cleaning

by inappropriate means, etc.).

 Natural wear and aging of consumables or components during use (such as batteries,

etc.).

 Exposure to adverse external influences, such as sunlight and other radiation or

electromagnetic fields, fluid intrusion, object intrusion, mains overvoltage, electrostatic

discharge voltage (including lightning), faulty supply or input voltage and inappropriate

polarity of this voltage, chemical processes such as used power supplies, etc.

 If anyone has made modifications, modifications, alterations to the design or

adaptation to change or extend the functions of the product compared to the

purchased design or use of non-original components.

16

EU Declaration of Conformity

Identification data of the manufacturer's / importer's authorized representative:

Importer: Alza.cz a.s.

Registered office: Jankovcova 1522/53, Holešovice, 170 00 Prague 7

CIN: 27082440

Subject of the declaration:

Title: Portable power station

Model / Type: BS005

The above product has been tested in accordance with the standard(s) used to

demonstrate compliance with the essential requirements laid down in the

Directive(s):

Directive No. 2014/30/EU

Directive No. 2014/35/EU

Directive No. 2011/65/EU as amended 2015/863/EU

17

WEEE

This product must not be disposed of as normal household waste in accordance with the

EU Directive on Waste Electrical and Electronic Equipment (WEEE - 2012/19 / EU). Instead,

it shall be returned to the place of purchase or handed over to a public collection point for

the recyclable waste. By ensuring this product is disposed of correctly, you will help

prevent potential negative consequences for the environment and human health, which

could otherwise be caused by inappropriate waste handling of this product. Contact your

local authority or the nearest collection point for further details. Improper disposal of this

type of waste may result in fines in accordance with national regulations.

18

Vážený zákazníku,

Děkujeme vám za zakoupení našeho produktu. Před prvním použitím si prosím pečlivě

přečtěte následující pokyny a uschovejte si tento návod k použití pro budoucí použití.

Zvláštní pozornost věnujte bezpečnostním pokynům. Pokud máte k přístroji jakékoli dotazy

nebo připomínky, obraťte se na zákaznickou linku.

✉ www.alza.cz/kontakt

✆ +420 225 340 111

Dovozce Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Praha 7, www.alza.cz

19

Děkujeme za zakoupení 1200W elektrárny. Před použitím výrobku si určitě pečlivě

přečtěte tento návod, abyste výrobek používali správně. Tento návod je potřebný pro

poprodejní servis výrobku. Uschovejte prosím tento návod společně s fakturou a dalšími

doklady o koupi.

Aby byla zajištěna bezpečnost tohoto výrobku během přepravy, je tento výrobek při balení

nabit na 30 %. Při převzetí výrobku jej prosím dobijte.

Výrobek lze nabíjet přímo ze zásuvky, nepoužívejte prodlužovací kabely.

Když se výrobek nabíjí, nezapojujte do stejné zásuvky jiné výrobky.

Varování

 Nepoužívejte výrobek v blízkosti vysokých teplot, vysoké vlhkosti, přímého slunce a

krbu.

 Tento výrobek nerozebírejte ani neupravujte, způsobilo by to poruchu a požár.

 Výrobek zlikvidujte nebo recyklujte v souladu s místními zákony.

 Dávejte pozor, abyste výrobek neupustili z vysokého místa a nezpůsobili silný

náraz.

 Výrobek uchovávejte nebo používejte na místě mimo dosah dětí.

 Používejte prosím originální příslušenství naší společnosti. Poškození způsobené

použitím neoriginálního příslušenství nelze bezplatně opravit.

 Od bočních nasávacích a výfukových otvorů ponechte prostor asi 30 cm, aby

nedošlo k ovlivnění odvodu tepla z výrobku.

 Pokud tento výrobek nepoužíváte, vypněte napájení a odpojte napájecí kabel.

Neskladujte výrobek na místě vystaveném přímému slunečnímu záření s vysokou

teplotou a vlhkostí.

 Pro dlouhodobé skladování spotřebujte jednou za 3 měsíce energii z plného výkonu

na nulový a poté ji dobijte na přibližně 50 %.

 Nepoužívejte tento výrobek a jeho přídavné kabely a připojovací zařízení, pokud se

na nich vyskytne závada.

 Neskladujte výrobek po dlouhou dobu na místech s extrémně vysokou a nízkou

teplotou, například v autě nebo ve skladu v terénu, aby nedošlo ke zkrácení

životnosti baterie.

20

Parametr výstupu AC

Typ portu AC

Výstup střídavého proudu

USA/JP

100 V~120 V 50/60 Hz

CH

220 V 50 Hz

UK

230 V 50 Hz

EU

220 V ~ 240 V 50 Hz

KR

220 V 60 Hz

Seznam balení

Elektrárna

Nabíječka AC

Uživatelská příručka

Stránka sa načítava...

CHOETECH BS005 Používateľská príručka

CHOETECH BS005 Používateľská príručka

v iných jazykoch

Súvisiace články

Ostatné dokumenty